How to add a Hikvision NVR to Hik-Connect

Before you start…​

Part 1: Enable Hik-Connect on the NVR…​

.

.

.

.

Part 2: Set up Hik-Connect on your mobile phone or tablet…​

.

.

.

Part 3: Add the NVR to your Hik-Connect account…​

.

.

.

Other tips…​

Guides for Hikvision NVRs with V5 firmware

How to set up motion detection and alerts on a Hikvision NVR

What is Motion Detection and why is it useful?​

Motion detection is one of the easiest events to set up and will notify you as soon as a person or vehicle enters a predefined detection zone in your scene. Traditionally, it would just rely on lots of pixels changing between frames in your camera’s video stream, which would indicate movement in the scene.

Of course, this would cause lots of alerts for things you are not interested in, such as animals, moving plants and rain. Hikvision’s Acusense cameras and NVRs now have something called Motion Detection 2.0, which cuts the false-positive detections right down as will only notify you when people and/or vehicles are in the scene by learning what they look like. In this simple step-by-step guide, we will show you how to get motion detection set up on the new NVR 5.0 web interface.

Step 1: Go to your NVR’s Motion Detection configuration page…​

Step 2: Configure your Motion Detection zone and rules…​

​

Quick tip…​

If you find that the camera preview is too small when drawing your detection zones, you can switch the view to full screen by clicking on the Full screen (four arrows) button in the toolbar, and then exit full screen by pressing Esc on your keyboard.​

Step 3: Set the arming schedule to specify when you want Motion Detection active…​

​

Quick tip…​

If the 30-minute segments are not precise enough for you, you can finely tune a period of arming or disarming by double-clicking on the segments and specifying your start and end times in minutes using the arrows.​

​

Step 4: Set what you need the NVR to do when a camera detects a target…​

How to connect an IP camera to a Hikvision NVR

Adding cameras to your Network Video Recorder (NVR) is a crucial step in any CCTV setup. Not only does it allow you to store and access all your camera recordings in one place, but it also simplifies camera configuration. In this simple step-by-step guide, we’ll show you how to add cameras to a Hikvision NVR using the new NVR 5 web interface.

.

Why add cameras to an NVR?​

.

Before you start…​

Before anything, to be able to add your IP cameras, you need to make sure that:
.

.

How to add your cameras using the V5 GUI…​

Step 1:​

Open a web browser and enter the IP address of your NVR in the address bar. If you are not sure what this is, use the SADP tool to find it.​

Step 2:​

Log in to the NVR using the “admin” username and password you have set on it.​

​

Step 3:​

Go to: Device Access > Device Configuration > PoE Settings​

​

If you are connecting your camera via the Plug-and-Play method, then make sure that Network Camera Plug-and-Play is enabled on the POE port you will be connecting the camera to on this page.​

​

For any camera with a cable run under 100m, leave the Network Cable Distance as Short Distance.​

​

If you are connecting your camera manually by IP address, disable the Network Camera Plug-and-Play option for the channel that you plan to add the camera to.​

Step 4:​

Go to: Device Access > Device > Video Device​

​

For any Plug-and-Play camera, just make sure that it is in its inactive default state and then connect it to the port you reserved in step 3. After 20 seconds or so, the camera Status should turn to Connecting and then Online (you may need to click on Refresh to see this).​

​

For Manually added cameras, if you can see the camera in the List of Online Devices section, then just tick the box for the camera and then click + Add to Device List, which will then automatically add it to one of the channels you disabled Plug-and-Play on in the last step.​

Alternatively…​

Click on +Add at the top of the page and fill out the fields as follows:​

​

IP Address: Enter the IP address of your camera, using the ‘Test’ button to verify there is a camera at that address. ​

Device Name: This can be anything you like, as it is the name the camera will show with on your NVR. ​

Protocol: Select the camera’s manufacturer from this list, or failing that, use the ONVIF protocol (your camera will need to have ONVIF enabled for this to work). ​

Management Port: Enter the Server port set on the camera, which you can find in the SADP tool or in Network>Basic Settings>Port in the camera’s web browser interface. If you haven’t changed this, it is usually 8000 by default. ​

User Name: “admin” or the username of any other users set up on that camera. ​

Password: The password set with that user on the camera – if this is the same as the ‘Default Activation Password‘ you have set on the NVR, then you can tick this box instead. ​

Transfer Protocol: ‘Auto’ is normally best. ​

​

When these are completed, click OK.​

​

Your camera should then appear in the list of devices with an assigned channel, and an Online status, meaning it has been successfully added.​

.

Extra tips…​

Source : https://www.use-ip.co.uk/forum/forums/guides-for-nvrs-with-v5-firmware.71/

.

<p>The post Guides for Hikvision NVRs with V5 firmware first appeared on NVR IPCAMERA SECURITY.</p>

How about you? It can happen for everyone to delete the videos from their system unexpectedly. We are here to share details and needed information about retrieving deleted videos from your Dahua system and explain some system features.

Can I retrieve deleted CCTV.

How do you review and save the videos in Dahua NVR?

We are here to tell you how to review and copy the recorded video in the Dahua NVR setup system. In the first step, you need to go to the menu option, so perform right-click anywhere on the screen to view the menu option. On the opened screen, you see the items below:

An important feature is available on the Dahua NVR system: the automatic systems are good features on these devices. Dahua NVR system cannot only record the videos but also back up the recorded videos.

In case of saving the videos, there will be a wireless option in the NVR system. Various devices can be connected to an NVR USB slot to save the videos. Connect one of these devices and right-click the mouse on the screen to open the menu. You can search for the demanded video date and time.

 ..

How to download recorded video files to USB on Dahua NVR?

It is good to know how to download some recorded footage you want to view on your PC or laptop. The first thing to do is go to the main menu. It may ask you for your password first, so you must enter it.

You will see the backup option. Click Backup. When you go to the backup option, it immediately shows you something connected to the USB. In this case, the process offers you a USB drive connected to your NVR system’s back.

There is a USB port on the back of the NVR system and a USB port on the front. You can use either one of these USB ports. According to the manual, it can connect to an external hard drive and the USB port.

Some users needed help connecting to the USB port with the larger hard drives. Based on this information, we recommend you use a thumb drive if you have one. You can insert your thumb drive into the USB port, and there will be a pop-up window.

In this step, you can access the back file too. You will have 2 methods available. You can either go via the menu or put your thumb drive in. Go to the backup menu. You can file the backup. Both methods lead you to the same backup screen.

It is also to see the used or free storage of your device. It is possible to format the drive to make the storage lighter. Be careful because it is straightforward to format the drive suddenly.

 .

How to backup video from the NVR system to USB?

We want to tell you how to backup video from your NVR system to a flash drive or USB drive on a system running. This is one of the most practical features of the Dahua CCTV system, similar to other security camera systems.

Various systems use features similar to the NVR system. The first stage is logging into your system typically. There will be some boxes, and you can see the cameras on those boxes.

Then, right-click to go to the main menu. In this step, you need to enter your password. Then is the time to go to the backup option. You will see your USB drive name if you have plugged it into the NVR system.

You have to connect your USB drive directly to NVR, and then you can check the storage condition. It is possible to browse and select where to save the recorded files on your drive.

You can also format the drive if it is brand new or a drive with files on it, and you don’t want to keep any existing files. You can go to the format and perform the format step to bring it back to the new state with nothing.

After formatting, you will not need to choose the exact place for your recorded video. You only need to go back to the browse and select the folder. It is vital to check out the type of video. What kind of video are you trying to search for?

Do you want to search for an alarm, a motion, a motion and alarm, a general video, and an intelligent one? What stream do you want to search for? Typically, the mainstream is useful and practical for everyone.

Getting back up from videos in NVR

In case you need to get the backup, you need to consider the start and end times. You have to select the time of the demanded day. In this case, you can click the search button and observe your record channel.

You can decide which camera you want to pull the video by checking this channel. It can be easy if you are looking only at one particular camera. But if you are looking at multiple cameras, you have to select 3 or 4 or even all.

Generally, getting the backup is a relatively easy task, but it is better to get help from intelligent experts in this field of activity. The good news is getting backup is possible in the NVR system, so you don’t need to be worried about the deleted or lost videos.

 .

How do you access the lost or deleted videos in Dahua NVR?

This part will explain the detailed steps to recover smashed videos from Dahua NVR systems. It would help if you double-click to open the NVR video data recovery software.

You can use the top and best software module for NVR. It is time to start the process. In the first step, you have to know the image file of Dahua. Then, select the image file and select the partition.

Next, you can use deep analysis to detect the NVR brand. You will see the NVR spot list. Sometimes, as the user, you are unsure about the NVR brand, so you can click the analysis mode directly to recognize the NVR system.

Finally, you can find out the main program has recognized 2 possible brands for the available image file. Usually, you have to select the top one. Finally, click the demanded one and click the OK.

It is also possible to rename the task and click OK. You can overwrite the existing task if you have worked with these features before. Can you find out the detectable dates?

You can detect the demanded video within these available dates and then analyze them. It is also a good idea to check the analysis speed too. You have to wait until the analysis process is completed. The remaining time is available for you to see and observe.

Besides the recorded videos, you can also face the raw videos with extension names. Remember that you must wait because the whole process of analyzing and video carving is automatic. So you don’t need to do anything.

Check the log and the file window. After completing the analysis, you can switch to the file window and find all possible cameras and a long list of videos.

 .

How do we recover the deleted videos from the Dahua NVR system?

According to the previous part and the access method of recorded videos in the NVR system, recovering these lost videos will be relatively easy. You only need the analysis mode of the Dahua NVR system, and for this analyzing process, you have to use deep analysis.

If this step and process don’t work as you want, you can select the device and try the custom analysis to set up another task. You also can try to put a name with custom. To tell the difference between each task, like fast analysis, deep task, and custom task, you must know all the available options in the NVR system.

Usually, you can use the deep or custom task for the Dahua NVR system. Finally, you can switch back to the directory or log window. You will the witness of the almost complete progress.

The digital experts mostly use the online checksum, and they have the read-only option in the setting. You can tick the demanded one to ensure it is the original device with the read-only option.

Not any of the proper operations can affect the original devices. Another available option is adding checksum options. These features show why many people need digital engineers.

The standard data recovery engineers can help you if you find your lost video. Some users believe they don’t need the expert because ticking the other checksum options is much easier.

The analysis speed will become slower than the average speed. Finally, you can check channel one of your camera and see the recovered lost videos. You can also watch the preview video, which is useful and practical.

 .

How do we retrieve the deleted video from NVR?

Time is the main thing when trying to retrieve the deleted recorded video. Whenever you realize you have lost your videos, preventing the NVR from overwriting the deleted video is essential.

Note that recording and storing the new videos can decrease the chance of a successful retrieval. In addition, you have to check the backup storage. This feature can help you recover the lost or deleted video.

Some NVR systems have an automatic backup feature, which helps you retrieve lost and deleted videos. If you cannot recover the lost data, contact your NVR system’s technical support.

These experts can provide the best guidelines and information to retrieve your lost footage. You only need to share the details of your NVR system, its software version, and the type of video you lost.

There is another available option to retrieve the deleted video. You can use the recovery software of the NVR system. This software can support you retrieve the deleted video as soon as possible.

You must follow the instructions mentioned to utilize the software quickly and promptly. This software is compatible with the NVR system. It can also be practical in the installation process of the NVR system.

Don’t forget to get help from a professional assistant in this field of activity. These persons can help you in a unique process using the most advanced tools and devices.

Final thought

Deleting helpful videos from NVR can be harmful, mainly when the video contains important content. Based on the mentioned information, it is possible to recover and retrieve the deleted or lost videos from the NVR system.

This article has mentioned all the steps and processes of deleted video recovery. We also share some information about the backup process in the NVR system. You have to check the highlighted process and consider the chance of a recovery process.

Finally, retrieving is only sometimes an easy method for everyone, but you can experience the recovery process with the help of different available devices and options. Don’t worry about your deleted video; you can retrieve it easily via the NVR system. We’re Dahua UK Authorised partner providing Dahua products with the best price only for trade users.

.

<p>The post Can I retrieve deleted CCTV footage from my Dahua NVR first appeared on NVR IPCAMERA SECURITY.</p>

Troubleshoot Offline Camera

Troubleshoot Offline Camera

Learn how to troubleshoot when a new Verkada camera is offline

Updated over a week ago

Use this article to read through some common scenarios and try the suggested troubleshooting tips to help. If you still need help, please contact Verkada Support.

What is the LED status of the camera?

Camera has been solid orange for over 10 minutes

Camera is blinking blue for over 5 minutes

Camera is solid blue for over 5 minutes, says “waiting to be connected on Verkada Command”

Roles and Permissions for Cameras

Roles and Permissions for Cameras

Learn about the roles and permissions available for Verkada Cameras

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Cameras.

Org-level roles

Organization-level roles are configured on a per-user basis. Groups cannot be used to set organization-level roles.

Below, click the down arrow to the left of the role to learn more about the role and access.

Org Member

Org Admin

Verkada Cameras Troubleshooting 2024

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

CP52-E PTZ permissions

The CP52-E PTZ camera permissions determine who can manage the Sentry Mode feature.

Permissions model (example)

Here’s a simple example of a permissions model that a typical organization with several sites and users may employ:

Users and their required level of access

Permissions each user should be assigned

.

Set Org Admin permissions

Revoke Org Admin permissions

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Customize roles and permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

Roles and Permissions for Command

Roles and Permissions for Command

Learn about the roles and permissions available to Command users and groups

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Command. It also explains how to customize roles and permissions.

Permission levels

Permissions are set at the following levels:

Daha fazla göster

Permissions considerations

Common user permission configurations

Daha fazla göster

Roles and permissions by Verkada product

.

Org-level roles

Org-level roles are configured on a per-user basis. Groups cannot be used to set org-level roles.

Org member

Org Admin

Access Control Role

.

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

Access Site Admin

.

Customize Roles and Permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

FAQ

Why has my organization disappeared?

Why are cameras missing from my organization?

Why can’t I access certain features or settings, such as other users?

Resolve Issues with Missing Cameras

Resolve Issues with Missing Cameras

Learn how to resolve issues when cameras are missing from your Verkada account

Updated over a week ago

When you log in to Verkada Command, you can only access cameras and video in organizations or sites where your user account has permissions.

Note: Even if you are an Org Admin, you still need to grant yourself permission to view all sites. Learn more about roles and permissions for cameras and Command.

If you log in to Command and cameras are missing or have disappeared, always check user permissions. The most common reason cameras are not visible is that your user account needs permissions to the site(s) where the cameras are configured.

Common reasons that can cause cameras to disappear

Check permissions

If you are an Org Admin, you can check and correct your own permissions:

Resolve Issues with Night Mode

Resolve Issues with Night Mode

Common issues with IR and Night Mode with steps to resolve them

Updated over a week ago

Each Verkada camera has night vision capabilities, using a sensor to detect low-light situations. When external lighting is low, the camera switches to night mode and records in black and white, using infrared (IR) LEDs to illuminate the environment. If the IR is emitted improperly through the dome or reflected into the lens, it negatively impacts image quality.

Common night mode issues

It is imperative that the dome remain free of debris and the camera is installed properly to achieve the best image quality. When viewing footage in night mode if the footage appears obscured it is most likely the result of one of the following scenarios:

Camera always in night mode

If your camera is always in night mode even where there is sufficient light in the environment the lux (light) value may need to be adjusted. If this is the case, reach out to Verkada Support for further assistance.

Environmental obstruction

If the camera is mounted too close to a wall, ledge, or light source, the image quality may be degraded due to IR reflection.

Recommendation. Ensure that cameras are mounted sufficiently far away from surfaces that may cause the IRs to reflect, such as light sources.

IR obstruction

If a first-generation Dome camera (D30 or D50) is operating in night mode when there is plenty of light, the IR sensor is likely obstructed by the camera housing.

To fix the obstructed light sensor, physically rotate the lens barrel assembly 180° so the sensor and IRs are visible through the camera case.

Example: Proper and improper orientation

Note: After rotating the lens barrel, the camera orientation may need to be changed in Command.

<p>The post Verkada Cameras Troubleshooting 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Lorex Fusion: Download the Lorex App

The following article provides instructions for downloading the Lorex App and connecting your Lorex Fusion Collection recorder to the app.

Prerequisite

Before you start, your Fusion recorder must be powered on and connected to your router using the included Ethernet cable. For Basic System Setup instructions, refer to your Fusion recorder’s Quick Start Guide or Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

Download the Lorex App

Once your Fusion recorder has connected to the Lorex App, complete the final Fusion steps by connecting your Fusion Wi-Fi cameras and accessories.

For setup instructions using the new local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (New Local UI).

For setup instructions using the previous local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories.

Lorex Fusion: Frequently Asked Questions

The following frequently asked questions (FAQs) provide more information about your Lorex Fusion Collection. Where applicable, the FAQ includes links to articles where you may find more information.

Lorex Fusion Troubleshooting FAQ.

What is Lorex Fusion?

Our Lorex Fusion recorders incorporate the newest (fusion) technology to connect both Lorex Wired and Fusion Wi-Fi Cameras, Doorbells, Floodlights, and Sensors to one system. Lorex Fusion Wi-Fi Cameras and Accessories can connect to one recorder for continuous 24/7 recording and local, secure storage (up to 10TB). Everything can be accessed from your Lorex App for easy control of all devices.

.

Why do I get an offline message and a blank screen for the (B463AJ) 2K battery doorbell’s channel on the Fusion recorder?

Being a battery-operated doorbell, it will always go to sleep after a period of inactivity to conserve battery life. Once the doorbell is correctly paired to your Fusion recorder, the offline message means the doorbell has gone to sleep but is still connected and can be awakened. When motion is detected, or when the call button is pressed, there will be live video from that channel. You can also manually wake up the doorbell through the Lorex app, by activating the liveview.

.

Can my Battery Video Doorbell record continuously?

To conserve battery life, Wi-Fi Battery Video Doorbells only record when motion is detected. They do not record continuously.

.

Which recorders are part of Fusion?

For a list of Lorex Fusion Recorders, please refer to the Product Compatibility Chart.

.

Can I connect all Lorex Wi-Fi Cameras and Accessories to my Fusion recorder?

Only Lorex Fusion Compatible Wi-Fi Cameras and Accessories can connect to Lorex Fusion Recorders.

.

Which Lorex Wi-Fi Cameras and Accessories are part of Fusion?

See the following list of Lorex Fusion Wi-Fi devices:

.

Should I update my Lorex Fusion recorder’s firmware?

It is recommended to update your system firmware to the latest version to ensure remote connectivity and to support newly added Fusion Wi-Fi devices.

.

Does my Lorex Fusion recorder require a network setup?

Yes, a network setup is required to connect Fusion Wi-Fi cameras and accessories to your Fusion recorder. Ensure you connect the included Ethernet cable to your recorder’s LAN port and your router.

.

Does it matter which router I use?

Yes, due to its strong signal, the dual-band router is suitable for high resolution video recording and for connectivity between devices. Ensure that your Fusion Wi-Fi cameras and accessories and your Fusion recorder are all connected to a dual-band router (2.4 GHz/5 GHz bands).

.

How many Lorex Fusion Wi-Fi Cameras and Accessories can I connect to my Fusion recorder?

This depends on your Fusion recorder and the number of Fusion Wi-Fi channels it comes with. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

What is a Fusion Wi-Fi channel?

A Fusion Wi-Fi channel is the channel you use to add a single Fusion Wi-Fi camera to your system. A 16-channel security system with 8 PoE ports/channels (for wired camera connection) and 8 Fusion Wi-Fi channels means that 8 Fusion Wi-Fi cameras and accessories can connect to the entire system.

Note: Fusion Wi-Fi channel’s are only available on certain Lorex Fusion recorders. For a list of Fusion recorders, see the Product Compatibility Chart.

.

How many Fusion Wi-Fi channels are on my Lorex Fusion Recorder?

The number of Fusion Wi-Fi channels varies per Fusion recorder. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

How do I setup my Lorex Fusion system?

Complete your Fusion setup in the following order:

After connecting your Fusion system, ensure you adjust your Fusion settings.

.

Are there Fusion setup tutorial videos?

For a video walk-through of the Fusion setup with the new local UI (N845, N846, N847, N864, D863, D881 Series), please watch here.

For a video walk-through of the Fusion setup with the previous local UI (N841, N842, N843, N844, N861, D862, D871 Series), please watch here.

.

How do I setup my Lorex Fusion recorder and wired cameras?

For Basic System Setup instructions, refer to your recorder’s Quick Start Guide or Series Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

How do I connect my Lorex Fusion Wi-Fi camera or accessory to my Fusion recorder?

For full setup instructions, please click on the article corresponding with your model number.

.

Which password should I enter to connect my Lorex Fusion Wi-Fi camera or accessory to my Fusion recorder?

Enter the same password that you created in the Lorex App when setting up your Fusion Wi-Fi device.

.

What is continuous recording?

Once your Lorex Fusion Wi-Fi camera connects to your Fusion recorder, your camera’s recording settings are automatically set to continuous. This means that your Fusion Wi-Fi camera will record 24/7 or for the entire duration of the recording schedule onto your Fusion recorder’s hard drive. It is worth noting that recordings on the camera are limited due to the size of its onboard storage, while recordings on the recorder are extensive (3TB to 10TB). Continuous recording captures everything in the background, and you can playback to catch anything you missed.

.

Do all Lorex Fusion Wi-Fi cameras record continuously?

No, to conserve battery life, battery-operated video doorbells do not record continuously (24/7).

.

How do I set my Lorex Fusion Wi-Fi camera to continuous recording?

After Fusion setup, your Wi-Fi camera is automatically set to Continuous recording. To adjust your camera’s recording settings, login to your recorder and navigate to the devices menu. For instructions, please see the article Lorex Fusion: Adjust Settings.

Note: Battery-operated video doorbells do not record continuously (24/7). Being a battery-operated doorbell, it will always go to sleep after a period of inactivity to conserve battery life. Once the doorbell is correctly paired to your Fusion recorder, the offline message means the doorbell has gone to sleep but is still connected and can be awakened. When motion is detected, or when the call button is pressed, there will be live video from that channel. You can also manually wake up the doorbell through the Lorex app, by activating the liveview.

.

How come I’m receiving duplicate notifications in the Lorex App?

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder. For instructions, please see the article Lorex Fusion: Adjust Settings.

.

After Fusion setup, where is my Lorex Fusion Wi-Fi camera’s video footage being stored?

Your Lorex Fusion Wi-Fi camera saves recorded motion detection videos onto the local microSD card (not always included). Once you’ve connected your Fusion Wi-Fi camera to your Fusion recorder, your camera’s recording settings is automatically set to 24/7 Continuous recording, and all recorded video is stored on your recorder’s extensive hard drive (up to 10TB).

.

What features are supported in my Fusion recorder vs. the Lorex App?

Please see the following list of features supported in either your Fusion recorder and/or the Lorex App:

.

Can I use my web browser to access my Lorex Fusion Wi-Fi camera?

You can only access your camera on the Lorex App, recorder, or on the Lorex Cloud Client.

.

When modifying the password in the Lorex Cloud Client, which password should I enter?

Enter the password for your Wi-Fi camera or accessory created in the Lorex App during setup.

.

Where can I order the Lorex Fusion Collection?

To order, go to lorex.com.

Lorex Fusion: Troubleshooting

The following article provides some troubleshooting tips for setting up your Lorex Fusion Collection.

.

My Fusion Wi-Fi camera or accessory is not appearing in the device list.

.

My Fusion Wi-Fi camera or accessory is not connecting to my Fusion recorder.

• Give your Fusion Wi-Fi camera or accessory a few minutes to establish a connection.

• Check to see if your Fusion recorder has the most up-to-date firmware. New Local UI: Login to your recorder and navigate to System > Update & Reset > Upgrade, then click Check for Updates.  Previous Local UI: Login to your recorder and navigate to Main Menu > Information > Update/Reset > Update, then click Check for Updates. For instructions on updating your recorder’s firmware through USB, see the article How to manually upgrade the firmware of your recorder.

• Ensure that your Fusion Wi-Fi cameras and accessories and your Fusion recorder are powered on.

• The same password created for your Fusion Wi-Fi camera or accessory in the Lorex App must be entered in your Fusion recorder. If you have forgotten the password, then reset your Fusion Wi-Fi camera or accessory and connect it to the app again.

• (Applies to the previous local UI only) If your password for your Fusion Wi-Fi camera or accessory is entered incorrectly in your Fusion recorder, then your Wi-Fi device will lock itself. Reset your Fusion Wi-Fi camera or accessory and connect it to the app again.

• Ensure that you are entering the password for your Fusion Wi-Fi camera or accessory created in the Lorex App, and not the Lorex App account password. Those are two separate passwords.

• Ensure that your Fusion Wi-Fi camera or accessory is connected to a dual-band router (2.4 GHz/5 GHz bands).

• Ensure that you are connecting the Fusion Wi-Fi camera or accessory to an available Fusion Wi-Fi channel, and not a Wi-Fi channel that already has a Wi-Fi device connected to it.

.

I don’t know the password for my Fusion Wi-Fi camera or accessory.

If you don’t know the password for your Fusion Wi-Fi camera or accessory, then you will need to reset the device and connect it to the Lorex App again.

To reset your Fusion Wi-Fi camera or accessory:

.

I’m receiving duplicate notifications in the Lorex App.

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder. For instructions, please see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N910 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi Cameras and Accessories to your N910 Fusion recorder.

.

Our Lorex Fusion recorders incorporate the newest (fusion) technology to connect both wired and Wi-Fi cameras, doorbells, floodlights, and motion sensors to one system. All Fusion compatible Wi-Fi cameras and devices connect to one recorder for continuous 24/7 recording and private local storage. Access everything from the Lorex App for easy control of all devices.

Note: To conserve battery life, Wi-Fi Battery Video Doorbells only record when motion is detected. They do not record continuously.

For any connection issues, see the article Lorex Fusion: Troubleshooting.

.

Part One — Wired Setup

Setup your Fusion recorder and wired cameras. For Basic System Setup instructions, refer to your recorder’s Quick Start Guide or Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

Important: Network setup is required for your system — use the included Ethernet cable to connect your recorder to your router.

.

Part Two — Connecting your Lorex Fusion Wi-Fi Camera

Connect your Lorex Fusion Wi-Fi Camera to the app and then from your recorder scan your network to add it.

.

Option A — Connecting Your New Lorex Fusion Wi-Fi Camera to Your Recorder

Add compatible Lorex Fusion Wi-Fi Cameras and Accessories onto Fusion Wi-Fi channels on the recorder.

To connect your New Lorex Fusion Wi-Fi Camera to the recorder:

Note:

.

Option B — Connecting Your Existing Lorex Fusion Wi-Fi Camera to Your Recorder

Add compatible Lorex Fusion Wi-Fi cameras and accessories onto Fusion Wi-Fi channels on the recorder.

Note:

To enable remote viewing for the mobile app, you will need to:

To connect your Existing Fusion Wi-Fi camera to the recorder:

1.From the Live View display, click the pair icon  in the center of the Fusion Wi-Fi channel’s screen.

Note: It may take a few minutes for your Lorex Fusion Wi-Fi Camera’s video feed to appear.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N845, N846, N847, N864, D863, D881 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi cameras and accessories to the Lorex App and to your Fusion recorder.

Note: These Fusion instructions apply to the new local UI only. For Fusion instructions that apply to the previous local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories.

.

Before you start

.

Watch the Lorex Fusion setup tutorial video

For a video walk-through of the fusion setup, please watch here.

.

Connect your Fusion Wi-Fi cameras and accessories to the Lorex App

Follow the Lorex App steps to add your Lorex Fusion Wi-Fi cameras and accessories. Refer to your camera’s documentation at help.lorextechnology.com for detailed setup instructions. Search your camera’s model number to access the product support page.

Note:

2.In-app, tap the  icon to add your Wi-Fi camera.

.

Connect your Fusion Wi-Fi cameras and accessories to your Fusion recorder

Note: You can add one Wi-Fi camera or accessory to one Fusion Wi-Fi channel. The number of Fusion Wi-Fi channels varies per Fusion recorder. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

2.From the Live View display, click the pair icon  from the center of the Fusion Wi-Fi channel.

Note: If your Lorex Fusion recorder and Fusion Wi-Fi camera share the same password, then the devices will automatically connect without entering the password.

.

After successfully connecting to your Fusion recorder, your Fusion Wi-Fi camera or accessory connection status turns green. For any connection issues, see the article Lorex Fusion: Troubleshooting.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N841, N842, N843, N844, N861, D862, D871 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi cameras and accessories to the Lorex App and to your Fusion recorder.

Note: These Fusion instructions apply to the previous local UI only. For Fusion instructions that apply to the new local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (New Local UI).

.

Before you start

.

Watch the Lorex Fusion setup tutorial video

For a video walk-through of the Fusion setup, please watch here.

.

Connect your Fusion Wi-Fi cameras and accessories to the Lorex App

Follow the Lorex App steps to add your Lorex Fusion Wi-Fi cameras and accessories. Refer to your camera’s documentation at help.lorextechnology.com for detailed setup instructions. Search your camera’s model number to access the product support page.

Note:

2.In-app, tap the  icon to add your Wi-Fi camera.

.

Connect your Fusion Wi-Fi cameras and accessories to your Fusion recorder

Note:

After successfully connecting to your Fusion recorder, your Fusion Wi-Fi camera or accessory connection status turns green. For any connection issues, see the article Lorex Fusion: Troubleshooting.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Adjust Settings

The following article provides instructions for adjusting your Lorex Fusion Collection settings.

.

Turn off duplicate notifications

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder.

To turn off duplicate notifications:

2.Under your Fusion recorder, swipe left to find your Fusion Wi-Fi camera or accessory.

3.Tap on your Fusion Wi-Fi device’s notification icon .

.

.

Adjust the recording settings for your Fusion Wi-Fi camera or accessory

After Fusion setup, your Lorex Fusion Wi-Fi camera’s recording settings will automatically adjust to Continuous, recording 24/7 directly to your recorder’s hard disk drive.

To adjust the recording settings (new local UI):

To adjust the recording settings using the previous local UI, navigate to Main Menu > CAMERA > Recording > Recording and follow the same steps as above.

.

Set the recording schedule for your Fusion Wi-Fi camera or accessory

You can set a custom recording schedule according to your needs. For example, you can set the system to record continuously during business hours and record on motion detection only outside of business hours.

• Click-and-drag on each day to customize the recording schedule. The schedule is set up as a grid, with each block representing two hours.

• Click  beside 2 or more days to link schedules (). This allows you to quickly change multiple schedules at once.

• To make fine adjustments to a schedule, click . This will allow you to set exact start and end times for a schedule.

• To disable all recording of the selected type on the selected day, click .

To set the recording schedule using the previous local UI, navigate to Main Menu > STORAGE > Schedule and follow the same steps as above.

.

Link sensors to cameras

Once you’ve completed the Fusion setup, you can link motion and door/window sensors to any compatible camera, so that when the sensors are triggered the linked automatically cameras record.

.

To learn more about using your Lorex Fusion system, visit the Fusion page or refer to the Lorex Fusion: Frequently Asked Questions article.

.

<p>The post Lorex Fusion Troubleshooting FAQ first appeared on NVR IPCAMERA SECURITY.</p>

InVid Tech is here to help you succeed, and as a company, we pride ourselves on the level of personal service we offer. We have an experienced team based in the United States, including Sales, Customers Service, Marketing & Tech Support. Additionally, there is support for Latin American Countries.

Steps to Change Secure Series Camera Compression to H.264

The below steps are needed in order to connect your camera to the Secure 4ch NVR attached with your order.  Please log into camera first, default username is “admin” and default password are “1234567u”, from there it will prompt you to change, please do so and follow below steps.  If you do not do this first, the camera will not connect to the NVR.

SEC-BODYTEMPCAM1 Camera Configuration Guide

**Please Note:  Cameras Default IP address is 192.168.1.121.  IP Utility can be downloaded off our website here

• Log into the cameras web interface on Internet Explorer (IE), default username is “admin” and default password are “1234567u”. Make sure to download the new plugin. 

Note: close ALL browser tabs while installing the plugin.

• Parameter Configuration (Configuration/Human Thermometer/Parameter Configure)

◦ Enable face detection

◦ Draw the area according to the real scenario, there is a maximum of 8 areas supported. We usually use one detection area to cover where people could potentially appear in, recommended distance is 9 to 16 feet (3-5 meters) for capturing.

• Leave the Display Trace Info at “Mode 1”

• Show Detection Area, can turn On or Off

• For Confidence Coefficient, we suggest keeping the default value (Mid). It’s for the face matching level with the built-in algorithm.

• Area ID is for the selected areas if you choose more then one main area, up to 8 totals. We suggest keeping this at one and focusing on the main point of entrance.

• For Face Pixel Minimum and Maximum, we suggest keeping the default value (70/1000). Only faces in this range will be detected.

• There are two different Snapshot Modes: 

◦ Timing: ‘upload interval’ is associated with ‘timing’, camera will upload one picture every 5 seconds (Suggested).

◦ Optical: ‘snapshot count’ is associated with ‘optical’, camera will upload the best face picture in 5 seconds.

• For Upload Image Interval we suggest leaving at 5 seconds (1-10 second range).

• For Yaw Degree, Tilt Degree, Pitch Degree and OSD Overlay Snapshot, we suggest keeping as default.

• FTP Upload Image Matting and FTP Upload Whole Image are if you are using the camera as a standalone device, no CMS or NVR, and wish to save the facial snaps to an FTP.

• Temperature Parameters

• Enable this field and leave all as DEFAULT except LENGTH UNIT and MOUNT DISTANCE

◦ IF YOU SWITCH TO FAHRENHEIT THE FIELDS STILL STAY AS DEFAULT (Except Length/Mount Distance, mentioned above)

◦ DEPENDING ON THE SELECTION OF “LENGTH UNIT” (METERS/FEET), ALL DISTANCE FIELDS WILL BE CONSIDERED IN THOSE UNITS!

[IMPORTANT] Set the mount distance according to the real installation, whose value should be the horizontal distance from the detection area to the camera. 

Hit ‘apply’ to save the settings.

• Face Alarm Linkage

IF SWITCHED TO FAHRENHEIT YOU MUST ADJUST “ALARM TEMPERATURE”, 99.5-100.5F (Default Celsius is 37.30)[

• [IMPORTANT] Thermal Mapping (Configuration/Human Thermometer/Thermal Mapping)

◦ This step is mainly for matching the thermal image with the visible image, which can ensure the measurement accuracy.  The Black Body device (Infrared Calibrator) MUST be in the Field of View of the thermal image.  The thermal image is a FIXED LENS and is a smaller field of view then the standard image.

• There are eight groups of ID, and each group ID contains three points. If using One area, then you do not have to set groups 2-8.

• Pick out three points that you can clearly see in the thermal image, mark them with point1, point2 and point3.

• Find the three locations of the three points in the visible image and mark them with the same point numbers associated with those in thermal image.

◦ Note: Suggested to choose three points far away from one another, so the triangle of can cover 70% of the image.

• Hit ‘apply’ to save the settings.

• Test if the rectangle can correctly surround the face, and perfect it by adjusting the three points.

• Thermal calibration (Configuration/Human Thermometer/Thermal Calibration)

• Install the blackbody properly where the camera can see it (within the thermal image). The blackbody needs to be powered on for at least 20 mins to reach to a stable temperature.

◦ The Infrared Calibrator will ALWAYS display in CELSIUS; the stable temperature is ~40C

• Enable.

• If you turn on ‘Display Area Info’, the blackbody (Infrared Calibrator) will also be shown with temperature on thermal image.

◦ Draw box around your calibrator

• Target Temperature: If using Celsius leave as 40C, if using Fahrenheit change to 104F (Default)

• For Distance, put the real installation distance between the camera and Black Body (Infrared Calibrator). No more then 9-16 feet (3-5 meters).  Distance is in Meters or Feet, depending what you selected under the Parameter Config menu.

• Keep the ‘Emission Rate’ as the default value.

• Hit ‘apply’ to save the settings.

InVidTech Secure Series Setup Guide v1

Also Read : How To Setup O-KAM Pro camera

SEC BODYTEMPCAM1 camera run off of POE output?

Yes it is, safe.

What are the minimum specs required to handle SEC-BODYTEMPCAM1?

For a single camera: i7 processing, at least 8GB of RAM.

From where is the temperature being scanned?

From a point in the middle of the forehead, the temperature is scanned, above the nose and in-between the eyes. If the camera captures a profile image it is using the skin around the earhole for temperature.  It is important to note that what is being scanned is skin temperature and not core temperature.

Should people be screened prior to entry?

The camera needs to be set within a controlled environment and cannot be installed outside. The calibrator isn’t weatherproof (IP66) and airflow, whether inside or out, could throw off the camera’s calibration.

If you need to screen people before entering the building, you would need to set up an enclosed tent to scan individuals. The camera can operate in both extreme heat and cold as long as no airflow would skew the results. If an individual is outside for an extended period, in the intense heat or cold without the opportunity to reregulate their temperature, the results might be slightly off, its recommended to wait 20-30 seconds before reading.

Need to wait when coming from outside for accurate reading?

Most of the time, there will not be any accuracy issues when getting scanned. If you have been out in the extreme heat or cold for an extended time you may want someone to wait roughly 30 seconds for their body to adjust to the environment. The camera is taking the skin temperature, which the human body keeps in check very efficiently.

What is your advice for poorly controlled environments?

If you are going to invest in the product, you will also need to invest in creating a controlled environment. If the environment is not controlled, you will not have accuracy. 

What effects an individuals’ temperature?

An individuals’ temperature will not read higher based on wearing a darker colored cap or clothing. The temperature scanned is the skin. The camera is using the face detection analytic to detect a human face then apply the algorithm built into the camera to display a temperature that is read from the epidermis of the forehead, or if it is a profile picture captured, the skin around the earhole is used.

If you’re wearing a mask, glasses, hood, hat, or all combined, if those two focal points aren’t blocked, then the camera can give a temperature reading.

Depending on the type of hat, for example, a forwards facing baseball cap pulled down entirely over the forehead can cause an individual not to be scanned. Another factor that could affect the scan is how the camera is mounted. The cameras must not be mounted higher than 8-feet. If the camera is wall-mounted and facing on a downward angle where a hat or hardhat is blocking the forehead, a solution would be to mount the cameras on a tripod to get a more direct shot.

Please watch the scenario video here for more info on this.

As for individuals who have been out in the extreme heat or cold for an extended time you may want to wait about 30 seconds for their body to adjust to the environment. The camera is taking the skin temperature, which the human body keeps in check very efficiently.

Two real-life examples of cold and hot temperatures:

In New York, the temperatures were averaging 45 degrees, and we had someone whose drive into work took about 20 minutes. While driving, they had the window rolled down and the air continually blowing into their face. They would walk from their car to the office and could feel their skin was cold. When walking into the office, they would get scanned, and their temperature would be between 96.9 and 97 Degrees. After waiting for about 60 seconds, they would rescan, and their temperature would average the mid 97 degrees.

In Arizona, where the temperature was over 100 degrees, we found that when someone was outside for a while, a cooling down about 20-30 seconds was necessary. Initially, their temperature registered at about 102, but after 20 seconds, it stabilized and showed their baseline temperature.

Something to keep in mind is that everyone is different. Two people who are excessively overheated may vary slightly in how fast their bodies regulated their temperature. One person might take about 10 seconds, while another person might take about 45 seconds. We are finding that the average is about 20-30 seconds for someone to regulate back to their baseline skin temperature.

Does the subject have to face the camera?

The subjects face must hit the 7% FOV (Field of View) mark of the camera to get an accurate reading. It is looking for two measurement points. The first point is in the middle of the forehead, roughly the area in-between the two eyes, near the nose, and if it captures a profile image, it is looking for the skin around the ear hole. The person has to be walking into the view of the camera and not away.

What is the ETA on the Fahrenheit firmware fix for US sites?

The firmware is currently available, giving the option for Fahrenheit or Celsius. The product leaves our warehouse with this latest firmware update, and the product comes defaulted to Fahrenheit & Distance comes defaulted to Feet with the option for metric units. 

What VMS’s are supported?

As of today 4/29/20, we know Axxon and EXACT are working on an integration. Other companies that have reached out but are not 100% confirmed yet. The SDK is available upon request but each is responsible for their integration. 

Without an NVR, will images be stored?

No. The camera will not store any images. 

Will the camera do face recognition without an NVR or computer?

The camera only does face detection. The CMS is what handles Facial Recognition if you aren’t running the CMS, face images will not be saved.

Will the camera track a person?

Tracking is based on facial detection. As soon as the 7% mark is met (7% is the required amount to get a temperature), it will read the face detection analytic and then apply the algorithm for the temperature display.  

Where are these cameras made?

The cameras are manufactured in China but are not affiliated with and are not OEM made products from Hikvision or Dahua. 

Can the camera just be connected to a LAN that has the NVR on it?

Yes, it can be stand alone.

What is the accuracy of the camera?

The accuracy of the camera is 0.54 Degrees Fahrenheit / 0.3 Degrees Celsius.   

Is this camera FDA approved for taking Body Temperature readings?

We are currently in the process of working on our 510k Certificate approval. 

Will the camera pick up the temp of a person who is walking away?

No. it is not designed to work this way.  Depending on the angle, it might be able to capture a profile and on occasion provide a temperature. 

Is there a max mounting height from the floor?

Yes, you may not exceed 8 feet from the floor when installing on a wall or ceiling mount.

How do you calibrate the calibrator?

Let the calibrator run for about 15-20 minutes. On the back panel of the calibrator, you will see a display. The display will be in Celsius regardless of the settings in the camera and CMS. Once the screen hits the 40-40.2 degrees, the unit has been calibrated. 

Can you set the camera and calibrator to shoot through a glass door?

 No, the camera and calibrator must be in sight of one another and cannot see through a glass window or door. There can be no glass between the devices and the subject. 

How far away does the calibrator need to be from the camera?

The camera and calibrator must be in view of each other and must not exceed 16 Feet. The recommended distance is 7-16ft. and the calibrator must be in the field of view of the THERMAL image

Does each camera require its own calibrator?

Yes, each camera requires its own calibrator. You cannot use two cameras with a single calibrator. The temperatures will not be accurate. 

Can you connect the CMS to a customer’s network?

Yes, the CMS can be connected to a customer’s pc and also run on a pc that is not on the network.

What does CMS stand for?

Central Monitoring Software

Is the CMS included with the purchase of camera & calibration device?

Yes, there is a free download that is available on our website. There is no charge. You can find it here

How many users can log into the CMS simultaneously?

The CMS (Central Management System) is stand-alone. You can install it on multiple computers, but there is a max of 10-user connections for each camera.  

CMS (Central Management Software) for PC

CMS for PC

This is the free CMS (Central Management Software) for the Secure Series for those using a PC. It will work with Secure Series Products. 

New in this Version:
.

Version V1.8.163.0.0.51.0_build 20240206

User Name: admin
Password: 1234567u

Download Secure CMS Here

Download AD (Active Directory) Instructions Here

IP Tool Utility for PC

This is the free IP utility for the Secure Series for those using a PC. It is used to find IP Cameras on the network and change the IP info (IP Address, Sub-Net, Default Gateway) of those devices. Version v1.9.9

Supported Devices: Secure NVRs, Secure IPCs

Download IP Tool Here

If you are using a computer, will it record video without an NVR?

No, the closest workaround is to add the camera to the CMS. The CMS saves snapshots based on facial recognition. Please keep in mind that if the CMS doesn’t see specific points of a face to realize its a face (such as if the person is partially covered), you may still get a temperature read, but the face snap may not save. The CMS is only saving snapshots, not video.

How to use a cloud feature in the NVR menu?

The cloud feature will be implemented in the future. Once it is fully functional, we will have additional information posted!

How many hours of video can be stored on the NVR?

That will depend on the size of the drive you put in the unit and the number of cameras you have installed. The standard 4-channel unit can house a single hard drive bay, and can use drives ranging from 1-10 Terabytes. 

Can the NVR do the job of counting and temperature notification?

No.

Will camera send notifications automatically without an NVR?

If the camera is networked, email notifications can be sent out, even without an NVR. This will include a snapshot with the temperature for individuals who are above the threshold set. The camera also has two alarm outputs that can be utilized.

To use the app, InVid LIVE CMS, the camera would need to be added to the CMS, and the CMS would have to be kept open and running on a PC. If a temperature over the threshold is registered, it will send a push notification to the app.

Is the NVR required for sending email alerts?

No, the camera can send out email alerts. The 4/8/16 Channel NVR does not have the ability to send out email alerts while the 32 channel unit does, for over temperatures.

What type of notifications are triggered by high temp?

You can have an email notification with a snapshot of the individual and temperature range and also the option of one or two sirens if the temperature is above the threshold. 

Are there any onboard relays that could be triggered to send an alert

Yes, the camera has 2-alarm outputs. Power is needed, 12/24 volt AC/DC. Settings within the camera can be configured to trigger an alert when a temperature is over the threshold. 

Can the system send email and text alarms?

The system can send emails, it includes the picture of the scene with the temperature reading. Currently, there are no text alarms, but it is something we are looking at trying to implement.

Audible alarm once it detects a high temp?

The camera has two notification functions. The first is an email notification. The second is an alarm output trigger. The CMS that links to the camera does have an audible alarm if your computer is set up for sound. 

What is the warranty on the Secure Series products?

Camera: 1-Year

Calibrator: 1-Year

NVRs: 2-Year on Unit & 2-Years on Hard Drives

.

<p>The post InVidTech Secure Series Setup Guide v1 first appeared on NVR IPCAMERA SECURITY.</p>

WiFi Camera 3rd Gen setup via Green Feathers app

This guide shows you how to set up your WiFi Bird Box Camera, Solar Powered WiFi Camera, or Garden Wildlife Camera on WiFi

.

Before you begin

Test the WiFi signal strength by taking your smartphone/tablet to the site where you plan to install your camera; if it has a weak signal at the installation site then the camera may struggle to maintain a connection (see section 9 Hints & Tips at the bottom of the guide for help with WiFi signal strength)
.

Insert a micro SD card if you have one; hold the camera with the lens facing up, then insert the micro SD card with the metal contacts facing up. Push it in fully until you feel it click into place. If you have trouble inserting the SD card to the point where it clicks into place, hold it down with your thumb then use a thin object like a pen to push it down fully
.

Before you mount the camera in the bird box, make sure it’s connected to your WiFi router and can be viewed on the app. It’s best to set the camera up when it’s plugged in a different room to your router, then once it’s connected you can unplug it and install it in the final location

Ensure the device being used to set up the camera is connected to the same WiFi network that you want the camera to be connected to (this is only required for the setup process)

Make sure you know the name and password of the WiFi network which the camera will be connected to

Make sure that you are connecting the camera to a 2.4GHz WiFi signal; if you don’t know what this is you can read more here
.

Plug in the power supply into the trailing cable of the camera; after the camera has powered on you will hear a three note chime, and the camera will start saying “Wait for WiFi config”

Remove the lens cap on the camera, if it has one, and remove the cap on the reset button 
.

.

Download the Green Feathers app for Android from the Google Play store by clicking here.

Download the Green Feathers app for iOS from the App store by clicking here.

Let’s get started

To get started, open the app:

.

1. Registering an account

Tap ‘Sign Up’ to create an account, then select ‘Agree’ for the ‘User Agreement and Privacy Policy’. If you have already signed up then skip below to the section called ‘Adding the camera to the app’.

.

.

Once your account is all setup, just log in to the app!
.

2. Adding the camera to the app

The first time you go to the Home page, you can choose to allow the app to use your device location. This is not essential, but helps with some features. Next, click the green ‘+’ icon at the top right of the screen.

..

Now select the model of camera you are setting up, then select “QR mode”:

.

.

3. Setting to QR mode and resetting the camera

Follow the instructions on the app or below to reset the camera.
.

Now tick ‘Next step’ and select ‘Next’.
.

.

4. Entering the WiFi details

Now you need to enter the details of the WiFi network that you want the camera to connect to. The name of the WiFi network which your phone or tablet is connected to should be automatically filled in, so just enter the password. To change the WiFi network your device is connected to, tap the icon to the right of the WiFi name:

.

5. Scanning the QR code

When you select ‘Next’, the app will display a QR code to you. Point the camera 15-20cm away from the QR code, directly facing the screen, and the camera should register it and say ‘Connect router’. When it says this, tap the ‘I Heard a Prompt’ button.

If the camera is not scanning the QR code, try slowly increasing or decreasing the distance between the camera and phone screen to bring the QR code into focus. It can sometimes be easier with the phone placed on a flat surface to help keep the camera pointed in the right direction while slowly moving it.

It is also possible to re-adjust the focus on the lens which can be done by gently twisting it. The nut around the bottom of the lens will need loosening first. It is best to adjust the lens a small amount at a time as it shouldn’t be far out of focus.

After you have tapped the ‘I Heard a Prompt’ button, the app should automatically begin connecting to the camera. 
.

.

After a minute or so, it should have found the camera and added it to the app, you can set a name for the camera now, or later on in the settings menu.

.

6. Troubleshooting

If the camera does not connect to your WiFi:

.

If you have connected it to your internet router, but it shows the message ‘Establishing encrypted channel‘ and doesn’t load: 

Remember, this guide only applies to the 3rd Gen NCIP3WF which was released in December 2020, if you have an older model of the camera have a look at our guide for the NCIP9WF or for the NCIP2WF. If you are unsure which camera you have, have a look at this article.

.

7. Adding and renaming the camera

Now you can rename the camera by tapping the pencil icon to the right of the camera name. Once it is added, to view the camera go back to the ‘Home’ page using the icon at the bottom left then select your camera from the list.

.

.

To view the camera go back to the ‘Home’ page using the icon at the bottom left then select your camera from the list.

.

To do next

Getting started with your Solar Powered Battery Camera

To view the settings for the camera, select the pencil and paper icon at the top right of the camera live feed. To find out more about the settings, have a look at this guide.

To read about the motion detection settings, have a look at this guide.

If you want to get the device added to other phones, tablets or computers, you won’t need to go through this process again, just follow this guide to get it done in a few minutes.

For a list of all the useful guides we have for this camera, you can look here.

.

Hints & Tips

Wired Bird Box Camera 3rd Gen setup via Green Feathers app

This guide only applies to 3rd Gen Green Feathers Wired Bird Box camera (GFIP3) or Garden Wildlife camera (GFIP320BWF) when not using WiFi

If you are unsure which model of camera you have, have a look at this article.

Before you begin

.

Download the Green Feathers app for Android from the Google Play store by clicking here.

Download the Green Feathers app for iOS from the App store by clicking here.

.

Let’s get started

To get started, open the app:

1. Registering an account

.

Once your account is all set up, just log in to the app!
.

.

2. Selecting the connection method

On the Home page, click the green ‘+’ icon at the top right of the screen.

Select the type of camera that you have from the grid shown, for wired setup it will either be Garden Wildlife Camera or Wired Bird Box Camera.

.

.

Now select Ethernet mode and follow through the prompts that show on the screen to connect your camera.

.

.

The app will start searching for your camera with a 2minute count down, once it has been found you will be presented with the screen below.

Once the circle has filled and the camera is connected to the network, you can set a name for the camera by tapping on it.

If the camera does not connect at this stage, try going through the wired setup steps again without resetting the camera.

.

4. To do next

To view the settings for the camera, select the pencil and paper icon at the top right of the camera live feed. To see the meanings of the settings, have a look at this guide.

If you want to get the device easily added to other phones, tablets or computers, you won’t need to go through this process again, just follow this guide to get it done in a few minutes!

.

5. Resetting the camera

1. Power on the device and wait for it to play three notes to indicate it has started up
2. Press and hold the reset button for 5 seconds; you will hear it say ‘Reset, camera reboot’.
3. When the camera starts saying ‘Wait for Wi-Fi config’ or has a flashing red indicator light, tick ‘Next step’. Once your camera has been reset you can re-connect it to Wi-Fi.

.

<p>The post Green Feathers 3rd Gen Camera Setup Guide first appeared on NVR IPCAMERA SECURITY.</p>

ATTENTION: Prior to purchasing and installing an accessory antenna, read the product specifications of your receiver to determine if your receiver has a weatherproof housing. Installing your weatherproof receiver outdoors provides a better line-of-sight between the receiver and the camera, increasing the strength of the wireless signal. See your product specifications to determine the weatherproof rating of your receiver.

The Directional Wireless Panel Antenna and the Omni-Directional Antenna are used to extend the range of one or multiple wireless or wire-free cameras.

Directional Wireless Panel Antenna (ACCANTD9)

Omni-Directional Antenna (ACCANTO8)

Use the 2.4GHz Directional Wireless Panel Antenna (ACCANTD9) to focus a wireless signal onto one specific wireless device (camera or receiver) to increase the range of transmission. A clear line-of-sight between the antenna and the wireless device needing range extension is required.

Use the 2.4GHz Omni-Directional Antenna (ACCANTO8) to enhance the signal of one or multiple cameras that are paired to a single or dual antenna receiver. You may also use two Omni-Directional Antennas to extend the range of all cameras paired to a dual antenna receiver.

REQUIREMENT: To connect the antenna directly to the camera or receiver, the device must have a removable SMA type antenna. Visit www.lorextechnology.com/compatibility to ensure the antenna is compatible with your camera or receiver model.

Lorex Wireless Cameras and Monitors guide 2024

Also Read  : Lorex Camera Troubleshooting

Recommended Antenna Installation Methods

Your antenna needs will vary depending on the setup of your camera system, the number of cameras that require range extension, and the number of channels on your wireless receiver. Review the scenarios below to ensure you have the correct antenna and installation method to meet your needs.

Click a setup scenario to see the recommended installation method:

Combining Accessory Antennas

If you have installed your accessory antenna according to the recommended installation methods and would like to enhance wireless signal strength even further, you may add an additional Directional Wireless Panel Antenna (ACCANTD9) directly to a camera. The additional Directional Wireless Panel Antenna can be used with a Directional Wireless Panel Antenna or with an Omni-Directional Antenna attached to the receiver.

Click an antenna combination to see recommended installation methods:

Scenario 1: Extend the range of one camera paired to a single antenna receiver

To extend the range of one camera connected to a single channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9).

The Directional Wireless Panel Antenna can be connected in two configurations.

Configuration 1. Connect the antenna directly to the camera

Configuration 2. Connect the antenna directly to the wireless receiver

REQUIREMENT: The antenna connects using an SMA cable and replaces the existing antenna on either the camera or wireless receiver. Check www.lorextechnology.com/compatibility to determine if your product is compatible with the antennas.

Scenario 2: Extend the range of one camera paired to a dual antenna receiver

To extend the range of one camera connected to a multi-channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9). Connect the Directional Wireless Panel Antenna directly to the camera.

Scenario 3: Extend the range of select cameras paired to a dual antenna receiver

To extend the range of select cameras on a multi-channel receiver, use the Omni-Directional Antenna (ACCANTO8).

Connect the Omni-Directional Antenna to one of the antenna ports on the wireless receiver.

REMINDER: Each antenna port on a dual antenna receiver is associated with specific camera channels. One antenna communicates with odd numbered channels (1, 3, and 5), while the other antenna communicates with even numbered channels (2, 4, and 6). See the table below for dual antenna channel configurations.

If you connect the Omni-Directional Antenna to an antenna port and your wireless signal does not improve, try switching the Omni-Directional Antenna to the other antenna port or pairing your camera to a different camera channel.

Scenario 4: Extend the range of all cameras paired to a dual antenna receiver

To extend the range of all cameras on a dual antenna receiver, connect an Omni-Directional Antenna (ACCANTO8) to each antenna port on the receiver.

IMPORTANT: Two Omni-Directional Antennas are required to accommodate this setup.

Combination 1: Combine two Directional Wireless Panel Antennas

If you are using a Directional Wireless Panel Antenna (ACCANTD9) to enhance the signal of a single camera with a single channel receiver, you can use an additional Directional Wireless Panel Antenna to further enhance the wireless signal.

Connect one Directional Wireless Panel Antenna directly to the camera and one Directional Wireless Panel Antenna directly to the wireless receiver. To maximize signal strength, it is recommended to aim the two antennas directly at each other with a clear line-of-sight.

Combination 2: Combine a Directional Wireless Panel Antenna with an Omni-Directional Antenna

If you are using an Omni-Directional Antenna (ACCANTO8) to enhance the signal of multiple cameras, you can further enhance the signal of a specific camera by connecting a Directional Wireless Panel Antenna (ACCANTD9) directly to the camera.

A clear line-of-sight between the Directional Wireless Panel Antenna and the Omni-Directional Antenna is recommended to maximize signal strength.

Lorex SD Pro App: Changing / resetting the password

If the password for the Lorex SD Pro app to view the Wireless Home Monitor is lost or forgotten it will need to be reset.

To reset the Lorex SD Pro app password:

1.Ensure that your Wireless Home Monitor is connected to a network router using the included Ethernet cable.

2.On the Wireless Home Monitor tap the Menu icon ().

3.Use the joystick to select Settings > Network > Reset Password.

4.Select Yes to confirm.

5.Tap the Menu icon () repeatedly until all the menus are closed.

6.Launch the SD Pro app and enter the default password. Refer to your user manual for your default password. You will be prompted to create a new password.

Lorex SD Pro App: Setting up Wireless Home Monitor remote access

You can access and view wireless cameras from a Wireless Home Monitor system using an iPhone, iPad, or Android smartphone or tablet using the Lorex SD Pro app. It is available at the App Store or Google Play Store.

Prerequisites:

To set up the mobile application:

LW2700 Wireless Home Monitor: Included cables and accessories

LW2700 Series Wireless Home Monitors support wireless cameras using a wireless signal. They do not have an internal battery and require a connection to a power source. Refer to your user manual for model specific information on cables and accessories. Click here for downloads and documentation for your product.

Most wireless home monitors include the following cable connections and accessories when purchased:

Network: Wireless camera Internet requirements

Standard wireless cameras that connect to a DVR / NVR, do not need access to the Internet to function. Stand-alone IP cameras do not require an Internet connection for basic functions, but an Internet connection is required for full functionality.

Security Cameras: Understanding Field of View (FOV)

Field of View (FOV) is the maximum observable area that is seen at any given moment through an optical device such as a camera lens. The coverage of the area can be measured using the horizontal and vertical distances to find the diagonal of the area in degrees. Mathematically, the FOV is calculated using the horizontal dimension of the sensor (h) and the Focal Length (F).

You can find the camera’s Field of View details in the Specifications sheet. Click here for additional support content including security camera documentation.

The Camera Lens, Sensor and Focal Length

Focal length (F) is the distance between the center of a lens and its sensor. The size of the lens is the aperture size.

These factors affect field of view. A narrower focal length captures more of the scene and displays a larger field of view. A wider focal length magnifies a scene and decreases the field of view. The higher the focal length value the lower the FOV.

Types of Camera Lenses

Fixed: a fixed camera focal length provides an Angular FOV which is permanently set and cannot be adjusted by the user. Varifocal: the camera focal length can be manually adjusted by the user. Generally, this is done manually with screws or dials. At Lorex we have motorized varifocal cameras that allow you to digitally zoom using your phone or NVR without losing details. These lenses provide flexibility and customization for your camera image needs.

The importance of Field of View

A wide angle lens or smaller lenses produce a greater field of view and captures more objects in a scene enhancing your ability to cover larger and wider areas such as foyers, parking lots or warehouses.

A narrow angle lens or larger lenses produce a smaller field of view; capturing a limited area, but the camera quality image improves in detail. These are designed to monitor a specific object, such as cash registers, entrances/exits, hallways or objects of value.

How to Calculate the FOV

To calculate the FOV requires the sensor size and the focal length of the lens: h = Sensor Size F = Focal Length of the Lens

FOV is represented by this equation: FOV = 2tan-1(h) / 2F

Example: h = 4.7mm F = 6mm FOV = 2tan-1(h) / 2F = 2tan-1(4.7)(12) = 2tan-1(0.39) = 2(21.4°) = 42.8°

W482CAD – 2K Wi-Fi Camera : Frequently Asked Questions

The following FAQ article answers many of the general questions about the 2K Wi-Fi Camera with Smart Deterrence (W482CAD). Where applicable, the FAQ includes links to articles where you may find more information.

.

Where do I place my Lorex 2K Wi-Fi Camera?

.

How should I position my Lorex 2K Wi-Fi camera?

When mounting the camera on a wall, make sure of the following:

 Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

.

How do I enable motion detection and person detection?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap  icon to enable Motion Detection.

Note: If motion detection is disabled, general/person/vehicle detection will automatically disable and you will not receive any motion detection notifications in the Lorex App.

.

How do I customize Motion Zones™?

Motion Zones™ allows you to customize your device’s motion detection region. Motion Zones™ screen consists of the following settings:

To set Motion Zones™

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap Motion Zones™.

 For full instructions on how to set customized Motion Zones™, see Configuring Motion Zones™.

.

Why am I receiving so many notifications?

There are a few ways you can lower the number of notifications you are getting.

.

How do I enable Color Night Vision?

1.Lauch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap  icon to disable Auto Night Vision.
Note: Disabling Auto Night Vision will force the camera into Color Night Vision mode. Recommended in low-light conditions.

.

How to activate Two-Step Verification?

1.Launch the Lorex App.

2.Tap Settings.

3.Tap Account Settings.

4.Tap Two-Step Verification.

5.Tapicon to enable Two-Step Verification.

For detailed setup instructions, see Two-Step Verification Setup.

.

How to optimize video quality?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Video Settings.

4.Tap  icon to enable HDR (High Dynamic Range).

Note: Enabling HDR optimizes video picture in high-contrast conditions such as under-lit and over-lit areas.
By default, the video quality is set to High (2x1080p HD).

.

What is Home & Away™?

Lorex App can automatically use your location to manage your notifications when you are at home or away. The app will notify you when you are inside/outside of your set home perimeter.

To start using this feature, navigate to your mobile device settings and enable Location services for Lorex App.

For detailed setup instructions, see Configuring Home & Away™.

.

How do I activate the LED deterrence light when motion is detected?

1.Lauch Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Deterrence Light Brightness.

4.Tap  icon to enable camera’s deterrence light whenever motion or person is detected.

.

How do I remove the 2K Wi-Fi Camera from my account?

1.Launch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Remove Device.

.

How to permanently delete data of 2K Wi-Fi Camera?

Refer to Formatting Device Storage for more information.

.

Does my device support WPA2 or WPA3?

Your device supports Wi-Fi Protected Access 2 (WPA2) which is the industry standard security protocol for Wi-Fi networks. WPA2 offers security against unauthorized access and data interception and is supported by most Wi-Fi routers including those that support both WPA2 and WPA3. It employs Advanced Encryption Standard (AES), an encryption mechanism, which secures communication between your camera and Wi-Fi network to keep transmitted data confidential. For information on which devices support WPA2 and which devices support WPA3, please refer to “WPA2 and WPA3 Supportive Devices.”

.

What are the compatible SD cards?

Refer to Compatible SD Cards and Storage Sizes for more information.

.

What devices are compatible with the 2K Wi-Fi camera?

Refer to Product Compatibility Chart for more information.

W482CAD – 2K Wi-Fi Camera : Installation

This article provides instructions to install your Lorex 2K Wi-Fi camera with Smart Deterrence (W482CAD).

.

What is included in the box?

The above contents are based on one camera.

.

How to connect with Lorex App

3.Open the Lorex App app and create an account or login with your credentials.

4.Tap  icon to add a new device, then follow the in-app instructions to complete the device setup.

For full instructions on Lorex App setup, see Connecting with Lorex App.

.

How to mount 2K Wi-Fi Camera to the wall

.

How to mount 2K Wi-Fi Camera to the ceiling

Wi-Fi Security Cameras – How to Read a MicroSD card

To view the contents of a MicroSD card on a laptop or computer, follow these steps:

a. Select the day to play back:

b. Click on the available folder:

c. Within the folder, click either the day folder (Video files) or the jpg folder (Snapshots):

d. Click to select a video time from 00 – 23 hours:

6.Click the MP4 video file to view the video. 

Wireless Home Monitor: Audio not working

If the audio is not working on your Wireless Home Monitor:

• Ensure that the protective film is removed from the camera lens.

• Ensure that the monitor volume is not muted. A mute icon () will be visible on the screen if the volume has been muted.

• Turn the monitor volume up using the volume buttons on the side of the unit. Location will vary by model. For exact location of volume buttons for your model, refer to your user manual. Click here for downloads and documentation for your product.

• The camera must be in Full Screen mode for audio. Tap the Channel Select icon () to switch between channels in Full Screen mode. Audio is disabled in Quad mode.

If audio is not working after increasing the volume and viewing in Full Screen mode, restore the system to default settings.

To restore your monitor to default settings:

CAUTION: Restoring to default settings will erase any setting input on the monitor. Your monitor will need to be reconfigured.

1.On the monitor tap the Menu icon ().

2.Use the joystick to select Settings > Default Settings.

3.Select Yes.

.

<p>The post Lorex Wireless Cameras and Monitors guide 2024 first appeared on NVR IPCAMERA SECURITY.</p>

These setup discrepancies often translate into unreliable readings and missed opportunities, rendering the system less effective in its primary task of accurate number plate recognition. The good news is that with proper optimization, these systems can be significantly improved. In this comprehensive guide, we will explore practical methods to enhance ANPR accuracy with best practices for camera setup.

Whether you are a seasoned professional or an enthusiastic beginner, these techniques will enable you to maximize the potential of your ANPR system, ensuring precise and reliable results. 

The Basics of ANPR Technology

ANPR technology is a sophisticated system designed to automatically capture and interpret license plates on vehicles. By leveraging advanced algorithms and optical character recognition (OCR) technology, ANPR systems can rapidly analyze images or video frames, extract license plate information, and convert it into readable digital data. 

In other countries, ANPR is also referred to as Automatic License Plate Recognition (ALPR) and, simply, License Plate Recognition (LPR). 

Here’s a breakdown of the key components of ANPR technology:

Components of an ANPR System

Understanding these fundamental components is essential for users aiming to optimize their ANPR systems. With a clear grasp of the technology’s basic principles, individuals can proceed to implement the necessary adjustments and enhancements for improved accuracy and reliability.

Best ANPR Camera System Setup

Read More : How To Install Synology Surveillance Station

Factors Impacting Your ANPR Camera Setup

There are a number of fundamental components that make any ANPR Camera setup successful. These include:

Of these three, we see that camera setup holds the most potential for improvement for businesses and consumers to significantly bolster their ANPR results. We draw this conclusion because we know that our Plate Recognizer ANPR engine has been thoroughly tested and optimized to handle blurry, low-resolution, and dark images as well as other aspects of the real-world environment.  Feel free to reference the results of our ALPR benchmarking exercise. 

Further, counter to claims from camera manufacturers, we see that a modest, mid-range or even low-end IP camera performs just as well as a high-end, expensive camera.  Of course, no LPR camera vendor is going to admit this because they need a way to justify their existence.  As a side note, we even have customers running our software with existing CCTV cameras.

From our years of experience supporting and helping clients troubleshoot their license plate recognition systems, we have observed how the proper camera setup along with a strong ANPR engine can be an effective solution to detect and decode vehicle license plates.  This article offers specific tips and suggestions on how to best set up your camera to maximize your ANPR.

Before You Begin, an Important Note

With your ANPR Camera Setup, please keep in mind that if your eyes can easily read a license plate through the camera, our ANPR engine can too. However, if you’re squinting and struggling to see the license plates, our engine might find it challenging as well. Visual clarity is the key. A clear view means accurate reads.

Camera Zoom For The Best ANPR Systems

When it comes to zooming the camera for best ANPR, it is important to avoid having a high-level view of the overall parking lot or site.  This is called under-zooming, where the camera is capturing an overall wide-angle view of the landscape.  So the above two images are not set up correctly for best ANPR results.

For beginners handling license plate recognition, there is a common misconception that a wide-angle shot is the best.  Cameras will seek to aim wide across parking lots rather than towards entrance or exit points which allow them to truly pick up plates and get a good read. 

To address this, adjust the camera positioning and zoom in on the ingress and egress areas of the parking lot.  Rather than have a wide-angle view of the street with all the homes around it, it is better to focus on just the street itself where cars are driving by.

In the photo below, the left image shows a wider angle of the gate entrance. For best practices ANPR, it is important to zoom the camera closer to the gate.  Again, if the camera can see the vehicle plate well, then our ANPR engine ought to do a very good job of reading the plate.

If you are in an area using CCTV cameras, Plate Recognizer’s software may still work. While CCTV cameras are typically on the lower end of the quality spectrum, they may still be suitable to capture vehicles moving at low speeds.

ANPR Camera Setup: Ideal Camera Distance 

The maximum advisable distance between the camera and the vehicle is 35 meters.  Actually, whenever possible, it is preferred to minimize that distance.  Why? Minimizing the distance between the camera and the vehicle helps ensure that the camera can easily focus without the need to zoom in on the target vehicle.  This helps reduce image blurriness.

When you place the camera far away from the vehicles it needs to read, you will need a camera with very strong zoom capabilities. The more the camera uses the zoom, the harder it is for the images to come out clear and crisp. 

Another cause for blurry images can be if the camera is mounted improperly, or becomes loose. Typically, ANPR cameras are outdoors and exposed to the elements so this is going to happen at some point if the cameras aren’t installed securely. This can cause the camera to move, shake or vibrate.  These small vibrations can result in image blurriness when the zoom level is high.  For example, you can test this yourself by using your smartphone camera and zooming in all the way to view a car in the distance.  Apply a small amount of movement to the camera and you can easily observe how the camera view totally changes!

We have actually tuned our algorithms and even added a new parameter called Merge Buffer to help accommodate camera vibrations.

PRO TIP: Use Your Mobile Phone to Do a Test

Before you set up the camera, use a mobile phone as a test subject. Place the phone in the position where you intend to install your ANPR camera. Set the smartphone to the number of pixels and settings of the camera you plan to purchase.  Then, just record 10 minutes of footage and use Stream to analyze the recorded video for license plate recognition.

Camera Angle To Improve ANPR

While Plate Recognizer ANPR has been tuned to support a wide variety of license plate angles, it’s always ideal to have the camera set up appropriately. In terms of angle, the setup of the ANPR camera can be positioned in two ways: slope, vertically, and horizontally.  For both cases, it is advisable to have a maximum of 45 degrees for a proper read of the license plate. 

Remember, just because you set up your camera for 45 degrees, your customers/drivers don’t always drive in a straight line!  

ALPR vendors can make outrageous claims that their software can do anything, but at Plate Recognizer, we’re not going to lie to you. There are things our software can do, and things it can’t!  Not every angle is going to be possible, and no camera is going to be a super machine that can see a license plate while bending over backward in the middle of a blizzard. 

So for example, Plate Recognizer’s ALPR engine can support up to a 53-degree tilt, and a 70-degree side angle. What it can’t do is catch a plate number at 75 degrees.

In fact, we’ve compiled real-world ALPR results.  Take a look.

Minimum Resolution For Best ANPR

We see a lot of unsuccessful LPR due to very fuzzy images of the license plate.  This is by and large due to the fact that the camera does not have the resolution required to capture a good plate image.

While Plate Recognizer works with any IP camera, we recommend that the license plate itself must have roughly 100 pixels in width.  Otherwise, our ANPR engine may not be able to effectively read the license plate.

Since every LPR camera setup will be different, you’ll need to figure out the correct amount of megapixels (MPs) needed.  Basically, the number of megapixels required will ultimately depend on the distance of the camera to the license plate.

The width of the license plate will depend on the country you’re in.  Here are some examples:

Once you have an idea of the width of plates for your ANPR camera setup, you’ll need to figure out the MPs needed. There’s a bit of math here to calculate, so we’ll save you the headache and go straight to the answer.  

The table below summarizes the maximum distance in feet from the camera to the vehicle plate for each of the 3 major regions/countries.  You’ll note that we used 80 pixels of width for the plate, even though our ALPR benchmarking indicates that our engine can read a plate even at 30 pixels width.  We chose 80 pixels width to add some cushion–just to be on the safe side.

So net net, if you have to set the camera up at over 30 feet from the vehicle plate in the USA, then you’ll need to get a 4 MP camera or better.

PRO TIP: If the above topic on camera resolution is confusing, no worries.  Just use your eyes!  Basically, if you can see the license plate number in the camera footage with your own eyes, then Plate Recognizer’s engine should be able to read the plates, too. But if you’re having a really hard time seeing the plate–even after squinting and zooming in–then please don’t expert Plate Recognizer to do magic.

ANPR Camera Setup for Night-Time: Sufficient Infrared

If you have a great ANPR system, but no infrared (IR) light capabilities, you will have a tough time capturing plate numbers at night. This is because when it’s dark, there’ll be glare on the plate from the headlights.  If you’re using ANPR to detect crime, which often happens at night, you’d need to make sure you have good IR.

Infrared cameras utilize LED lights to illuminate the plate area with infrared light, which is invisible to humans.  Cameras with an IR cut filter automatically adjust IR light levels so that you can get consistent colored images in the daytime and black/white images at night.

Depending on the exterior lighting, you may be able to get a license plate read at night without IR, but it won’t have the same accuracy. Using IR may also help you pick up images in different weather conditions. For example, if you are in a location that gets a lot of rain, an ANPR system that relies on white and natural light will have a hard time getting accurate images. 

For optimal IR use, you’ll want to place the camera on an angle so it isn’t pointing directly at headlights. This will avoid unnecessary glare risks and ensure you’re getting a good shot of the license plate. 

If your current LPR camera doesn’t have IR, you can always buy an inexpensive external IR unit instead of upgrading your entire system. It costs around $20-25 on Amazon.  The IR technology built into a camera may also not be enough, so adding another external device can increase accuracy.

Lighting Tips for ANPR Camera Setup

Adjusting the lighting for your ANPR camera setup is essential to ensure optimal performance and accurate license plate recognition. Proper lighting helps to minimize shadows, glare, and overexposure, which can obscure or distort license plate images, leading to recognition errors. 

By providing even lighting and strategically positioning lighting sources, you can enhance visibility and clarity, particularly in challenging environments such as parking lots, highways, or private properties.

Here are a few lighting tips based on how you’re going to utilize your ANPR setup:

ANPR Camera Lighting for Parking Lots

For parked cars going in and out of a parking lot, the ideal lighting setup would typically involve evenly distributed and consistent lighting throughout the parking area. This helps ensure that license plates are clearly visible to ANPR cameras regardless of the vehicle’s position.

Other tips for optimal lighting in parking lots:

How does IR Lighting help with illumination?

IR lighting emits infrared light, which is invisible to the human eye but can be detected by camera sensors. By supplementing existing lighting sources with IR illumination, ANPR cameras can capture clear and accurate images of license plates even in challenging lighting environments where visible light may be insufficient. This enhances the overall visibility and image quality, allowing the ANPR system to reliably read and process license plate information regardless of lighting conditions.

Additionally, IR lighting helps minimize disturbances to nearby residents or drivers, as it is invisible and does not produce glare or excessive brightness. Overall, IR lighting plays a crucial role in enhancing the performance and effectiveness of ANPR camera setups, particularly in low-light or nighttime scenarios.

Many cameras come equipped with built-in IR capabilities. It’s important to ensure that the camera’s IR distance parameter is well-suited to the distance between the camera and the vehicle being monitored. This ensures that the IR illumination adequately covers the area where license plates are captured, enabling clear image capture for ANPR systems. 

However, in some cases, the built-in IR may not be sufficient to provide optimal illumination, particularly in larger or more challenging environments. In such situations, you may opt to purchase external IR units to supplement the camera’s built-in IR capabilities.

These external IR units can provide additional illumination, extending the effective range of the ANPR system and ensuring clear and accurate image capture, especially in low-light or nighttime conditions where visibility may be limited.

ANPR Camera Lighting for Highways

Highways, on the other hand, need different light requirements since cars are moving at high speeds. The lighting needs to provide sufficient illumination to capture clear and accurate images of license plates despite the fast-paced movement of vehicles. You can try doing the following:

The lighting setup for highways prioritizes high-intensity, uniform illumination to facilitate clear image capture of license plates, enabling ANPR systems to operate effectively in fast-moving traffic environments.

<p>The post Best ANPR Camera System Setup first appeared on NVR IPCAMERA SECURITY.</p>

Once you have the NAS setup you can come back to this post and follow the steps below:
.

Step 1: Login to your Synology NAS via a browser​

Step 2: Click the Package Center icon​

Step 3: Search for and install the Surveillance Station software (it should be on the home page of the package center, if not you can use the search bar to find it)​

Step 4: Click the Synology main menu at the top left of your screen and open the newly installed Surveillance Station software​

Step 5: Click the IP Camera icon​

Step 6: Click the add button when the new window open and then click add camera from the drop-down​

Step 7: Select Quick Setup and then click the next button​

Step 8: Enter the camera details manually or click the Search icon next the IP Address box​

Step 9: Check both the Synology Supported Cameras and ONVIF lists (some camera models are not directly supported by Synology, but as long as the camera is ONVIF compliant you should be able to add it to the Surveillance Station software)​

Step 10: Select the camera you want to add from one of the lists and click OK​

Step 11: Check that all the camera details are filled in, including the cameras username & password (also give the camera a unique name to help you identify it from other cameras)​

Step 12: Click the Test Connection button and if the test is successful you’ll get a green tick and a live shot from the camera, you can then click Finish and the camera will be added to your Synology NAS​

If the test is not successful you will have to go back and check the camera’s settings are correct, the most common problem is that the camera has an IP address that is not on your network, after you have followed our instructions from a previous video on how to change the IP address you should get a successful connection and be able to add the camera.

How To Install Synology Surveillance Station

Read Also : Dahua NVR Troubleshoot All Series

.

If you need more help with installing Surveillance Station and adding an IP Camera to your Synology NAS you can watch this video:

.

Synology NVRs and VisualStation​

NVR1218, DVA1622, DVA3221, VS360HD

NVR’s (Network Video Recorders) are a neccessary part of any security setup.
They work to store, playback and support the live feed of security footage from connected IP Cameras, and with Synology, can offer even more.

.

Offering a range of Network Video Recording solutions, from their energy efficient NVR1218, and compact VS360HD, to their deep learning, AI powered DVA series, Synology’s selection of NVRs were designed to appeal to a range of different users and applications.
At Use-IP you can now choose from these four Synology NVRs and decide which is best suited for your needs.
​

.

.

​

NVR1218​

The Synology NVR1218 is a 2-Bay (Reaching a max. of 7 bays, with an Expansion unit) Network Video Recorder, able to support a max. of 12 IP camera channels.
Its design is also fit for a PC-less experiance (only needing to be connected to a monitor) and can be accessed remotely, via Synology’s Surveillance Station, or, DS cam mobile application (allowing for Live view, playback, adjustments, and notifications, on a mobile device).

Key Features:
.

.

.

​

​

Deep Learning NVR (DVA) Series​

The Deep Learning NVR Series combines the Management features of Synology’s Surveillnace Station, with Advanced Analytics, designed to fit deployments of all sizes.
Intelligent Analytics – Included in DVA NVRs to strengthen on-premises security, offering deep learning algorithms and detection profiles
.

Users can choose between the more compact design of the DVA1622, or the larger storage of the DVA3221, the key features of which are both listed below.
​

DVA1622

DVA3221​

.

The DVA Series NVRs also come equipped with the use of Dynamic Maps, allowing for improved situational awareness, and to help users to determine camera/event locations, and provide instant access to video feeds for more efficient site monitoring. This also includes the features listed below:​

.

.

VisualStation

VS360HD
​

Synology’s VisualStation offers a PC-less, live view and playback solution, for your surveillance footage, with the ability to work in mobile environments.
Designed to work as a companion system, the VisualStation also offers an ultra-compact design, and features Synology SurveillanceStation live view and management tools. It is a perfect alternative for a Video recording solution, for users facing budget or space constraints.

Key Features:
.