ACH20-1B Thermal Monocular Camera: Using the App

Take some time to learn about using your thermal monocular camera through the companion Thermal Connection app.

Live View Settings

The Live View is the first screen you will see when your camera connects to the app. It includes the following features:

Digital Zoom

Zoom in on a certain part of your camera’s image to magnify details.

1.From Live View, tap .

2.Tap your preferred zoom range.

3.Tap OK to save.

Color Palette

Select your camera’s color palette for enhanced visual representations of thermal imaging.

1.From Live View, tap .

2.Tap on one of the following color palettes:

Note: Not all color palettes are suited for every situation. Select the option that best shows the thermal differences for your specific application.

Record Images & Videos

1.From Live View, tap .

2.Tap the screen to display the capture and record icons.

3.To capture images: Tap .

4.To start or stop recording videos: Tap .

Note: A blinking red dot next to a recording timer on the left of the screen indicates that your camera’s recording.

Function Settings

Enable some of your camera’s features, like the laser pointer, fire detection, or track hot and cold points.

Laser Pointer

Use the laser pointer to illuminate a point of interest with a bright spot of colored light.

 LASER RADIATION:

Exposure to laser light can cause significant damage to the eyes. Never look into the laser beam directly or through a piece of optical equipment.

After a few seconds, the laser pointer automatically turns off.

Fire Detection

Detect fires in your camera’s image with a red box surrounding the source. If enabled, you can set the fire detection sensitivity from high to low.

Hot & Cold Points

Track the hottest and lowest temperatures in your camera’s image at the same time. If enabled, your camera’s image will display a red target tracking the hottest point and a blue target tracking the lowest point.

System Settings

Customize your camera’s system settings or sign out.

Automatic Sleep Mode

Select how long your camera waits before entering sleep mode.

Automatic Shutdown

Select how long your camera waits before turning off.

Change Measurement Unit (Meter to Feet)

Change your camera’s measurement unit.

Sign Out

Disconnect your camera from the app by signing out of the app.

Restore to Default Settings

Restore your camera’s menu and app settings to its factory default settings.

ACH20-1B Thermal Monocular Camera: Troubleshooting

The following article provides some troubleshooting tips for using your thermal monocular camera.

.

Camera’s image/screen is blurry.

Adjust your camera’s diopter to your eyesight. Before you begin, it is highly recommended that you adjust your camera’s diopter to your eyesight. Focusing your view will minimize eye strain and fatigue.

Camera’s Wi-Fi hotspot is not showing.

• Wait a moment for it to appear in your phone’s Wi-Fi settings.

• When enabling your camera’s hotspot in your camera’s settings, try to press  a couple more times.

• Ensure you have allowed the app to use your location, otherwise it will not be able to detect your camera’s Wi-Fi. Navigate to your phone’s settings, then open the Thermal Connection app settings, and enable Location — While Using the App.

Camera is not connecting to the app.

The Wi-Fi password is case sensitive. Make sure you enter the serial number in the same letter format, whether that is uppercase or lowercase.

Camera has disconnected from the app.

Camera’s Live View is frozen in the app.

If the Live View is frozen perform a hard close of the app, then open it again.

Digital zoom is not working.

Digital zoom will not work while your camera’s menu is open. Press  to exit the menu.

Camera is not recording images and videos.

Recording images and/or videos will not work while the menu is open or when your camera is connected to a computer. Press  to exit the menu.

Camera’s screen is black.

Restart your camera. Press and hold  to turn your camera off, and then back on.

Camera is not charging or slow to charge.

• Ensure you use the supplied micro-USB cable and that it is properly connected.
 DANGER

◦ Improper battery replacement or use may result in fire, explosion, or other hazards.

◦ Only use accessories regulated by the manufacturer. Never use the charging cable or power adapter with another product.

◦ Make sure the plug is properly connected to the power socket.

◦ DO NOT charge your camera within 2 m of flammable materials.

◦ DO NOT connect multiple devices to one power adapter. The plug in the power socket could overheat and possibly cause a fire.

• Ensure the USB Mode is set to Off.

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to USB Mode.

◦ Press  to open the setting.

◦ Press  to select Off.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

Camera’s battery keeps draining.

You can preserve your camera’s battery life in the following ways:

• Turn off any camera settings or functions that are not being used.

• Use your camera without the app. First, sign out your camera from the app, and then turn the Wi-Fi hotspot off. 

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to WiFi.

◦ Press  to open the setting.

◦ Press  to select Off.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

• Set your camera to go into automatic sleep mode after 1 minute of inactivity has passed. First set your camera’s sleep mode (Suspend Mode) to be automatic, and then set the automatic sleep mode (Auto Suspend) to 1 minute.

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to Suspend Mode.

◦ Press  to open the setting.

◦ Press  to select Automatic.

◦ Press  to confirm your setting.

◦ Press  to navigate to Auto Suspend.

◦ Press  to open the setting.

◦ Press  to select 1 Min.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

• Set your camera’s screen brightness to low.

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to Brightness.

◦ Press  to open the setting.

◦ Press  to select Low.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

• Set your camera’s automatic shutdown to 60 minutes or less. 

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to Auto Shutdown.

◦ Press  to open the setting.

◦ Press  to select 60 Mins or less.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

Camera’s image has lots of graininess or scratches.

• Turn your camera off, attach the lens cap, and allow it to rest for a few hours before using again.

• To improve your camera’s image quality set the FFC Mode to Auto. 

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to FFC.

◦ Press  to open the setting.

◦ Press  to select Auto.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

• To manually correct pixel defects in your camera’s image, set the DPC settings to Manual. 

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to DPC.

◦ Press  to open the setting.

◦ Press  to select one of the options:

· Auto: (Default) Your camera automatically calibrates defective pixels.

· Press  to start auto DPC.

· Close the lens cap until your camera signals that auto correction is complete.

· Manual: Correct the defective pixels manually.

· Press  to start DPC manually.

·  Press to switch between the X-axis and Y-axis.

· Press and hold  or  to start correction.

· Restore: DPC is restored to original state.

◦ Press  to confirm your setting.

◦ Press  the exit the menu.

ACH20-1B Thermal Monocular Camera: Frequently Asked Questions

The following FAQ answers many of the general questions about your thermal monocular camera.

.

How does my thermal monocular camera work?

To improve the visibility of objects in complete darkness, haze, or tough conditions, your thermal monocular camera uses infrared sensors to detect heat given off by a person, animal, or other objects. It creates images of that radiation called thermograms, which display the relative temperatures of different objects with different shades or colors. In a thermogram, warm objects stand out in a contrast or often cooler background. It is widely used in outdoor scenarios for hunting, rescue, animal observation, and more.

Is my thermal monocular camera battery-operated or hard wired?

Your thermal monocular camera is battery-operated, however, to charge the battery you will need to connect the micro-USB cable into your camera’s USB port and the other end into a power source.

Does my thermal camera only work at night?

No. Although thermal imaging cameras are most commonly used for nighttime vision, they can also be useful in daylight. The detection of heat radiation and the high contrast of thermal imaging cameras allow you to see the outlines of (warm-blooded) animals that camouflage well in their environments. It can also help distinguish animals or people in foggy or smoky conditions.

Can my thermal camera see-through walls, metal, or glass?

No, thermal imaging cameras do not see-through surface but detect surface temperatures.

Is thermal imaging and night vision the same thing?

No, thermal imaging can produce pictures without visible light while night vision cameras work by boosting ambient light. Their only common purpose is increasing visibility in low light conditions.

Can bright sunlight damage my camera’s lens?

Yes, aiming your camera’s lens with the lens cap open at powerful light sources (i.e. the sun) is not recommended, as this may adversely affect the accuracy or damage the thermal imager.

What is the clicking noise my camera makes?

This is simply the noise your camera makes while you are shifting it between different fields of view. The noise you are hearing is your camera focusing and calibrating the image to achieve the highest resolution possible.

Should I charge my camera’s battery before first use?

Since your camera’s battery is delivered partially charged, it is recommended that you fully charge it before first use.

How do I charge my camera’s battery?

Your camera has the following 4 battery charging statuses, as shown by the LED charging indicator located under the USB port.

How do I turn my camera on or off?

Press and hold .

Where can I find the mobile app?

The Thermal Connection Application can be downloaded on your smartphone with a valid Internet connection from iTunes or Google Play respectively.

See the article Connecting to the App for more details.

Why do I need to allow my Location Permission on the app?

The app requires permission to detect your Wi-Fi network in order to connect your camera to the app.

How do I connect my camera to the app?

See the article Connecting to the App for full details.

How do I disconnect my camera from the app?

For steps on disconnecting your camera from the app, see the article Using the App.

What is my camera’s Wi-Fi name and password?

Where can I find my camera’s serial number?

Your camera’s serial number can be found on:

• The serial tag located on the side of your camera.

• Your camera’s system information.

◦ Press and hold  to open the menu.

◦ Press  or  to navigate to (System Information).

◦ Press  to open your camera’s system information.

How do I record images & videos?

• To capture images: Press 

• To start or stop recording videos: Press and hold  for 3 seconds. A blinking red dot next to a recording timer on the left of the screen indicates that your camera is recording.

Note: Your camera cannot record images or videos while the menu is open or when connected to a computer.

For steps on recording images and videos from the app, see the article Using the App.

How do I zoom in my camera’s image?

To switch the zoom range: Press . Keep pressing to zoom in and out.

For steps on using digital zoom from the app, see the article Using the App.

How do I turn the laser pointer on?

 LASER RADIATION:

Exposure to laser light can cause significant damage to the eyes. Never look into the laser beam directly or through a piece of optical equipment.

To turn the laser on: Quickly press  two times.

For steps on using the laser pointer from the app, see the article Using the App.

How do I change my camera’s color palette?

To quickly change the color palette: Press .

For steps on switching the color palette from the app, see the article Using the App.

Which color palettes can I choose from?

Select your camera’s color palette for enhanced visual representations of thermal imaging. Switch between any of the following color palettes:

Note: Not all color palettes are suited for every situation. Select the option that best shows the thermal differences for your specific application.

How do I measure my target’s distance?

Measure the range distance between your camera and your target using the pre-set ranging modes for animals, people, etc.

• Press and hold  to open the menu.

• Press  or  to navigate to Ranging Mode.

• Press  to open the setting.

• Press  to select one of the options:

◦ Wolf: Measure your distance from a wolf, with a pre-set height of 1.2 m.

◦ Customize: Enter a custom height to measure your distance from your target.

◦ Wild Boar: Measure your distance from a boar, with a pre-set height of 0.9 m.

◦ Human: Measure your distance from a human, with a pre-set height of 1.8 m.

◦ Rabbit: Measure your distance from a rabbit, with a pre-set height of 0.3 m.

• Press  to confirm your setting.

• Press  to exit the menu.

How do I change my camera’s measurement unit?

For steps on changing the measurement unit from the app, see the article Using the App.

How do I track hot & cold points?

Track the hottest and lowest temperatures in your camera’s image at the same time. If enabled, your camera’s image will display a red target tracking the hottest point and a blue target tracking the lowest point.

• Press and hold  to open the menu.

• Press  or  to navigate to Hot Point.

• Press  to open the setting.

• Press  to select one of the options:

◦ Off: Hot and cold points is turned off.

◦ On: Your camera will track hot and cold points.

• Press  to confirm your setting.

• Press  to exit the menu.

For steps on enabling hot & cold points from the app, see the article Using the App.

How do I enable fire detection?

Detect fires in your camera’s image with a red box surrounding the source. If enabled, you can set the fire detection sensitivity from high to low.

• Press and hold  to open the menu.

• Press  or  to navigate to Fire Warning.

• Press  to open the setting.

• Press  to select one of the options:

◦ Off: Fire detection is turned off.

◦ High, Middle, or Low: Your camera will detect fires based on the sensitivity level.

• Press  to confirm your setting.

• Press  to exit the menu.

For steps on setting fire detection from the app, see the article Using the App.

How do I enable the fire detection alarm?

Set your camera to sound an alarm when fire is detected in the image.

Note: The fire detection alarm works only when your camera has fire detection enabled on either High, Middle, or Low.

• Press and hold  to open the menu.

• Press  or  to navigate to Alarm.

• Press  to open the setting.

• Press  to select one of the options:

◦ Off: Fire detection alarm is turned off.

◦ On: Your camera will sound when fire is detected.

• Press  to confirm your setting.

• Press  to exit the menu.

How do I export recordings?

Export recorded images and videos from your camera’s microSD card.

• Press and hold  to open the menu.

• Press  or  to navigate to USB Mode.

• Press  to open the setting.

• Press  to select Mass Storage.

• Press  to confirm your setting.

• Connect the micro-USB cable into your camera’s USB port and the other end into an available USB port on your computer.

• The microSD card’s storage will open on your computer desktop. Select files to export, then copy them onto your computer.

• After exporting, disconnect the micro-USB cable from your camera and computer.

• Press  to select USB Mode Off.

• Press  to confirm your setting.

• Press  to exit the menu.

Where does my camera store recorded images and videos?

Your camera stores recorded images and videos onto the microSD card.

What is my camera’s maximum storage capacity?

You can insert a microSD card with up to 256GB storage space.

How do I hide the icons on the top right of my camera’s image?

• Press and hold  to open the menu.

• Press  or  to navigate to Status Bar.

• Press  to open the setting.

• Press  to select Off.

• Press  to confirm your setting.

• Press  to exit the menu.

How do I change the language displayed in my camera’s menu?

• Press and hold  to open the menu.

• Press  or  to navigate to Language.

• Press  to open the setting.

• Press  to select your preferred language.

• Press  to confirm your setting.

• Press  to exit the menu.

Note: This will only change the language in your camera’s menu, not the app.

How do I restore my camera’s settings to default?

For steps on restoring your camera’s settings to default from the app, see the article Using the App.

How do I update my camera?

Update your camera through the microSD card.

Note: To download the latest firmware update for your camera, contact the Technical Support team.

• Press and hold  to open the menu.

• Press  or  to navigate to USB Mode.

• Press  to open the setting.

• Press  to select Mass Storage.

• Press  to confirm your setting.

• Connect the micro-USB cable into your camera’s USB port and the other end into an available USB port on your computer.

• The microSD card’s storage will open on your computer desktop. Copy the update program to the microSD card.

• Press and hold  and  at the same time for 3 seconds. A blue screen will indicate that an update is in progress.

After a few minutes the update will complete and you will see your camera’s live view image.

Where can I download my camera’s latest firmware update?

To download the latest firmware update for your camera, contact the Technical Support team.

Can I mount my camera to a tripod?

Yes, the tripod thread can be found on the bottom of your camera.

Can I access my camera’s Live View from an external monitor?

Yes, you can access your camera’s Live View from your computer by connecting your camera using the micro-USB cable.

What is the buzzer option in the app settings?

The buzzer is not compatible with your camera.

ACH20-1B Thermal Monocular Camera: Connecting to the App

Follow the steps below to connect your thermal monocular camera to the Thermal Connection app.

Note: The frequency bands and transmitting power (radiated and/or conducted) nominal limits applicable to this radio equipment are as follows: Wi-Fi 2.4 GHz (2.4 GHz to 2.4835 GHz) 20 dBm.

.

Step 1 – Download the App

Download your camera’s mobile app, Thermal Connection.

.

Step 2 – Enable Your Camera’s Wi-Fi Hotspot

Looking into your camera:

• Press and hold  to open the menu.

• Press  or  to navigate to WiFi.

• Press  to open the setting.

• Press  to select AP (Access Point).

• Press  to confirm your setting.

• Press  the exit the menu.

Step 3 – Connect to the App

You will now be able to view your camera from the app and make some minor setting adjustments.

.

<p>The post Thermal Monocular Camera user manual first appeared on NVR IPCAMERA SECURITY.</p>

VOSKER V300 Ultimate Camera Setup and User Guide

HOW TO UPDATE YOUR V300 ULTIMATE CAMERA FIRMWARE

VOSKER V300 Ultimate
.

Latest firmware released: January 23, 2024

Installation instructions for PC :

Installation instructions for MAC :

How to Install your V300 Ultimate Camera

Before installation

Verify:

What you’ll need for installation

Choose between:

Recommended installation – Camera

Recommended installation – Universal Solar Power Bank

For more information on how to install your VOSKER camera to get the best picture quality, read the article “What Can I Do To Increase My Photo Quality?”.

Download:

› Quick Start Guide (PDF)

Troubleshooting steps:

If the Universal Solar Power Bank is discharged, charge it by plugging the DC power adapter in the 5 V IN port.

CAUTION:

WARNING: Failure to follow these safety instructions may result in fire, electric shock, damage, or other injuries. This power pack is not a toy. Keep away from children and operate outside.

.

HOW TO INSTALL YOUR V300 CAMERA

Before installing your camera, we recommend that you test the coverage of the location you will be placing your camera. Consider using a VOSKER security box to protect your V300 security camera against theft and breakage.

Here are some of the best practices for installing your VOSKER camera:

Note: Make sure to place the camera in an area that gets a good amount of sunlight during the day (enough to cover 50% of the solar panel). This will help maximize the battery life of your camera.

For more information on how to install your VOSKER camera to get the best picture quality, read the article “What Can I Do To Increase My Photo Quality?”.

.

HOW TO ACTIVATE MY V300 CAMERA?

Before activating your camera:

Note: A 24-hour charge of the battery unit is recommended before the first-time installation.

Activating your camera with VOSKER mobile app:

Activating your camera with the VOSKER web app:

Turning your camera on:

The V300 powers on and secures a strong signal.

Note: There may be a 20-120 seconds delay for the camera to make the first communication or transfer the first photo/video to the app.

EVERYTHING YOU NEED TO KNOW ABOUT V300 LIVE STREAMING

A strong cellular signal on both devices will ensure smooth live streaming.

The V300 series offers the amazing feature of live-streaming as a 40-minute add-on that can be shared between compatible devices over a 12-month period.

Want to test it out first? Upon activation, every V300 includes two minutes of live streaming during the free seven-day trial period.

How to start a live-streaming

What is the difference between live-streaming and 10-second Full HD video?

The live-streaming allows you to see what is happening live around your camera. It can last as long as you have live-streaming minutes in your account. It is great when you receive a notification, and you want to check if there are still some movements.

Your camera stores a 10-second Full HD video on the servers at every detection. You can request the video to understand better what happened during the detection. Simply click on a photo and press the button “Request Full HD video”.

What is the impact on the battery life?

The more you use those features, the more it takes a toll on the battery life.

This is especially true if the V300 doesn’t get a steady and strong signal. Just like your cell phone, the camera will work harder to connect to the cellular tower and communicate information.

If you see the battery life dropping, consider adding the Universal Solar Powerbank to sustain your camera from 6 to 12 months.

How to buy additional live-streaming minutes?

You can easily purchase a live-streaming add-on which will add 40 minutes shareable among all VOSKER streaming devices for the next 12 months.

Mobile app:

Web app:

Warning: you need a transmission plan (Base, Alerted or Elite) before buying the live-streaming add-on.

.

<p>The post VOSKER V300 Ultimate Camera Setup and User Guide first appeared on NVR IPCAMERA SECURITY.</p>

Learn About Active Deterrent Security Cameras

What Are Active Deterrent Security Cameras?

Active deterrent security cameras aren’t your typical security devices. They integrate advanced technology to proactively prevent criminal activities. Key features include built-in lights, sirens, sounds, and two-way audio.

The Importance of Active Deterrent Security Cameras

You might be wondering, why go the extra mile with these advanced features? Well, the answer is simple: prevention is better than cure. These cameras are designed not just to record incidents but to prevent them altogether.

Crime Prevention

A well-placed security camera can make all the difference. Thieves and intruders are less likely to target a property laden with visible deterrents.

Enhanced Safety

Knowing that your premises are being actively monitored can make you feel safer. Immediate alerts and real-time communication add an extra layer of safety.

Peace of Mind

There’s nothing like the peace of mind that comes from knowing your loved ones and valuables are secure. Active deterrent cameras provide a constant layer of security, ensuring you sleep a little easier at night.

Key Components of Active Deterrent Security Cameras

SIREN AND SPOTLIGHT

Active Deterrence security cameras can activate a loud siren with flashing light or spotlight when motion is activated to deter any potential threats. The light and sound features can be easily customized to meet your specific needs. These cameras are equipped with both traditional infrared night vision and LED spotlight mode for full color images at night when desired. Further, you can set the motion detection to trigger only when humans and/or vehicles are detected to produce the most accurate motion alerts.

Lights

These cameras often come with powerful LED lights that can illuminate large areas. Imagine being able to light up your entire driveway or backyard!

Siren

An ear-piercing siren can scare off even the most determined criminals. As soon as suspicious activity is detected, the siren can be activated to alert both you and the intruder.

Two-Way Audio: A Game-Changer

Two-way audio allows you to communicate in real-time through your security camera system. This feature enhances the effectiveness of the camera by enabling you to interact directly with whoever is on your property.

All our active deterrence security cameras have a built-in microphone and speaker for 2-way audio functionality from your smartphone using our mobile app. The 2-way audio feature provides an extra layer of security by enabling real-time, remote communication with individuals near the security camera. The 2-way audio feature can be used in many different scenarios.

Benefits of Having Two-Way Audio

Advantages of Lights in Security Cameras

Deterrence Effect

A bright light shining in the face of a potential intruder can be incredibly disorienting and threatening. It’s a simple but effective means of deterring unwanted visitors.

Visibility in Low-Light Conditions

If criminals think they can hide under the cover of darkness, security lights will make them think twice. These lights ensure your cameras capture clear footage, no matter the time of day.

Advantages of Sirens in Security Cameras

Immediate Alert

Imagine hearing a siren blaring in the middle of the night because someone tried to break into your home. That’s an alert you can’t ignore!

Deterrence to Intruders

The sound of a siren is universally understood as a signal to leave immediately. It’s a powerful tool that can send intruders running before they do any damage.

Advantages of Sound in Security Cameras

How Two-Way Audio Enhances Security

Real-Time Communication

Two-way audio adds a dynamic layer to home security. You’re not just watching; you’re interacting.

Interactive Deterrence

Being able to speak directly to someone on your property – whether friend or foe – provides a significant deterrent effect. Just imagine telling a suspicious individual that the police are on their way!

Installation and Setup

Easy Installation Tips

Setting up these cameras is straightforward. Most models come with comprehensive guides, and you can have them up and running in no time.

Choosing Strategic Locations

Placement is key. You want to cover all entry points and any other areas that could be potential targets.

Best Practices for Using Active Deterrent Security Cameras

Regular Maintenance

Keep your cameras clean and check for any updates to the software. Regular maintenance ensures your system remains effective.

Updating Software

Cybersecurity can’t be overlooked. Ensure your cameras are running the latest firmware to protect against hacking and other cyber threats.

Popular Brands and Models

Overview of Leading Brands

We at CCTV Security Pros offer a variety of active deterrent security cameras

Comparison of Top Models

Learn more about our top active secuity cameras and systems here!

Cost vs. Benefit Analysis

Initial Investment

Active deterrent cameras can require an upfront investment. However, what you spend now can save you thousands in potential theft or damage costs.

Long-Term Savings

Consider the long-term benefits: lower insurance premiums, reduced risk of theft, and peace of mind. Over time, these cameras pay for themselves.

Customer Reviews and Testimonials

Real-Life User Experiences

There’s no better way to gauge effectiveness than by hearing from those who’ve used these systems. Real user reviews often provide insights you won’t find in product descriptions.

Effectiveness in Various Scenarios

From deterring package thieves to keeping an eye on nighttime activity, these cameras have proven effective in a myriad of situations.

Conclusion

In today’s unpredictable world, security can’t be taken lightly. Active deterrent security cameras with lights, sirens, sound, and two-way audio offer a comprehensive solution to protect your home or business. From deterring intruders to providing you with peace of mind, these advanced systems are worth the investment.

To purchase, learn more, or view our full line of security cameras and systems.

FAQs

.

<p>The post ​Active Deterrent Security Cameras first appeared on NVR IPCAMERA SECURITY.</p>

How to add a Hikvision NVR to Hik-Connect

Before you start…​

Part 1: Enable Hik-Connect on the NVR…​

.

.

.

.

Part 2: Set up Hik-Connect on your mobile phone or tablet…​

.

.

.

Part 3: Add the NVR to your Hik-Connect account…​

.

.

.

Other tips…​

Guides for Hikvision NVRs with V5 firmware

How to set up motion detection and alerts on a Hikvision NVR

What is Motion Detection and why is it useful?​

Motion detection is one of the easiest events to set up and will notify you as soon as a person or vehicle enters a predefined detection zone in your scene. Traditionally, it would just rely on lots of pixels changing between frames in your camera’s video stream, which would indicate movement in the scene.

Of course, this would cause lots of alerts for things you are not interested in, such as animals, moving plants and rain. Hikvision’s Acusense cameras and NVRs now have something called Motion Detection 2.0, which cuts the false-positive detections right down as will only notify you when people and/or vehicles are in the scene by learning what they look like. In this simple step-by-step guide, we will show you how to get motion detection set up on the new NVR 5.0 web interface.

Step 1: Go to your NVR’s Motion Detection configuration page…​

Step 2: Configure your Motion Detection zone and rules…​

​

Quick tip…​

If you find that the camera preview is too small when drawing your detection zones, you can switch the view to full screen by clicking on the Full screen (four arrows) button in the toolbar, and then exit full screen by pressing Esc on your keyboard.​

Step 3: Set the arming schedule to specify when you want Motion Detection active…​

​

Quick tip…​

If the 30-minute segments are not precise enough for you, you can finely tune a period of arming or disarming by double-clicking on the segments and specifying your start and end times in minutes using the arrows.​

​

Step 4: Set what you need the NVR to do when a camera detects a target…​

How to connect an IP camera to a Hikvision NVR

Adding cameras to your Network Video Recorder (NVR) is a crucial step in any CCTV setup. Not only does it allow you to store and access all your camera recordings in one place, but it also simplifies camera configuration. In this simple step-by-step guide, we’ll show you how to add cameras to a Hikvision NVR using the new NVR 5 web interface.

.

Why add cameras to an NVR?​

.

Before you start…​

Before anything, to be able to add your IP cameras, you need to make sure that:
.

.

How to add your cameras using the V5 GUI…​

Step 1:​

Open a web browser and enter the IP address of your NVR in the address bar. If you are not sure what this is, use the SADP tool to find it.​

Step 2:​

Log in to the NVR using the “admin” username and password you have set on it.​

​

Step 3:​

Go to: Device Access > Device Configuration > PoE Settings​

​

If you are connecting your camera via the Plug-and-Play method, then make sure that Network Camera Plug-and-Play is enabled on the POE port you will be connecting the camera to on this page.​

​

For any camera with a cable run under 100m, leave the Network Cable Distance as Short Distance.​

​

If you are connecting your camera manually by IP address, disable the Network Camera Plug-and-Play option for the channel that you plan to add the camera to.​

Step 4:​

Go to: Device Access > Device > Video Device​

​

For any Plug-and-Play camera, just make sure that it is in its inactive default state and then connect it to the port you reserved in step 3. After 20 seconds or so, the camera Status should turn to Connecting and then Online (you may need to click on Refresh to see this).​

​

For Manually added cameras, if you can see the camera in the List of Online Devices section, then just tick the box for the camera and then click + Add to Device List, which will then automatically add it to one of the channels you disabled Plug-and-Play on in the last step.​

Alternatively…​

Click on +Add at the top of the page and fill out the fields as follows:​

​

IP Address: Enter the IP address of your camera, using the ‘Test’ button to verify there is a camera at that address. ​

Device Name: This can be anything you like, as it is the name the camera will show with on your NVR. ​

Protocol: Select the camera’s manufacturer from this list, or failing that, use the ONVIF protocol (your camera will need to have ONVIF enabled for this to work). ​

Management Port: Enter the Server port set on the camera, which you can find in the SADP tool or in Network>Basic Settings>Port in the camera’s web browser interface. If you haven’t changed this, it is usually 8000 by default. ​

User Name: “admin” or the username of any other users set up on that camera. ​

Password: The password set with that user on the camera – if this is the same as the ‘Default Activation Password‘ you have set on the NVR, then you can tick this box instead. ​

Transfer Protocol: ‘Auto’ is normally best. ​

​

When these are completed, click OK.​

​

Your camera should then appear in the list of devices with an assigned channel, and an Online status, meaning it has been successfully added.​

.

Extra tips…​

Source : https://www.use-ip.co.uk/forum/forums/guides-for-nvrs-with-v5-firmware.71/

.

<p>The post Guides for Hikvision NVRs with V5 firmware first appeared on NVR IPCAMERA SECURITY.</p>

We can talk directly on phone app for asking courier to put package to a certain place you point, and hear sound from app or TV monitor connected to NVR

We could be alerted any time a person enter your property by receiving push notification from free phone APP, and the alarm light will be triggered to drive away the suspicious objects ( Note: APP has No Monthly Fees)

High Resolution 2592 X 1944 pixel to provide your vivid and clear image no matter in day or night, and IP 67 Waterproof to withstand Changeable Weather like Snowy/Rainy Day

We can customize the surveillance area or set a line for human/vehicle, and the alarm alerts will be triggered when detecting human/vehicle crossing the line or intruding the alarm area （These function may only work with Hiseeu NVR）

Version 2020-2022 PoE System FAQs in total

.

Further support, plz email us at email love@hiseeu.com

Or contact us at +1 917 688 2228

.

Important Notes:

These FAQs are only adaptable to following Models NVR Model : H5-NVR-P-8,

Camera Model: HB215-PA, HB212-PA, HB915B-PA

Mobile Phone APP: XMEye Pro         PC Client :VMS

Hisseu PoE Camera System User Guide v1

Contents:

A:  Forget NVR Password?

B:  Add Device on PC Client Software (VMS）?

C:  How to Sign up account on Mobile APP (XMEye Pro) ?

D:  Add Device on Mobile Phone APP (XMEye Pro)?

E:  How to enable Alarm Notifications on APP XMEye Pro?

F:  Configure Offline Camera or Add a New Camera?

G:  No Video Display on TV Monitor Or Blank Screen?

H:  Why DVR/NVR can’t record or playback video?

.

Detail Solutions:

A:  Forget NVR Password?

1. Please click the mouse from the home screen, and “Logo Out–>Log Out”

2. Right click the mouse again, click “ Main Menu”–> “Forget password –> Forget answer”, you will see the “QR Code”

3. Please open your mobile APP “XMeye Pro”

（1）Click the Scan icon on the top left corner

（2）Scan the “CAPTCHA” on the TV monitor, then you will get a code from the mobile phone APP or from your email, and enter the code into “CAPTCHA”, so you will be able to reset the password on the Monitor connected to DVR

.

B: Add Device on PC Client Software (VMS）?

VMS download link:

For Windows （2023 newest version）

https://download.xm030.cn/d/MDAwMDE0OTM=

For Mac ( 2022 version)

https://download.xm030.cn/d/MDAwMDA2NDA=

1. Download PC Client “VMS” and installed

2. Login with the default User Name and Password. Click “SIGN IN”.

Default User name is: admin

Default Password is: admin

3. Navigate to “Device Manager”–>”Manual Add”

4. Login Type: Cloud ID Device Name:

Name Your Device as you like

Cloud ID : Device Serial Number. We need to go to the TV Monitor connected to the NVR , and find out the information on TV Monitor UI, then right click the mouse to navigate to the path of “Main Menu–>Advanced–>Version” to find out the information “serial number”

User Name and password: Input the user name and password that you created for the NVR , and we also need to find this from the Monitor UI.

.

5. Navigate to “Live View”, Click on the device name(serial number), then select “Open All By Sub Stream”

.

C:  How to Sign up account on Mobile APP (XMEye Pro) ?

Please follow these instructions to sign up for an account via your mobile number.

1. Click on Sign Up

2. Sign Up by email or Select Mobile Number

3. Select the correct country code +1, input your mobile number and click on “Get code”

4. A code will be sent to the mobile phone number, input the verification code and continue.

.

D:  Add Device on Mobile Phone APP (XMEye Pro)?

Steps:

–>1. Please connect the NVR/DVR box to your Router via Network Cable; (Some customers think it can support WIFI connection, while wired systems only support wired router connection, and have to be wired to router via ethernet cable)

–>2. Go to Monitor UI Interface, and Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR/DVR is online (Please skip step3),

–>3. If the cloud status shows “Probing DNS”, Please Navigate to “Main Menu > Network > Check the icon of “Enable DHCP”–>Apply;

–>Reboot the DVR by unplugging the power adapter and re-plug it, then double-check the cloud status ( only cloud status shows )

–>4. Go to your TV Monitor, navigate to “Main Menu–>Advanced–>Version”–> You will see the serial number.

The QR code contains Serial number info. We need this information after we add the device to mobile phone APP

–>5. Open the mobile APP “XMeye Pro” and register an account by your email first

–>6. Click”+” to add device–>Choose “NVR”

Device Serial Number: Click the “Scan” icon to Scan QR Code On the NVR UI Interface (Main Menu–Advanced–Version), (QR code contains username and password)

No need to input the username and password manually.

And click “OK”, and go back to the Device page on App,and you will see the device shows status:online ,

E:  How to enable Alarm Notifications on APP XMEye Pro?

1.Make the Alarm setting is already set on Monitor UI Interface

2. Please right-click mouse and navigate to “Main Menu–> Alarm–>Motion Detect/Human Detect/Face Detect–> Enable “Mobile Reported”–>click “OK”

(Default Setting is for Channel 1, Please select “All” channels.)

2.Open “XMeye Pro” mobile App, and navigate to “Event–>Device (the one you named)–>Enable “Allow Notifications”

.

F:  Configure Offline Camera or Add a New Camera?

—>1. After connect the camera to NVR via network cable, if the camera power on properly, the camera’s indicator light should be blinking.(see picture attached)

.

When you cover the camera’s photocell or put the camera in dark place, the infrared LED should turn on red color.

—>2. If camera powered on properly please follow below instructions.

1.Right-click mouse navigate to “Quick Setup(or Channel Set) –>Cancel

2. In the second box, if any camera status is offline or not connected, please select it and click ”Delete” first

3. Click “Search”, can you see new IP address showed on the topper box?

4. Select the IP address in topper box and click Network–>Auto Assigned–>OK

5. If auto assigned successfully, please click “Add” to add the camera.

.

.

G:  No Video Display on TV Monitor Or Blank Screen?

My UI Interface shows “No signal” or “Black Screen” ？

We need to divert this issue into two situations:

1.NVR Indicator light is on:

(1) Cause: The camera system’s video output resolution is 1080P. If your TV monitor resolution is below 1080P, this issue will occur.

Steps:

Please right-click and hold your mouse for over 10 seconds to see if the system can reboot or not. Or, please try to connect the system to another TV monitor with a higher resolution (above 1080P)

.

(2) Cause: The hard disk drive inside of the DVR box is broken, and use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is having an issue, and needs a replacement, plz contact email love@hiseeu.com for replacement HDD

After steps, if the thing still cann’t be resolved, which means the NVR box is broken, plz contact email love@hiseeu.com for replacement NVR box if their warranty is still 1 year

.

2.NVR Indicator light is off:

(1) Cause: The power adapter 52V 2.5 A connected to the NVR box is broken

Step: Use another power supply 52V 2.5 A to power on the NVR unit to have a try ( If you do not have a spare one, can contact us to buy a new one or we send you a new one if your warranty is still under 1 year )

.

(2) Cause: The hard disk drive inside of the NVR box is broken Step: Use the screwdriver to open the NVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the NVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is broken, and needs a HDD replacement, plz contact email love@hiseeu.com for replacement HDD

.

H:Why DVR/NVR can’t record or playback video?

.

If HDD(Hard disk drive) is having issue or something wrong with record setting, the DVR can’t record/playback the video

.

1.Check if the hard drive status is normal or error

Navigate to NVR/DVR Monitor UI Interface: Navigate to “Main Menu–>Advanced–>HDD info”

If status shows “Error” or No hard drive info , which means the hard drive is broken. (need to replace hard dirve)

2.Check the record plan is set up for 24/7 continuous recording

Navigate to “Main Menu–>Record Conf”

Channel : select “All”

Period: “00:00-24:00”

Select “Regular”

3. Please make sure the HDD was set up to “Overwrite”. (if it was set to “stop”, the system would stop recording when the storage is full)

Navigate to “Main Menu–>General–>Storage Full”

Add Device on Guard Station PC Client Software

Add device to “Guard Station” Download link: https://www.dropbox.com/sh/jeftu4sqwy4y1u8/AAD4PkyEJxg6j4H1n20PxBkZa?dl=0  

.

Please sign up for the mobile APP(Guard Viewer) account and add the device first.

Download and run “Guard Station” on the PC

1) Please Navigate to “Device Management”> “Cloud Device”> Click on “Login”

2) Login with your APP account and password.

3) After Login, the device you added to the APP will list here

Please click on “Control Panel”> “Live View”> Double-Click Camera to load the live view video

Add Cameras to NVR or PoE Switch (Router)

Add Cameras to NVR/ PoE Switch or Router

1. Add camera via NVR PoE Port

• If the camera is connected to NVR PoE port directly, the IP address

range should be modified to “172.16.0.X” (X is between 2 to 255)

Please right-click mouse and navigate to Camera

For brand new camera (password is 123456 by default), NVR will detect

and add camera automatically.

If the camera’s user name or password has been changed, you are required to input the info manually.

Move the mouse to the status icon , you will see the error message. “Offline [incorrect Username to Password]”

Please click on the edit icon to input password manually and click on “OK” to continue.

2.Add Camera to NVR via PoE Switch or Router

NVR will detect the camera under the same WLAN and list IPC here

• Click on plug icon to add the camera. If the camera has default user name: admin, password: 123456.

NVR will add it automatically.

• If the camera’s password has been changed, please click on the setting icon to modify the info.

• In this situation, the camera IP address range should be the same as NVR’s IP range

(You can check NVR IP by navigating to Network>Basic> TCP/IP). If not, please contact the technician to modify the camera’s IP first.

Camera Not working

Camera not working?

1.(Port issue) Insert the camera to another port of the NVR to have a try, and wait at least 5 minutes

2. (Camera issue) Make sure if the camera infrared light will turn on red or not in the night time

3. Also plz right click your mouse to “Menu-Camera”, and take a photo of this whole page and send it to us

（Check how many cameras are discovered）

Also go back to the home screen and Check connection status, to see if it shows” Network disconnected” or “incorrect user name and password”

Device Offline on APP or NVR?

Device Offline on APP or NVR?

If the device shows offline on mobile phone app  “Guard Viewer” , we need to make sure the NVR is connected to network perfectly or not

Go next to your Monitor that connected to NVR, and check out the network status

first navigate to this path first : “Menu–Network–Basic–P2P” , also check the device status is online or not,

if it shows: network disconnected, plz enable the DHCP in this path ” Menu–Network–Basic-TCP/IP ” and click “Apply” . After that, go back to “P2P” and check if the device status is online or not

Also , please make sure the PPPOE needs to be disabled, plz navigate to “Network–Advanced–PPPoE”

Enable Alarm light on Each Camera?

Enable Alarm light on Each Camera?

.

(Alarm light would only work during the night time when the alarm was triggered)

.

1. Set up the Alarm light First Right-click your mouse to “Menu– VCA — Intrusion Detection/Crossing Line Detection– Triggered Actions” , and draw the rules for the alarm type

After you set up an alarm type (Like”Intrusion Detection”, or “Crossing Line Detection”), Click on “Alarm Linkage”, you will have the option to Enable “Alarm Light” (Spotlight is only Available During the Night)

2. Enable Alarm Light on “Triggered Action– Alarm Light” for each channel, and Click “OK”

Forget NVR Password？

If you forget your current password, please follow the instructions to reset it.

1. In the system login interface, please click on “Enter Password” > “Forgot Password”

2.If you filled in your email address as a reserved email when you set up the system, you can reset the device password via the APP(Guard Viewer) by navigate to “Me–General–Forget Device Password”

3.Scan the above QR code by app and the security code will be sent to your email address.

4. Enter the security code from email to reset the password

Additionally, If you the email doesn’t belong to you, plz contact us at love@hiseeu.com for more support

Add Device to APP(Guard Viewer)

.

Auto add is not suggested. Please tap on “Later” if you see this message box.

.

In this situation, it will Auto Search to discover the NVR device connected to the local network. But once your mobile phone disconnects with LAN WiFi, you will not be able to view it anymore.

Please Add devices in this way

1.  Please Tap on “ Menu” icon> Tap on “Devices”> “Add”,

2. Tap on “Scan”> “OK” to scan the NVR QR code

3.Navigate to “Menu– Network> Basic> P2P”

• If the Device Status is “Network connected…” , means device is online   and ready for remote view

• If the Device Status is “Offline” , please check the network connection first, if the problem remains, please feel free to contact us at Love@Hiseeu.com   

After you add the device successful, the “Device status” will be “Online”, and your APP account username will display here.   • You can check your APP user name by navigate to “Me”

• If the username doesn’t belong to you, please click on “Delete” and add it again.

4.Add NVR by scanning device QR code and click on “save”

5.   Please Tap on “Menu ” icon, Tap on “Live View” “Add”

6. Select the device and tap on “Start Live View”

Human Tracking/Detect for Model PK-4YHD985-CT ?

1.To enable human tracking , Set preset point “21”. Here is the video link for your reference: https://www.amazon.com/live/video/07adae4ec34a47618bd754cc6c1f8966?ref_=dp_vse_ibvc1

2.To enable human detection, plz go to this path “Menu–Alarm-Motion” , and choose the camera you want, to enable it

(This doesn’t support customize area)

No Video on TV Monitor or blank Screen?

.

The camera system video output resolution is 1080P, if your TV monitor resolution below that will occur this issue.

.

If possible, could you please try to connect the system to another TV monitor with a higher resolution(above 1080P).

Or, please hold your mouse wheel over 10seconds to see if the system can reboot or not.

If not, plz contact us for further support

How to share Device to others via APP Guard Viewer?

.

One device linked to One User ONLY. The NVR system ONLY can be controlled by one authorized account, who can share the device with others in order to prevent attacking or hacking.

For admin user, please follow the instructions to share the device with others:

.

1.Type on “Menu Icon ” and navigate to “Devices”

.

2.Tape on “… ” > “Share”, You can select a single channel to share or select the entire NVR system to share

(1) Share device by typing in the user name you wanted to share with and selecting function as needed.

• The other user needs to register a Guard Viewer APP account and provide the user name for sharing.

• After that, when this user login the APP will find the device by navigate to “Devices”

(2) Share device by generate a QR code

• Create a sharing password and set the valid period

• Click “Generate”, your APP will generate a QR code

• Other users can use the APP to add the device by scanning the QR code you sent

Download the mobile APP and Sign up for an Account

.

1. Download and install the app.

Please scan the QR code to download the free APP “Guard Viewer”

You also can visit the Apple Store or the Google Play Store to download the Guard Viewer app for iOS or Android devices. Alter installation, tap the icon to launch the app.

2.Register an account and login

For first time use, please create a new account and add the following steps:

Please tap Sign up and follow the on-screen prompt to register an account by email.

<p>The post Hisseu PoE Camera System User Guide v1 first appeared on NVR IPCAMERA SECURITY.</p>

Our products and solutions have been deployed and used daily in more than 100 countries and regions, meeting customer needs in various vertical markets that range from residential to commercial, from healthcare to public safety.

Reset Device Web Password on Akuvox Cloud Platform

Users may forget passwords for logging into device web interface. Follow the steps to reset the web password when the device is connected to Akuvox Cloud.

Step 1

Log into the Akuvox Cloud platform with an installer account.

Step 2

To go to the device Info page, follow the steps.

On the Single-tenant Manager view

1. Click User on the left column.

2. Click the Device icon of the desired user.

3. Click the Info icon of the desired device.

On the Project Manager view

1. Select Community or Office on the left upper corner.

2. Click the Info icon of the desired community or office.

3. Click Intercom Devices and then the Info icon of the desired device.

Step 3

1. On the device Info page, click the Settings button.

2. On the Settings page,

Note

Factory Reset Akuvox Devices v2

Reset Door Phones through Physical Buttons

Note

Power up the devices before resetting them through the physical buttons.

S539, S532, X916 and X912

Hold the reset button with a pin and the device will be reset.

X915, E12 and DB01

Insert a PIN into the hole and hold it to reset the device.

E16, E18, E20 and E21

Remove the back cover of the door phone and hold the reset button to reset the device.

R27, R28, R29 and R20 Series

R27, R28, R29, and R20 series do not support resetting by pressing physical buttons.

Watch the video for other reset methods.

Reset Intercom 2-wire Kit Accounts for Single Tenants

Through resetting, the tenant information will be deleted while the device information will be retained after a tenant moves out. This saves time from repeatedly entering the device information.

Installers

1.Log into the SmartPlus Cloud platform with an installer account.

2.Click Role in the upper right corner to switch between single-tenant and community projects.

3.Click to reset the target user account.

After resetting, the following data will be reset:

The following data will be kept:

The following data will be removed:

Distributors

Distributors can reset the Kit users when the Kit is added directly to the single-tenant projects under the distributor account.

3.Click  to reset the target user account.

After resetting, the following data will be reset:

The following data will be kept:

The following data will be removed:

End Users

End users can delete the family master account on the indoor monitor.

After resetting, a new QR code will be issued to the indoor monitor from the SmartPlus Cloud.

On the SmartPlus Account screen, tenants can scan the QR code to register SmartPlus accounts themselves.

.

How to Configure and Modify the Password

The initial password “admin” is rather weak, easy to crack, thus we provide for you the password change service.

Before Start

The difference between the user mode and admin mode on the web page

How to configure

Website password modification

admin mode
Go to Security >Basic >Web Password Modify, choose user name as “admin”, click Change Password, then enter the old password “admin”, input the new password.

user mode
Go to Security >Basic >Web Password Modify, click Change Password, then enter the old password “user”, input the new password.

Device password modification

System code
System code is used to enter “More Interface”, to adjust the password: More>Settings>More, input the default system code “123456”, tap System Code, input the original system code and new system code.

Setting code
Setting code is used to enter “Settings”, and it is left blank by default. To adjust the password: More>Settings>More, input the default system code “123456”, tap Settings Code, leave the original settings code blank, input the new one.

Steps to Enter Device Web Interface

.

Factory Reset Akuvox Devices

Reset Device Web Password on Akuvox Cloud Platform

Users may forget passwords for logging into device web interface. Follow the steps to reset the web password when the device is connected to Akuvox Cloud.

Step 1

Log into the Akuvox Cloud platform with an installer account.

Step 2

To go to the device Info page, follow the steps.

On the Single-tenant Manager view

1. Click User on the left column.

2. Click the Device icon of the desired user.

3. Click the Info icon of the desired device.

On the Project Manager view

1. Select Community or Office on the left upper corner.

2. Click the Info icon of the desired community or office.

3. Click Intercom Devices and then the Info icon of the desired device.

Step 3

1. On the device Info page, click the Settings button.

2. On the Settings page,

Note

.

Check IP Address of Akuvox Door Phones

IP address(es) can be obtained on Akuvox door phones. With the IP address, you can log into the device web interface for configuration, troubleshooting, and more.

Devices with Numerical Keys or Touch Screens

Check the IP address on the system information screen.

Devices without Numerical Keys or Touch Screens

Check IP address through automatic IP announcement.

Note

You can also obtain the device’s IP address using the Akuvox IP scanner.

Download IP scanner:
https://knowledge.akuvox.com/docs/akuvox-ip-scanner?highlight=IP

Check IP Address of Akuvox Indoor Monitors

IP address(es) can be obtained on Akuvox indoor monitors. With the IP address, you can log into the device web interface for configuration, troubleshooting, and more.

The routes may vary by model.

In this part, C313 is taken as an example.

Exception

To check the IP address of S560, press the # key for about 5 seconds and the device will automatically broadcast its IP address.

Check IP Address of Access Control Terminals

Obtain IP Address via IP Scanner

IP scanner allows you to search the device IP address(es) and to perform targeted device reboot, reset, network setting, etc.

Note

Installation

1. Decompress the rar. file downloaded.
2. Double-click on the setup.exe file.

3. Go through the installation process.

a. Click Next to start the installation.

b. Check to accept the terms of the license agreement, and click Next.

c. Enter User Name and Company Name, and click Next.

d. Click Finish to install the IP scanner successfully. The software icon will appear on the desktop.

Obtain IP Address

Note

To obtain the device IP address, your personal computer should be in the same LAN as the device.

Additional Features

Apart from checking IP address(es), you can export device information and perform targeted device network settings and web interface access, reboot, and reset.

Note

Before applying the following changes, enter the User Name and Password. The default is admin.

Log into Device Web Interface

Enter the device IP address in a browser, and you can log into the device web interface for configuration, troubleshooting, and more.

.

<p>The post Factory Reset Akuvox Devices v2 first appeared on NVR IPCAMERA SECURITY.</p>

Troubleshoot Offline Camera

Troubleshoot Offline Camera

Learn how to troubleshoot when a new Verkada camera is offline

Updated over a week ago

Use this article to read through some common scenarios and try the suggested troubleshooting tips to help. If you still need help, please contact Verkada Support.

What is the LED status of the camera?

Camera has been solid orange for over 10 minutes

Camera is blinking blue for over 5 minutes

Camera is solid blue for over 5 minutes, says “waiting to be connected on Verkada Command”

Roles and Permissions for Cameras

Roles and Permissions for Cameras

Learn about the roles and permissions available for Verkada Cameras

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Cameras.

Org-level roles

Organization-level roles are configured on a per-user basis. Groups cannot be used to set organization-level roles.

Below, click the down arrow to the left of the role to learn more about the role and access.

Org Member

Org Admin

Verkada Cameras Troubleshooting 2024

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

CP52-E PTZ permissions

The CP52-E PTZ camera permissions determine who can manage the Sentry Mode feature.

Permissions model (example)

Here’s a simple example of a permissions model that a typical organization with several sites and users may employ:

Users and their required level of access

Permissions each user should be assigned

.

Set Org Admin permissions

Revoke Org Admin permissions

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Customize roles and permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

Roles and Permissions for Command

Roles and Permissions for Command

Learn about the roles and permissions available to Command users and groups

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Command. It also explains how to customize roles and permissions.

Permission levels

Permissions are set at the following levels:

Daha fazla göster

Permissions considerations

Common user permission configurations