ACH20-1B Thermal Monocular Camera: Using the App

Take some time to learn about using your thermal monocular camera through the companion Thermal Connection app.

Live View Settings

The Live View is the first screen you will see when your camera connects to the app. It includes the following features:

Digital Zoom

Zoom in on a certain part of your camera’s image to magnify details.

1.From Live View, tap .

2.Tap your preferred zoom range.

3.Tap OK to save.

Color Palette

Select your camera’s color palette for enhanced visual representations of thermal imaging.

1.From Live View, tap .

2.Tap on one of the following color palettes:

Note: Not all color palettes are suited for every situation. Select the option that best shows the thermal differences for your specific application.

Record Images & Videos

1.From Live View, tap .

2.Tap the screen to display the capture and record icons.

3.To capture images: Tap .

4.To start or stop recording videos: Tap .

Note: A blinking red dot next to a recording timer on the left of the screen indicates that your camera’s recording.

Function Settings

Enable some of your camera’s features, like the laser pointer, fire detection, or track hot and cold points.

Laser Pointer

Use the laser pointer to illuminate a point of interest with a bright spot of colored light.

 LASER RADIATION:

Exposure to laser light can cause significant damage to the eyes. Never look into the laser beam directly or through a piece of optical equipment.

After a few seconds, the laser pointer automatically turns off.

Fire Detection

Detect fires in your camera’s image with a red box surrounding the source. If enabled, you can set the fire detection sensitivity from high to low.

Hot & Cold Points

Track the hottest and lowest temperatures in your camera’s image at the same time. If enabled, your camera’s image will display a red target tracking the hottest point and a blue target tracking the lowest point.

System Settings

Customize your camera’s system settings or sign out.

Automatic Sleep Mode

Select how long your camera waits before entering sleep mode.

Automatic Shutdown

Select how long your camera waits before turning off.

Change Measurement Unit (Meter to Feet)

Change your camera’s measurement unit.

Sign Out

Disconnect your camera from the app by signing out of the app.

Restore to Default Settings

Restore your camera’s menu and app settings to its factory default settings.

ACH20-1B Thermal Monocular Camera: Troubleshooting

The following article provides some troubleshooting tips for using your thermal monocular camera.

.

Camera’s image/screen is blurry.

Adjust your camera’s diopter to your eyesight. Before you begin, it is highly recommended that you adjust your camera’s diopter to your eyesight. Focusing your view will minimize eye strain and fatigue.

Camera’s Wi-Fi hotspot is not showing.

• Wait a moment for it to appear in your phone’s Wi-Fi settings.

• When enabling your camera’s hotspot in your camera’s settings, try to press  a couple more times.

• Ensure you have allowed the app to use your location, otherwise it will not be able to detect your camera’s Wi-Fi. Navigate to your phone’s settings, then open the Thermal Connection app settings, and enable Location — While Using the App.

Camera is not connecting to the app.

The Wi-Fi password is case sensitive. Make sure you enter the serial number in the same letter format, whether that is uppercase or lowercase.

Camera has disconnected from the app.

Camera’s Live View is frozen in the app.

If the Live View is frozen perform a hard close of the app, then open it again.

Digital zoom is not working.

Digital zoom will not work while your camera’s menu is open. Press  to exit the menu.

Camera is not recording images and videos.

Recording images and/or videos will not work while the menu is open or when your camera is connected to a computer. Press  to exit the menu.

Camera’s screen is black.

Restart your camera. Press and hold  to turn your camera off, and then back on.

Camera is not charging or slow to charge.

• Ensure you use the supplied micro-USB cable and that it is properly connected.
 DANGER

◦ Improper battery replacement or use may result in fire, explosion, or other hazards.

◦ Only use accessories regulated by the manufacturer. Never use the charging cable or power adapter with another product.

◦ Make sure the plug is properly connected to the power socket.

◦ DO NOT charge your camera within 2 m of flammable materials.

◦ DO NOT connect multiple devices to one power adapter. The plug in the power socket could overheat and possibly cause a fire.

• Ensure the USB Mode is set to Off.

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to USB Mode.

◦ Press  to open the setting.

◦ Press  to select Off.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

Camera’s battery keeps draining.

You can preserve your camera’s battery life in the following ways:

• Turn off any camera settings or functions that are not being used.

• Use your camera without the app. First, sign out your camera from the app, and then turn the Wi-Fi hotspot off. 

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to WiFi.

◦ Press  to open the setting.

◦ Press  to select Off.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

• Set your camera to go into automatic sleep mode after 1 minute of inactivity has passed. First set your camera’s sleep mode (Suspend Mode) to be automatic, and then set the automatic sleep mode (Auto Suspend) to 1 minute.

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to Suspend Mode.

◦ Press  to open the setting.

◦ Press  to select Automatic.

◦ Press  to confirm your setting.

◦ Press  to navigate to Auto Suspend.

◦ Press  to open the setting.

◦ Press  to select 1 Min.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

• Set your camera’s screen brightness to low.

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to Brightness.

◦ Press  to open the setting.

◦ Press  to select Low.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

• Set your camera’s automatic shutdown to 60 minutes or less. 

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to Auto Shutdown.

◦ Press  to open the setting.

◦ Press  to select 60 Mins or less.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

Camera’s image has lots of graininess or scratches.

• Turn your camera off, attach the lens cap, and allow it to rest for a few hours before using again.

• To improve your camera’s image quality set the FFC Mode to Auto. 

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to FFC.

◦ Press  to open the setting.

◦ Press  to select Auto.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

• To manually correct pixel defects in your camera’s image, set the DPC settings to Manual. 

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to DPC.

◦ Press  to open the setting.

◦ Press  to select one of the options:

· Auto: (Default) Your camera automatically calibrates defective pixels.

· Press  to start auto DPC.

· Close the lens cap until your camera signals that auto correction is complete.

· Manual: Correct the defective pixels manually.

· Press  to start DPC manually.

·  Press to switch between the X-axis and Y-axis.

· Press and hold  or  to start correction.

· Restore: DPC is restored to original state.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

ACH20-1B Thermal Monocular Camera: Frequently Asked Questions

The following FAQ answers many of the general questions about your thermal monocular camera.

.

How does my thermal monocular camera work?

To improve the visibility of objects in complete darkness, haze, or tough conditions, your thermal monocular camera uses infrared sensors to detect heat given off by a person, animal, or other objects. It creates images of that radiation called thermograms, which display the relative temperatures of different objects with different shades or colors. In a thermogram, warm objects stand out in a contrast or often cooler background. It is widely used in outdoor scenarios for hunting, rescue, animal observation, and more.

Is my thermal monocular camera battery-operated or hard wired?

Your thermal monocular camera is battery-operated, however, to charge the battery you will need to connect the micro-USB cable into your camera’s USB port and the other end into a power source.

Does my thermal camera only work at night?

No. Although thermal imaging cameras are most commonly used for nighttime vision, they can also be useful in daylight. The detection of heat radiation and the high contrast of thermal imaging cameras allow you to see the outlines of (warm-blooded) animals that camouflage well in their environments. It can also help distinguish animals or people in foggy or smoky conditions.

Can my thermal camera see-through walls, metal, or glass?

No, thermal imaging cameras do not see-through surface but detect surface temperatures.

Is thermal imaging and night vision the same thing?

No, thermal imaging can produce pictures without visible light while night vision cameras work by boosting ambient light. Their only common purpose is increasing visibility in low light conditions.

Can bright sunlight damage my camera’s lens?

Yes, aiming your camera’s lens with the lens cap open at powerful light sources (i.e. the sun) is not recommended, as this may adversely affect the accuracy or damage the thermal imager.

What is the clicking noise my camera makes?

This is simply the noise your camera makes while you are shifting it between different fields of view. The noise you are hearing is your camera focusing and calibrating the image to achieve the highest resolution possible.

Should I charge my camera’s battery before first use?

Since your camera’s battery is delivered partially charged, it is recommended that you fully charge it before first use.

How do I charge my camera’s battery?

Your camera has the following 4 battery charging statuses, as shown by the LED charging indicator located under the USB port.

How do I turn my camera on or off?

Press and hold .

Where can I find the mobile app?

The Thermal Connection Application can be downloaded on your smartphone with a valid Internet connection from iTunes or Google Play respectively.

See the article Connecting to the App for more details.

Why do I need to allow my Location Permission on the app?

The app requires permission to detect your Wi-Fi network in order to connect your camera to the app.

How do I connect my camera to the app?

See the article Connecting to the App for full details.

How do I disconnect my camera from the app?

For steps on disconnecting your camera from the app, see the article Using the App.

What is my camera’s Wi-Fi name and password?

Where can I find my camera’s serial number?

Your camera’s serial number can be found on:

• The serial tag located on the side of your camera.

• Your camera’s system information.

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to (System Information).

◦ Press  to open your camera’s system information.

How do I record images & videos?

• To capture images: Press 

• To start or stop recording videos: Press and hold  for 3 seconds. A blinking red dot next to a recording timer on the left of the screen indicates that your camera is recording.

Note: Your camera cannot record images or videos while the menu is open or when connected to a computer.

For steps on recording images and videos from the app, see the article Using the App.

How do I zoom in my camera’s image?

To switch the zoom range: Press . Keep pressing to zoom in and out.

For steps on using digital zoom from the app, see the article Using the App.

How do I turn the laser pointer on?

 LASER RADIATION:

Exposure to laser light can cause significant damage to the eyes. Never look into the laser beam directly or through a piece of optical equipment.

To turn the laser on: Quickly press  two times.

For steps on using the laser pointer from the app, see the article Using the App.

How do I change my camera’s color palette?

To quickly change the color palette: Press .

For steps on switching the color palette from the app, see the article Using the App.

Which color palettes can I choose from?

Select your camera’s color palette for enhanced visual representations of thermal imaging. Switch between any of the following color palettes:

Note: Not all color palettes are suited for every situation. Select the option that best shows the thermal differences for your specific application.

How do I measure my target’s distance?

Measure the range distance between your camera and your target using the pre-set ranging modes for animals, people, etc.

• Press and hold  to open the menu.

• Press  or  to navigate to Ranging Mode.

• Press  to open the setting.

• Press  to select one of the options:

◦ Wolf: Measure your distance from a wolf, with a pre-set height of 1.2 m.

◦ Customize: Enter a custom height to measure your distance from your target.

◦ Wild Boar: Measure your distance from a boar, with a pre-set height of 0.9 m.

◦ Human: Measure your distance from a human, with a pre-set height of 1.8 m.

◦ Rabbit: Measure your distance from a rabbit, with a pre-set height of 0.3 m.

• Press  to confirm your setting.

• Press  to exit the menu.

How do I change my camera’s measurement unit?

For steps on changing the measurement unit from the app, see the article Using the App.

How do I track hot & cold points?

Track the hottest and lowest temperatures in your camera’s image at the same time. If enabled, your camera’s image will display a red target tracking the hottest point and a blue target tracking the lowest point.

• Press and hold  to open the menu.

• Press  or  to navigate to Hot Point.

• Press  to open the setting.

• Press  to select one of the options:

◦ Off: Hot and cold points is turned off.

◦ On: Your camera will track hot and cold points.

• Press  to confirm your setting.

• Press  to exit the menu.

For steps on enabling hot & cold points from the app, see the article Using the App.

How do I enable fire detection?

Detect fires in your camera’s image with a red box surrounding the source. If enabled, you can set the fire detection sensitivity from high to low.

• Press and hold  to open the menu.

• Press  or  to navigate to Fire Warning.

• Press  to open the setting.

• Press  to select one of the options:

◦ Off: Fire detection is turned off.

◦ High, Middle, or Low: Your camera will detect fires based on the sensitivity level.

• Press  to confirm your setting.

• Press  to exit the menu.

For steps on setting fire detection from the app, see the article Using the App.

How do I enable the fire detection alarm?

Set your camera to sound an alarm when fire is detected in the image.

Note: The fire detection alarm works only when your camera has fire detection enabled on either High, Middle, or Low.

• Press and hold  to open the menu.

• Press  or  to navigate to Alarm.

• Press  to open the setting.

• Press  to select one of the options:

◦ Off: Fire detection alarm is turned off.

◦ On: Your camera will sound when fire is detected.

• Press  to confirm your setting.

• Press  to exit the menu.

How do I export recordings?

Export recorded images and videos from your camera’s microSD card.

• Press and hold  to open the menu.

• Press  or  to navigate to USB Mode.

• Press  to open the setting.

• Press  to select Mass Storage.

• Press  to confirm your setting.

• Connect the micro-USB cable into your camera’s USB port and the other end into an available USB port on your computer.

• The microSD card’s storage will open on your computer desktop. Select files to export, then copy them onto your computer.

• After exporting, disconnect the micro-USB cable from your camera and computer.

• Press  to select USB Mode Off.

• Press  to confirm your setting.

• Press  to exit the menu.

Where does my camera store recorded images and videos?

Your camera stores recorded images and videos onto the microSD card.

What is my camera’s maximum storage capacity?

You can insert a microSD card with up to 256GB storage space.

How do I hide the icons on the top right of my camera’s image?

• Press and hold  to open the menu.

• Press  or  to navigate to Status Bar.

• Press  to open the setting.

• Press  to select Off.

• Press  to confirm your setting.

• Press  to exit the menu.

How do I change the language displayed in my camera’s menu?

• Press and hold  to open the menu.

• Press  or  to navigate to Language.

• Press  to open the setting.

• Press  to select your preferred language.

• Press  to confirm your setting.

• Press  to exit the menu.

Note: This will only change the language in your camera’s menu, not the app.

How do I restore my camera’s settings to default?

For steps on restoring your camera’s settings to default from the app, see the article Using the App.

How do I update my camera?

Update your camera through the microSD card.

Note: To download the latest firmware update for your camera, contact the Technical Support team.

• Press and hold  to open the menu.

• Press  or  to navigate to USB Mode.

• Press  to open the setting.

• Press  to select Mass Storage.

• Press  to confirm your setting.

• Connect the micro-USB cable into your camera’s USB port and the other end into an available USB port on your computer.

• The microSD card’s storage will open on your computer desktop. Copy the update program to the microSD card.

• Press and hold  and  at the same time for 3 seconds. A blue screen will indicate that an update is in progress.

After a few minutes the update will complete and you will see your camera’s live view image.

Where can I download my camera’s latest firmware update?

To download the latest firmware update for your camera, contact the Technical Support team.

Can I mount my camera to a tripod?

Yes, the tripod thread can be found on the bottom of your camera.

Can I access my camera’s Live View from an external monitor?

Yes, you can access your camera’s Live View from your computer by connecting your camera using the micro-USB cable.

What is the buzzer option in the app settings?

The buzzer is not compatible with your camera.

ACH20-1B Thermal Monocular Camera: Connecting to the App

Follow the steps below to connect your thermal monocular camera to the Thermal Connection app.

Note: The frequency bands and transmitting power (radiated and/or conducted) nominal limits applicable to this radio equipment are as follows: Wi-Fi 2.4 GHz (2.4 GHz to 2.4835 GHz) 20 dBm.

.

Step 1 – Download the App

Download your camera’s mobile app, Thermal Connection.

.

Step 2 – Enable Your Camera’s Wi-Fi Hotspot

Looking into your camera:

• Press and hold  to open the menu.

• Press  or  to navigate to WiFi.

• Press  to open the setting.

• Press  to select AP (Access Point).

• Press  to confirm your setting.

• Press  the exit the menu.

Step 3 – Connect to the App

You will now be able to view your camera from the app and make some minor setting adjustments.

.

<p>The post Thermal Monocular Camera user manual first appeared on NVR IPCAMERA SECURITY.</p>

ATTENTION: Prior to purchasing and installing an accessory antenna, read the product specifications of your receiver to determine if your receiver has a weatherproof housing. Installing your weatherproof receiver outdoors provides a better line-of-sight between the receiver and the camera, increasing the strength of the wireless signal. See your product specifications to determine the weatherproof rating of your receiver.

The Directional Wireless Panel Antenna and the Omni-Directional Antenna are used to extend the range of one or multiple wireless or wire-free cameras.

Directional Wireless Panel Antenna (ACCANTD9)

Omni-Directional Antenna (ACCANTO8)

Use the 2.4GHz Directional Wireless Panel Antenna (ACCANTD9) to focus a wireless signal onto one specific wireless device (camera or receiver) to increase the range of transmission. A clear line-of-sight between the antenna and the wireless device needing range extension is required.

Use the 2.4GHz Omni-Directional Antenna (ACCANTO8) to enhance the signal of one or multiple cameras that are paired to a single or dual antenna receiver. You may also use two Omni-Directional Antennas to extend the range of all cameras paired to a dual antenna receiver.

REQUIREMENT: To connect the antenna directly to the camera or receiver, the device must have a removable SMA type antenna. Visit www.lorextechnology.com/compatibility to ensure the antenna is compatible with your camera or receiver model.

Lorex Wireless Cameras and Monitors guide 2024

Also Read  : Lorex Camera Troubleshooting

Recommended Antenna Installation Methods

Your antenna needs will vary depending on the setup of your camera system, the number of cameras that require range extension, and the number of channels on your wireless receiver. Review the scenarios below to ensure you have the correct antenna and installation method to meet your needs.

Click a setup scenario to see the recommended installation method:

Combining Accessory Antennas

If you have installed your accessory antenna according to the recommended installation methods and would like to enhance wireless signal strength even further, you may add an additional Directional Wireless Panel Antenna (ACCANTD9) directly to a camera. The additional Directional Wireless Panel Antenna can be used with a Directional Wireless Panel Antenna or with an Omni-Directional Antenna attached to the receiver.

Click an antenna combination to see recommended installation methods:

Scenario 1: Extend the range of one camera paired to a single antenna receiver

To extend the range of one camera connected to a single channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9).

The Directional Wireless Panel Antenna can be connected in two configurations.

Configuration 1. Connect the antenna directly to the camera

Configuration 2. Connect the antenna directly to the wireless receiver

REQUIREMENT: The antenna connects using an SMA cable and replaces the existing antenna on either the camera or wireless receiver. Check www.lorextechnology.com/compatibility to determine if your product is compatible with the antennas.

Scenario 2: Extend the range of one camera paired to a dual antenna receiver

To extend the range of one camera connected to a multi-channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9). Connect the Directional Wireless Panel Antenna directly to the camera.

Scenario 3: Extend the range of select cameras paired to a dual antenna receiver

To extend the range of select cameras on a multi-channel receiver, use the Omni-Directional Antenna (ACCANTO8).

Connect the Omni-Directional Antenna to one of the antenna ports on the wireless receiver.

REMINDER: Each antenna port on a dual antenna receiver is associated with specific camera channels. One antenna communicates with odd numbered channels (1, 3, and 5), while the other antenna communicates with even numbered channels (2, 4, and 6). See the table below for dual antenna channel configurations.

If you connect the Omni-Directional Antenna to an antenna port and your wireless signal does not improve, try switching the Omni-Directional Antenna to the other antenna port or pairing your camera to a different camera channel.

Scenario 4: Extend the range of all cameras paired to a dual antenna receiver

To extend the range of all cameras on a dual antenna receiver, connect an Omni-Directional Antenna (ACCANTO8) to each antenna port on the receiver.

IMPORTANT: Two Omni-Directional Antennas are required to accommodate this setup.

Combination 1: Combine two Directional Wireless Panel Antennas

If you are using a Directional Wireless Panel Antenna (ACCANTD9) to enhance the signal of a single camera with a single channel receiver, you can use an additional Directional Wireless Panel Antenna to further enhance the wireless signal.

Connect one Directional Wireless Panel Antenna directly to the camera and one Directional Wireless Panel Antenna directly to the wireless receiver. To maximize signal strength, it is recommended to aim the two antennas directly at each other with a clear line-of-sight.

Combination 2: Combine a Directional Wireless Panel Antenna with an Omni-Directional Antenna

If you are using an Omni-Directional Antenna (ACCANTO8) to enhance the signal of multiple cameras, you can further enhance the signal of a specific camera by connecting a Directional Wireless Panel Antenna (ACCANTD9) directly to the camera.

A clear line-of-sight between the Directional Wireless Panel Antenna and the Omni-Directional Antenna is recommended to maximize signal strength.

Lorex SD Pro App: Changing / resetting the password

If the password for the Lorex SD Pro app to view the Wireless Home Monitor is lost or forgotten it will need to be reset.

To reset the Lorex SD Pro app password:

1.Ensure that your Wireless Home Monitor is connected to a network router using the included Ethernet cable.

2.On the Wireless Home Monitor tap the Menu icon ().

3.Use the joystick to select Settings > Network > Reset Password.

4.Select Yes to confirm.

5.Tap the Menu icon () repeatedly until all the menus are closed.

6.Launch the SD Pro app and enter the default password. Refer to your user manual for your default password. You will be prompted to create a new password.

Lorex SD Pro App: Setting up Wireless Home Monitor remote access

You can access and view wireless cameras from a Wireless Home Monitor system using an iPhone, iPad, or Android smartphone or tablet using the Lorex SD Pro app. It is available at the App Store or Google Play Store.

Prerequisites:

To set up the mobile application:

LW2700 Wireless Home Monitor: Included cables and accessories

LW2700 Series Wireless Home Monitors support wireless cameras using a wireless signal. They do not have an internal battery and require a connection to a power source. Refer to your user manual for model specific information on cables and accessories. Click here for downloads and documentation for your product.

Most wireless home monitors include the following cable connections and accessories when purchased:

Network: Wireless camera Internet requirements

Standard wireless cameras that connect to a DVR / NVR, do not need access to the Internet to function. Stand-alone IP cameras do not require an Internet connection for basic functions, but an Internet connection is required for full functionality.

Security Cameras: Understanding Field of View (FOV)

Field of View (FOV) is the maximum observable area that is seen at any given moment through an optical device such as a camera lens. The coverage of the area can be measured using the horizontal and vertical distances to find the diagonal of the area in degrees. Mathematically, the FOV is calculated using the horizontal dimension of the sensor (h) and the Focal Length (F).

You can find the camera’s Field of View details in the Specifications sheet. Click here for additional support content including security camera documentation.

The Camera Lens, Sensor and Focal Length

Focal length (F) is the distance between the center of a lens and its sensor. The size of the lens is the aperture size.

These factors affect field of view. A narrower focal length captures more of the scene and displays a larger field of view. A wider focal length magnifies a scene and decreases the field of view. The higher the focal length value the lower the FOV.

Types of Camera Lenses

Fixed: a fixed camera focal length provides an Angular FOV which is permanently set and cannot be adjusted by the user. Varifocal: the camera focal length can be manually adjusted by the user. Generally, this is done manually with screws or dials. At Lorex we have motorized varifocal cameras that allow you to digitally zoom using your phone or NVR without losing details. These lenses provide flexibility and customization for your camera image needs.

The importance of Field of View

A wide angle lens or smaller lenses produce a greater field of view and captures more objects in a scene enhancing your ability to cover larger and wider areas such as foyers, parking lots or warehouses.

A narrow angle lens or larger lenses produce a smaller field of view; capturing a limited area, but the camera quality image improves in detail. These are designed to monitor a specific object, such as cash registers, entrances/exits, hallways or objects of value.

How to Calculate the FOV

To calculate the FOV requires the sensor size and the focal length of the lens: h = Sensor Size F = Focal Length of the Lens

FOV is represented by this equation: FOV = 2tan-1(h) / 2F

Example: h = 4.7mm F = 6mm FOV = 2tan-1(h) / 2F = 2tan-1(4.7)(12) = 2tan-1(0.39) = 2(21.4°) = 42.8°

W482CAD – 2K Wi-Fi Camera : Frequently Asked Questions

The following FAQ article answers many of the general questions about the 2K Wi-Fi Camera with Smart Deterrence (W482CAD). Where applicable, the FAQ includes links to articles where you may find more information.

.

Where do I place my Lorex 2K Wi-Fi Camera?

.

How should I position my Lorex 2K Wi-Fi camera?

When mounting the camera on a wall, make sure of the following:

 Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

.

How do I enable motion detection and person detection?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap  icon to enable Motion Detection.

Note: If motion detection is disabled, general/person/vehicle detection will automatically disable and you will not receive any motion detection notifications in the Lorex App.

.

How do I customize Motion Zones™?

Motion Zones™ allows you to customize your device’s motion detection region. Motion Zones™ screen consists of the following settings:

To set Motion Zones™

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap Motion Zones™.

 For full instructions on how to set customized Motion Zones™, see Configuring Motion Zones™.

.

Why am I receiving so many notifications?

There are a few ways you can lower the number of notifications you are getting.

.

How do I enable Color Night Vision?

1.Lauch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap  icon to disable Auto Night Vision.
Note: Disabling Auto Night Vision will force the camera into Color Night Vision mode. Recommended in low-light conditions.

.

How to activate Two-Step Verification?

1.Launch the Lorex App.

2.Tap Settings.

3.Tap Account Settings.

4.Tap Two-Step Verification.

5.Tapicon to enable Two-Step Verification.

For detailed setup instructions, see Two-Step Verification Setup.

.

How to optimize video quality?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Video Settings.

4.Tap  icon to enable HDR (High Dynamic Range).

Note: Enabling HDR optimizes video picture in high-contrast conditions such as under-lit and over-lit areas.
By default, the video quality is set to High (2x1080p HD).

.

What is Home & Away™?

Lorex App can automatically use your location to manage your notifications when you are at home or away. The app will notify you when you are inside/outside of your set home perimeter.

To start using this feature, navigate to your mobile device settings and enable Location services for Lorex App.

For detailed setup instructions, see Configuring Home & Away™.

.

How do I activate the LED deterrence light when motion is detected?

1.Lauch Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Deterrence Light Brightness.

4.Tap  icon to enable camera’s deterrence light whenever motion or person is detected.

.

How do I remove the 2K Wi-Fi Camera from my account?

1.Launch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Remove Device.

.

How to permanently delete data of 2K Wi-Fi Camera?

Refer to Formatting Device Storage for more information.

.

Does my device support WPA2 or WPA3?

Your device supports Wi-Fi Protected Access 2 (WPA2) which is the industry standard security protocol for Wi-Fi networks. WPA2 offers security against unauthorized access and data interception and is supported by most Wi-Fi routers including those that support both WPA2 and WPA3. It employs Advanced Encryption Standard (AES), an encryption mechanism, which secures communication between your camera and Wi-Fi network to keep transmitted data confidential. For information on which devices support WPA2 and which devices support WPA3, please refer to “WPA2 and WPA3 Supportive Devices.”

.

What are the compatible SD cards?

Refer to Compatible SD Cards and Storage Sizes for more information.

.

What devices are compatible with the 2K Wi-Fi camera?

Refer to Product Compatibility Chart for more information.

W482CAD – 2K Wi-Fi Camera : Installation

This article provides instructions to install your Lorex 2K Wi-Fi camera with Smart Deterrence (W482CAD).

.

What is included in the box?

The above contents are based on one camera.

.

How to connect with Lorex App

3.Open the Lorex App app and create an account or login with your credentials.

4.Tap  icon to add a new device, then follow the in-app instructions to complete the device setup.

For full instructions on Lorex App setup, see Connecting with Lorex App.

.

How to mount 2K Wi-Fi Camera to the wall

.

How to mount 2K Wi-Fi Camera to the ceiling

Wi-Fi Security Cameras – How to Read a MicroSD card

To view the contents of a MicroSD card on a laptop or computer, follow these steps:

a. Select the day to play back:

b. Click on the available folder:

c. Within the folder, click either the day folder (Video files) or the jpg folder (Snapshots):

d. Click to select a video time from 00 – 23 hours:

6.Click the MP4 video file to view the video. 

Wireless Home Monitor: Audio not working

If the audio is not working on your Wireless Home Monitor:

• Ensure that the protective film is removed from the camera lens.

• Ensure that the monitor volume is not muted. A mute icon () will be visible on the screen if the volume has been muted.

• Turn the monitor volume up using the volume buttons on the side of the unit. Location will vary by model. For exact location of volume buttons for your model, refer to your user manual. Click here for downloads and documentation for your product.

• The camera must be in Full Screen mode for audio. Tap the Channel Select icon () to switch between channels in Full Screen mode. Audio is disabled in Quad mode.

If audio is not working after increasing the volume and viewing in Full Screen mode, restore the system to default settings.

To restore your monitor to default settings:

CAUTION: Restoring to default settings will erase any setting input on the monitor. Your monitor will need to be reconfigured.

1.On the monitor tap the Menu icon ().

2.Use the joystick to select Settings > Default Settings.

3.Select Yes.

.

<p>The post Lorex Wireless Cameras and Monitors guide 2024 first appeared on NVR IPCAMERA SECURITY.</p>

.

Getting Started: Enabling the VIVOCloud service in your device

Before starting using your VIVOCloud application, you must enable the VIVOCloud service in your devices. This guide will teach you how to enable the service in easy to follow steps:

Step 1. Log in to your NVR device using its username and password.

Step 2. Click on the gear icon to access the NVR configurations.

Step 3. In the Settings interface, select the System tab and click on “VIVOCloud service”.

Step 4. In the VIVOCloud service interface, you will see a “blue” button (old interface) or a “gray” button (new interface). Clicking this button will enable the VIVOCloud service on your NVR.

After clicking it, the NVR will start connecting to the VIVOCloud server and register the service (this might take 1-2 minutes depending on your internet connection). Once the connection is established and the device is registered in the cloud system, a QR code and Device ID will be displayed below.

Note: If you are using the local console, follow the same steps, as both the Local and Web interfaces are the same in this regard.

Now the device service is enabled and you should be able to add it to your VIVOCloud application. 

VIVOCloud setup and use guide

Read Also : Vivotek Vortex Camera Ultimate Guide

.

Getting Started: Adding your NVR to the VIVOCloud application using the QR code/device ID

In order to add your VIVOCloud compatible device, you need to use a QR code or Device ID. This document will explain where to find this information:

Enabling the Service:

Before being able to add your device using its QR code or Device ID, you need to ensure that the VIVOCloud service is enabled. First, log in to your NVR device using its username and password.

Once you have accessed the device, click on the gear icon to access the NVR configurations.

In the Settings interface, select the System tab and click on “VIVOCloud service”.

In the VIVOCloud service interface, you will see a “blue” button (old interface) or a “gray” button (new interface). Clicking this button will enable the VIVOCloud service on your NVR.

After clicking it, the NVR will start connecting to the VIVOCloud server and register the service (this might take 1-2 minutes depending on your internet connection). Once the connection is established and the device is registered in the cloud system, a QR code and Device ID will be displayed below.

If you are using the local console, follow the same steps, as both the Local and Web interfaces are the same in this regard.

Adding the device to the VIVOCloud application:

In the VIVOCloud application, go to the configuration menu and select “Add devices” to add your NVR. Then, click on the “Add devices manually” section. Here, you will be allowed to choose between using a QR code or the device ID.

Using the Device ID

Type the Pcode/Device ID found on the NVR VIVOCloud service webpage and click on the “+” button to add the NVR to the VIVOCloud application.

Using the QR Code

Click on the QR button to scan the QR code on the webpage using your phone camera (make sure to allow the application access to the camera).

Once finished, you will be able to see your NVR cameras in the VIVOCloud application. 

[VIVOCloud Camera] How to generate the QR code/PCode in a VIVOCloud compatible camera?

Question

How to generate the QR code/PCode in a VIVOCloud compatible camera?

Answer

VIVOCloud devices are not limited to just NVRs; cameras that support remote connection using VIVOCloud are also available. The principle of using a QR code/Device ID is the same as with the NVR. For clarity, follow these steps to obtain the QR code/PCode of the camera and add it to the VIVOCloud application:

Step 1. Access the camera web interface using its IP.

Step 2. Go to the camera configuration by clicking on the “Configuration” tab.

Step 3. Click “Applications” > “Package management” > “VIVOCloud” and click the link of the VIVOCloud VADP page.

Step 4. Click the “Connect” button to generate a unique QR code/Device ID which will be used to add the device into the VIVOCloud application.

For security purposes, the QR code and Device ID will only be available for 5 minutes so please be sure to have your phone at hand to fastly add the device into the application. 

If you are unfamiliar with the QR code scan process or Device ID registration, please refer to the following documentation:

[VIVOCloud Application] How to share your device with other account?

Question 

How to share your device with other account?

Answer

Devices configured in your VIVOCloud account can be shared to other users (e.g family members, coworkers, etc.). To share devices please follow the next steps:

Step 1. Login into your VIVOCloud phone application.

Step 2. Click on the option icon to access the application account configuration menu.

Step 3. Once the menu has appeared, click on the “Share devices” button to start the sharing process.

Step 4. In the “Share devices” interface, click on the “SHARE YOUR DEVICES” button to start registering the email of the user you want to share the devices with.  

Step 5.  Type the email address (user with VIVOCloud account) which will be accessing your device and click the “NEXT” button to continue.

Step 6. All of your configured devices will be listed. Select the devices to share by checking them, click “Done” when finished. 

Once the device is ready to share you will see a green arrow notification.

Step 7. Click on the “Share” button to share the device to the configured email account. 

Important note: You can only share the same device with up to 4 accounts. 

.

[VIOVCloud]How to share the usage data with VIVOTEK

Question

How to share the usage data with VIVOTEK

Answer

For VIVOVloud app, please follow the steps to check.

1. Go to your account from setting.

2. Go to Privacy policy.

3.Make sure the analysis and data are shared.

For VIVOCloud portal, please follow the steps to check.

1.Go to your account.

2. Go to Privacy policy.

3. Make sure the analysis and data are shared.

4. Please reload the website after seeing complete message,

[VIVOCloud/iViewer] [2.4.401/3.10.604] Why the live image is being cut for 4 equal when viewing MS9390-HV?

Question

MS9390-HV is two wide angle lens. When I view the MS9390-HV live image on VIVOCloud/iViewer, it is being cut for 4 equal.

If I login the WEB page of MS9390-HV, it is working normal. How to solve it?

Answer

We will solve this issue in VIVOCloud 2.5.1 and iViewer 3.11.1.

How to remove NVR from VIVOCloud app and portal?

QUESTION

How to remove NVR from VIVOCloud app and portal?

ANSWER

How to use VIVOCloud to connect to NVR if the NVR is already added to other VIVOCloud account?

QUESTION

How to use VIVOCloud to connect to NVR if the NVR is already added to other VIVOCloud account?

ANSWER

[VIVOCloud] Do you need to purchase a license to use the VIVOCloud service?

Question

Do you need to purchase a license to use the VIVOCloud service?

Answer

No license is required to use the VIVOCloud service with VIVOCloud-compatible devices. For more information on compatible devices, please visit the following link:

[VIVOCloud Application] What is the maximum number of notifications that can be stored in the application?

Question

What is the maximum number of notifications that can be stored in the application?

Answer

The VIVOCloud application can show push notifications in the phone which will allow you to easily see alarm and device status (disconnection). 

You can also see all the notifications that have been sent to the application from the NVR/Camera in the notification menu, but there is a limit on how many alarms can be stored. The application can store a maximum of 100 notifications, if the application receives a new notification when this number is exceed, the old alarms will be deleted and replaced with the new ones.  

.

[VIVOCloud] What ports are used by the VIVOCloud Service?

Question

What ports are used by the VIVOCloud Service? 

Answer

The VIVOCloud Service uses below ports:

If your network firewall or router only allows connections to specific ports, please ensure that the ports listed above are not blocked from inside to outside; otherwise, this could cause issues when the NVR/Camera tries to connect to the VIVOCloud server. Below is a list of possible situations you might encounter if the ports are not properly opened.

Situation 1. Cannot enable the VIVOCloud service in the NVR

If port 1194 is not opened, the VIVOCloud service on the NVR will display an yellow ‘!’ icon.

Situation 2. Portal connection issues with NVR

If the port 3478 is not opened, VIVOCloud portal will show the device as “Connecting”.

Situation 3. Slow video connection

If the other ports are not opened, you may not see an image on VIVOCloud, or the image may load slowly.

Ensuring that the necessary ports are not blocked by your network’s firewall or router is crucial for establishing a successful connection between your NVR/Camera and the VIVOCloud server. By following the guidelines above and verifying that these specific ports are accessible, you can facilitate a smooth and efficient operation of your VIVOCloud devices.

[VIVOCloud] What can I do if I cannot access my NVR device through the VIVOCloud portal or mobile application?

Question

What can I do if I cannot access my NVR device through the VIVOCloud portal or mobile application?

Answer

VIVOCloud service allows you to remotely access your NVR/Camera videos remotely using the browser or application without the need opening ports or performing extra configurations. If you encounter any issues while using this service please be sure to check the following:

1. Check that you are using a compatible browser:

If you are trying to access the VIVOCloud webportal (service.vivocloud.com), be sure to use the Firefox browser. 

The VIVOCloud portal is only supported by this browser, if you use other browser you wont be able to access your NVR videos. You can find more information about browser compatibility in the VIVOCloud official webpage: https://www.vivotek.com/vivocloud#portal

2. Check that the VIVOCloud service is enabled

Before using the VIVOCloud service you need to enable it, in order to do so please go to your ND device configuration, under System > VIVOCloud service and be sure that the service is enabled. There should be a green mark next to the blue button, if you don’t see this mark you might need to click on the button to enable the service.

VIVOCloud service enabled:

VIVOCloud service disabled:

3. Check that the ND device was only added to one account:

Each ND device can only be registered to one VIVOCloud account, if you already added to another account and try it to add it into a new account you will find the following error:

If you want to delete the NVR from any other accounts because you want to add it to a new account you just need to disable the service in the configuration page and re-enable it, this will automatically remove the device from the original account. Please note that if the device was previously shared to another account it will also be removed. 

4. Network and configuration check

The VIVOCloud service server is very strict with its data management so you need to be sure that everything is properly configured otherwise you might not be able to enable the function on the ND. Before enable the service please be sure to verify the following: 

a) Time zone needs to match your access point time zone: 

b) ND IP must be properly configured and the device internal network access point needs to have access to WAN.

c) Be sure that your NVR is up to date and is using the latest firmware available

If you don’t know how to upgrade the device, feel free to check this documentation: 

d) Be sure that the service main ports are accessible, if the main ports used for server communication are being blocked you wont be able to add the device to your VIVOCloud account. Here is a document that explains in detail which ports are used by the service. 

If after following all the suggestions mentioned in this guide you are still unable to access your device using the VIVOCloud service please contact Technical Support for assistance. 

.

<p>The post VIVOCloud setup and use guide first appeared on NVR IPCAMERA SECURITY.</p>

Overview; This article provides the most common causes for issues related to playing or downloading a UniFi Video Troubleshooting recording. Please check each section carefully and compare it with your setup before moving on to the next section.

Camera Recording Mode not Configured

Back to Top

In UniFi Video, cameras must first be configured to either Always Record or Record Only Motion mode before recordings will be generated. You can view the recording mode in the Camera page of UniFi Video.

To change the recording mode:

1. Log in to the UniFi Video Controller and go to the Cameras section.
2. Open a camera’s Properties pane by clicking on the camera.
3. Click on the Recording tab.
4. Under the Configuration section, in the Record Mode dropdown, choose either Always Record or Record Only Motion, then click Save.

If Schedules are in use, verify the Schedule configuration is appropriate. You may also need to verify that the time zone is set correctly under Settings > Time & Date, and that the NVR has sufficient internet access to be able to update its time via NTP.

Inadequate Motion Sensitivity Settings

Back to Top

If Record Only Motion is selected, make sure that the Motion Sensitivity settings are configured in a manner adequate for the scene that is being monitored. To configure Motion Sensitivity:

1. Log in to the UniFi Video Controller and go to the Cameras section.
2. Open a camera’s Properties pane by clicking on the camera.
3. Click on the Recording tab.
4. Under the Motion Detection section (click to expand), click the Configure button in the Zones section.
5. In the Window that appears, verify that the motion detection zone covers the area you wish to monitor, and increase Sensitivity as needed until motion events are triggered reliably.

Remember to use the Test Zone functionality to test your settings, then click the Save button to store the changes.

Incorrect Recording Path

Back to Top

If the recording path is not set to a valid directory, UniFi Video will fail to store recordings. While the interface will validate that the path is correct during configuration, it is possible that the path may be incorrect after a configuration is restored from backup, or the filesystem has been changed at the OS level.

Verify that the recording path is correct under Settings > System Configuration > Recording Path.

User Tip:Remember that paths on Linux-based NVRs are case sensitive.

For reference, the default recording paths are:

• Windows Custom Installs: C:\ProgramData\unifi-video\data\videos
• Linux Custom Installs: /usr/lib/unifi-video/data/videos
• UVC-NVR / UVC-NVR-2TB: /srv/unifi-video/videos

Recording Path has Incorrect Permissions (Linux-Based NVRs)

On Linux-based NVRs, the unifi-video user and group must be correctly assigned to the target recording directory so that UniFi Video can store recordings. The user and group can be unexpectedly changed while mounting an external device, browsing the structure using software, or making configuration changes.

To correct the permissions, SSH into the NVR and issue the following commands to re-assign all permissions correctly. Be sure to change the path as necessary to reflect your environment. The chown command may take a significant amount of time depending on the number of recordings in storage.

sudo service unifi-video stop
sudo chown -R unifi-video:unifi-video /srv/unifi-video/videos
sudo service unifi-video start

In certain cases—particularly when using network attached storage, the permissions or ownership of the root directory of the mounted storage may change. To avoid this, create a subfolder to use as a recording target and assign the appropriate permissions.

External Storage Device is Not Mounted

If external storage is used as the recording target, such as an external hard drive connected via USB or a NAS appliance, it is possible that the device has unexpectedly become unmounted. In some cases, the storage may not successfully mount after the NVR is rebooted, or the device may become unavailable during operation due to a disconnect, network issue, or configuration change.

Access the storage path on the NVR via SSH or Windows Explorer as applicable, and verify that the expected storage size is available and the storage is correctly mounted with appropriate permissions. In certain scenarios it is possible that UniFi Video may be writing to the local mount path while the storage device is unmounted, effectively consuming storage on the root or C:\ drive and interfering with the mount process.

NOTE:Please note that external storage is outside of our official support scope. If you require further assistance with external storage, please consult our Community Forums.

System is in Emergency Shutdown State

If the available free space in the target recording directory is less than the Space to Keep Free setting, UniFi Video will enter Emergency Shutdown mode to maintain stability. In this mode, no new recordings will be stored to disk. Emergency Shutdown mode will be indicated as a log entry in server.log. To troubleshoot this issue:

1. Verify the video storage paths, as detailed above.
2. Verify that the Space to Keep Free storage retention settings are configured appropriately considering the size and configuration of your storage. Go to Settings > click the System Configuration button > Configure tab > Space to Keep Free and modify the slider accordingly. The UVC-NVR / UVC-NVR-2TB use a default setting of 10GB and 40GB respectfully.
3. Perform a Database Analysis, with Restore Recordings enabled. This feature can be accessed from Settings > System Configuration > Tools. Be sure to check Restore Recordings, then click Analyze. This is particularly important after restoring a configuration backup in order to import old recordings so they can be added to the purge rotation to free space.

If the Emergency Shutdown state persists, review the server.log and purge.log file for further entries that may describe the cause.

RAMDisk is Not Configured Correctly (Windows NVR)

If UniFi Video is unable to store inbound video segments to the temporary cache, recordings will not be processed. Verify that the RAMDisk has been correctly configured, is mounted with sufficient space (minimum 3GB), and that the path has been properly set in system.properties.

For more detailed information on the use of a Windows RAMDisk, see: UniFi Video – Using a RAMDisk as a UniFi Video Temporary Directory in Windows

Database is Inconsistent or Corrupt

In certain scenarios, a database that has inconsistent data may impede the NVR’s ability to process recordings. If all prior options have been exhausted, a database reset will restore the data and structure without losing vital configuration or prior recordings.

UniFi Video – Troubleshooting Cloud Connections

Overview

This article includes the most common issues that arise with UniFi Video connections done over the cloud. Cloud connections with UniFi Video are those done via https://video.ui.com/.

NVR Doesn’t Appear When Accessing Via Cloud

After logging in to https://video.ui.com, a prompt to Select NVR with a list of NVR options should appear. If an NVR is missing from that list, follow these steps:

NOTE:This only applies if for NVRs that have previously been adopted to Ubiquiti Cloud. Otherwise the appropriate step would be to click on Set Up New NVR.

Solution Steps

1. Log in to your UVC-NVR locally via its IP address. If you don’t know what the IP address of the NVR is, find it using the Ubiquiti Discovery Tool (Download Chrome App).
2. Verify that you are logged in with the email address of the Super Admin as seen in the Users section of the UniFi Video Controller.
3. Check to make sure the NVR is still adopted via the NVR UI in Settings.

Cannot Connect to NVR Via Cloud

After the NVR has been successfully adopted via video.ui.com, if the NVR is inaccessible via Cloud, determine the NVR has a red or green status icon in video.ui.com. The red or green status indicates whether or not the NVR is connected to the Ubiquiti cloud. Many times, even an NVR with a red (disconnected) status could still be fully functional, aside from the loss of Cloud access.

Solution Steps

Red Status. This means that your NVR is not reaching out to Cloud. Follow these steps to troubleshoot:

• Check the UI Status page to see if there is any issue on our side.
• Verify that the name of the NVR as shown in the UniFi Video Controller’s Settings matches how it appears in video.ui.com.
• If the NVR in question was restored from another UVC-NVR, it should be re-adopted. To do so, select the NVR that is inaccessible and click “Remove selected NVR”. Then proceed to re-adopt the NVR to the Cloud.
• Use this guide for best networking practices: UniFi-Video – Ports Used.

Green Status.

If your NVR has a green status, but you still cannot connect to your NVR, that means the the NVR is connected to Ubiquiti Cloud, but the device being used and the NVR can’t reach each other. See this guide for best networking practices: UniFi-Video – Ports Used to fix this issue.

Issues Adopting NVR to Cloud

Solution Steps

1. Make sure that all outbound Ports from the NVR are open and available, as per UniFi-Video – Ports Used.
2. This functionality makes use of some special features of ES6. It is recommended to use Google Chrome for best results.
3. Try clearing the browser cache and try an incognito window as well. Some browser extensions may interfere with this functionality.

UniFi Video – Troubleshooting Camera Disconnects

Overview

This article provides several possibilities to test when facing a camera that will disconnect for no apparent reason.

Introduction

UniFi Video cameras may disconnect from the NVR for a variety of reasons. Identifying whether the behavior affects specific cameras or all of them, whether the disconnects follow a pattern (such as disconnecting during sunset), or simply remain disconnected, will help identify the root cause of the issue.

Most importantly, consider if the camera disconnections warrant troubleshooting in the first place. Often camera disconnects can be triggered by changes made to the network, such as disconnecting a cable, restarting a switch, changing configurations, or even a power outage. Comparing the timestamp of the disconnect with the events and alerts from your UniFi Controller or network hardware may reveal the cause.

For cases where further investigation is required, this article discusses the common causes for camera disconnects.

Faulty Cable Infrastructure

Faulty wired infrastructure may cause unpredictable behavior, including camera disconnects or random reboots. Even though a camera may initially establish a network connection when first installed, a damaged or unreliable signal path can present problems that don’t become apparent until external factors such as interference, vibration, temperature fluctuations or further wear and tear affect the cabling.

The easiest way to quickly rule out wired infrastructure faults is to remove the camera from it’s installed location, and connect it using a short, known-good patch cable to the same switch that the NVR is connected. If the problem is resolved, then the issue is either related to the network hardware between your NVR and cameras (network switches, wireless links, etc), power related (as discussed below), or network cable related.

Problems caused by faulty network cabling are often seen in conjunction with:

• Long cable runs (exceeding the 100 meter maximum)
• Poor quality or damaged cable
• Faulty or incorrect RJ45 terminations
• Not using outdoor rated STP cable when appropriate
• ESD damage, due to improper grounding / shielding

Inadequate Power Supply

UniFi Cameras require a stable power supply in order to operate reliably. If the camera does not receive enough power, the camera may behave erratically causing disconnects.

A common symptom of a camera that doesn’t receive adequate power is when the device disconnects around sunset, as the camera will switch to night mode thus enabling the IR LEDs which more than double the power draw. Additionally, if a single power source is supplying multiple devices simultaneously, one or more devices may not boot properly after a cold start such as a power outage.

The power draw requirement for each camera model is documented in the product Data Sheet, which is downloadable in our Downloads page or at the bottom of each model’s page when navigating from our products page. Keep in mind that the cabling and associated infrastructure between the power source and the camera will generate resistance increasing the amount of power used and should be factored into the total wattage required from the power source. The length and quality of cable, quality of terminations, and additional in-line connections such as a patch panel should be considered.

To test if inadequate power is the root cause of camera disconnects, uninstall the camera from its mounting location and connect it to a suitable power supply such as a PoE switch or PoE injector using a short, known-good patch cable. Cover the light sensor typically located on the front of the camera in order to trigger a switch to night mode and turn on the IR LEDs or leave it overnight to go through a full 24 hour cycle.

If powering multiple devices off a PoE-IN switch such as a NanoSwitch, factor in the power draw of all connected devices, the power consumption of the switch itself, and estimate loss from cabling infrastructure. A NanoSwitch will typically require at least a 24V 1A PoE injector in order to power more than one camera or a camera and an airMAX radio.

If powering the cameras using a PoE switch, verify that the connected devices are not exceeding the total power budget available from the switch. A PoE switch should generally not be operated near its maximum power rating, as headroom should be allowed for the increased draw during startup.

If powering a camera using a PoE injector or an Instant 802.3af adapter, verify that the injector and adapter are adequate for the camera, and if necessary test using a different known-good injector or adapter. Instant 802.3af adapters in particular may work best if installed on the camera-side of the network cable, rather than at the switch.

Cabling infrastructure problems may also be a source of power related symptoms, and the troubleshooting steps from the previous section should be followed.

Unreliable Wireless Connection

If the camera is connected to the network via a wireless connection, as would be the case of a  G3-Micro, or when using external hardware like an airMAX radio as a client, verify that the wireless connection is stable enough to sustain the connection.

To help determine if the wireless connection is the cause for your disconnects, consider moving the camera or client radio within a few feet of the access point (AP). If the connection stabilizes, then the wireless connection needs to be addressed. Even if the connectivity issue persists, the wireless connection should still be investigated.

Factors that may cause frequent wireless disconnects include:

• Low wireless signal (SNR), as read either by the AP or the client (or camera)
• High interference (noise) caused by external sources, such as non-802.11 networks, machinery or appliances
• High wireless channel saturation, caused by high client density or nearby networks on the same channel

To improve the wireless connection, you can:

• Move the camera or the AP closer to each other, in order to reduce the distance and improve the wireless signal.
• Move the camera or the AP away from sources of interference, such as microwaves or cordless phone bases.
• Change the wireless network channel to one with lower utilization and fewer networks. You can use Ubiquiti’s WiFiman mobile application (available for iOS and Android) to identify channels with less networks, or UniFi’s built-in RF Environment scan.
• Install an additional AP closer to the camera on a separate channel, in order to reduce the wireless network load and improve the connection quality.

Please review the UniFi and airMAX Troubleshooting sections for further wireless help articles if necessary.

IP Address Conflicts

If the camera and another device on the network have the same IP address configured, it may cause the camera to frequently connect and disconnect. This will occur as the NVR will receive conflicting information as to what MAC address is associated with a specific IP address and as a result, NVR and camera traffic will be incorrectly routed to the wrong device.

• If the camera IP address has been manually configured, verify that the IP chosen is outside of the DHCP scope configured for the subnet on your router.
• Make sure that no other device on the network has been configured with the same IP address, either manually in the device configuration, or via a DHCP reservation (Static IP assignment) in the UniFi Controller or third-party router.

Inconsistent Camera Authentication or Configuration

Incorrect credentials, bad certificates, or other configuration related issues may cause connection failures and repeat disconnects from a camera. This is typically easily resolved by resetting and re-managing the camera:

1. In UniFi Video webUI, navigate to the Cameras section, and click on the corresponding camera to open the configuration pane.
2. Select the Manage tab and click Unmanage to expand the section. Click the Unmanage button and confirm.
   User Tip:In some browsers if there is another subsection expanded in the Manage tab, when you click on Unmanage it seems like nothing is happening. Collapse all other sections by clicking on them and try again.
3. In a new browser tab, open the camera’s web interface by browsing to the camera’s IP address as seen in the camera’s configuration pane.
4. Log into the camera interface using ubnt as the username. Depending on whether the camera was able to reconnect after it was unmanaged, the password may have been reset to ubnt, or you may need to use the Camera Password as configured in UniFi Video’s Settings page.
5. Take note of the network configuration settings if necessary, then proceed to factory reset the camera.
6. Once the reset is complete, re-manage the camera and verify configuration and connectivity.

Installation Environment

In rare circumstances, cameras that are installed in extreme conditions may experience overheating and become disconnected from the controller. Refer to the maximum environmental temperature rating for your camera model if the camera is installed in a high temperature location and relocate if necessary.

Low Bandwidth Warning

Overview

This article describes a few options to improve slow video streams which trigger the “Low Bandwidth” warning on the UniFi Video live view.

Introduction

Streaming is a very intense process for any machine. Even with newer and newer hardware, it is difficult to keep up with the demand for real time video in most use cases. This article includes a few pointers on what to check to determine the cause of the slow video stream(s) that triggers the Low Bandwidth warning in UniFi Video Live View.

This warning will appear if the client machine (i.e. computer where Live View is being used) is struggling to keep up with the demand for video decoding, or if the NVR hardware is slowing down due to some CPU intensive process. It does not necessarily mean the camera or NVR have low bandwidth.

ATTENTION:If you do not see the Low Bandwidth message like in the picture above, skip to step 2.

Step 1: Network Troubleshooting

In most cases the upload speed of one of the elements in the network is the culprit of triggering a Low Bandwidth warning. Always perform a thorough troubleshooting as described in this section first, before moving on to troubleshoot the camera.

Check the upload speed. Check the machine’s connection to the NVR—specifically the NVR’s effective upload speed. If the NVR is separated over the internet (WAN) then that network’s upload speed is a factor. You’ll need to make sure your network speed is up to the task. The following diagram shows a scenario where the UBNT cloud or port forwarding is being used to reach the NVR.

Notice the numbered connections from the camera all the way to the mobile, where a user is viewing the live video. Any one of these five connections could be the cause of the slow stream. In other words, the slowest upload speed of any of these will be the maximum speed available for the video stream.

In this second scenario, a local machine is used to view the video streams from the NVR, so the path from camera to user is shorter. Again, any of these connections can be the cause of low bandwidth. Check what the speed of each one is to determine if one of them is the cause. Typically, we find step 4 to be the culprit: make sure to check your WAN upload speed with your internet provider.

Step 2: Camera Troubleshooting

In the vast majority of cases, the Low Bandwidth warning is related to upload speeds and would become evident once the investigation mentioned in the section above is performed. In rare cases the issue will be related with the cameras. There are three ways this error could appear:

• On one camera stream
• On multiple camera streams
• On all camera streams

One Camera Stream

If symptoms only exhibit on one camera, it’s most likely a connection issue, or camera firmware issue. Try the following:

1. Reboot the camera.
2. Make sure the camera’s firmware is up to date.
3. Try swapping the camera’s ethernet cable, port, and uplink switch to cover all bases.

Multiple Camera Streams

1. If the same cameras present symptoms every time, it is likely a camera connection, or camera firmware issue. Try to establish a commonality between the cameras:

1.1 Are they on the same Switch? Test one of them on another switch or compatible POE injector.

1.2. Are they on another LAN? Make sure ports 7442 and 6666 are open to the NVR.

1.3. Are they on the same firmware? Try manually uploading a new firmware from our Downloads page on one of the cameras.

2. If symptoms appear on different cameras every time, it’s most likely a client-side processing issue. In other words, the computer used to view the video stream. To verify: open Task Manager (Windows) or the Activity Monitor app (macOS) and view the computer’s CPU usage.

You should be looking at the stats for the browser used to run UniFi Video. Mobile devices don’t always include a CPU monitor, you may have to install an app that functions as one. Alternatively, you can test on a computer to verify if the Low Bandwidth message appears, if it doesn’t, then the issue is with the mobile’s CPU is very probable that the phone’s CPU usage is at a very hione, or you can test the connection on a computer first to determine if the mobile’s speed is the problem.

All Camera Streams

In most cases this is indicative of a poor connection or a slow client-side CPU. Make sure to check the client’s CPU usage using the same instructions shown above, both before and after opening the video stream.

How to Reset a Camera to Factory Default Settings

Overview

There are two ways to reset your camera. The recommended method is to physically reset the device by using the reset button on the camera. Resetting via the WebUI is also possible in most cases. Find both processes described below.

Introduction

If you are unable to manage or otherwise configure a camera, it’s likely it will need to be reset back to factory settings. Once the reset has been completed, the camera login credentials should revert back to ‘ubnt’ for both the username and password.

Physical Reset

The reset button’s location will vary from model to model. Please check the camera’s Quick Start Guide to find its specific location. QSGs can be found in the Downloads page. Use a paper clip or a similar object to push the button within the small reset hole.

1. While the camera is powered on, press and hold the reset button for 10 seconds.
2. Release the button (the LEDs will stop glowing).
3. Do not disconnect the camera from its power source during the reboot process.
4. The camera will restore factory settings after a few minutes.

Camera WebUI Reset

Although the physical reset is the recommended method of taking your camera back to factory defaults, sometimes a WebUI reset can be more convenient. Find the camera’s IP address via WiFiman, or UniFi Video and then follow the steps below:

1. Connect to the camera’s IP address in your browser, and log in.
2. Go into the System tab.
3. Under the Maintenance section you will see the link for Reset to Defaults.
4. Click it and wait for your camera to be reset. Don’t unplug the device during this process.

How to Factory Reset an NVR Appliance

Overview

Read Next : Ubiquiti Unifi Cameras Firmware Software Download

This article explains how to reset an NVR Appliance to its original factory settings.

NOTES & REQUIREMENTS:

• The following guide is based on UniFi Video version 3.1.x and later.
• Factory resetting an NVR will remove all previous management settings and video data. Any custom configuration changes applied by the system administrator will be lost, such as file-systems mounted on iSCSI volumes or locally attached external disk drives.
• The default IP address of the NVR appliance is 192.168.1.30 (but will retrieve a DHCP-assigned address if a DHCP server is present).

Introduction

There are three methods to factory reset your NVR: via Graphical User Interface, Command Line Interface, or the reset button on the actual device. After resetting your NVR to factory defaults, please follow this article to bring it back to current firmware: UniFi Video – How to Update the NVR via SSH.

Graphical User Interface (GUI)

1. Open the NVR landing page in a browser (http://<NVR_APPLIANCE_IP>/). You do not need to include the default port “7443” as the NVR hardware itself is what will be managed, not UniFi Video.
   
2. Click on the gear icon on the upper right hand corner of the page to access the Configure Device page.
3. Log in as “root” system account (username/password should be either ubnt/ubnt or root/ubnt). If you’ve changed this password, and don’t have it anymore, proceed to the Hard (physical) reset method.
4. Navigate to the Maintenance tab.
5. Click “Reset to Defaults” button next to “Reset To Factory Defaults:”
   
6. Re-open the NVR landing page in a browser (http://<NVR_APPLIANCE_IP>/).

Command Line Interface (CLI)

1. Open a shell session to the NVR appliance e.g. ssh root@<NVR_APPLIANCE_IP>
2. Enter the following command-line
   nvr-systool reset2defaults
3. Re-open the NVR landing page in a browser (http://<NVR_APPLIANCE_IP>/).

For more options, type nvr-systool --help to list other administrative parameters. The nvr-systool is used by the NVR management console where this CLI approach is equivalent to the GUI steps.

Hard (Physical) Reset

1. Press and hold the Reset button (the crescent moon button) located below the Power button for 10+ seconds. The device will take up to 60+ seconds to restore the default configuration and return to the original factory version.
2. Re-open the NVR landing page in a browser (http://<NVR_APPLIANCE_IP>/).

UVC-Micro/G3-Micro Recovery

Overview

This article demonstrates how to recover a UVC-Micro and UVC-G3-Micro.

Introduction

The methods described in this article are comparable to a TFTP recovery done on a UVC, UVC-Dome, or UAP for example. The difference is that the UVC-Micro does not have an Ethernet interface, therefore, there is no direct way to interface with the unit via TFTP. Instead, the UVC-Micro makes use of the SD-Card slot on the back of the unit. In the case of the UVC-G3-Micro, on-board storage is used instead.

Steps: UVC-G3-Micro Recovery

1. Disconnect power from the UVC-Micro.
2. Insert a paperclip or similarly narrow object in to the reset hole on the opposing side of the LED and press down.
3. Continue holding this button while you apply power to the UVC-Micro. The LED will turn on and remain steady.
   User Tip:Hold the camera in one hand, and the paperclip pressing the button in the other. Have the magnetic base on a flat surface with the power adapter connected to the base. Slowly lower the camera over the base. The magnet will snap on, applying power. Be careful not to release the button.
4. After approximately 15-20 seconds, the LED will flash once. This is the indicator that the reset button may be released.
5. After an additional 30 seconds or so, the UVC-Micro will start emitting a tone indicating that the camera is in a default state and is ready to be provisioned.

Steps: UVC-Micro Recovery

NOTES & REQUIREMENTS:

If performing this recovery with a Windows computer, it will be necessary to download and install Win32 Disk Imager (Free). The firmware binary can be obtained from the firmware downloads page, or the Video Controller in the following places:

• Windows: C:\ProgramData\unifi-video\fw\A5S\
• Linux: /usr/lib/unifi-video/fw/A5S/

*The filename has been intentionally omitted as it will change depending on the software installed. There will be only one file in this folder.

1. Insert a microSD card (20MB or larger).
   WARNING:Contents will be overwritten. Please back up any contents that you wish to retain.
2. Write the firmware file to the microSD card. For Windows, see Note 1 below. For Linux & Mac, see Note 2 below.
   1. If using Windows follow this process:If using Windows, copy the .bin file to the same folder, then rename the copied .bin to have an extension of .img instead of .bin. Use Win32 Disk Imager to write the image to the drive letter of the microSD card.  Your result should look like this:

      

      Where:

      D:/Downloads/UVC.gen2.v3.1.0.38-devel.89002e2.150421.2034.img would be a firmware binary renamed to have a .img file extension

      [I:\] is the drive letter assigned to this microSD card by Windows. Then, all that is left is to click the Write button.

   2. If using Linux or Mac OS X follow this process:If using Mac or Linux, the dd command is used:

      dd if=/path/to/firmware/file.bin of=/path/to/microsd/card bs=8M; sync

      Root privileges may be required to be able to use dd. If this is the case, issue the following command prior to the dd command:

      sudo su -

      To find the path to your microSD card (what follows the “of=” part in the command above), you can use diskutil (Mac) or dmesg or fdisk (Linux).  Here are options for both Mac and Linux.

3. Unmount and remove the microSD card from the computer.
4. Disconnect power from the UVC-Micro.
5. Insert the microSD card into the spring-loaded slot in the back of the UVC-Micro.
6. Insert a paperclip or similarly narrow object in to the reset hole on the opposing side of the LED and press down.
7. Continue holding the reset button while you apply power to the UVC-Micro. The LED will turn on and remain steady.
   User Tip:Hold the camera in one hand, and the paperclip pressing the button in the other. Have the magnetic base on a flat surface with the power adapter connected to the base. Slowly lower the camera over the base. The magnet will snap on, applying power. Be careful not to release the button.
8. After approximately 15-20 seconds, the LED will flash once. This is the indicator that the reset button may be released.
9. After an additional 30 seconds or so, the camera will start emitting a tone indicating that it’s in a default state and is ready to be provisioned.
10. To reuse the microSD card, insert it back into the computer and reformat it.

How to Adopt a Remote Camera that is not Displaying in the NVR

Overview

This article helps troubleshoot a remote camera that is not appearing in UniFi Video.

NOTES & REQUIREMENTS:

• This procedure is not necessaryif all devices are on the same Layer 2 Network, or Broadcast domain.
• UniFi Video v3.1.5 is the last version that supports airCam models.

Introduction

This article is useful if your cameras are on a different network than your NVR, or are otherwise not appearing in your NVR’s camera list. There are two methods to adopt directly, Manual adoption, or Token Adoption. Token adoption is faster than Manual Adoption, especially when configuring multiple cameras.

Steps: Manual Adoption

1. Navigate to the camera’s web interface by entering its IP address in the browser.
2. The default username and password is ubnt/ubnt. (If unsuccessful try root/ubnt)
3. Enter the IP address of the NVR in the UniFi Video server field.

5. Click Save Changes at the bottom of the page.

6. Return to the NVR web interface by entering the NVR’s IP address in the browser.

7. On the Cameras view, enable the Unmanaged filter and locate the camera.

8. Proceed to adopt the camera.

Steps: Token Adoption

1. Navigate to the NVR’s Settings page.
2. If the Camera Adoption Token field is empty, click NEW TOKEN.
   ATTENTION:The token is only valid for 30 minutes, it will then disappear.
3. Navigate to the camera’s web interface by entering its IP address in the browser.
4. Enter the IP address of the NVR in the UniFi Video server field.
5. Enter the Adoption Token in the  Adoption Token field.
6. Click SAVE CHANGES. The Camera will automatically be adopted to your NVR.

How to Reset a UniFi Video Installation for Windows

Overview

This article will outline how to reset a UniFi Video installation and how to restore recordings under the Windows operating system. The article for resetting a Linux installation (or our hardware NVR), can be found here.

NOTES & REQUIREMENTS:

Please note that this will clear out all settings and managed cameras but therecordings will remain. If you do not restore a configuration backup, it will be necessary to re-manage the cameras, set up motion zones/sensitivities, reconnect the install to the cloud, etc. This method should only be used after a database repair has been attempted and been advised by a Ubiquiti employee.

cp /path/to/firmware.bin ~/

tftp 192.168.1.20; bin; put ~/firmware.bin

<p>The post UniFi Video Troubleshooting first appeared on NVR IPCAMERA SECURITY.</p>

In general, a power cycle of a Wyze camera can frequently resolve most problems; this is a method that is quite simple to use and works most of the time to bring Wyze devices back to work.

Why would You Power Cycle Your Wyze Camera?

There are several reasons why you should power cycle your Wyze camera. One possibility is that your commands are not being recognized by the camera. Another possibility is that the image quality is poor or that the camera is unable to connect to your Wi-Fi network. In rare circumstances, a power cycle may also alleviate difficulties with motion sensing or alarms.

How to Power Cycle Wyze Camera?

Simply unplug the power from the camera after turning it off and streamline the power connections after a few seconds. This will reboot the unit, and you will have to wait a few moments for the base station to connect to the Wyze camera. So, if you’re experiencing small issues and don’t know how to power cycle the Wyze Camera.

Note: The power cycle technique is rather straightforward despite of Wyze model or whether it is outside or inside the camera.

Simply follow these steps:

1. Unplug your WYZE device from its power source. Either from the switchboard or the camera side, both ways work.
2. Give yourself at least 10-15 seconds to let the camera completely discharge itself.
3. Plug the device back into the power source and let it restart.

How to power cycle the WYZE outdoor camera?

Simply follow this procedure:

1. Unplug your WYZE outdoor Cam from the hook.
2. Remove the batteries, wait for at least 2 minutes, and insert them back again.
3. Now again wait for at least 15 secs, and now turn it ON.

Done

How to power cycle the WYZE camera remotely?

To remotely power cycle your WYZE camera:

1. Go to the WYZE App (IOS) (Android), and select your WYZE camera from the list.
2. Power it OFF.
3. Better power off the main switch (if it is remotely controllable.) If not, skip this added caution.
4. Wait for at least 15 minutes and then restart it.
5. It should be reset as expected..

If the camera becomes fully hung up, a remote restart will never work.

You may want to install a smart switch between the camera power adapter and the socket to fix this problem. It will not be more than $10. However, if the local Wi-Fi signals are absent or poor, the problem will remain.

How do you power cycle a WYZE Cam V2?

Power cycling WYZE Cam V2 is no different from doing so with any other WYZE camera. Nevertheless, if you have power cycled it again and again, and you still can’t connect to your WYZE Cam V2, you will need to Hard Reset it.

You can find an easy way of Hard Resetting under V3 factory resetting. (Same process)

How do you power cycle a WYZE Cam V3?

1. Power cycle the camera by unplugging the power and plugging it back in.
2. If the camera returns to flashing red but never reconnects, set the camera up as a new device.
3. In the Wyze app (IOS) (Android) , tap Home then the + plus sign. Then tap Add Device > Cameras and select your camera. Follow the prompts to set up your camera again.

You will need to Hard Reset it in case the problem still persists:

To factory/Hard reset your Wyze Cam v3:

1. If you have a MicroSD card inserted, remove it.
2. With the Wyze Cam plugged into power, press and hold the setup button on the bottom of the camera for 10 seconds. This will reset the camera.
3. Wait at least 30 seconds for the unit to initiate.

This process can take up to 5 minutes. It’s rare, but it’s possible.

1. The LED status light on the device will change from Solid Red to Flashing Red.
2. The device is now ready to be set up again.

Check out the Wyze Cam Setup Guide to set up your Wyze Cam.

What Should You Do If the Camera Doesn’t Connect even after the power cycle of the Device?

There are a few troubleshooting steps you can go through:

• Step 1: Reboot your Wyze Base station by disconnecting it for 30 seconds from its power supply.
• Step 2: Check the Wyze Cam Outdoor and Base Station status lights. They should both be solid blue, but if they’re flashing, it means they’re still trying to connect.
• Step 3: Launch the Wyze app and choose the connected Base Station. If the signal strength is merely one bar, move your Base Station closer.
• Step 4: Charge the Wyze Camera for four hours outside. You may use the mobile app to check battery levels whenever you need to.
• Step 5: Open the Wyze app (IOS) (Android) and navigate to Account > Firmware > Upgrade, then hit Update. The correct software can guarantee that the devices communicate.

Why is my WYZE Cam not connecting after the above methods?

WYZE Issue Code 90 is a “common” error that might occur at any moment. However, in 97% of the cases, the offenders are as follows:

• If there is a connection problem and repeated time-outs during setup, the Wi-Fi frequency might be the culprit. Most Wi-Fi routers today support both 2.4GHz and 5GHz frequencies. As a result, you should ensure that you are connected to the 4 GHz WI-Fi network.
• WYZE Error Code 90 is also caused by slow internet connections or connections that are more limited than usual.
• Check that no significant equipment is interfering with the WYZE camera’s access to signals; otherwise, an error path may be paved.
• Corrosion and day-to-day difficulties can also occur and can be remedied by disconnecting the wires/sockets, etc. and inserting them back in. In general, you can simply overcome these annoying situations using simple ways.
• If the Wi-Fi channels get too congested, they may wind up over-consuming the minimum bandwidth required by the WYZE Cam, resulting in the WYZE Error Code 90.
• SD Card might possibly be the culprit! If the inserted SD card is corrupted, WYZE Error Code 90 will most likely appear. The reason is that SD card corruption interferes with the back processing of the camera’s live broadcasting. It sometimes entirely stops it.

Solutions Of How to Power Cycle Wyze Camera Error Code 90

If your WYZE Cam is not connecting, it may be due to a power issue. First, try power cycling the camera to see if that resolves the issue.

To power cycle your WYZE Cam:

• Unplug the power adapter from the camera.
• Wait 10 seconds.
• Plug the power adapter back into the camera.
• Wait for the green light on the front of the camera to come on, indicating that it is powered on.
• Once the green light is on, open the WYZE app (IOS) (Android) and check to see if you can view your camera’s live footage.

If the problem is not resolved then you might need to see other solutions and apply it accordingly:

1. Unburden the Wi-Fi Channel
2. Change the Wi-Fi Frequency Band
3. Establish New Wi-Fi Access Points

Unburden the Wi-Fi Channel

1. First, on your Android or Apple phone, install the Wi-Fi Analyzer App.
2. Check to check whether any Wi-Fi channels are saturated with this app.
3. You will now require a Windows PC. Switch it on.
4. When you press “Windows + R,” the Run Prompt window will appear.
5. Enter “cmd” and press “Enter.”
6. Now, type “IP config” into the command prompt and hit “Enter.”
7. Note the IP address under the “Default Gateway” header.
8. Put this IP address into the search box of any web browser.
9. You are now on the router’s Control Panel log-in page.
10. Enter the username (often “Admin”) and password (if not previously established, the code written on the back of the router).
11. Now that you’ve signed into your router, go to Wireless Settings and pick “Channel.”
12. Many channels will emerge with designations such as “1,2,3,…”
13. Using the Wi-Fi Analyzer App, choose the least saturated (least-burdened) channel from the list.
14. WYZE Error Code 90 should be resolved by changing the Wi-Fi Transmission channel.

Change the Wi-Fi Frequency Band

1. Open your web browser and type in the address bar 192.168.1.1
2. Log in with the username and password for your router (If you don’t know what they are, check the documentation that came with your router)
3. Click on the “Wireless” tab and then select the “2.4GHz” radio frequency band instead of the “5GHz” band
4. Save your changes and restart your route

Establish New Wi-Fi Access Points

If you are still unable to connect to your Wyze Cam after attempting the above-mentioned alternatives, you may need to create new Wi-Fi access points. To accomplish this:

1. Open a web browser on your PC and navigate to 192.168.1.1.
2. Enter “admin” as the login and “wyzeCam” as the password.
3. To add a new Wi-Fi access point, go to the WLAN tab and then click Add.
4. Enter a name for your new Wi-Fi access point in the Name field (e.g., Wyze Cam)
5. Enter the name of your home Wi-Fi network in the SSID field (e.g., MyHomeWiFi)
6. Enter the password for your home Wi-Fi network in the Password area.
7. Click on Save, then on Apply Changes.

You Might Want to see this:

• Wyze Cam Outdoor Setup Guide NEW
• Wyze Cam v3 Setup Guide NEW
• Wyze Firmware App Tools New

Frequently Asked Questions:

How Do I Restart Wyze Camera?

• Option One: Unplug the camera from the power source for 10 seconds, then reconnect it.
• Option number two: For 5 seconds, press and hold the power button on the back of the camera until the LED light flashes blue.
• Option three: Install the Wyze app and go to the “Device Settings” section. Tap “Restart” next to the name of your camera, then confirm by tapping “Yes.”
• Option four: If your camera is stuck and you are unable to reach Device Settings, you may factory reset it through the Wyze app. To begin, navigate to Menu > Account > My Cameras. After that, choose the camera you want to factory reset, then hit the gear icon in the upper right corner and choose “Factory Reset.”

Can you power cycle Wyze camera remotely?

Yes, you can by going to the WYZE App (IOS) (Android), selecting your WYZE camera from the list, powering it OFF and Waiting for at least 15 minutes, and then restart it.

Why is my Wyze device reset failed?

If the connection continues to fail, restart your phone or tablet and then erase the Wyze app’s cache. If the preceding troubleshooting options have failed, consider restarting the camera by going to the camera’s settings and selecting “Restart Device.”

<p>The post How to Power Cycle Wyze Camera Full Guide first appeared on NVR IPCAMERA SECURITY.</p>

1, iPhone IOS Smart Phone Installation

2, Android Smart Phone Installation

iPhone IOS Smart Phone Installation

Load More : V380 IP Camera Installation Software download

WiFi smart link installation (with WiFi Network)

1. Open Apple App Store, search, download, and install V380

2. Connect the power plug to the camera and place the camera “right next” to your WiFi router.
Camera sound: “System is starting”
Camera sound: “System startup completed”

3. Press and hold the reset button on the back of the camera until you hear the following sound:
Camera sound: “Restore factory default setting”
Camera sound: “Waiting for WiFi smart link configuration”

4. Open the app V380

Click on “WiFi Smart Link”

5. Your phone has to be connected to your WiFi network. You should then see your network name under WiFi Name. Enter your WiFi password and press next on the following screen:

6. You will see the following screen, searching for the camera through your WiFi connection

Camera sound: “Configuration received”
Camera sound: “WiFi connecting”
Camera sound: “WiFi connected”

7. Successfully installed

Note: “Add manually” option is for when a camera is already connected to your home network and you would like add the camera to another phone. You can simply press “Lan Search” or Type in the Device ID (located on the bottom of the camera) and click “Add to list” on the following page to add an already configured camera to your phone.

AP (Access Point) installation (withor without WiFi Network)

1. Open Apple App Store, search, download, and install V380

2. Connect the power cableto the camera
Camera sound: “System is starting”
Camera sound: “System startup completed”

3. Press and hold the reset button on the back of the camera to until you hear the following sound:
Camera sound: “Restore factory default setting”
Camera sound: “Waiting for WiFi smart link configuration”

4. Press and hold the reset button againon the back of the camera for 1-2 seconds Camera sound: “Access point establishing”
Camera sound: “Access point established”

5. On your phone, go to Settings -> WLAN and connect to the WiFi network that starts with MV and ends with 8 digits. For example MV12345678. This is your camera access point.

6. Open the app V380

Click on “Add Manually”

7. Your phone has to beconnected to the camera access point. On the following screen, you can simply press “Lan Search” or Type in the Device ID (located on the bottom of the camera) and click Add to list on the following screen to add the camera to your device list:

8. When your phone successfully connects to the camera, you will see your camera on the Device List.

Now your camera is setup to connect directly to your phone and can only be accessed when your phone is near the camera access point signal. To configure your camera to your WiFi network, please place the camera next to your WiFi router and. continue the following steps.

9. Click “Settings” on the bottom menu will bring you to this screen.
You will see your device ID at the top. Click “Network.”

10. Check “Station (Work with router). The “WIFI List Near the device” will populate with nearby networks. Choose your WiFi network and type in your WiFi password and press return. Then click “Save” at the very top.

Camera sound: “WiFi Connecting”
Camera sound: “WiFi Connected”

11. On your phone, go to Settings ->WLAN and connect to your WiFi network. Reopen the V380 app and click “Device List” at the bottom. You should see the camera on the device list.

12. Successfully Installed

Android Smart Phone Installation

WiFi smart link installation (with WiFi Network)

1. Open Google Play Store, search, download, and install V380

2. Connect the power plug to the cameraand place the camera “right next” to your WiFi router.
Camera sound: “System is starting”
Camera sound: “System startup completed”

3. Press and hold the reset button on the back of the camera until you hear the following sound:
Camera sound: “Restore factory default setting”
Camera sound: “Waiting for WiFi smart link configuration”

4. Open the app V380

Click on “WIFI quick setup”

5. Your phone has to be connected to your WiFi network. You should then see your network name under WiFi name. Enter your WiFi password and press “Next step” on the following screen:

6. You will see the following screen, searching for the camera through your WiFi connection

Camera sound: “Configuration received”
Camera sound: “WiFi connecting”
Camera sound: “WiFi connected”

7. Successfully installed

Note: “Searching device” and “Device Linked” option is for when a camera is already connected to your home network and you would like add the camera to another phone. Simply clicking “Searching device” will add an already configured camera to your phone. Or you can click the + icon on the top right and click Device Linked, then click “Lan Search” or Type in the Device ID (located on the bottom of the camera) and click “Confirm Add” on the following screen to add analready configured camera to your phone.

AP (Access Point) installation (with or without WiFi Network)

1. Open Google Play Store, search, download, and install V380

2. Connect the power cable to the cameraand place the camera next to your WiFi router.
Camera sound: “System is starting”
Camera sound: “System startup completed”

3. Press and hold the reset button on the back of the camera to until you hear the following sound:
Camera sound: “Restore factory default setting”
Camera sound: “Waiting for WiFi smart link configuration”

4. Press and hold the reset button again on the back of the camera for 1-2 seconds
Camera sound: “Access point establishing”
Camera sound: “Access point established”

5. On your phone, go to Settings -> WLAN and connect to the WiFi network that starts with MV and ends with 8 digits. For example MV12345678. This is your camera access point.

6. Open the app V380

Click on “WIFI quick setup”

Click on “AP Quick Setup” will bring you to the Quick Configuration screen.

7. You will see the camera access point name under Quick Configuration. Click on the name to connect to the camera.

8. You should see a list of nearby WiFi networks. Choose your WiFi network and type in your WiFi password and press return. Then click “Save” at the very top. If you don’t see your network, press the back arrow and repeat step 7.

Camera sound: “WiFi Connecting”
Camera sound: “WiFi Connected”

9. On your phone, go to Settings -> WLAN and connect to your WiFi network. Reopen the V380 app and click “My Device” at the bottom. You should see the camera on the there.

10. Successfully Installed

<p>The post V380 IP Camera Installation Manual first appeared on NVR IPCAMERA SECURITY.</p>

• Create an account with an email in the application.
• Add a new device, in this example it has been done with the AR-DOME1 model so the following option has been selected from the list of cameras:

• The APP itself will indicate the steps to follow

In the next step you have to connect the mobile with the Wifi access point, this access point must be 2.4GHz

As the APP indicates the next step is to put in front of the camera the QR that will appear on it when you press next at a distance of between 15-25cm. When the camera has made a tone, press “Listen tone”.

From this point the application will be responsible for sending the information of the wifi to which you have to link and, once completed and will be added to the Arenti account:

Once the camera has been added to the account, you have to take into account that it can’t be open in two or more mobile phones simultaneously, because when you enter the second one the session in the first one will be closed.

Because of this, the way to have the same camera in several mobile phones is to create an account for each of them and from the administrator (from which the device has been added first and the configuration has been done) share with the rest of the accounts:

At this point the manufacturer gives the possibility of a video tutorial on how to perform the sharing of the equipment.

the invited account will receive a message indicating whether to accept the camera invitation or to reject it:

<p>The post Arenti camera configuration Guide first appeared on NVR IPCAMERA SECURITY.</p>

(1) Milesight Smart Remote Management Solution

By deploying it in practical CCTV projects, Milesight CCTV Router UR32S can achieve a stable and secure connection between on-site surveillance devices and remote side professional installers or technicians. In this way, Milesight cameras and NVRs can be managed easily and remotely in a more secure and efficient way.

As it’s tailored for optimizing work efficiency, the key of Milesight Smart Remote Management Solution is simplicity. With its powerful product combination and simplified workflow, the solution enables speedy on-site problem solving remotely which greatly saves your cost and time while also enhances the quality of support service.

• For End Users: One-click Search & Easy Operation

1. Automatically search for devices connected with router on one-click
2. Configure device permissions for higher security and convenience

• For Installers or Technicians: Reduce On-site Visits & Solve Site Issues Efficiently

1. Remote access to the router and bulk configuration of devices connected to router
2. Reduce on-site visits, greatly saving time and cost

(2) Related Products

• Milesight CCTV Router UR32S
• M-Sight Pro APP V3.1.0.6 or above
• Milesight CMS V2.4.0.13 or above

Note: Here is the link to download the software.

http://www.milesight.com/support/download#software

2. Router connection

(1) Hardware Introduction

You can check the router’s interface in the picture below:

(2) Router Installation

Step 1: Insert the SIM card into the device according to the arrow icon on the device.

Step 2: Rotate antennas into the antenna connectors. Antennas should be installed vertically and the device should be placed always on a site with a good signal.

Note: If needed, you can install the router on the wall. Drill four holes on the wall by using your drill and insert four wall plugs into the holes respectively, and then use 4 pcs of M3 × 6 flat head Phillips screws to fix the router on the wall.

(3) Router Deployment

Connect the WAN port of the router to the same LAN as the devices (including cameras and NVRs) to deploy the router to your CCTV project.

• Here are two general deployment methods for your reference.

① If your project has been connected to the Internet, you can directly connect the router to the LAN port of the switch in the project, as shown below.

② If your project is not connected to the Internet, you can connect the router to the UPLINK port of the switch in the project, and insert a SIM card into the router to provide network services to the project, as shown below.

Note: If some of the devices in your project have been connected to the Internet, and the others are not connected to the Internet, it is recommended to follow method 2 to reconnect the devices that need to be configured with Milesight Router.

(4) Web GUI Access

UR32S provides web-based configuration interface for management.

Step 1: Check the LAN IP address of the router on M-Sight Pro APP.

Step 2: Enable Wireless Network Connection on your computer and search for access point “Router_******”(last 6 bits of MAC address) to connect it. Or you can connect your computer

directly to the router’s LAN port.

Step 3: After it is connected, type the LAN IP of the router to your Internet browser to log in the web GUI of routers.

If this is the first time you configure the router, please use the default settings below:

Username: admin 

Password: password

Browser: Chrome (recommended)

Note: After you login in, a window will pop up asking you to change the default password for better security.

You can also go to System – User Management – Account interface to change the password.

Step 4: go to Network – Interface – WAN interface, assign a static IP address for the router as shown below.

Then go to Network – Firewall – Security interface to enable remote access service of HTTP port.

Then Configure the IP address of computer manually or automatically.

• Go to “Control Panel” → “Network and Sharing Center”, then click “Ethernet” (It may have different names).
  
• Go to “Properties” → “Internet Protocol Version4 (TCP/IPv4) Properties”, select “Obtain IP address automatically” or “Use the following IP address” to assign a static IP manually within the same subnet of router.
  
  
• You can access the router’s web GUI via this static IP address directly.
  

Note: If you need to remotely manage devices through this router, please make sure

that the property of LAN1/WAN port is set to ”wan” and the connection type of WAN port is

set to ”Static IP” or ”DHCP Client”.

3. Configure device permissions on APP

Step 1: Enable Wireless Network Connection on your mobile phone and search for access point “Router_******”(last 6 bits of MAC address) to connect it.

Note: The router’s Wi-Fi will be automatically turned on after you install the Wi-Fi antenna and power on the router.

Step 2: Open the M-Sight Pro APP, search for and bind the router as shown below.

Username: admin

Password: password

Note: If the router cannot be found, we recommend clicking the help button to solve the problem.

If your project is not connected to the Internet, after logging into the router, you need to select the network access mode to complete the network settings.

• There are two network access modes are available as shown below.
  

Step 3: Select the devices you want to share with installers or technicians from the list of detected devices.

Step 4: Go to My Devices interface to modify sharing permissions and router configuration.

It supports to enable or disable device sharing with one click.

You can also click ‘’ button to check the status of the WAN port or the SIM card interface as shown below.

Or you can click ‘’  button to modify the network configurations of the router.

Note: The default connection type of the router’s WAN port is DHCP Client. You can manually switch to the Static IP type on the WAN settings interface, and configure the router and the device to share the same network segment to manage these devices remotely from Milesight CMS side.

4. Remote management on Milesight CMS

Step 1: Open Milesight CMS, go to Remote Maintenance interface.

Note: In User interface, you can configure Remote Maintenance permission for the user as shown below.

Step 2: Click “Add Router” button, enter the SN code, Router Name, User Name and Password, and then click “Add” button to add the router.

Note: You can check the SN code on the sticker or web GUI of the router.

After the router is successfully added, it will be displayed in the list on the left side, you can click the ‘’ button to delete it, or you can click the ‘’ button to configure the router.

Step 3: The devices shared by the end user will be listed here. Select the device type, check the device you need to configure, then enter the user name and password, and you can modify the device parameters on the right side.

Currently the following configurations are supported:

• Maintenance: Device Upgrade/Reboot/Reset/Configuration File/Diagnose File/Time Syn
• Network: Device Activation/Network Settings/DDNS Setup/UPnP Setup
• Camera Configuration: Video/Audio/Image parameters in detail
• NVR Management: Channel Status

Click the apply button, it will display “Modified successfully” in the status column.

Note:

①If the configuration fails, you can also check the reason in the status column.

②It also supports batch configuration, just check multiple devices that need to be configured, and then enter the same username and password.

Step 4: Click the ‘’ button to access the web GUI of the device for further configuration.

<p>The post How to Use Smart Remote Management Solution first appeared on NVR IPCAMERA SECURITY.</p>

PoE Injectors 802.3af

Smart doorbells are low power consumption devices which their maximum power rate is below 10watt, because of this reason, users can take advantage of PoE technology to have a cost-effective and maintenance-free video doorbell system. PoE stands for Power over Ethernet, as the prevalent technology in IT field (PoE for access points, IP telephone, network switches), 802.3af standard has been universally accepted and adopted by different manufacturers.

Smart doorbell has an Ethernet port and complies PoE

Users can choose any PoE injector that complies 802.3af standard. The PoE injectors support 48V, 500mA specification. The PoE injector has two Ethernet port; one LAN port to connect with your router/switch, another PoE port connects to your smart doorbell.

Smart doorbell has an Ethernet doesn’t support PoE

As long as your smart doorbell has an RJ45 port, you can take advantage of PoE by using a PoE injector and PoE splitter. The PoE splitter can split the power and data from Ethernet cable, it should be connected by the end of your smart doorbell.

If you have bought SD-M5 and SD-M3, please choose a standard PoE injector works on mode A (1,2,3,6). PoE injector works on mode A (End-span) utilizing data pairs 1-2 and 3-6 to deliver power. Both SD-M5 and SD-M3 cannot work with none-standard PoE injector (Mid-span) that utilizes 4,5,7,8 pairs.

<p>The post How to choose PoE injectors for wired smart doorbells first appeared on NVR IPCAMERA SECURITY.</p>

Playlist

2 Videos

 

V380 and V380 PRO

5:02

 

V380 Pro Apk Home Security Camera Settings

13:01

<p>The post V380 Pro Camera Instructions for use first appeared on NVR IPCAMERA SECURITY.</p>