Troubleshoot Offline Camera

Troubleshoot Offline Camera

Learn how to troubleshoot when a new Verkada camera is offline

Updated over a week ago

Use this article to read through some common scenarios and try the suggested troubleshooting tips to help. If you still need help, please contact Verkada Support.

What is the LED status of the camera?

Camera has been solid orange for over 10 minutes

Camera is blinking blue for over 5 minutes

Camera is solid blue for over 5 minutes, says “waiting to be connected on Verkada Command”

Roles and Permissions for Cameras

Roles and Permissions for Cameras

Learn about the roles and permissions available for Verkada Cameras

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Cameras.

Org-level roles

Organization-level roles are configured on a per-user basis. Groups cannot be used to set organization-level roles.

Below, click the down arrow to the left of the role to learn more about the role and access.

Org Member

Org Admin

Verkada Cameras Troubleshooting 2024

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

CP52-E PTZ permissions

The CP52-E PTZ camera permissions determine who can manage the Sentry Mode feature.

Permissions model (example)

Here’s a simple example of a permissions model that a typical organization with several sites and users may employ:

Users and their required level of access

Permissions each user should be assigned

.

Set Org Admin permissions

Revoke Org Admin permissions

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Customize roles and permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

Roles and Permissions for Command

Roles and Permissions for Command

Learn about the roles and permissions available to Command users and groups

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Command. It also explains how to customize roles and permissions.

Permission levels

Permissions are set at the following levels:

Daha fazla göster

Permissions considerations

Common user permission configurations

Daha fazla göster

Roles and permissions by Verkada product

.

Org-level roles

Org-level roles are configured on a per-user basis. Groups cannot be used to set org-level roles.

Org member

Org Admin

Access Control Role

.

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

Access Site Admin

.

Customize Roles and Permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

FAQ

Why has my organization disappeared?

Why are cameras missing from my organization?

Why can’t I access certain features or settings, such as other users?

Resolve Issues with Missing Cameras

Resolve Issues with Missing Cameras

Learn how to resolve issues when cameras are missing from your Verkada account

Updated over a week ago

When you log in to Verkada Command, you can only access cameras and video in organizations or sites where your user account has permissions.

Note: Even if you are an Org Admin, you still need to grant yourself permission to view all sites. Learn more about roles and permissions for cameras and Command.

If you log in to Command and cameras are missing or have disappeared, always check user permissions. The most common reason cameras are not visible is that your user account needs permissions to the site(s) where the cameras are configured.

Common reasons that can cause cameras to disappear

Check permissions

If you are an Org Admin, you can check and correct your own permissions:

Resolve Issues with Night Mode

Resolve Issues with Night Mode

Common issues with IR and Night Mode with steps to resolve them

Updated over a week ago

Each Verkada camera has night vision capabilities, using a sensor to detect low-light situations. When external lighting is low, the camera switches to night mode and records in black and white, using infrared (IR) LEDs to illuminate the environment. If the IR is emitted improperly through the dome or reflected into the lens, it negatively impacts image quality.

Common night mode issues

It is imperative that the dome remain free of debris and the camera is installed properly to achieve the best image quality. When viewing footage in night mode if the footage appears obscured it is most likely the result of one of the following scenarios:

Camera always in night mode

If your camera is always in night mode even where there is sufficient light in the environment the lux (light) value may need to be adjusted. If this is the case, reach out to Verkada Support for further assistance.

Environmental obstruction

If the camera is mounted too close to a wall, ledge, or light source, the image quality may be degraded due to IR reflection.

Recommendation. Ensure that cameras are mounted sufficiently far away from surfaces that may cause the IRs to reflect, such as light sources.

IR obstruction

If a first-generation Dome camera (D30 or D50) is operating in night mode when there is plenty of light, the IR sensor is likely obstructed by the camera housing.

To fix the obstructed light sensor, physically rotate the lens barrel assembly 180° so the sensor and IRs are visible through the camera case.

Example: Proper and improper orientation

Note: After rotating the lens barrel, the camera orientation may need to be changed in Command.

<p>The post Verkada Cameras Troubleshooting 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Lorex Fusion: Download the Lorex App

The following article provides instructions for downloading the Lorex App and connecting your Lorex Fusion Collection recorder to the app.

Prerequisite

Before you start, your Fusion recorder must be powered on and connected to your router using the included Ethernet cable. For Basic System Setup instructions, refer to your Fusion recorder’s Quick Start Guide or Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

Download the Lorex App

Once your Fusion recorder has connected to the Lorex App, complete the final Fusion steps by connecting your Fusion Wi-Fi cameras and accessories.

For setup instructions using the new local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (New Local UI).

For setup instructions using the previous local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories.

Lorex Fusion: Frequently Asked Questions

The following frequently asked questions (FAQs) provide more information about your Lorex Fusion Collection. Where applicable, the FAQ includes links to articles where you may find more information.

Lorex Fusion Troubleshooting FAQ.

What is Lorex Fusion?

Our Lorex Fusion recorders incorporate the newest (fusion) technology to connect both Lorex Wired and Fusion Wi-Fi Cameras, Doorbells, Floodlights, and Sensors to one system. Lorex Fusion Wi-Fi Cameras and Accessories can connect to one recorder for continuous 24/7 recording and local, secure storage (up to 10TB). Everything can be accessed from your Lorex App for easy control of all devices.

.

Why do I get an offline message and a blank screen for the (B463AJ) 2K battery doorbell’s channel on the Fusion recorder?

Being a battery-operated doorbell, it will always go to sleep after a period of inactivity to conserve battery life. Once the doorbell is correctly paired to your Fusion recorder, the offline message means the doorbell has gone to sleep but is still connected and can be awakened. When motion is detected, or when the call button is pressed, there will be live video from that channel. You can also manually wake up the doorbell through the Lorex app, by activating the liveview.

.

Can my Battery Video Doorbell record continuously?

To conserve battery life, Wi-Fi Battery Video Doorbells only record when motion is detected. They do not record continuously.

.

Which recorders are part of Fusion?

For a list of Lorex Fusion Recorders, please refer to the Product Compatibility Chart.

.

Can I connect all Lorex Wi-Fi Cameras and Accessories to my Fusion recorder?

Only Lorex Fusion Compatible Wi-Fi Cameras and Accessories can connect to Lorex Fusion Recorders.

.

Which Lorex Wi-Fi Cameras and Accessories are part of Fusion?

See the following list of Lorex Fusion Wi-Fi devices:

.

Should I update my Lorex Fusion recorder’s firmware?

It is recommended to update your system firmware to the latest version to ensure remote connectivity and to support newly added Fusion Wi-Fi devices.

.

Does my Lorex Fusion recorder require a network setup?

Yes, a network setup is required to connect Fusion Wi-Fi cameras and accessories to your Fusion recorder. Ensure you connect the included Ethernet cable to your recorder’s LAN port and your router.

.

Does it matter which router I use?

Yes, due to its strong signal, the dual-band router is suitable for high resolution video recording and for connectivity between devices. Ensure that your Fusion Wi-Fi cameras and accessories and your Fusion recorder are all connected to a dual-band router (2.4 GHz/5 GHz bands).

.

How many Lorex Fusion Wi-Fi Cameras and Accessories can I connect to my Fusion recorder?

This depends on your Fusion recorder and the number of Fusion Wi-Fi channels it comes with. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

What is a Fusion Wi-Fi channel?

A Fusion Wi-Fi channel is the channel you use to add a single Fusion Wi-Fi camera to your system. A 16-channel security system with 8 PoE ports/channels (for wired camera connection) and 8 Fusion Wi-Fi channels means that 8 Fusion Wi-Fi cameras and accessories can connect to the entire system.

Note: Fusion Wi-Fi channel’s are only available on certain Lorex Fusion recorders. For a list of Fusion recorders, see the Product Compatibility Chart.

.

How many Fusion Wi-Fi channels are on my Lorex Fusion Recorder?

The number of Fusion Wi-Fi channels varies per Fusion recorder. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

How do I setup my Lorex Fusion system?

Complete your Fusion setup in the following order:

After connecting your Fusion system, ensure you adjust your Fusion settings.

.

Are there Fusion setup tutorial videos?

For a video walk-through of the Fusion setup with the new local UI (N845, N846, N847, N864, D863, D881 Series), please watch here.

For a video walk-through of the Fusion setup with the previous local UI (N841, N842, N843, N844, N861, D862, D871 Series), please watch here.

.

How do I setup my Lorex Fusion recorder and wired cameras?

For Basic System Setup instructions, refer to your recorder’s Quick Start Guide or Series Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

How do I connect my Lorex Fusion Wi-Fi camera or accessory to my Fusion recorder?

For full setup instructions, please click on the article corresponding with your model number.

.

Which password should I enter to connect my Lorex Fusion Wi-Fi camera or accessory to my Fusion recorder?

Enter the same password that you created in the Lorex App when setting up your Fusion Wi-Fi device.

.

What is continuous recording?

Once your Lorex Fusion Wi-Fi camera connects to your Fusion recorder, your camera’s recording settings are automatically set to continuous. This means that your Fusion Wi-Fi camera will record 24/7 or for the entire duration of the recording schedule onto your Fusion recorder’s hard drive. It is worth noting that recordings on the camera are limited due to the size of its onboard storage, while recordings on the recorder are extensive (3TB to 10TB). Continuous recording captures everything in the background, and you can playback to catch anything you missed.

.

Do all Lorex Fusion Wi-Fi cameras record continuously?

No, to conserve battery life, battery-operated video doorbells do not record continuously (24/7).

.

How do I set my Lorex Fusion Wi-Fi camera to continuous recording?

After Fusion setup, your Wi-Fi camera is automatically set to Continuous recording. To adjust your camera’s recording settings, login to your recorder and navigate to the devices menu. For instructions, please see the article Lorex Fusion: Adjust Settings.

Note: Battery-operated video doorbells do not record continuously (24/7). Being a battery-operated doorbell, it will always go to sleep after a period of inactivity to conserve battery life. Once the doorbell is correctly paired to your Fusion recorder, the offline message means the doorbell has gone to sleep but is still connected and can be awakened. When motion is detected, or when the call button is pressed, there will be live video from that channel. You can also manually wake up the doorbell through the Lorex app, by activating the liveview.

.

How come I’m receiving duplicate notifications in the Lorex App?

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder. For instructions, please see the article Lorex Fusion: Adjust Settings.

.

After Fusion setup, where is my Lorex Fusion Wi-Fi camera’s video footage being stored?

Your Lorex Fusion Wi-Fi camera saves recorded motion detection videos onto the local microSD card (not always included). Once you’ve connected your Fusion Wi-Fi camera to your Fusion recorder, your camera’s recording settings is automatically set to 24/7 Continuous recording, and all recorded video is stored on your recorder’s extensive hard drive (up to 10TB).

.

What features are supported in my Fusion recorder vs. the Lorex App?

Please see the following list of features supported in either your Fusion recorder and/or the Lorex App:

.

Can I use my web browser to access my Lorex Fusion Wi-Fi camera?

You can only access your camera on the Lorex App, recorder, or on the Lorex Cloud Client.

.

When modifying the password in the Lorex Cloud Client, which password should I enter?

Enter the password for your Wi-Fi camera or accessory created in the Lorex App during setup.

.

Where can I order the Lorex Fusion Collection?

To order, go to lorex.com.

Lorex Fusion: Troubleshooting

The following article provides some troubleshooting tips for setting up your Lorex Fusion Collection.

.

My Fusion Wi-Fi camera or accessory is not appearing in the device list.

.

My Fusion Wi-Fi camera or accessory is not connecting to my Fusion recorder.

• Give your Fusion Wi-Fi camera or accessory a few minutes to establish a connection.

• Check to see if your Fusion recorder has the most up-to-date firmware. New Local UI: Login to your recorder and navigate to System > Update & Reset > Upgrade, then click Check for Updates.  Previous Local UI: Login to your recorder and navigate to Main Menu > Information > Update/Reset > Update, then click Check for Updates. For instructions on updating your recorder’s firmware through USB, see the article How to manually upgrade the firmware of your recorder.

• Ensure that your Fusion Wi-Fi cameras and accessories and your Fusion recorder are powered on.

• The same password created for your Fusion Wi-Fi camera or accessory in the Lorex App must be entered in your Fusion recorder. If you have forgotten the password, then reset your Fusion Wi-Fi camera or accessory and connect it to the app again.

• (Applies to the previous local UI only) If your password for your Fusion Wi-Fi camera or accessory is entered incorrectly in your Fusion recorder, then your Wi-Fi device will lock itself. Reset your Fusion Wi-Fi camera or accessory and connect it to the app again.

• Ensure that you are entering the password for your Fusion Wi-Fi camera or accessory created in the Lorex App, and not the Lorex App account password. Those are two separate passwords.

• Ensure that your Fusion Wi-Fi camera or accessory is connected to a dual-band router (2.4 GHz/5 GHz bands).

• Ensure that you are connecting the Fusion Wi-Fi camera or accessory to an available Fusion Wi-Fi channel, and not a Wi-Fi channel that already has a Wi-Fi device connected to it.

.

I don’t know the password for my Fusion Wi-Fi camera or accessory.

If you don’t know the password for your Fusion Wi-Fi camera or accessory, then you will need to reset the device and connect it to the Lorex App again.

To reset your Fusion Wi-Fi camera or accessory:

.

I’m receiving duplicate notifications in the Lorex App.

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder. For instructions, please see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N910 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi Cameras and Accessories to your N910 Fusion recorder.

.

Our Lorex Fusion recorders incorporate the newest (fusion) technology to connect both wired and Wi-Fi cameras, doorbells, floodlights, and motion sensors to one system. All Fusion compatible Wi-Fi cameras and devices connect to one recorder for continuous 24/7 recording and private local storage. Access everything from the Lorex App for easy control of all devices.

Note: To conserve battery life, Wi-Fi Battery Video Doorbells only record when motion is detected. They do not record continuously.

For any connection issues, see the article Lorex Fusion: Troubleshooting.

.

Part One — Wired Setup

Setup your Fusion recorder and wired cameras. For Basic System Setup instructions, refer to your recorder’s Quick Start Guide or Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

Important: Network setup is required for your system — use the included Ethernet cable to connect your recorder to your router.

.

Part Two — Connecting your Lorex Fusion Wi-Fi Camera

Connect your Lorex Fusion Wi-Fi Camera to the app and then from your recorder scan your network to add it.

.

Option A — Connecting Your New Lorex Fusion Wi-Fi Camera to Your Recorder

Add compatible Lorex Fusion Wi-Fi Cameras and Accessories onto Fusion Wi-Fi channels on the recorder.

To connect your New Lorex Fusion Wi-Fi Camera to the recorder:

Note:

.

Option B — Connecting Your Existing Lorex Fusion Wi-Fi Camera to Your Recorder

Add compatible Lorex Fusion Wi-Fi cameras and accessories onto Fusion Wi-Fi channels on the recorder.

Note:

To enable remote viewing for the mobile app, you will need to:

To connect your Existing Fusion Wi-Fi camera to the recorder:

1.From the Live View display, click the pair icon  in the center of the Fusion Wi-Fi channel’s screen.

Note: It may take a few minutes for your Lorex Fusion Wi-Fi Camera’s video feed to appear.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N845, N846, N847, N864, D863, D881 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi cameras and accessories to the Lorex App and to your Fusion recorder.

Note: These Fusion instructions apply to the new local UI only. For Fusion instructions that apply to the previous local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories.

.

Before you start

.

Watch the Lorex Fusion setup tutorial video

For a video walk-through of the fusion setup, please watch here.

.

Connect your Fusion Wi-Fi cameras and accessories to the Lorex App

Follow the Lorex App steps to add your Lorex Fusion Wi-Fi cameras and accessories. Refer to your camera’s documentation at help.lorextechnology.com for detailed setup instructions. Search your camera’s model number to access the product support page.

Note:

2.In-app, tap the  icon to add your Wi-Fi camera.

.

Connect your Fusion Wi-Fi cameras and accessories to your Fusion recorder

Note: You can add one Wi-Fi camera or accessory to one Fusion Wi-Fi channel. The number of Fusion Wi-Fi channels varies per Fusion recorder. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

2.From the Live View display, click the pair icon  from the center of the Fusion Wi-Fi channel.

Note: If your Lorex Fusion recorder and Fusion Wi-Fi camera share the same password, then the devices will automatically connect without entering the password.

.

After successfully connecting to your Fusion recorder, your Fusion Wi-Fi camera or accessory connection status turns green. For any connection issues, see the article Lorex Fusion: Troubleshooting.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N841, N842, N843, N844, N861, D862, D871 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi cameras and accessories to the Lorex App and to your Fusion recorder.

Note: These Fusion instructions apply to the previous local UI only. For Fusion instructions that apply to the new local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (New Local UI).

.

Before you start

.

Watch the Lorex Fusion setup tutorial video

For a video walk-through of the Fusion setup, please watch here.

.

Connect your Fusion Wi-Fi cameras and accessories to the Lorex App

Follow the Lorex App steps to add your Lorex Fusion Wi-Fi cameras and accessories. Refer to your camera’s documentation at help.lorextechnology.com for detailed setup instructions. Search your camera’s model number to access the product support page.

Note:

2.In-app, tap the  icon to add your Wi-Fi camera.

.

Connect your Fusion Wi-Fi cameras and accessories to your Fusion recorder

Note:

After successfully connecting to your Fusion recorder, your Fusion Wi-Fi camera or accessory connection status turns green. For any connection issues, see the article Lorex Fusion: Troubleshooting.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Adjust Settings

The following article provides instructions for adjusting your Lorex Fusion Collection settings.

.

Turn off duplicate notifications

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder.

To turn off duplicate notifications:

2.Under your Fusion recorder, swipe left to find your Fusion Wi-Fi camera or accessory.

3.Tap on your Fusion Wi-Fi device’s notification icon .

.

.

Adjust the recording settings for your Fusion Wi-Fi camera or accessory

After Fusion setup, your Lorex Fusion Wi-Fi camera’s recording settings will automatically adjust to Continuous, recording 24/7 directly to your recorder’s hard disk drive.

To adjust the recording settings (new local UI):

To adjust the recording settings using the previous local UI, navigate to Main Menu > CAMERA > Recording > Recording and follow the same steps as above.

.

Set the recording schedule for your Fusion Wi-Fi camera or accessory

You can set a custom recording schedule according to your needs. For example, you can set the system to record continuously during business hours and record on motion detection only outside of business hours.

• Click-and-drag on each day to customize the recording schedule. The schedule is set up as a grid, with each block representing two hours.

• Click  beside 2 or more days to link schedules (). This allows you to quickly change multiple schedules at once.

• To make fine adjustments to a schedule, click . This will allow you to set exact start and end times for a schedule.

• To disable all recording of the selected type on the selected day, click .

To set the recording schedule using the previous local UI, navigate to Main Menu > STORAGE > Schedule and follow the same steps as above.

.

Link sensors to cameras

Once you’ve completed the Fusion setup, you can link motion and door/window sensors to any compatible camera, so that when the sensors are triggered the linked automatically cameras record.

.

To learn more about using your Lorex Fusion system, visit the Fusion page or refer to the Lorex Fusion: Frequently Asked Questions article.

.

<p>The post Lorex Fusion Troubleshooting FAQ first appeared on NVR IPCAMERA SECURITY.</p>

.

This tutorial applies to NVR Face Recognition ai systems

How to Install xmeye poe nvr systems

1.Power on the NVR with the 48Vor 52V power adapter.

2.Connect your NVR to the router.

3.Connect the NVR to a monitor via VGA or HDMI cables.

4. Connect the PoE Cameras to the NVR with the PoE Ethernet cables.

5.Switch on the NVR and turn on the monitor.

6.lf your monitor doesn’t have a speaker, you can connect a speaker to the 3.5mm “AUDIO OUT” port to get sound from the recorded video.

XMEYE NVR Face Recognition guide

Read Also : Camius Devices FAQs and How-Tos

Getting Started Settings

At your first login to the system, there will be a quick guide to help you set up the basic information of your NVR.

Time Setup

Please adjust the time and date to be the same as your local.

Network

On this page you could see the network information about your system. Click “Next” to continue.

Install XMeye App

Scan QR code of the App to download the app.After the app downloaded, please create your own profile account on the app. And then scan the QR code of the serial number of the NVR to add it into the app. Please ensure the NVR is online before you watch videos of it on the App.

CameralChannel Setting

Before installing your cameras to the final position, please check and adjust the position and the angle of the cameras.

Display

Adjust the display settings of the monitor images

General Setting

In the General Settings, you can change the language, the action when the storage is full and the auto logout intervals if you want to get a better protection of your NVR.

Record Configuration

In the Record Configuration, you can set up the record mode for each channel to save space of the HDD and only record the important videos. 

Channel: The channel which you want to do settings of record configuration.

Length: The standard length of each video segment.

Mode:The way you want to record videos. 

1.Schedule:The selected channel will only record during the chosen time period.

2.Manual: The selected channel will record 24/7.

3.Stop:The selected channel will not record any video.

*Notice: If you would like to set the recording mode to “Alarm”, please make sure that you have enabled the alarm function of the corresponding channel.

Alarm settings

lntelligentAlert

The Al smart security camera system supports intelligent alerts.such as human detection and face detection. In order to adjust the related settings, please enter “Intelligent Alert “in “Alarm” menu.

Channel:Choose the camera which you want to do alert settings. 

Enable:When you tick off it , the camera will not detect any movements. 

Human Detect:The camera will detect human activities by recognizing humanoid body shape.

Face Detection:The camera will detect human face when this is ticked. 

Record: When this option is ticked on, the camera will record a video segment when human detected. 

Mobile Reported: When it is ticked on, the camera will send alert notifications to your mobile app when it detects movements or human activities.

Alarm Sound: When it is ticked on, the camera will sound a voice alarm when it detects movements or human activities.

Sensitivity:Adjust the detection sensitivity of the camera. 

Rule:Set advanced detection rules like safe zone or line cross alarm. 

*Notice: If the “Enable” option is on and the “Human Detect” is off, the camera will detect all movements, including pets, vehicles, plants, trees, etc. Therefore, we recommend you to active “Human Detect” to reduce false alerts. It shows that “Human Detect” function can reduce 98%-99% of the false alerts.

Advanced Settings of Human Detection

Period: The time period of the detection. 

MD Interval: The interval between 2 human motion movements alerts. 

PostRec: To adjust the length of the video after the camera detects abnormal movements.

Tour: Not applicable. 

Snapshot: When it is ticked on, the camera will take snapshots when it detects abnormal movements. 

Send Email: When it is ticked on, the camera will send alerts to your e-mail address. 

Buzzer: When it is ticked on, the NVR will make beeps alarm after the camera detects abnormal movements. 

Write Log: When it is ticked on, the NVR will note down the alarm record. You can
review the records by following this path: Right-Click Menu > Main Menu > Advanced > LOG. 

FTP Upload:Not Applicable. 

Voice Prompts:To choose the different alarm sounds for the voice prompts. 

Advanced Settings of Face Detection

Period: To Set the time period of detection. 

MD Interval: The interval between 2 alerts.

PostRec: To adjust the length of the video after the camera detects abnormal movements.

Tour: Not applicable.

Snapshot: When this option is on, the camera will take snapshots when it detects abnormal movements.

Send Email: When this option is on, the camera will send alerts to your e-mail address.

Buzzer: When this option is on, the NVR to sound alarm when the camera detects abnormal movements. 

Write Log: When this option is on, the NVR will note down the alarm record. You can review the records by following this path: Right-Click Menu > Main Menu > Advanced> LOG. 

FTP Upload: Not Applicable. 

On screen of the monitor with live video , you can view the human faces detected by the cameras. You can easily and quickly get whether the persons detected by the camera are your friends or an intruder. If it is an intruder, the face detection function can help take some actions as soon as possible to protect your safety and property. Please follow the path below to enable the “Face Detection”.

Right-Click Menu > Face Detection

When the cameras detect human faces, the NVR will show you these faces on the right side of the screen like the image above.

How to Set Up Your Email to Receive Alert Notifications

Please follow the paths below to set up the email which you want to get alerts from the security camera system.

Right-Click Menu > Main Menu > Network > Net Service > EMAIL (Please OUBLE CLICK on “EMAIL” to enter the setting interface)

Please enter the required information of your emails in the “User Name” “Sender” and “Receiver”.
If you want to receive the alert notifications with an email different from sender email address, you can input a different email in the “Receiver”.
In the “Password”, you need a 16 digits App password. Let’s take “Gmail “as an example to show you how to get this password.

*Notice: Each e-mail service provider has its own SMTP server, port and encryption. You can find these information easily on Google. In this manual, we will show you these information of several common used e-mail service. camera is lost connection.

Gmail SMTP: smtp-relay.gmail.com Port: 25, 465 or 587

Encryption: SSL or TLS

Hotmail SMTP: smtp.live.com Port: 25 or 465

Encryption: SSL or TLS

Outlook SMTP: smtp.office365.com Port: 587
Encryption: TLS

Yahoo SMTP: smtp.mail.yahoo.com Port:465
Encryption: SSL or TLS

iCloud SMTP: smtp.mail.me.com Port: 587
Encryption: SSL or TLS

How To Get 16-Digit App Password

Enable IMAP access of your e-mail.

Log into your Google account. In “Security” section, find “Signing in to Google”.

If the “2-Step Verification” is off, please enable it.

Enter ”App passwords”. Select the app and device for which you want to generate the app password, or you can name your own app and device, then click “GENERATE”.

You will get a 16 digits password, this is the password you need to use later to set up your e-mail notice in NVR system.

* Notice: You are not able to review the password after you click “DONE” so please note it down or leave this page open.

Rule – Safe Zone & Line Cross Alarm

We can set up a safe zone for our camera.

The camera will only detect or sound alarm when there’s abnormal activities in the safe zone. Click on the “Set” button next to “Rule”.

Choose the safe zone shape which you would like to use. In this user manual, we use rectangle as example.

Choose the safe zone shape which you would like to use. In this user manual, we use rectangle as example.

We can also choose other size such as circle to protect our valuable objects.

When we choose “Tripwire” in stead of “Intrusion”, there will be a line on the screen and the camera will only detect or sound alarm when people cross this line.

Abnormality

In this part, we can set the alarm for other events.

In the “Event Type”, there are several options:

You can also choose different notification type:

Traditional Alarm

In this part, we can set the alarm for other events.

In this part, we can adjust the settings for other alarm types.

Video Blind: The camera is covered and blinded. 

Video Loss: The camera loses connection with the NVR.

Alarm Input: The alarm input from the cameras.

Intelligent: Not Applicable. 

Video Blind

Channel: Choose the right channel of which you would like to adjust the settings. 

Enable: The master switch of the video blind alarm. 

Sensitivity: Change the sensitivity level of the video blind alarm. 

Period: Set up the time period during which you would like the video blind alarm to function.

Record Channel: Set up the channels which you would like them to record videos after the video blind alarm is triggered.

*e.g. You have set channel 1 and channel 2 to record videos in “video blind” interface. One day, a burglar walks to your front door and your channel 1 camera sounds an alarm. The burglar covers the camera with his jacket and run to your driveway, where your channel 2 camera is installed. When the video blind alarm is triggered by channel 1, because you have set channel 2 to record videos too, so the channel 2 camera will also record videos and you will have videos with multiple angles of this burglar. These evidence will help police officers to catch this criminal.

Tour:Not applicable. 

Snapshot:Set up the channels which you would like them to take snapshots after the video blind alarm is triggered. 

PostRec: The length of the video blind alarm video. 

Send Email: If this option is on, the NVR will send alert notification to your e-mail address when the video blind alarm is triggered. 

Buzzer: If this option is on, the NVR will sound alarm when the video blind alarm is triggered. 

Write Log: If this option is on, the NVR will note down the alarm record. You can review the records by following this path: Right-Click Menu> Main Menu > Advanced > LOG

FTP Upload: If this option is on, the NVR will sound alarm when the video blind alarm is triggered.

Mobile Reported: If this option is on, the NVR will send alert notification to the App when the video blind alarm is triggered. 

Video Loss

Channel:Choose the right channel of which you would like to adjust the settings. 

Enable:The master switch of the video loss alarm. 

Period: Set up the time period during which you would like the video loss alarm to function.

Record Channel: Set up the channels which you would like them to record videos after the video loss alarm is triggered. 

Tour:Not applicable. 

Snapshot: Set up the channels which you would like them to take snapshots after the video loss alarm is triggered. 

PostRec: The length of the video loss alarm video. 

Send Email: If this option is on, the NVR will send alert notification to your e-mail address when the video loss alarm is triggered. 

Buzzer:If this option is on, the NVR will sound alarm when the video loss alarm is triggered. 

Write Log: If this option is on, the NVR will note down the alarm record. You can review the records by following this path: Right-Click Menu> Main Menu > Advanced > LOG

FTP Upload: Not applicable. 

Mobile Reported: If this option is on, the NVR will send alert notification to the App when the video loss alarm is triggered. 

Alarm Input

Type: Not applicable. 

Alarmln: The source of the input alarm. 

Enable: The master switch of the alarm input alert. 

Period: Set up the time period during which you would like the alarm input alert to function.

MD Interval: The interval time of each alarm. 

Record Channel: Set up the channels which you would like them to record videos after the alarm input alert is triggered. 

Tour: Not applicable. 

Snapshot:Set up the channels which you would like them to take snapshots after the alarm input alert is triggered. 

PostRec: The length of the alarm input alert video. 

Send Email: If this option is on, the NVR will send notification to your e-mail address when the alarm input alert is triggered. 

Buzzer: If this option is on, the NVR will sound alarm when the alarm input alert is triggered. 

Write Log: If this option is on, the NVR will note down the alarm record. You can review the records by following this path: Right-Click Menu> Main Menu > Advanced > LOG

FTP Upload: Not applicable.

Mobile Reported: If this option is on, the NVR will send notification to the App when the alarm input alert is triggered. 

Snapshot Configuration

In “Snapshot Configuration”, we can set our cameras to take snapshots.

Cycle Capture

When we choose “Cycle Capture”, the camera will take snapshots periodically. For example, the default snapshot period is 64 seconds, it means the camera will automatically take snapshot every 64 seconds.

EMAIL: When this option is on, the NVR will send the snapshots captured by the cameras to your e-mail address. 

FTP: Not applicable. 

Storage: When this option is on, the NVR will store the snapshots captured by the cameras in the HDD. 

Timing Capture

When we choose”Timing Capture”, the camera will take snapshots at the time that we set.

Playback

In this part, we can review the video records taken by the cameras.

There are 6 different playback modes:

Common Playback: You can review all the video records.

Common Playback: You can review all the video records.

*e.g.:
On May 1st, you only have your channel 1 recording videos;
On May 2nd, You have your channel 1 and your channel 2 recording videos;
In “Common Playback”, you will see that there are records on May 1st and on May 2nd;

Dayparting: You can review the video records of the chosen channels during the selected period.

Smart Express: The selected alarm type videos will play at normal speed. The remaining videos will speed up to save your time. 

Smart Search: You can review the video playback of the selected alarm type within the selected time period. 

Face Search: You can review the video playback of detected human faces in the selected time period. 

<p>The post XMEYE NVR Face Recognition guide first appeared on NVR IPCAMERA SECURITY.</p>

Getting Started: Setting Up User Privileges

The VORTEX Portal provides a structured hierarchy of user roles to ensure smooth management while maintaining high security. This article will guide you through understanding and setting up the four roles: Owner, Admin, Supervisor, and Viewer.

Who Sees What

Below is a table that explains in detail each role and their associated features:

Vivotek Vortex Camera Ultimate Guide

Read More : iViewer installation and user guide

How to set up privileges for a user

Step 1: Go to the Users page.

Step 2: Click on a user’s name or profile to enter their detail page.

Step 3: Locate and click the “Access settings” button on the top-right.

Step 4: Assign the appropriate device groups for permission.

Step 5: Once you’ve made the necessary changes, click “Save” to finalize the settings.

.

Getting Started: Setting up your VORTEX account

To access the VORTEX system, please proceed the following steps to set up your VORTEX account.

Step 1. Scan the QR code below to download the VORTEX app.

Step 2. Open the application in your mobile device and click on the “Create account” button to create a VORTEX account.

Step 3. Type your email to be use to access the system and set a password.

Enter an email address and a password. The password should contain 8 to 64 alphanumeric characters, including at least one uppercase letter, one lowercase letter, and one numeric character. Spaces are not allowed. When finished click on the “Create account” button. 

The application will send an email to the configured address so that you can activate your account. 

Step 4. Access your email and look for a “Welcome to VIVOTEK Vortex” email. If you cannot find it, you can search it by using the mail filter “no-reply@verificationemail.com”. Then, click on the “Verify Email” to activate your account. 

Once the account is activated, you will see the following message in the browser:

Step 5. Go back to the application and login into the system by using your email and password.

Congratulations! You now are able to access the VORTEX service in your phone!

Getting Started: Adding your VORTEX camera to your VORTEX account

VORTEX cameras are very easy to configure. Here is a detailed step-by-step guide that will teach you how to add the device: 

Step 1. In your mobile device, run the VORTEX application. 

Step 2. Access the VORTEX service using your email and password. 

Step 3. Click on your account icon to open the application menu. 

Step 4. Click on “+ Add devices” button to start adding your device.

The application will open the camera feature (be sure to enable the respective permissions). Then, scan the QR code located either on the package box or on the camera itself.

If the scan is successful, you will first see the camera’s general information. Be sure that the information displayed is correct. 

Step 5. Click on the “Add” button to add the device to your account. Once added you will see the following message:

If you want to keep adding devices, click on the “Add another device” button and repeat the same process. 

Step 6. Check that the device is visible in the application. 

You can also go to the VORTEX Portal and check that the camera was added to the system properly. 

<p>The post Vivotek Vortex Camera Ultimate Guide first appeared on NVR IPCAMERA SECURITY.</p>

Access from smartphone

(1)Download APP

Search and download “Eseecloud” app from App store or Google play on your phone.

.

(2) Register

 If you install and open “Eseecloud” app at the first time, an account need to be registered initially.

ce”.

.

(3) Add device

Method 1: Add the device via QR code.

EseeCloud Devices Advanced User Guide

Read Next : EseeCloud Wireless Security Camera System Installation.

.

Method 2: Add by cloud ID.

     Cloud ID: Enter NVR’s System Setup – Network Setup to input Cloud ID or Scan QR Code)

     Device name: Choose a name for your system of your choice.

     User Name: Enter the NVR’s User Name (default: admin)

     Password: Enter the NVR’s Password (default: NO password)

.

.

Method 3: Add by LAN scan.

Please make sure you are connected to the same wifi.

.

Access from remote PC

1. Access from remote PC (Log in with Cloud ID)

Operation Steps: ( We suggest you to use microsoft IE, otherwise some services will be invalid. )

1. Open your browser

2. Enter http://www.e-seenet.com

.

Cloud ID: (Enter NVR’s System Setup-Network Setup to input ID or Scan QR Code)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

3. Enter the correct device ID, user name and password.

4. Click login to enter live view interface.

.

Note: To successfully remote access your system, the device ID should be ONLINE.

.

2. Access from PC Client (CMS)

1. Please download CMS from the below link:

http://www.tontonsecurity.com/download/page_show_67.html

2. Login user: admin, password: (default: NO password, please keep it blank)

3. Please enter “Add” to add device, you can add it “By IP/DDNS” or By Cloud ID”

4. By IP/DDNS:

IP/DDNS: (Enter NVR’s System Setup-Network Setup to find IP)

Port: (default: 80)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

Device name: Choose a name for your system of your choice.

Type: choose “NVR”.

Number of Channels: please input the correct number of the channels.

Click “Finish” and go back to “Preview”, click the device name to view live video.

5. By Cloud ID:

Cloud ID: (Enter NVR’s System Setup-Network Setup to find IP)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

Device name: Choose a name for your system of your choice.

Type: choose “NVR”.

Number of Channels: please input the correct number of the channels.

Click “Finish” and go back to “Preview”, click the device name to view live video.

Add the IP camera to the NVR by matching code

1.  When you use Match Code
1.1 Add new add-on cameras to your system
1.2 Re-pair camera to NVR when they lose connection. You need to delete the
Network Unreachable channel at first, then re-pair the camera to an unoccupied
channel. (unoccupied channel always shows No Video Source under Status.)

Tips: The IP cameras in pre-packed kits have already been paired to the NVR. So the
cameras will automatically connect to the NVR once they are plugged in power.

2.  Add camera by matching code.
2.1  Power on the camera which has no video, and connect this camera to the NVR
via Network cable.

.

2.2  Right click mouse on the main interface, select “Video Manage“

2.3  Click “Refresh“, find the camera’s IP. Click “Match Code“, then click “Yes“, the
NVR will start to match code to the camera.

.

2.4  After matching code successfully, the “status” will show “Connect success“.

Then you will see the camera is added to the NVR and display video on the screen.

.

What is the WiFi distance of the wireless kits?

.

Between each camera to the NVR:

In open space we tested 350m (1150ft) working distance;

With normal obstacles like 1-2 walls, we tested 35m (115ft) working distance.

For distance we only have theoretical values.

No certain distance can be guaranteed due to different environments applied in.

It varies depending on obstacles and signal interference.

on the contrast, if there are many blocks and signal interference between, the distance could be closer. 

.

What if your NVR system keeps beeping?

1. Please right click your NVR mouse, then click System Setup – General Setup – Error setup, make sure that “Enable” and “Buzzer” are unchecked.

2. Please right click your NVR mouse, then click System setup – Channel setup –  Video detection, make sure that “Buzzer” is unchecked for all channels.

3. If you have checked above 2, and none of the buzzer are checked.

    Follow below to stop the beeping:

    a. Right click your NVR mouse, then click System setup – System Admin –  Factory setting, uncheck WiFi Reset, then click Apply to reset NVR settings.

    b. If you cannot view the cameras on the NVR after resetting, please right click your NVR mouse, then click Exit system, choose shutdown. Follow on-screen message to unplug NVR from power and then re-plug it back to NVR. Wait for NVR to initialize.

Then the cameras shall come back.

.

How to upgrade the NVR system

.

.

1. Please download the update file to your computer and unzip it, then plug the USB flash drive,and move the unzipped update file to the root directory of the USB flash drive. 

Note: 

1)Please move the update file to the root directory of the USB flash drive, do not move the subdirectory.

2)Do not change the file name.

.

.

2. Connect USB-disk/mouse and USB hub with NVR shown as flowing.

.

.

3. Enter the NVR’s menu (System setup\System Admin\System upgrade),
Click “Start” to begin upgrading.
.

Note: Please keep power supply well during the upgrade.

.

.

4. Once the upgrade is done, NVR will restart system automatically.

.

.

How to view playback on NVR system

.

1. Right click the mouse , choose video playback

.

2. In the menu bar on the right, choose record type/channel/data to search what
you want to and click playback.

.

3. Click Backup and the video will be saved in USB storage

.

How to Add C8601 Cameras to Tonton NVR System

.

Document

.

or

.

Video

.

How to connect and set up the Wireless Network Camera System?

.

.

1. Connect the DC 12V/2A power adapter to the Power port of the NVR.

When Power indicator light is on, NVR starts to work.

2. Use VGA / HDMI cable to connect your NVR and Monitor / TV, then preview interface can be seen.

3. Plug the network cable and mouse to the ports of NVR rear panel.

4. Connect the DC 12V/1A power adapter to the IP camera (IPC).

Each camera has one 6ft length power adapter.

5. After finish connecting, the NVR will search the IPC automatically and start to initialize the connection.

When completed connection, the images will display.

6. Login this system:

Username :  admin

Password:  (there is no password, please keep it blank)

(Note: if you want to change the password, you can go to NVR’s System Setup – System Admin -User management – Set password to change it.)

7. Then you can follow up the below steps to set up on your phone:

If you want to view the cameras remotely, the NVR should be connected WAN network, Please ensure DHCP in your Router is open.

If you don’t know how to enable the Router’s DHCP, please input the IP Address of your  

Router to IE browser, then you will find the network information, you can enable the “DHCP”.

After that, please go to NVR’s System Setup – Network Setup to enable “DHCP”

Then the system will obtain the IP Address, DNS from your Router automatically.

Or you can go back main menu to select “Fast Network”, Then the system will connect the WAN network automatically.

8.   Access from smartphone

(1). Please download “Eseecloud” app from App store or Google play on your phone.

    (2). If install and open “Eseecloud” app at the first time, an account need to be registered initially.

(3) Add the device.

Method 1: Add the device via QR code.

.

.

Method 2: Add by cloud ID.

Cloud ID: Enter NVR’s System Setup – Network Setup to input Cloud ID or Scan QR Code)

Device name: Choose a name for your system of your choice.

User Name: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

.

.

.

Method 3: Add by LAN scan.

Please make sure you are connected to the same wifi.

.

.

9. Access from remote PC (Log in with Cloud ID)

    PC : our item only support IE browser, please input “www.e-seenet.com” to IE Browser to view your cameras.

       Cloud ID: (Enter NVR’s System Setup – Network Setup to input ID or Scan QR Code)

       Username: Enter the NVR’s User Name (default: admin)

       Password: Enter the NVR’s Password (default: NO password)

(Input the correct Cloud ID, user name and password, click login to enter live view interface.)

.

NVR video backup.

1.Right click mouse > select Video backup.

.

2. Enter into the interface of Video backup.

   Select Channel, Record mode and Search time.

   Click “Search”. After that, the chosen video will display in the list.

3. Select the section which you want to backup.

   Then, click the bottom “Backup”.

4. Next, there will pop up a dialog box asking are you sure to backup this record.

   Click “Yes” if you are sure.

   Before start to backup, system will inform you to insert U disk within one minute. 

   If you want to cancel the operation of backup, you can click “Cancel” to withdraw.

   NOTE: The NVR only one USB port, so you have to unplug the mouse

and plug the U disk within one minute.

5. After you insert U disk, what you should do is just wait a moment.

6. Backup is completed when system inform you “Backup record succeed“.

   And you can unplug your USB disk at that time.

.

How to setup audio function?

1. System connection

(1) The monitor must have HDMI input port.

  (2) Connect the HDMI port on both sides with the included HDMI cable.

2. NVR setup

  (1) Choose the option “Private” on this interface during NVR’s restarting. It allows you select audio or not.

(2) Check whether the encode mode is “AV stream” or not.

(3) On the live window, click mouse to select any channel to pop-up the hidden volume icon like a speaker, click it repeatedly to hear or mute the sound from camera.

.

How to use a new Gmail mailbox account to set NVR mail alarms?

How to use a new Gmail mailbox account to set NVR mail alarms?

1.Register a new Gmail mail account, and log in.

2.Get into your mailbox>click the “” in top right of page>get into “My Account“.

3.     Click “Sign-in&security” and enter the interface,Turn on “Allow less secure APP on“.

4.  After that, you will receive an email from Google, which means “less secure sign in” has been turned on.

5. Get into NVR system. Right click mouse>select System setup>Network setup>Network Status.

   Check if your NVR’s network connected successfully.

   Before operate what mentioned above:

    Make sure Cloud(P2P) display “ONLINE“.

   Make sure the Network Status display “Healthy Network“.

6.Then, click the “E-Mail”. 

Input your Gmail SMTP Server (smtp.gmail.com) in ” SMTP Server” Input your Gmail account in “Username” and “Sender”.

Change the “Encryption Type” to “TLS”.

Input your Gmail password in “Password”

Input your two inbox address in “Sendee 1\2” 

After that, click “Apply”>click “Test”.

7.        When the system remind you “Test successful”, which means NVR’s mail alarm is set successfully.

8. PIR video detection setting as below picture:

    (1). Click “Channel setup” and “Video detection”

    (2). Choose Motion Detection, disable it

(3). Choose PIR Input Armed Detection, Enable E-mail Notice

9. After finished setting, When alarm is triggered, you will receive email from NVR.

PIR alarm setting

Only PIR detection recording setup

1.      Disable motion detection function, click ok to save

2.      Choose Detection Model with PIR Input Armed.

Please noted: If you want to set Buzzer, Email notice or App alarm, you can enable them, in this way, you will get notification on email or App.

3.      Press “Reset” to clear default setting

.

4.      Click the icon “Alarm”

5.      Press and drag the left button of the mouse to select needed schedule.

6.      Click ok to save

7.      Cancel the manual recording mode

.

.

.

8.      Once the PIR detection is trigged, the live window will display an icon like below, it means PIR recording is running

.

How to Reset NVR’s Password

Reset NVR’s Password

1. The interface when you log in. 

 2. Click “OK”. If you input incorrect password,

     monitor will display “Username/Password Is Incorrect!”.

 3. Continuously and successively click left button and right button in blank space of prompt box for six times.After that, monitor will display “Restore default user”.

4. Click “Yes”, and you will access to the interface where you can reset NVR’s password.

Tips:   1. The username must be “admin”, or else the password won’t be retrieved.

           2. If you want to make new password, please leave it blank in column of “Old password”.

           3. Delete the old password after reset the new one.

           4. If you have set a new password for NVR, remember that NVR password cannot exceed 10 characters, or the NVR will not save it correctly.

.

 reset NVR’s password             click to download video

How to install iSmkit PC client 

.

How to install iSmkit PC client                  Click here to download

Gmail Mail Configuration Guide

(DE) Gmail Mail-Konfiguration Anleitung 

click here to download

.

(FR) Guide de configuration de Gmail Mail 

click here to download

.

(CN) Gmail邮件配置指南操作步骤20230922

click here to download

.

(EN) Gmail Mail Configuration Guide 

click here to download

.

Email SMTP and POP3 settings

.

click here to download

.

Solve the problem of the white light always on(Applicable to 3.6.60 and above Version)

Precautions:

1. Please check your IPC version first, only 3.6.60 and above version can be solved the problem through upgrade.

2. The camera must be able to produce the image, if the camera can’t be viewed or resetted, it can’t be upgraded.

.

Check IPC Version:

Go to “System Admin” – “IPC Maintenance” to check the version of the problem camera. Please note: Don’t upggrade the version 3.6.16 and below version with these upgard file.

.

Download the upggrade file:

For 3.6.60 Version: Download Link

For: 3.6.60 Above Version: Download Link

.

Upgrade Method

1. Upgrade the IPC via NVR system

（1）Please download the update file to your computer and unzip it, then copy the update file(IPCAKV3C_xxxxx.rom) to a USB flash drive. Please note: Don’t change the file name

（2）Plug the USB flash drive to the NVR’s USB interface

Enter the NVR’s menu (System Setup-> Channel Setup-> IPC Upgrade)

.

.

（4）Click the “Channel” and select the upgarde channel of the IPC.

.

（5）Click “Start” and “Yes”, the IPC will be upgrading. Please note: During the upgrade, please don’t power off the NVR and the camera.

.

.

（6）If the camera upgraded successfully, the Status will show “Success!”.

.

.

2. Upgrade the IPC via TF card.

.

.

（1）Unzip the upgrade file, then copy the “help.rom” file to the TF card. Please don’t change the file name and move it to the root directory, do not move the subdirectory.

（2）Power off the camera, then insert the TF card to the TF card slot. Then power on the camera.

（3）Waiting for about 1 minutes, the camera will start up. Then press 3 times continuously of the reset button for the camera(In order to prevent operation errors, you can press several times, which will not affect the upgrade).

（4）About 2 seconds later, the camera will makes a sound for an upgrade. Then waiting for about 2-3 minutes, if the camera restart and works normally, it means that the upgrade is successful.

New Manual for Dual light

Click here to download

If the IP camera doesn’t work with NVR system,please check …

1. First of all,please confirm both of the camera and the NVR are powered on .

(1) Camera is powered on: Please plug the power adapter to the camera ,and then cover the IR-Cut with your hand (See picture), finally to check if the night vision will be activated or not .

(2) NVR is powered on : Please plug the adapter to the NVR ,and then see whether the power indicator is on.

.

.

.

.

2. Secondly please enter NVR system — Video Manage ,and check if the status of camera is connected successfully or disconnected. 

.

.

.

3. Thirdly, if the camera is disconnected,please confirm the distance of the camera and NVR system. The far distance will affect the signal transmission.Please follow the below steps to fix the issue:

.

(1) . Please enter NVR system —  Video Manage — delete camera (The same page as the Step 2)

(2). Remove the camera and take it next to the NVR system,and prepare a network cable and start to match code for the camera and the NVR.

(3). How to Match code :

A. Connect this camera to the NVR via Network cable.

B. Right click mouse on the main interface, select “Video Manage“

C .Click “Refresh“, find the camera’s IP. Click “Match Code“, then click “Yes“, the NVR will start to match code to the camera.

.

.

D. After matching code successfully, the “status” will show “Connect success“.Then you will see the camera is added to the NVR and display video on the screen.

.

4. Finally, you could unplug network cable and put the camera to the place where you want .

How to change the channel

.

.

1.Please click “Video Manage”.

.

.

2.Make a note of the camera IP address you want to change.

.

.

3.Click “Manual Edit” and enter the IP address on the corresponding channel.

.

.

How to fix black screen Monitor for 10” /15.6”NVR

click here to download the operation video

.

How to get the NVR system ONLINE?

.

1. Please make sure you enabled DHCP of your Router.

2. If you don’t know how to enable the Router’s DHCP,

    please input the IP Address of your Router to your computer browser,

    then you will find the network information, you can enable the “DHCP”.

3. After that, please plug a network cable to the WAN port on back of NVR.

4. If the system refuses to go ONLINE?

Basic troubleshooting:

  (1).  Check if your network cable can work well.

         If NVR is getting signal, there should be flash light. If not, please check the connection and cable.

  (2).  If the port is right and NVR is still OFFLINE, then it should be DHCP issue.

         Enable DHCP on your NVR.

        Click right button of mouse, go to NVR’s System Setup – Network Setup – check the DHCP and enable it,

        apply and save it. Wait for 1 minute to see if the status on bottom right corner changes to ONLINE.

5. Or you can go back main menu to select “Fast Network“, 

        Then the system will connect the WAN network automatically.

        Within 1 minute, you shall see NVR status changes to ONLINE and the NVR is ready to be viewed

        from anywhere anytime.

6. If this can’t help you, probably your Router disabled DHCP or block new devices from connecting.

    What DHCP does is: when Router find new device connected, DHCP allocate new IP to the device

                              and connect it to the Internet.

   An easiest way to know if your router enables DHCP:

   When you connect a new device to your WiFi for Internet service (or a visitor/ friend wanted WiFi

   connection), does it require WiFi password only? If only password required, then your router has

   DHCP enabled; if that requires not only password but also some settings, then your Router is secured

   from connecting new devices. Please ask people who secured the WiFi (who set password) to enable

   the NVR to connect.

The Step 4 and Step 5 should enable 95% users to get NVR ONLINE.

Even if the status shows OFFLINE after all this, we suggest you to use APP and access the Cloud ID

to see if it works.

Note:   Always wait for 1 minute after any change.

.

Advanced troubleshooting

If the basic steps above does not solve the issue. Follow below steps to do further troubleshooting.

1. Make sure the cable you connect to NVR has Internet access. 

Please use a laptop or any PC has RJ45 port

· Disable the wireless connection of laptop.

· Unplug the network cable from NVR and plug it into the PC, see if the PC can access the Internet via the cable.

· If it does, then the cable is good; if it does not, change a cable.

· If cable is good yet no Internet connection, please ask help from your network administrator

· to give the cable Internet access.

2. Enable DHCP of your router, please refer to Step 2.

.

If you don’t want to use DHCP, or you want to set up a static IP Address for your NVR system,

you can follow the below steps to set up:

   Well, we can allocate IP manually for the NVR and connect it to Internet. 

  1. Know your router gateway. 

  This is the IP that goes to the menu of your router. 

  This will vary slightly from manufacturer to manufacturer, and will be listed in the documentation.

  Here are some common IP addresses for various routers:

   Linksys, 3Com, Asus, Dell, US Robotics: 192.168.1.1

   Qwest (AKA CenturyLink), DLink, Netgear, Trendnet, Senao: 192.168.0.1

   Belkin, Microsoft, and SMC: 192.168.2.1

   Apple: 10.0.1.1

If you have misplaced your documentation, and you do not see your router listed here,

search on Google for your router name and “default IP address” to find the correct information.

Another way to locate your router’s IP address: on a PC, open the command prompt (click on Start >

Run/Search for cmd) and enter ipconfig. Look for the Default Gateway line, and try that number.

On a Macintosh, open the Network control panel (System Preferences…, Network) and look for Router: 

This is your router’s IP address.

2. Go to NVR’s System Setup Network Setup

How to switch wireless connection to wired connection

.

.

1. Please connect IP camera to NVR by net cable

2. Checking the Network setup of NVR, remember the network segment of the IP address with NVR

.

.

3.Right click mouse, Enter into VIDEO MANAGE

.

.

4.Click Refresh, search the IP address of camera which connect to NVR

.

.

5.When you find the IP camera on NVR, please click Modify, revise the IP address of camera to the same network segment with NVR

Please noted: The IP address of camera can’t conflict with the IP address of other devices

.

.

.

.

Click Yes to save

.

.

Double click the IP address, the camera will connect to NVR automatically

.

.

6. After setting the IP camera, connect NVR and the IP camera to the same router by net cable, Refresh NVR, search for the IP camera, then add it to NVR, in this way, the IP camera will connect to NVR by wired

.

When 3MP IPC is added to NVR, it prompts “resolution too big”

.

.

When adding a 3MP camera to the NVR, if the “resolution is too large” prompt appears.Please modify the NVR resolution, the detailed operation is as follows:

.

1.Please click “Video Manage”.

.

.

2.Select the camera that appears “Resolution too big”, and then click “Channel Setup”.

.

.

3.In “Channel Setup-Encode setup”, modify the resolution to 1920*1080, and then click “Apply” to save the settings.

.

.

4.Disconnect the power of the camera and restart it, after adding the camera, the camera can be used normally.

.

.

Dual light and AI function setting instructions

Click here to download

.

iSmKit CMS user manual

Click here to download

.

How to upgrade the 8CH NVR to 10 Channel(Only for Version 3.1.8.0M)

.

.

1. Comfirm your system version if is the version 3.1.8.0M first. 

Note: This update file only supports NVR version(3.1.8.0M) to update to 10 channel, if your system version is not 3.1.8.0M, please don’t use this update file to upgrade your system, otherwise it will cause the system not work.

.

Go to “System Admin” – “System Version” to check.

.

2. Download the upgrade file to your computer. Click here to download

.

3. Unzip the upgrade file via rar or zip, then plug the USB flash drive, and move the unzipped update file to the root directory of the USB flash drive. 
Note: 
1)Please move the update file to the root directory of the USB flash drive, do not move the subdirectory.
2)Do not change the file name.

.

4. Connect USB-disk to the NVR.

.

5. Enter the NVR’s menu (System setup\System Admin\System upgrade), Click “Start” to begin upgrading.
Note: Please keep power supply well during the upgrade.

.

6. Once the upgrade is done, NVR will restart system automatically.

.

Effective Troubleshooting for Non-Functional 16-Inch Monitor

Effective Troubleshooting for Non-Functional 16-Inch Monitor

.

.

Youtube Video: https://youtu.be/QVtIkMScO0Q 

.

1. If the indicator lights in the bottom right are OFF, replace the monitor’s 3A power supply.

.

2. If the indicator lights in the bottom right are ON, but the screen is black, check the screen cable.

.

.

.

If the display shows “Power Saving,” there are two possible scenarios:

.

3. For “No Signal → Power Saving”:

When there is no signal, immediately press the “Auto” button. This will bring up the signal source selection menu. Use the “←” or “→” keys to navigate to the first option (“Auto select”), then press the “Menu” button to confirm.

.

4. For “No Cable → Power Saving”:

Please check the two connecting cables in these locations.

.

.

<p>The post EseeCloud Devices Advanced User Guide first appeared on NVR IPCAMERA SECURITY.</p>

Safety Caution

All PRODUCTS & PARTSThis product may require cabling,we suggest to test all products&parts before installation and cabling×Dismiss this alert.

Nvr product description

1.  WIFI Antenna Ports:Double antennas to WIFI range

2. WAN Port:Connect your NVR to Internet

3. VGA Port:For viewing on VGA monitor

4. HDMI Port:For viewing on HDTV

5. USB Ports:For mouse and backup

6. Power Input

IP Cameras product description

①. WiFi antenna:WiFi connection with NVR；
②. DC Port:input power 12V 1A;
③. Reset Button:press reset button for 10 seconds to restore factory setting and enter into matching-code mode;
④. RJ45 Port:for pair the camera with NVR,or connect the camera by wired connection

Note:Working temperature ranging from -13 degrees Fahrenheit to 122 degrees Fahrenheit.

Installation Instruction of WIFI NVR KIT

EseeCloud Wireless Security Camera System Installation

Read More : Wi-Fi NVR Kits User Manual

Note:The NVR can work with the router by wireless connection and wired connection Wired connection: when your NVR connect by RJ45 to your router,it will get network settings automatically Wireless connection: right click your NVR mouse and choose System Setup→Network Setup→Wireless Internet→Enable the Wireless LAN→find your own wifi network,and put wifi password here (pls notes it doesn’t work with 5G WIFI network)×Dismiss this alert.

Setup The System

This system is standalone with embedded Linux Operating System in the NVR. Just like a desktop PC, need to hook a screen to the NVR to enter the OS .Any TV,monitor with VGA or HDMI input should work for it.

If you connect the NVR with monitor shows Hiseeu logo or shows black,normally it is your monitor resolution is lower then the NVR.You can press the left side of the mouse for 30s,then it will reboot.

If still can’t work,pls change a monitor,thanks.

When you turn on the NVR box, the monitor will get below interface: Setup Wizard- -Down- -General setup- -Next -wireless setup- -Next- -Fast network- -Next -Format the hard drive- -Next

CHECK NVR NETWORK , CHANGE NVR SYSTEM LOGIN PASSWORD

Once you have completed connecting the NVR,wait approximately 2-3 minutes.Next you will see the window below on your monitor screen.For your first time to login in,User name is admin,there is no password,just choose ok to get into the menu.
(if you forget the password,pls find the solution on the FAQ page)

Tips: To protect your privacy,please set your password at earliest convenience(don’t set the password over 8 characters).Right click the mouse→System Setup→System Admin→User to set password.

How to check if your Cloud is online and Network status is healthy ?

Right click the mouse of the register,choose Fast Network.In the middle of the window you should see Cloud status as ONLINE and Network Status as Healthy Network.

If this does not appear, select Manual Config then enable DHCP,Click Apply,then power off the NVR box,wait a few seconds and power up.

Once you power up, repeat the steps outlined as above.Cloud status must be ONLINE and Network Status must be Healthy Network.If this does not happen,you will not be able to view remotely

Menu Do What

Menu bar

Split Screen: change status of live view.You can choose to view multiple cameras or any single camera.

Video Manage: manage IP cameras and NVR channels.

System Setup: all system settings.

Video Playback: playback recorded videos.

Video Backup: backup recorded videos.

Color Adjust: adjust the image setting of the each camera

PTZ Control: control PTZ camera

Volume: Adjust volume of audio cameras(works only for audio cameras).

Setup Wizard: step by step guide of 1st time general settings.

Fast Network: shortcut to network settings.

Wireless Add: add IP cameras into NVR channels wirelessly.

Exit System: logout,reboot,close screen output and shut down the system.

System Setup

Click right button→Choose System setup; enter the menu that enables you to do all settings related to this system.

Menu Do What

There are 3 modes for reocrd.

Note: Users can setup any period of time they want,for example 0:00:00-23:59:59,That’s 24 hours×7days recording.When NVR detects hard disk,the default setting will be 24 hours×7 days recording.

The priority of Alarm is higher than that of Motion,and the priority of Motion is higher than that of Time.

Video Playback

Steps: right clik mouse in main menu→Video playback→choose date,channel,record mode→click search→then can view playback file.(IE browser can’t check the playback directly,so you can use the Eseecloud software on computer or check on your phone app Eseecloud and IP RPO)

Warm prompt:

1.IIIustration for playback button: play, pause, fast forward×2,×4,×8

2.Play file:Choose the recording file in file list,as number “1” shown in picture.Choose one of the recording,click “play” to play to recording file;

3.Video backup:Choose the recording file in file list,as number “1” shown in picture.Insert the U flash disk,click “video backup” to backup the file;

4.Timeline: Click “date”and “time”at left bottom to check the timeline of recording,as number “2″ shown in picture;

5.On the timeline with recording file,left click the mouse,the can playback the file.

Notes: you can see four channel cameras playback at the same time,if you want to check other channels you need select the correct channel at first,then choose search to find it playback.

How to Backup the video

Use U disk to copy video,so easy and convenient!

The playback files is avi. format, you can use VLC player to check it on your computer VLC player.
download link: https://www.videolan.org

View on PC via lE or Eseecloud and Phone APP Eseecloud or IP PRO

To View on the the PC

To view on browser,you have to connect the NVR and your computer to the same router.Enter the IP address of NVR on the browser’s address bar.(We recommend using IE or Micorosoft Edge) Right click the mouse→system setup→Network Setup→IP address (Start with 192.168… )
You can change language on the right top corner.

To view on Eseecloud software on PC

Input Cloud ID (Right click the mouse→fast network→Cloud ID)
Input User Name and Password (If you doesn’t change the user name and password,User Name is admin ,no password)
please download Eseecloud software from： https://ipproapp.com/computer
user name is admin,no password,choose login

*Select “Add”
*Select “Cloud ID”.enter the cloud ID(9 or 10 numbers).You can find it on your home monitor screen.
Or right click the mouse, choose Fast network find cloud ID here
* Username is NVR system user name on your home monitor screen
* Password is your NVR system password on your home monitor screen.(If you don’t change It in your setup,it should be no password)
* Channels: Input 4 or 6 or 8. If you have 4 cameras,enter 4 etc.
* Click Confirm and you will see the video.

if you check in the local network,you can use the NVR IP address to add the system (Find the IP address on Fast network page or Network setting page)

To View on IE browser

Find the IP address: right click your mouse and choose Fast network, you will see the IP address here.
Enter the NVR’s IP address in your IE browser for example: http://192.168.1.105(If the default WEB port 80 has been changed e.g. to 100,you need to add new port number when input IP address in the browser,for example: http://192.168.1.105:100).

To view on the Phone

Users can use cellphone to scan the QR code below to install the APP free of charge,or users can search “Eseecloud”or ’IP PRO‘ on APP store or Google Play then install the APP.

Click “+”→other ways to add/ scan the QR code on your fast network page→Network connected device→input Cloud ID and User name and password (user name and password is the same one you login in NVR)

Tips: if you’ve set a password on your NVR system,please update your password on APP to view.
And if your camera loading for a long time and don’t show image,you can right click your NVR mouse and choose System Setup→Network setup,change the MTU to 1000.

Playback On Mobiles

In the Eseecloud APP,while viewing live video of the system,click Playback,you will enter the remote playback menu.The APP Playback only check one channel at one time

Tips: Videos in playback are HD mode for real time which requires very good transmission condition.
We suggest to playback in LAN.Remote playback out of LAN may not 100% work due to connection & network condition.

Extend WIFI Range

Wireless connection is easy and convenient, but it’s not universal application. Because of the character of WIFI, the WIFI signal will decrease when going through some obstacles Some methods can be applied to bypass obstacles and extend WiFi range.

Position The Antenna Correctly

WIFI range is like an apple and the antenna of NVR is in the center of it.WIFI signal is strong all around the WIFI range.Antenna of NVR should be put straight up,if not,WIFI signal will be weak.
According to the signal transmission character of antenna, the antenna of cameras should overlap or parallel to NVR WIFI range,as pictures showed below:

Use Antenna Extension Cord to prolong WIFI distance

Installation method of antenna extension cord

Note:When WIFI signal is not strong enough against walls,users can take off the original antenna and subtitute antenna extension cord.Drill a hole on the wall to let the extension cord go through and simply it where WIFI signal is strong.

Set up cascading connection in a reasonable solution,extend wifi signal transfer distance

Note:
Repeater function can’t strengthen WIFI signal for wireless NVR kit, but can extend the distance by repeaters→WIFI cameras.

Only when the repeater cameras and repeated cameras are positioned correctly,WIFI distance will be extended.

Repeater function and 3 meters antenna extension cord are two methods to extend WIFI range.
Users can choose one according to real situation.

Repeater Setup

Step 1. Right click the NVR mouse,and choose “Video Manage”- -then left click Repeater”

Step 2. Add repeater
As picture shown below,click icon + besides channel 3,choose other channel.

Step 3. As picture shown below, it means IPC1 is connected to NVR through IPC2 and IPC3.
IPC2 is connected to NVR through IPC3.IPC3 is connected to NVR directly.

Step 4. Click “Apply” and then click “refresh” to check if the setting is successful.

Delete Repeater

Move the mouse to targeted channels,left click to delete,and then click “Apply” and “OK”.

Application Example

As picture shown above, when IPCAM1 is put somewhere is out of NVR WIFI range,and there is IPCAM2 between them with strong WIFI signal,users can put IPCAM1 close to NVR and power it, setup IPCAM1 repeated by IPCAM2, and then install IPCAM1 to the presupposed place.

Camera add failure reasons and solutions

Q1: Failed to add the camera for the first time

Check whether the green light of the camera flashes normally. If the camera status light is not flashing green, use a thimble to lightly insert the configuration hole or long press the reset button until the camera indicator flashes.

Q2: Determine whether the binding failure caused by the router settings

1. The router has been set up to prevent Wi-fi squatter If the Wi-Fi connected to the camera is set to prevent Wi-fi squatter(black and white lists, MAC address filtering, etc.), the camera will not be able to connect to the Internet. The router’s prevent Wi-fi squatter settings need to be canceled.

2. The router is set up with 5GHz band wireless WiFi The camera does not currently support the connection of 5G band WiFi. Please open the router management page (generally marked with the address of the management page on the bottom label of the router), select the wireless setting 2.4GHz, and set it to on.

Q3: Check whether the mobile phone prohibit the permission of  EseeCloud to use data, WLAN, GPS

Domestic Android phones may prohibit the use of data, WLAN, GPS permissions for this application, resulting in the camera being unable to connect to WiFi. Solution (Android phone): Open the phone settings center-click “application management”-open the above permissions

Q4: Make sure that the WilFi account and password are filled in correctly

It is likely that the Wi-Fi account and password you connected to the camera are incorrect, resulting in the camera not being able to connect to the network. In particular, pay attention to whether there is a space input, and try to avoid complex and uncommon symbols.

Q5: Other questions

1. If the router is set to bridge mode, the WiFi signal will be unstable, causing the connection to fail. It is not recommended to use WiFi in bridge mode when the camera is networked.

2. If you are a campus / enterprise user and the school 1 company assigns each student / employee a static IP to access the Internet, you can manually enter the static IP information to access the Internet.At present, this situation is not supported by camera networking, need to select other available WiFi connections.

3. The camera does not support WPA / WPA2’s “enterprise” encryption method to connect the camera to the network. Support WEP, WPA–PSK 1 WPA2–PSK, or corporate WiFi without password. If the camera is networked in the corporate network environment, please confirm in advance whether the WiFi encryption method meets the camera networking requirements.

What should do if the camera is offline?

Q1: Camera offline processing method

1. Check whether your device is power-on and the status light is on;
2. If you are using WIFI connection, please confirm whether you have modified the WIFI in the environment where the device is located-including the WIFI password and name, if modified, please reconfigure WIFl;
3. If the reason cannot be resolved, please restore the factory settings and add the network again.

Device preview help

Different devices support different functions. Preview interface only shows the functions supported.

Light control:setup on/off,brightness,color temperature for light control device

Screenshot:snapshot current preview image

Recording: record current preview video

Full screen:tap button and switch to landscape viewing

Calendar:choose playback time to show all recording files wanted

Remote playback: device must to be inserted TF card.

Two way talk:press the button and talk for a long time

Installation mode:swith to wall installation and ceiling installation mode

Display mode: at ceiling installation mode,there have fisheye mode,cylinder mode,corridor mode and fulI screen mode

Cruise: setup auto cruise .

Sound:setup the sound on/off

Swith code stream:switch HD and SD

Split screen dispaly: choose screen channel number

Screen aspect ratio: can set the screen aspect ratio

PTZ control: control the movement of high speed dome

Timeline:drag the time line left and right to choose recording period . Use fingers to zoom in or zoom out the timeline

Add Camera

Add device

Method 1: Enter to device list interface after login, click the t’ button in the upper right corner of the interface, and select the add device” button.
Method 2: Click the’+’ button in the interface to enter directly to add device interface.

add camera

1. There is a QR code on the device body:
Scan the QR code on the device,display the device ID of the current device , click the Add ICON below jump to the prompt interface of operation guide.

add cameraadd cameraadd camera

2. Can’t find the device QR code :
lf there is no QR code on the device, click ‘Other ways to add’ and then select ‘Standalone camera’.

add cameraadd cameraadd camera

3. Please connect your mobile WiFi to the device hotspot.

Open Settings-> Select Wireless LAN > Select ‘IPCXXXXXXXXX’ device hotspot.

Connect hotspot,default password：11111111

add camera

4. After connecting successfully,return to APP.

Remote View: View video via WIFI or other network, please select Remote View.(most people choose)
Direct Connection: View video without network ,select Direct Connection. (few people choose)

5. Select Remote View to continue.
Select your wifi and enter your wifi password, then click Confirm .

add camera

add camera

6. Configuring, do not unplug the network! The network configuration process may take 1-2 minutes, please be patient.

add camera

7. Set device name and device password.
For added security, please set a password.

add cameraadd cameraadd cameraadd camera

Device Sharing
Generate shared QR codes ln the device list, click the “Share” button, set the right to share, choose to share, and generate QR codes.

Device SharingDevice SharingDevice Sharing

Scan and share QR code.
click on the’+’button in the upper right corner of the interface to enter to add device interface, click on scan add device, enter to scan interface, scan shared device QR code, after display the scan results then return to device list interface.
Note: You need to allow access to the camera and album to use this function properly.

Scan and share QR codeScan and share QR code

App Operation

Log in

This APP support “account log-in”, third-party log-in” and local experience”.
Account log-in: At log-in interface, input user name/cellphone number/email address and password, click ‘0K” and log in.
Third-party log-in: Click the icon of third-party network social software, authorize the APP to log in.Local experience: Users can use the APP without log-in.
Remember the password: Supportremem-berring the account and password that have been logged in, which is convenient for switching account login.
Note: Please pay attention thatLocal experience” mode will be stored at local.Once data is lost, it can’t be restored.

IP PRO Log in

Registration

Input cellphone number/email address to register, get verification code.
Input verification code and password, click “OK”. After registration it will move to device list.
Note: Each cellphone number/ email address can be used for registration once.

IP PRO RegistrationIP PRO Registration

Reset Password

Input registered cellphone number /email address to get verification code. Input verification code, reset password and click “OK”.
Then go back to log-in interface, log in with new password.

IP PRO Reset Password

Frequently Asked Questions

Question one：After installation, open the CMS and display “Cannot load plugin”?

Answer one：

1.Please confirm whether the installation path uses Chinese when installing, and the plugin is temporarily not compatible with Chinese path.

2.After confirming the non-Chinese path, if the problem persists, you can contact technical support for assistance.

Question two：After connecting multiple channels of video (more than 30 channels), videos stop for a few seconds , all channels are automatically disconnected into the black screen. The device connected again has no response. Do we need to restart the CMS?

Answer two：The new version of CMS3.0.1 runs with higher memory. If you connect many channels by the lower configuration computer, the computer system will run out of memory, causing the CMS to run abnormally. If the computer configuration is slightly lower, it is recommended not to connect too many channels. The optimization work has been planned for this situation.

Question three：When CMS is installed on the OSX system, it displays “File is corrupted” or “Unable to open” when it is opened?

Answer three：

1.Open “System Settings” → “Security and Privacy” → “Allow applications to be downloaded in the following location”, check “any source” (applies to versions prior to OSX10.12.X);

2.Open “Terminal”, enter the string “sudo spctl –master-disable”, press the “Enter” key, enter the sudo password (applicable to versions after OSX10.12.X). If the above method still does not work, please contact us to help you solve it.

Question four：After starting a window and flashing, it will not start or XP will appear. Open the software to indicate 0a00000000 memory referenced by 0x00000000 instruction. The memory cannot be ‘written’.

Answer four：Large probability video card driver problem, update the graphics card driver can solve

Question five：It shows  mfc100u.dll lost when opening computer

Answer five：Install VC++2010 library to solve the problem

More features

User Management

New user：①Click New User ②Enter username (required) + note name (optional)③Click to confirm

Modify permissions：

Default: The default permissions include screenshot, video, PTZ settings, video playback, remote download 5 items

modify：①Click edit permission ②Check the permissions and devices/channels that need to be assigned to new users (you can click to select all) ③Click to confirm

Other functions：

        ①Clear password: If the login password of the new user is forgotten, you can log in to the newly created user again by directly clearing the password and the internal setting data can be retained.

        ②Modify the note: Add a note, change the note or delete the note, go to the modify note operation

        ③Delete user: If you feel that the newly created user is not necessary, click delete user to delete the user.

New userModify permissionsModify user

Log query

Inquire：①Confirm ‘start time + end time’②Confirm ‘log type’ (including: alarm log, login log, operation log)③Selected area ④Click to query

Log query 

Resource management

Screenshot：

search for：①Select ‘start time+end time’ ②Click search

Preview：①Method one selects ‘preview’ for right-click operation ②The second method is the screenshot file retrieved by direct click.

delete：①Method 1 Select ‘Delete’ for the right-click operation. ②The second method is to enter the screenshot preview state and click to select ‘delete’.

location：①Method 1 Select ‘Open location’ for right-click operation②Method 2 is to click ‘Save Location’ in the resource information.

Resource information：‘user, resource size, resolution, device name, associated channel, screenshot time, save location’, including the above content (as shown in Figure 2)

Replacement size：‘Original size, maximize, zoom in, zoom out, resource information, delete’, the screenshot preview status includes the above status/function that can be switched to

video：

search for：①Select ‘start time+end time+’②Select the recording type (including: preview video, playback video, default all types)③Click search

Resource information：‘user, resource size, recording type, device name, associated channel, recording time, save location’, including the above

Other functions：The operation steps of ‘preview, resource information, location, delete’ function are the same as the screenshots. For details, please refer to the operation in the screenshot.

Right click operationResource information

System Info

Version Information：The content is displayed as follows ‘version number, date’

change Password：①Enter ‘original password + new password + confirm new password’②Click to confirm ③Re-login verification password

sign out：Click the ‘Exit Login’ button to quit the login status of the current account.

System Info

User parameter

Basic Settings

Split screen number：The selected split screen number is displayed after the re-login, and the CMS provides split screen 1/4/6/8/9/16/25/36/49 nine forms of choice.

Display language：CMS currently defaults to 9 display languages, such as Simplified Chinese and English. When you choose to log in again, you will switch to the corresponding language.

Login Method：The cloud login mode is online. You need to connect to the external network when you log in. The local login does not have this hard requirement.

List style：The list style includes tree shape and graphics. The replacement is only the real-time preview interface and the display of the device list under the playback interface. The device list under other interfaces is unified into the tree list style.

Path modification：

①Screenshot path: The screenshot file is saved in the snapshot folder by default, and can be saved in other paths according to its own needs.

②Local recording path: The local recording file is saved in the record folder by default, and can be saved in other paths according to its own needs.

③Video download path: The files downloaded by the playback video are saved in the video_download folder by default, and can be saved in other paths according to their needs.

Preview sync time：Check the time when the device is previewed and the computer will be automatically synchronized (only ipc is supported)

note：After modifying the settings, click “Finish” and you will need to log in again. (It is best not to modify it to a directory containing Chinese)

advanced settings

Time zone setting：The local time zone can be selected according to the actual situation.

Automatic lock：Check the auto lock and enter the integer in minutes in the time frame. If no operation is performed on the CMS within the time of the input, the CMS will automatically lock.

Automatically connect video：After logging in to the auto-connect video, log in to the CMS and automatically connect to the device added to the device list. The number of connected channels is the number of split screens in the basic settings.

Basic Settingsadvanced settings

Equipment management

Add device

Add a LAN device：①Enter the device management interface ②Refresh LAN device ③Check the device and click Add (LAN device can be filtered by entering IP/ID in the filter box)

Add cloud ID device：Manually enter the device ‘cloud ID number + channel number’, select ‘type’ according to the actual situation of the device, and the rest can click to confirm (the password can be selected according to the actual settings of the device)

Add an IP/DDNS device：Manually enter the device ‘IP/DDNS+port+channel number’, select ‘type’ according to the actual situation of the device, and the rest can click OK.

LAN add

Modify device

Device modification：In the device management or preview interface, after selecting the device and clicking Modify, the device interface will be loaded.

Regional modification：In the modify device interface, click the area drop-down box.

Group modification：After selecting the group under the device management interface, click the modify button to load the modified group information interface.

note：Modify the channel name, panorama, and channel type corresponding to the channel number in the device.

The panorama or channel type corresponding to each serial number is independent.

The channel device in the device needs to be in the panoramic state. You can select the corresponding channel serial number to modify the panorama. And channel type

Device modificationGrouping

Remote setting

VR CAM/gateway Remote setting

Setup steps：①Selected device ②Click Settings / Connect Device and click the Remote Settings button (as shown in Figure 1)

Device Information：Content includes device model, device ID, OEM serial number, firmware version (providing check updates)

Function setting：The audio, prompt tone, prompt language, and display mode and resolution can be set on the configuration.

Alarm system：The content includes motion detection, message push, motion detection sensitivity, and synchronization time function. If daylight saving time setting is available, you can set daylight saving time.

TF card settings：TF card status, available / total capacity, TF card formatting function

note：

①Alarm message push is not supported in local login. You need to check to switch to cloud login status.

②Currently supports VR CAM/gateway devices for remote setup

Remote setting interface

D82 series NVR remote setting

Setup steps：①Selected device ②Click Settings / Connect Device and click the Remote Settings button

Device grouping

Create a group：①Click the ‘Create Group’ button ②‘Enter the content in the group name box and click OK.

Add channel：

enter：①Select the created group ②Click the Add Channel button

Import selection：①Selected channel ②Selected group ③Click the import selection button

Import all：①Selected group ②Click to import all buttons

Modify/delete：

Edit: Select the group and click the Modify button to modify it.

Delete: delete the selected group or channel and click the delete button to delete

Create a groupAdd channelModify group

Video playback

Video playback

Playback four steps：①Select device channel ②Select video type ③Select playback date ④Confirm search video

Device channelVideo typeDate selection

Timed playback

Timed playbackTimeline

Video sync

Steps：①Retrieve video  ②Check sync  ③Switching time point

Video download

Batch download：Enter the time period to be downloaded at the start time + end time according to the needs of the retrieved recording time range.

Time period download：The time period of the video recording will also be displayed in the download resource. Click the download button for any time period according to your needs.

Custom bulk downloadSelect time period to download

Other functions

Playback control：Support playback/pause/stop control in video playback, select the screen form in playback and click operation

Time scale adjustment：The settings in the Setup Wizard are not set. The playback timeline scale will default to 60 minutes. You can also modify the scale value by clicking ‘Reduction’ or ‘Magnify’ during video playback.

Playback controlAdjustment scale

Live Preview

Connection/Disconnection

The list style is treeshape:

connection：

①Double-click on the selected device/channel to enter the connected video state.

②After selecting the device/channel, right click and select “Connect Video” to enter the connected video state (Figure 1)

disconnect：

③Double-click to disconnect the current connection after selecting the connected device/channel

④After selecting the device/channel, right click and select ‘Disconnect’ to disconnect the current connection.

Figure 1

List style is graphic：

①After selecting the device/channel, click the play button on the device list to enter the connected video status.

②After selecting the device/channel, click the stop button on the device list to disconnect the current connection status.

③Right-click operation connection/disconnection is consistent with the tree list style. The specific operation can be referenced.

Note：poor performance of the computer will directly affect the smoothness of the preview video. It is recommended that the number of channels connected to the device be gradually increased

Video/screenshot

Video：

①Click the Record button on the toolbar to enter the video recording status (as shown in Figure 1 below)

②After the video operation, click the record button again to stop recording.

Note：

①The actual recording duration is not equal to the time difference between the start recording time and the end recording time.

②If the device network is interrupted, the recording will succeed but no video file will be saved.

③The channel is maximized or minimized during recording, and the recording will stop.

Screenshot：

Click the screenshot button on the toolbar to enter the screenshot status (as shown in Figure 1 below)

Note：

①If the switching stream video is not loaded, the screenshot operation will be saved.

②The screenshot does not have the function of continuous screenshots. Clicking the screenshot button once will capture an image.

Figure 1

Panorama mode

enter：

①Double-click the channel screen to enter the maximized state, right click and select “panoramic mode” to switch to the panorama mode, enter the panorama, and the code stream is automatically switched to HD.

②The channel screen is in 1 split screen mode, and the panorama mode option is available on the right toolbar. Click to select to switch the panorama mode.

drop out：

①Click on Panorama mode on the right toolbar and select ‘Exit panorama’ to exit panorama mode

②Exit the panorama mode by exiting the screen from the split screen state.

Panorama modeCylindrical modeExpand modeSplit screen modeQuad screen modeSix-screen mode

Note：

①In the local login mode, you can select 6 display modes in the panorama mode, including: panorama, cylinder, expand, 2 split screen, 4 split screen, 6 split screen

②In the cloud login mode, you can select 4 display modes in the panorama mode, including: panorama, cylinder, split screen, quad screen

        Suspension: the direction of the cruise is clockwise

        Wall-mounted: the direction of the cruise swings left and right

       Speed: Cruise provides speed 3S / speed 40S / speed 60S three options, corresponding to slow / medium / fast three speeds

       Stop: Pause the current state of the cruise, left click on the channel in the cruise or select the stop cruise button in the cruise mode to click

Panorama modeInstallation modeCruise mode

PTZ control

Cruise / PTZ / Zoom / Focus / Aperture / Preset：

The PTZ control function can be used only when the PTZ device (such as a ball machine) is connected to the main control device (such as NVR or DVR).

Cruise is to directly perform the screen cruise operation. The pan/tilt is to adjust the lens direction and zoom to replace the mirror multiple.

PTZ speed level controlcontrolZoom, focusPreset

①：Adjust the PTZ control speed (default level is 6)

②：Adjust lens direction and cruise

③：Adjust the zoom and focus of the PTZ camera

④：Set and call the set bit, adjust the lens to the specified position, set the preset position, input the preset position later, click to call, the lens will automatically move to the specified position

Split screen number

When the number of connected device channels is greater than the current number of split screens, the displayed split screen will automatically increase, reaching 49 split screens.

Split screen number

Other functions

Other functionsIntercom

User login

Local login

①Enter account + password  ②Click to login

Login accountforget password

note:

Cloud login

Note:

①The cloud login should be logged in with the registered account (the account registered by the mobile app can be logged in)

②Registered account is recommended to use a valid mailbox, easy to retrieve passwords and other special circumstances

③After registering an account, you need to log in to the email address you entered during registration to activate the email address (click the received link to verify)

④The mailbox status is not activated, and cannot be retrieved after forgetting the password (activation period is two days)

⑤The first time you use EseeCloud_CMS, the software’s time zone will automatically sync with your computer, and you can change it later in the advanced settings.

Login accountRegister a new accountRetrieve password

Installation login

Installation and operation

Step 1: Run the EseeCloud_Setup_3.0.1.exe installation package

Step 2: Select the display language when installing

Step 3: Read and determine whether to accept the agreement

Step 4: Determine the path to the installation

Step 5: Installation is complete and you can choose to run immediately

1. Running program2. Choose a language3. Reading agreement4. Determine the path5. The installation is complete

Introduction to EseeCloud CMS

Function introduction

CMS is called Camera Monitor System. It is a camera monitoring client for online preview image, video storage, remote playback, device management, video/screen download and other functions. 

It is suitable for DVR, NVR, IPC, VR CAM, Wifi IPC and other devices.

Camera suitable for IP PRO, VR CAM, EseeCloud app.