This is a user guide for CMSClient version V1.00.00.47, it’s applied to software version is equal or newer than V1.00.00.47. If you are running older version (e.g. V1.00.00.46, V1.00.00.45), please download and upgrade your existing one to the latest. It should be noted that Yoosee has no app be compatible with Windows smartphone. If you have a smartphone running Windows OS, obviously you can not use Yoosee camera. The Yoosee software team will not release App for Windows based smartphone.

What CMSClient does?

CMSClient provides users a centralized video surveillance solution. It allows users to manage multiple cameras simultaneously, users can preview, record, playback, even receive alarm alerts by using it.  Users also can change yoosee camera’s network settings (such as IP address, gateway, DNS), can shift recording video resolution from SD to HD, can modify camera’s password.

Installation of CMSClient software

The software doesn’t contain any virus, if your anti-virus software report virus warning, please check if you have downloaded the software from official website. The software requires permission to access your network/Internet, it uses RTSP stream protocol to communicate with cameras locally, and P2P protocol to communicate with Internet cameras. When installing the software, ensuring it allows to pass Windows firewall.  The software will keep communicating with remote servers intending to establish P2P connection, it doesn’t spy your video, doesn’t transmit/upload any video clips to remote servers.

Logon CMSClient Software

CMSClient software now allows users to login through three different types of account.

• Admin login: local login, don’t require users to register an account. No need to input password, click “OK” to login immediately. The software can automatically discover local cameras, but can not discover Internet cameras.
• Phone Number login: remote login with your registered yoosee account, after logon, the software will list added cameras in your account.
• Mail/user ID login: remote login with your registered yoosee account, after logon, the software will list added cameras belongs to your account.

Moreover, select either “Phone number login” or “Mail/user ID login”, the software can receive motion detection (or sensor triggered) alert to computer. When motion detection alarm occurs, the software will pop-up a new window automatically to alert users, it also can play selectable audible automatically to remind users.

How to add Yoosee Cameras?

After logon, CMSClient will automatically discover local connected cameras, click “Add all” to add them into your software. Please note the displayed p2p password and rtsp password default is “qwe123”, it’s an incorrect password, just ignore them.

Except adding automatically, users can click “+” icon on the left bottom to manually add cameras. In “Device manager” window, local connected cameras will be listed on the left column, click “>>” button can add to software which will appear in right column. Click “Manual add device”, you can add local connected cameras via entering device ID, device password, RTSP password. Click”Add shared device” to add cameras as a guest user. In pop-up windows, you should paste the shared link. To know how to get shared link, you can read this article – How to use Yoosee App’s sharing function?

How to use CMSClient software?

Once you added devices to software, you’re able to use each functions of it. Select device you want to manage, right click mouse will pop-up a menu list.

• Device property: change camera name, device password, rtsp password and group.
• Delete node: delete camera from this list/software.
• Start monitoring: start to preview real-time video (if it shows you a crying face, it means password is incorrect)
• Smooth/standard definition/high definition: before click start monitoring, you should choose default image resolution, smooth equals low resolution, standard definition equals VGA (640×480), HD equals 1280×720 or 1920×1080.
• IPC config: you’re able to tweak camera’s network settings (e.g. IP address, DNS), record video resolution (SD, or HD), password.  It only works on the premise that your camera’s password is correct. If you encounter “network timeout” “permission error” “password incorrect” error, to solve this, you need to logon software with yoosee registered account.

CMSClient Playback Function

You’re able to playback recorded video clips right from your computer. The CMSClient can only allows users to play remotely and locally recorded video clips, but also can allow you convert them to friendly .mp4 files which can be recognized and played by regular media players.

Click “Search” button on the left top, the camera can search files, click the file name to playback. Additionally, you can click folder icon to open a file to play it. All yoosee camera will record video with .av file extension. These raw files can not be recognized or played by regular media players, you can use the converter which the software has included to convert .av files to .mp4 files.

If you don’t want to install and use CMSClient software, still want to play .av files in another computer, you can read this article – How to play .264 video files from IP cameras/DVRs/NVRs?

CMSClient software is a powerful video surveillance management tool, it includes other function to provide a great flexibility. Click gear icon on the top of software, it will pop-up a “CMS config” window.

• File save path: select the folder path to store recorded video footage.
• Reserve space: allowing users to modify reserved space for video storage in your HDD.
• Record time for package: the time length to patch a video file when recording video. If the value is “60” min, the software will patch/generate a video file in every hour when software is recording on computer.
• Cycle record: turn on/off over-write function, automatically erase/overwrite HDD when space is full.
• Auto start record when monitoring: record video while watch video stream.
• Connect all of device automatically: automatically display video for all cameras/channels after logon software.
• Render mode: Directdraw, GDI
• Monitor: auto, rtsp, p2p
• Message notification: choose whether receiving message notification or not when there is a motion detection alarm.

If you logon software with registered yoosee account, the software will have “Alarm trigger” option. This open allows you to select time length of pop-up video when alarm occurs. You’re able to choose different audio files, the computer will play the audio to remind users.

<p>The post User guide for Yoosee App PC Software – CMSClient first appeared on NVR IPCAMERA SECURITY.</p>

We can talk directly on phone app for asking courier to put package to a certain place you point, and hear sound from app or TV monitor connected to NVR

We could be alerted any time a person enter your property by receiving push notification from free phone APP, and the alarm light will be triggered to drive away the suspicious objects ( Note: APP has No Monthly Fees)

High Resolution 2592 X 1944 pixel to provide your vivid and clear image no matter in day or night, and IP 67 Waterproof to withstand Changeable Weather like Snowy/Rainy Day

We can customize the surveillance area or set a line for human/vehicle, and the alarm alerts will be triggered when detecting human/vehicle crossing the line or intruding the alarm area （These function may only work with Hiseeu NVR）

Version 2020-2022 PoE System FAQs in total

.

Further support, plz email us at email love@hiseeu.com

Or contact us at +1 917 688 2228

.

Important Notes:

These FAQs are only adaptable to following Models NVR Model : H5-NVR-P-8,

Camera Model: HB215-PA, HB212-PA, HB915B-PA

Mobile Phone APP: XMEye Pro         PC Client :VMS

Hisseu PoE Camera System User Guide v1

Contents:

A:  Forget NVR Password?

B:  Add Device on PC Client Software (VMS）?

C:  How to Sign up account on Mobile APP (XMEye Pro) ?

D:  Add Device on Mobile Phone APP (XMEye Pro)?

E:  How to enable Alarm Notifications on APP XMEye Pro?

F:  Configure Offline Camera or Add a New Camera?

G:  No Video Display on TV Monitor Or Blank Screen?

H:  Why DVR/NVR can’t record or playback video?

.

Detail Solutions:

A:  Forget NVR Password?

1. Please click the mouse from the home screen, and “Logo Out–>Log Out”

2. Right click the mouse again, click “ Main Menu”–> “Forget password –> Forget answer”, you will see the “QR Code”

3. Please open your mobile APP “XMeye Pro”

（1）Click the Scan icon on the top left corner

（2）Scan the “CAPTCHA” on the TV monitor, then you will get a code from the mobile phone APP or from your email, and enter the code into “CAPTCHA”, so you will be able to reset the password on the Monitor connected to DVR

.

B: Add Device on PC Client Software (VMS）?

VMS download link:

For Windows （2023 newest version）

https://download.xm030.cn/d/MDAwMDE0OTM=

For Mac ( 2022 version)

https://download.xm030.cn/d/MDAwMDA2NDA=

1. Download PC Client “VMS” and installed

2. Login with the default User Name and Password. Click “SIGN IN”.

Default User name is: admin

Default Password is: admin

3. Navigate to “Device Manager”–>”Manual Add”

4. Login Type: Cloud ID Device Name:

Name Your Device as you like

Cloud ID : Device Serial Number. We need to go to the TV Monitor connected to the NVR , and find out the information on TV Monitor UI, then right click the mouse to navigate to the path of “Main Menu–>Advanced–>Version” to find out the information “serial number”

User Name and password: Input the user name and password that you created for the NVR , and we also need to find this from the Monitor UI.

.

5. Navigate to “Live View”, Click on the device name(serial number), then select “Open All By Sub Stream”

.

C:  How to Sign up account on Mobile APP (XMEye Pro) ?

Please follow these instructions to sign up for an account via your mobile number.

1. Click on Sign Up

2. Sign Up by email or Select Mobile Number

3. Select the correct country code +1, input your mobile number and click on “Get code”

4. A code will be sent to the mobile phone number, input the verification code and continue.

.

D:  Add Device on Mobile Phone APP (XMEye Pro)?

Steps:

–>1. Please connect the NVR/DVR box to your Router via Network Cable; (Some customers think it can support WIFI connection, while wired systems only support wired router connection, and have to be wired to router via ethernet cable)

–>2. Go to Monitor UI Interface, and Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR/DVR is online (Please skip step3),

–>3. If the cloud status shows “Probing DNS”, Please Navigate to “Main Menu > Network > Check the icon of “Enable DHCP”–>Apply;

–>Reboot the DVR by unplugging the power adapter and re-plug it, then double-check the cloud status ( only cloud status shows )

–>4. Go to your TV Monitor, navigate to “Main Menu–>Advanced–>Version”–> You will see the serial number.

The QR code contains Serial number info. We need this information after we add the device to mobile phone APP

–>5. Open the mobile APP “XMeye Pro” and register an account by your email first

–>6. Click”+” to add device–>Choose “NVR”

Device Serial Number: Click the “Scan” icon to Scan QR Code On the NVR UI Interface (Main Menu–Advanced–Version), (QR code contains username and password)

No need to input the username and password manually.

And click “OK”, and go back to the Device page on App,and you will see the device shows status:online ,

E:  How to enable Alarm Notifications on APP XMEye Pro?

1.Make the Alarm setting is already set on Monitor UI Interface

2. Please right-click mouse and navigate to “Main Menu–> Alarm–>Motion Detect/Human Detect/Face Detect–> Enable “Mobile Reported”–>click “OK”

(Default Setting is for Channel 1, Please select “All” channels.)

2.Open “XMeye Pro” mobile App, and navigate to “Event–>Device (the one you named)–>Enable “Allow Notifications”

.

F:  Configure Offline Camera or Add a New Camera?

—>1. After connect the camera to NVR via network cable, if the camera power on properly, the camera’s indicator light should be blinking.(see picture attached)

.

When you cover the camera’s photocell or put the camera in dark place, the infrared LED should turn on red color.

—>2. If camera powered on properly please follow below instructions.

1.Right-click mouse navigate to “Quick Setup(or Channel Set) –>Cancel

2. In the second box, if any camera status is offline or not connected, please select it and click ”Delete” first

3. Click “Search”, can you see new IP address showed on the topper box?

4. Select the IP address in topper box and click Network–>Auto Assigned–>OK

5. If auto assigned successfully, please click “Add” to add the camera.

.

.

G:  No Video Display on TV Monitor Or Blank Screen?

My UI Interface shows “No signal” or “Black Screen” ？

We need to divert this issue into two situations:

1.NVR Indicator light is on:

(1) Cause: The camera system’s video output resolution is 1080P. If your TV monitor resolution is below 1080P, this issue will occur.

Steps:

Please right-click and hold your mouse for over 10 seconds to see if the system can reboot or not. Or, please try to connect the system to another TV monitor with a higher resolution (above 1080P)

.

(2) Cause: The hard disk drive inside of the DVR box is broken, and use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is having an issue, and needs a replacement, plz contact email love@hiseeu.com for replacement HDD

After steps, if the thing still cann’t be resolved, which means the NVR box is broken, plz contact email love@hiseeu.com for replacement NVR box if their warranty is still 1 year

.

2.NVR Indicator light is off:

(1) Cause: The power adapter 52V 2.5 A connected to the NVR box is broken

Step: Use another power supply 52V 2.5 A to power on the NVR unit to have a try ( If you do not have a spare one, can contact us to buy a new one or we send you a new one if your warranty is still under 1 year )

.

(2) Cause: The hard disk drive inside of the NVR box is broken Step: Use the screwdriver to open the NVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the NVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is broken, and needs a HDD replacement, plz contact email love@hiseeu.com for replacement HDD

.

H:Why DVR/NVR can’t record or playback video?

.

If HDD(Hard disk drive) is having issue or something wrong with record setting, the DVR can’t record/playback the video

.

1.Check if the hard drive status is normal or error

Navigate to NVR/DVR Monitor UI Interface: Navigate to “Main Menu–>Advanced–>HDD info”

If status shows “Error” or No hard drive info , which means the hard drive is broken. (need to replace hard dirve)

2.Check the record plan is set up for 24/7 continuous recording

Navigate to “Main Menu–>Record Conf”

Channel : select “All”

Period: “00:00-24:00”

Select “Regular”

3. Please make sure the HDD was set up to “Overwrite”. (if it was set to “stop”, the system would stop recording when the storage is full)

Navigate to “Main Menu–>General–>Storage Full”

Add Device on Guard Station PC Client Software

Add device to “Guard Station” Download link: https://www.dropbox.com/sh/jeftu4sqwy4y1u8/AAD4PkyEJxg6j4H1n20PxBkZa?dl=0  

.

Please sign up for the mobile APP(Guard Viewer) account and add the device first.

Download and run “Guard Station” on the PC

1) Please Navigate to “Device Management”> “Cloud Device”> Click on “Login”

2) Login with your APP account and password.

3) After Login, the device you added to the APP will list here

Please click on “Control Panel”> “Live View”> Double-Click Camera to load the live view video

Add Cameras to NVR or PoE Switch (Router)

Add Cameras to NVR/ PoE Switch or Router

1. Add camera via NVR PoE Port

• If the camera is connected to NVR PoE port directly, the IP address

range should be modified to “172.16.0.X” (X is between 2 to 255)

Please right-click mouse and navigate to Camera

For brand new camera (password is 123456 by default), NVR will detect

and add camera automatically.

If the camera’s user name or password has been changed, you are required to input the info manually.

Move the mouse to the status icon , you will see the error message. “Offline [incorrect Username to Password]”

Please click on the edit icon to input password manually and click on “OK” to continue.

2.Add Camera to NVR via PoE Switch or Router

NVR will detect the camera under the same WLAN and list IPC here

• Click on plug icon to add the camera. If the camera has default user name: admin, password: 123456.

NVR will add it automatically.

• If the camera’s password has been changed, please click on the setting icon to modify the info.

• In this situation, the camera IP address range should be the same as NVR’s IP range

(You can check NVR IP by navigating to Network>Basic> TCP/IP). If not, please contact the technician to modify the camera’s IP first.

Camera Not working

Camera not working?

1.(Port issue) Insert the camera to another port of the NVR to have a try, and wait at least 5 minutes

2. (Camera issue) Make sure if the camera infrared light will turn on red or not in the night time

3. Also plz right click your mouse to “Menu-Camera”, and take a photo of this whole page and send it to us

（Check how many cameras are discovered）

Also go back to the home screen and Check connection status, to see if it shows” Network disconnected” or “incorrect user name and password”

Device Offline on APP or NVR?

Device Offline on APP or NVR?

If the device shows offline on mobile phone app  “Guard Viewer” , we need to make sure the NVR is connected to network perfectly or not

Go next to your Monitor that connected to NVR, and check out the network status

first navigate to this path first : “Menu–Network–Basic–P2P” , also check the device status is online or not,

if it shows: network disconnected, plz enable the DHCP in this path ” Menu–Network–Basic-TCP/IP ” and click “Apply” . After that, go back to “P2P” and check if the device status is online or not

Also , please make sure the PPPOE needs to be disabled, plz navigate to “Network–Advanced–PPPoE”

Enable Alarm light on Each Camera?

Enable Alarm light on Each Camera?

.

(Alarm light would only work during the night time when the alarm was triggered)

.

1. Set up the Alarm light First Right-click your mouse to “Menu– VCA — Intrusion Detection/Crossing Line Detection– Triggered Actions” , and draw the rules for the alarm type

After you set up an alarm type (Like”Intrusion Detection”, or “Crossing Line Detection”), Click on “Alarm Linkage”, you will have the option to Enable “Alarm Light” (Spotlight is only Available During the Night)

2. Enable Alarm Light on “Triggered Action– Alarm Light” for each channel, and Click “OK”

Forget NVR Password？

If you forget your current password, please follow the instructions to reset it.

1. In the system login interface, please click on “Enter Password” > “Forgot Password”

2.If you filled in your email address as a reserved email when you set up the system, you can reset the device password via the APP(Guard Viewer) by navigate to “Me–General–Forget Device Password”

3.Scan the above QR code by app and the security code will be sent to your email address.

4. Enter the security code from email to reset the password

Additionally, If you the email doesn’t belong to you, plz contact us at love@hiseeu.com for more support

Add Device to APP(Guard Viewer)

.

Auto add is not suggested. Please tap on “Later” if you see this message box.

.

In this situation, it will Auto Search to discover the NVR device connected to the local network. But once your mobile phone disconnects with LAN WiFi, you will not be able to view it anymore.

Please Add devices in this way

1.  Please Tap on “ Menu” icon> Tap on “Devices”> “Add”,

2. Tap on “Scan”> “OK” to scan the NVR QR code

3.Navigate to “Menu– Network> Basic> P2P”

• If the Device Status is “Network connected…” , means device is online   and ready for remote view

• If the Device Status is “Offline” , please check the network connection first, if the problem remains, please feel free to contact us at Love@Hiseeu.com   

After you add the device successful, the “Device status” will be “Online”, and your APP account username will display here.   • You can check your APP user name by navigate to “Me”

• If the username doesn’t belong to you, please click on “Delete” and add it again.

4.Add NVR by scanning device QR code and click on “save”

5.   Please Tap on “Menu ” icon, Tap on “Live View” “Add”

6. Select the device and tap on “Start Live View”

Human Tracking/Detect for Model PK-4YHD985-CT ?

1.To enable human tracking , Set preset point “21”. Here is the video link for your reference: https://www.amazon.com/live/video/07adae4ec34a47618bd754cc6c1f8966?ref_=dp_vse_ibvc1

2.To enable human detection, plz go to this path “Menu–Alarm-Motion” , and choose the camera you want, to enable it

(This doesn’t support customize area)

No Video on TV Monitor or blank Screen?

.

The camera system video output resolution is 1080P, if your TV monitor resolution below that will occur this issue.

.

If possible, could you please try to connect the system to another TV monitor with a higher resolution(above 1080P).

Or, please hold your mouse wheel over 10seconds to see if the system can reboot or not.

If not, plz contact us for further support

How to share Device to others via APP Guard Viewer?

.

One device linked to One User ONLY. The NVR system ONLY can be controlled by one authorized account, who can share the device with others in order to prevent attacking or hacking.

For admin user, please follow the instructions to share the device with others:

.

1.Type on “Menu Icon ” and navigate to “Devices”

.

2.Tape on “… ” > “Share”, You can select a single channel to share or select the entire NVR system to share

(1) Share device by typing in the user name you wanted to share with and selecting function as needed.

• The other user needs to register a Guard Viewer APP account and provide the user name for sharing.

• After that, when this user login the APP will find the device by navigate to “Devices”

(2) Share device by generate a QR code

• Create a sharing password and set the valid period

• Click “Generate”, your APP will generate a QR code

• Other users can use the APP to add the device by scanning the QR code you sent

Download the mobile APP and Sign up for an Account

.

1. Download and install the app.

Please scan the QR code to download the free APP “Guard Viewer”

You also can visit the Apple Store or the Google Play Store to download the Guard Viewer app for iOS or Android devices. Alter installation, tap the icon to launch the app.

2.Register an account and login

For first time use, please create a new account and add the following steps:

Please tap Sign up and follow the on-screen prompt to register an account by email.

<p>The post Hisseu PoE Camera System User Guide v1 first appeared on NVR IPCAMERA SECURITY.</p>

How to Change the Password on a 5.0 UI IP Camera

.

IPCamera/Change Password 5.0 UI

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the current username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the System option from the drop-down list

3. Select Account on the left.
Then select the User tab at the top.
Click on the Edit (Pencil) icon to the right of the user account who’s password you want to edit

4. Enable the Change Password slider.
Then enter the current password in the Old Password field.
Enter the new password you want to change it to in both the New Password and Confirm Password fields.
Click on OK at the bottom

5. Once the new password is successfully changed, you will see “Modify User Succeeded” at the top

Dahua IP Camera 5.0 UI Setup

How to Set the Date and Time on a 5.0 UI IP Camera

.

IPCamera/Set Date and Time 5.0 UI

Description

This guide will show you how to set the Date and Time on a IMaxCamPro IP Camera with the 5.0 User Interface

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the System option from the drop-down list

3. Select General on the left.
Then select the Date & Time tab at the top.
To set the date and time without an NTP server, select Manual Setting. Then adjust the Time, Time Format, and Time Zone. (You can press Sync PC if you want to pull the time from the PC you are using. The Time Zone still needs to be set manually though.)

To set the date and time with an NTP server, select NTP. Then fill in the information for a functioning NTP server. (This will only work if the camera has access to the internet.)
For locations that use Daylight Saving Time, enable the slider below DST and select the dates and times that Daylight Savings starts and stops.
When you are done adjusting settings, select Apply at the bottom to save the settings.

How to Set the IP to Static on a 5.0 UI IP Camera

.

IPCamera/Set IP to Static 5.0 UI

How to Set IP Settings to Static on a 5.0 UI IP Camera

Description

This guide will show you how to set the IP settings to static on a ImaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the Network option from the drop-down list

3. Select TCP/IP on the left.
Click on Static next to “Mode”.
Then fill in the IP Address, Subnet Mask, Default Gateway, and DNS settings below that. (You can press the “Test” button if you want to see if that IP address is free on your network.)
When you are done adjusting settings, click on Apply at the bottom

How to Configure Recording to an SD Card on a 5.0 UI IP Camera

.

IPCamera/Configure Recording SD Card 5.0. UI

How to Configure Recording to an SD Card on a 5.0 UI IP Camera

Description

This guide will show you how to configure recording to an SD Card on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the Storage option from the drop-down list

3. Select the SD card from the list by enabling the radio button on the left.
Click on Format at the top to wipe all the data on the SD card and configure it for recording on this camera.

4. Click on the Home icon at the top left.
Select Record. (If you don’t see it on the main page, click the right circle at the bottom to switch pages.)

5. Select the Record Control tab at the top.
Adjust the settings on this page as desired:

When you are done adjusting settings, click on Apply to save the settings

6. Select the Time Plan tab at the top.
Adjust each Event Type on the weekly calendar.
When you are done adjusing the schedules, click on Apply to save your changes

7. Select the Storage tab at the top.
Adjust the settings on this page as desired:

When you are done adjusting settings, click on Apply to save the settings

How to Playback Video from an SD Card on a 5.0 UI IP Camera

.

IPCamera/Playback Recording SD Card 5.0. UI

How to Playback Video from an SD Card on a 5.0 UI IP Camera

Description

This guide will show you how to view recorded video footage from an SD Card on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Click on the Home icon at the top left.
Select Record. (If you don’t see it on the main page, click the right circle at the bottom to switch pages.)

3. Select the Search Video tab at the top.
Select the start date and time, and the end date and time on the left.
Then click Search below that.
All the recorded footage on the SD card in the time range will appear.
Double-click on the specific clip you want to play

4. Move the slider at the bottom to adjust the playback time.
Use the controls to play, pause, rewind, fast forward, or jump between clips

IPCamera/Password Reset 5.0. UI

.

IPCamera/Password Reset 5.0. UI

How to Reset the Password on a 5.0 UI IP Camera

Description

This guide will show you how to reset the password on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

Reset via Password Recovery in DMSS

1. Input the camera’s IP address into a web browser.
Click on Forgot password?

2. Click on OK to agree to use your email address in this process

3. If you setup a recovery email you will be brought to a page with a QR code on it. (If you didn’t setup a recovery email, skip to “Reset via Physical Button” at the bottom of this page.)

4. Open the DMSS app on a mobile device.
Tap on Me at the bottom.
Then select Tool Manager

5. Tap on Device Password Management

6. Use the mobile device’s camera to scan the QR code from Step 3 above

7. Once the QR Code has been successfully scanned you will see the following message

8. Check the email inbox for the email address that was registered for password recovery on this device.
Input the security code from that email in the Security code field.
Then click on Next

9. Enter a new password in the New Password and Confirm Password fields.
Then click on OK

10. The password will be successfully reset

Reset via Physical Button

Depending on the model of your IP Camera, there could be a physical reset button on the outside body of the camera, or inside the camera body.

1. Reset: Press the reset button for 10-20 seconds while the camera is connected to power.

IP Camera Basic Info

Important Safeguards and Warnings

1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The product must be grounded to reduce the risk of electric shock. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.

2．Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.

3．Installation

4．Qualified engineers needed All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment The NVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. This series product shall be transported, storage and used in the specified environments.

6. Accessories Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package.

7. Lithium battery Improper battery use may result in fire, explosion, or personal injury! When replace the battery, please make sure you are using the same model! Before your operation please read the following instructions carefully.

Hardware Installation and Connection

Note: All the installation and operations here should conform to your local electric safety rules.

1. Check Unpacked NVR When you receive the NVR from the forwarding agent, please check whether there is any visible damage. The protective materials used for the package of the NVR can protect most accidental clashes during transportation. Then you can open the box to check the accessories. Please check the items in accordance with the list (Remote control is optional). Finally you can remove the protective film of the NVR.

2. About Front Panel and Rear Panel For detailed information of the function keys in the front panel and the ports in the rear panel, please refer to the User’s Manual included in the resource CD. The model label in the front panel is very important; please check according to your purchase order. The label in the rear panel is very important too. Usually we need you to represent the serial number when we provide the service after sales.

3. After Remove the Chassis Please check the data cable, power cable, COM cable and main boar cable connection is secure or not.

4. Important：Please turn off the power before you replace the HDD. You can refer to the User’s Manual for recommended HDD brand. Please use HDD of 7200rpm or higher. Usually we do not recommend a PC HDD. For detailed operation instruction, please refer to the User’s Manual included in the resources CD.

1. Use the screwdriver to loose the screws of the rear panel and then remove the front cover.

2. Put the HDD to the HDD bracket in the chassis and then line up the four screws to the four holes in the HDD. Use the screwdriver to fix the screws firmly to secure HDD on the HDD bracket

3. Connect to the HDD data cable to the main board and the HDD port respectively. Loosen the power cable of the chassis and connect another end of the power cable to the HDD port.

4. After connect the cable, put the front cover back to the device and then fix screws of the rear panel.

<p>The post Dahua IP Camera 5.0 UI Setup first appeared on NVR IPCAMERA SECURITY.</p>

Once you have the NAS setup you can come back to this post and follow the steps below:
.

Step 1: Login to your Synology NAS via a browser​

Step 2: Click the Package Center icon​

Step 3: Search for and install the Surveillance Station software (it should be on the home page of the package center, if not you can use the search bar to find it)​

Step 4: Click the Synology main menu at the top left of your screen and open the newly installed Surveillance Station software​

Step 5: Click the IP Camera icon​

Step 6: Click the add button when the new window open and then click add camera from the drop-down​

Step 7: Select Quick Setup and then click the next button​

Step 8: Enter the camera details manually or click the Search icon next the IP Address box​

Step 9: Check both the Synology Supported Cameras and ONVIF lists (some camera models are not directly supported by Synology, but as long as the camera is ONVIF compliant you should be able to add it to the Surveillance Station software)​

Step 10: Select the camera you want to add from one of the lists and click OK​

Step 11: Check that all the camera details are filled in, including the cameras username & password (also give the camera a unique name to help you identify it from other cameras)​

Step 12: Click the Test Connection button and if the test is successful you’ll get a green tick and a live shot from the camera, you can then click Finish and the camera will be added to your Synology NAS​

If the test is not successful you will have to go back and check the camera’s settings are correct, the most common problem is that the camera has an IP address that is not on your network, after you have followed our instructions from a previous video on how to change the IP address you should get a successful connection and be able to add the camera.

How To Install Synology Surveillance Station

Read Also : Dahua NVR Troubleshoot All Series

.

If you need more help with installing Surveillance Station and adding an IP Camera to your Synology NAS you can watch this video:

.

Synology NVRs and VisualStation​

NVR1218, DVA1622, DVA3221, VS360HD

NVR’s (Network Video Recorders) are a neccessary part of any security setup.
They work to store, playback and support the live feed of security footage from connected IP Cameras, and with Synology, can offer even more.

.

Offering a range of Network Video Recording solutions, from their energy efficient NVR1218, and compact VS360HD, to their deep learning, AI powered DVA series, Synology’s selection of NVRs were designed to appeal to a range of different users and applications.
At Use-IP you can now choose from these four Synology NVRs and decide which is best suited for your needs.
​

.

.

​

NVR1218​

The Synology NVR1218 is a 2-Bay (Reaching a max. of 7 bays, with an Expansion unit) Network Video Recorder, able to support a max. of 12 IP camera channels.
Its design is also fit for a PC-less experiance (only needing to be connected to a monitor) and can be accessed remotely, via Synology’s Surveillance Station, or, DS cam mobile application (allowing for Live view, playback, adjustments, and notifications, on a mobile device).

Key Features:
.

.

.

​

​

Deep Learning NVR (DVA) Series​

The Deep Learning NVR Series combines the Management features of Synology’s Surveillnace Station, with Advanced Analytics, designed to fit deployments of all sizes.
Intelligent Analytics – Included in DVA NVRs to strengthen on-premises security, offering deep learning algorithms and detection profiles
.

Users can choose between the more compact design of the DVA1622, or the larger storage of the DVA3221, the key features of which are both listed below.
​

DVA1622

DVA3221​

.

The DVA Series NVRs also come equipped with the use of Dynamic Maps, allowing for improved situational awareness, and to help users to determine camera/event locations, and provide instant access to video feeds for more efficient site monitoring. This also includes the features listed below:​

.

.

VisualStation

VS360HD
​

Synology’s VisualStation offers a PC-less, live view and playback solution, for your surveillance footage, with the ability to work in mobile environments.
Designed to work as a companion system, the VisualStation also offers an ultra-compact design, and features Synology SurveillanceStation live view and management tools. It is a perfect alternative for a Video recording solution, for users facing budget or space constraints.

Key Features:
.

How It Works:
Plug in an Ethernet cable, connect the VisualStation to a LCD-monitor or TV, log into the Synology SurveillanceStation – and its all set up, for quick and easy use.
.

The VS360HD is also equipped for use in harsh and mobile environments. With a design free from mechanical moving parts, the VisualStation is more resistant against vibration and hardware failure, than other Network Video Recording solutions.
Its design also features a solid outer case, built to keep it running in industrial temperature ranges (-20°c ~ 50°c)
This is what makes the Synology VisualStation both a cost effective, and reliable system, for any user.

.

Synology NAS/SAN Systems​

Synology’s Data Storage/Management Systems come in a range of styles and sizes, each designed to fit different user needs. Being able to appeal to a range of users and suitable for numerous applications, Synology’s NAS/SAN Systems are an ideal addition to any personal data management, business data management, or security setup.
Choose from Synology’s range of NAS types; RackStations, DiskStations, FlashStations, and more.​

What is a NAS?​

NAS = Network Attatched Storage.
A NAS is a device that provides users with a networked location to store their data, and are designed to be equipped for use at home or for businesses (or other applications).
But a Synology NAS has even more to offer, as they are designed to offer private cloud storage, backup systems, and secure file sharing.
​

Benefits For Home Use

The DiskStation Manager 7.0​

The DiskStation Manager is the operating system for Synology NAS systems, it was designed with focus on reliability and impressive performance, and offers users a wide range of data management features.​

Users can also feel secure when using their Synology NAS, as the DiskStation Manager offers Secure Sign-in, with app-based login approval, hardware security keys, and 2-factor authentication options. Keep your data, and your data management, as secure as possible.

.

Data Backup Solutions​

With the DiskStation Manager as its operating system, a Synology NAS will also offer users a selection of effective and reliable backup solutions, which include:
.

Active Backup for Business
Expands user data protection with agent-based Linux backup, possible for five major distributions, and AES-256 encryption.

Active Backup for Microsoft 365 / Google Workspace
Maintain offsite copies and restart backup tasks in a different location.

Hyper Backup
Protect data with backup support for DSM settings and 12 additional software packages.

Synology C2
Synology’s Cloud Storage Solution
Back-up NAS data to the cloud (with Hyper backup), and, sync requested data between C2 storage and branch offices (with Hybrid share)
​

Synology NAS Systems also include the Btrfs File System, that allows for even more backup solutions, so users can keep their data as secure as possible (keeping data safe even in the event of data corruption or system failure). These Solutions include:
.

.

.

.

Synology’s NAS Lineup
Now Avaliable at Use-IP​

​

RackStations​

A selection of Rackmount style NAS Systems.
Synology RackStations offer impressive performance and large storage space, all in a rackmount design.
​

XS+/XS Series – RS4021xs+, RS3621xs+, RS3621RPxs, RS1619xs+
+ Series – RS422+, RS820+, RS820RP+, RS1221+, RS1221RP+, RS2421+, RS2421RP+, RS2821RP+
Value Series – RS819
.

DiskStations​

A style of NAS perfect for a Desktop application.
Synology DiskStations range from being compact storage solutions for Business environments, to being an ideal starting point for Home users.
.

​

XS+/XS Series – DS3622xs+, DS1621xs+
+ Series – DS220+, DS420+, DS620slim, DS720+, DS920+, DS1522+, DS1621+, DS1821+, DS2422+
j Series – DS220j
.

FlashStations​

Synology’s FS Series, with an All Flash Array, Rackmount design.
Synology FlashStations offer uncomromising performance, and solid-state drives. Perfect for more demanding applications, and to accelerate Business operations.
.

FS Series – FS6400, FS3600, FS3400, FS2500

.

SA, HD, and, UC Series​

All in a Rackmount style, these NAS systems appeal to a range of storage requirements.​

SA Series – Offers a Scalable storage solution (ideal for enterprises) with high-performance and capacity requirements. – SA3600, SA3400, SA3200D
HD Series – Offers a High-density SAS Storage server, designed for Rapid data scaling, optimizing operational efficiency, and IT infrastructure.- HD6500
UC Series – Offers a dependable high-avaliability SAN Storage solution, fit for iSCSI and FC environments. – UC3200

.

.

​

Expansion Units​

Synology NAS/SAN Systems can also be expanded, with compatible Synology Expansion Units.
Increase your storage space by adding additional drive bays, using a range of Expansion Unit models, also avaliable at Use-IP

FX2421 – Expansion for FS6400, FS3600, and, FS3400
RX6022sas – Expansion for HD6500
RXD1219sas – Expansion for SA3200D and UC3200
DX1222 – Expansion for DS3622xs+ and DS2422+
RX1222sas – Expansion for SA3600 and SA3400

<p>The post How To Install Synology Surveillance Station first appeared on NVR IPCAMERA SECURITY.</p>

Safire NVR Setup Guide

Read Next :

• XMEYE NVR Installation Guide
• ClareVision NVR and Camera General Guides
• UNIARCH NVR DVR Full installation user manual

Email settings in Recorders and Cameras: Gmail and Yahoo

Let’s explain how to add these two servers to a recorder or camera, bearing in mind that it may be easier to do so with Yahoo as there are fewer steps to configure.

GMAIL

The data of this mail server are the following:

Smtp server: smtp.gmail.com

SMTP Port: 587

Enable TTL

It’s also important to enable POP and IMAP in your mail.

It is also necessary to activate the sending of emails from less secure applications, from this tab: https://www.google.com/settings/security/lesssecureapps

IMPORTANT: Do not enable two-step gmail protection

Example: brand Safire Safire with Gmail

YAHOO

Smtp server: smtp.mail.yahoo.com

SMTP Port: 587

Enable TTL

Example: X-Security brand with Yahoo

VCA (Area Intrusion Detection) configuration concepts from a SAFIRE video recorder

Threshold: Time, in seconds, that the target must remain within the detection zone to generate an alert.

Sensitivity: Inverse of the percentage of the target area entering the detection zone, relative to the total target area, to generate an alert. The formula that describes this concept is A/A+B>100-S, where A is the target area within the zone, B is the target area outside the zone and S is the sensitivity. A value of 80 will only trigger the alert when at least 20% of the target enters the area.

Percentage: Minimum area (in percentage) of the detection zone that has to be occupied to generate an alert.

Follow a guide in English for installation and configuration of VCA rules

SAFIRE How to setup …pdf

Slot for SD card in camera SF-IPSD6525UAWH-2

To find the space dedicated to the SD card, follow the hereby attached scheme:

Activate PIR detection and alarm sound on SF-IPCU202AWH-2W

With this configuration the PIR will alert our mobile device and the camera will emit an alarm sound in case of detection or event.

These two options can be managed from the camera’s own web interface.

To arm and disarm the PIR notifications, it is possible to configure it from the app (while the sound management has to be managed by web).

Installation and Configuration manual of TrueSense technology

<p>The post Safire NVR Setup Guide first appeared on NVR IPCAMERA SECURITY.</p>

How to connect a Uniview Cube camera to wifi using a PC

<p>The post Advanced Uniview IP Camera Guide first appeared on NVR IPCAMERA SECURITY.</p>

<p>The post XMEYE NVR Installation Guide first appeared on NVR IPCAMERA SECURITY.</p>

How To: Access Your Recordings On The WLNVR via the RXCamView App

Recordings and images will be stored here.

In the RXCamView App, press the person icon in top left corner to open menu.

Select file list.

Here you can see all images and video files recorded onto the device.

These are easily sharable through the app via your email account or even to Google Drive.

How To: Set Up Email Notifications Via The WLNVR Unit.

The device cannot directly send an email itself – you must give it permission to send from an account you have access to (this doesn’t have to be an email account you use all the time, you could set one up just for the recorder to use).

Once you have the email account set up, make note of the username and password.

Next, find out the SMTP addresses of the mail provider (in this example we will use Gmail, however the details will be different for different email providers. The easiest way to find out is to google it) and keep note of this.

Gmail SMTP server address: smtp.gmail.com

Gmail SMTP port (TLS): 587

Gmail SMTP port (SSL): 465

On the main screen of the NVR, right click to bring up the menu along the bottom.

Click the menu icon in the bottom left to bring up the small pop up menu.

Hit set-up and then Network > Email.

Tick the Email box at the top

Change encryption to SSL

Enter the SSL port number in the box below (465 for Gmail)

Enter the SMTP server next (smtp.gmail.com for Gmail)

Next enter the username and password for the account you would like to send from

Enter the name you would like the email to be from in the Sender box (e.g. CCTV Motion Alerts)

Next you can enter up to 3 addresses to receive the email notification.

Using the Interval drop down box, you can set how often these alerts are sent with continued motion alerts.

Finally, you can click through to email schedule, where you can set it to only send alerts for motion at certain days/time but also set exceptions for it to not send an email, e.g. if you know someone will be home at that time.

Wireless Recorder Kit Setup Guide

Read Next : HiSeeu Wireless Camera System installation guide

How To: Set Up The WLNVR From The Box

Initially the NVR will require a screen/monitor with a HDMI input to get it set up, however once all the settings are in place you can happily disconnect it and repower it somewhere else with a wired network connection and it will be controllable via the app!

Repeat for any other cameras – each NVR will support up to 6 cameras.

Setting Up Using The Wizard 

Network:

In most cases it will be fine to leave the network settings on default

DCHP will allow your router to automatically assign the device it’s IP address

Changing these settings is for advance networking only

Date & Time:

Set current Date and Time along with any format preferences

Here you can also set daylight savings time

HDD:

Here you can format the HDD and any SD cards inserted by selecting the small circle to the right of the memory device and then clicking format HDD.

This may take several moments

Resolution:

Here you can change the resolution to suit your monitor or screen or to lower the frame rate to save on disk space (this may lower image quality)

Mobile App:

Next you can add the device to the RXCamView App by opening the app, adding device and scanning the QR code.

Summary:

Here you can quickly review your settings before clicking finish and saving.

Remember to check the box to save the wizards settings.

How To: Pair Your Cameras To The WLNVR

Pair your cameras by pressing the small white button on the back of the main camera unit, the red lights will flash to show that it is in pairing mode.

On the screen of the recorder, hover over one of the camera channels and press the sideways camera icon in the middle at the top.

This will pair the camera to that channel on the recorder.

<p>The post Wireless Recorder Kit Setup Guide first appeared on NVR IPCAMERA SECURITY.</p>

How to set presets & auto-patrol for xmartO PTZ cameras?

The xmartO WT series, DZ series and DPM series PTZ cameras support up to 8 preset points.

Definition of ‘presets’: PTZ cameras can be navigated to view different areas. Presets record the key points so you can reach the recorded poinits with one tap.

Auto-patrol: a feature xmartO developped based on preset feature. The camera patrol the preset points back and forth. AKA auto-cruise, auto-scan.

1. Set preset points

While viewing the camera, tap PTZ icon to enter PTZ menu; then tap Preset to enter preset menu. Use the joystick to navigate the camera to the 1st point, tap ‘Add Preset’ to save the point 1; then navigate the camera to next point and tap ‘Add preset’ to save the point 2…you can save up to 8 points.

2. In the preset menu, you can tap ‘Go to‘ to reach the preset points.

3. Start Auto-patrol

a) If your camera does not have optical zoom, tap the image, on right you will see the A icon. Tap the A icon the camera will start to patrol the preset points.

b) If your camera is the version with optical zoom, well it has higher level chipset inside. The Auto-patrol is a bit different. In preset menu, tap ‘Shortcut mode’, type in ’13’ and tap Go to, the camera will start to patrol the preset points.

4. Stop Auto-patrol

Tap any of the direction on the joystick will stop the auto patrol.

Tips: cameras added to xmartO NVR have the same steps. It’s similar to on the NVR. Only the NVR’s UI is a bit different and the A icon is in the middle of the joystick. 

Read Next : How to Set up Alexa for Blink devices

View XMARTO WiFi cameras on PC

CMS is called Camera Monitor System. It is a camera monitoring client for online preview image, video storage, remote playback, device management, video/screen download and other functions. It is suitable for DVR, NVR, IPC, VR CAM, Wifi IPC and other devices.

Below are the basic instructions of using CMS on your computer. If you need detailed user manual of CMS, you can download it from our website: https://xmarto.com/pages/download

Also, you can click More Function-System Message-Open the manual to find more details of xmartO WallPixel CMS.

1. Download xmartO WallPixel CMS Software
Link: https://www.xmarto.com/downloads/

2.Installation and operation  

Step 1: Run the xmartO_WallPixel_for_PC_Setup.exe installation package.

Step 2: Select the language that your system needs to use.

Step 3: Read and accept the agreement.

Step 4: Select and determine your software installation path.

Step 5: After the installation is successful, immediately run and use.

 

3. Login

3.1 Local Login

Default username: admin
Default password: no password, leave it blank

For security reason, we suggest you set a password after you are logged in.

3.2 Cloud Login

Use the app account: Enter the username + password of the app account on the cloud login interface to log in.

Register an account:Click on the registered account in the cloud login interface, enter the mobile phone number / email (if using the mobile phone number to register, you need to add the mobile phone number area code), click OK, enter the password and verification code and click Register now, after verification, you can complete the registration.

Forgot password:Click on the forgot password in the login interface, enter the registered account to obtain the verification code, enter the verification code and the new password and click OK to reset the password.

 

4. Add Device to CMS

You can add devices to the CMS in two ways:

Method 1: After adding the device using the mobile APP, directly log in to the CMS using the APP account password, and you can view the device you have added in the CMS system;

Method 2: Please make sure that your device is equipped with a network or a network cable, log in to the CMS, and click the add button in the upper right corner.

Add IP / DDNS: manually enter the device “IP / DDNS + port + channel number + device password”, select “type” according to the actual situation of the device, the rest of the information remains the default, click Finish to add successfully.

Cloud ID addition: manually enter the device “cloud ID number + channel number + device password”, select “type” according to the actual situation of the device, the rest of the information remains the default, click Finish to add successfully.

 

 

LAN search device addition: select the device management in the function bar below the system, click the interface refresh button, wait for the device to be searched, check the required device and click add (enter the device IP / ID to quickly find the need to add device)

5. Live View
The xmartO WallPixel  CMS allows you to view cameras on your computer both locally and remotely.

5.1 Main Menu Introduction of CMS:

• Playback: Click to playback videos stored in your hard drive
• Device Management: Manage your device(s)
• User Parameter: Some basic settings of CMS
• Record: Record short videos of live view cameras, videos will be stored to your computer
• Screenshot: Take snapshots of live view cameras, pictures will be stored to your computer
• Disconnect All: Turn off live view of all cameras on CMS
• Screen Number: Choose how many cameras you want to display on one screen, the CMS allows you to view up to 64 cameras simultaneously
• More Function: More basic functions of CMS, including creating user, setting password and etc.

5.2 Multi-channel Viewing
CMS allows you to view up to 64 cameras simultaneouly. So if you have multiple systems, you can view all cameras in multiple systems simultaneously on this CMS.

5.3 Record and Snapshot
CMS allows you to record short videos and take snapshots when live view cameras, videos and snapshots will be saved in your computer. You can change the storage path here as shown in the picture.

 

6. Playback
CMS allows you to playback your history videos stored in hard drive. With this CMS, you can playback videos stored in hard drive or micro SD card from all over the world. Detailed instruction as below:

a. Click “Playback” on bottom navigation, it will pop out message “Close the video being played?” Choose Yes.
b. Select a window on left(1), select a channel from the device(2), choose the Record Type, select a date(3), and click “Retrieval”(4). The CMS will start playback videos of that channel immediately. Move the cursor on the time bar at bottom to locate an exact time to replay the camera per your needs.

c. You can record short videos or take snapshots while playback videos. Videos and snapshots will be stored to your computer.

 

7. Backup 
CMS allows you to download and backup videos to your computer.
The downloaded video files are in .mp4 format, you can playback with any player.

Detailed instruction here:
Click “Playback” on bottom navigation, select a device channel, choose Record type, select a date and then click “Download” on bottom right. You’ll see below interface with a list of all recorded videos.

 

Videos will be saved to your computer, as shown in below picture. You can also change the storage path.

 

8. User Management

8.1 Change admin password
Click “More Function” on bottom navigation, choose “System Message” and click “Change Password”. Keep the old password blank, and enter your new password, confirm your new password, and click “Confirm” to save it.

 

Something important need to pay attention to:
If you have once installed old ESeeCloud version on your computer and plan to upgrade to this new one, you need to uninstall the old version from your computer completely, and delete related files. Then install this new version, otherwise the new one does not work on your computer.

Here is how to uninstall the old one and delete the related files from your computer:
1. Uninstall the current ESeeCloud software from your computer.
2. Go to the place where you install this software on your computer and delete the file named with ESeeCloud completely, usually it is stored here:  C:\Program Files (x86)\EseeCloud
3. Go to below path and delete the ESeeCloud file, as shown in below picture.
C:\Users\Administrator (or your username)\AppData\Local\EseeCloud
C:\Users\Administrator (or your username)\AppData\Local\EseeCloud_Data
C:\Users\Administrator (or your username)\AppData\Roaming\EseeCloud

If the file is not shown there, then you need to check “show hidden files, folders and drives “, as shown in below picture.

How to view xmartO cameras on Mac?

EseeCloud is an updated CMS to preview, playback and backup the xmartO cameras/ camera systems on Mac.

1. Download ESeeCloud CMS Software
Download the EseeCloud CMS from xmartO website:
https://www.xmarto.com/downloads

2. Install and run ESeeCloud CMS on your Mac.
Install the CMS on your Mac and run it. If you have problem installing ESeeCloud CMS to your Mac, please refer to,

https://support.xmarto.com/?action=faq&cat=1&id=20&artlang=en

3. Login ESeeCloud
After that, you will be asked to type in the username and password. The default username is “admin”, default password is blank. For security reason, please set a login password to prevent unauthorized access.

4. Add Device to ESeeCloud CMS

4.1 Auto add, applies to add devices in LAN
EseeCloud CMS will search the devices in LAN automatically and display them in the Device Management list.

a. Click “Device Management” in upper navigation, you’ll see your device(s) listed there.
b. Select the device(s) and click Add. Your device(s) will be added to ESeeCloud CMS. They will show on upper right.

 

c. Go back to Live View, and click on the “play button”

behind each device to preview. If you want to view cameras from all devices at the same time, simply click “All Connect” at the right bottom. Click on the “stop button” behind each device to stop previewing cameras of this device.

4.2 Manual add, applies to add devices remotely
If you want to view cameras from a remote computer, you need to add the device to your ESeeCloud CMS manually on that computer.

a. Run and login ESeeCloud, then click “+” at top right corner. Or click “Device Management” on upper navigation.

b. You’ll see below interface. There are two ways to add device to ESeeCloud: Add cloud ID and Add IP/DDNS.
Add cloud ID: Add device to ESeeCloud with your NVR’s Device/Cloud ID. It is available for local and remote access.
Add IP/DDNS: Add device to ESeeCloud with your NVR’s IP address. It is available for local access only, so if you want remote access your cameras on this computer, choose the first Add cloud ID.

c. Type in the information required and click “Add”, the device is added to this ESeeCloud CMS, you can preview the cameras now.

Note: If you are adding xmartO VR camera, please turn on the Panorama.

5. Live View
5.1 The ESeeCloud CMS allows you to view cameras on your computer both locally and remotely. Please refer to below image for basic introduction of buttons.

5.2 It allows you to view up to 64 cameras simultaneously.

5.3 It supports all xmartO security camera systems and VR cameras. You can turn on panorama for VR cameras here, and also you can turn on the auto cruise.

6. Playback
The ESeeCloud CMS allows you to playback your camera videos. With this CMS, you can playback videos stored in hard drive or microSD card from all over the world. Detailed instruction as below:

a. Click “Playback” on upper navigation.
b. Select a window on left(1), select a channel from the device(2), choose the type(3), and select a date(4), click “Search”(5). The CMS will start playback videos on camera windows shortly. Move the cursor on the time bar at bottom to locate an exact time to replay the camera per your needs.

Note: The ESeeCloud CMS allows you to playback 4 cameras at the same time.

7. Backup (It works in LAN network only)
The ESeeCloud CMS allows you to download and backup videos to your computer.
The recorded video files are in .avi format, you can playback with any player.

Detailed instruction here:
Click “Resource Management” on upper navigation, then select the channel you want to back up, select the type and date, click “Search”, you will see the recordings on the left. Click the “Download” icon to download the videos you want. Videos will be saved to your computer.

Videos will be saved to below path in default:

/Users/macusername/cms_data/cms_video_download/

You can change the storage path here:
Click the setting icon at upper right corner, then you’ll see below box. Click the three dots to change the storage path, and click Confirm.

8. User Management
8.1 Change admin password
The ESeeCloud CMS’s default username is admin, and default password in blank, means no password. For security consideration, we suggest you set a password for CMS after logged in. Here is how:

Click the “human” icon at upper right corner, then click Change Password. Keep the old password blank, and enter your new password, confirm your new password, and click Confirm.

 

8.2 Add new user
You can add new user for ESeeCloud CMS, here is how:
Click User Management on upper navigation, then click New, you’ll see below box.
Enter a username and remark name, click Confirm. (Remark name here is your nick name.)

Note: When you create a new user, you are not asked to enter new password for this user. It uses default password blank. You can change the password after logged in.

How to view cameras on the mobile app (WallPixel)

1. Download and install WallPixel App

Download the free WallPixel mobile app from App Store or Google Play Store and install the application on your phone or tablet.

          WallPixel HD

2. Creating an Account                                                                                                   

Tap the app, click “Register”, enter the required information to create an app account.
If you already have an account, login with your username and password.

After click “Register”, input your phone number or email address then the app will send you the verification code.

Check the email or text you’ve received and input the verification code.

Then you need to set a password and confirm it again. (The password should be a combination of 6-20 numbers or letters.)

At last, click “OK”,you’ll create the account successfully.

3. Adding NVR Device to App

Tap “+” at the top right corner, then tap the first option ” Wifi Camera Kit with NVR” to add your NVR device to the app.

4. Entering Device Information

Enter the required device information and click Save.

Cloud ID: This is your system’s Device ID, which can be found at the right bottom of your monitor. It is 9 digits. (NVR Device ID can also be found at NVR’s System setting – Network setting)
Username: Your NVR login username, default is admin. If you’ve set a new user for your NVR, use the new username here.
Password: Your NVR login password, default is empty, means no password, leave it blank. If you’ve set a new password for your NVR, make sure to type in the new password here.

* You can also scan to add your NVR device to the app.
a. Right click your NVR mouse, then click System setting – Network setting, click “Show QR Code”. The Cloud ID QR Code will be displayed.
b. Open the app, click + at upper right corner, then choose Scan and scan the QR Code displayed in your NVR’s network setting interface.
c. Enter your NVR’s login username and password, save the settings. Your device is now added to app. You can start live view cameras now.

5. Viewing Cameras on Phone

Once you click “Save”, the device will be added to your account and you’ll be directed to the device list page. As shown in below picture. Click the device to start live viewing your cameras.

6.View live video on mobile

Playback: You can playback the recorded videos in HDD on your mobile. Select any channel and click playback to review recorded videos of that channel.

Window: You can choose to view 1/4/6/8 cameras at a time.

Aspect Ratio:You can adjust the aspect ratio of the cameras’ image.

SD: Change live view resolution. You can select from HD or SD. HD means high definition resolution, while SD means standard resolution.

7.My account info.

Personal info: View your account information and change the password.
App setting: Some basic settings for your app.
Version: Your current app version.
Logout: Log out your current account.

How to view xmartO cameras on Alexa Echo Show?

Now all of our xmartO products can work with Alexa.

Pls see the details in the following link to view your cameras on Alexa Echo Show:

https://m.media-amazon.com/images/S/aplus-media/sc/37fa1474-c687-4fdf-af21-76a8b73f4b28.pdf

How to set camera’s light mode on the NVR? (solves black night vision)

The light mode of each camera lets you select which lights to use.

Click the camera image, it will pop-out a quick menu on bottom, pls click Color & Light-Light Model.

Infrared mode: uses IR LEDs only. At night you see B&W night vision. And the camera will then automatically adjust the day & night vision.

full color mode: flood lights stay on at night, you see color night vision.(Only cameras with floodlight can do it)

smart mode: B&W IR night vision when nobody detected, flood lights automatically turn on when people detected.

How to Upgrade xmartO IP camera firmware

OTA upgrade cameras firmware from APP (for standalone cameras)

1. For standalone cameras, in the APP device list, tap “…” at upper right corner of your device, choose “Settings”. It will show a red dot if there is a newer version.
2. Tap the red dot to upgrade your camera from OTA server.

It will take a few minutes to update your camera; and the update requires your camera to have good Internet connection.

Upgrade camera firmware from NVR

For multiple-camera systems, if you want to upgrade the cameras, you will need to do it from the NVR menu with an USB stick.

1. Please download the camera’s new firmware from xmarto.com or contact customer support for new firmware

2. Copy the firmware to an USB flash disk’s root directory (not in any folder)

3. Plug the USB flash disk to your NVR’s USB port

4. Go to System setting-CH Setting- IPC Maintenance, choose the firmware from USB Storage, and click start to update the firmware of your camera.

The camera will be uprgraded and you will see a new version.

Tips: if your NVR has only 1 USB port, click Start, the NVR will start a 60-second count down. Within 60 seconds, unplug the mouse and plug the USB flash drive, your camera will be upgraded. 

How to enhance WiFi connection between cameras and NVR?

While using XMARTO WiFi security camera system, customers may experience video freeze, video lag or even “no video” issue.

This is typically caused by weak WiFi signal from cameras to the NVR.

Based on 2.4Ghz WiFi, all cameras connect to the NVR’s own WiFi, just like your phones/ tablets connect to your home WiFi router.

In line of sight, XMARTO WiFi cameras can be mounted 1000ft (300m) away from the NVR. The camera system handles distance very well.

However, like any WiFi devices, the cameras do not handle obstacles very well. Each wall reduces its WiFi strength noticeably.

How Obstacles Affect Your Signal Strength

When your wireless signal is transmitted through various materials, such as walls and windows, the signal strength is affected. Though the NVR and wireless camera may be very close in proximity, you could still notice high signal interference if the signal passes through certain obstacles. For instance, if the signal passes through a concrete wall it will be severely weakened. Please reference the below chart to see which obstacles highly affect your signal and which do not.

Based on the facts, below are some suggestions of how to optimize your cameras’ WiFi connection.

1. Select a WiFi channel with least interference for your NVR

As the only hub, the NVR’s WiFi performance is crucial. To select a least-interfered WiFi channel for the NVR, ensures its performance not affected by other WiFi devices.

This is how to,

A) In NVR’s System setting – Network setting – WiFi setting. Click “Auto Select Channel“, the NVR will automatically select a WiFi channel with least WiFi interference.

B) For Japanese customers, you can choose region MKK and channel “Other” (channel 14) to avoid some WiFi interference.

2. Place your NVR and cameras reasonably

The NVR is the only WiFi hub, all cameras are WiFi devices that need to connect to the hub. Centralize the position of the NVR so it reaches all cameras well.

Principle of placing NVR and cameras: avoid any possibly avoidable wall, in the line from NVR to cameras.  

Do not place near high voltage wires or other sources of electrical interference. Electrical interference will degrade the quality of the signal.

Below are some more tips:

 

 

If there has to be obstacles between the NVR and camera, adjust the height of camera or NVR to avoid floor. Floors are normally heavier than walls.

Always find possible open between NVR and camera, mount camera and place NVR’s spot accordingly to allow signal to pass.

Metal walls (including metal garage gate) absorb wifi signal. Use extra extendable wifi antenna to bring camera’s antenna inside the wall. This also works for heavy concrete wall.

Try to keep camera and NVR’s antennas parallel to get better signal pick-up.

3. Bring the camera’s antenna through a wall

If a camera needs to be mounted behind a wall, you may use a WiFi antenna with extension cable to pass the wall.

Search “WiFi antenna with extension cable” on retail website like Amazon, you will find a lot of options.

Mount the camera behind the wall, drill a hole, wire through the hole to bring the antenna inside the wall.

4. Take advantage of XMARTO Dream Liner WiFi Relay technology
The xmartO Dream Liner technology uses cameras in middle as repeaters. That way, further cameras connect to closer cameras 1st, and then to the NVR as a group.

The latest G3 XMARTO WiFi camera systems do it automatically.

WiFi Relay

G3 Auto WiFi Relay

Here is an article about WiFi Relay,

https://support.xmarto.com/index.php?action=artikel&cat=1&id=32&artlang=en

5. Use a WiFi camera repeater

Add an RPT20 physical WiFi camera repeater for that camera,

6. Hard Wire Cameras
If you cannot get a camera to work via WiFi anyway, you should consider to hard wire that camera, especially when it’s PTZ camera.

Here is how to hard wire a camera,

https://support.xmarto.com/?action=faq&cat=1&id=50&artlang=en

How to pair a camera to an XMARTO NVR?

After you purchased an extra add-on camera, or when you want to swap a certain camera, you need to pair the new camera to your NVR.

1. Add by WiFi (for most cameras)

XMARTO’s “Add Cam by WiFi” feature makes this super easy.

1. Bring the camera close to the NVR, plug it to power.

2. On NVR screen, right click to enter main menu > Add Cam by WiFi. The NVR will search and add the new camera(s). Done.

The new camera will be added to NVR channel within a miniute.

What if: If this does not work, hold the camera’s reset button 6 – 10 seconds to bring the camera into config mode. Run “Add Cam by WiFi” on NVR.

 

2. Add with Ethernet cable (for cameras without reset key)

 Another way: pair the camera with an Ethernet Cable.

1.Plug the new camera to power. Use an ethernet cable to hardwire the camera to your NVR’s LAN port.

2. On NVR screen, right click to enter NVR’s main menu > Camera Manage.

3. In upper box, click “Refresh” button to search the camera out. The camera will be listed out an initial IP address 192.168.1.xxx

4. Click to select the camera, then click in below box to select an empty channel.

5. Click “Match Code“. The system will start to pair the camera to NVR’s WiFi.

6. Within a minute or so, the camera will be successfully paired to channel and displays image. You can now unplug the camera and mount it to where you want.

How to set a closer camera as a WiFi repeater for a camera that is out of WiFi range?

Start from Generation 3 (NVR and camera with ver.3.0+), XMARTO WiFi camera systems come with AUTO WiFi Relay.

AUTO WiFi Relay: when a camera is having weak WiFi signal. It shall come in and out frequently. Such a camera will AUTOMATICALLY find a close-by camera as WiFi repeater, connect to that camera, thus to relay back to the NVR.

First of all, to get good WiFi connection for cameras, you should decide your NVR’s location and WiFi channel well.

1. Centralize your NVR location so it reaches all cameras well.

2. Use a WiFi channel with least WiFi interference, here is how,

A) In NVR’s System setting – Network setting – WiFi setting. Click “Auto Select Channel“, the NVR will automatically select a WiFi channel with least WiFi interference.

Dream Liner Auto WiFi Relay

Q1: How do I know whether the Auto WiFi Relay is on?

A1: It’s set on by default. Right click to enter NVR main menu – WiFi Relay, you can see the status.Make sure Auto WiFi Relay is checked.

Q2: How can I take advantage of AUTO WiFi Relay?

A2: Since it’s an auto feature now, you don’t need to do much setting job.

Here is our suggestions:

Before mounting your cameras, simply place all cameras where you want, plug them to power, wait up to an hour to see whether all cameras can stream smoothly to the NVR. If they do, mount them; if they don’t, adjust the location of your NVR, or a certain camera, till you get a stable connection for all cameras, then mount them.

When you do the test run, most cameras shall be able to connect directly to the NVR. A certain camera that is far, or with more obstables may have weak WiFi signal to connect to the NVR. It may come in and out. When it’s coming in & out, it trys connecting to the NVR as always. If it feels hard to connect, it will find an alternative – a middle camera as repeater.

This is an algorithm, it may take up to 30 minutes for the camera to form a relay chain; and suprisingly you may find it’s a changing relationship. Maybe in the morning the CAM2 connects to CAM1, in the afternoon you find CAM2 connects to the NVR directly.

It’s not hard to understand. WiFi signal is something invisible and changing. Maybe in the afternoon you had your iPad in your room, your NVR in the living room is less interfered, CAM2 finds the NVR itself a better hotspot to connect.

After the test run, as long as you have all cameras streaming well to the NVR, you can mount them to their tested spots. (regardless how many WiFi bars they give you)

If you do have a camera that is hard to connect after adjusting other cameras’ locations, you should go ahead to mount the other cameras, then come back to this very camera.

You have 2 solutions：

1. Hard wire that camera, here is how to,

https://support.xmarto.com/?action=faq&cat=1&id=50&artlang=en

2. Add an RPT20 physical WiFi camera repeater for that camera,

====

Version 2 camera systems

For customers who has older version 2 camera systems, you can manually set a middle camera as a WiFi repeater. Click to see more details

 View More >> 

How to enable PTZ camera auto tracking on the NVR/Phone ?

When you add the PTZ cameras to the exsisting system as add-on cameras:

Go to System setting-CH Setting- Video Detection and enable the Motion Detection Tracking

On NVR version 3.2+

1. Click the image of a camera to pop-out the quick menu on bottom. Click ‘PTZ control’ to enter PTZ menu.

2. In PTZ menu, use the joystick to move the camera to where you want. Type preset ‘1’ and save. This point is saved as preset #1.

3. Enter ‘Auto tracking’ menu, check ‘Motion detection tracking’ and ‘Home point’, type preset 1 as the home point and Apply.

The camera will return to preset 1 after the tracking.

On the phone：

Run the app, click “…” at upper right corner of your device, Choose “Device Setting”

In “Smart Detection“, Enable the Motion Detection Tracking

====

If your NVR firmware is earlier than 3.1.4.4, or your camera version is older than 3.6.28; you need to upgrade your camera/ NVR to obtain the auto track feature. 

1. Update your NVR version to 3.1.4.4 or higher

Online upgrade: make sure your system is getting online condition.

Right click your NVR mouse>System setting>System Admin>System upgrade, choose Online upgrade, check upgrade when download finished, click Start.

2. Download the camera firmware 3.6.28,

https://www.xmarto.com/download/firmware/IPG5323_W_20210803_3_6_28_572010(1).rom

3. Put the file to your USB flash disk’s root directory, not in any folder.

4. Plug the USB flash disk to your NVR’s USB port.

5. Go to System setting-CH Setting- IPC Maintenance, choose the firmware from USB Storage, and click start to update the firmware of your camera.

6. Go to System setting-CH Setting- Video Detection and enable the Motion Detection Tracking

Now, your PTZ camera DZ2034/DZ20313, DT3034/DT30320, WT2054/WT20512, DPM2024 can achieve the auto tracking function when they connect to the NVR system.

==

XMARTO PTZ cameras has a lot of advanced features if you are interested. Please refer to the XMARTO PTZ camera command codes manual,

https://cdn.shopify.com/s/files/1/0628/9912/6502/files/XMARTO_PTZ_Dome_Camera_Command_Codes.pdf?v=1649837464

How to set home point for XMARTO Auto-Track PTZ cameras?

The XMARTO PTZ cameras have Auto-Track function. The Auto-Track is an AI feature that tracks activities and record.

It makes sure to record what happened even while you are not watching.

A concern comes along with the Auto-Track: would the camera track and view the wall or ground, and never come back to the entrance it was watching?

You can set a home point for the PTZ cameras. The camera will return to this key point after each track. 

Follow below steps, you can set your default view point.

1. Set Home Point On APP

While viewing the camera in App, tap PTZ and use the joystick to move the camera to watch the spot you want. (such as an entrance)

Then tap Preset to enter preset menu.

In Preset menu, tap the + sign to add preset points.

The 1st preset point will be the home point.

The camera will return to this point after each track.

   =>    =>  

Tap the Edit sign, you can delete and change preset points, including the 1st home point.

2. Set Home Point in NVR Menu

If your camera is used with a NVR, you can also set the home point in NVR menu.

a) while viewing the camera on NVR screen, click the image of a camera, you will see a pop-out menu on bottom. Click PTZ control to enter PTZ menu.

b) In PTZ menu, use the joystick to move the camera to where you want. In preset type 1 and save. This point will be saved as preset #1.

c) Switch to Auto tracking menu, check Motion detection tracking and Home point, type 1 as the home point and Apply.

The camera will return to preset 1 after each tracking.

NOTE:

1. If your NVR does not have this Auto tracking menu, upgrade your NVR to latest version
2. If your NVR does not have this Auto tracking menu after the firmware upgrade, set the home point from mobile App.

How to replace my old NVR without pairing each camera again?

XMARTO’s long range WiFi security camera systems have been the best sellers on Amazon during 2015 – 2016.

Many customers’ security camera systems were runnning for 6-7 years, 24 hours per day, 7 days per week.

With that workload, some customers feel the necessity of replacing their old NVRs, or some of their old cameras.

Is there a way to swap the old NVR out without taking all cameras down for pairing? 

The answer is affirmative. 

As you may already know, the NVR itself is also a WiFi router.

The theory is simple: each time you replace your old WiFi router, you only need to set your new WiFi hotspot name and WiFi password exactly the same as before, your devices will automatically reconnect. Same thing for XMARTO NVRs.

Here are the steps replacing your old NVRs without re-pairing all cameras:

Step 1: Record the WiFi information of your old NVR. 

As showed in below image, in your old NVR’s menu, navigate to System Setting – Network setting – WiFi setting, you will see the ESSID and password information, which is the WiFi name and WiFi password of this NVR. Take a photo to record this information.

Step 2: Revise your new NVR WiFi information to the same as old NVR’s. 

Swap your old NVR out and plug your new NVR, enter the same WiFi setting. Revise the new NVR’s ESSID & password to exactly the same as on the old NVR.

Step 3: Find your cameras back

With the old WiFi information on the new NVR, your cameras are connected with the new NVR.

Now you need add the cameras to your NVR channels.

In the NVR menu, right click – Camera Manage; click Search till you see your cameras listed in the above box. Then click ‘Add One’ to add the cameras to NVR channels.

Your cameras will be added to the channels in the below box and work as before.

 

FAQ

1. My old NVR is still working fine. Should I upgrade it to a newer one?

Not necessarily. As long as they are working fine. You don’t have to upgrade the NVR, or the camera.

    2. I plan to add the latest XMARTO PTZ camera, or solar cameras to my old system. Is it compatible?

XMARTO products are compatible with each other. But if your NVR is 960p or 1080p, they are not capable to take in the new 3MP & 5MP cameras.

Please check your NVR’s version in System admin. If you have version 3.0+, you can feel free to add latest cameras. If your NVR version is earlier than 3.0, please consider to upgrade your NVR (hardware) to the latest model.

    3. What if my old NVR does not turn on and I cannot enter the menu?

Please try to open the old NVR, unplug the 2 cables on hard drive, see if you can enter the menu to record old WiFi information.

If you cannot enter the old NVR’s menu to find WiFi info, you will need to pair your cameras to the new NVR one by one. Here is how to,

https://support.xmarto.com/?sid=229823&lang=en&action=faq&cat=1&id=15&artlang=en

“Incorrect password” while viewing XMARTO cameras from App

The XMARTO home security systems have 2-layer of security password.

1. The NVR device password (AKA the admin password)

Each time you access the NVR menu, it requires the admin password. Without a device password, users will be locked out.

Device admin password can be set when you follow the 1st time initial setup, or at any time in System setting – System admin – User.

This is very important and we suggest you to set and remember your admin password at 1st time.

This device password (device lock) is local and it locks access to your NVR, no matter whether your NVR has Internet connection or not.

2. App login password

Like using any Internet service, using WallPixel App requires you to create an user account.

Your App user account is normally an email address or a phone number; and the password is the code protecting your user account.

If you don’t have a WallPixel App user account, tap Register to create an user account.

The App user account is different from your device admin password. They are 2 sets of combinations.

The NVR admin password is a local password locking your NVR; the App user account password is an Internet password locking access to your WallPixel user account.

3. The connection

The connection between App user account and the NVR/ camera is based on Cloud ID.

The Cloud ID is an unique ID number of a XMARTO NVR or camera. On most NVRs/ cameras, you can find a QR code indicating the device’s Cloud ID. You can also find the Cloud ID on NVR screen’s below right corner.

To access the Cloud ID corresponding device, you need to provide the device password. Without the password, you will be locked out.

As advised in the manual, when you add the NVR/ Camera to the App, you are lead to provide the admin password,

        

The password here refers to the NVR/ camera’s admin password, not the App user password.

Provide your admin password, you will be able to view the cameras remotely from the App.

If you are an authorized user by the administrator, provide your user name and your password.

4. Update device password

If you’ve changed your admin password lately, you need to update it to the App.

 =>   => 

A few important tips

1. The default password
   If you skip setting a password for your NVR or camera, then the default password is empty.
   You leave the password area empty and tap next to view the cameras or access the menu.

   That also means, theoretically anyone who knows your Cloud ID can access the NVR/ camera. (although no one will know your Cloud ID unless you show them). So it is strongly suggested to set an admin password; as soon as you start to use the XMARTO NVR/ camera.

 2. Secondary users

If you are running a store, an office etc; in the System setting – System admin – User setting, you can add a few users with secondary permissions.

Then give those secondary user accounts to your employees. For example, you added user “JohnWayne” with password “batman”.

When he try to access the NVR’s screen, he needs to change the username from “admin” to “JohnWayne”, then enter password “batman” to access the NVR menu.

Same thing in the App. Obviously John Wayne needs to create his own App user account with his own email or phone #.

Then when he add the NVR system or camera to App, he input or scan the Cloud ID, provide his own NVR/Camera access combination, to access the NVR/ camera, with your nominated permissions only.

3. That sounds way too complicated. “I’d simply let my families know my Cloud ID and admin password so they can view” 

Not suggested. Logically, the WallPixel Cloud will take the 1st App user who added the Cloud ID as the owner.

If you have a 2nd or 3rd user adding the same Cloud ID as admin, 1 or few of you may miss some features, such as the App notifications.

The correct way is to use the Sharing feature.

a) let your families download and install WallPixel App, then create his/ her own App user account.

b) in the App, tap sharing, set sharing perimissions and valid time. Then send the QR code to your families.

c) In WallPixel App, your families scan the QR codes to add the camera/ system.  (no matter where they are)

4. “My XMARTO security system have 4 cameras and a NVR. Does that mean I have 5 Cloud IDs?”
No, when you use a XMARTO camera system, the App only takes the whole system as a single device; so it recognize only the NVR’s Cloud ID; and let you view 4 to 10 cameras simultaneously in App, just like what you see on the NVR’s screen.

Privacy tips

1. Does XMARTO know my device admin password?
   No we don’t. The device password is a local password you set in the initial setup. We cannot know that.
   If you forgot the password, the only way is to hard reset it.
   About how to reset password, please contact support@xmarto.com
   The hard reset can be done only by yourself, with the hardware in hand.
2. Does XMARTO know my App user password?
   No we don’t. Any App attempts to collect user’s password will not be approved by App Store or Google Play.
   If you forgot the App user password, the only way is to tap “Forget password” and follow steps to reset password, or simply create another user account.
3. If someone hacks my App user account, what should I do?
   That never happened. But if you believe someone hacked your App user account, the 1st thing to do is tap “Forget password” in App to reset your user password; or contact support@xmarto.com to know how-to hard reset your device password. Any of the 2 password reset will lock the access immediately.

   For standalone cameras, please change the device password in device setting; or hold reset button to reset the camera and set it up again.
   For NVR or NVR systems, the way of hard resetting password is not public. Please contact support team with your order # to learn how to reset NVR admin password.

   Relax, it’s almost impossible to happen.

<p>The post XMARTO NVR WiFi PTZ Camera System FAQ first appeared on NVR IPCAMERA SECURITY.</p>

For version : 3.0.3.0 if it doesn’t notice the password is incorrect , pls make sure you used the wired mouse, due to 3.0.3.0 version doesn’t support wireless mouse.

Note:User name and password should not exceed 8 characters and should not contain such as &*! @ (… #% and other special characters

You can refer to our YouTube channel videos : https://youtu.be/KJpJnYFlGK8

1) Within the black area, Click the left mouse button>right mouse button>left click>right click… Lasts 6 times

 

2) Yes

 

3) Input your new password,The old password is empty,you don’t need enter anything.

HiSeeu Wireless Camera System installation guide

Read Next : Hisilicon IP Camera Firmware Update

 

4) OK

 

 5) If this step still not work, please email Johnny@hiseeu.com with below screenshot of your NVR, then they will send you the super password to login

 

How to solve the problem of camera connect failed?

Please follow these steps to troubleshoot

Please check if the white antenna on the camera is loose first.

1)Cover the sensor under lens on the camera to see if the light is lit or not.

If it’s bright, it means camera is not bad.

If it’s not lit,You can connect the power of a good camera to the bad camera.

 

In the case of determining that camera is not broken.

2）right-click the mouse> video manage> Refresh / Search

3) if your camera with reset button, no LAN port, please take camera close to your NVR

1. delete the connect failed channel

2. press the reset button on camera for 10 seconds

3.Right click the mouse again > wireless add > wait the screen show a new camera IP address 172.20.14.**

4. if no IP address, pls reset camera for several times,

After adding the camera successfully, you can exit the add camera interface

below is the video for you check :https://youtu.be/Kaxvth-sd-Y

4) if your camera with Lan port

Pls use an Ethernet cable connect the camera to your NVR.

Delete the connect failed Channel>Refresh(Search) find IP address 192.168.**.**>Match Code(wait for IP address change to 172.20.14.**)

After that you can unplug the Ethernet cable.

You can refer to this youtube video.

https://youtu.be/kmNnFgjLiPI

HDD not fund / Not record anything

 Please refer to these below to solve the HDD not fund issue.

1）Check the power adapter connected to the NVR box. The NVR box uses 12V 2A or 12V 3A power supply. If you connect the 12V 1A cameras’ power supply to the NVR, the NVR box will not provide enough power to drive the hard drive.

2) If hard drive is preinstalled, there are 4 screws at the bottom of NVR box.

3）Check Hard Drive Information on NVR box and Format it

Right click the mouse>system setup>General setup>HDD setup>select the hard disk>Click Format, if the progress bar always shows a few percent or the formatting is failed, please contact with us.

 

 

4) Please open the NVR with a screwdriver, check the two cables connecting the hard drive and see if they are loose.

 

5）Take the hard disk out and install it on your computer. Check if the computer can recognize the hard disk. This is to confrim the HDD is the problem or not.

How to solve Gateway Unreachable or Network Error

If you click “fast network” to appear: Gateway Unreachable or Network Error , pls fellow below steps:

Step 1:

1) you must check if the network line is faulty or not: check whether the switch and router line connection are correct.

2) Can you connect to the external network normally through the computer wired connection?

Notice: Do not directly connect the recorder to the fiber

 

Step 2: Right click mouse and choose Fast Network —-> Auto config ,check if the network will be healthy or not

 

Step 3: If the auto config still can’t make it work , pls kindly check the same network computer network setting

Then “manual configuration” set the recorder network settings, don’t choose DHCP, input the same IP address and gateway and submask same as your computer

Offline

1)Pls Connect NVR to your router with an Ethernet cable. After that right click the mouse > Fast network.

 

2)If Step 1 doesn’t work, Maybe the Ethernet cable is damaged. Please replace it with a new one

3)If there is no problem with the cable.

Pls right click the mouse> system setup >Network setup>Do not choose DHCP>Change DNS to 114.114.114.114 or 8.8.8.8 > Power off the NVR and power on again(Reboot the NVR)

4)You can also connect the NVR to your home WiFi,

Enter the wireless internet interface > Select your home WiFi and enter your password > Apply

Change the display channel of the camera

When you select the corresponding channel, you can click the two buttons on the left, and then move the channel

You can also drag the image directly to another channel

How to set up Motion Detection？

1)Enable Motion Detectin on NVR Monitor

Pls right click the mouse>system setup>Channel Setup>Video detection>Selecting the Channel for Motion Detection>Choose the form of alarm>After you set it up you can Click “Copy to” to set to all channel

 

2) Set the area of motion detection to be set within the field of view of the camera.

 

3)App Alarm

a)Select App Alarm on NVR

b)Click three dot> Alarm push

 

c)Click System authority settings, turn on all permission of the app.

 

How can I view the camera remotely?

There are four methods to view the camera system remotely. Please refer to these step below.

 

1) First you need to connect the NVR with your router by wired or WiFi

Wired connection

1. wired connection, connect the NVR with router by ethernet cable

2. right click your NVR mouse choose fast network, then click auto config, check cloud ID status is online and network is healthy, then you can remotely check the system on your phone app

3. if not online and healthy network, please click manual configure, and check your router detail,

make sure the NVR and your router is the same IP gateway, IP address the first 3 number should be the same, the last one can’t be the same ,. preferred DNS please change to 8.8.8.8 and apply it

WiFi connection

1. please notes our NVR only can work with 2.4Ghz wifi network,

2. right click your NVR mouse choose system setup–network setup–wireless internet –enable wireless LAN, then find your house wifi name, input password, apply it

（please note the wifi name can not included any special character ,such as “_”, otherwise it will show connected failed.）

3. check the status is connect failed or success, if it is failed, please click view details,

check the same wifi network details on your phone and your NVR, then change them to the same IP gateway, IP address the first 3 number should be the same, the last one can’t be the same ,. preferred DNS please change to 8.8.8.8 and apply it

https://www.hiseeu.com/a/help/article/27632

2）To view on the Phone

a) Setup NVR box

Please reset your password：right click mouse>system setup>system admin>user>setuppassword>change a new password(Password must be within 8 characters)

b) Setup Mobile Phone

Scan below code download “Eseecloud”

 

 

c) Click “+”–“other way to add/scan the QR code on your NVR fast network page “–input cloud ID user name is admin and password is the one you login in NVR (If you doesn’t change the user name and password, User Name is admin password is the one you set for the NVR before), if your forget the password please refer this step: https://www.hiseeu.com/a/help/article/27650

(Cloud ID is in the lower right corner of the screen or right click your NVR mouse and choose fast network to find Cloud ID)

 

 

Scan the QR code on display

 

The user name is admin, enter the password of your camera system in the password field

 

3）To view via Eseecloud software on PC

EseeCloud for Windows PC

Eseecloud MAC: http://download.dvr163.com/tool/EseeCloud-mac-2.0.8_20200228.zip

Eseecloud Windows: http://download.dvr163.com/tool/eseecloud/EseeCloud_Setup_3.0.7.10.exe

here is the video to check how to add it : https://youtu.be/0AX1-sMKJG4

If you have registered your eseecloud account on your mobile phone, you can directly log in with your eseecloud account on the computer, and the account information will be automatically synchronized to the PC software

 

Double Click Cloud ID

 

How to remove the red triangle mark

For the red triangle mark it is for notice you something happened for your camera

such as the motion detection , video loss, HDD not found,

for remove the triangle

1. you need upgrade your NVR version to 3.0.5.0

there are 2 ways to upgrade

1) online upgrade, connect the NVR with router by LAN cable , right click your NVR mouse and choose system setup–system admin–system upgrade–online upgrade

2) offline upgrade, you need copy the firmware to the USB disk and choose local upgrade the firmware you cane email Johnny@hiseeu.com to get it

3) after you upgrade successfully, pls right click your NVR mouse and choose system setup–general setup–error setup–disable alarm icon.

Connect the camera to WiFi, then add it to NVR

You can connect the camera to your home wif and then add it to NVR.

First you need to press the reset button for 6s on the camera to reset the camera,

1) Please refer to pages 4 to 6 of the manual in the attachment to connect the camera directly to your mobile app,

 

 

 

 

２）First, you need to connect NVR to your router,

Then search the NVR for the camera connected to WiFi

Right Click the mouse > Video manage > Change the “protocol” to “onvif” > Search > Add one

 

if it show Password Error, please go to your phone app , click “…”–“Edit” then on blank place quickly click 6 time you will see cameras password here, go back to NVR video manage page, select the correct channel, click Manual Edit to input camera password .

What to do when the screen color is not displayed correctly

1） Click the mouse to select the screen –> click the 3rd icon (color adjust)

2) Click Default button–>select Ircut mode–>Ok

If it doesn’t solve your problem ,pls send this screenshot to us

Audio function！

1:Please check if there is a microphone hole on the back of the camera.

 

 

2:When you want to use the audio function of the camera, you need to turn on the audio function of the camera:(left click your mouse on the camera images)

3: right click your mouse — turn up the volume

4: Also turn on the audio button on App

 

 

if your version is 3.0 ,you should choose the AV stream also,refer these step

right-click the mouse ->System Setup->Channel Setup ->Encode Setup ->Select orresponding Channel(1-8) ->change the Encode Mode to AV Stream -> Apply

 

5: Every camera supports audio, but you can only use the audio of one camera at the same time.

and if the NVR your had order is with monitor, pls plug in your headphones or stereos behind the NVR

 

Why can’t remotely check the playback and change the setting

pls fellow below step

right click your mouse and choose system setup –system admin–user–edit user– choose remote and config and playback

How to solve the problem of camera lost connect with NVR, need reboot the camera to fix this problem?

Firmware 1: https://www.dropbox.com/s/qlyr53xfsrjscox/%E9%87%8D%E5%90%AF%E7%9B%B8%E6%9C%BA%E5%9B%BA%E4%BB%B6.rar?dl=0

 

IPCAKV3W_20220415_3_6_82_572011

IPCAKV3W_20220415_3_6_82_572011

(Fix the camera lost connection with NVR need unplug camera power cable)

Firmware 2: https://www.dropbox.com/s/mrdzs1ioqhmuuve/%E4%B9%9D%E5%AE%89%E5%8D%95%E6%9C%BA%E4%BF%A1%E5%8F%B7%E4%BC%98%E5%8C%96%E5%9B%BA%E4%BB%B6.rar?dl=0

 

IPCAKV3C_20220415_3_6_82_572010

IPCAKV3W_20220415_3_6_82_572011

(Fix camera signal problem)

 

572010 for the camera model: 5322-W

572011 for the camera model: 5323-W

please go to video manage page to confirm the camera model.

 

To upgrade the camera firmware: download the firmware from the dropbox, unzip the file at first, copy the correct file to your USB DISK root, format should be FAT32,go to system setup–channel setup—IPC upgrade page–click the correct channel–click start–remove mouse –insert USB disk–wait for camera upgrade successfully

I’ve connected everything, but the display doesn’t show images

Pls Refer to the following steps

1）Press the left mouse button for 30 seconds and the camera system will reboot.

2）A)You need use a VGA cable to connect the NVR to the monitor.

B)If you don’t have a VGA cable but have another monitor, you can connect the camera system to another monitor.

3）Then change the output resolution of NVR.(Right click the mouse>system setup>General setup>Screen setup>Output resolution)

Set an appropriate resolution and switch back to the original HDMI Cable.

4）If the display is still not displayed, you can choose another resolution.

if your NVR box version is 3.03.0 pls change the step 2 as below：

2) Then change the output resolution of NVR.(Right click the mouse>system setup>General setup>Display Resolution)

If camera often loses signal with NVR？

You can use the following four methods to solve the problem of poor camera signal

Please check if the white antenna on the camera is loose first.

1)First, you can change the wireless channel of the camera system to ‘other’, and the antenna of NVR is better to stand up

Right click > system setup > Network setup > change Wireless channel to “other” > Apply

Then restart the NVR, unplug the power supply of the NVR and plug it in again

2）You can replace the white antenna on the camera with the black extension antenna in the package, so that the black extension antenna passes through the wall.

 

Place the camera next to the NVR to ensure that there is a good signal between the camera and the NVR.

3）You can set a camera as a WiFi repeater to enhance the signal between the camera and the NVR.

4）You can also buy a WIFI repeater, which also enhances the signal between the camera and the NVR.

for Wifi repeater you can search: B07NRBYM5C on amazon.

If you can write a good rating to our camera system,We can send you one for no charge.

(warm notes:if your version is 3.0,there is “Search”button but not “refresh” ,click the “search” but the “refresh”)

(version 3.0)

How to use the wifi repeater to enhance signal

 

When the repeater is powered on, its indicator lights up.

Press the reset key for 10 seconds and it will deletes all previous matching records

How to use it on NVR.

1)Connect the repeater to NVR by Ethernet cable

2)click “Search” and then there will disappare a device which IP address is “192.xx.xx.xx”

Click it, it will pop up a new window

click Match button to let the status become “wireless has been matched”

 

At this point, you can unplug the Ethernet cable.

4) back to the Video Manage interface and click the Repeater .it will show the same window as the figure below.

click the add icon after the Router button,then select chanal which you want to enhance sigal

How to add an extra camera?

when you receive the new camera , there is no match between the nvr box and the new camera. You need to pair them.

if your camera with reset botton , no Ethernet port,

1)right click your NVR mouse and choose wireless add

2)press the camera reset botton for 10 seconds

3)wait it shows camera IP address 172.20.14.**

4)if no IP address, pls reset camera for several times, then you can exit,

below is the video for you check

https://youtu.be/Kaxvth-sd-Y

 

if your camera with Ethernet port, You can refer to our video on Youtube.

https://youtu.be/kmNnFgjLiPI

1) You need to connect the camera and the NVR box with the Ethernet cable.

2)Right-clik the mouse video manage→Refresh/search( find camera IP address as 192.168.1.**)→Match code( wait camera IP address changed to 172.20.14.**) then exit and choose add one

After camera and NVR are paired, you can unplug the Ethernet Cable.

3) Use the same way to pair more camera.

How to solve “Resolution too big”?

Our system upgraded , the “Resolution too big” camera is 3MP, old system can’t work with 3MP camera

1. right click your NVR mouse choose system admin–system version to check NVR version is 2.8 version or 3.0 version

2. if it is 3.0 version, you can upgrade it to latest firmware then it can support 3MP cameras (3.0.6.0 version and above version)

how to upgrade to NVR?

1) Online upgrade : go to system admin-system upgrade-then click online upgrade, wait for it upgrade successfully, then camera will show image

2) Offline upgrade, please email Johnny@hiseeu.com with your system version page , then she can provide firmware to you

3. if it is 2.8 version,the only way can fix is to upgrade camera firmware

right click your NVR mouse–system setup–system admin–IPC maintance, then take a screenshot of camera version, email : johnny@hiseeu.com for resolution too big problem.

4. after you get the firmware, please copy to your USB DISK root, format should be FAT32,go to IPC maintance page–click the correct channel–click start–remove mouse –insert USB disk–wait for camera upgrade successfully

5. go to system setup–channel setup–encode setup–find correct channel–change resolution from 2304*1296 to 1920*1080.

How to Change the Display Position of Channel

There are 2 ways to changed the position of camera

 

1)Generally speaking, we will choose four channels to display at the same time on the screen

 

For convenience, let’s first choose to have all channels displayed on the screen.

right click your mouse — Split Screen — X8 View

 

Now we want to let the Channel 7 to the Channel 2 position

left click the mouse on the channel 7 screen and dont loose

then move to the channel 2 position ,loose the mouse left key

 

that is OK

2)Please wrote down the IP address of the camera (which you want to exchange it channel,such as channel 5). Then deleted the channel which you want that camera to place(such as channel 2), did a manual edit on channel 2 ,Enable it and change or add the IP address of channel 5 wrote down. Camera immediately came up on channel 2.

App wrong Password

Pls refer to these step to solve the wrong password issue. refer this video : http://youtu.be/bFVwGqnr2Js

1)If you doesn’t change the User Name and the Password on NVR box.

The User name is ‘admin’, no password (you needn’t input anything)

 

 

 

2)For change the password on NVR box.

Right click the mouse>system setup> system admin>User>set password

 

3)User name and password should not exceed 8 characters and should not contain such as &*! @ (… #% and other special characters (you can setup password: jasmi985/ jasmi996/ jasmi856 or others. )

If you can login NVR with a password, but can’t login on App, please confirm that the password within 8 characters

Note：App login username and password are different from the camera login username and password. They are two different sets of username and password system.

How to set up Email notification?

a. Enable POP/IMAP in your email. If default setting of your E-mail enables that, please skip this step.

Login your email via browsers; go to Settings – Forwarding and POP/IMAP-Enable POP and IMAP – Save Changes.

 

We also need to Allow 2-Step Verification for your Gmail account, login www.google.com

 

• Open your Google Account.
• Select Security.
• Under “Signing in to Google,” select 2-Step Verification and then Get started.
• Follow the on-screen steps.
• Normally after you set 2-step verification, you will create a new password on NVR password page you need input this password

b. Go to your system main menu. System setting- Channel setting- Video Detection. Enable E-mail Notification and click Copy to apply the same setting to other channels.

 

b. Go to your system main menu. System setting- Network setting- Email setting. You will see the interface shown below.

 

c. Follow the instruction below to input the information required to finish the setting.

 

Email Notificaion: Check “Enable”

SMPT Provider: Click the one you use in the selection. Or click USER CUSTOMIZE to use the E-mail server that is not in the selection.

Sender : Type in your sender email address

Password: the password of login your sender emial address

SMTP service: when you choose the correct SMTP provider, it will suggest correct service to you

Port: The default port is 25. If it doesn’t work, you can go to the link below to get the port of the e-mail you use.

https://www.arclab.com/en/kb/e … .html

Encryption Type: Select the one that your E-mail server works. If there is no selection, please choose None.

Sendee 1: the email you want to receive email alerts

Sendee 2: the second email you want to receive email alerts, you can leave it blank

 

d. Then click Test see if you can receive a test e-mail alerts from Esee. If yes, that means the setting has set successfully. Then, please click Apply to save the setting.

e. Latest APP allow to set email notification on the cellphone directly

Go to cellphoen app Eseecloud, click me–settings–mail to receive alert messages–enable it, then put your gmail address, to get verfication code, after you input verfication code click confirm, then you will get the email notification, thanks

 

 

 

 

 

How to setup Record Plan?

You can set up three modes of record plan

Note：After you have set up the record plan, you need to click “copy to” to apply the record plan to all channels.

1) Time Recording:

Setup period of time of recording on NVR,Right Click the mouse>System Setup>Record Setup>Record Plan.

Click Time and put mouse icon on the upper left corner(for example 1 as picture shows).press and drag the mouse to the right to choose the time.the list will turn to red.

2) Motion Recording:

Only detect motion and then start recording. Right click mouse>System Setup>Record Setup>Record Plan.

Click Motion and putr mouse icon on the upper left corner, press and drag the mouse to the right to choose the time. The list will turn to green.

3) Alarm Recording:

Riht click the mouse>System setup>Record Setup>Record Plan.

Click Alarm and put mouse icon on the upper left corner,Press and drag the mouse to the choose the time,The list will turn to yellow.

Note: Users can Setup any period of time they want, for example 0:00:00-23:59:59, That’s 24hrs*7days recording. When NVR detects hard disk, the default setting will be 24hrs*7days recording.

The priority of Alarm is higher than that of Motion, and the priority of Motion is higher than that of Time.

When you have set the corresponding record mode, you can click “select all”, and the time area below will become the corresponding color

Video Playback

Right clik the mouse>Video Playback>Choose date、Channel、record mode>Click Search>then can view playback file

Note：You can only watch four Channels recording at the same time.

1. IIIustration for playback button:

play,

pause:

fast forward*2,*4,*8；

2. Play file: Choose the recording file in file list,as number“1”shown in picture. Chooseone of the recording, click“play”to play to recording file;

3. Video backup: Choose the recording file in file list,as number“1”shown inpicture.insert the U flash disk, click“video backup”to backup the file;

4. Timeline: Click“date”and“time”at left bottom to check the timeline of recording, as number“2”shown in picture;

5. On the timeline with recording file,left click the mouse, the can playbackthe file.

How to watch the playback on my phone?

First ,you should install the Eseecloud on your phone ，if you hadn’t installed it ,refer this link:

http://www.hiseeu.com/news/wirelessskitfaq/69.html

click playback

then it will show the interface follow below

choose the time and channel which you want to watch

Notes: The default is no sound when you watch playback.so you should click this sound button to open it if you want to hear

How to backup the recording

There are 2 ways to make backup

1) use USB disk to backup

1. right click your mouse, and choose video backup.

2. choose the channel/date/time playback you need backup,

(If you copy too much backup, we suggest you copy it one by one channel to save copy time)

3.Backup, the let your mouse out and within 30 seconds put the USB to get the backup

if you need check tbe playback you copy out on computer, pls use VLC player , you can download here :

http://download.dvr163.com/tool/Video-player%20.zip

 

pls notes USB disk format should be FAT32 otherwise your NVR may can’t find it.

 

2) make backup on computer

 

1. download Eseecloud :

Eseecloud MAC: http://download.dvr163.com/tool/EseeCloud-mac-2.0.8_20200228.zip

Eseecloud Windows: http://download.dvr163.com/tool/eseecloud/EseeCloud_Setup_3.0.7.10.exe

 

2. add the system to your Eseecloud phone account, then on computer software choose login cloud(login with the phone app Eseecloud account and password)

 

3. search the cameras playback, and choose the channel you want to make playback and wait for it shows the recording

 

4. click the download icon the chose the files you want to download, wait for it finished the process, then you can open the it and check the playback on computer

 

here is the video for you check : https://youtu.be/kR7QN_2UKdI

Factory Setting

Pls refer to these step below to reset system

1)Right click the mouse>System setup>System admin>factory setting

*Note: pls don’t check “Channel setup”&”Screen setup”&”Digital Channel”

Click “Apply”

2)If you Check “All”

After NVR Reboot,you need Right click again>video manage>Double-click the IP address of camera (like 172.20.14.2)

If Your NVR box version is 3.0.3.0

Pls refer to below steps

Right click the mouse>System setup>System admin>factory setting>simple restore

The standalone camera connection step

pls connect it step by step , if you fail , pls send us some screenshot and tell us which step is wrong by email or whatsApp

our email is :johnny@hiseeu.com

Wechat/WhatsApp:+86 13392810296

Skype:Johnny.chen1204

1) download “Eseecloud” app on your phone and register it

click add button and choose Standalone camera

 

2)check if the camera light lit

click this button

3) Point the camera of the mobile phone at the QR code of the camera

4）Choose a network environment for your camera, the WiFi name

5）input the wifi password and click the connecting device button

6) Wait a minute and it will connect succeed click COMPLETE button

7)edit the camera name and set its password(password can be empty )

that is finished! if you want change some camera information such as password, you can click setup button to set it

Here is video for you check how to connect it on phone app : https://youtu.be/tNKeWUfe-mI

How to fix there is no cloud ID

1. Connect the recorder to the same LAN as the computer ：connect to the router

2. Provide the IP address of the recorder, System Settings – Network Setup Photo

 

 

3. Recorder switching debugging mode: system setting – system management – system maintenance, right mouse click, pop-up dialog box, click the left mouse button in the blank space of this pop-up dialog box, right click, click the left and right button, 12 times, Find out if the font prompt toggles the debug version, click Yes, OK. Go back to the lower left corner of the main interface with a red font. Take a photo to us (2.8 version)

 4. Provide remote tool ID and password, manufacturer technology remote connection control and send the email to us

if you don’t have the remotely tool, you can send the email to us, so we can send to you

(3.0.3.0 version)

3.Recorder switching debugging mode: right click your mouse—system setup–general setup–time setup–change the Date format–right click your mouse, pop-up dialog box ,

click the left mouse button in the blank space of this pop-up dialog box, right click, click the left and right button, 12 times, Find out if the font prompt toggles the debug version, click Yes, OK. Go back to the lower left corner of the main interface with a red font. Take a photo to us.

How to contact amazon customer service?

1). Use your Amazon account to log into www.amazon.com

2).Pull down to the bottom of this page and find “Help” button , and click on it to get into a new page

3). Find “Need more help ” in the middle of this page and move it to this button and you will see “Contact Us ” and click on it .Then you will get in touch with Amazon Customer Service Associate.

4).Or you may choose to call the Customer-Service by number 866-216-1072

Add Device (412 camera system)

First you need to connect the camera system to your WiFi.

Click the home button.

 

 

Select your WiFi and enter wifi password

This string of numbers is cloud ID.

Then go to “Eseecloud” app

Networked devices

Input your cloud ID and User name(User name is admin) and password(Camera system has no password by default)

5MP WK-4HB315-1T TZ-HB315 Night Vision is not good,upgrade as below

Please download the firmware at this link :

https://www.dropbox.com/s/gcrg3xw7f42ylys/IPCAKV5C_20221011_3_6_97_572110hsy%281%29.rom?dl=0

After you get the firmware, please copy to your USB DISK root, format should be FAT32,

Pls right click your NVR mouse–System Setup–Channel Setup–IPC Upgrade–Select the correct channel–click start–remove mouse –insert USB disk–wait for camera upgrade successfully

How to solve Most of Network Status Problem?

Please right click NVR mouse choose Fast Network check Network Status

• Healthy network: Network connect successfully
• Gateway Unreachable: means NVR IP Gateway and IP address not in the same gateway as your router, Click Manual Config, then find your router correct IP gateway, such as 192.168.1.1, then IP address should be 192.168.1.***, last numbercan’t be the same as your router, change it on NVR. If you connect with wifi network, you need go to System Setup—Network Setup—Wireless Internet page click View Details and click Manually to change those information.
• Request DNS Error: disable DHCP, change the Preferred DNS to 8.8.8.8, reboot the NVR and router.
• Network Cable Disconnect: make sure the NVR connect with router by Ethernet cable
• Network Card Not Found: on Network Setup page find PPPoE disable it.
• Network Busy: disable DHCP, change the Preferred DNS to 8.8.8.8, reboot the NVR and router.

<p>The post HiSeeu Wireless Camera System installation guide first appeared on NVR IPCAMERA SECURITY.</p>