ATTENTION: Prior to purchasing and installing an accessory antenna, read the product specifications of your receiver to determine if your receiver has a weatherproof housing. Installing your weatherproof receiver outdoors provides a better line-of-sight between the receiver and the camera, increasing the strength of the wireless signal. See your product specifications to determine the weatherproof rating of your receiver.

The Directional Wireless Panel Antenna and the Omni-Directional Antenna are used to extend the range of one or multiple wireless or wire-free cameras.

Directional Wireless Panel Antenna (ACCANTD9)

Omni-Directional Antenna (ACCANTO8)

Use the 2.4GHz Directional Wireless Panel Antenna (ACCANTD9) to focus a wireless signal onto one specific wireless device (camera or receiver) to increase the range of transmission. A clear line-of-sight between the antenna and the wireless device needing range extension is required.

Use the 2.4GHz Omni-Directional Antenna (ACCANTO8) to enhance the signal of one or multiple cameras that are paired to a single or dual antenna receiver. You may also use two Omni-Directional Antennas to extend the range of all cameras paired to a dual antenna receiver.

REQUIREMENT: To connect the antenna directly to the camera or receiver, the device must have a removable SMA type antenna. Visit www.lorextechnology.com/compatibility to ensure the antenna is compatible with your camera or receiver model.

Lorex Wireless Cameras and Monitors guide 2024

Also Read  : Lorex Camera Troubleshooting

Recommended Antenna Installation Methods

Your antenna needs will vary depending on the setup of your camera system, the number of cameras that require range extension, and the number of channels on your wireless receiver. Review the scenarios below to ensure you have the correct antenna and installation method to meet your needs.

Click a setup scenario to see the recommended installation method:

Combining Accessory Antennas

If you have installed your accessory antenna according to the recommended installation methods and would like to enhance wireless signal strength even further, you may add an additional Directional Wireless Panel Antenna (ACCANTD9) directly to a camera. The additional Directional Wireless Panel Antenna can be used with a Directional Wireless Panel Antenna or with an Omni-Directional Antenna attached to the receiver.

Click an antenna combination to see recommended installation methods:

Scenario 1: Extend the range of one camera paired to a single antenna receiver

To extend the range of one camera connected to a single channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9).

The Directional Wireless Panel Antenna can be connected in two configurations.

Configuration 1. Connect the antenna directly to the camera

Configuration 2. Connect the antenna directly to the wireless receiver

REQUIREMENT: The antenna connects using an SMA cable and replaces the existing antenna on either the camera or wireless receiver. Check www.lorextechnology.com/compatibility to determine if your product is compatible with the antennas.

Scenario 2: Extend the range of one camera paired to a dual antenna receiver

To extend the range of one camera connected to a multi-channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9). Connect the Directional Wireless Panel Antenna directly to the camera.

Scenario 3: Extend the range of select cameras paired to a dual antenna receiver

To extend the range of select cameras on a multi-channel receiver, use the Omni-Directional Antenna (ACCANTO8).

Connect the Omni-Directional Antenna to one of the antenna ports on the wireless receiver.

REMINDER: Each antenna port on a dual antenna receiver is associated with specific camera channels. One antenna communicates with odd numbered channels (1, 3, and 5), while the other antenna communicates with even numbered channels (2, 4, and 6). See the table below for dual antenna channel configurations.

If you connect the Omni-Directional Antenna to an antenna port and your wireless signal does not improve, try switching the Omni-Directional Antenna to the other antenna port or pairing your camera to a different camera channel.

Scenario 4: Extend the range of all cameras paired to a dual antenna receiver

To extend the range of all cameras on a dual antenna receiver, connect an Omni-Directional Antenna (ACCANTO8) to each antenna port on the receiver.

IMPORTANT: Two Omni-Directional Antennas are required to accommodate this setup.

Combination 1: Combine two Directional Wireless Panel Antennas

If you are using a Directional Wireless Panel Antenna (ACCANTD9) to enhance the signal of a single camera with a single channel receiver, you can use an additional Directional Wireless Panel Antenna to further enhance the wireless signal.

Connect one Directional Wireless Panel Antenna directly to the camera and one Directional Wireless Panel Antenna directly to the wireless receiver. To maximize signal strength, it is recommended to aim the two antennas directly at each other with a clear line-of-sight.

Combination 2: Combine a Directional Wireless Panel Antenna with an Omni-Directional Antenna

If you are using an Omni-Directional Antenna (ACCANTO8) to enhance the signal of multiple cameras, you can further enhance the signal of a specific camera by connecting a Directional Wireless Panel Antenna (ACCANTD9) directly to the camera.

A clear line-of-sight between the Directional Wireless Panel Antenna and the Omni-Directional Antenna is recommended to maximize signal strength.

Lorex SD Pro App: Changing / resetting the password

If the password for the Lorex SD Pro app to view the Wireless Home Monitor is lost or forgotten it will need to be reset.

To reset the Lorex SD Pro app password:

1.Ensure that your Wireless Home Monitor is connected to a network router using the included Ethernet cable.

2.On the Wireless Home Monitor tap the Menu icon ().

3.Use the joystick to select Settings > Network > Reset Password.

4.Select Yes to confirm.

5.Tap the Menu icon () repeatedly until all the menus are closed.

6.Launch the SD Pro app and enter the default password. Refer to your user manual for your default password. You will be prompted to create a new password.

Lorex SD Pro App: Setting up Wireless Home Monitor remote access

You can access and view wireless cameras from a Wireless Home Monitor system using an iPhone, iPad, or Android smartphone or tablet using the Lorex SD Pro app. It is available at the App Store or Google Play Store.

Prerequisites:

To set up the mobile application:

LW2700 Wireless Home Monitor: Included cables and accessories

LW2700 Series Wireless Home Monitors support wireless cameras using a wireless signal. They do not have an internal battery and require a connection to a power source. Refer to your user manual for model specific information on cables and accessories. Click here for downloads and documentation for your product.

Most wireless home monitors include the following cable connections and accessories when purchased:

Network: Wireless camera Internet requirements

Standard wireless cameras that connect to a DVR / NVR, do not need access to the Internet to function. Stand-alone IP cameras do not require an Internet connection for basic functions, but an Internet connection is required for full functionality.

Security Cameras: Understanding Field of View (FOV)

Field of View (FOV) is the maximum observable area that is seen at any given moment through an optical device such as a camera lens. The coverage of the area can be measured using the horizontal and vertical distances to find the diagonal of the area in degrees. Mathematically, the FOV is calculated using the horizontal dimension of the sensor (h) and the Focal Length (F).

You can find the camera’s Field of View details in the Specifications sheet. Click here for additional support content including security camera documentation.

The Camera Lens, Sensor and Focal Length

Focal length (F) is the distance between the center of a lens and its sensor. The size of the lens is the aperture size.

These factors affect field of view. A narrower focal length captures more of the scene and displays a larger field of view. A wider focal length magnifies a scene and decreases the field of view. The higher the focal length value the lower the FOV.

Types of Camera Lenses

Fixed: a fixed camera focal length provides an Angular FOV which is permanently set and cannot be adjusted by the user. Varifocal: the camera focal length can be manually adjusted by the user. Generally, this is done manually with screws or dials. At Lorex we have motorized varifocal cameras that allow you to digitally zoom using your phone or NVR without losing details. These lenses provide flexibility and customization for your camera image needs.

The importance of Field of View

A wide angle lens or smaller lenses produce a greater field of view and captures more objects in a scene enhancing your ability to cover larger and wider areas such as foyers, parking lots or warehouses.

A narrow angle lens or larger lenses produce a smaller field of view; capturing a limited area, but the camera quality image improves in detail. These are designed to monitor a specific object, such as cash registers, entrances/exits, hallways or objects of value.

How to Calculate the FOV

To calculate the FOV requires the sensor size and the focal length of the lens: h = Sensor Size F = Focal Length of the Lens

FOV is represented by this equation: FOV = 2tan-1(h) / 2F

Example: h = 4.7mm F = 6mm FOV = 2tan-1(h) / 2F = 2tan-1(4.7)(12) = 2tan-1(0.39) = 2(21.4°) = 42.8°

W482CAD – 2K Wi-Fi Camera : Frequently Asked Questions

The following FAQ article answers many of the general questions about the 2K Wi-Fi Camera with Smart Deterrence (W482CAD). Where applicable, the FAQ includes links to articles where you may find more information.

.

Where do I place my Lorex 2K Wi-Fi Camera?

.

How should I position my Lorex 2K Wi-Fi camera?

When mounting the camera on a wall, make sure of the following:

 Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

.

How do I enable motion detection and person detection?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap  icon to enable Motion Detection.

Note: If motion detection is disabled, general/person/vehicle detection will automatically disable and you will not receive any motion detection notifications in the Lorex App.

.

How do I customize Motion Zones™?

Motion Zones™ allows you to customize your device’s motion detection region. Motion Zones™ screen consists of the following settings:

To set Motion Zones™

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap Motion Zones™.

 For full instructions on how to set customized Motion Zones™, see Configuring Motion Zones™.

.

Why am I receiving so many notifications?

There are a few ways you can lower the number of notifications you are getting.

.

How do I enable Color Night Vision?

1.Lauch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap  icon to disable Auto Night Vision.
Note: Disabling Auto Night Vision will force the camera into Color Night Vision mode. Recommended in low-light conditions.

.

How to activate Two-Step Verification?

1.Launch the Lorex App.

2.Tap Settings.

3.Tap Account Settings.

4.Tap Two-Step Verification.

5.Tapicon to enable Two-Step Verification.

For detailed setup instructions, see Two-Step Verification Setup.

.

How to optimize video quality?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Video Settings.

4.Tap  icon to enable HDR (High Dynamic Range).

Note: Enabling HDR optimizes video picture in high-contrast conditions such as under-lit and over-lit areas.
By default, the video quality is set to High (2x1080p HD).

.

What is Home & Away™?

Lorex App can automatically use your location to manage your notifications when you are at home or away. The app will notify you when you are inside/outside of your set home perimeter.

To start using this feature, navigate to your mobile device settings and enable Location services for Lorex App.

For detailed setup instructions, see Configuring Home & Away™.

.

How do I activate the LED deterrence light when motion is detected?

1.Lauch Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Deterrence Light Brightness.

4.Tap  icon to enable camera’s deterrence light whenever motion or person is detected.

.

How do I remove the 2K Wi-Fi Camera from my account?

1.Launch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Remove Device.

.

How to permanently delete data of 2K Wi-Fi Camera?

Refer to Formatting Device Storage for more information.

.

Does my device support WPA2 or WPA3?

Your device supports Wi-Fi Protected Access 2 (WPA2) which is the industry standard security protocol for Wi-Fi networks. WPA2 offers security against unauthorized access and data interception and is supported by most Wi-Fi routers including those that support both WPA2 and WPA3. It employs Advanced Encryption Standard (AES), an encryption mechanism, which secures communication between your camera and Wi-Fi network to keep transmitted data confidential. For information on which devices support WPA2 and which devices support WPA3, please refer to “WPA2 and WPA3 Supportive Devices.”

.

What are the compatible SD cards?

Refer to Compatible SD Cards and Storage Sizes for more information.

.

What devices are compatible with the 2K Wi-Fi camera?

Refer to Product Compatibility Chart for more information.

W482CAD – 2K Wi-Fi Camera : Installation

This article provides instructions to install your Lorex 2K Wi-Fi camera with Smart Deterrence (W482CAD).

.

What is included in the box?

The above contents are based on one camera.

.

How to connect with Lorex App

3.Open the Lorex App app and create an account or login with your credentials.

4.Tap  icon to add a new device, then follow the in-app instructions to complete the device setup.

For full instructions on Lorex App setup, see Connecting with Lorex App.

.

How to mount 2K Wi-Fi Camera to the wall

.

How to mount 2K Wi-Fi Camera to the ceiling

Wi-Fi Security Cameras – How to Read a MicroSD card

To view the contents of a MicroSD card on a laptop or computer, follow these steps:

a. Select the day to play back:

b. Click on the available folder:

c. Within the folder, click either the day folder (Video files) or the jpg folder (Snapshots):

d. Click to select a video time from 00 – 23 hours:

6.Click the MP4 video file to view the video. 

Wireless Home Monitor: Audio not working

If the audio is not working on your Wireless Home Monitor:

• Ensure that the protective film is removed from the camera lens.

• Ensure that the monitor volume is not muted. A mute icon () will be visible on the screen if the volume has been muted.

• Turn the monitor volume up using the volume buttons on the side of the unit. Location will vary by model. For exact location of volume buttons for your model, refer to your user manual. Click here for downloads and documentation for your product.

• The camera must be in Full Screen mode for audio. Tap the Channel Select icon () to switch between channels in Full Screen mode. Audio is disabled in Quad mode.

If audio is not working after increasing the volume and viewing in Full Screen mode, restore the system to default settings.

To restore your monitor to default settings:

CAUTION: Restoring to default settings will erase any setting input on the monitor. Your monitor will need to be reconfigured.

1.On the monitor tap the Menu icon ().

2.Use the joystick to select Settings > Default Settings.

3.Select Yes.

.

<p>The post Lorex Wireless Cameras and Monitors guide 2024 first appeared on NVR IPCAMERA SECURITY.</p>

How to connect a LaView Saturn Series IP Camera to a Non-Saturn Series NVR

5a. If you are connecting the camera to the NVR PoE port, set up the Target IP to 192.168.254.xxx (xxx being a random number from 2-254), and Gateway to  192.168.254.1, Subnet Mask 255.255.255.0. Then unplug the camera from the PoE switch or Router and connect it to the NVR using Cat5e cable.

5b. If you are connecting the camera via LAN, use DHCP or set up the IP address to your network range. For example: Target IP 192.168.0.217, Subnet 255.255.255.0, Gateway 192.168.0.1

6. Go the NVR Menu => Camera => Camera.

7. Click on the channel which the camera is connected to (ie if the camera is connected to port 3 on the back of the NVR, click on channel 3). If you are connecting the camera via LAN, Click on any unused channel.

8. Change ‘Plug and Play’ to ‘Manual’ and enter the camera IP address (192.168.254.xxx or 192.168.0.217 as in previous example)

9. Change protocol to ONVIF and Management port is 80

10. Enter user name and password you set up when you activated the camera in step 3.

LaView NVR Setup and User Guide

Read Also : LongPlus Camera User Guide

How to reset LaView Saturn IP Camera

3. Press and hold the reset button for at least 5 seconds until the camera restarts, and then the camera will be restored to factory default settings.

What features are LaView Saturn Series Camera compatible with LaView (LV-N95, LV-N96, LV-N98, LV-N99) Series NVR?

LaView Saturn Series IP Cameras have many great features designed to work with LaView Saturn Series NVR. If you already have a LaView NVR and wish to add a LaView Saturn IP Camera, you can do so using this instruction. However, we recommend using LaView Saturn Series IP Cameras with a LaView Saturn Series NVR for best performance.

The following features of LaView Saturn IP Camera are compatible with LaView Series NVR:

The following features may NOT be compatible

What should I do if I connect a LaView Saturn Camera to LV-N96, LV-N95, LV-N98 series NVR but only get 720P maximum resolution in main stream?

If you only get 720p in mainstream, it means the IP camera is set to H.265. Please use the following instruction to switch the camera to H.264 compression.

The system worked seamlessly until last week when it suddenly shut off and now won’t come back on

Would suggestion you follow the instruction below for troubleshooting,

1.Please ensure the cameras are connected, would suggest you to connect them directly to the PoE ports at the back of the system.

2.At the day time, try to cover the camera lens with your hands to see if there is a IR red light on the problematic cameras. And please also check if the camera goes hot when it is connected.

3.The camera appears not to get powe if there is no light and heat. We will need to check if it is the camera/port/cable issue.

1.At first, please switch the problematic camera to the workable PoE ports to test. You can also go to your PoE Configuration setting to check the power.

2.If it still doesn’t work with another port, please exchange the cable to check again. If possible, you can also add the camera to another system to confirm the problem.

Please contact our support team for further support if it does not help.

NVR is showing offline on Platform Access menu

In this case, please check the connection between the router and the NVR. Unplug and plug the ethernet cable to make sure the connection is solid. 

Then go to the NVR system, enable ‘DHCP’, “Obtain DNS Server Address” and ‘Platform Access’, disable  ‘DDNS’ and check if the status of the NVR changes from “Offline” to “Online”. Please see the pictures attached as a reference.

If it doesn’t work, please try to reboot the system to see if the issue can be resolved.

How to add Wi-Fi Cam (One PT ) to your NVR

1. Make sure One PT camera and the NVR are well connected to the same LAN. 

2. Enter the camera management menu of NVR, select an unoccupied channel, and click the “Edit” icon to add the camera manually.

3. Make sure the adding method is manual, select the ONVIF protocol, enter the correct IPv4 Address and password of the camera. 

 (Please click the link below, download the IP Portal software to your PC/laptop. Then open it to locate the IP Address and the management port of your camera.)

 http://dl.ltsecurityinc.com/software/Platinum%20IP%20Portal.zip

(Kindly note that the One PT Cam password is the same as the verification code shown on the silver sticker at the bottom of the camera.)

4. Click ‘Ok’ to save the settings and then you will be able to view the One PT camera on

your NVR.

Password Reset via XML files

Please find a 12V power adapter to power up your camera. And directly connect this camera to the router with an Ethernet cable if you need to reset the password via XML files.

Please power on the device (NVR/DVR/cameras) and connect it to the router via an ethernet cable first.

Then find the attachment and follow the instructions to export the XML file and send it to us. We will help to generate a key file and send it back to you to reset the password.

Kindly pay attention to the following when you export the file.

1. BOTH THE EXPORTED AND IMPORTED XML FILE IS VALID FOR ONLY 24 HOURS.

2. MAKE SURE THE DEVICE STAYS POWER ON AND ONLINE AFTER EXPORTING THE FILE.

If you have any questions about the steps, feel free to contact us for further assistance

Password Reset by Secure Code

Please refer to the steps as per below to reset the password. 

1. Click on the Menu button on the top left.

2. Click two times(2X) on the bottom left. Use the left button on the mouse for this.

(If you have a pattern click “Forgot My Pattern” on the bottom left of that screen to get to the login screen)

3. Send us the screenshot of the Serial No. and the date shown on monitor screen for a secure code.

​ 

4. Create and confirm the new password, must be 8-16 characters only.

Please refer to the attachments or simply click the link below to see the steps for a password reset.

https://support.laviewsecurity.com/hc/en-us/articles/115013149627-I-forgot-the-password-for-my-system-how-do-I-reset-it-

If you need further support with the steps, please reply to this email and we will be glad to assist you further.

Password Reset by Secure Code

Please refer to the steps as per below to reset the password. 

1. Click on the Menu button on the top left.

2. Click two times(2X) on the bottom left. Use the left button on the mouse for this.

(If you have a pattern click “Forgot My Pattern” on the bottom left of that screen to get to the login screen)

3. Send us the screenshot of the Serial No. and the date shown on monitor screen for a secure code.

​ 

4. Create and confirm the new password, must be 8-16 characters only.

Please refer to the attachments or simply click the link below to see the steps for a password reset.

https://support.laviewsecurity.com/hc/en-us/articles/115013149627-I-forgot-the-password-for-my-system-how-do-I-reset-it-

If you need further support with the steps, please reply to this email and we will be glad to assist you further.

Push Notification

If you would like to receive push notifications on your phone, please

Setup Email Notification

Please refer to the instructions to set up the email notifications. Here I will take the Outlook account as an example. (Sorry that Gmail is not supported anymore, please use other email addresses to set it up.)

First, please go to the Outlook mailbox settings and enable POP option.

Secondly, please go to your camera management settings -> tap into ‘Settings’ -> find ‘Linakge Action’ to enable ‘Send Email’ for each of your camera.

Thirdly, please go to your system menu -> find ‘Configuration’ -> find ‘Network’ -> click the ‘Email’ option and enter the email information:

Set up DDNS

You may follow the steps below to enable the DDNS feature,

1.Log in to http://laviewddns.com/ and set up an account

2.In the NVR interface, enter the correct account and setting in DDNS menu

3.In the router menu, assign Port 80, Port 8000 and Port 8554 to the IP address of the system

4.Go to www.canyouseeme.org to ensure the ports are opened

Feel free to email the LaView Suppor Team if you have further questions.

Set up PC viewing by PT Cloud

If you need to remotely view your system when you are not under the same Wi-Fi, please try to follow the steps below to set up the P2P connection.

Before adding your system to the PC software, please make sure your system is connected to the router(network) and is showing ‘Online’ status. Please go to your system menu -> Configuration -> Network -> PT Cloud/Platform Access to double-check your system’s online status.

Here I will take my NVMS V3 as an example.

1. Go to NVMS V3, go to ‘Maintenance and Management.

2. Click ‘Add’ here.

3. Choose ‘PT COULD’ here.

4. Log in to the LaView Connect app. Go to the ‘More’-> ‘Account Management’. Note down the ‘Username'(which belongs to your LaView P2P account) and ‘Country/Region’ information.

5. Get back the Client Software.

6. After logging in to the PT cloud account, please tap ‘Online’ and search for and choose the online device you would like to add.

7. Input the verification code set in ‘Platform Access’ in NVR and tap the “Add” icon.

. 

8. Then you are good to go now.

9. Go to ‘Main View’ on the Client Software, you are also required to input the same verification code to watch the cameras. Please input the one as #7.

Hope the above works and let the support team know with any concerns.

Set up PC viewing by IP address

Please download the PC software NVMS V3 or NVMS 7000 on your laptop to set up PC viewing. Kindly find the tools at this link: http://www.ltsecurityinc.com/downloads

Here are more instructions about the NVMS V3.

In the example, NVMS V3 will automatically detect the online device so we are adding the device with its IP address. In this way, the system and the computer will be requested to connect to the same local network so that the software can auto-detect the online system.

1. Please go to ‘Device Management.

2. Please go to ‘Online device’ and your system will be found automatically.

3. Please choose your system from the online device and click on ‘Add’.

​4. Please enter the admin name and the admin password of your system in the box popping out.

5. Your system should be added and please go to ‘Main View’ on the home page.

Please feel free to contact our support team if you need further help.

No video on monitor

Will need to confirm the resolution of the camera first. Kindly note that the resolution of the monitor should be higher than the camera’s. Otherwise, the monitor will go black. Please get in touch with our LaView Support Team and provide the model number of your camera as well as your system if you do not know the system resolution.

If the monitor and system work fine before but quit working suddenly, please change the HDMI/VGA cable to check this issue.

If you have another monitor, please also exchange it to see if it can work. If necessary, you can also try to access your system on your computer to double-check.

As for PC viewing, please download the PC software NVMS V3 or NVMS 7000 to your computer/laptop to get access. (Kindly find them from this link: http://www.ltsecurityinc.com/downloads) NVMS V3 tool is the latest version. NVMS 7000 can support the Mac system. 

Please contact our support team if the troubleshooting does not work.

How do I connect my NVR to my Phone?

Please follow these steps to setup your mobile device. You can watch the YouTube videos and follow along or follow the instructions bellow.

IPhone:

https://www.youtube.com/watch?v=zshaTac0ka8

Android:

https://www.youtube.com/watch?v=G1DtkrYLIas

LaView NET app:

*If using 4G/LTE with bad signal, you may not obtain a picture. Attempt using a strong signal.

What is an NVR?

An NVR, or “network video recorder” is a central unit that processes, records, and manages footage recorded by your surveillance cameras. An NVR recorder allows you to review and save footage, set up a recording schedule, and manage your surveillance.

Are Your Surveillance Camera Systems Hard to Set Up?

No. We have a full library of helpful videos and/or step-by-step directions for the components you purchase. Find the best surveillance camera system here, and your DIY experience will be smoother and easier than you can imagine.

Are There Any Front Door Peephole Cameras with Remote Viewing on My Cell Phone?

Definitely. We offer a front door peephole camera with remote viewing to any mobile device, fully-customizable motion detection, IR night vision, and full HD resolution.

What are the Advantages of Installing a Wifi Security Camera System?

A wifi security camera system is significantly easier to install than a traditional system, because there is no need to run special wires to each wifi camera. This not only helps the day of installation, but also allows clients to position cameras in places they might not otherwise be able to place them.

I tried to change the name of my camera, but I’m getting “Camera Does not support this function”.

It is possible that there are no cameras connected to that specific channel or the camera has lost connectivity. If you are using a third-party camera it is possible the ONVIF protocol supported by camera is outdated which does not support OSD configuration.

Is it possible to connect a third-party camera to a LaView NVR, or a LaView Camera to a third-party NVR?

Yes, if the third-party devices support the ONVIF protocol and you are using the correct setup for the specific camera.

I’m having issues connecting my NVR to my phone

Possible Fixes:

1.Please go to Menu-Configuration-Network and under the General tab make sure enable DHCP is selected, if it is not enabled then select enable and apply. If you had to enable it, restart the NVR and try the P2P setup again.

2.If you are still having issues, make sure DDNS is NOT enabled(unchecked). If DDNS is checked, uncheck it and apply then go back to Platform Access and disable P2P and apply. Once both are disabled, do a power cycle and reboot the unit. After the unit restarts enable P2P again, and do another power cycle.

3.Go to Extranet Access, Platform Access or DDNS and make sure LaView P2P is selected then apply, also make sure “Enable Stream Encryption” is disabled.

4. If none of these work, then it could be a network issue. Try to restart your modem/router by unplugging it for about 45 seconds. Plug it back in and restart the NVR, then try to reconnect your system to the P2P account.

How Do I find my system’s IP address?

To find your system’s IP address go to Main Menu>Maintenance>System Info>Network. The IPv4 Address at the top is your local IP. If your IP address is 0.0.0.0 or 192.0.0.64, this means your system is offline. There are a few causes from this, but usually, it’s a bad ethernet cable or the cable is not plugged in properly to either the DVR or Router. If those are checked to be correct, try restarting your router by unplugging it for a minute and restarting the DVR.

Can I Access a Feed from My Wifi Camera on My Cell Phone?

Yes. View your recordings or live footage anytime, anywhere! You can even and receive mobile push notifications. Stay connected at all times to your wifi camera system by simply downloading the free LaView Connect app, and enjoy your new window into your home.

Which Surveillance Camera Resolution is Best for Me?

The higher the resolution the more details you can capture in your footage. As this graphic shows, there can be noteworthy differences between a 1080p camera system, a 4MP camera security system, and a 4k security camera system. The only disadvantage to higher resolution cameras is that they consume more memory. High resolution cameras function best with motions detection cameras or larger hard drives. Many clients mix and match cameras for different applications. Feel free to call us at 626-898-4988 to discuss the best options for your specific situation.

.

<p>The post LaView NVR Setup and User Guide first appeared on NVR IPCAMERA SECURITY.</p>

The following Swann Security cameras can only be viewed and accessed via the Swann Security app from a mobile device.

They cannot be added to Swann security system recorders, such as DVRs, NVRs, and NVWs. These recorders are compatible with specific system camera models.

Can a SWIFI camera work without Internet?

Internet is required as the SWIFI cameras communicate to the P2P server using the Internet to stream to the Swann Security app and upload recordings to the cloud.

Compatible Routers

Any of the following routers are compatible provided they have a 2.4 GHz frequency:

For more information, see What router WiFi frequency band is my SWIFI camera compatible with: 2.4GHz VS 5GHz Frequency?

Compatible Wi-Fi extender or repeaters

It is possible for the SWIFI camera to pair to the router via WiFi extender if the extender is compatible and setup correctly to the router. Troubleshooting and configuration of your extender’s settings have to be performed by your router manufacturer support team, Internet Service Provider or your IT department. See this article: How to boost your WiFi signal and extend WiFi range.

Tip: Try to pair the camera to the router first to check whether its internal network adapter is working. If it works via router but not extender, then there’s a chance the extender is not compatible.

Swann Wi-Fi camera FAQs

Read More : Swann Security Troubleshooting All Devices

Not Compatible / Not Recommended

We do not recommend SWIFI cameras to be connected to the following devices because they cannot provide the necessary network configuration information to the camera to allow it to join the network automatically unless your network device is configured. Troubleshooting and configuration of your device’s settings have to be performed by your router manufacturer support team, Internet Service Provider or your IT department.

Can I view my SWIFI camera on a TV / computer or record to a DVR / NVR?

The cameras above are hub-free. A hub is a base station or recording/storage device that connects via the Internet to the cameras. In contrast, a hub-free camera operates on Wi-Fi exclusively without requiring any additional hardware to store footage. 

A hub-free (standalone) Wi-Fi camera is only capable of:

These features make a hub-free Wi-Fi camera suitable for users who prefer a wireless setup, easier DIY installation, less hardware, and less footage to check in low-traffic areas of view. 

Accessing live view, recordings, and other settings are covered in the manuals below for your device: 

How do I tell whether my router’s WiFi signal is 2.4GHz or 5GHz for pairing a SWIFI camera?

This is one of the most common reasons why a connection will fail while trying to pair a SWIFI camera to your Swann Security account. If you try to pair a SWIFI camera to the incorrect frequency or SSID name, the error that appears on the app can be one of the following:

Via Mobile Device Settings

One way to tell if the phone is connected to the correct frequency of the router is by checking the name of the SSID (the default name of your router’s WiFi hotspot): 

In the example above, the router has multiple SSIDs. An SSID that has “_2.4GHz,” “24G,” “2.4,” or “24” appended at the end is most likely a 2.4GHz signal. This is the network your phone needs to be connected to before you start pairing a SWIFI camera. 

To avoid connecting to a 5GHz SSID, see How to forget 5GHz connection for pairing a SWIFI camera.

Via Router GUI

If you see two or more Wi-Fi network names that belong to you without 24 or 5, then one may be a 5 GHz band. To identify which name uses 2.4 GHz or 5 GHz, login to your router’s settings. 

For assistance with accessing or navigating your router, contact the manufacturer of your router or your Internet Service Provider if you do not know. Swann Tech Support can only assist in pairing IF your router has a 2.4GHz signal and if you already know the correct WiFi credentials of your router.

How to change the time zone of my SWIFI camera in the Swann Security app?

The error “Device Timezone Out of Sync” appears if your camera’s time zone is different from your phone app’s time zone. 

If your camera is in a different location (with different time zone) than your mobile device, you can ignore hit Cancel. 

If the date and time displayed on the camera’s Live View is incorrect, do the following: 

Repeat each step for each camera device paired to your Swann Security account.

How to create Guest account on a WHD-PTCAM using SwannView Link software?

Installing SwannView Link

Adding the camera

Since the computer is on the same router or modem already, when you open SwannView Link the camera will be auto-detected, but the password will not be entered yet. You will see the error message below. Just click on OK.

How to forget 5GHz connection for pairing a SWIFI camera

Some mobile devices have a tendency to switch between hotspots or SSID automatically. This can disrupt the pairing process when setting up your SWIFI camera to your mobile device. 

To avoid connecting to a 5GHz signal or the wrong hotspot during pairing, forget the 5GHz connection: 

Note: If you see a WiFi name that ends with _ext, it is most likely a WiFi extender.

How to hard reset Floodlight Security Camera (SWIFI-FLOCAM2 / SWWHD-FLOCAM)

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Locate the Reset button (see below figure) on the SWIFI-FLOCAM2 / SWWHD-FLOCAM. It is behind the camera module covered by a rubber flap.

2.Press and hold the Reset button (for 20 seconds).

3.When the blue LED indicator on the camera turns off, release the Reset button.

4.The camera will start the factory reset process which can take up to 2 minutes.

5.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue).

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to hard reset SWIFI-2KOCAM / SWIFI-SPOTCAM / SWWHD-OUTCAM

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Locate the Reset button (see below figure) on the twin cable of the SWIFI-2KOCAM / SWIFI-SPOTCAM / SWWHD-OUTCAM.

2.Press and hold the Reset button (for 20 seconds).

3.When the blue LED indicator on the camera turns off, release the Reset button.

4.The camera will start the factory reset process which can take up to 2 minutes.

5.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue).

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to hard reset SWIFI-BUDDY

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Ensure the camera has been fully charged for at least 4 hours prior.

2.Locate the SET button and RST pinhole (see below figure) on the back of the camera.

3.Press and hold the SET and RST button (pin required).

4.After 2 seconds, release RST button.

5.Once blue LED turns off (or after 15 seconds), release SET button.

6.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue) and you will hear it say “Ready for pairing”.

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to hard reset SWIFI-CORECAM / SWIFI-COREPRO

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Ensure the camera has been fully charged for at least 4 hours prior.

2.Locate the Reset button (see below figure) on the camera.

3.Press and hold the Reset button (for about10 seconds).

4.Once the LED indicator on the camera turns off, release the Reset button.

5.The camera will start the factory reset process which can take up to 2 minutes.

6.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue).

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to hard reset SWIFI-PTCAM2 

How to hard reset SWIFI-XTRCAM

How to set SWIFI-MOTION / SWIFI-WDOOR / SWIFI-LEAK / SWIFI-ISIREN to pairing mode

Setting the sensor or siren to pairing mode will:

Note: If the sensor or siren is paired to your account and the Wi-Fi details did not change, it will connect back to the same network once pairing mode times out after 3 minutes.

Why does my WiFi camera stop recording motion after a minute?

Wireless standalone cameras can only record by PIR/motion. Where the camera is mounted can have an impact on how effective movement is picked up and recorded. 

Reasons:

 .

Fix: Reposition the camera or add another camera for a different angle of view.

The ideal position of the camera is 7-8 feet high, pointing downwards at an angle to cover the area where people will be walking across the camera’s path.

Can I pair my SWIFI-BUDDY to another receiver/chime?

How do I share my WHD-PTCAM?

Sharing the WHD-PTCAM

Scan to add a camera

How many files can I store in my SwannCloud account?

As of now, the SwannCloud can let you record 15 seconds per event and it will be stored approximately 5 days. In the future, there will be some other options to be chosen with regards to this but there are no approximate date of arrival yet.

How to check the battery level of my Wi-Fi camera?

This applies to SWIFI-CAM, SWIFI-CORECAM, SWIFI-COREPRO, SWIFI-XTRCAM, SWIFI-BUDDY, SWIFI-MOTION, SWIFI-LEAK, SWIFI-WDOOR, SWIFI-SIREN.

There are 2 ways:

• Dim than normal (for sensors)

• Blinking purple (for SWIFI cameras)

Note: If the Device Status is Disconnected, the battery level shown is the last that was synced to the Swann Security server and your phone before the camera disconnected. This means the current battery level cannot be seen until the camera is recharged and reconnected to the network. 

How to delete recordings of a SWIFI camera in the Swann Security app

There are two ways to delete recordings of a standalone Wi-Fi camera that is compatible with the Swann Security app.

Delete one or few recorded clips: 

1. Go to Playback.

2.Tap on the Storage (microSD card) icon on the top beside the logo.

3.Select your device. (pause and wait for the clips to load. If there are none, it means that the camera does not have a microSD card or internal storage)

4.Tap on the trash / bin icon beside the recording with timestamp you wish to remove.

Delete all recordings (Format the internal storage)

Note: Formatting deletes all recordings from local storage or microSD card. It will not delete the recordings from the cloud. Once deleted, they cannot be recovered.

1.Go to Devices > select your device.

2.Go to Settings > System Settings.

3.Tap Format.

4.Select Confirm.

How to hard reset 4K Floodlight Camera (SWIFI-4KOCAM)

How to hard reset SWIFI-2KICAM

How to hard reset SWIFI-ALERTCAM / SWWHD-INDCAM

How to hard reset SWIFI-CAM

How to hard reset SWIFI-FOURTIFY

How to hard reset SWIFI-TRACKCM

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Locate the Reset button (see below figure) on the SWIFI-TRACKCM. 

2.Press and hold the Reset button (for 20 seconds).

3.When the blue LED indicator on the camera turns off, release the Reset button.

4.The camera will start the factory reset process which can take up to 2 minutes.

5.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue).

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to playback recordings? ( via Swann Security App)

Playback tab

Open Swann Security, login your account, tap on Playback

NOTE: As of v2.7.45 in Android, you can get a preview (like a GIF) instead of a generic icon for a recorder’s clip if you enable Show playback preview under Stream Option. 

• Go Back to see results. Tap the burger icon at the upper left.

Playback Interface

How to test Wi-Fi password for pairing SWIFI cameras

This step is useful: 

 How to forget the network in your mobile device: 

.

<p>The post Swann Wi-Fi camera FAQs first appeared on NVR IPCAMERA SECURITY.</p>

O-KAM Pro APP Download

O-KAM Pro supports Android and iPhone, you can download it from google play or app store.

Login O-KAM Pro

You need to register and login to O-KAM Pro APP to connect the camera, click Register now or email icon to register.

It is recommended to allow all permissions of the APP, otherwise you may not be able to use and connect the O-KAM Pro camera properly.

Read Next : How To SetUp JXLCAM Camera

Connect O-KAM Pro Camera To Wifi

This connection mode supports O-KAM Pro wifi camera and battery camera.

1. Connect the O-KAM Pro Camera to a power source, and if it is a battery camera, press and hold the power button to start the camera.

2. Click + , then scan the QR code on the O-KAM Pro camera, the APP will automatically enter the appropriate connection mode.

If you can’t find the QR code or can’t scan the QR code, please select Wireless camera.

3. Make sure your O-KAM Pro camera is ready to connect, the camera light is flashing or you hear the prompt “Please use the app for Wi-Fi configuration”.

Note: If the light is not blinking or there is no prompt tone, please reset the camera.

Then click ‘I heard the prompt tone or see the indicator light flashing’, go to the next step.

4. Enter your wifi password, then click Next.

Please choose 2.4G wifi, some O-KAM Pro cameras only support 2.4G wifi.

.

See also  O-KAM Pro Camera FAQ and Troubleshooting

.

5. Make sure your wifi is 2.4g and the wifi password is correct, then click Confirm. Give the displayed QR code to the camera to scan.

Place the QR code about 15-30 Inch in front of the camera to scan, and complete the scan after hearing the “beep” sound.

After the connection is successful, it will automatically jump to the next step.

After successful connection, you can test the wifi signal strength, or later in the test, please put the O-KAM Pro camera in the location with strong wifi signal.

The app will prompt you to subscribe, it is recommended to cancel, if you need cloud storage, make sure the O-KAM Pro camera can work properly before subscribing.

AP Mode Connecting O-KAM Pro Camera

If the QR code connection fails or the QR code cannot be scanned, you can try to connect the O-KAM Pro camera using AP mode.

1. Go to your mobile phone’s wifi list to connect to the hotspot wifi of the O-KAM Pro camera, return to the O-KAM Pro APP after the connection is successful, and then the app will auto add the camera.

Below is the name of the O-KAM Pro camera’s hotspot wifi:

2. Go to Settings, select Device Settings, and then click Wi-Fi network.

3. Select your wifi, then enter your wifi password, click Confirm and wait for O-KAM Pro camera to connect to your wifi.

Share O-KAM Pro Camera

Once you have connected the O-KAM Pro camera, if you want your family or friends to use the camera as well, you need to share the camera with your friends via the Share function.

1. Go to the Share screen, then send the QR code to your friend.

Permission Settings:

.

See also  O-KAM Pro Camera FAQ and Troubleshooting

.

2. Have the invitee download the O-KAM Pro APP and register and login, then click + scan the QR code to add a camera.

Connecting O-KAM Pro Camera without a router

If you want to use O-KAM Pro camera without internet or router, you can connect to the included hotspot wifi to use the camera.

This mode only supports close range use.

1. Go to your mobile phone’s wifi list to connect to the camera’s hotspot wifi, after connecting, return to O-KAM Pro, the app will auto add the camera, then you can start to use it.

Below is the name of the O-KAM Pro camera’s hotspot wifi:

Function setup – Wired O-KAM Pro Cameras

The functions of different types of O-KAM Pro cameras differ slightly, so please check your camera type.

If your camcorder needs to be connected to the power supply at all times to work, then it is a wired O-KAM Pro camcorder type, please check the function setting instructions below.

Recording Setup – Wired O-KAM Pro Cameras

O-KAM Pro camera supports cloud storage and memory card recording, cloud storage requires subscription, the following memory card recording settings.

You need to insert the memory card to record, the recording will be saved in the memory card, after inserting the memory card, the camera will sound a voice prompt.

The default is to start 24 hours recording, you can change the recording mode in TF Record Settings.

O-KAM Pro camera supports the following recording modes:

If the memory card shows abnormality, please try to format the memory card and reboot the camcorder.

.

See also  O-KAM Pro Camera FAQ and Troubleshooting

.

View Recordings – Wired O-KAM Pro Cameras

In the live video interface, click TF Card in the lower right corner to view the video saved in the memory card.

Motion Detection Setup

Activate the Motion Detection function in the Monitoring Function, O-KAM Pro cameras support Motion Detection and Human Detection.

Motion Detection

When the camera detects an object moving, it will send an alarm notification to your mobile phone.

This mode may have a high false alarm rate, if you need to detect only suspicious people, we recommend you to choose Human Detection.

Human Detection

The camera will send alarm notifications to your mobile phone only when it detects humanoid objects.

Activity Zone Setup

Setting the detection area allows the camera to detect a specific location, reducing the chance of false alarms.

Smear the area you don’t need.

Detection schedule

Customize the schedule of Motion detection, reduce false alarms. The camera automatically monitors for you during the scheduled time.

Alarm flashing light

After the alarm flashing light is turned on, the camera will automatically flash when motion detection is triggered.

Camera Siren

When Alarm sound switch is turned on, the camera will emit alarm sound when motion detection is triggered, you can choose alarm sound or record your own sound.

Enter Notification Settings, select Camera Siren and then turn on the Alarm sound switch.

Email notification

An email will be sent to you when a motion is detected.

Click Add an email , then enter the email address you want to receive alarm notification and finish the setting.

Auto Tracking

When Person tracking is activated, the camera will Auto Track people’s movements and monitor all activities. It will automatically switch to and focus on the person when they enter the camera’s field of vision.

This feature is only supported by O-KAM Pro cameras that support PTZ.

Human frame

People are automatically framed in the live video Help you filter out motions of other objects and quickly follow the person’s movement.

Night vision setup

O-KAM Pro camera defaults to black and white night vision mode, you can change the night vision mode in Device Settings, Night Vision.

Only cameras with dual light sources support this feature.

Reset O-KAM Pro Camera

Press and hold the O-KAM Pro camera reset button for 5 seconds to reset the camera.

O-KAM Pro Camera FAQ and Troubleshooting

You can find here how to fix O-KAM Pro camera can’t connect to wifi, offline and not working problems.

Why is my O-KAM Pro Camera offline?

O-KAM Pro camera is offline, it means the camera can’t connect to the network properly, please follow the steps below to fix the offline problem:

Is the router working properly?
Connect your mobile phone to the router Wi-Fi, switch off the mobile data, can you access the internet normally? If it is not normal, try to restart the router.

Whether the WiF strength is full or not
Put the mobile phone to the camera installation location, detect whether the Wi-Fi signal is full? If the signal is weak, it is recommended to adjust the distance from the router to the camera.

Whether the O-KAM Pro camera is normal
If a memory card is inserted into the O-KAM Pro camera, power off the camera and remove the memory card, then check if the camera works properly.

Replace the power supply with another one.

If none of the above solves the offline problem, try resetting the camera and reconnecting it.

Why does O-KAM Pro camera keep showing that it is connecting?

.

You can also try:

If it’s a 4G O-KAM Pro camera, please detect if the SIM card’s is in arrears.

.

<p>The post How To Setup O-KAM Pro camera first appeared on NVR IPCAMERA SECURITY.</p>

How To Upgrade Firmware on a QCAM NVR.

Any QCAM NVR should always be operating on the latest firmware version available.

If you are experiencing intermittent connectivity to the internet, general bugginess or difficulty using any feature, you must make sure there is no available firmware update which would indicate you are not on the latest version.

There are 2 ways to check for your NVR firmware version:
1. On the NVR’s built-in interface, from the Main Menu, navigate to System(in the Info row)->Version.

2. On the web interface, log in, then click the “i” icon in the top right corner and you will land on the Version page.

The NVR cannot be expected to work as advertised unless it is up to date.

Please always make sure you have the latest version before trying any other troubleshooting steps or contacting support.

There are 2 methods to update the firmware on your NVR: directly on the NVR or through the web interface.

Read Next : ,

1. TKH Security Firmware Software Guide
2. TIGERSECU NVR XVR Firmware Upgrading Instruction
3. UNV NVR Cloud Upgrading Guide

Method 1: DVR Interface

The safest way to upgrade the NVR is by doing it directly on the device.

First download the most recent firmware from http://www.amcrest.com/firmware-subscribe.

Now copy the firmware onto a flash drive.

Note: The flash drive must be formatted to FAT32 or exFAT. But do not worry, most flash drives are formatted to this by default.

Insert the flash drive into the USB port on the NVR and a window will appear.

Select the System Upgrade option. You may be required to login. Be sure to use an administrator account.

The System Upgrade window will now be shown. Click Start.

Select the firmware file that you downloaded and click Start. A progress bar will be shown at the bottom of the window. Once the upgrade has finished the NVR might restart on its own.

Note: Do not turn off the NVR during the upgrade process or it can damage the NVR and make it inoperable. 

Method 2: Web Interface

First download the most recent firmware from http://www.amcrest.com/firmware-subscribe

Next login to the NVR’s web interface. Click the setup gear icon in the top right. Then click System on the left panel, then Upgrade below it.

Click the Browse button and select the firmware file you downloaded.

Click the Upgrade button and the upgrade process will begin. A progress bar will appear showing you the progress of the upgrade. Once the upgrade has finished the NVR might Restart on its own.

Note: Do not turn off the NVR during the upgrade process or it can damage the NVR and make it inoperable.

After upgrading the firmware, it is a good idea to reinstall the plugins. If this is not done automatically, or if you have issues with the web interface, check out this article: Removing Old Plugins

Important Safeguards and Warnings

Important Safeguards and Warnings

1．Electrical Safety

All installation and operation should conform to your local electrical safety codes.

The product must be grounded to reduce the risk of electric shock.

We assume no liability or responsibility for any fires or electrical shock caused by improper handling or installation.

2．Transportation Security

Heavy stress, violent vibrations, and excess moisture should not occur during transportation, storage, and installation of the device.

3．Installation

Handle the device with care. Keep the device right side up.

Do not apply power to the NVR before completing installation.

Do not place objects on top of the NVR.

4．Repair Professionals

All the examination and repair work should be done by qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or user-attempted repair.

5．Environment

The NVR should be installed and kept in a cool, dry place away from direct sunlight, flammable materials, explosive substances, etc.

This product should be transported, stored, and used only in the specified environments as stated above.

<p>The post QCAM NVR Setup and User Guide first appeared on NVR IPCAMERA SECURITY.</p>

How To SetUp JXLCAM Camera (Ultimate Manual)

This article describes in detail how to use JXLCAM camera, including how to connect JXLCAM camera, function settings, etc.
It is suitable for all JXLCAM cameras, such as mini cameras, bulb cameras, indoor and outdoor cameras, etc.

Start the JXLCAM camera

Press the power button to start the JXLCAM camera. After starting the machine, the blue indicator light flashes continuously and quickly, and the camera enters the state to be connected.

Note: If the blue indicator is slow flashing/always on or cannot be connected, long press the reset button for 5 seconds to reset.

Install JXLCAM APP

Download and install JXLCAM APP, during installation, you need to open all permissions of the APP, otherwise the APP will not work properly.

Connect the JXLCAM camera to the phone

Read Next :

1. XMEYE NVR Installation Guide
2. XMARTO NVR WiFi PTZ Camera System FAQ
3. How to use VPN on Milesight Network Camera

Local mode

When there is no WiFi in the environment, AP mode can be used for connection. The effective distance of this mode is no more than 10M.which can realize localized video viewing.

Open your phone’s WiFi list and connect to B/xCCQ……. After success, open the APP page and click AP as shown below to watch the video.

Remote mode

1. First, confirm that there is available WIFI signal near the device, turn the device on, the blue indicator light flashes quickly, and the device enters the state to be connected. (Note: only support 2.4G band WIFI signal)
2. Unable to connect successfully when power is low.
3. When connecting to the network, place the device as close to the router as possible. If the nearby available WiFi signal is weak, the connection cannot be successful or the screen will be closed after successful connection.
4. open the APP JXLCAM and follow the steps below

1. Click ‘+’

2. Click “AP add Camera”

3. Click “…” to connect to the local 2.4G WIFI band, enter the password. and then go to the next step.

4. Click”… “to connect to the camera WIFI hotspot and add the camera

5. Click”Cancel”

6. Waiting for the connection.

7. Click”Next”

8. You can change the name or not, and then click “Next”

9. Check out the video preview on the home page

JXLCAM APP interface description

JXLCAM FOR PC

JXLCAM App is developed by the JXL.Inc. JXLCAM is the app for security cameras. Now guys if you want to use JXLCAM on the PC so, You can follow some easy steps and it will be easily installed on your laptop PC

Install JXLCAM on PC

Now Here we will going to install JXLCAM on PC, for that you have to install Bluestacks on your PC. Bluestacks is and professional android emulator to run android apps on the PC or MAC. After installing bluestacks in your PC, you can easily run any of Android apps on your PC including JXLCAM APK

So, first install Bluestacks and then you install JXLCAM in the Bluestacks emulator.

How to install the JXLCAM app on Windows and Mac

Go to the below link and download JXLCAM for PC or MAC and before that make sure to check the below minimum system requirements for installing Bluestacks on your PC to use JXLCAM.

Minimum System Requirements:

• OS: Microsoft Windows 7 and above.
• Processor: Intel or AMD Processor.
• RAM: Your PC must have at least 2GB of RAM. (Note that having 2GB or more disk space is not a substitute forRAM)
• HDD: 5GB Free Disk Space.
• You must be an Administrator on your PC.
• Up to date graphics drivers from Microsoft or the chipset vendor.

Download Bluestacks

After you install bluestacks, then you can install JXLCAM APK in Bluestacks. so follow the few steps given below to download and install JXLCAM on your MAC or PC using Bluestacks.

1. Open the browser or google play to install the application
2. Open your browser and type in [ https://jxlcam.com ] and download JXLCAM APK
3. After JXLCAM download is complete.
4. Just open the .apk file and install it as a normal .apk file
5. Now, if you go to the bluestacks home screen, you will see the JXLCAM APK installed
6. Just open the JXLCAM app and use it
7. Now you can enjoy JXLCAM on your PC or MAC APK

FAQ

Is there any EXE or dmg software for JXLCAM?

No, to use on the computer, you can only install the APK mobile version.

JXLCAM

Jxlcam is an app that works with home surveillance camera devices

1. The monitoring of the specified device uid can be viewed only by connecting to the specified device uid
2. No matter where you are, you can view the monitoring anytime, anywhere
3. It supports capturing screen photos and recording videos and saving them locally
4. Support monitoring camera equipment and intercom with camera equipment
5. Support SD card video playback function

Android

iPhone

For PC

<p>The post How To SetUp JXLCAM Camera first appeared on NVR IPCAMERA SECURITY.</p>

UBox Features

• Support user register and binding device to user account
• Support power-saving mode and remote wakeup
• Support TF recording and cloud recording video
• Support notification with a snapshot
• Support notification with AI face recogization
• Live view H.264 720P/1080P up to 30FPS
• Dual way audio
• Remote Parameter setting
• Remote query alert and playback
• Support WiFi doorbell
• Support WiFi battery camera
• Support 4G wireless battery camera
• Support Solar WiFi/4G wireless camera
• Support Panoramic camera

How to Install UBox for PC

You need to Download BlueStacks on Windows or Mac PC first. Afterward, you have to start the installation of BlueStacks on your computer.

It is similar to any other software installation procedure on a PC. Run the setup, Allow the software to make changes in your computer, and then it will start to install.

In the second step to get UBox Download for PC, users have to enter Google Account. After the installation of BlueStacks, you will see the emulator home screen. Locate the Google PlayStore and launch it.

First-time users have to enter Google Account which is already in existence. Or, users can create a new one if unavailable.

Here the final steps arrive, now users are ready to use UBox on Laptop or desktop. Users got 2 options to accomplish the task.

1. Visit the Google Play Store > Search for the UBox App > Install it.

2. Downlaod UBox APK on PC > Drag and Drop it inside BlueStacks > Allow the emulator to install.

That’s how you can install UBox for PC.

Read Next : 

1. How to set up Geeni smart Wi-Fi camera
2. How to Install Joylite Smart Cameras

UBox Camera Common Problems

<p>The post UBox Camera complete guide UBox For PC first appeared on NVR IPCAMERA SECURITY.</p>

Safire NVR Setup Guide

Read Next :

• XMEYE NVR Installation Guide
• ClareVision NVR and Camera General Guides
• UNIARCH NVR DVR Full installation user manual

Email settings in Recorders and Cameras: Gmail and Yahoo

Let’s explain how to add these two servers to a recorder or camera, bearing in mind that it may be easier to do so with Yahoo as there are fewer steps to configure.

GMAIL

The data of this mail server are the following:

Smtp server: smtp.gmail.com

SMTP Port: 587

Enable TTL

It’s also important to enable POP and IMAP in your mail.

It is also necessary to activate the sending of emails from less secure applications, from this tab: https://www.google.com/settings/security/lesssecureapps

IMPORTANT: Do not enable two-step gmail protection

Example: brand Safire Safire with Gmail

YAHOO

Smtp server: smtp.mail.yahoo.com

SMTP Port: 587

Enable TTL

Example: X-Security brand with Yahoo

VCA (Area Intrusion Detection) configuration concepts from a SAFIRE video recorder

Threshold: Time, in seconds, that the target must remain within the detection zone to generate an alert.

Sensitivity: Inverse of the percentage of the target area entering the detection zone, relative to the total target area, to generate an alert. The formula that describes this concept is A/A+B>100-S, where A is the target area within the zone, B is the target area outside the zone and S is the sensitivity. A value of 80 will only trigger the alert when at least 20% of the target enters the area.

Percentage: Minimum area (in percentage) of the detection zone that has to be occupied to generate an alert.

Follow a guide in English for installation and configuration of VCA rules

SAFIRE How to setup …pdf

Slot for SD card in camera SF-IPSD6525UAWH-2

To find the space dedicated to the SD card, follow the hereby attached scheme:

Activate PIR detection and alarm sound on SF-IPCU202AWH-2W

With this configuration the PIR will alert our mobile device and the camera will emit an alarm sound in case of detection or event.

These two options can be managed from the camera’s own web interface.

To arm and disarm the PIR notifications, it is possible to configure it from the app (while the sound management has to be managed by web).

Installation and Configuration manual of TrueSense technology

<p>The post Safire NVR Setup Guide first appeared on NVR IPCAMERA SECURITY.</p>

• Technical review 1793 (1).docx

iViewer installation and user guide

Read Next : Default Password NVR &#8211; IPCAMERA

Question

What to do if iViewer doesn’t show some cameras of VAST? (set logical tree in VAST)

Answer

Question

When I add new substation to VIVOTEK CMS, how can I see it on iViewer at the same time?

Answer

Cannot visualize 7000 series cameras’ streaming when using codec JPEG

Question

After upgrading iViewer(iOS) to version 3.12.2, I cannot get IP7330 camera streaming.
But when using iVeiwer for Android, it works well.The following shows an iPhone using iViewer 3.12.2 to connect to IP7330.

Answer

This issue appears because iViewer(iOS)3.12.2 removed the server push mechanism but  iViewer(Android) still keeps it.
Therefore, iViewer(iOS) cannot get the 7000 series streaming when using codec JPEG but iViewer(Android) works well.In order to resolve this issue, please change the camera codec from JPEG to MPEG-4.

What ports are used for camera’s two way audio if you add a camera with public IP address to iViewer?

Question

What ports are used for camera’s two way audio if you add a camera with public IP address to iViewer?

Answer

If you would like to use a camera’s two way audio on iViewer, make sure below two ports are opened on router for the camera.

1. Sip port (Two way audio port). The default port is 5060.

2. RTP port for audio. The default port is 5558.

You can change the port value if needed.
For the SIP port, the range of port value is as below: 1025~65535.
For the RTP port for audio, the range of port value is as below: 1025~65535.

How to back up the iViewer completely when you back up your iPhone via iTunes?

Question

How to back up the iViewer completely when you back up your iPhone via iTunes?

Answer

Please enable the “Encrypt local backup” settings before backing up the files.
iViewer encrypt the camera password. If you do not enable this setting, you will not see any camera data in iViewer after reload the backup file to device.

How to add the camera into iViewer?

Answer

iViewer crashed on iOS9

QUESTION

iViewer crashed on iOS9, but iOS10 works OK, please solve the problem

ANSWER

Sorry for the inconvenience, it turns out Apple just let our team know today that they have made some changes on iOS end, so we need to modify some part on APP as well
After we modify this part, the APP would be able to work on iOS9 without problem
We have already implemnt the fix and try register the new APP on apple store, the new APP (3.7.6) is already available on 10/24

How to update VAST status in iViewer?

Question

How to update VAST status in iViewer when the substation has been disconnected or substation name has been modified?

Answer

Please follow below steps to update VAST status:
1. Slash toward left on VAST icon
2. Click update icon

3. After a while, the VAST status will be updated.
The connection status, substation name and total device number will be updated also.

What pan/tilt speed is supported?

QUESTION

What pan/tilt speed does iViewer support?

ANSWER

iViewer supports 3 speed levels for pan and tilt: -5, 0, 5.

From center circle to narrow, we divide it into 3.
What speed is using depends on how far you move from center circle to narrow, as below:
0 (Central circle) to 1/3: speed -5
1/3-2/3: speed 0
2/3-1 (narrow): speed 5

The app crashed while you try to open it on x86 CPU device

QUESTION

[VIVOCloud/iViewer][Android] The app crashed while you try to open it on x86 CPU device, e.g. ASUS model K011 tablet

ANSWER

Our APP only support ARM CPU, not fully supported by x86 CPU device.
Though x86 CPU would try to interpret ARM library, however, when it failed on doing that the APP would go crashed.
Nowadays there barely got x86 smart phone, the most common series is ASUS Zenphone, but they stop using x86 from 3rd genereation.
This is current limitation, hope we can get your understanding.

iViewer crashed after viewing Liveview page of VAST server

QUESTION

[iViewer][iOS/Android][3.10.301] iViewer crashed after viewing Liveview page of VAST server, you would see iViewer is trying to load streaming of VAST and it would suddenly crashed

ANSWER

The parser of iViewer is receiving unexpected response from VAST server.
If you run into this issue, please upgrade iViewer to version 3.10.401 or later version

Name of VAST substation changed to accessing server and no cameras

QUESTION

VAST has a substation(ND9441P 2.2.102) and the substation is online.
But the name of the substation on iViewer shows “Accessing server…” and all cameras disappear, as shown below.

ANSWER

It’s a known issue on iViewer Android 3.10.301, and it has been solved on newest official version 3.10.501
If you meet such issue, please update to newest version.

How to add or remove different camera in my favorite list on iViewer?

QUESTION

How to add or remove different camera in my favorite list on iViewer?

ANSWER

<p>The post iViewer installation and user guide first appeared on NVR IPCAMERA SECURITY.</p>

Amazing Features, Top 2 Picks, Setup Steps & Hottest FAQs

Blue Iris Cameras is a smart tool used by a lot of people to access and control their security cameras. In this complete guide, you’ll get deep insights into Blue Iris software, the recommended Blue Iris compatible cameras, step-by-step setup guides, and troubleshooting.

If you have other questions about Blue Iris supported cameras, leave them in the comment below.

Table of Contents

• Blue Iris Cameras: Features & Compatible Cameras
• Blue Iris Compatible Camera Top Picks
• Set up Blue Iris Cameras: Step-by-Step Guide
• Troubleshooting for Blue Iris Cameras
• Frequently Asked Questions about Blue Iris
• Conclusion

Load more :

• Blue Iris IP Camera Software Setup Guide
• Troubleshooting Physical Cameras in 3 steps

Blue Iris: Software Features, Compatible Cameras, and Pricing

In order to help you get as many details as possible on Blue Iris webcam security cameras, we will break down this topic into 4 parts and every part will contain the points you want to learn about.

1. Meaning

2. Compatible cameras

3. Pricing

1. What is Blue Iris software

Blue Iris, or BI for short, is a popular video security and webcam software that enables people to remotely access and control their security cameras on personal computers, iPhones, or Android smartphones.

Blue Iris has many configurable options, including remote live view, playback, PTZ control, motion detection, audio recording, E-mail alerts, and many other functions.

With Blue Iris compatible cameras, you can keep tabs on your home and business, watch your kids & pets, and monitor your valuables via this professional software.

The advantages of Blue Iris mainly include:

• You can control multiple security cameras & systems simultaneously from various brands on Blue Iris.
• As an open platform, Blue Iris welcomes all companies and organizations.
• Blue Iris captures videos in various formats, including standard MP4, AVI, advanced DVR, and Windows Media.

Keep in mind that not every security camera is completely compatible with Blue Iris, you need to check the compatibility details or ask the security camera manufacturer before making a purchase.

2. Blue Iris compatible cameras

Most security camera types in the market are compatible with Blue Iris, including webcams, analog cords, and network IP cameras.

According to the test done by the Blue Iris team, there are thousands of tested security cameras that are compliant with Blue Iris, so it’s hard to give a full list.

But there are some clues for you to know whether your camera is compatible with Blue Iris. If your camera belongs to any of the following ones, it can work with Blue Iris. If not, you can contact the camera manufacturer to find the answer.

• Any camera that supports JPEG images
• Any camera that supports MJPEG streaming
• Any camera that supports MPEG4 over RTSP streaming
• Any camera that supports ONVIF protocol

Here are several popular Blue Iris compatible camera brands:

• Reolink (except its battery security cameras, add-on cameras, E1, and Lumus)
• Amcrest
• Hikvision
• Dahua

Sometimes not all the functions of a compatible camera can be used on Blue Iris. So you need to check the details of Blue Iris compatibility from the security camera brand.

Reolink team has tested the compatibility of their cameras with Blue Iris. The result is that Reolink security cameras can “communicate” with Blue Iris in almost every way. In other words, you can make full use of Reolink cameras on Blue Iris software.

3. Blue Iris license & tech support fees

You’ll need to pay for the license and tech support when using Blue Iris software, which is licensed per PC for a lifetime.

Before purchasing the Blue Iris license, you can get a free 15-day trial. After that, you’ll need to pay for the usage of Blue Iris.

There are two versions of the Blue Iris license for you to choose from:

• The LE version only supports a single camera at a price of $34.95.
• The Full version supports multiple security cameras (up to 64 cameras), at a price of $69.95.

If you want to manage multiple security cameras at one time or plan to expand more cameras in the future, the full version would be a much more cost-saving option in the long run.

Also, you’ll need to pay for the tech support of Blue Iris. You’ll get 1-year basis support plan for free. When your basic support plan expires, you’ll need to upgrade it to an Extended Plan ($29.95/year) or a Priority Plan ($59.95/year).

Blue Iris Support Plan Details & Prices

Support Plans & Features	Basic	Extended	Priority
Current Version Updates	Yes	Yes	Yes
Major Version Upgrade Protection	—	Yes	Yes
Email Support	Yes	Yes	Yes
Prioritized Email Support	—	Yes	Yes
Highest Priority Email Support	—	—	Yes
Phone Support (Limited & By Appointment)	—	—	Yes
Remote Desktop Support (Limited & By Appointment)	—	—	Yes
Price	Free	$29.95	$59.95
Duration	1 Year	1 Year	1 Year

Note : The information in the chart above is quoted from Blue Iris official website.

For people who don’t want to pay so much for using Blue Iris software, the customized software of the security camera manufacturer (such as Reolink App) would also be a good choice.

You can use the software without any charges and get free tech support. More importantly, there is no need to worry about the compatibility of your cameras and the software at all.

Best Cameras for Blue Iris Recommendations

We pick two popular Blue Iris compatible cameras, including a PoE and a wireless type, for your reference. Both of these two security cameras are highly praised by professional tech reviewers and customers.

This camera features 4K 8MP ultra HD, enabling you to see details in the picture clearly. 5X optical zoom lets you check anything you like freely. Besides, RLC-811A can detect any person & vehicle and send instant alerts to your phone.

You can make use of almost all the functions of RLC-811A on Blue Iris software. Once you enter the IP address/port, Blue Iris can instantly pick up the camera.

This PoE camera can save you from messy hassles and bring solid security to your home. With rich features, it’s at a reasonable price. If you want a 4K PoE camera for Blue Iris, give it a try.

For those who are looking for a PTZ (pan-tilt-zoom) camera for Blue Iris, E1 Outdoor can be a great choice.

This wireless outdoor security camera is packed full of features and at a nice price. It offers you 5MP high resolution at 2560 x 1920 pixels, person/vehicle detection for accurate alerts, and color & clear night vision with 12 IR LEDs and 4 extra spotlights.

More importantly, it has the amazing PTZ function. You can view nearly everything with 355° pan & 50° tilt, and check details closely with 3X optical zoom. This camera can also track the moving person/car automatically.

This PTZ security camera is fully compatible with Blue Iris, which has a PTZ/Control dialog for you to customize settings. If you want to know more, here is a thorough guide to BI’s PTZ/Control for your reference.

Blue Iris Camera Setup: Step-by-Step Guide & Videos

Some people may have trouble adding a new security camera to Blue Iris. You can follow this step-by-step guide on adding IP cameras to Blue Iris and control your cameras like a breeze.

Here we’ll take the compatible OEM cameras as an example, and the steps apply to other types of cameras that are compatible with Blue Iris.

Step 1. Initialize the camera settings

1). Add the camera to Reolink Client. You can add it by entering UID or IP/Domain address. Also, it will show you devices in the same LAN and you can click the “+” button to add it.

2). Set up User Name (the default user name is admin) & Password. Click Login.

3). If you’re going to use ONVIF or RTSP later on Blue Iris, you need to set the port first on Reolink Client.

Click Device Settings -> Network Settings -> Advanced. Find Port Settings and click Set Up. Enable RTSP and ONVIF, and then click Save.

Step 2. Add Reolink cameras to Blue Iris.

This step is done on Blue Iris software, so you should launch Blue Iris on your PC or Mac first.

1). Click the “+” button at the top right, or right-click and select Add new camera.

2). Input the camera name and choose Network IP as the connection type. Check Enable audio and Enable motion detector in the Options menu. Click OK to continue.

3). Input the IP address, the correct User Name, and Password. Click the Find/inspect… button to search the camera in LAN.

In the current window, you are gonna need to do several setup steps:

• Set Make to Reolink and choose the corresponding model.
• Change the Discovery/.. ort into 8000. (If you ever change RTSP or ONVIF port number, you should input the current value.)
• Click OK to finish adding the camera to Blue Iris.

If the connection fails (there is a striped video signal), you can change the Make option to Generic/ONVIF and the Model will automatically change to RTSP H.264. Still, make sure the ONVIF port is 8000 (default number) or the current value if you ever changed it.

Here is a video to show you how to add Reolink cameras (exclude some cameras) to Blue Iris from the beginning to the end.

4). Configure PTZ security camera on Blue Iris.

If you use Reolink PTZ security cameras, such as RLC-823A or E1 Outdoor, you can enable the PTZ function on Blue Iris by clicking the PTZ/Control tab and checking Enable Pan/Tilt/Zoom and other controls (focus. Brightness, etc.).

Don’t forget to set Network IP. Click OK to save settings.

Bonus tip: You can follow this step-by-step guide to call PTZ IP camera preset on Blue Iris.

If you have any questions about adding Blue Iris cameras, you can leave them in the comment below.

Blue Iris Cameras Troubleshooting

Some of you, especially the beginners, may encounter various problems while using Blue Iris software. So we list the issues you care about most and offer the solutions that can help you use Blue Iris cameras better.

Blue Iris cameras recording issues

Here are some of the most typical recording issues that may happen to you when using Blue Iris.

– Issue 1. Blue Iris won’t record videos, both motion-triggered and continuous videos.
You can try the following methods.

• Upgrade your Blue Iris to the latest version.
• Make sure you’ve enabled the motion detection or 24/7 recordings on Blue Iris.
• Turn on direct-to-disc recording.

– Issue 2. Blue Iris not creating new recordings for hours? What settings do I need to fix?

If you expect each motion-triggered video recording to be stored separately, please follow the below simple steps:

On the camera properties, please click Record tab, and then uncheck Combine or cut video each.

– Issue 3. How to record 24/7 with Blue Iris?

You can make your security camera record 24/7 on Blue Iris with the following steps.

• Right-click the camera.
• On the camera properties, click Record tab.
• Select Continuous under Video.

How to set up motion detection and video recording on Blue Iris?

After you’ve added your camera to Blue Iris, you can follow the instructions below to set up motion detection.

Step 1. Click the camera icon  at the top/left of the Blue Iris window, and then click the Motion/Trigger tab.

Step 2. Check the required boxes, including Enable under Motion sensor, Object detection, Use zones and hot spot, High definition, Cancel shadows and Trigger using cameras’ digital input or motion, and then click OK.

Step 3. Click the Record tab, and then check the required boxes including Video, JPEG snapshot each & Create Alert list images when triggered, and then click OK.

Now you can get motion detection recordings with the Blue Iris.

Blue Iris requirements and setup questions

According to Blue Iris’ team, the minimum requirements for your computer are:

• A dual-core or equivalent 2 GHz processor or better
• More than 2 GB RAM
• At least Microsoft XP SP3 or newer version, such as Window 7 & 10, or a server OS
• 1 or more cameras with DirectShow drivers

If you use multiple Blue Iris security cameras, such as 12, 16, 30, or even a maximum of 64 cameras, you need a much more robust computer. Recommendations include:

• Intel core i7 with QuickSync for hardware decoding
• More than 8 GB RAM
• Microsoft Windows 8.1 or 10, 64 bit
• NVIDIA graphics adapter for efficient screen display
• 7200+ RPM drives and/or SSD drive

In order to minimize your computer CPU consumption, you may set up the video frame rate to 15-20 fps.

NVR system V.S. Blue Iris + PC, which is better?

If you only need 2 or 3 IP cameras to run 24/7, and/or happen to have an extra computer, you can opt for Blue Iris + PC option.

Your computer storage space can handle several IP cameras recording continuously.

But if you want 4 or more cameras, a dedicated NVR would be the way to go.

Typically, the cameras and NVRs from the same brands can work seamlessly. All the videos will be stored on the hard disk of the NVR for your later playback.

If the storage space of the NVR is running out, it would automatically overwrite the oldest video footage, so you don’t need to delete the videos manually.

You can check more details on NVR vs PC for security camera video storage.

Frequently Asked Questions about Blue Iris

Here are some questions often asked by Blue Iris users. Now you can find the answers quickly.

How many cameras can Blue Iris support?

As mentioned above, Blue Iris can support multiple (up to 64) cameras with the full version license.

But don’t forget that Blue Iris LE version license only supports 1 camera. So if you want to manage multiple cameras, you’d better have a full version of Blue Iris.

How to solve Blue Iris CPU usage problem?

When you use Blue Iris to control your surveillance cameras, BI’s motion detection and transcoding would consume much CPU power of your computer.

You can try the below 5 useful tips to minimize the CPU consumption caused by Blue Iris.

1. Turn on Direct-to-disc recording. It records the cam streaming without re-encoding. However, it has downsides. Blue Iris won’t be able to add its own overlays (time and camera name).

2. Turn the video frame rate down to 15-20 fps.

3. Reduce pre-event capture to 40 frames.

4. Turn down the sensitivity level of the motion-triggered setting.

5. Shorten the pre-recorded time in motion detection setting.

What if Blue Iris camera has no signal?

If you encounter security camera signal loss when using Blue Iris, you may try the below solutions to troubleshoot the issue.

• Update Blue Iris to the latest version.
• Lower the camera’s frame rate.
• Reboot your security cameras & Blue Iris software.

How to rearrange cameras on Blue Iris?

If you cannot change your security camera layout on Blue Iris, you may follow the below 2 simple steps to fix it.

1. Right click the blank space in the Blue Iris window.

2. Uncheck drag lock.

Now you can change the security camera group layout on Blue Iris.

Which cameras does Blue Iris support?

Most cameras in the market are compatible with Blue Iris, including Webcams, Network IP cameras, and others. The most popular security camera brands include Reolink, Amcrest, Hikvision, Dahua, etc.

But remember not all of the functions of the compatible cameras can be used on Blue Iris. So you’d better confirm the compatibility issues with the manufacturer.

Does Blue Iris connect to a WiFi camera?

Yes, Blue Iris works with most network IP cameras, including WiFi cameras, PoE cameras, or USB IP cameras. You need to set up the WiFi camera first with the software of the manufacturer. After you’ve initially set it up, you can add the WiFi camera to Blue Iris quite easily.

For more details on adding cameras to Blue Iris, click here >>

Conclusion

Blue Iris is one of the best professional software for security camera recording and monitoring. The best part of it is that it allows you to manage and control different models of various brands. Apart from that, the rich features of Blue Iris are another reason why so many homeowners love it.

If you have any problems with Blue Iris software or Blue Iris compatible cameras, feel free to discuss them in the comment below!

As one of the most popular and best 4K PoE cameras, RLC-811A can work seamlessly with Blue Iris software.

<p>The post Blue Iris Cameras 2022 Complete Guide first appeared on NVR IPCAMERA SECURITY.</p>