How to reset TVI DVR/ POE NVR / Wireless NVR (ZSWNVK-H) System when you forgot the password?

1) You can find the correct model number on the label at the bottom of the DVR / NVR System.

2) Find the DVR / NVR’s device ID/UID.

A. You can find the DVR’s ID on the label of the DVR / NVR.

How to reset Password Zosi DVR NVR Poe All Model

B. Or you can also reboot the DVR / NVR system and wait until Wizard Page display, then find the UID.

3) Please send us the model number and device ID / UID, we will create a super password for you.

    NOTE: The User Name corresponding to super password must be ‘admin’.

                 Once you set super password this time, the login password should be blank

                 in the next time when you reboot it or log in again.

                 You can go to DVR’s Main Menu – Setup – User – Change password to set a new

                 password. (Please keep the old password blank, you just need to input the new

                 password and confirm password.)

Beyond that, you can also upgrade software by means of upgrade file from us, then reset password when reboot DVR.

Connecting the DVR / NVR to the internet

This method works for the following models of DVRs / POE NVRs / Wireless NVRs:

4-Channel DVRs / POE NVRs / Wireless NVRs:

ZR04ZN;   ZR04ZM;   ZR04FN;   ZR04FM;   ZR04CN;   ZR04CM;   ZR04JS;   ZR04TS;   ZR04TN

ZR04RN;   ZR04RM;   ZR04EN;   ZR04EM;   

ZR04DS;   ZR04MS;  

8-Channel DVRs / POE NVRs / Wireless NVRs:

ZR08ZN;   ZR08ZM;  ZR08FN;   ZR08FM;   ZR08BN;   ZR08BM;   ZR08CN;   ZR08CM;   ZR08KS;   ZR08TN

ZR08RN;   ZR08RM;   ZR08EN;   ZR08EM;      

ZR08DS;   ZR08DP;   ZR08MS;   

16-Channel DVRs:

ZR16ZK;   ZR16JK;   ZR16BK;   ZR16CK

(You can find the model number on the label at the bottom of the DVR.)

If your CCTV DVR or NVR don’t have a built-in WiFi support, then you have to run internet cable (CAT 5 or CAT 6 Ethernet cable) to connect your DVR or NVR to the internet via the router.

• Connect one end of the Ethernet cable to the Ethernet input on the back of the DVR.
• Connect the other end of the Ethernet cable into a device providing an active internet connection, such as a router or modem.
• Test your internet connection to confirm that it is active by going to the Network > Network screen.

1) Right click mouse—go to Main Menu > Setup > Network.

2) On the Network tab, ensure the “Obtain an IP Address Automatically” option is enabled, and that there is no information in the PPPoE fields.

3) Once you’ve ensured there is no information in the PPPoE field and that the “Obtain and IP Address Automatically” option is selected, select the “Test” option.

If “OK” is displayed, the local area network is connected successfully.

If the DVR is not able to connect to the internet, you will get a message that states “Cannot Connect to Network”.

NOTE:

In order for other devices to connect to the DVR through the router, the DHCP setting must be enabled from the router’s settings page.

If you still cannot connect to the network, please ensure that you don’t have a firewall active on your network that may be limiting the connection.

You may need to open ports 80, 5000, and 5001 on your router, if they’re currently being blocked by te firewall. This typically only happens on commercial internet accounts, as they deal with sensitive transactions, but occasionally a firewall on a residential line will also block these ports.

If you’re unsure how to open ports on your router, you will need to speak with the router manufacturer.

FAQ:

1) What’s DHCP?

DHCP is a type of internet networking approach. It stands for Dynamic Host Configuration Protocol. It means that a router assigns IP addresses to each of the devices on the network, allowing them to communicate with other devices in or outside the network.

In context of our systems, the setting related to DHCP is called DHCP server status. This setting enables your router to obtain the static IP address on the DVR and broadcast that IP to the app so it can locate your DVR. This setting needs to be enabled on a router for the apps to be able to connect to the DVR systems.

2) For example: How to set up a linksys E5350 Router?

Once you’ve logged into the router settings, you’ll want to select “configuration” at the top, and then “Connection > Local Network” in the menu on the left. You should see this page:

​

You’ll want to ensure the checkbox beside “DHCP server” is checked off, and set the start IP address to 100 as shown in the image. Leaving the other settings here as they default should be fine. Once this is done, select “save.” Before proceeding with the next steps, try using the app while not connected to local WiFi. If you can see the live feeds, you don’t need to complete the steps below.

If you can’t, you’ll need to open the ports in the firewall. On the left menu, select “Security”, and then “Single Port forwarding” as shown in this image:

​

Select the button on this page for “Add a new Single Port Forwarding”, and this window should appear:

​

The number you want to enter in the “To IP Address” field is the last three digits of the DVR’s static IP, which you can find on the Network page of the DVR. (Main Menu > Setup > Network)

Application and protocol can be left as they are, and you’ll want to check off the “enabled” box. You’ll need to do this 3 times, using the following information:

1.
Application Name: DVR HTTP
External Port: 80
Internal Port: 80

2.
Application Name: DVR Mobile
External Port: 5000
Internal Port: 5000

3.
Application Name: DVR E-mail
External Port: 5001
Internal Port: 5001

After filling the box with the necessary info for each port, select “apply”, and then hit the add button again to reopen the window. Once all 3 ports are opened, try testing the app again.

Note:  different Routers may have different setting interfaces.

More questions, please feel free to contact us.

Our Whatsapp:  +1-866-841-6932

Support Email address:  service@zositech.com

Our Facebook:  https://www.facebook.com/ZosiTechnology/

Support center: support@zositechhelp.zendesk.com

<p>The post How to reset Password Zosi DVR NVR Poe All Model first appeared on NVR IPCAMERA SECURITY.</p>

We can talk directly on phone app for asking courier to put package to a certain place you point, and hear sound from app or TV monitor connected to NVR

We could be alerted any time a person enter your property by receiving push notification from free phone APP, and the alarm light will be triggered to drive away the suspicious objects ( Note: APP has No Monthly Fees)

High Resolution 2592 X 1944 pixel to provide your vivid and clear image no matter in day or night, and IP 67 Waterproof to withstand Changeable Weather like Snowy/Rainy Day

We can customize the surveillance area or set a line for human/vehicle, and the alarm alerts will be triggered when detecting human/vehicle crossing the line or intruding the alarm area （These function may only work with Hiseeu NVR）

Version 2020-2022 PoE System FAQs in total

.

Further support, plz email us at email love@hiseeu.com

Or contact us at +1 917 688 2228

.

Important Notes:

These FAQs are only adaptable to following Models NVR Model : H5-NVR-P-8,

Camera Model: HB215-PA, HB212-PA, HB915B-PA

Mobile Phone APP: XMEye Pro         PC Client :VMS

Hisseu PoE Camera System User Guide v1

Contents:

A:  Forget NVR Password?

B:  Add Device on PC Client Software (VMS）?

C:  How to Sign up account on Mobile APP (XMEye Pro) ?

D:  Add Device on Mobile Phone APP (XMEye Pro)?

E:  How to enable Alarm Notifications on APP XMEye Pro?

F:  Configure Offline Camera or Add a New Camera?

G:  No Video Display on TV Monitor Or Blank Screen?

H:  Why DVR/NVR can’t record or playback video?

.

Detail Solutions:

A:  Forget NVR Password?

1. Please click the mouse from the home screen, and “Logo Out–>Log Out”

2. Right click the mouse again, click “ Main Menu”–> “Forget password –> Forget answer”, you will see the “QR Code”

3. Please open your mobile APP “XMeye Pro”

（1）Click the Scan icon on the top left corner

（2）Scan the “CAPTCHA” on the TV monitor, then you will get a code from the mobile phone APP or from your email, and enter the code into “CAPTCHA”, so you will be able to reset the password on the Monitor connected to DVR

.

B: Add Device on PC Client Software (VMS）?

VMS download link:

For Windows （2023 newest version）

https://download.xm030.cn/d/MDAwMDE0OTM=

For Mac ( 2022 version)

https://download.xm030.cn/d/MDAwMDA2NDA=

1. Download PC Client “VMS” and installed

2. Login with the default User Name and Password. Click “SIGN IN”.

Default User name is: admin

Default Password is: admin

3. Navigate to “Device Manager”–>”Manual Add”

4. Login Type: Cloud ID Device Name:

Name Your Device as you like

Cloud ID : Device Serial Number. We need to go to the TV Monitor connected to the NVR , and find out the information on TV Monitor UI, then right click the mouse to navigate to the path of “Main Menu–>Advanced–>Version” to find out the information “serial number”

User Name and password: Input the user name and password that you created for the NVR , and we also need to find this from the Monitor UI.

.

5. Navigate to “Live View”, Click on the device name(serial number), then select “Open All By Sub Stream”

.

C:  How to Sign up account on Mobile APP (XMEye Pro) ?

Please follow these instructions to sign up for an account via your mobile number.

1. Click on Sign Up

2. Sign Up by email or Select Mobile Number

3. Select the correct country code +1, input your mobile number and click on “Get code”

4. A code will be sent to the mobile phone number, input the verification code and continue.

.

D:  Add Device on Mobile Phone APP (XMEye Pro)?

Steps:

–>1. Please connect the NVR/DVR box to your Router via Network Cable; (Some customers think it can support WIFI connection, while wired systems only support wired router connection, and have to be wired to router via ethernet cable)

–>2. Go to Monitor UI Interface, and Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR/DVR is online (Please skip step3),

–>3. If the cloud status shows “Probing DNS”, Please Navigate to “Main Menu > Network > Check the icon of “Enable DHCP”–>Apply;

–>Reboot the DVR by unplugging the power adapter and re-plug it, then double-check the cloud status ( only cloud status shows )

–>4. Go to your TV Monitor, navigate to “Main Menu–>Advanced–>Version”–> You will see the serial number.

The QR code contains Serial number info. We need this information after we add the device to mobile phone APP

–>5. Open the mobile APP “XMeye Pro” and register an account by your email first

–>6. Click”+” to add device–>Choose “NVR”

Device Serial Number: Click the “Scan” icon to Scan QR Code On the NVR UI Interface (Main Menu–Advanced–Version), (QR code contains username and password)

No need to input the username and password manually.

And click “OK”, and go back to the Device page on App,and you will see the device shows status:online ,

E:  How to enable Alarm Notifications on APP XMEye Pro?

1.Make the Alarm setting is already set on Monitor UI Interface

2. Please right-click mouse and navigate to “Main Menu–> Alarm–>Motion Detect/Human Detect/Face Detect–> Enable “Mobile Reported”–>click “OK”

(Default Setting is for Channel 1, Please select “All” channels.)

2.Open “XMeye Pro” mobile App, and navigate to “Event–>Device (the one you named)–>Enable “Allow Notifications”

.

F:  Configure Offline Camera or Add a New Camera?

—>1. After connect the camera to NVR via network cable, if the camera power on properly, the camera’s indicator light should be blinking.(see picture attached)

.

When you cover the camera’s photocell or put the camera in dark place, the infrared LED should turn on red color.

—>2. If camera powered on properly please follow below instructions.

1.Right-click mouse navigate to “Quick Setup(or Channel Set) –>Cancel

2. In the second box, if any camera status is offline or not connected, please select it and click ”Delete” first

3. Click “Search”, can you see new IP address showed on the topper box?

4. Select the IP address in topper box and click Network–>Auto Assigned–>OK

5. If auto assigned successfully, please click “Add” to add the camera.

.

.

G:  No Video Display on TV Monitor Or Blank Screen?

My UI Interface shows “No signal” or “Black Screen” ？

We need to divert this issue into two situations:

1.NVR Indicator light is on:

(1) Cause: The camera system’s video output resolution is 1080P. If your TV monitor resolution is below 1080P, this issue will occur.

Steps:

Please right-click and hold your mouse for over 10 seconds to see if the system can reboot or not. Or, please try to connect the system to another TV monitor with a higher resolution (above 1080P)

.

(2) Cause: The hard disk drive inside of the DVR box is broken, and use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is having an issue, and needs a replacement, plz contact email love@hiseeu.com for replacement HDD

After steps, if the thing still cann’t be resolved, which means the NVR box is broken, plz contact email love@hiseeu.com for replacement NVR box if their warranty is still 1 year

.

2.NVR Indicator light is off:

(1) Cause: The power adapter 52V 2.5 A connected to the NVR box is broken

Step: Use another power supply 52V 2.5 A to power on the NVR unit to have a try ( If you do not have a spare one, can contact us to buy a new one or we send you a new one if your warranty is still under 1 year )

.

(2) Cause: The hard disk drive inside of the NVR box is broken Step: Use the screwdriver to open the NVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the NVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is broken, and needs a HDD replacement, plz contact email love@hiseeu.com for replacement HDD

.

H:Why DVR/NVR can’t record or playback video?

.

If HDD(Hard disk drive) is having issue or something wrong with record setting, the DVR can’t record/playback the video

.

1.Check if the hard drive status is normal or error

Navigate to NVR/DVR Monitor UI Interface: Navigate to “Main Menu–>Advanced–>HDD info”

If status shows “Error” or No hard drive info , which means the hard drive is broken. (need to replace hard dirve)

2.Check the record plan is set up for 24/7 continuous recording

Navigate to “Main Menu–>Record Conf”

Channel : select “All”

Period: “00:00-24:00”

Select “Regular”

3. Please make sure the HDD was set up to “Overwrite”. (if it was set to “stop”, the system would stop recording when the storage is full)

Navigate to “Main Menu–>General–>Storage Full”

Add Device on Guard Station PC Client Software

Add device to “Guard Station” Download link: https://www.dropbox.com/sh/jeftu4sqwy4y1u8/AAD4PkyEJxg6j4H1n20PxBkZa?dl=0  

.

Please sign up for the mobile APP(Guard Viewer) account and add the device first.

Download and run “Guard Station” on the PC

1) Please Navigate to “Device Management”> “Cloud Device”> Click on “Login”

2) Login with your APP account and password.

3) After Login, the device you added to the APP will list here

Please click on “Control Panel”> “Live View”> Double-Click Camera to load the live view video

Add Cameras to NVR or PoE Switch (Router)

Add Cameras to NVR/ PoE Switch or Router

1. Add camera via NVR PoE Port

• If the camera is connected to NVR PoE port directly, the IP address

range should be modified to “172.16.0.X” (X is between 2 to 255)

Please right-click mouse and navigate to Camera

For brand new camera (password is 123456 by default), NVR will detect

and add camera automatically.

If the camera’s user name or password has been changed, you are required to input the info manually.

Move the mouse to the status icon , you will see the error message. “Offline [incorrect Username to Password]”

Please click on the edit icon to input password manually and click on “OK” to continue.

2.Add Camera to NVR via PoE Switch or Router

NVR will detect the camera under the same WLAN and list IPC here

• Click on plug icon to add the camera. If the camera has default user name: admin, password: 123456.

NVR will add it automatically.

• If the camera’s password has been changed, please click on the setting icon to modify the info.

• In this situation, the camera IP address range should be the same as NVR’s IP range

(You can check NVR IP by navigating to Network>Basic> TCP/IP). If not, please contact the technician to modify the camera’s IP first.

Camera Not working

Camera not working?

1.(Port issue) Insert the camera to another port of the NVR to have a try, and wait at least 5 minutes

2. (Camera issue) Make sure if the camera infrared light will turn on red or not in the night time

3. Also plz right click your mouse to “Menu-Camera”, and take a photo of this whole page and send it to us

（Check how many cameras are discovered）

Also go back to the home screen and Check connection status, to see if it shows” Network disconnected” or “incorrect user name and password”

Device Offline on APP or NVR?

Device Offline on APP or NVR?

If the device shows offline on mobile phone app  “Guard Viewer” , we need to make sure the NVR is connected to network perfectly or not

Go next to your Monitor that connected to NVR, and check out the network status

first navigate to this path first : “Menu–Network–Basic–P2P” , also check the device status is online or not,

if it shows: network disconnected, plz enable the DHCP in this path ” Menu–Network–Basic-TCP/IP ” and click “Apply” . After that, go back to “P2P” and check if the device status is online or not

Also , please make sure the PPPOE needs to be disabled, plz navigate to “Network–Advanced–PPPoE”

Enable Alarm light on Each Camera?

Enable Alarm light on Each Camera?

.

(Alarm light would only work during the night time when the alarm was triggered)

.

1. Set up the Alarm light First Right-click your mouse to “Menu– VCA — Intrusion Detection/Crossing Line Detection– Triggered Actions” , and draw the rules for the alarm type

After you set up an alarm type (Like”Intrusion Detection”, or “Crossing Line Detection”), Click on “Alarm Linkage”, you will have the option to Enable “Alarm Light” (Spotlight is only Available During the Night)

2. Enable Alarm Light on “Triggered Action– Alarm Light” for each channel, and Click “OK”

Forget NVR Password？

If you forget your current password, please follow the instructions to reset it.

1. In the system login interface, please click on “Enter Password” > “Forgot Password”

2.If you filled in your email address as a reserved email when you set up the system, you can reset the device password via the APP(Guard Viewer) by navigate to “Me–General–Forget Device Password”

3.Scan the above QR code by app and the security code will be sent to your email address.

4. Enter the security code from email to reset the password

Additionally, If you the email doesn’t belong to you, plz contact us at love@hiseeu.com for more support

Add Device to APP(Guard Viewer)

.

Auto add is not suggested. Please tap on “Later” if you see this message box.

.

In this situation, it will Auto Search to discover the NVR device connected to the local network. But once your mobile phone disconnects with LAN WiFi, you will not be able to view it anymore.

Please Add devices in this way

1.  Please Tap on “ Menu” icon> Tap on “Devices”> “Add”,

2. Tap on “Scan”> “OK” to scan the NVR QR code

3.Navigate to “Menu– Network> Basic> P2P”

• If the Device Status is “Network connected…” , means device is online   and ready for remote view

• If the Device Status is “Offline” , please check the network connection first, if the problem remains, please feel free to contact us at Love@Hiseeu.com   

After you add the device successful, the “Device status” will be “Online”, and your APP account username will display here.   • You can check your APP user name by navigate to “Me”

• If the username doesn’t belong to you, please click on “Delete” and add it again.

4.Add NVR by scanning device QR code and click on “save”

5.   Please Tap on “Menu ” icon, Tap on “Live View” “Add”

6. Select the device and tap on “Start Live View”

Human Tracking/Detect for Model PK-4YHD985-CT ?

1.To enable human tracking , Set preset point “21”. Here is the video link for your reference: https://www.amazon.com/live/video/07adae4ec34a47618bd754cc6c1f8966?ref_=dp_vse_ibvc1

2.To enable human detection, plz go to this path “Menu–Alarm-Motion” , and choose the camera you want, to enable it

(This doesn’t support customize area)

No Video on TV Monitor or blank Screen?

.

The camera system video output resolution is 1080P, if your TV monitor resolution below that will occur this issue.

.

If possible, could you please try to connect the system to another TV monitor with a higher resolution(above 1080P).

Or, please hold your mouse wheel over 10seconds to see if the system can reboot or not.

If not, plz contact us for further support

How to share Device to others via APP Guard Viewer?

.

One device linked to One User ONLY. The NVR system ONLY can be controlled by one authorized account, who can share the device with others in order to prevent attacking or hacking.

For admin user, please follow the instructions to share the device with others:

.

1.Type on “Menu Icon ” and navigate to “Devices”

.

2.Tape on “… ” > “Share”, You can select a single channel to share or select the entire NVR system to share

(1) Share device by typing in the user name you wanted to share with and selecting function as needed.

• The other user needs to register a Guard Viewer APP account and provide the user name for sharing.

• After that, when this user login the APP will find the device by navigate to “Devices”

(2) Share device by generate a QR code

• Create a sharing password and set the valid period

• Click “Generate”, your APP will generate a QR code

• Other users can use the APP to add the device by scanning the QR code you sent

Download the mobile APP and Sign up for an Account

.

1. Download and install the app.

Please scan the QR code to download the free APP “Guard Viewer”

You also can visit the Apple Store or the Google Play Store to download the Guard Viewer app for iOS or Android devices. Alter installation, tap the icon to launch the app.

2.Register an account and login

For first time use, please create a new account and add the following steps:

Please tap Sign up and follow the on-screen prompt to register an account by email.

<p>The post Hisseu PoE Camera System User Guide v1 first appeared on NVR IPCAMERA SECURITY.</p>

InVid Tech is here to help you succeed, and as a company, we pride ourselves on the level of personal service we offer. We have an experienced team based in the United States, including Sales, Customers Service, Marketing & Tech Support. Additionally, there is support for Latin American Countries.

Steps to Change Secure Series Camera Compression to H.264

The below steps are needed in order to connect your camera to the Secure 4ch NVR attached with your order.  Please log into camera first, default username is “admin” and default password are “1234567u”, from there it will prompt you to change, please do so and follow below steps.  If you do not do this first, the camera will not connect to the NVR.

SEC-BODYTEMPCAM1 Camera Configuration Guide

**Please Note:  Cameras Default IP address is 192.168.1.121.  IP Utility can be downloaded off our website here

• Log into the cameras web interface on Internet Explorer (IE), default username is “admin” and default password are “1234567u”. Make sure to download the new plugin. 

Note: close ALL browser tabs while installing the plugin.

• Parameter Configuration (Configuration/Human Thermometer/Parameter Configure)

◦ Enable face detection

◦ Draw the area according to the real scenario, there is a maximum of 8 areas supported. We usually use one detection area to cover where people could potentially appear in, recommended distance is 9 to 16 feet (3-5 meters) for capturing.

• Leave the Display Trace Info at “Mode 1”

• Show Detection Area, can turn On or Off

• For Confidence Coefficient, we suggest keeping the default value (Mid). It’s for the face matching level with the built-in algorithm.

• Area ID is for the selected areas if you choose more then one main area, up to 8 totals. We suggest keeping this at one and focusing on the main point of entrance.

• For Face Pixel Minimum and Maximum, we suggest keeping the default value (70/1000). Only faces in this range will be detected.

• There are two different Snapshot Modes: 

◦ Timing: ‘upload interval’ is associated with ‘timing’, camera will upload one picture every 5 seconds (Suggested).

◦ Optical: ‘snapshot count’ is associated with ‘optical’, camera will upload the best face picture in 5 seconds.

• For Upload Image Interval we suggest leaving at 5 seconds (1-10 second range).

• For Yaw Degree, Tilt Degree, Pitch Degree and OSD Overlay Snapshot, we suggest keeping as default.

• FTP Upload Image Matting and FTP Upload Whole Image are if you are using the camera as a standalone device, no CMS or NVR, and wish to save the facial snaps to an FTP.

• Temperature Parameters

• Enable this field and leave all as DEFAULT except LENGTH UNIT and MOUNT DISTANCE

◦ IF YOU SWITCH TO FAHRENHEIT THE FIELDS STILL STAY AS DEFAULT (Except Length/Mount Distance, mentioned above)

◦ DEPENDING ON THE SELECTION OF “LENGTH UNIT” (METERS/FEET), ALL DISTANCE FIELDS WILL BE CONSIDERED IN THOSE UNITS!

[IMPORTANT] Set the mount distance according to the real installation, whose value should be the horizontal distance from the detection area to the camera. 

Hit ‘apply’ to save the settings.

• Face Alarm Linkage

IF SWITCHED TO FAHRENHEIT YOU MUST ADJUST “ALARM TEMPERATURE”, 99.5-100.5F (Default Celsius is 37.30)[

• [IMPORTANT] Thermal Mapping (Configuration/Human Thermometer/Thermal Mapping)

◦ This step is mainly for matching the thermal image with the visible image, which can ensure the measurement accuracy.  The Black Body device (Infrared Calibrator) MUST be in the Field of View of the thermal image.  The thermal image is a FIXED LENS and is a smaller field of view then the standard image.

• There are eight groups of ID, and each group ID contains three points. If using One area, then you do not have to set groups 2-8.

• Pick out three points that you can clearly see in the thermal image, mark them with point1, point2 and point3.

• Find the three locations of the three points in the visible image and mark them with the same point numbers associated with those in thermal image.

◦ Note: Suggested to choose three points far away from one another, so the triangle of can cover 70% of the image.

• Hit ‘apply’ to save the settings.

• Test if the rectangle can correctly surround the face, and perfect it by adjusting the three points.

• Thermal calibration (Configuration/Human Thermometer/Thermal Calibration)

• Install the blackbody properly where the camera can see it (within the thermal image). The blackbody needs to be powered on for at least 20 mins to reach to a stable temperature.

◦ The Infrared Calibrator will ALWAYS display in CELSIUS; the stable temperature is ~40C

• Enable.

• If you turn on ‘Display Area Info’, the blackbody (Infrared Calibrator) will also be shown with temperature on thermal image.

◦ Draw box around your calibrator

• Target Temperature: If using Celsius leave as 40C, if using Fahrenheit change to 104F (Default)

• For Distance, put the real installation distance between the camera and Black Body (Infrared Calibrator). No more then 9-16 feet (3-5 meters).  Distance is in Meters or Feet, depending what you selected under the Parameter Config menu.

• Keep the ‘Emission Rate’ as the default value.

• Hit ‘apply’ to save the settings.

InVidTech Secure Series Setup Guide v1

Also Read : How To Setup O-KAM Pro camera

SEC BODYTEMPCAM1 camera run off of POE output?

Yes it is, safe.

What are the minimum specs required to handle SEC-BODYTEMPCAM1?

For a single camera: i7 processing, at least 8GB of RAM.

From where is the temperature being scanned?

From a point in the middle of the forehead, the temperature is scanned, above the nose and in-between the eyes. If the camera captures a profile image it is using the skin around the earhole for temperature.  It is important to note that what is being scanned is skin temperature and not core temperature.

Should people be screened prior to entry?

The camera needs to be set within a controlled environment and cannot be installed outside. The calibrator isn’t weatherproof (IP66) and airflow, whether inside or out, could throw off the camera’s calibration.

If you need to screen people before entering the building, you would need to set up an enclosed tent to scan individuals. The camera can operate in both extreme heat and cold as long as no airflow would skew the results. If an individual is outside for an extended period, in the intense heat or cold without the opportunity to reregulate their temperature, the results might be slightly off, its recommended to wait 20-30 seconds before reading.

Need to wait when coming from outside for accurate reading?

Most of the time, there will not be any accuracy issues when getting scanned. If you have been out in the extreme heat or cold for an extended time you may want someone to wait roughly 30 seconds for their body to adjust to the environment. The camera is taking the skin temperature, which the human body keeps in check very efficiently.

What is your advice for poorly controlled environments?

If you are going to invest in the product, you will also need to invest in creating a controlled environment. If the environment is not controlled, you will not have accuracy. 

What effects an individuals’ temperature?

An individuals’ temperature will not read higher based on wearing a darker colored cap or clothing. The temperature scanned is the skin. The camera is using the face detection analytic to detect a human face then apply the algorithm built into the camera to display a temperature that is read from the epidermis of the forehead, or if it is a profile picture captured, the skin around the earhole is used.

If you’re wearing a mask, glasses, hood, hat, or all combined, if those two focal points aren’t blocked, then the camera can give a temperature reading.

Depending on the type of hat, for example, a forwards facing baseball cap pulled down entirely over the forehead can cause an individual not to be scanned. Another factor that could affect the scan is how the camera is mounted. The cameras must not be mounted higher than 8-feet. If the camera is wall-mounted and facing on a downward angle where a hat or hardhat is blocking the forehead, a solution would be to mount the cameras on a tripod to get a more direct shot.

Please watch the scenario video here for more info on this.

As for individuals who have been out in the extreme heat or cold for an extended time you may want to wait about 30 seconds for their body to adjust to the environment. The camera is taking the skin temperature, which the human body keeps in check very efficiently.

Two real-life examples of cold and hot temperatures:

In New York, the temperatures were averaging 45 degrees, and we had someone whose drive into work took about 20 minutes. While driving, they had the window rolled down and the air continually blowing into their face. They would walk from their car to the office and could feel their skin was cold. When walking into the office, they would get scanned, and their temperature would be between 96.9 and 97 Degrees. After waiting for about 60 seconds, they would rescan, and their temperature would average the mid 97 degrees.

In Arizona, where the temperature was over 100 degrees, we found that when someone was outside for a while, a cooling down about 20-30 seconds was necessary. Initially, their temperature registered at about 102, but after 20 seconds, it stabilized and showed their baseline temperature.

Something to keep in mind is that everyone is different. Two people who are excessively overheated may vary slightly in how fast their bodies regulated their temperature. One person might take about 10 seconds, while another person might take about 45 seconds. We are finding that the average is about 20-30 seconds for someone to regulate back to their baseline skin temperature.

Does the subject have to face the camera?

The subjects face must hit the 7% FOV (Field of View) mark of the camera to get an accurate reading. It is looking for two measurement points. The first point is in the middle of the forehead, roughly the area in-between the two eyes, near the nose, and if it captures a profile image, it is looking for the skin around the ear hole. The person has to be walking into the view of the camera and not away.

What is the ETA on the Fahrenheit firmware fix for US sites?

The firmware is currently available, giving the option for Fahrenheit or Celsius. The product leaves our warehouse with this latest firmware update, and the product comes defaulted to Fahrenheit & Distance comes defaulted to Feet with the option for metric units. 

What VMS’s are supported?

As of today 4/29/20, we know Axxon and EXACT are working on an integration. Other companies that have reached out but are not 100% confirmed yet. The SDK is available upon request but each is responsible for their integration. 

Without an NVR, will images be stored?

No. The camera will not store any images. 

Will the camera do face recognition without an NVR or computer?

The camera only does face detection. The CMS is what handles Facial Recognition if you aren’t running the CMS, face images will not be saved.

Will the camera track a person?

Tracking is based on facial detection. As soon as the 7% mark is met (7% is the required amount to get a temperature), it will read the face detection analytic and then apply the algorithm for the temperature display.  

Where are these cameras made?

The cameras are manufactured in China but are not affiliated with and are not OEM made products from Hikvision or Dahua. 

Can the camera just be connected to a LAN that has the NVR on it?

Yes, it can be stand alone.

What is the accuracy of the camera?

The accuracy of the camera is 0.54 Degrees Fahrenheit / 0.3 Degrees Celsius.   

Is this camera FDA approved for taking Body Temperature readings?

We are currently in the process of working on our 510k Certificate approval. 

Will the camera pick up the temp of a person who is walking away?

No. it is not designed to work this way.  Depending on the angle, it might be able to capture a profile and on occasion provide a temperature. 

Is there a max mounting height from the floor?

Yes, you may not exceed 8 feet from the floor when installing on a wall or ceiling mount.

How do you calibrate the calibrator?

Let the calibrator run for about 15-20 minutes. On the back panel of the calibrator, you will see a display. The display will be in Celsius regardless of the settings in the camera and CMS. Once the screen hits the 40-40.2 degrees, the unit has been calibrated. 

Can you set the camera and calibrator to shoot through a glass door?

 No, the camera and calibrator must be in sight of one another and cannot see through a glass window or door. There can be no glass between the devices and the subject. 

How far away does the calibrator need to be from the camera?

The camera and calibrator must be in view of each other and must not exceed 16 Feet. The recommended distance is 7-16ft. and the calibrator must be in the field of view of the THERMAL image

Does each camera require its own calibrator?

Yes, each camera requires its own calibrator. You cannot use two cameras with a single calibrator. The temperatures will not be accurate. 

Can you connect the CMS to a customer’s network?

Yes, the CMS can be connected to a customer’s pc and also run on a pc that is not on the network.

What does CMS stand for?

Central Monitoring Software

Is the CMS included with the purchase of camera & calibration device?

Yes, there is a free download that is available on our website. There is no charge. You can find it here

How many users can log into the CMS simultaneously?

The CMS (Central Management System) is stand-alone. You can install it on multiple computers, but there is a max of 10-user connections for each camera.  

CMS (Central Management Software) for PC

CMS for PC

This is the free CMS (Central Management Software) for the Secure Series for those using a PC. It will work with Secure Series Products. 

New in this Version:
.

Version V1.8.163.0.0.51.0_build 20240206

User Name: admin
Password: 1234567u

Download Secure CMS Here

Download AD (Active Directory) Instructions Here

IP Tool Utility for PC

This is the free IP utility for the Secure Series for those using a PC. It is used to find IP Cameras on the network and change the IP info (IP Address, Sub-Net, Default Gateway) of those devices. Version v1.9.9

Supported Devices: Secure NVRs, Secure IPCs

Download IP Tool Here

If you are using a computer, will it record video without an NVR?

No, the closest workaround is to add the camera to the CMS. The CMS saves snapshots based on facial recognition. Please keep in mind that if the CMS doesn’t see specific points of a face to realize its a face (such as if the person is partially covered), you may still get a temperature read, but the face snap may not save. The CMS is only saving snapshots, not video.

How to use a cloud feature in the NVR menu?

The cloud feature will be implemented in the future. Once it is fully functional, we will have additional information posted!

How many hours of video can be stored on the NVR?

That will depend on the size of the drive you put in the unit and the number of cameras you have installed. The standard 4-channel unit can house a single hard drive bay, and can use drives ranging from 1-10 Terabytes. 

Can the NVR do the job of counting and temperature notification?

No.

Will camera send notifications automatically without an NVR?

If the camera is networked, email notifications can be sent out, even without an NVR. This will include a snapshot with the temperature for individuals who are above the threshold set. The camera also has two alarm outputs that can be utilized.

To use the app, InVid LIVE CMS, the camera would need to be added to the CMS, and the CMS would have to be kept open and running on a PC. If a temperature over the threshold is registered, it will send a push notification to the app.

Is the NVR required for sending email alerts?

No, the camera can send out email alerts. The 4/8/16 Channel NVR does not have the ability to send out email alerts while the 32 channel unit does, for over temperatures.

What type of notifications are triggered by high temp?

You can have an email notification with a snapshot of the individual and temperature range and also the option of one or two sirens if the temperature is above the threshold. 

Are there any onboard relays that could be triggered to send an alert

Yes, the camera has 2-alarm outputs. Power is needed, 12/24 volt AC/DC. Settings within the camera can be configured to trigger an alert when a temperature is over the threshold. 

Can the system send email and text alarms?

The system can send emails, it includes the picture of the scene with the temperature reading. Currently, there are no text alarms, but it is something we are looking at trying to implement.

Audible alarm once it detects a high temp?

The camera has two notification functions. The first is an email notification. The second is an alarm output trigger. The CMS that links to the camera does have an audible alarm if your computer is set up for sound. 

What is the warranty on the Secure Series products?

Camera: 1-Year

Calibrator: 1-Year

NVRs: 2-Year on Unit & 2-Years on Hard Drives

.

<p>The post InVidTech Secure Series Setup Guide v1 first appeared on NVR IPCAMERA SECURITY.</p>

ATTENTION: Prior to purchasing and installing an accessory antenna, read the product specifications of your receiver to determine if your receiver has a weatherproof housing. Installing your weatherproof receiver outdoors provides a better line-of-sight between the receiver and the camera, increasing the strength of the wireless signal. See your product specifications to determine the weatherproof rating of your receiver.

The Directional Wireless Panel Antenna and the Omni-Directional Antenna are used to extend the range of one or multiple wireless or wire-free cameras.

Directional Wireless Panel Antenna (ACCANTD9)

Omni-Directional Antenna (ACCANTO8)

Use the 2.4GHz Directional Wireless Panel Antenna (ACCANTD9) to focus a wireless signal onto one specific wireless device (camera or receiver) to increase the range of transmission. A clear line-of-sight between the antenna and the wireless device needing range extension is required.

Use the 2.4GHz Omni-Directional Antenna (ACCANTO8) to enhance the signal of one or multiple cameras that are paired to a single or dual antenna receiver. You may also use two Omni-Directional Antennas to extend the range of all cameras paired to a dual antenna receiver.

REQUIREMENT: To connect the antenna directly to the camera or receiver, the device must have a removable SMA type antenna. Visit www.lorextechnology.com/compatibility to ensure the antenna is compatible with your camera or receiver model.

Lorex Wireless Cameras and Monitors guide 2024

Also Read  : Lorex Camera Troubleshooting

Recommended Antenna Installation Methods

Your antenna needs will vary depending on the setup of your camera system, the number of cameras that require range extension, and the number of channels on your wireless receiver. Review the scenarios below to ensure you have the correct antenna and installation method to meet your needs.

Click a setup scenario to see the recommended installation method:

Combining Accessory Antennas

If you have installed your accessory antenna according to the recommended installation methods and would like to enhance wireless signal strength even further, you may add an additional Directional Wireless Panel Antenna (ACCANTD9) directly to a camera. The additional Directional Wireless Panel Antenna can be used with a Directional Wireless Panel Antenna or with an Omni-Directional Antenna attached to the receiver.

Click an antenna combination to see recommended installation methods:

Scenario 1: Extend the range of one camera paired to a single antenna receiver

To extend the range of one camera connected to a single channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9).

The Directional Wireless Panel Antenna can be connected in two configurations.

Configuration 1. Connect the antenna directly to the camera

Configuration 2. Connect the antenna directly to the wireless receiver

REQUIREMENT: The antenna connects using an SMA cable and replaces the existing antenna on either the camera or wireless receiver. Check www.lorextechnology.com/compatibility to determine if your product is compatible with the antennas.

Scenario 2: Extend the range of one camera paired to a dual antenna receiver

To extend the range of one camera connected to a multi-channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9). Connect the Directional Wireless Panel Antenna directly to the camera.

Scenario 3: Extend the range of select cameras paired to a dual antenna receiver

To extend the range of select cameras on a multi-channel receiver, use the Omni-Directional Antenna (ACCANTO8).

Connect the Omni-Directional Antenna to one of the antenna ports on the wireless receiver.

REMINDER: Each antenna port on a dual antenna receiver is associated with specific camera channels. One antenna communicates with odd numbered channels (1, 3, and 5), while the other antenna communicates with even numbered channels (2, 4, and 6). See the table below for dual antenna channel configurations.

If you connect the Omni-Directional Antenna to an antenna port and your wireless signal does not improve, try switching the Omni-Directional Antenna to the other antenna port or pairing your camera to a different camera channel.

Scenario 4: Extend the range of all cameras paired to a dual antenna receiver

To extend the range of all cameras on a dual antenna receiver, connect an Omni-Directional Antenna (ACCANTO8) to each antenna port on the receiver.

IMPORTANT: Two Omni-Directional Antennas are required to accommodate this setup.

Combination 1: Combine two Directional Wireless Panel Antennas

If you are using a Directional Wireless Panel Antenna (ACCANTD9) to enhance the signal of a single camera with a single channel receiver, you can use an additional Directional Wireless Panel Antenna to further enhance the wireless signal.

Connect one Directional Wireless Panel Antenna directly to the camera and one Directional Wireless Panel Antenna directly to the wireless receiver. To maximize signal strength, it is recommended to aim the two antennas directly at each other with a clear line-of-sight.

Combination 2: Combine a Directional Wireless Panel Antenna with an Omni-Directional Antenna

If you are using an Omni-Directional Antenna (ACCANTO8) to enhance the signal of multiple cameras, you can further enhance the signal of a specific camera by connecting a Directional Wireless Panel Antenna (ACCANTD9) directly to the camera.

A clear line-of-sight between the Directional Wireless Panel Antenna and the Omni-Directional Antenna is recommended to maximize signal strength.

Lorex SD Pro App: Changing / resetting the password

If the password for the Lorex SD Pro app to view the Wireless Home Monitor is lost or forgotten it will need to be reset.

To reset the Lorex SD Pro app password:

1.Ensure that your Wireless Home Monitor is connected to a network router using the included Ethernet cable.

2.On the Wireless Home Monitor tap the Menu icon ().

3.Use the joystick to select Settings > Network > Reset Password.

4.Select Yes to confirm.

5.Tap the Menu icon () repeatedly until all the menus are closed.

6.Launch the SD Pro app and enter the default password. Refer to your user manual for your default password. You will be prompted to create a new password.

Lorex SD Pro App: Setting up Wireless Home Monitor remote access

You can access and view wireless cameras from a Wireless Home Monitor system using an iPhone, iPad, or Android smartphone or tablet using the Lorex SD Pro app. It is available at the App Store or Google Play Store.

Prerequisites:

To set up the mobile application:

LW2700 Wireless Home Monitor: Included cables and accessories

LW2700 Series Wireless Home Monitors support wireless cameras using a wireless signal. They do not have an internal battery and require a connection to a power source. Refer to your user manual for model specific information on cables and accessories. Click here for downloads and documentation for your product.

Most wireless home monitors include the following cable connections and accessories when purchased:

Network: Wireless camera Internet requirements

Standard wireless cameras that connect to a DVR / NVR, do not need access to the Internet to function. Stand-alone IP cameras do not require an Internet connection for basic functions, but an Internet connection is required for full functionality.

Security Cameras: Understanding Field of View (FOV)

Field of View (FOV) is the maximum observable area that is seen at any given moment through an optical device such as a camera lens. The coverage of the area can be measured using the horizontal and vertical distances to find the diagonal of the area in degrees. Mathematically, the FOV is calculated using the horizontal dimension of the sensor (h) and the Focal Length (F).

You can find the camera’s Field of View details in the Specifications sheet. Click here for additional support content including security camera documentation.

The Camera Lens, Sensor and Focal Length

Focal length (F) is the distance between the center of a lens and its sensor. The size of the lens is the aperture size.

These factors affect field of view. A narrower focal length captures more of the scene and displays a larger field of view. A wider focal length magnifies a scene and decreases the field of view. The higher the focal length value the lower the FOV.

Types of Camera Lenses

Fixed: a fixed camera focal length provides an Angular FOV which is permanently set and cannot be adjusted by the user. Varifocal: the camera focal length can be manually adjusted by the user. Generally, this is done manually with screws or dials. At Lorex we have motorized varifocal cameras that allow you to digitally zoom using your phone or NVR without losing details. These lenses provide flexibility and customization for your camera image needs.

The importance of Field of View

A wide angle lens or smaller lenses produce a greater field of view and captures more objects in a scene enhancing your ability to cover larger and wider areas such as foyers, parking lots or warehouses.

A narrow angle lens or larger lenses produce a smaller field of view; capturing a limited area, but the camera quality image improves in detail. These are designed to monitor a specific object, such as cash registers, entrances/exits, hallways or objects of value.

How to Calculate the FOV

To calculate the FOV requires the sensor size and the focal length of the lens: h = Sensor Size F = Focal Length of the Lens

FOV is represented by this equation: FOV = 2tan-1(h) / 2F

Example: h = 4.7mm F = 6mm FOV = 2tan-1(h) / 2F = 2tan-1(4.7)(12) = 2tan-1(0.39) = 2(21.4°) = 42.8°

W482CAD – 2K Wi-Fi Camera : Frequently Asked Questions

The following FAQ article answers many of the general questions about the 2K Wi-Fi Camera with Smart Deterrence (W482CAD). Where applicable, the FAQ includes links to articles where you may find more information.

.

Where do I place my Lorex 2K Wi-Fi Camera?

.

How should I position my Lorex 2K Wi-Fi camera?

When mounting the camera on a wall, make sure of the following:

 Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

.

How do I enable motion detection and person detection?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap  icon to enable Motion Detection.

Note: If motion detection is disabled, general/person/vehicle detection will automatically disable and you will not receive any motion detection notifications in the Lorex App.

.

How do I customize Motion Zones™?

Motion Zones™ allows you to customize your device’s motion detection region. Motion Zones™ screen consists of the following settings:

To set Motion Zones™

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap Motion Zones™.

 For full instructions on how to set customized Motion Zones™, see Configuring Motion Zones™.

.

Why am I receiving so many notifications?

There are a few ways you can lower the number of notifications you are getting.

.

How do I enable Color Night Vision?

1.Lauch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap  icon to disable Auto Night Vision.
Note: Disabling Auto Night Vision will force the camera into Color Night Vision mode. Recommended in low-light conditions.

.

How to activate Two-Step Verification?

1.Launch the Lorex App.

2.Tap Settings.

3.Tap Account Settings.

4.Tap Two-Step Verification.

5.Tapicon to enable Two-Step Verification.

For detailed setup instructions, see Two-Step Verification Setup.

.

How to optimize video quality?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Video Settings.

4.Tap  icon to enable HDR (High Dynamic Range).

Note: Enabling HDR optimizes video picture in high-contrast conditions such as under-lit and over-lit areas.
By default, the video quality is set to High (2x1080p HD).

.

What is Home & Away™?

Lorex App can automatically use your location to manage your notifications when you are at home or away. The app will notify you when you are inside/outside of your set home perimeter.

To start using this feature, navigate to your mobile device settings and enable Location services for Lorex App.

For detailed setup instructions, see Configuring Home & Away™.

.

How do I activate the LED deterrence light when motion is detected?

1.Lauch Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Deterrence Light Brightness.

4.Tap  icon to enable camera’s deterrence light whenever motion or person is detected.

.

How do I remove the 2K Wi-Fi Camera from my account?

1.Launch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Remove Device.

.

How to permanently delete data of 2K Wi-Fi Camera?

Refer to Formatting Device Storage for more information.

.

Does my device support WPA2 or WPA3?

Your device supports Wi-Fi Protected Access 2 (WPA2) which is the industry standard security protocol for Wi-Fi networks. WPA2 offers security against unauthorized access and data interception and is supported by most Wi-Fi routers including those that support both WPA2 and WPA3. It employs Advanced Encryption Standard (AES), an encryption mechanism, which secures communication between your camera and Wi-Fi network to keep transmitted data confidential. For information on which devices support WPA2 and which devices support WPA3, please refer to “WPA2 and WPA3 Supportive Devices.”

.

What are the compatible SD cards?

Refer to Compatible SD Cards and Storage Sizes for more information.

.

What devices are compatible with the 2K Wi-Fi camera?

Refer to Product Compatibility Chart for more information.

W482CAD – 2K Wi-Fi Camera : Installation

This article provides instructions to install your Lorex 2K Wi-Fi camera with Smart Deterrence (W482CAD).

.

What is included in the box?

The above contents are based on one camera.

.

How to connect with Lorex App

3.Open the Lorex App app and create an account or login with your credentials.

4.Tap  icon to add a new device, then follow the in-app instructions to complete the device setup.

For full instructions on Lorex App setup, see Connecting with Lorex App.

.

How to mount 2K Wi-Fi Camera to the wall

.

How to mount 2K Wi-Fi Camera to the ceiling

Wi-Fi Security Cameras – How to Read a MicroSD card

To view the contents of a MicroSD card on a laptop or computer, follow these steps:

a. Select the day to play back:

b. Click on the available folder:

c. Within the folder, click either the day folder (Video files) or the jpg folder (Snapshots):

d. Click to select a video time from 00 – 23 hours:

6.Click the MP4 video file to view the video. 

Wireless Home Monitor: Audio not working

If the audio is not working on your Wireless Home Monitor:

• Ensure that the protective film is removed from the camera lens.

• Ensure that the monitor volume is not muted. A mute icon () will be visible on the screen if the volume has been muted.

• Turn the monitor volume up using the volume buttons on the side of the unit. Location will vary by model. For exact location of volume buttons for your model, refer to your user manual. Click here for downloads and documentation for your product.

• The camera must be in Full Screen mode for audio. Tap the Channel Select icon () to switch between channels in Full Screen mode. Audio is disabled in Quad mode.

If audio is not working after increasing the volume and viewing in Full Screen mode, restore the system to default settings.

To restore your monitor to default settings:

CAUTION: Restoring to default settings will erase any setting input on the monitor. Your monitor will need to be reconfigured.

1.On the monitor tap the Menu icon ().

2.Use the joystick to select Settings > Default Settings.

3.Select Yes.

.

<p>The post Lorex Wireless Cameras and Monitors guide 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Overview

The IMOU Ranger 2C IP camera does not support HomeKit but it DOES support ONVIF and RTSP, which is excellent. When using the IMOU app, the camera supports some basic motion detection and pan/tilt, but none of that functionality seem to be supported via ONVIF, which is strange because the IMOU LOOC cameras at least extend their motion detection abilities to ONVIF. I wonder why they dropped that with the Ranger?

IMOU Ranger IP Camera How To Use

Read More : Cync Smart Cameras User Guide

Unboxing

The camera is accompanied by a USB power cable, wall adapter and some strange plastic part with two holes in it. I have no idea what it is for.

Setup

If you haven’t already done so, you need to install the IMOU Life app.

Annoyingly, you’ll have to create an account before you can set up your camera. Everyone expects that these days, but it’s a dumb requirement and something that Streamie absolutely avoids.

After you’re signed in, choose the option to scan a QR code.

On the bottom of the camera, if you have 20-20 vision, you’ll see the QR code and the recovery code which is the default password for the device. Point your phone at the QR code to continue.

And don’t forget to actually plug in your new camera.

While I always rag on cameras that require switching wifi networks to perform the initial setup, the IMOU setup process at least does all of the work for you.

Next up, give the app your wifi network name and password.

And then wait patiently. If you happen to block internet access for untrusted devices, you’ll have to disable that firewall rule now, while the camera “phones home” for what I’m certain are entirely legitimate and necessary reasons….

Next up, choose your region and a date format. I’d imagine the app could figure this out automatically, but whatever.

And then the app wants you to choose where you’re placing this camera, for reasons….

And then FINALLY, the camera is set up in the app.

And you can tap on it to stream it. Yay.

In the next section we’ll get this IMOU Ranger 2C camera set up in Streamie and to do that we need the password, which you can find in the app. Tap on the button to configure the newly added camera and then tap on this thing at the top.

Then tap on “Device Label”.

On this screen you can see your recovery code which is also the default device password that we’ll need to give to Streamie.

Also, if you go to Device Firmware Version screen, there’s probably a firmware update waiting for you, which can’t hurt to apply now, since you’ll probably never think to do it later.

RTSP and ONVIF functionality is enabled by default so we don’t need to do anything but have that recovery password handy.

.

Camera FAQ

1.How to select memory card capacity?

(1). For FHD/1080p/2MP resolution cameras:

a 32GB memory card can be used for 3 days;

a 64GB memory card can be used for 6 days;

a 128GB memory card can be used for 12 days;

a 256GB memory card can be used for 24 days;

(2). For QHD/2.5K/4MP resolution cameras:

a 32GB memory card can be used for 1.5 days;

a 64GB memory card can be used for 3 days;

a 128GB memory card can be used for 6 days;

a 256GB memory card can be used for 12 days;

(3). When the storage is full, historical video records will be replaced by new videos in chronological order automatically.

2.How to set up your camera?

If you want to set up your camera, please follow the steps as below.
Please note: ensure the distance between the camera, mobile phone and the router is within 30cm during the configuration procedure.
1. Tap “+” to scan the QR code of the label and tap “Next”.
2. Connect the phone to the camera’s hotspot signal named that begins with “DAP”.
3. Tap the WiFi that you want to connect to.
4. Enter WiFi password and tap Next.
5. Wait for the connection.
6. Added successfully.

3.How to share your cameras with others？

1. Reach to Share Device on the home page.
2. Tap ‘+’ and input the email address you want to share the device with. Or you can share by QR code.
3. Special permissions for the shared user.

4.How to view history record?

If you want to view history records from Imou APP, please follow the steps below.
In the preview interface.
1. Play the live video and tap the “Event History Timeline”.
2. Select cloud storage or SD card storage to view the recording
3. Tap to view all recordings
In the home interface.
1. Tap “··” on the device menu.
2. Tap “All videos” to view all recordings.

5.How can I stream Imou camera through Amazon Echo Show / Google Nest Hub?

You can follow the configuration wizard of Google Home to configure imou account on Google Home, and the demo will be shown on our official YouTube channel.

6.Where can videos be stored?

Way 1. Use local storage(memory card) as the default mode.
Way 2. If the cloud storage service is enabled, enable the cloud storage and local storage.
Way 3. Use manual recording mode and the recording will be stored in the local storage on the phone or PC.

7.What to do if there is a false alarm from outside the motion detection zone (general activity zone)?

Turn the Human Detection off.

8.Can I set human detection area?

Sorry, you can only set the detection area for motion detection instead of human detection.

9.What to do if there is no alarm after enabling motion detection?

Please try the followings:
1. Turn on the motion detection in the app.
2. Increase the sensitivity in the app.
3. Adjust the dynamic inspection area.
4. Adjust the validity period.
5. Change the memory card property to “read/write”.

10.How do I fix the device IP?

1. Set static IP with SmartPSS and other tools.
2. Bind IP and MAC in router interface.
3. Set the router’s address lease option to “never expire”.

11.What to do if the device initialization (password setting) failed?

1. Keep the device and the phone on the same network.
2. Keep your router online.
3. Switch the DNS server to 8:8:8:8, 8:8:4:4.

12.What to do if the device fails to stream?

1. Check the network connection between the router and the mobile phone, reduce the load of the router, and ensure that the connection is normal.
2. Simplify the networking path of the device and ensure that the device router is connected to the Internet.
3. Check the network configuration and remove the network restrictions of the device.

13.What to do if the device goes on and offline frequently?

1. Check the WiFi signal strength and keep the device and router unobstructed.
2. Reduce the number of access devices and ensure sufficient uplink bandwidth.
3. Adjust equipment distribution to work in different channels.

14.What to do if the night vision mode turns on/off repeatedly?

1. Remove the obstructions in front of the lens.
2. Avoid using in narrow space.

15.What to do if the screen is blurred?

1. Clean the outside of the lens.
2. If the above operation is invalid, return to the factory for maintenance.

16.What to do if the screen is too bright in Night vision / Infrared / Smart Mode?

1. Adjust the distance from the monitoring object.
2. Adjust the angle of the camera.

17.What to do if the screen is too dark in Night vision / Infrared / Smart Mode?

1. Adjust the distance from the monitoring object.
2. Switch to the original adapter.
3. Reset the camera and check the parameter settings with imou life app.

18.What to do if the memory card is not recognized?

1. Clean the golden finger with a rubber.
2. Format the memory card with a PC.
3. Replace the memory card.
4. Access the memory card in the camera using other apps like SmartPSS etc.

19.What to do if the infrared detection is false or not alarming?

1. Avoid installing the device in areas with rapid temperature changes such as air conditioners.
2. Clean the lens and remove obstacles in the field of vision.
3. Adjust the installation angle to avoid direct strong light.

20.What to do if the indicator light is off or solid red?

1. Switch to the original adapter.
2. Make sure the device is not powered off and connected continuously during the upgrade process.
3. If the above operation is invalid, return to the factory for maintenance.

To buy IMOU Protect, please click 👉 here

1.How to reselect devices for Imou Protect plan?

Please make sure you have subscribed to the IMOU Protect plan.
Active your Imou Protect
1. Enter “Me” page.
2. Tap “Imou Protect” to enter Imou Protect Page.
3. Tap the Plan to be activated, then tap “Add devices”.
4. Select devices and tap “OK”.
5. Successfully.
Reselect devices for activated Imou Protect plan
6. Enter Imou Protect Page.
7. Tap the icon (edit) to reselect devices for this activated Imou Protect Plan.
8. The remaining steps are the same as 1. Active my Imou Protect.

2.What’s the difference between cloud storage and Imou Protect?

Imou Protect is a comprehensive service that includes Cloud Storage. Imou Protect delivers a brand new security experience with additional benefits like AI Detection, downloading SD card recordings, sharing devices with more users, security report, and more. 

3.What will be the impact if I don’t subscribe to Imou Protect?

The Imou Protect service is an optional service that does not affect the use of Imou devices without a subscription. By subscribing to Imou Protect service, you will unlock more benefits,  and enjoy more premium experience.

4.How do I upgrade the Imou Protect if I already subscribed to cloud storage?

If you have subscribed to cloud storage service and it is still valid, even if it is a free trial plan, you don’t need extra operations or payment. We will upgrade the cloud storage service to Imou Protect for free. When you log in to Imou APP V5.11.0 or a more advanced version, you will receive a pop-up reminder on the real-time playback page.

Upgrade rules:
3 days cloud storage → Basic Plan, including 3 or 7 days cloud storage
7 days cloud storage → Basic Plan, including 7 days cloud storage
30 days cloud storage → Plus Plan, including 30 days cloud storage

5.Can I try Imou Protect before I subscribe?

A free trial of Imou Protect is available for every newly registered Imou camera. If the camera has already enjoyed the free trial of cloud storage and it has expired, there will be no more free trial opportunities for Imou Protect. 

6.I have several cameras, how do I choose a subscription?

Imou Protect supports subscriptions for a single camera or up to 5 cameras, you can choose the suitable subscription.

7.If the camera is broken, what should I do with the subscribed Imou Protect?

You can transfer the subscription to other cameras or cancel the subscription on Imou APP.

8.If I unbind the camera, what happens to the Imou Protect I have subscribed to?

When unbinding the camera, if the Imou Protect you subscribed to is no longer associated with any camera, you can choose to cancel the subscription on the page. Of course, you can also find the subscription in the Imou APP and cancel it at any time.

9.What is the difference between the AI Detection provided by Imou Protect and the detection function that comes with the camera?

AI Detection provided by Imou Protect gives you the option to only receive alerts when a person, pet, vehicle, and package is detected, even if the cameras with no AI capability. And Imou Protect AI detection provides more detection types than the detection function that comes with the camera. Imou Protect AI detection does not need to update the camera program, it is continuously upgraded with the support of cloud algorithms.

10.If I already subscribe to Imou Protect, how can I enjoy the newly released benefits?

If you already subscribed to Imou Protect and Imou upgrades your current plan features, you will receive the latest benefits for the next cycle at no additional charge. If your current subscription does not meet your needs, you may choose to upgrade to a higher-tier subscription.

11.I want to upgrade the Imou Protect service that I have subscribed, how will I be charged?

After you upgrade the subscription, the auto-renewal of the replaced plan will be canceled. Its remaining service days will be counted as discounts to your initial payment of the current plan. The subsequent subscription will automatically renew at a normal price. You can cancel the renewal at any time.

12.Do all brands of cameras support Imou Protect?

Imou cameras support all benefits of Imou Protect.

13.How to cancel Imou protect plan?

If you need to cancel Imou Protect plan, please follow the steps below.
1. Enter Me page.
2. Tap the option ‘Imou Protect’.
3. Choose the subscription you need to cancel.
4. Confirm to cancel.

.

.

<p>The post IMOU Ranger IP Camera How To Use first appeared on NVR IPCAMERA SECURITY.</p>

The default password for your ONWOTE camera system is 123456 or 1234@abcd. If neither can work, please contact us at support@onwote.com to reset password.

1. Please install SearchoTool on your computer: http://onwote.com/Download#Tools

2. Please connect one of the NVR poe port to your computer directly.

3. Launch Searchool on your computer and search cameras.

4. Check in your camera and click Batch Reset to Reset your camera. Please wait for about 3 minutes until the camera finished resetting.

.

1. Please click the image of the dome camera and click  icon to go to the PTZ setup page.

2. Please click “Add” to add preset, click OK to save this preset. Then move your camera to another position to set the next preset.

3. Please set command for the camera according to the command list below.

Examples:

If you set preset 65, call 65 mean auto cruise from preset 1- preset7.

If you want to stop cruise, please add preset 96 and call 96.

If you set preset 87 and call 87, it means the camera will scan from left to right in low speed.

If you set preset 96 and call 96, the camera will stop cruising.a

ONWOTE Poe NVR Setup Guide

Read More : How to Connect POE NVR via the Onvif Protocol?

.

Step1: Turn off the NVR, unscrew it and remove the cover.

Step2: Unscrew the screws on the bottom of the NVR.

Step3: Unplug the 2 cable from the Hard drive

1. Connect the switches one by one, then connect the poe switch and NVR with the same router.

2. Change the cameras IP to the same segment with your router/enable DHCP of your cameras.

Please download the software SearTool and install it on your computer (connected to the same router):

http://onwote.com/Download#Tools

Please use SearchTool to detect the camera. Then check in the cameras and click Batch Edit IP. Click DHCP to enable DHCP of your camera or choose IP Batch Manually Setting to change the camera’s IP address to the same segment with your router manually.

e.g.: If the gateway of your router is 192.168.1.1, please change the camera’s IP to 192.168.1.X(X can be numbers from 50-100) and each camera has a different IP.

3. Add cameras on NVR

Please go back to the monitor which is connected with the NVR. Go to Settings—Camera—Add camera to add the cameras.

.

1. Connect the switches one by one, then connect the router and NVR with one of the switches.

2. Change the cameras IP to the same segment with the NVR’s LAN port.

Please go to Settings—Network—TCP/IP to check the IP of the NVR:

eg:

Please download the software SearchTool and install it on your computer (connected to the same router):

http://onwote.com/Download#Tools

Please use SearchTool to detect the camera. Then check in the cameras and click Batch Edit IP. Click DHCP to enable DHCP of your camera or choose IP Batch Manually Setting to change the camera’s IP address to the same segment with your NVR’s IP manually.

e.g.: If your NVR’s IP is 192.168.1.16, please change the camera’s IP to 192.168.1.X(X can be numbers from 50-100) and each camera has a different IP.

3. Add cameras on NVR

Please go back to the monitor which is connected with the NVR. Go to Settings—Camera—Add camera to add the cameras.

2.2. Tap on  and choose Scan code to add.

1.    Click one iamge and tap on  to view video in full screen.

2.

3.    Tap on the icon  and choose Super definition; Super definition mode requires higher internet speed.

4. 

  Click the playback button  to playback.

3. Please open SearchTools on your computer and search the cameras.

4. Please choose one camera, move your mouse to Preview, click on “e” to go to web client.

5. Your browser will open a page automatically, please login with admin and password 123456

6. Please go to Configuration—Image—OSD. Change Time Format and click on Save.

.

3. Please open SearchTools on your computer and search the cameras. Move your mouse to Preview behind the camera, click on“e“ to go to web client.

4. Your browser will open a web page automatically. Login the camera web page using Username: admin  Password: 123456

5. Choose Configuration—Event—Intelligent Detect, disable Draw rect in video, click on Save.

.

Here is the software for MAC: http://onwote.com/Download#Software#NVRTD…Series

Please download it and install it on your MAC. If you MAC doesn’t allow it to install the software, please go to System preference—Security& Privacy to change the authority.

Add device and view video on MAC

User: admin  Default Password: 123456

Choose Resource Management, click on Add

Click on Manually Add, change IP to Serial No.. Input the serial number and password of your system. Click OK to save device. (How to find the serial number?—Go to NVR monitor, choose Settings—Network—NAT, the serial number is below the QR code.）

You will go back to Resource Management page after you clicked OK. Please wait for 3-5 minutes, until the information of your device turns to black on this page, then go to Live View1*, double click on the Default area to view video.

.

Here is the new software for windows PC: http://onwote.com/Download#Software#NVRTD…Series

User: admin  Default Password: 123456

Choose Resource Management, click on Add

Click on Manually Add, change IP to Serial No. Input the serial number and password of your system. Click OK to save device. (How to find the serial number?—Go to NVR monitor, choose Settings—System—Information, the serial number is below the QR code.）

You will go back to Resource Management page after you clicked OK. Please wait for 3-5 minutes, until the information of your device turns to black on this page, then go to Video Preview1*, drag the camera to the right side one by one to view video.

.

.

a) Playback on NVR

1. Click Start  -> Playback, go to the NVR playback menu;

2. Select the date and time to start playback.

3. Click the time bar on the right side to playback the specific time period.

b)Playback on mobile app.

Open your app and click the playback icon  to playback.

Attention: Please use “VLC”player(https://www.videolan.org/vlc/index.en_GB.html) to play the video you back up from the nvr system.

1. Insert a USB disk into the NVR USB port. Click Start  -> Search and Backup;

2. Choose By Time. Click Set Backup Time.

3. Set backup time, click OK.

4. Click + inside the windows to add camera.

5. Click Backup to back up video to your USB disk.

Please pay attention to the position of the Waterproof O ring. The end connected with the camera must be higher than the end connected with the Ethernet cable.

.

.

.

<p>The post ONWOTE Poe NVR Setup Guide first appeared on NVR IPCAMERA SECURITY.</p>

Safety Caution

All PRODUCTS & PARTSThis product may require cabling,we suggest to test all products&parts before installation and cabling×Dismiss this alert.

Nvr product description

1.  WIFI Antenna Ports:Double antennas to WIFI range

2. WAN Port:Connect your NVR to Internet

3. VGA Port:For viewing on VGA monitor

4. HDMI Port:For viewing on HDTV

5. USB Ports:For mouse and backup

6. Power Input

IP Cameras product description

①. WiFi antenna:WiFi connection with NVR；
②. DC Port:input power 12V 1A;
③. Reset Button:press reset button for 10 seconds to restore factory setting and enter into matching-code mode;
④. RJ45 Port:for pair the camera with NVR,or connect the camera by wired connection

Note:Working temperature ranging from -13 degrees Fahrenheit to 122 degrees Fahrenheit.

Installation Instruction of WIFI NVR KIT

EseeCloud Wireless Security Camera System Installation

Read More : Wi-Fi NVR Kits User Manual

Note:The NVR can work with the router by wireless connection and wired connection Wired connection: when your NVR connect by RJ45 to your router,it will get network settings automatically Wireless connection: right click your NVR mouse and choose System Setup→Network Setup→Wireless Internet→Enable the Wireless LAN→find your own wifi network,and put wifi password here (pls notes it doesn’t work with 5G WIFI network)×Dismiss this alert.

Setup The System

This system is standalone with embedded Linux Operating System in the NVR. Just like a desktop PC, need to hook a screen to the NVR to enter the OS .Any TV,monitor with VGA or HDMI input should work for it.

If you connect the NVR with monitor shows Hiseeu logo or shows black,normally it is your monitor resolution is lower then the NVR.You can press the left side of the mouse for 30s,then it will reboot.

If still can’t work,pls change a monitor,thanks.

When you turn on the NVR box, the monitor will get below interface: Setup Wizard- -Down- -General setup- -Next -wireless setup- -Next- -Fast network- -Next -Format the hard drive- -Next

CHECK NVR NETWORK , CHANGE NVR SYSTEM LOGIN PASSWORD

Once you have completed connecting the NVR,wait approximately 2-3 minutes.Next you will see the window below on your monitor screen.For your first time to login in,User name is admin,there is no password,just choose ok to get into the menu.
(if you forget the password,pls find the solution on the FAQ page)

Tips: To protect your privacy,please set your password at earliest convenience(don’t set the password over 8 characters).Right click the mouse→System Setup→System Admin→User to set password.

How to check if your Cloud is online and Network status is healthy ?

Right click the mouse of the register,choose Fast Network.In the middle of the window you should see Cloud status as ONLINE and Network Status as Healthy Network.

If this does not appear, select Manual Config then enable DHCP,Click Apply,then power off the NVR box,wait a few seconds and power up.

Once you power up, repeat the steps outlined as above.Cloud status must be ONLINE and Network Status must be Healthy Network.If this does not happen,you will not be able to view remotely

Menu Do What

Menu bar

Split Screen: change status of live view.You can choose to view multiple cameras or any single camera.

Video Manage: manage IP cameras and NVR channels.

System Setup: all system settings.

Video Playback: playback recorded videos.

Video Backup: backup recorded videos.

Color Adjust: adjust the image setting of the each camera

PTZ Control: control PTZ camera

Volume: Adjust volume of audio cameras(works only for audio cameras).

Setup Wizard: step by step guide of 1st time general settings.

Fast Network: shortcut to network settings.

Wireless Add: add IP cameras into NVR channels wirelessly.

Exit System: logout,reboot,close screen output and shut down the system.

System Setup

Click right button→Choose System setup; enter the menu that enables you to do all settings related to this system.

Menu Do What

There are 3 modes for reocrd.

Note: Users can setup any period of time they want,for example 0:00:00-23:59:59,That’s 24 hours×7days recording.When NVR detects hard disk,the default setting will be 24 hours×7 days recording.

The priority of Alarm is higher than that of Motion,and the priority of Motion is higher than that of Time.

Video Playback

Steps: right clik mouse in main menu→Video playback→choose date,channel,record mode→click search→then can view playback file.(IE browser can’t check the playback directly,so you can use the Eseecloud software on computer or check on your phone app Eseecloud and IP RPO)

Warm prompt:

1.IIIustration for playback button: play, pause, fast forward×2,×4,×8

2.Play file:Choose the recording file in file list,as number “1” shown in picture.Choose one of the recording,click “play” to play to recording file;

3.Video backup:Choose the recording file in file list,as number “1” shown in picture.Insert the U flash disk,click “video backup” to backup the file;

4.Timeline: Click “date”and “time”at left bottom to check the timeline of recording,as number “2″ shown in picture;

5.On the timeline with recording file,left click the mouse,the can playback the file.

Notes: you can see four channel cameras playback at the same time,if you want to check other channels you need select the correct channel at first,then choose search to find it playback.

How to Backup the video

Use U disk to copy video,so easy and convenient!

The playback files is avi. format, you can use VLC player to check it on your computer VLC player.
download link: https://www.videolan.org

View on PC via lE or Eseecloud and Phone APP Eseecloud or IP PRO

To View on the the PC

To view on browser,you have to connect the NVR and your computer to the same router.Enter the IP address of NVR on the browser’s address bar.(We recommend using IE or Micorosoft Edge) Right click the mouse→system setup→Network Setup→IP address (Start with 192.168… )
You can change language on the right top corner.

To view on Eseecloud software on PC

Input Cloud ID (Right click the mouse→fast network→Cloud ID)
Input User Name and Password (If you doesn’t change the user name and password,User Name is admin ,no password)
please download Eseecloud software from： https://ipproapp.com/computer
user name is admin,no password,choose login

*Select “Add”
*Select “Cloud ID”.enter the cloud ID(9 or 10 numbers).You can find it on your home monitor screen.
Or right click the mouse, choose Fast network find cloud ID here
* Username is NVR system user name on your home monitor screen
* Password is your NVR system password on your home monitor screen.(If you don’t change It in your setup,it should be no password)
* Channels: Input 4 or 6 or 8. If you have 4 cameras,enter 4 etc.
* Click Confirm and you will see the video.

if you check in the local network,you can use the NVR IP address to add the system (Find the IP address on Fast network page or Network setting page)

To View on IE browser

Find the IP address: right click your mouse and choose Fast network, you will see the IP address here.
Enter the NVR’s IP address in your IE browser for example: http://192.168.1.105(If the default WEB port 80 has been changed e.g. to 100,you need to add new port number when input IP address in the browser,for example: http://192.168.1.105:100).

To view on the Phone

Users can use cellphone to scan the QR code below to install the APP free of charge,or users can search “Eseecloud”or ’IP PRO‘ on APP store or Google Play then install the APP.

Click “+”→other ways to add/ scan the QR code on your fast network page→Network connected device→input Cloud ID and User name and password (user name and password is the same one you login in NVR)

Tips: if you’ve set a password on your NVR system,please update your password on APP to view.
And if your camera loading for a long time and don’t show image,you can right click your NVR mouse and choose System Setup→Network setup,change the MTU to 1000.

Playback On Mobiles

In the Eseecloud APP,while viewing live video of the system,click Playback,you will enter the remote playback menu.The APP Playback only check one channel at one time

Tips: Videos in playback are HD mode for real time which requires very good transmission condition.
We suggest to playback in LAN.Remote playback out of LAN may not 100% work due to connection & network condition.

Extend WIFI Range

Wireless connection is easy and convenient, but it’s not universal application. Because of the character of WIFI, the WIFI signal will decrease when going through some obstacles Some methods can be applied to bypass obstacles and extend WiFi range.

Position The Antenna Correctly

WIFI range is like an apple and the antenna of NVR is in the center of it.WIFI signal is strong all around the WIFI range.Antenna of NVR should be put straight up,if not,WIFI signal will be weak.
According to the signal transmission character of antenna, the antenna of cameras should overlap or parallel to NVR WIFI range,as pictures showed below:

Use Antenna Extension Cord to prolong WIFI distance

Installation method of antenna extension cord

Note:When WIFI signal is not strong enough against walls,users can take off the original antenna and subtitute antenna extension cord.Drill a hole on the wall to let the extension cord go through and simply it where WIFI signal is strong.

Set up cascading connection in a reasonable solution,extend wifi signal transfer distance

Note:
Repeater function can’t strengthen WIFI signal for wireless NVR kit, but can extend the distance by repeaters→WIFI cameras.

Only when the repeater cameras and repeated cameras are positioned correctly,WIFI distance will be extended.

Repeater function and 3 meters antenna extension cord are two methods to extend WIFI range.
Users can choose one according to real situation.

Repeater Setup

Step 1. Right click the NVR mouse,and choose “Video Manage”- -then left click Repeater”

Step 2. Add repeater
As picture shown below,click icon + besides channel 3,choose other channel.

Step 3. As picture shown below, it means IPC1 is connected to NVR through IPC2 and IPC3.
IPC2 is connected to NVR through IPC3.IPC3 is connected to NVR directly.

Step 4. Click “Apply” and then click “refresh” to check if the setting is successful.

Delete Repeater

Move the mouse to targeted channels,left click to delete,and then click “Apply” and “OK”.

Application Example

As picture shown above, when IPCAM1 is put somewhere is out of NVR WIFI range,and there is IPCAM2 between them with strong WIFI signal,users can put IPCAM1 close to NVR and power it, setup IPCAM1 repeated by IPCAM2, and then install IPCAM1 to the presupposed place.

Camera add failure reasons and solutions

Q1: Failed to add the camera for the first time

Check whether the green light of the camera flashes normally. If the camera status light is not flashing green, use a thimble to lightly insert the configuration hole or long press the reset button until the camera indicator flashes.

Q2: Determine whether the binding failure caused by the router settings

1. The router has been set up to prevent Wi-fi squatter If the Wi-Fi connected to the camera is set to prevent Wi-fi squatter(black and white lists, MAC address filtering, etc.), the camera will not be able to connect to the Internet. The router’s prevent Wi-fi squatter settings need to be canceled.

2. The router is set up with 5GHz band wireless WiFi The camera does not currently support the connection of 5G band WiFi. Please open the router management page (generally marked with the address of the management page on the bottom label of the router), select the wireless setting 2.4GHz, and set it to on.

Q3: Check whether the mobile phone prohibit the permission of  EseeCloud to use data, WLAN, GPS

Domestic Android phones may prohibit the use of data, WLAN, GPS permissions for this application, resulting in the camera being unable to connect to WiFi. Solution (Android phone): Open the phone settings center-click “application management”-open the above permissions

Q4: Make sure that the WilFi account and password are filled in correctly

It is likely that the Wi-Fi account and password you connected to the camera are incorrect, resulting in the camera not being able to connect to the network. In particular, pay attention to whether there is a space input, and try to avoid complex and uncommon symbols.

Q5: Other questions

1. If the router is set to bridge mode, the WiFi signal will be unstable, causing the connection to fail. It is not recommended to use WiFi in bridge mode when the camera is networked.

2. If you are a campus / enterprise user and the school 1 company assigns each student / employee a static IP to access the Internet, you can manually enter the static IP information to access the Internet.At present, this situation is not supported by camera networking, need to select other available WiFi connections.

3. The camera does not support WPA / WPA2’s “enterprise” encryption method to connect the camera to the network. Support WEP, WPA–PSK 1 WPA2–PSK, or corporate WiFi without password. If the camera is networked in the corporate network environment, please confirm in advance whether the WiFi encryption method meets the camera networking requirements.

What should do if the camera is offline?

Q1: Camera offline processing method

1. Check whether your device is power-on and the status light is on;
2. If you are using WIFI connection, please confirm whether you have modified the WIFI in the environment where the device is located-including the WIFI password and name, if modified, please reconfigure WIFl;
3. If the reason cannot be resolved, please restore the factory settings and add the network again.

Device preview help

Different devices support different functions. Preview interface only shows the functions supported.

Light control:setup on/off,brightness,color temperature for light control device

Screenshot:snapshot current preview image

Recording: record current preview video

Full screen:tap button and switch to landscape viewing

Calendar:choose playback time to show all recording files wanted

Remote playback: device must to be inserted TF card.

Two way talk:press the button and talk for a long time

Installation mode:swith to wall installation and ceiling installation mode

Display mode: at ceiling installation mode,there have fisheye mode,cylinder mode,corridor mode and fulI screen mode

Cruise: setup auto cruise .

Sound:setup the sound on/off

Swith code stream:switch HD and SD

Split screen dispaly: choose screen channel number

Screen aspect ratio: can set the screen aspect ratio

PTZ control: control the movement of high speed dome

Timeline:drag the time line left and right to choose recording period . Use fingers to zoom in or zoom out the timeline

Add Camera

Add device

Method 1: Enter to device list interface after login, click the t’ button in the upper right corner of the interface, and select the add device” button.
Method 2: Click the’+’ button in the interface to enter directly to add device interface.

add camera

1. There is a QR code on the device body:
Scan the QR code on the device,display the device ID of the current device , click the Add ICON below jump to the prompt interface of operation guide.

add cameraadd cameraadd camera

2. Can’t find the device QR code :
lf there is no QR code on the device, click ‘Other ways to add’ and then select ‘Standalone camera’.

add cameraadd cameraadd camera

3. Please connect your mobile WiFi to the device hotspot.

Open Settings-> Select Wireless LAN > Select ‘IPCXXXXXXXXX’ device hotspot.

Connect hotspot,default password：11111111

add camera

4. After connecting successfully,return to APP.

Remote View: View video via WIFI or other network, please select Remote View.(most people choose)
Direct Connection: View video without network ,select Direct Connection. (few people choose)

5. Select Remote View to continue.
Select your wifi and enter your wifi password, then click Confirm .

add camera

add camera

6. Configuring, do not unplug the network! The network configuration process may take 1-2 minutes, please be patient.

add camera

7. Set device name and device password.
For added security, please set a password.

add cameraadd cameraadd cameraadd camera

Device Sharing
Generate shared QR codes ln the device list, click the “Share” button, set the right to share, choose to share, and generate QR codes.

Device SharingDevice SharingDevice Sharing

Scan and share QR code.
click on the’+’button in the upper right corner of the interface to enter to add device interface, click on scan add device, enter to scan interface, scan shared device QR code, after display the scan results then return to device list interface.
Note: You need to allow access to the camera and album to use this function properly.

Scan and share QR codeScan and share QR code

App Operation

Log in

This APP support “account log-in”, third-party log-in” and local experience”.
Account log-in: At log-in interface, input user name/cellphone number/email address and password, click ‘0K” and log in.
Third-party log-in: Click the icon of third-party network social software, authorize the APP to log in.Local experience: Users can use the APP without log-in.
Remember the password: Supportremem-berring the account and password that have been logged in, which is convenient for switching account login.
Note: Please pay attention thatLocal experience” mode will be stored at local.Once data is lost, it can’t be restored.

IP PRO Log in

Registration

Input cellphone number/email address to register, get verification code.
Input verification code and password, click “OK”. After registration it will move to device list.
Note: Each cellphone number/ email address can be used for registration once.

IP PRO RegistrationIP PRO Registration

Reset Password

Input registered cellphone number /email address to get verification code. Input verification code, reset password and click “OK”.
Then go back to log-in interface, log in with new password.

IP PRO Reset Password

Frequently Asked Questions

Question one：After installation, open the CMS and display “Cannot load plugin”?

Answer one：

1.Please confirm whether the installation path uses Chinese when installing, and the plugin is temporarily not compatible with Chinese path.

2.After confirming the non-Chinese path, if the problem persists, you can contact technical support for assistance.

Question two：After connecting multiple channels of video (more than 30 channels), videos stop for a few seconds , all channels are automatically disconnected into the black screen. The device connected again has no response. Do we need to restart the CMS?

Answer two：The new version of CMS3.0.1 runs with higher memory. If you connect many channels by the lower configuration computer, the computer system will run out of memory, causing the CMS to run abnormally. If the computer configuration is slightly lower, it is recommended not to connect too many channels. The optimization work has been planned for this situation.

Question three：When CMS is installed on the OSX system, it displays “File is corrupted” or “Unable to open” when it is opened?

Answer three：

1.Open “System Settings” → “Security and Privacy” → “Allow applications to be downloaded in the following location”, check “any source” (applies to versions prior to OSX10.12.X);

2.Open “Terminal”, enter the string “sudo spctl –master-disable”, press the “Enter” key, enter the sudo password (applicable to versions after OSX10.12.X). If the above method still does not work, please contact us to help you solve it.

Question four：After starting a window and flashing, it will not start or XP will appear. Open the software to indicate 0a00000000 memory referenced by 0x00000000 instruction. The memory cannot be ‘written’.

Answer four：Large probability video card driver problem, update the graphics card driver can solve

Question five：It shows  mfc100u.dll lost when opening computer

Answer five：Install VC++2010 library to solve the problem

More features

User Management

New user：①Click New User ②Enter username (required) + note name (optional)③Click to confirm

Modify permissions：

Default: The default permissions include screenshot, video, PTZ settings, video playback, remote download 5 items

modify：①Click edit permission ②Check the permissions and devices/channels that need to be assigned to new users (you can click to select all) ③Click to confirm

Other functions：

        ①Clear password: If the login password of the new user is forgotten, you can log in to the newly created user again by directly clearing the password and the internal setting data can be retained.

        ②Modify the note: Add a note, change the note or delete the note, go to the modify note operation

        ③Delete user: If you feel that the newly created user is not necessary, click delete user to delete the user.

New userModify permissionsModify user

Log query

Inquire：①Confirm ‘start time + end time’②Confirm ‘log type’ (including: alarm log, login log, operation log)③Selected area ④Click to query

Log query 

Resource management

Screenshot：

search for：①Select ‘start time+end time’ ②Click search

Preview：①Method one selects ‘preview’ for right-click operation ②The second method is the screenshot file retrieved by direct click.

delete：①Method 1 Select ‘Delete’ for the right-click operation. ②The second method is to enter the screenshot preview state and click to select ‘delete’.

location：①Method 1 Select ‘Open location’ for right-click operation②Method 2 is to click ‘Save Location’ in the resource information.

Resource information：‘user, resource size, resolution, device name, associated channel, screenshot time, save location’, including the above content (as shown in Figure 2)

Replacement size：‘Original size, maximize, zoom in, zoom out, resource information, delete’, the screenshot preview status includes the above status/function that can be switched to

video：

search for：①Select ‘start time+end time+’②Select the recording type (including: preview video, playback video, default all types)③Click search

Resource information：‘user, resource size, recording type, device name, associated channel, recording time, save location’, including the above

Other functions：The operation steps of ‘preview, resource information, location, delete’ function are the same as the screenshots. For details, please refer to the operation in the screenshot.

Right click operationResource information

System Info

Version Information：The content is displayed as follows ‘version number, date’

change Password：①Enter ‘original password + new password + confirm new password’②Click to confirm ③Re-login verification password

sign out：Click the ‘Exit Login’ button to quit the login status of the current account.

System Info

User parameter

Basic Settings

Split screen number：The selected split screen number is displayed after the re-login, and the CMS provides split screen 1/4/6/8/9/16/25/36/49 nine forms of choice.

Display language：CMS currently defaults to 9 display languages, such as Simplified Chinese and English. When you choose to log in again, you will switch to the corresponding language.

Login Method：The cloud login mode is online. You need to connect to the external network when you log in. The local login does not have this hard requirement.

List style：The list style includes tree shape and graphics. The replacement is only the real-time preview interface and the display of the device list under the playback interface. The device list under other interfaces is unified into the tree list style.

Path modification：

①Screenshot path: The screenshot file is saved in the snapshot folder by default, and can be saved in other paths according to its own needs.

②Local recording path: The local recording file is saved in the record folder by default, and can be saved in other paths according to its own needs.

③Video download path: The files downloaded by the playback video are saved in the video_download folder by default, and can be saved in other paths according to their needs.

Preview sync time：Check the time when the device is previewed and the computer will be automatically synchronized (only ipc is supported)

note：After modifying the settings, click “Finish” and you will need to log in again. (It is best not to modify it to a directory containing Chinese)

advanced settings

Time zone setting：The local time zone can be selected according to the actual situation.

Automatic lock：Check the auto lock and enter the integer in minutes in the time frame. If no operation is performed on the CMS within the time of the input, the CMS will automatically lock.

Automatically connect video：After logging in to the auto-connect video, log in to the CMS and automatically connect to the device added to the device list. The number of connected channels is the number of split screens in the basic settings.

Basic Settingsadvanced settings

Equipment management

Add device

Add a LAN device：①Enter the device management interface ②Refresh LAN device ③Check the device and click Add (LAN device can be filtered by entering IP/ID in the filter box)

Add cloud ID device：Manually enter the device ‘cloud ID number + channel number’, select ‘type’ according to the actual situation of the device, and the rest can click to confirm (the password can be selected according to the actual settings of the device)

Add an IP/DDNS device：Manually enter the device ‘IP/DDNS+port+channel number’, select ‘type’ according to the actual situation of the device, and the rest can click OK.

LAN add

Modify device

Device modification：In the device management or preview interface, after selecting the device and clicking Modify, the device interface will be loaded.

Regional modification：In the modify device interface, click the area drop-down box.

Group modification：After selecting the group under the device management interface, click the modify button to load the modified group information interface.

note：Modify the channel name, panorama, and channel type corresponding to the channel number in the device.

The panorama or channel type corresponding to each serial number is independent.

The channel device in the device needs to be in the panoramic state. You can select the corresponding channel serial number to modify the panorama. And channel type

Device modificationGrouping

Remote setting

VR CAM/gateway Remote setting

Setup steps：①Selected device ②Click Settings / Connect Device and click the Remote Settings button (as shown in Figure 1)

Device Information：Content includes device model, device ID, OEM serial number, firmware version (providing check updates)

Function setting：The audio, prompt tone, prompt language, and display mode and resolution can be set on the configuration.

Alarm system：The content includes motion detection, message push, motion detection sensitivity, and synchronization time function. If daylight saving time setting is available, you can set daylight saving time.

TF card settings：TF card status, available / total capacity, TF card formatting function

note：

①Alarm message push is not supported in local login. You need to check to switch to cloud login status.

②Currently supports VR CAM/gateway devices for remote setup

Remote setting interface

D82 series NVR remote setting

Setup steps：①Selected device ②Click Settings / Connect Device and click the Remote Settings button

Device grouping

Create a group：①Click the ‘Create Group’ button ②‘Enter the content in the group name box and click OK.

Add channel：

enter：①Select the created group ②Click the Add Channel button

Import selection：①Selected channel ②Selected group ③Click the import selection button

Import all：①Selected group ②Click to import all buttons

Modify/delete：

Edit: Select the group and click the Modify button to modify it.

Delete: delete the selected group or channel and click the delete button to delete

Create a groupAdd channelModify group

Video playback

Video playback

Playback four steps：①Select device channel ②Select video type ③Select playback date ④Confirm search video

Device channelVideo typeDate selection

Timed playback

Timed playbackTimeline

Video sync

Steps：①Retrieve video  ②Check sync  ③Switching time point

Video download

Batch download：Enter the time period to be downloaded at the start time + end time according to the needs of the retrieved recording time range.

Time period download：The time period of the video recording will also be displayed in the download resource. Click the download button for any time period according to your needs.

Custom bulk downloadSelect time period to download

Other functions

Playback control：Support playback/pause/stop control in video playback, select the screen form in playback and click operation

Time scale adjustment：The settings in the Setup Wizard are not set. The playback timeline scale will default to 60 minutes. You can also modify the scale value by clicking ‘Reduction’ or ‘Magnify’ during video playback.

Playback controlAdjustment scale

Live Preview

Connection/Disconnection

The list style is treeshape:

connection：

①Double-click on the selected device/channel to enter the connected video state.

②After selecting the device/channel, right click and select “Connect Video” to enter the connected video state (Figure 1)

disconnect：

③Double-click to disconnect the current connection after selecting the connected device/channel

④After selecting the device/channel, right click and select ‘Disconnect’ to disconnect the current connection.

Figure 1

List style is graphic：

①After selecting the device/channel, click the play button on the device list to enter the connected video status.

②After selecting the device/channel, click the stop button on the device list to disconnect the current connection status.

③Right-click operation connection/disconnection is consistent with the tree list style. The specific operation can be referenced.

Note：poor performance of the computer will directly affect the smoothness of the preview video. It is recommended that the number of channels connected to the device be gradually increased

Video/screenshot

Video：

①Click the Record button on the toolbar to enter the video recording status (as shown in Figure 1 below)

②After the video operation, click the record button again to stop recording.

Note：

①The actual recording duration is not equal to the time difference between the start recording time and the end recording time.

②If the device network is interrupted, the recording will succeed but no video file will be saved.

③The channel is maximized or minimized during recording, and the recording will stop.

Screenshot：

Click the screenshot button on the toolbar to enter the screenshot status (as shown in Figure 1 below)

Note：

①If the switching stream video is not loaded, the screenshot operation will be saved.

②The screenshot does not have the function of continuous screenshots. Clicking the screenshot button once will capture an image.

Figure 1

Panorama mode

enter：

①Double-click the channel screen to enter the maximized state, right click and select “panoramic mode” to switch to the panorama mode, enter the panorama, and the code stream is automatically switched to HD.

②The channel screen is in 1 split screen mode, and the panorama mode option is available on the right toolbar. Click to select to switch the panorama mode.

drop out：

①Click on Panorama mode on the right toolbar and select ‘Exit panorama’ to exit panorama mode

②Exit the panorama mode by exiting the screen from the split screen state.

Panorama modeCylindrical modeExpand modeSplit screen modeQuad screen modeSix-screen mode

Note：

①In the local login mode, you can select 6 display modes in the panorama mode, including: panorama, cylinder, expand, 2 split screen, 4 split screen, 6 split screen

②In the cloud login mode, you can select 4 display modes in the panorama mode, including: panorama, cylinder, split screen, quad screen

        Suspension: the direction of the cruise is clockwise

        Wall-mounted: the direction of the cruise swings left and right

       Speed: Cruise provides speed 3S / speed 40S / speed 60S three options, corresponding to slow / medium / fast three speeds

       Stop: Pause the current state of the cruise, left click on the channel in the cruise or select the stop cruise button in the cruise mode to click

Panorama modeInstallation modeCruise mode

PTZ control

Cruise / PTZ / Zoom / Focus / Aperture / Preset：

The PTZ control function can be used only when the PTZ device (such as a ball machine) is connected to the main control device (such as NVR or DVR).

Cruise is to directly perform the screen cruise operation. The pan/tilt is to adjust the lens direction and zoom to replace the mirror multiple.

PTZ speed level controlcontrolZoom, focusPreset

①：Adjust the PTZ control speed (default level is 6)

②：Adjust lens direction and cruise

③：Adjust the zoom and focus of the PTZ camera

④：Set and call the set bit, adjust the lens to the specified position, set the preset position, input the preset position later, click to call, the lens will automatically move to the specified position

Split screen number

When the number of connected device channels is greater than the current number of split screens, the displayed split screen will automatically increase, reaching 49 split screens.

Split screen number

Other functions

Other functionsIntercom

User login

Local login

①Enter account + password  ②Click to login

Login accountforget password

note:

Cloud login

Note:

①The cloud login should be logged in with the registered account (the account registered by the mobile app can be logged in)

②Registered account is recommended to use a valid mailbox, easy to retrieve passwords and other special circumstances

③After registering an account, you need to log in to the email address you entered during registration to activate the email address (click the received link to verify)

④The mailbox status is not activated, and cannot be retrieved after forgetting the password (activation period is two days)

⑤The first time you use EseeCloud_CMS, the software’s time zone will automatically sync with your computer, and you can change it later in the advanced settings.

Login accountRegister a new accountRetrieve password

Installation login

Installation and operation

Step 1: Run the EseeCloud_Setup_3.0.1.exe installation package

Step 2: Select the display language when installing

Step 3: Read and determine whether to accept the agreement

Step 4: Determine the path to the installation

Step 5: Installation is complete and you can choose to run immediately

1. Running program2. Choose a language3. Reading agreement4. Determine the path5. The installation is complete

Introduction to EseeCloud CMS

Function introduction

CMS is called Camera Monitor System. It is a camera monitoring client for online preview image, video storage, remote playback, device management, video/screen download and other functions. 

It is suitable for DVR, NVR, IPC, VR CAM, Wifi IPC and other devices.

Camera suitable for IP PRO, VR CAM, EseeCloud app.

CMS has the following characteristics

 Interface containerization processing mode: In the interface design of the client component, the containerized processing is carefully adopted, which simplifies the processing mode of multi-screen and single-screen switching, greatly improves the multi-screen operation feeling, and adapts to the development trend of a multi-screen PC.
.

Channelized management mode: In the client component design, channelized management mode is added, and the traditional design mode with device as the core subject is abandoned, which is more suitable for the development direction of IP monitoring.

Operating environment

Operating system:Microsoft Windows7 / Windows 8 / Windows 10 (32/64 bit Chinese and English operating system)

OSX 10.9 or higher (64-bit Chinese and English systems)

CPU：I3/2.4GHZ or more

Memory: 4GB or more

Graphics card: integrated graphics (Intel HD 4000 and later), discrete graphics (NVIDIA GeForce GTX 460 and later)

note

Preview multiple video or high resolution video at the same time, requiring higher hardware configuration and network bandwidth

Foreword

Foreword

Welcome to use our products! We are very honored to get your trust.

In order to have a general understanding of our product CMS and facilitate your use, we have specially configured this manual for you, including the function introduction, operation steps, precautions, etc., which are essential guides for your use of this product.

Please read the instruction manual carefully before use. I believe it will be of great help to your effective use of this product. In addition, if you have any questions during the use, please feel free to contact us, we will be happy to serve you.

Applicable Model

This manual is for the camera monitoring system CMS.

Statement

This manual may contain areas where the product functions or operations do not match, or where the technology is inaccurate, or a typographical error. For such problems, our company will update the manual content according to product updates, and regularly update the hardware and software products described in this manual. The updated content will be added to the new version of this manual without prior notice.

The contents of this manual are for reference guidance only, and are not guaranteed to be identical to the actual product. Please refer to the actual product.
.

Agreement 

In order to simplify the description in this manual, make a convention:

The camera monitoring system CMS is referred to as CMS or software for short;

DVR, NVR, IPC, VR CAM, WIFI IPC equipment, etc., collectively referred to as equipment;

Click for the left mouse button click, double click for the left mouse button to double click;

Some pictures are schematic, please refer to the actual interface of the software;

A “note” hint text may appear in this article to indicate that the operation is potentially risky, and ignoring the text may result in errors or unpredictable results.

Cloud storage details

Features

1. What is cloud storage? The cloud storage function is a video storage function developed based on technologies such as moving object detection. Cloud storage is divided into two types: alarm recording and full-day recording. Alarm recording refers to triggering the camera alarm when someone passes by or moves in front of the camera. The camera will automatically record and upload it to the Cloud Space Security Center for encryption. You can use it with confidence.  

 Tips:  

 (1) As long as you purchase the cloud storage service, you can get the corresponding cloud space. For example, if you purchase the cloud deposit monthly package, the cloud space is valid for one month, and it will take effect from the successful purchase. 

(2) The storage time of cloud storage video is determined by the type of package. If you open the cloud storage package for 7 days, the camera cloud video storage period is 7 days. The 30-day cloud storage package will be opened, and the camera cloud video storage cycle will be upgraded to 30 days. If you open a 7G/month cloud storage package, then your cloud recording storage space is 7G in this month. After the space is full, the cloud recording will not be saved. The stored video will be saved for one month.  

 2. What are the advantages of cloud storage? The video is safer: the video cloud storage can not steal, safe and reliable. More efficient viewing: generate alarm video in real time, quickly grasp the alarm situation, the video is clear and smooth without jamming Cloud storage: Camera video is stored in cloud space, no space limit, and unlimited cloud storage space.

Cloud deposit purchase and exchange

1. How to buy a cloud storage package?
Click the device list device “Cloud Record” button or the personal center “Cloud Mall” – enter the “Cloud Mall” interface – click “Switch” to select the device you want to purchase and the device channel – automatically select the appropriate package for you after the selection is completed – click ” Buy now” Once the payment is complete, you can turn on device cloud storage.
Tips:
(1) Cloud deposit does not support return and exchange after purchase, and does not support refund;
(2) The purchase channel of the device is determined by the number of package service channels of the system. If the system has only two packages with service channels 1 and 3, then the device can only select 1 or 3 purchase channels;
(3) Cloud storage is only bound to the purchase user. The device with the cloud storage is deleted and added to the new account. Under the new account, the device will not be able to continue to enjoy the cloud storage;
(4) Cloud storage is purchased by a single device and device channel, and multiple devices and multiple channels need to correspond to multiple cloud storage packages;

2. How to redeem the cloud storage package?
Click the device list device “Cloud Record” button or the personal center “Cloud Mall” – enter the “Cloud Mall” interface – click “Use Cloud Saver Code” – enter the “Scan Redemption Code” interface, scan the valid redemption code – enter the ” redemption code” Payment interface” – select the device and channel to be redeemed – click ” redeem now” to complete the redemption

Tips:
(1) The number of channels for redemption Device is determined by the number of package service channels generated by the redemption code (if the service channel of the redemption code package is 4, then the device can only select 4 channels to purchase);
(2) There is no charge for redeeming the code cloud storage package using the redemption code, and each redemption code can only be used once;

Cloud video introduction

 Cloud recording is divided into two types: alarm recording and full-day recording.

Alarm recording, the video will only be uploaded when the camera detects that someone has passed, the item has been moved, and the camera alarm is triggered.

Recording all day means that the camera will automatically record when it is online and in good condition. It will be detected 24 hours a day and encrypted and uploaded to the cloud space.

The cloud video is lost when the device is deleted, the device uploads the cloud video, and the device is disconnected from the network. The device and the server are disconnected. The device network bandwidth is insufficient and the device cannot upload video and video.

After purchasing the cloud storage package, the cloud recording function will be automatically enabled.

You can click the “Cloud Recording” button corresponding to the device list to enter the cloud recording interface. Click the cloud storage service icon to enter the “Cloud Storage Service” – disable the cloud recording function.

Tips: After the cloud recording function is turned off, the validity period of the cloud storage will not be extended;

Cloud retention period

1.Cloud deposit validity period
Cloud deposits take effect from the date of purchase, that is, the validity period of cloud deposits is: “at the time of purchase” to “the same time point after one month / one year later”. For example, the cloud deposit package of 7 days/month was purchased at 0:00 on April 1, 2019, and the validity period of the cloud deposit is a natural month. It is: 0:00 on April 1, 2019, and O:00 on May 1, 2019.

Tips: The validity period of the channel cloud is the sum of the time of all the cloud storage packages in the channel. For example, channel 1 purchased two 7-day/ month cloud storage packages at 0:00 on April 1, 2019, then the cloud storage validity period is: 0:00 on April 1, 2019, and June 1, 2019. 0:00 on the day.

2. Can the cloud validity period be suspended?
Cloud storage is timed from the date of purchase, and will not stop during the time. after the user purchases the cloud storage, the action of deleting or stopping the uploading of the video can not affect the cloud expiration time

Cloud storage renewal

1. How to renew the cloud deposit package?
(1) Conditions for cloud surviving fee: The current device has purchased the cloud storage channel to purchase or renew the cloud storage package;
(2) Process of cloud surviving fee: Click the device “Cloud Recording” to enter the cloud recording interface click the “Cloud Storage Service” icon to enter the cloud storage service – select the channel to renew the fee – click the “Renew Now” button below to enter the cloud mall interface – Select the channel and package for renewal of the device – click on the renewal fee immediately to complete the renewal.

Tips: When you are renewing, if the renewal plan are using the package and the other channels of the package meet the renewal conditions, it will default to select previous package and channel.

Cloud storage migration

1. Unbound cloud service migration

(1) Conditions for migrating cloud services: The current account has a cloud storage service of unbound devices;

(2) Migration cloud service process:
After the device is added successfully, if the device meets the service migration conditions, the migration prompt box is displayed. After confirming, select the service that needs to be migrated to the newly added device, and click “Migration”.

If the device is a single-channel device, the device migrates directly to the device list interface. If the device is a multi-channel device, you need to select the number of channels equal to the number of services to migrate.

2. Offline device cloud service migration
(1) Offline device cloud service migration conditions: the current account has offline devices that have been bound to the cloud service;
(2) Migration process:
After the device is successfully added, if the device meets the service migration criteria, the migration prompt box is displayed. After the determination, the device iumps to the miaration interface.

b. Select an offline device to migrate. If the offline device is multi channel, you need to select the migrated device channel.

If the device is a single-channel device, the device migrates directly to the device list interface. If the device is a multi-channel device, you need to select an equal number of channels to migrate.
Tips: Do not migrate all day recording cloud services to NVR devices

FAQ

When added by LAN or cloud lD,indicate “device is not online” or “device is not registered”

1.Please make sure the network is normal and already enable DHCP on router.

2.lf users manually change network parameter of device,please change it to default parameter. Just press reset button for 10 seconds.

.

Device is online and there happen alarm , but cellphone gets no message?

1.Please make sure the APP is on and allowit to get APP push message,then it can get alarm notification.

2.After enable push message,check cellphone setup-application management,find out the “Eseecloud ” and enable to get push message.

.

Indicate “SD card error” after insert SD card.

1.Only support SD card max 128GB and FAT32 format. If the system file is error,please formart the SD card and choose FAT32 format.

2.When SD card is ruined or file system is wrong,please try to change or re-format the SD card.

.

Why the playback recording video content is uncontinuous?

1.For saving the room of SD card and extend the lifetime,device will only make recording when detect the actived image ,that’s why the recording content is uncontinuous.

.

Can the device support be powered by USB or power bank?

1.Suggest to use original power adapter. If use other adapter with the power is not stable,the device may be damaged.

.

Device preview help

Different devices support different functions. Preview interface only shows the functions supported.

.

<p>The post EseeCloud Wireless Security Camera System Installation first appeared on NVR IPCAMERA SECURITY.</p>

This product is widely used in banks, telecommunication systems, electricity power departments, law systems, factories, storehouses, uptowns, etc. In addition, it is also an ideal choice for surveillance sites with middle or high risks.

Main Features