Intro

You’re Not Alone

Installation can be hard. We’re happy to talk it over with you or take over a DIY project that you’ve realized needs professional installation. Our support hours are from 9AM-7PM Monday – Friday (EST) and we are available via chat, email, phones, and remote PC screen-sharing, if you need any help. You can reach us at 866-414-2553.

Disclaimer: The laws governing cable and wire installation can vary from state to state and sometimes even counties and cities pass specific, unique laws regarding cabling; these state, county and city laws are too complex for us to explain. This page is not a how-to installation guide, as we cannot keep up with local laws.

Although we now offer installation, locally, we started as a DIY-only company, and we primarily serve those adventurous types who want to run the cable for themselves. Even so, we get asked about do-it-yourself installation all the time…. We wanted to post a few of our standard answers here.

Part 1

Don’t Start a Fire or Shock Yourself

Electricity Can Kill You; Avoid Electrical Lines!

Never strap, staple or otherwise run networking cable to conduit or raceways carrying electrical current. Never run any cable within 2 inches of Class I electrical lines, lighting, fire alarm, or power lines or devices.

Give a Wide Berth to High Voltage Devices or Lines

Never run any cable within 6 feet of a conductor or fuse box. A minimum 5-inch distance is required from any fluorescent lighting fixture or power line over 2 kVA and up to 24 inches from any power line over 5 kVA. If unsure about the a device or line, consult an electrician. Route cable away as far as you can from large motors, generators, induction heaters, arc welders, x-ray equipment, and radio frequency, microwave or radar sources. NEC/NFPA 70, Article 800-52

Protect it from Future Physical Damage

You might want to put a nail or screw in later and don’t want to puncture your cables, so when a cable, raceway, or soft conduit (anything you can puncture) is installed parallel to framing members (joists, rafters, or studs), furring strips, or crown molding, keep the cable at least 32 mm (1.26 inches) from the edge. NEC 300.4(D)

Don’t Leave it Dangling – Secure Your Cables

You can connect cable directly to a surface with straps, staples, cable ties, hangers, or similar fittings, but you have to secure it somehow. NEC 800.24; 300.11

Use Plenum rated cable in Areas with Airflow

If you are going to run cables through an area which is used by your heating, air circulation, or air conditioner systems (such as above a drop ceiling in an office), you must use Plenum rated cables, which have a special insulation that has low smoke and low flame characteristics. When securing cable in Plenum required areas, make sure your straps, cable ties, and similar fittings also are plenum rated. NEC 830; NFPA 90A

National Rules – Consult your local laws

These guides are meant to familiarize our clients with the national requirements as expressed in the National Fire and Alarm Signaling Code and the National Electrical Code. Your state or local laws may differ. If you live outside the USA, consult your governmental laws. Don’t consider this your only resource.

Turn the Breaker Power OFF

Any time that you will be drilling or cutting into your wall, you want to turn the power off. You don’t want to drill into a hidden electrical line. You probably already know this, but our lawyers insisted.

Wear Safety Goggles

Any time that you are drilling, you want to wear safety goggles and hearing protection, like ear plugs.

Security Camera Installation Guides v2

Part 2

Drilling through Different Materials

Sheetrock (most interior walls)

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of sheetrock.

Wood

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of wood.

Stucco

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of stucco.

Brick and Masonry

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of brick.

Concrete

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of concrete.

Metal Siding

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of metal siding

Part 3

Running the Cable

Basic Cabling

Terminating Cable (Putting the ends on)

Instructions for putting the RJ45 ends on to ethernet (for example, Cat5 / Cat6 / Cat5e) cable.

Using Our Waterproof Connectors

When installing a camera outdoors, it is imperative that you put our waterproof RJ45 Connector on the ethernet (for example, Cat5 / Cat6 / Cat5e) cable.

No Protection – Just Running the Wire

You can connect cable directly to a surface with straps, staples, cable ties, hangers, or similar fittings, but the cable could get damaged and someone might be able to cut it.

24 Volt Wiring: PTZ

The Spotlight PTZ cameras uses 24 volt power rather than POE because it requires more power than is capable of Power-Over-Ethernet for its natural white light spotlight. The Laser can also be powered via 24 volt power and can be powered the same way, although it is not required to do so. This guide shows you how to wire these PTZs.

24 Volt Wiring: Sharpshooter

The Sharpshooter IP Bullet cameras uses 24 volt power rather than POE because it requires more power than is capable of Power-Over-Ethernet for its long range infrared. This guide shows you how to wire the Sharpshooter.

Protecting your Cabling

Liquidtight Plastic Tubing

Liquidtight plastic tubing is easier to work with than flexible metal tubing, but is less secure. It is also great for areas with lots of expected moisture as it won’t rust.

Flexible Metal Conduit (FMC)

Flexible metal conduit is difficult to cut (watch out for sharp edges), but easier than solid conduit to install.

Electric Metal Tubing (EMT)

Solid metal conduit is the most secure form of installation. It requires a specialty conduit bending tool.

Conduit Fill

This chart will let you know how many cable runs you can fit in one conduit pipe, depending on the size of the conduit.

Raceway (Outdoors) – Coming Soon

Raceways are most popular indoors to make the space look clean and professional. There are also outdoor rated raceways; this guide covers using raceways outdoors.

Clean and Professional Interiors

Raceway (Indoors)

Raceways are most popular indoors to make the space look clean and professional. There are also outdoor rated raceways. This guide covers using raceways indoors.

Ethernet Wall Plates

Not recommended. It can be difficult to find a wall plate that passes POE power and provides grounding. These devices also provide a secondary point of failure, and take up far more room than a cable pass through plate for larger systems.

Dealing with Long Distance

Using POE switches to reduce cabling

You can run one cable to a POE switch and then run several cameras to that switch, however, POE switches are not plug-n-play. POE switches do require you to know a decent amount about computer networking.

Cables run over 300 feet

Cat5e and Cat6 cable data has a limit of 300 feet, but if you need to go further than that you can use a POE extender, POE injector, or POE switch to hear and repeat the signal. This article discusses when you would use each of these tools.

Long Distance Wireless

Military-Grade Long-Range Wifi Solution are used when attempting to send wireless IP Camera video data more than 100 feet (and up to 3 Miles). These products will require a professional wireless network technician on location.

Part 4

Mounting Cameras and Recorders

Basic Camera Installation

Bullet Cameras on Walls

In this guide, we will be installing a bullet camera on a wall.

Bullet Cameras on Ceilings

In this guide, we will be installing a bullet camera on a ceiling.

Bullet Cameras on Soffits

In this guide, we will be installing a bullet camera on a soffit.

Dome Cameras on Ceilings

In this guide, we will be installing a dome camera in a ceiling tile.

Dome Cameras on Walls

In this guide, we will be installing a dome camera on a wall.

Positioning the Lens in our Dome Cameras

In this video guide, we demonstrate how to adjust the lens positioning on our Marshall, Guardian, Warden, and Mosquito Dome Cameras.

Audio and Alarm Inputs FAQ and Sample Wiring Guide

Here’s a guide on Line-Level Audio Inputs and Analog Wired Alarm Integration.

Attaching Our Camera Mounting Accessories

Electrical Mounting Boxes

Our electrical box mounts are used to give easy access to your connections, hide them inside the junction box, and allow you to drill a smaller hole in your wall. If you want to run conduit they are necessary to run conduit straight to the camera.

PTZ Wall Mount Bracket

This guide will show you how to mount your PTZ camera to the wall mount bracket.

Pole Mounts

In this guide, we will be installing a Hornet Pro bullet camera on a pole.

Pendant Mounts

In this guide, we will be installing a Radius panoramic dome camera on a pendant mount. You can install all our PTZ and a few of our dome cameras via Pendant mounts.

Screw Size Chart

Lose a screw? No problem. Here’s all our 2018 product line screw sizes in one convenient place.

NVR Mounting Options and Hard Drive Installation

Shelf / Desk Mounting NVRs

This is what most people do: just put it on a shelf or desk. This makes it easy to connect to a TV/monitor and use the mouse (included) to control the NVR.

Rack Mounting NVRs

Companies often want to put the NVR in their server rack room. People who do this often to control the NVR only through our apps or web browser. Only our larger NVRs (16 channels and up) are wide enough to be rack mounted (and they come with ears). Our smaller NVRs can use our Rack Mount Shelf.

Wall Mounting NVRs

Many people choose to mount their NVR on a wall near a TV. To do this, you will want to purchase a vertical rack, like this one that matches the height of your NVR. The 16, 32, and 64 channels units have a height of 2U and the 128 channel is 3U. NVRs are heavy and you will want to make sure your wall can support the weight.

Mounting NVRs behind a Wall / in an Attic

People who are afraid of the theft of an NVR often place it behind a false wall or in an attic. People who do this control the NVR only through our apps or web browser. Be aware: Not all attics are insulated well enough to be within the temperature requirements of the NVR. Temperature range is listed on each NVR’s technical specs tab.

“NVR” Lock Boxes

There’s a few companies advertising “NVR Lock Boxes,” but any Server Rack or Computer Rack will do. Most Server Racks or Mounts have locks on them already. This picture is of a Tripp Lite Server Rack with Lock It houses a 32 channel NVR, two of our POE Switches, and a router, but there are tons of companies selling small server racks online.

NVR hard drive installation

If you purchase both a hard drive(s) and recorder from us, we will happily install the hard drive for you. but here’s a handy guide if you want to do it yourself.

Part 5: Specialized Work

When to NOT DIY – Get an Expert

Long Distance Wireless

Military-Grade Long-Range Wifi Solution are used when attempting to send wireless IP Camera video data more than 100 feet (and up to 3 Miles). These products will require a professional wireless network technician on location. We can’t offer support on this product remotely, as once we can see it remotely, that means that it is already working.

Aerial Cable

Aerial cable clearance varies based on location (cable over a road needs more clearance than over a sidewalk, for example), needs to be enclosed within 8 feet of finished grade, and requires a on-site structural analysis to make sure the cable won’t break. Hire an expert.

Burial of Cable

Number one, call 811 before you ever dig: know where your power company has buried its power cables! The required cable burying depth also can vary based on your local zoning laws and your certificate of occupancy; you should get an expert.

Elevators

Don’t even try to install any cable in one without a licensed elevator technician’s help as the cable needs to be inside the cable traveler. An error in securing the cable can result in damage to the elevator’s operation – and potentially the people inside it. Don’t mess with it; get a licensed elevator technician to run the cable.

<p>The post Security Camera Installation Guides v2 first appeared on NVR IPCAMERA SECURITY.</p>

Troubleshoot Offline Camera

Troubleshoot Offline Camera

Learn how to troubleshoot when a new Verkada camera is offline

Updated over a week ago

Use this article to read through some common scenarios and try the suggested troubleshooting tips to help. If you still need help, please contact Verkada Support.

What is the LED status of the camera?

Camera has been solid orange for over 10 minutes

Camera is blinking blue for over 5 minutes

Camera is solid blue for over 5 minutes, says “waiting to be connected on Verkada Command”

Roles and Permissions for Cameras

Roles and Permissions for Cameras

Learn about the roles and permissions available for Verkada Cameras

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Cameras.

Org-level roles

Organization-level roles are configured on a per-user basis. Groups cannot be used to set organization-level roles.

Below, click the down arrow to the left of the role to learn more about the role and access.

Org Member

Org Admin

Verkada Cameras Troubleshooting 2024

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

CP52-E PTZ permissions

The CP52-E PTZ camera permissions determine who can manage the Sentry Mode feature.

Permissions model (example)

Here’s a simple example of a permissions model that a typical organization with several sites and users may employ:

Users and their required level of access

Permissions each user should be assigned

.

Set Org Admin permissions

Revoke Org Admin permissions

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Customize roles and permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

Roles and Permissions for Command

Roles and Permissions for Command

Learn about the roles and permissions available to Command users and groups

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Command. It also explains how to customize roles and permissions.

Permission levels

Permissions are set at the following levels:

Daha fazla göster

Permissions considerations

Common user permission configurations

Daha fazla göster

Roles and permissions by Verkada product

.

Org-level roles

Org-level roles are configured on a per-user basis. Groups cannot be used to set org-level roles.

Org member

Org Admin

Access Control Role

.

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

Access Site Admin

.

Customize Roles and Permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

FAQ

Why has my organization disappeared?

Why are cameras missing from my organization?

Why can’t I access certain features or settings, such as other users?

Resolve Issues with Missing Cameras

Resolve Issues with Missing Cameras

Learn how to resolve issues when cameras are missing from your Verkada account

Updated over a week ago

When you log in to Verkada Command, you can only access cameras and video in organizations or sites where your user account has permissions.

Note: Even if you are an Org Admin, you still need to grant yourself permission to view all sites. Learn more about roles and permissions for cameras and Command.

If you log in to Command and cameras are missing or have disappeared, always check user permissions. The most common reason cameras are not visible is that your user account needs permissions to the site(s) where the cameras are configured.

Common reasons that can cause cameras to disappear

Check permissions

If you are an Org Admin, you can check and correct your own permissions:

Resolve Issues with Night Mode

Resolve Issues with Night Mode

Common issues with IR and Night Mode with steps to resolve them

Updated over a week ago

Each Verkada camera has night vision capabilities, using a sensor to detect low-light situations. When external lighting is low, the camera switches to night mode and records in black and white, using infrared (IR) LEDs to illuminate the environment. If the IR is emitted improperly through the dome or reflected into the lens, it negatively impacts image quality.

Common night mode issues

It is imperative that the dome remain free of debris and the camera is installed properly to achieve the best image quality. When viewing footage in night mode if the footage appears obscured it is most likely the result of one of the following scenarios:

Camera always in night mode

If your camera is always in night mode even where there is sufficient light in the environment the lux (light) value may need to be adjusted. If this is the case, reach out to Verkada Support for further assistance.

Environmental obstruction

If the camera is mounted too close to a wall, ledge, or light source, the image quality may be degraded due to IR reflection.

Recommendation. Ensure that cameras are mounted sufficiently far away from surfaces that may cause the IRs to reflect, such as light sources.

IR obstruction

If a first-generation Dome camera (D30 or D50) is operating in night mode when there is plenty of light, the IR sensor is likely obstructed by the camera housing.

To fix the obstructed light sensor, physically rotate the lens barrel assembly 180° so the sensor and IRs are visible through the camera case.

Example: Proper and improper orientation

Note: After rotating the lens barrel, the camera orientation may need to be changed in Command.

<p>The post Verkada Cameras Troubleshooting 2024 first appeared on NVR IPCAMERA SECURITY.</p>

TetherX Camera Setup Guide v2, Tether your video surveillance, alarm panels, network infrastructure and other IP or Serial devices to the cloud. Monitor the health of your sites, cloud record cameras and integrate with third party services.

The steps required to set up Samsung Cameras / DVRs and NVRs

Setting Correct Profiles

Please ensure you have 2 profiles configured on your device:

IP Cameras

Cameras are the easiest to set up and should work out of the box. If the cameras are not working for any reason, please try one of the following for the Analytics Path and Recording Path:

Multi-Sensor IP Cameras & Encoders

If your device is a multi-sensor camera or an encoder, please set the Analytics Path as follows:

NVR – Network Video Recorders

DVR – Digital Video Recorders

DVR recorders setup is similar to NVR setup with the following differences:

.

Can I use TetherX alongside HikConnect?

Can I use Hik-Connect on my Hikvision cameras and recorders?

Yes.

Please make sure that stream encryption is switched off under Configuration > Network > Advanced Settings:

HikConnect stream encryption uses a proprietary mechanism which is not available to third-parties. Please note TetherX will encrypt the stream to the highest standards, for more information please see our security white-paper.

Note: If you are still getting a broken stream or no live view, please try updating the camera and/or recorder firmware to the latest. There are known issues that have been addressed by Hikvision.

.

Live View – Technical Implementation Details

How TetherX implements live view to be compatible with all manufacturers

Introduction

The quality, latency and smoothness of live view streaming is dictated by many factors:

Available Streams from Cameras

Typically cameras will provide 2 video streams as well as the ability to request a single image. These limitations dictate what is and isn’t possible when it comes to both recording and streaming.

💡 Note: More expensive and speciality cameras will provide additional video streams and custom streams of crops/de-warps of the same image (e.g. 180 or 360 cameras).

The streams are usually accessed through RTSP and the images through HTTP. For example:

Formats

Transcoding vs Proxying

TetherX supports both transcoding and proxying/packaging. The differences between the two are as follows:

Transcoding is a process of taking the stream from a camera, decoding it and then re-encoding it into a different format. This is the ideal method to hit a specific requirement of Internet bandwidth and viewing size, but it is in most cases cost prohibitive as you need power hungry and expensive hardware to achieve.

​For context, a TetherBox Pico capable of recording 10 cameras will only be able to record 2 if transcoding (you can enable transcoding in TetherX by editing a camera and switching to the advanced tab).

Proxying & Packaging is what is used in most cases, where the original video stream is maintained but is packaged into different containers, for example .mp4 for video recording and .ts for local and high-def live streaming (see streaming technologies below).
​

This means that ultimately, you are at the mercy of the camera/recorder. If you need to open 16 cameras and each one is 1mbit, but your upload speed is only 10mbit, it will simply not work because the stream size cannot be adjusted without either:

Video vs Images

TetherX use a combination of images and video to achieve different goals. It is important to understand the differences and advantages/disadvantages of each, which in turn dictate when either is used in TetherX.

The main difference between image and video compression is every image is self contained, where every video frame is part of a stream. While you may skip an image, skipping a frame in a video stream leads to parts of the image breaking / disappearing:

Systems that ignore broken/skipped data (e.g. streaming over UDP) will show a broken image while many systems will simply show a loading spinner while they wait for the next key frame (which is controlled by the key-frame interval set on the camera/recorder, typically set to 1 second, or the same number as fps, but sometimes much longer).

Because each image is self contained, it is typically 5 to 25x larger in bitrate vs video at 25 images per second. It may initially seem obvious that video should be used when accessing remotely, however there are certain important underlying trade-offs that make it a much tougher question which needs to be evaluated on a case by case basis, according to the following:

Advantages of Images

Live View Streaming Technologies

TetherX uses all mainstream streaming technologies available and choses between them depending on the specific requirements and constraints:

How TetherX Does It

TetherX supports most streaming technologies and switches between them depending on context.

When local streaming (the TetherBox is able to detect if you are on the same network), if we are viewing less than 10 cameras simultaneously TetherX switches to LHLS (see above) to show the primary video stream from each camera at full resolution/frame-rate (assuming your viewing device is capable of displaying this many streams). If this is not working well for you, you are presented with a toggle to switch off High-def streaming to fall back to loading images.

When full screening a camera (double tap/click a camera), we assume you want the higher quality and we switch to the full primary stream. If your connection is not able to sustain this stream, we automatically fall back to loading images.

When viewing multiple sites / cameras over Internet in record mode, we switch to image viewing but we transcode/transize the images depending on the size of each live view box on your screen. This ensures that you are able to view many simultaneous cameras, the latency is lower than video, it automatically adapts to the available bandwidth and it does not impact recording quality. This does however mean a lower fps.

When viewing multiple sites / cameras over Internet in monitor mode, we proxy the connection directly to the image provided by the camera. This leads to a further lowering of fps but ensures the TetherBox can monitor the health of and provide live view of 10x more cameras than in record mode.

Learn more about using Live View in TetherX here.

How Hikvision iVMS Does it

Because of the constrains outlined above, in order to show smooth video in iVMS (and Dahua PSS) software, if the connection speeds both on site and viewing device cannot accommodate the streams, the software temporarily reconfigures the cameras to send a lower bitrate stream while keeping the resolution the same.

💡 Note: if you happen to kill the software at this point (or lose connection), this can cause the camera to permanently record in lower quality.

Because many cameras or recorders only support a single stream at above D1 resolution, this means that not only is the live view quality reduced, but also the video being recoded which can lead to losing critical video evidence.

In our testing, limiting the connection to 5mbit 200ms upload and streaming just 4 cameras in HD resulted in blocky and usable footage being recorded on the NVR. It also took over 10 seconds to get an initial image, however the motion was smooth (25fps) once loaded.

In comparison when using images (outside of the iVMS/PSS software), the images loaded almost immediately, the image quality was significantly higher, but the frame-rate was poor (3-4fps) – still sufficient for making decisions in a control room setting, but understandably disappointing in smoothness by comparison. (Note: higher fps can still be achieved by full screening a single camera on demand).

When viewing a smaller number of cameras from the same manufacturer on a single PC or phone, it looks impressive to have smooth 25fps video on iVMS/PSS/others. However, when dealing with 100+ or even 32 cameras, from different manufacturers, different firmware versions, with multiple users, across multiple sites, with differing and fluctuating bandwidths, you begin to appreciate the trade-offs and advantages/disadvantages of each approach.

💡 Note: This approach of custom code to adjust Hikvision camera settings to achieve smoother live view is only suitable if you do not care about recording quality and you are optimising for a single manufacturer with compatible models/firmware.

​TetherX is an open platform with a focus on convention over configuration, we prioritise the integrity of recorded footage above live view and we implement approaches that work across all recorders/cameras as well as viewing devices.

.

Uniview / UNV Camera Setup Guide (for use with TetherX)

Using TetherX with Uniview / UNV Cameras

Summary

Uniview or UNV cameras should work out of the box in most cases. However please note depending on the age of the camera and firmware versions, the RTSP path may be different.

Please try the following paths:

3. Open the Advanced tab and enter the required Analytics Path and Recording Path. Please try all the paths given as examples above.

.

Camera Setup Checklist

Adding IP cameras to TetherX Please note your camera may have a different interface and options may be located in a different part of the interface. Please refer to the camera manual if you are not able to find the relevant option.

Network

Set a Static IP

Set camera to unused IP on 192.168.88.x network
set DNS/Gateway to 192.168.88.100

Important: Although it’s possible to configure your camera with DHCP, and TetherBox is capable of detecting any IP changes, we strongly advise against this practice for security reasons. This setting can potentially allow the camera to connect directly to the internet, raising a range of security issues. These include unauthorised access through back doors, or the risk of security holes in the camera’s firmware if it’s not updated regularly.

Video & Audio

Recording Stream (primary)

Analytics Stream (secondary)

Conditions

.

Audio (optional)

Date & Time

One option is to disable time from being displayed in the camera at all. You generally do this under OSD settings. If you do wish time to be displayed in the image, you need to set the following:

<p>The post TetherX Camera Setup Guide v2 first appeared on NVR IPCAMERA SECURITY.</p>

.

As a world-leading video-centric AIoT solution and service provider, Dahua has a lot in store for us in terms of making camera installation simple, quick and user-friendly. Its recently launched 5E initiative focuses on user-centered design and aims to provide customers with efficient operations, cost reduction, security guarantees, and value enhancement. Easy Installation, one of Dahua 5E’s key components, refers to easy hardware installation and easy software deployment. For hardware, Dahua constantly optimizes their structural design, tools requirements, guide materials, process safety, etc., so as to improve the hardware’s ease of installation. For software, Dahua continuously optimizes their accessibility, flexibility, complexity, and correctness, thus enhancing the easy installation of software products.

.

Here are some of the highlights of Dahua 5E’s Easy Installation:

.

Dahua PTZ

.

.

Pain Points:

.

.

Solutions:

.

.

Application Scenarios: retail store, villa

Dahua Easy Installation Manual v1

Also Read : DAHUA IP Camera 5.0 UI Setup

Dahua Easy Installation Manual v1.

Dahua IPC

.

.

Pain Points:

.

.

Solutions：

.

.

Application Scenarios: cafe, parkland

.

Dahua ITC Cardan Bracket 8019

.

.

Pain Points:

.

.

Solutions:

.

.

Application Scenarios: highway, urban roads

.

HDCVI

.

.

Pain Points:

.

.

Solutions:

.

.

Application Scenarios:

.

.

What is Symmetric Encryption Algorithm?

.

In the modern stage of cryptography, the concept of key secrecy was introduced, giving rise to a new encryption algorithm paradigm called symmetric encryption algorithm.

.

Symmetric encryption algorithm, also known as single-key algorithm, is characterized by the use of an identical key for both encryption and decryption. They can be broadly classified into two major types: sequence ciphers (also known as stream ciphers) and block ciphers.

.

The core of stream cipher encryption is the key (also known as the seed key) that goes through a key stream generator to produce a key stream. This key stream is then XORed with the plaintext byte stream to obtain the ciphertext byte stream, encrypting one bit or one byte of the data stream at a time. The encryption process is illustrated in Figure 1.

.

.

Figure 1: Steam Cipher Encryption/Decryption Process

.

The core of block cipher encryption is to divide the plaintext data into fixed-length blocks and encrypt them using a key, resulting in ciphertext blocks. The plaintext is encrypted on a byte-by-byte basis. The process is illustrated in Figure 2.

.

.

Figure 2: Block Cipher Encryption/Decryption Process

.

Block cipher encryption is achieved by grouping the plaintext. To enhance the security in the encryption process and facilitate grouping, two key points are usually considered: encryption modes and padding modes. As for the specific selection of encryption mode or padding mode, it often depends on practical application scenarios, required security strength, and other factors.

.

The introduction of encryption modes mainly considers whether there should be any correlation between different blocks or whether each block should be encrypted independently. Different encryption modes represent different iteration methods used in the encryption process of plaintext blocks. Table 1 provides the advantages and disadvantages of using different encryption modes.

.

.

Table 1: Comparison of Several Encryption Modes

.

The introduction of padding modes mainly addresses the issue of plaintext that is not a multiple of the specified block size. In such cases, the remaining bits need to be padded to match the algorithm’s specified block size. During encryption, the plaintext is padded, and during decryption, the padding needs to be removed according to the same padding mode. Table 2 presents several common padding methods in block ciphers.

.

.

Table 2: Comparison of Several Padding Methods

.

Symmetric encryption algorithms encompass various algorithms, such as RC4 and ZUC for stream ciphers, and DES, 3DES, and AES for block ciphers. They are mainly used to address issues related to secure transmission, secure storage, and have a wide range of applications. However, these algorithms also have drawbacks, such as difficulties in key distribution and the inability to provide non-repudiation, which restrict their application in certain scenarios.

.

<p>The post Dahua Easy Installation Manual v1 first appeared on NVR IPCAMERA SECURITY.</p>

Disable audio recording on Dahua Recorder

Description

This article is to show how to disable audio function in Dahua IP camera that connected to Dahua NVR.

Video Instruction

Step by Step Instruction

1. Login to Dahua recorder from local system interface.

2. Under Settings, click on Camera.

3. Go to Encode.

4. Select the camera channel.

5. Click on More.

6. Click on the toggle to turn off Audio. Click OK.

7. Click Save.

Dahua NVR Troubleshoot All Series

Read Also : Tuya Camera User Guide Ultimate Manual

Disable audio on Dahua IPC that connected to Dahua NVR

This article is to show how to disable audio function in Dahua IP camera that connected to Dahua NVR.

Video Instruction

Step by Step Instruction

Step by Step Instructions

1. Login to Dahua NVR Web GUI using Internet Explorer.

2. Click on Settings > Camera.

3. Click on Camera list (Some recorder will label it as Registration)

4. Find the camera channel you want audio to be disable, click on E Internet Explorer icon.

5. It will take you to the login page of Dahua IP Camera. Login with Camera credential.

6. Go to Settings > Camera > Audio. By default the Audio settings is enabled.

7. Click on the checkmark to uncheck on both main and substream.

8. Click Save.

.

No Audio from Live Feed

There are following possibilities:

1. Make sure your audio on the computer or television is enabled and working by playing music or watching a video with audio online. You should see this audio meter change when playing music or video on the computer/television.

2. Once you have confirmed your audio is working on your speaker, and if you still can’t hear from your Live Feed, check your connections. If you are using an external microphone that plugs into the camera, please make sure you are supplying power to since the camera does not. See picture below:

.

3. If your connections and power are in order but you still cannot get audio from your live feed, log into your IP Camera or NVR and change the following settings.

4. If you are accessing your audio feed from a computer also make sure you have the speaker symbol enabled to enable audio from the Live Feed.

.

There is Audio from Live Feed, No Audio During Playback

There are following possibilities:

1. Make Sure your camera with a microphone is working via live stream, please follow the NoAudio guide for details.

2. After ensuring you are receiving an audio feed, log onto your NVR and make sure your encoding setup is correct (Setup>Image>Encode>) and make sure your are on the right channel where the camera has a working microphone. Now make sure audio is enabled for either or both the Main Stream and Sub Stream (whichever you are recording on)

3. Also make sure your camera is scheduled to record during specified operation.

4. Also make sure your camera is set to record

5. Now playback a recording of a camera that had picked up audio, you can also simulate this by making noise by the microphone and playing that segment back. Also make sure that the Volume button is not on mute and is turned all the way up during playback.

There is no HDMI output.

Video Loss 1 Camera

There are following possibilities:

Video Loss on Multiple Cameras

There are following possibilities:

Camera Feed is Blurry or Distorted

There are following possibilities:

Video is distorted when searching local records.

There are following possibilities:

Explanation:

1. If Video quality setup is too low then reconfigure video quality setup.

2. If Program read error, bit data is too small. There is mosaic in the full screen. Please restart the DVR to solve this problem.

3. If HDD data ribbon error then replace ribbon.

4. If HDD malfunction then replace HDD.

5. If DVR hardware malfunctions then replace hardware.

Remote control does not work.

There are following possibilities:

Explanation:

1. If Remote control address is not correct then find the correct address.

2. If Distance is too far or control angle is too small then shorten the distance or fix control angle.

3. If Remote control battery power is low then replace battery power.

4. If Remote control is damaged or DVR front panel is damaged then replace remote control or DVR front panel.

System does not boot

There are following possibilities:

NVR Randomly Rebooting or Shutting Down

Issue: NVR Randomly Rebooting or Shutting Down

There are following possibilities: Explanation:

1. If Input voltage is not stable or it is too low, then change the power supply and cable.

2. If HDD malfunction or something wrong with the ribbon, then replace the HDD or the ribbon.

3. Button power is not enough, then add more button power.

4. If Front video signal is not stable then check and adjust front video signal.

5. If Working environment is too harsh, too much dust then clean it.

6. If Hardware malfunction then replace hardware.

How to set the date and time

Time display is not correct.

There are following possibilities: Explanation:

Step by Step Instructions

1. Make sure the “Time Zone” is set correctly.

GMT stands for Greenwich Mean Time.

2. Setup DST, if applicable.

3. “Sync PC” if all else fails.

4. Click, “OK” to save your changes.

Burn error /USB back error.

Explanation:

1. If Burner and NVR are in the same data cable, then separate them.

2. If System uses too much CPU resources. Then please stop record first and then begin backup.

3. If Data amount exceeds backup device capacity which may result in burner error. Then please delete data.

4. If Backup device is not compatible, please change backup device.

5. If Backup device is damaged, please change backup device.

<p>The post Dahua NVR Troubleshoot All Series first appeared on NVR IPCAMERA SECURITY.</p>

with a wealth of intelligent products, we strive to identify and satisfy diverse demands by delivering intelligence at your fingertips; through innovative AIoT applications, we are dedicated to empowering every individual to enjoy a better future by building an intelligent world that is more convenient, efficient and secure.

Hikvision ‘How To’ Tutorials

Here you can find all of the Hikvision-related ‘How-To’ Tutorials that the team at use-IP have created

How Do I Configure the Camera’s Onscreen Display Text?

All Hikvision users will have seen that when you first log in to a camera the live view will have overlayed text stating the date & time and the default name of the camera “IPcamera 01”, depending on your requirements you may want to change some or all of this overlay text and below is the instruction for how to do that.

Method 1 – In a Web Browser

Log in to the camera and go to Configuration > Image > OSD Settings
.

Below we will take you through each of the above settings and what they do:

Character Set – This lets you select the characters/language the OSD settings use, by default all UK stock will come with this set as GBK for English characters but if you are a European customer and you want to enter special characters from your particular language (e.g. é, ü, ç, etc…) you can switch it to EUC-KR to access those characters (do this will require the camera to reboot).

Display Name / Date / Week – These tick boxes let you show/hide the camera name (Display Name), the current date (Display Date), and the day of the week (Display Week)

Camera Name – This box lets you set the displayed name of the camera, it will also change the name of the camera shown in the System menu and if added to an NVR it will change the name shown in the live view camera list and the Camera Management list.

Time Format – This dropdown lets you select how the time appears in your live view, either 24-hour format (00:00 – 23:00) or 12-hour format (00:00 – 12:00)

Date Format – This dropdown lets you select how the day, month, and year are displayed. Your options are DD/MM/YYYY (UK format), MM/DD/YYYY (US format), and YYYY/MM/DD (Chinese/International Standard format). You also have the option of separating the day, month, and year with either a “–” or a “/“.

Text OverLay – On most cameras, you should have the option to add up to 4 additional text overlays to the live view. You can use all of them or none of them depending on your requirements.

Display Mode – This dropdown lets you choose how the text behaves on screen, by default it will usually be set to Not Transparent & Not Flashing which means the text will obscure objects/people behind it and it will be onscreen all the time. You have the option to change it to one of the following – Transparent & Flashing / Transparent & Not Flashing / Not Transparent & Flashing – When set to transparent the text will become semi-transparent so that you can see objects/people behind the text and if set to flashing the text will flash on & off screen every few seconds (there are no controls for the flashing duration).

OSD Size – Technically this setting should adjust the size of the OSD text but we’ve found that when changing it there was little change to the text and so we would just stick to the default Auto option because this will allow the text size to adapt based on where you are viewing the live image (e.g. whether a small phone screen or a large TV).

Font Color – This dropdown lets you select the colour used by the OSD text, by default the camera will use Black&White Self-adaptive which means the text colour will automatically switch between black & white based on what is behind the text (e.g. if a person walks through the text) and for high-security sites, this can be an important feature for using the footage in court because the adaptive text shows that the image/text has not been manipulated in post. If the scenario requires it you can select Custom which will allow you to pick the text colour from a standard colour table.

Alignment – Again like OSD size this setting doesn’t appear to have a huge impact so we would just leave it as the default Custom and you can adjust the positioning/alignment of the OSD text by dragging the red boxes around the live view window above (these red boxes are only for adjusting the text position and will not appear on the actual live view image).

Hikvision How To Tutorials Chapter 1

Read More : Hikvision Devices password reset all methods guide

.

Method 2 – Via the NVRs GUI

.

You can access similar OSD settings from the NVR by going to Camera > Display and selecting the camera you want to configure.

.

Although, as you can see from the above screenshot you won’t get all the settings that can be found by logging into the cameras directly.

How do I set up ‘Rotate Mode’ on my Hikvision IP camera for the best picture in narrow scenes?

Corridor mode is a really useful feature available on many different CCTV cameras that can be utilised to effectively monitor a space that is more vertical, rather than horizontal, in shape. These types or areas include hallways, pathways, staircases, shopping aisles, tunnels and roads. When installing and viewing a CCTV camera, you want the image frame to include as much of the area of interest, while cutting out as much of the redundant areas, like the walls and ceiling, as possible.

Corridor mode allows you to rotate the camera’s lens and the video image 90 degrees so that it’s in a portrait, rather than a landscape format. As a result, you can use the camera to really focus on those areas of interest of within in your frame changing the image’s aspect ratio from 16:9 to 9:16 to suit narrow monitoring settings. The image below is taken from a camera making use of this function and illustrates the differences between the corridor and standard settings:
.

This guide will show you how to utilise corridor mode on Hikvision’s three most popular camera types: domes, turrets, and bullets. I will cover how to activate this useful setting in iVMS-4200, a browser, and locally through your NVR’s GUI so that, irrespective of your setup, this guide should be of help.

Part 1: How do I activate the corridor mode function in my camera’s settings?

We suggest getting your camera set up on your network and activating corridor mode in its settings before you try to rotate and position the lens. This way, you can use the live video stream, in the correct aspect ratio, to point the lens in your optimum direction. Positioning the lens often involved a bit of trial and error to get the best result specific to your space.

.

Note – For the G2 AcuSense models, you will need to connect to the camera directly in a web browser and change the “VCA Resource” to Monitoring Mode by navigating to:​

​

Configuration → System→ System Settings → VCA Resource​

​

​

.

​

Please note that this will disable most of the smart event options, leaving only Scene Change Detection available to use. ​

Locally (via a monitor connected to an NVR):

If your camera is connected to an NVR, then you can easily configure corridor mode in the setting through the NVR’s GUI menu. Just Navigate to:

Menu > Camera > Image

Pick your camera from the top drop-down box beside Camera and then select “Clockwise 270 degrees” in the Enable Image Rotation box

Then, just click Apply

Through iVMS-4200:

If you’re not using an NVR, or don’t have easy access to your NVR’s GUI, then an option is to use iVMS-4200 to set up corridor mode by accessing the camera directly.

To do this, first, you’ll need to navigate to:

Menu > Device Management

.

Find your camera in the device list. If accessing a camera connected to an NVR, you’ll need to open your NVR within the Group section of the Device Management screen and then the particular camera within the NVR’s device list.

Click Configure (the small cog) on your camera.

If your camera isn’t connected to an NVR, then open Basic Settings, if it is then open Advanced Function.

.

In the popup window, open the Image tab in the sidebar. You should then see either a tick-box or drop-down that allows you to turn on Rotate, tick or select ON in the applicable box or drop-down and then Save. The camera view should now have been rotated.
.

.

In a web browser:

The other method commonly used to access cameras and NVRs is through a web browser. You will only be able to configure the image rotation settings for a remote camera. The image for cameras connected directly to an NVR cannot be rotated in this menu due to the restricted access to the camera’s settings.

To access your camera in a browser, simply input its IP address into the browser’s address bar and hit enter. You’ll be taken to a login screen, here you’ll need to fill out the username and password combination you created for the camera when you first set it up. If correct, you should be taken to a page displaying the camera’s live video stream.

The process of rotating the camera’s image is relatively similar to that in iVMS-4200, just go to:

Configuration > Image > Video Adjustment > Rotate > On

The setting should be automatically saved, you’ll see a popup in the bottom-right corner of your window confirming this. That’s it!

.

.

.

Part 2: How do I position and rotate my camera’s lens correctly?

Rotating the camera’s image through its settings will rotate the image 270 degrees. To rotate the final video stream to the desired 180 degrees, you will manually need to turn the camera’s lens 90 degrees in the opposite direction as compensation. The entire process allows the rotated image to properly fit a 9:16 portrait aspect ratio. You’ll need to follow the below steps in order to rotate the camera’s lens.

For Domes / Mini Domes:

Domes and mini domes are the fiddliest type of camera to move and rotate the lens on. You can do this with the camera either installed or taken down. You’ll need to take the outer casing off the dome first to allow you to move the lens inside.

Then, loosen the locking screw located to the right of the lens rotate to allow you to move the lens and bracket. Now twist the lens bracket (the bit that can turn surrounding the lens, see the picture below) 90 degrees anti-clockwise, so that the gap in it is in the 3 o’clock position. You should see the “90” marker in the middle of the gap once in this position.

Now twist the lens (see the picture below) 90 degrees anti-clockwise, holding the lens bracket in place while doing this helps, so the “90” marker is at 12 o’clock and the “0” marker is in the 3 o’clock position. It may take a bit of wiggling and feel unnatural but the lens will move to this position, you won’t break anything!

.

Finally, rotate the lens bracket 90 degrees clockwise so that the gap is at 6 o’clock, and then move the lens so that is fits into this gap, so it looks like the picture below. This next stage takes a bit of trial and error on your part to get your desired camera view.

You’ll need to fiddle around with the lens while looking at the camera’s live stream to ensure it is straight and something you’re happy with. Viewing your stream through iVMS-4200 or Hik-Connect is best as you can look at the image and remotely while fiddling with the lens position at the same time.

.

For Turrets:

Rotating the lens on a turret camera is a slightly more straightforward process. First, you’ll need to remove the trim ring (shown in the picture below) by twisting it anti-clockwise and lifting it off the base of the camera.

.

This should expose the locking screw, you’ll need to loosen this using a Phillips-head screwdriver enough for Turret’s ball to be rotated. You shouldn’t need to take the screw out entirely. All these parts are labeled in the picture below. The “UP” marker on the ball indicates the top of the camera.

You’ll now need to rotate the ball 90 degrees anti-clockwise so that this marker moved from the 12 o’clock to 9 o’clock position. Now, tighten the locking screw back up and replace the trim ring to its original position. The lens should now be appropriately rotated.

.

For Bullets and Mini Bullets:

The camera models that allow for the easiest rotation of their lenses are bullets and mini bullets.

It is important to note that the sun shield on these cameras cannot be moved to be above the lens when rotated, which presents a drawback so using them for corridor mode.

The sun shield will sit to the side of the rotating lens in this case so you’ll need to make sure that you shelter the camera somewhat (such as under the eaves of a roof) if setting a bullet or mini bullet for corridor mode.

Mini bullets have a locking nut (shown below) at the end of their base which will allow you to rotate the camera when loosened. Larger bullets will require you to loosen the locking screw, which is the screw furthest to the right of the base if looking at them (shown below).

Once you’ve loosened the locking screw/nut as appropriate, rotate the main body of the camera 90 degrees anti-clockwise, so that the sun shield is in the 9 o’clock position. This will rotate the lens. Once you’ve done this, tighten the screw or nut again to secure the camera in its newly rotated position.

.

.

Part 3: How do I change the layout of my camera streams to accommodate for corridor mode?

Once your camera is all set up in corridor mode, you’ll want to be able to adjust the way that you view the grouped cameras to avoid the camera’s live stream being reduced in size to fit the standardised landscape 16:9 frame. This is easily done by simply merging two of the landscape frames to make a portrait, 9:16 frame to which you can dedicate your camera.

This custom view layout can be set up in an NVRs local GUI and in iVMS-4200. Please see the guides below for an explanation on how to customise your stream layout to accommodate corridor mode.

In iVMS-4200:

Click on the small icon made up of several small boxes at the bottom of your Main View screen in the program, this should bring up the window division page. Click Add to create a Custom Window Division.

.

In the Add Custom Window Division popup, set the name and dimensions of your new stream layout as desired.

Now, click and drag your mouse over the two frames you want to merge to select them both. Once they’ve both been highlighted by a surrounding red box, click Joint to merge them. Now click Save.

.

Once back in the Main View, click on the Window Division icon in the bottom right-hand corner again and select your new custom layout from the list. Your new stream layout should load ready for you to assign the individual cameras to.
.

Locally through your NVR’s GUI:

Please Note – This option is only available on NVRs that are running Version 4 firmware. There is not currently an option to customise your stream layout on K-Series recorders. If you’re running Version 3 firmware then your only option is to configure your layout as per above in iVMS-4200.

It’s also useful to be able to customise the stream layout as viewed directly from your NVR’s GUI as this is many people’s preferred method for observing and configuring their camera feeds.

To do this, firstly, you’ll need to navigate to:

Configuration > Live View > View > Set Custom Layout (small cog in bottom-left hand corner)
.

In the Custom Layout Configuration popup, set the name and dimensions of your new stream layout as desired. Now, click and drag your mouse over the two frames you’re going to merge and click the Joint button in the top toolbar, followed by Save.
.

Once back in the Live View, click on the Split button in the bottom-right hand corner of your screen. Then, select your new custom layout from the Custom Layout list that appears to load your new stream layout. You can then add the camera streams to each frame as appropriate.
.

You should now be up and running with corridor mode set up properly on your camera! Feel free to start a new thread or comment below with any other questions or suggestions. Thanks for reading!

How Do You Setup Event Pre & Post Recording for a Hikvision Camera?

To Adjust the smart event pre-record and post-record you need to follow these steps:

1) Log in to the NVR/Camera

2) Go to Configuration > Storage > Schedule Setting > Record Schedule

3) Click the ‘Advanced’ button at the top right of the record schedule
.

4) Select the duration you want from the pre/post record dropdowns and click OK
.

​

One thing to be aware of with event pre/post-recording is what Hikvision call a Buffer Zone. The buffer zone is simply a bracket of footage around the current moment in time that is continually recording/erasing, this buffer zone allows you to record only by event but still have access to footage before and after the trigger event without having continuous recording enabled.

The issue is that the buffer zone is limited to around 2-4MB of storage and so the higher your resolution and stream settings the larger the files sizes are and thus the maximum duration of the buffer you can use is limited.

So basically an 8MP camera will not be able to have as long pre/post recording durations as a lower-spec 4MP or 2MP model. (unless you reduce the resolution/stream settings of the 8MP camera)

We recommend that to get the longest duration possible from your pre/post recording you should set them to the not limited option to use the full 2-4MB buffer capacity.

(One other thing to be aware of, there is no advantage or disadvantage for pre/post recording when using an NVR. Although the NVR is managing the event recording, each channel on the NVR is still set to the same 2-4MB buffer, the same as the individual cameras. So you would not get more pre/post recording capacity with 1x 8MP than you would with 8 x 8MP cameras on an NVR.)

How do I stop my Hikvision NVR from beeping?

If a Hikvision NVR notices what it deems to be a critical error, or “exception”, it will make a constant beeping sound to draw your attention to this.

These exceptions can occur when:
.

• A hard drive has not been installed or properly formatted

• There is an error with the hard drive, it has been damaged, or the cameras are just not recording properly

• A hard drive has been filled and not set to overwrite

• There is an IP conflict, preventing the NVR from operating properly

• The NVR detects an illegal login

• The NVR loses its network connection

Of course, ignoring these exceptions are not recommended. However, you can disable the beeping while you address whatever the issue is by following the steps below.
.

.

​

Step 1:​

Connect to your NVR in a web browser by using its IP address and logging in.​

​

Step 2:​

Check what the exception that is causing the beeping is in the NVR’s logs. To find these, go to:​

​

Configuration → System → Maintenance → Log​

​

Set the log search so that the “Major Type” is “Exception”, with the start and end time covering a period when the beeping has occurred.​

​

For example, you can see that it is an IP address conflict causing it in this case.​

​

Note – Camera disconnections will not cause the NVR to beep. ​

​

​

.

Step 3:​

Go to:​

​

Configuration → Event → Basic Event → Exception​

​

Find the “exception type” identified in step 2 in the dropdown on this page.​

​

.

Step 4:​

Select the exception shown in your logs from the dropdown.​

​

You will see that “Buzzer” is ticked as a “Normal Linkage” action, which is what is causing the NVR to beep.​

​

.

Step 5:​

Untick this, click “Save”, and the beeping should stop.​

​

My Hikvision NVR has both HDMI & VGA connections, can I connect two monitors to my NVR?

This question gets asked a lot and we have always assumed that as the larger Pro NVRs (9600 Series) have 2 x VGA & 2 x HDMI that they were the only models that would support any kind of multi-screen setup.

Today we did some tests with a selection of demo NVRs we have in our office to see if it was possible to connect two monitors to an NVR that only had 1 x VGA & 1 x HDMI, below are our findings from testing K-series & I-series NVRs

K-series (DS-7604NI-K1-4P(B) / DS-7608NI-K2-8P / DS-7616NI-K2-16P / DS-7716NI-K4-16P / DS-7732NI-K4-16P)

When we connected a monitor to both the VGA & HDMI of a 7604 4-channel NVR we were able to see the usual K-series GUI on both screens at the same time, but with the older K-series GUI when viewing on two monitors your actions will be synchronised (e.g. when you move the mouse on one screen the mouse will do the same movement on the 2nd screen, and this is the same for any action whether it’s opening menus and selecting individual live streams).

So the main disadvantage of this is that you can’t have different live views streaming on each monitor, both monitors will show exactly the same thing and the only difference will be that one will be a VGA quality. The advantage of these synchronised displays is if you have a setup with say a large wall-mounted monitor and a smaller desktop monitor,

you can have the HDMI output to the big screen while you operate from a smaller VGA screen, this kind of setup would be useful for any situation where you need to demonstrate a feature of the NVR or play back footage in real-time to a large group of people.

I-series (DS-7608NI-I2-8P / DS-7616NI-I2-16P / DS-7716NI-I4-16P /DS-7632NI-I4-16P / DS-7732NI-I4-16P)

We have a 7716-I NVR as part of our demo system in the office and when we connected two monitors to the VGA & HDMI connections on the back we got the live streams displayed on both monitors just like we did with the K-series NVR. The difference with the I-series NVRs is that they use the latest 4.0 GUI, and on the live view page of this new interface you will find an icon in the bottom right

of the screen labelled ‘AUX Monitor’ (see image below), clicking this icon allows for you to switch control between the HDMI & VGA screens and allows you to move through the NVR menus on one screen whilst keeping the cameras streaming on the 2nd screen.
.

​

Now that you have the ability to switch between and control multiple screens you would obviously want to be able to set each screen up with their own camera stream layouts, to do this simply go to the System page (cog icon at the top of the 4.0 GUI) and then click the Live View tab and select the view page from the dropdown options. On this page you can switch between the HDMI & VGA screen and set the camera stream layout for each monitor (see image below).

There are limitations to how you can set the layouts, you can set the same camera to appear on both screens in the same place or in different positions and you can also spread all 16/32 cameras out across

the 2 screens, the main thing you can’t do is have a camera appear in different positions when using different live view layouts on the same screen (e.g. if you put camera 1 in the top left position for the 2*2 layout it will also appear in this top left position when you switch to the 3*3 layout).
.

9600 Series, Deep in mind, and Other NVR models

We don’t tend to get hands-on with these larger, top of the range NVRs but as you will see from the product pages and datasheets for these models a lot of them have 2 x VGA & 2 x HDMI connections. We assume that the 2 x connections on these models takes the multi-screen setup one step further by allowing you to seamlessly

move your mouse between screens (like you can with a 2 screen setup on a PC), thus allowing you to adjust each screens layout with ease and see all your camera streams in full quality via HDMI connection on both screens. (be aware that you will only see the full resolution stream of each camera when you select to view main-stream)

If anyone out there on the forum has had experience using two monitors with a 9600 Series NVR (or any other top of the range NVR with dual VGA/HDMI ports) then please share any information you have in this thread.

How do I set my Hikvision ColorVu camera’s built-in light to turn on during event periods?

We’re often asked if a ColorVu camera’s built-in supplementary white light can be programmed to turn on during VCA event trigger periods, such as during instances of motion detection, intrusion detection, or line crossing detection.

After testing, we can confirm that this is now possible on all 2nd Generation ColorVu cameras (any with a ‘G2’ in the part number) and works reliably.

In effect, it means the light on the camera can be used like a PIR floodlight, but with more control over a number of variables. Notably, trigger object type (human, vehicle, or both), the motion detection area, and direction of trigger object movement.

Please see the below steps for instructions on doing this.
.

.

.

Step 1:​

Connect to your camera directly in a web browser, even if it is recording to an NVR.​

​

If your camera is connected to your local network, just use its local IP address to do this.​

​

If it is directly connected to your NVR’s PoE ports, then you will need to use the virtual host feature to connect to the camera via your NVR’s Camera Management page.​

.

Step 2:​

If you have a ColorVu camera from the G3 platform, then make sure you have installed the firmware, version 5.5.800 (build 210628), or later.​

​

If you have one of the G5 models (indicated by a ‘C’ at the end of the part number), install version 5.7.2 (build 211228).​

​

You can also check your camera’s platform when connected to it in a web browser by going to:​

​

Configuration → System→ System Settings → Basic Information​

​

The platform will then be indicated by either a “G3” or “G5” in the “Firmware Version Property” box:​

​

​

Note – Please see this guide for instructions on how to check and update the firmware on your camera.​

.

Step 3:​

Once you’ve logged in, navigate to:​

​

Configuration → Event → Basic Event (for motion detection) / Smart Event (all smart event options support this) → Select your preferred event type​

.

Step 4:​

Enable and set your event up in the Area Settings and Arming Schedule pages, this guide explains how to set up motion detection, line crossing, and intrusion detection.​

.

Step 5:​

Navigate to the “Linkage Method” page, tick the “White Light” box, and set how long that you want it to remain on for on event triggers (in seconds) in the “Duration” box.​

​

Click “Save” once this is done so the settings are kept.​

​

How do I use a Hikvision NVR’s “Virtual Host” feature?

One of the most successful selling points of a Hikvision NVR to many small-setup customers is the “Plug and Play” functionality that simplifies the setup process of their surveillance system.

However, plugging a camera directly into a port on the NVR, unfortunately, does not allow you to access the camera via its own internal LAN IP using a browser due to it being on the NVRs internal network, and this can significantly reduce the number of configuration options you have access to.

The NVR does allow you to configure many options for each connected camera, but some essential features are only accessible via connecting to the camera itself (such as audio codec options). This was of course a big problem previously.

With the advent of newer firmware and models of NVR, Hikvision has introduced a feature called Virtual Host. Activating this feature turns your NVR into a “host” for the cameras allowing you to connect to them via a browser. Essentially, the NVR forwards all traffic received from your browser to the appropriate camera you’re trying to connect to, eliminating the biggest problem of plug and play functionality.
.

.

Step 1:​

First of all, access your NVR via a web browser. If you do not know the LAN IP of your NVR, download Hikvision’s tool SADP tool, which scans your network for any Hikvision devices that are connected and allow you to see and change their network settings, including the IP address.​

​

Download SADP for Windows ​

Download SADP for MacOS​

.

Step 2:​

Once you’ve logged in, navigate to: ​

​

Configuration → System → Camera Management​

.

​

.

This screen displays all the connected cameras on your NVR. Notice that the final column labelled “Connect” is currently empty. We’ll be coming back here in a moment.​

.

Step 3: ​

Now, navigate to:​

​

Network → Advanced Settings → Other ​

​

Turn on the Enable Virtual Host option.​

​

Note – Your NVR will reboot when you click “Save”.​

.

.

​

Step 4:​

Now, navigate back to the Camera Management window from earlier. You’ll notice that the previously empty connect tab now features links for each camera currently connected to your NVR.​

.

​

Step 5:​

Click on any of these links to access the respective camera via your web browser:​

That’s it, you’re done!

This should be useful when you want to access options on your camera that your NVR doesn’t feature. If you have any further questions feel free to ask, we’re happy to help.

Why am I not able to tilt my Hikvision PTZ camera upwards?

Hikvision PTZ cameras are not usually set by default to have their full range of movement enabled. This often means that cameras that are advertised as being able to tilt upwards are not able to do so straight out of the box, as this needs to be enabled in the camera’s settings.

You can check the movement range available on your camera in the PTZ section of its datasheet. Below is an example of this range shown for the DS-2DE5425IW-AE (S5):
.

​

0˚ tilt refers to the camera being in its home position, where it running parallel to the ground beneath and looking straight out at the scene.​

Any negative figure (e.g. -15˚) here refers to the angle that it can tilt to upwards of the 0˚ position.​

Any positive figure (e.g. 90˚) refers to how the angle of tilt available below this 0˚ position.​

​

Cameras with “auto flip” will rotate 180˚ and then flip their image when it reaches its full 90˚ downwards tilt, which will give the illusion of you having a full 180˚ (or more) range when you try to continue to tilt beyond this 90˚ position.​

To change the movement range currently set on the PTZ, you will need to connect to the camera directly in a web browser.
.

NB – If your camera is directly connected to an NVR’s network ports, then you will need to use the Virtual Host feature to access the camera’s backend. If it is connected to your local network, then you can just browse for its IP address to do this. ​

Then, go to:
.

Configuration > PTZ > Basic Settings > Max. Tilt Angle​

​

​

You should have some different options in this dropdown, depending on the maximum tilt range of your camera. If you want to enable the complete range of movement, then select the option with the largest range between the two figures (in this case, “-15 – 90˚”).​

Once you have chosen an option that you’re happy with, make sure to click “save” at the bottom of the page so that these changes are updated on the camera.

How do you Shutdown a Hikvision NVR?

This is a common question by Hikvision users so we thought we would create a short forum post to give a clear answer on the possible ways to shutdown an NVR.

Direct Monitor Access
If you are accessing your NVR from an HDMI/VGA monitor then it is possible to shutdown the NVR from within the menus, depending on the NVR model the menus and shutdown process is slightly different as you will see from the below explanations:

I-series (76xxNI-I2 / 77xxNI-I4 / 96xxNI-I8 / 96xxNI-I16) & K-series (7604NI-K1/4P(B) / 76xxNI-K2 / 77xxNI-K4) NVRs – In the top right corner of the live view you will see a power icon which if you hover over will bring up text that says either ‘Power’ or ‘Power Off’, click the icon and a pop-up menu will appear with 3 options, one of which will be shutdown.

Click shutdown and a box will appear saying ‘shutting down…’ and then after 20-30 seconds, new text will appear asking you to switch the NVR off at the back to complete the shutdown.

(Above is for I-series and K-series NVRs that are running 4.0 GUI and EUI GUI respectively, if your NVRs are running older firmware and not using the latest user interface you will need to follow the below instructions)

7604NI-K1, E-series (76xxNI-E1 / 76xxNI-E2 / 77xxNI-E4), SE-series, and other older generation NVRs – Right-click the live view page and select the main menu from the dropdown, one of the menu options should be clearly labelled ‘Shutdown’ which when clicked should bring up the same 3 options as mentioned above.

Click ‘Shutdown’ and a window should appear with the text ‘shutting down…’ and roughly 20-30 seconds later new text will appear asking you to switch the NVR off at the back to complete the shutdown.

Browser Access
if you are accessing the NVR primarily from a browser then your only option for shutting the NVR down is to simply flick the switch on the back of the NVR because the browser menus do not include a button to shut the NVR down like you can with the direct monitor.

How do I know if the lens on my Hikvison mini dome is orientated correctly?

It’s easy to install your Hikvision mini dome only to turn it on and find that the image is upside down. If you’re not familiar with Hikvision cameras, adjusting the lens and settings can be confusing. This post will explain the two different ways that you can rotate your camera’s image by:
.

1.Manually rotating the lens itself.

2.Rotating the cameras image 180° in the image settings.

Part 1: How do I orientate my camera’s lens manually?
.

1.Remove the mini dome’s cover by loosening the screws surrounding the glass dome, shown in the image below:

.

2.You should now be seeing something like the image below. Loosen the locking screw to the right of the lens, and then the lens bracket which locks the orientation of the lens in place. The lens is effectively attached to the camera body via a ball and socket joint, so this can be orientated however you like.

Part 2 of this guide explains rotating the lens in more detail, as well as how to rotate the lens on the turret and bullet styles of camera – How-to: How do I set up Corridor Mode on my Hikvision Turret, Bullet or Mini Dome IP CCTV camera?

NB – This image shows a camera with the lens rotated 180°, you’ll actually need this 90° marker to be in the 3 o’clock position, and the 180° marker pointing towards the bottom of the unit.

.

3.The lens should be positioned like the one shown in the below image. The small line marker located directly parallel to the 180° marker signifies the top of the lens. So, this needs to be pointing up, towards the top of your scene. This will orientate the camera’s view correctly. You should also make sure that the lens bracket is repositioned correctly so that the thicker part surrounds the top half of the lens.

.

4.Now, tighten the locking screws and fasten the dome cover back in place, making sure the cover screws are tight to prevent water ingress into the camera. It’s always worth checking your camera stream before doing this to make sure that the camera view is orientated as you like.

For a guide on installing you Hikvision IP camera correctly to ensure it is properly waterproofed, please see this guide – Please Read: IMPORTANT – Installing Hikvision IP Cameras Correctly

Part 2: How do I orientate my Hikvision camera’s view through its settings?
.

1.Log into your camera’s web browser interface (not your NVR’s), by entering its IP address into the browser’s address bar. This will only work for cameras that are on the same LAN as your PC. If the camera is directly connected your NVR’s PoE ports, then you will need to use the NVR’s ‘VIrtual Host’ feature to access the camera’s own browser view, which gives you access to a wider range of settings.

NB – It is recommended that you use Internet Explorer if possible. If you are a macOS user, the best web browsers for this seem to be Google Chrome or Apple’s Safari. You might need to install Hikvison’s macOS Web Plugin as well.

2.When you have access to the cameras in a web browser, go to:

Configuration > Image > DIsplay Settings > Video Adjustment

The different options are will adjust your image as described below:

Left/Right: The image will be flipped horizontally, so it appears as a typical mirrored image.
Up/Down: The image will be flipped vertically, which will still show a mirrored image of the default view as you are not actually ‘rotating’ the image 180°
Center: This will be the option that you need to select to rotate the image 180°, which will show the same view as physically rotating the lens would.

If you only need to rotate the image 90°, then setting the Rotate option to ON will do this, as shown below.

To rotate your view 270°, set the Mirror dropdown to Center, and then set Rotate to ON.
.

Thanks for reading – hopefully, this will prove helpful to some of you in the future! As always, please feel free to post any questions or feedback that you have below or by creating a new thread.

Hikvision Password Reset Options – 4 Ways the User can reset their Passwords

The new video from Hikvision (linked below) takes you through the 4 password reset options that the user can do themselves, these are:

1. Reset Password by reserved email
2. Reset Password via Hik-Connect App
3. Reset Password via Security Questions
4. Reset Password via GUID File

IMPORTANT: Not all of the above options will be available on all Hikvision products, also be aware that all the above options do require some level of pre-configuration to use them so if you have done none of the setups explained in the video you will have to follow the traditional reset file method as described here (remember though that we at use-IP will only reset passwords of our own customers)

How to Set up the Hikvision 2nd Generation Modular Intercom

We get asked a lot of questions by people looking to buy or who have already bought Hikvision’s 2nd Gen modular Intercom solution and for a long time, we have had to take the majority of those questions to Hikvision Support as we just don’t have enough hands-on experience with the intercom solution to answer them confidently.

Now we have finally found time to get a demo intercom system set up, test some of the features, and give you a guide of how to get a basic intercom solution up and running.

The below guide will initially** be split into 3 key sections with multiple sub-sections:

Single Module Setup (Video Intercom Module)
.

• Setting up the Video Intercom Module

• Setting up the Indoor Station

Three Module Setup (Video, Indicator, Keypad)
.

• Sub Modules & Dip Switches

• Setting Room Numbers & Unlock Codes

Six Module Setup (above + Display, RFID, nametag)
.

• Nametag & Display Modules

• Card Reader Module

The reason we have decided to cover it this way is that the modular nature of the solution means there are too many variations to cover specifically, so instead we will cover the details of the 3 most common setups and once you know the basics of all 3 any combination of modules should be achievable.

(**IMPORTANT – This will be a continual work-in-progress thread and we will add new posts with explanations of new features & settings as we test the intercom further and learn things from customers & Hikvision Support, this initial post will basically be a contents page for the entire thread)

Will the smart tracking feature on a Hikvision PTZ camera allow it to zoom in to its maximum zoom ratio automatically?

We’re frequently asked if Hikvision PTZ cameras will automatically zoom in to their maximum ratio when they are automatically tracking a target. After talking to Hikvision, we found out that you’ll need to do the following to enable the camera to do this:

On the camera’s menu (via a web browser) navigate to:

Configuration > PTZ > Smart Tracking

Here, set the Zoom Ratio to its maximum value, which will then allow the camera to automatically zoom to this maximum ratio.

Do It Youself – How To Silence a HikVision DS-7608NXI-I2/4S AcuSense NVR

Hi Guys,

I’m new to business here, but have made a video tutorial to decrease fan noise on my AcuSense 7608-NXI-i2-4S device. Maybe this helps others as internal construction of many NVRs from HikVision seems to be almost the same.

I also have some questions towards the community.
1. What is my latest firmware available for my NVR?
It is an AcuSense 7608NXI-i2-4s, but as I see it is not a full i-series device.
i-series are up to 4.22, but mine seems to be different. Can I use firmware here or not: Firmware – Latest HikVision Firmware for I-Series NVRs – V4.22.005

2. Scene change detection+alarm seems to be problematic. My cameras are AcuSense 2086G2 Bullet, but they do only detect scene change when going completely dark scene to normal recording scene. If I let them record a normal scene situation and then simulate a camera removal from wall situation – camera does not trigger a scene change event.

How to update the Hik-Connect App on your Android phone using Hikvision’s App Store

The method for updating the Hik-Connect App on Android devices has recently changed to mean that users can no longer update via Google’s Play Store. To use Version 4.1.0 of the app Android users now need to access Hikvision’s own App Store and update via the .apk file which is downloadable from there. The reasons for this change have been discussed in this post, as well as our thoughts on the situation.

This simple tutorial has been put together to walk you through this new method for updating in 5 easy steps, so that you can ensure you install the latest version of the Hik-Connect app is installed properly on your Android device.

Step 1:
Open Hik-Connect if you have it already installed, and press the Upgrade Now button in the popup. If you don’t have the app installed or do not get this popup upon opening the act, this link to the Hikvision App Store will take you to the update file.

You need to make sure you open this page on the Android device that you wish to install the updated software on, as this will be the device that the update file is saved to! In the App store, make sure Android is selected in the top-left hand corner and then select Download beneath Hik-Connect to get the .apk update file.
.

Step 2:
Press Download when the prompt to do so appears at the bottom of your screen. Don’t worry, this is a safe and secure link!
.

Step 3
Select Install when the prompt to do so appears at the bottom of the screen.
.

Step 4
The installation will begin, wait for the progress bar to complete… Go and put the kettle on!
.

Step 5
If you get the same screen as the one below, then you’re all done. You should now have the latest version (V4) of Hik-Connect installed on your device. You can either press Open to launch the app, or Done to return back to whatever you were previously doing. If your screen doesn’t say App installed with a tick above, then you’ll need to repeat steps 1-4 again!
.

How do I set up an alarm to work with an external device on my Hikvision NVR?

We often have customers ask us “how do I get my new NVR to work with an existing alarm system I already have installed” or “how do I connect something to the IN/OUT ports of my NVR?” Indeed, for such an important feature for the NVR’s to have, it is not the most straightforward to get set up with.

We thought it would therefore be useful to put together this guide to walk you through how to configure the alarm function, either through locally through your NVR and monitor, or through Hikvision’s iVMS-4200 software, in 10 easy minutes.

.

Contents:

Part 1: How to wire my alarm system into my NVR’s alarm input and output ports?

Part 2: How do I configure the alarm function settings of my NVR locally via a monitor?

Part 3: How do I configure the alarm function settings of my NVR remotely via iVMS-4200?​

Part 1: How to wire my alarm system into my NVR’s alarm input and output ports?

As daunting as it may seem when you look at the multiple different alarm ports in the back of your NVR, this part is simple enough once you know what you’re doing. If you’re struggling to find you alarm IN/OUT ports, they are the block of green connections which should be labeled as “ALARM IN/OUT” on the device.

The number of connections will vary here depending on the size of your NVR, the picture shown is of a smaller Hikvision DS-7608NI-K2-8P 8 Channel NVR. Larger NVRs will have more of each connection, but nonetheless, the process is the same.

Firstly, make sure you can locate the NVR’s “ALARM IN ” and “ALARM OUT ” ports, with their corresponding “Ground/G” ports. If you’re connecting a device to trigger your NVR cameras with an external event (e.g. a smoke alarm, PIR senor etc) then you’ll need to run the wires from the device into one of the input ports and its corresponding ground port.

If you’re connecting a device to be triggered by a smart event set up on your NVR (e.g. a siren or warning light), then connect the wires to the output port and corresponding ground port. All the ports are marked up in the picture below but should also be clearly labelled on your unit.
.

Part 2: How do I configure the alarm function settings of my NVR locally via a monitor?

Now that all the necessary connections are made, you’ll need to set up your NVR’s alarm function for it to alert the alarm system that you’re connecting to it.

Firstly, I’ll show you how to do this locally. You’ll need to boot up the NVR, once in the menu, navigate to:

Menu > Configuration > Network > General

Here, you’ll need to insert your network’s IPv4 address, IPv4 subnet mask, IPv4 default gateway and your preferred DNS server:

.

• If you’re unsure of your IPv4 address, subnet mask or default gateway, our tutorials on How To find your router and PC’s IP address using a Windows PC or How To find your router and Mac’s IP address using a Mac show you how to do so. Please note, you need to make sure the PC you use to find these is hard wired via a network/Ethernet cable do make sure this turns up the correct addresses for your network/router.

• Unless you know of a preferred DNS server that you’ve set up yourself, Google’s public DNS server address (8.8.8.8) should work fine. It’s worth entering an alternate backup DNS too beside Alternate DNS Server, Cloudflare’s public DNS address is a good option (1.1.1.1). Follow this link for a list of the best publicly available DNS servers.

Now, navigate to:

Network > Email

At this screen, you’ll need to fill in all the fields as appropriate to your Email account. If you’re unsure of these, then complete the fields as below:

Enable Server Authentication: Tick/check this box
User Name: Insert your email address here
Password: Insert the password you use to access this email account
SMTP Server: If you don’t know this, follow this link for “finding your SMTP server address”
SMTP Port: Insert either 25 or 587 here
Enable SSL: Leave this box unticked
Sender: Insert the first part of your email address (everything before @)
Sender’s Address: Insert your email address here
Select Receivers: Insert “Receiver 1/any name” here
Receiver: Insert your email address (same as Sender’s Address)
Enable Attached Picture: Tick/check this this box, it will mean that you’ll receive picture of anything that triggers your cameras’ alarms in an email.
Interval: Insert 5s (5 seconds)
.

When you’ve completed these fields, navigate to:

Menu > Camera

Ensure all your cameras are properly connected to the NVR and are visible on this screen. If you haven’t yet added any cameras to your NVR, this guide on adding Hikvision cameras to an NVR walks you through how to do so.
.

Now, navigate to:

Menu > Configuration > Alarm

This should take you to the Alarm Status menu. This menu lists the status all your alarm IN/OUT ports and any alarms that have been configured/assigned to these ports.

You’ll need to use this screen to check that you’ve set the correct Alarm Type for the alarm/device that you’re connecting. The options you have are N.O (Normally open) and N.C (Normally Closed). In brief, N.O alarm types use switches/sensors that normally remain open with no current flowing through them, so closing the switch allows for the flow of current and activates the alarm.

N.C alarm types, on the other hand, use switches/sensors the normally remain closed with current flowing through them, so opening the switch stops the flow of current and activates the alarm. There’s a lot to be said about N.O and N.C alarms but for now, you only need to know which category the alarm that you’re using falls under. If you want to take a journey down the N.O vs N.C rabbit-hole, I found this article on the differences between N.O vs N.C useful.
.

To assign an alarm to one of these IN/OUT ports, navigate to:

Alarm > Alarm Input > Settings (click on the small cog) > Trigger Channel

Choose the channel that you would like to trigger your alarm. In this case, we’ve selected channel 1.
.

Now, navigate to:

Settings > Arming Schedule

Select the hours that you would like to schedule your alarm to be turned on for. Typically, this would be 24/7, so set the schedule for Monday, Week 1 as 00:00-24:00. Now, copy this schedule to the rest of the week by clicking Copy and then checking the box for All in the popup window. If you only want your alarm scheduled for certain days, then select the specified days in this popup from the list of 1-7 (1 = Monday, 2 = Tuesday etc).Once you’ve done this, click Apply.
.

Finally, navigate to:

Settings > Linkage Action

Tick the boxes for Notify Surveillance Center and Send Email and then click Apply so that you email notifications whenever the alarm is triggered. If you have connected a separate device to be activated by the alarm in the NVR’s Alarm OUT port, then ticking the box for Trigger Alarm Output will activate this device when your alarm is triggered.
.

That’s it for the local setup section of this tutorial! Your NVR’s alarm function should now be set correctly.

Part 3: How do I configure the alarm function settings of my NVR remotely via iVMS-4200?

The first thing you’ll need to do is ensure you have the most up to date version IVMS-4200 installed and that you’re able to view the live feed of your camera(s) through the software.

If you haven’t already added your NVR to the program, navigate to:

Maintenance and Management > Device Management > Add
.

Add your NVR here by filling out the fields in the popup window, ensure the boxes beside Export To Group and Synchronise Time is checked and then click Add.
.

Now find the NVR on your device list and select:

Remote Configuration (the small cog listed beside your NVR) > [Basic Settings] > Event > Alarm
.

NB the configuration menu layout you will see henceforth will vary between two depending on the model of NVR that you have. I have included both variations for each step, so don’t worry if some of the below screenshots look unfamiliar.

Fill out the alarm parameters here, e.g. as follows:

Alarm Input: Select your NVR’s channel that you would like to trigger your alarm (e.g.: A<-1)
IP Address: Local
Alarm Name: Name your alarm as desired
Alarm Status: Normal/Remain Open or Normal/Remain Closed depending on the type of alarm, see the first half of this tutorial to understand the differences
Enable Alarm Input Handling/Enable Alarm Linkage Actions: Check this box
Arming Schedule: All-day Template
.

.

Open Arming Schedule, pick an arming template or a custom schedule of hours that you want your alarm active for.
.

Now, Click Settings beside Linkage Method. Check the boxes for Notify Surveillance Centre, Email linkage and Trigger Alarm Output (if you’re connecting an external alarm device to an output channel), then set the desired Triggered Camera.
.

.

Click Save, and then Save again in the alarm configuration window.

Switch back to Main View and select your NVR from the side panel.

Now, click the small alarm picture and speaker icons at the very bottom toolbar so that they’re both enabled and look like the second image below. This will enable the alarm’s function to send an image of its trigger, as well as the audio.
.

That’s it for the remote setup! It’s always worthwhile testing your alarms to check everything is now working as it should be.

If you have any questions or comments to make, please do so in a separate thread mentioning this tutorial and I’ll get back to you as soon as I can.

How to Unbind a Hikvision Device using SADP on a PC

Unbinding a Hikvision device is not something that is required all that often, in most cases you can do the unbind from within the app. There are though some rare cases when the user does not have access to the Hik-connect account that the device is bound to, for example, if you have purchased a used device that has not been properly disconnected from its previous owners Hik-connect account or if you added the device to an employee’s account and they leave without removing the device from the app correctly.

As long as the Hikvision device has been set up correctly on your local network, then the process of unbinding should be pretty simple:

Step 1 – Open SADP on a PC
Step 2 – Click Refresh and select the device you want to unbind by ticking the box next to the device on the far left of the list
Step 3 – Click Unbind
Step 4 – Enter the current username and password of the device (this is NOT the username & password of the Hik-connect user you are trying to unbind the device from)
Step 5 – Enter the Verification Code and click confirm

You should then see a quick pop-up with a green tick saying Unbind Successful, If the device does NOT unbind and you get an error message like “The device is Offline” or “connecting device failed” then the most likely problem is that your DNS settings for the device are not set correctly.

You can change the DNS settings by logging in to the device using a browser and go to Configuration > Network > Basic Settings > TCP/IP and you will see the 2 DNS boxes at the bottom. We recommend that if you are unsure of what DNS to use that you enter default/most commonly used DNS servers which are shown below:

Prefered DNS – 8.8.8.8
Alternative DNS – 8.8.4.4

Once you have saved these DNS settings the unbind process should work

How do I update HikVision Firmware in just nine simple steps?

Updated 20-2-19 – corrected the link to the portal as Hikvision changed their url (again). Otherwise all is good. We use this method every day. Now viewed over 38,000 times.

Here’s how to upgrade your HikVision camera or NVR to the latest firmware version in just nine simple steps:

Step 1: Download the latest HikVision firmware to your PC.

Step 2: Extract the digicap.dav file (which is the actual firmware file) from the zipped file you downloaded.

Step 3: Copy that digicap.dav file to your PC’s root folder e.g. C://

Step 4: Browse to your NVR, camera, etc – using Internet Explorer:

Step 5: Login and navigate to Config -> Maintenance (screenshot attached below)

Step 6: Scroll to the bottom of the screen you’ll see Upgrade Firmware.

Step 7: Click the Browse button at the right-hand side.

Step 8: Browse to and select the digicap.dav file in your C:// drive

Step 9: Click ‘Upgrade’.
.

I have seen reports that you cannot leap updates, but not encountered the problem myself for some time (applies to old firmware of older models). If you do not succeed in upgrading from your current version to the latest version in a single step, please try interim releases.

Additional helpful tips:
.

1.Use a PC

2.Use a wired connection – PC and camera/NVR wired to your network

3.Use Internet Explorer browser (not Edge)

4.Move the digicap.dav file to your C:// folder (root of your HDD)

5.If you select/download firmware for the wrong camera family or device you will see an error message which states – “The type of upgrade file mismatches”

If you need any help finding the latest Hikvision firmware for your device:

Tutorial videos from HikVision Technical Support:

HikVision Firmware Update using Internet Explorer on your PC

HikVision Firmware Update using a monitor connected to your NVR

NVR Firmware update using a USB memory stick

Upgrade devices using IVMS-4200

NB We cannot guarantee outcomes – if you are one of our customers you will of course have our full support. We have only ever supplied official UK version HikVision cameras & NVRs. If you sourced your HikVision products from another supplier you may want to check their recommendations.

How To Set Up Live View & Playback Audio on Hikvision Cameras

There is a small selection of Hikvision cameras that support some sort of audio – audio I/O, built-in mic, 2-way audio – but on multiple occasions, customers have come back to us saying they are getting no audio on live view or playback. So to avoid this problem in the future we are creating this post to take you through the steps that must be completed to get audio from a Hikvision camera.

Step 1 – Update Firmware

Keeping firmware up to date is always important so it is always where we start with any issue, now most firmware should support the audio but if you’ve had a model for several years and never updated it you are likely on an old firmware and so updating just removes any potential problem that might be caused by out of date firmware.

EU Firmware Portal
UK Firmware Portal

The most common audio cameras will be EasyIP 2.0+ (2xx3G0) and EasyIP 3.0 (2xx5FWD/2xx5G1) which all use the same G1 Firmware.

Step 2 – Video & Audio

Login to the camera, go to the Configuration page and open the Video/Audio menu where you will see all the video settings. The important one for audio is the Video Type which needs to be changed from Video Stream to Video & Audio as shown below:
.

​

Make sure you also switch the Video Type of any other streams you are using, the main one for most cameras will be the sub-stream which is used when viewing the camera from the Hik-connect app. Also, if your camera is connected to a Hikvision NVR make sure to check the camera is set to Video & Audio in the NVRs Video Settings.

Step 3 – Audio

The final Settings to check are the Audio settings which more often than not out of the box is set up correctly and should look like the below screenshot:
.

​

The only setting that might change depending on the model you have is the Audio Input option. If you have a camera with only a built-in mic or 2-way audio then the only option you will have is MicIn, but if the camera only has audio I/O connectors or has both options then you will have both MicIn and LineIn input options. Make sure if your camera has both options that you select the correct input for your setup, LineIn will be used if you have a more powerful audio device connected like an amplifier or a stereo microphone, while MicIn will be for smaller standard Mono microphones.

With all 3 of these steps completed, you should now have live audio from the camera on the browser, app, and direct monitor live view, but there is one final step to have your camera record audio.

Step 4 – Record Audio

Login to your camera/NVR and go to Configuration > Storage > Schedule Settings and select the camera with audio, once you have the schedule for that camera onscreen you will need to click the Advanced button which you will see in the top right of the schedule. A pop up will appear and you will see an option to Record Audio, tick this option and click OK to apply the setting, now all the recorded footage from that camera will have audio.
.

.

.

<p>The post Hikvision How To Tutorials Chapter 1 first appeared on NVR IPCAMERA SECURITY.</p>

How to Set ANPR Solution

.

I. What is ANPR

ANPR(Automatic Number Plate Recognition) is a technology that uses optical character recognition on images to read vehicle registration plates. For Milesight, the ANPR algorithm is embedded in cameras, which allows the cameras to recognize, capture and upload license plate images all alone and intelligently.

II. Why Milesight ANPR Solution

Quick Capture & Accurate Recognition

• Accurate License Plate Identification Under all kinds of conditions

• High-reliability License Plate Recognition with more than 95% high performance accuracy

  1. Up to 4 Detection Regions

  2. Reliable Confidence Level

  3. Vehicle Direction Recognition

  4. Detection Regions of PTZ

  5. DACH Region Recognition

Read Next : Spot AI IVR Installation Guide

Intelligent Analysis & Efficient Management

• White and Black List Management

• A Stand-alone ANPR Solution

• Fully Integrated with Milesight NVR/CMS

• 3rd Integration: CGI

Adaptable to Most Operation Requirements

• Max recognition speed 120 km/h

• Over 70 countries and regions

• Various options

    LPR 12X H.265⁺ AF Motorized Pro Bullet Network Camera

    LPR 12X H.265⁺ Mini PTZ Bullet Network Camera

    LPR 12X H.265⁺ ABF Pro Box Network Camera

    LPR 12X H.265⁺ Mini Bullet Network Camera

    LPR 12X H.265⁺ Vandal-proof Motorized Mini Bullet Network Camera

    LPR 12X H.265⁺ Motorized Pro Bullet Network Camera

Notes:

Installation Angle Considerations

To increase the accuracy of license plate recognition, be sure to install the LPR cameras properly to capture the license plates with the correct image size, lighting conditions and camera angle. The following highlights is the precautions of installation angle：

A: Installing the camera in front of the vehicle (Recommended):

The captured image should be filled with a full width of the vehicle.

B: Installing the camera slightly to the side:

To avoid capturing unnecessary contents in the image, the camera should be installed in a higher position(Vertical angle is less than 30°; Horizontal angle is no more than 30°; Tile angle is less than 5°) to capture the front part of the vehicle.

III. Countries/Regions that support ANPR

Currently, we have three kinds of LPR, including LPR1, LPR2 and LPR3. LPR1 is used in Asian region, LPR2 is for European region, and LPR3 is for Korea. It covers over 70 countries and regions.

LPR1:

LPR2:

CIS (former Soviet Union)

IV. How to set ANPR with Milesight Network Cameras

1. Settings

Step1: Go to “Advanced Settings” → “LPR” → “Settings” after log in the web. Check the checkbox “Enable License Plate Recognition”, and you can draw the screen to select the areas interested. There will be shown in the blue box as below.

[License]: A license will be automatically assigned to each device.

[License Status]: This column is used to display the status of the license, “Valid” or “Invalid”.

[Processing Resolution]: Default resolution selected is 1280*720. You can choose different resolution according to the network environment.

[Set LPR Detection Region]: You can set up to 4 ROI areas by drawing the screen. If you choose Normal Mode, it supports configuring the LPR detection regions for the current area. If you choose Advanced Mode(Only for PTZ series), it supports configuring different LPR detection regions for different PTZ presets(Only support Preset 1~4 so far).

Note:

• The optimal interval of Milesight LPR cameras to recognize license plates width is within 100-200 PX.

• For better performance, please choose the appropriate resolution in advance.

[LPR Night Mode]: Achieve the best effect of LPR night recognition by adjusting different parameter levels. You can also schedule the Start Time and End Time, and adjusting the level according to the environment.

Step2: Schedule Settings. You can draw the schedule by clicking [Edit] button. And then click [Save] or [Reset] after finishing the setting.

Step3: Detection Settings and LPR Message Post Settings.

[Detection Trigger]: If you choose “Always”, camera will always detect the license plate. If you choose “Alarm input”, camera will only detect the license plate when Alarm Input is being triggered.

[Confidence Level]: You can set the confidence level from 1 to 10. When the confidence level of the license plate is higher than the set confidence level, it will push the license plate image to the logs interface..

[Repeat Plate Checktime]: Set the time interval for repeatedly reading license plates to effectively avoid duplicate identification of parking vehicles.

[License Plate Serial Format]: Formulate identification rules and automatically filter wrong license plate information to achieve more intelligent and accurate license plate recognition.

[Feature Identification]: Check Region, Direction, ROI_ID or All to enable Features Identification, it will display the corresponding information on the logs interface.

Note: Region detection only supports DACH region.

[LPR Message Post Settings]: Check the checkbox to enable LPR Message Post. It will push information to some third-party devices or software that are compatible with ours. Information can be pushed by RTSP, TCP or HTTP.

More information about LPR Message Post, please refer to Milesight-Troubleshooting-Integration between LPR Camera and NVR(VMS).

Step4: Don’t forget to click [Save] after finishing all settings.

2. List Management

Add the license plates to this interface as Black or White type (Black/White List), and then you can set the alarm action for these license plates in the corresponding black list mode or white list mode interface. When these license plates are detected, the camera will respond to your settings accordingly.

[Add License Plate]: Select the license plate type as black or white, enter the license plate number, click the “Add” button, the license plate number will be added successfully.

[Batch Upload]: You can add a csv file of the license plates you want to add, click the “Browse” button to import the form to this interface, click the “Upload” button, the license plates will be added successfully.

Note:

• You can first download the template as a reference in this interface.

• It allows to add 1000 license plates to Black and White List.

[List Search]: Select Plate Type or directly enter the license plate number, click the “Search” button, the corresponding license plate will be displayed in the list as below.

[Export List]: Click the “Export List” button to export the license plates in the current list as a csv file locally.

[Delete List]: Click the “Delete List” button to delete all the license plate in the current list.

3. Black/ White/ Visitor List Mode

Step1: Check the checkbox to enable Black List Mode.

Step2: Schedule Settings. You can draw the schedule by clicking Edit button.

Step3: Set Alarm Action.

Step4: Set Alarm Settings.

After that, when a license plate marked as “Black”, “White”, “Visitor” is detected, the camera will respond accordingly to your settings.

4. Professional LPR Liveview Interface

Milesight LPR camera supports professional LPR Live View interface. You can see the real-time license plate recognition results.

Note:

(1) Upgrade your device to corresponded firmware version.

Camera: V4X.7.0.74 or above.

Firmware download link: http://www.milesight.com/support/download#firmware

(2) If there is no SD card or NAS as the storage space, the snapshots of license plate will be temporarily stored locally on the PC, cleared after logging out, and do not support Smart Search which will be introduced in the next part.

5. Smart Search

Step1: Select Plate Type or directly enter the license plate number.

Step2: Select Start Time and End Time, click the “Search” button to achieve fuzzy search, then the corresponding license plates or license plates containing search keywords will be shown on the logs while the complete video and license plate information will be shown on the left of the interface.

Step3: Set Alarm Action.

There are two methods to backup LPR logs.

(1) Backup license plates you want.

Step1: Tick license plates you want to backup and click “Backup” button ;

Step2: Select the export file type, video stream type and video file format, then click “Export” button.

(2) Backup all.

Step1: Click “Export All” button;

Step2: Select the export file type, video stream type and video file format, then click “Export” button.

You can also click the “Auto Export” button to automatically export the logs to FTP, SMTP or Storage.

Note:

(1) Insert available SD card or add NAS to camera as storage. Otherwise, you can’t check the LPR recording and snapshots.

(2) Upgrade your device to corresponded firmware version.

Camera: V4X.7.0.74 or above.

Firmware download link: http://www.milesight.com/support/download#firmware

V. How to set ANPR with Milesight NVRs

1. Preparation

Here are some notes you should notice before using ANPR function.

(1) Insert available HDD or add NAS to NVR as storage. (Otherwise, you can’t check the recording and logs.)

(2) Upgrade your device to corresponded firmware version.

Camera: V4X.7.0.72-r16 or above.

NVR: V7X.9.0.7-r7 or above.

Firmware download link: http://www.milesight.com/support/download#firmware

(3) Ensure your device support LPR/ANPR function.

Model of NVR:

• MS-N1009-UT / MS-N1009-UNT

• MS-N5008-UT / MS-N5016-UT

• MS-N7016-UH / MS-N7032-UH (16 ANPR Channels)

• MS-N8032-UH / MS-N8064-UH (16 ANPR Channels)

• MS-N1009-UPT

• MS-N5008-UPT / MS-N5016-UPT

• MS-N7016-UPH / MS-N7032-UPH (16 ANPR Channels)

Name of LPR Camera:

• LPR H.265⁺ Mini Bullet Camera

• LPR H.265⁺ Vandal-proof Motorized Mini Bullet Camera

• LPR H.265⁺ Pro Box Camera

• LPR H.265⁺ Motorized Pro Bullet Camera

• LPR H.265⁺ AF Motorized Pro Bullet Camera

• LPR H.265⁺ Mini PTZ Bullet Camera

(4) Ensure that NVR can get license plate information. Please set TCP as Post Type which is the default mode. It can be set in Camera web page -> Advanced Settings -> ANPR -> Settings interface.

2. Settings

Step1: Go to “Event”->“ANPR”, select a channel and enable ANPR function.

[License]: A license will be automatically assigned to each device.

[License Status]: This column is used to display the status of the license, “Valid” or “Invalid”.

[Processing Resolution]: Default resolution selected is 1280*720. You can choose different resolution according to the network environment.

Step2: Set ANPR function effective time. You can draw the schedule by clicking “Edit” button. Draw the schedule and then click “OK” or “Apply” after finishing setting.

Step3: Set detection parameters including Detection Trigger, Repeat Plate Checktime and Features identification.

[Detection Trigger]: Always and Alarm Input are available. It will only detect when alarm input is triggered if you select Alarm Input.

[Confidence Level]: You can set the confidence level from 1 to 10. When the confidence level of the license plate is higher than the set confidence level, it will push the license plate image to the logs interface..

[Repeat Plate Checktime]: The same license plate information won’t be received on NVR within the time you set.

[Feature Identification]: Check Region, Direction, ROI_ID or All to enable Features Identification, it will display the corresponding information on the logs interface.

Notes: Region detection only supports DACH region.

Step4: Set the detected ROI region which can be up to 4 regions. License plate will only be detected in the ROI regions.

3. List Management

Make a license plate list for your own NVR ANPR system.

Upload license plates and set them with different license type here. 10000 License plates can be added at most.

Kindly note that the list is exclusive for NVR, working with all LPR cameras you add. It won’t synchronize with the list on camera side.

There are two methods to add license plates:

(1) Add one by one.

Step1: Click the “Add” button.

Step2: Input the license plate and select license type.

Step3: Click OK and then the license plate will be added into the list.

(2) Batch upload by importing template.

Step1: Click Download Template button, select USB device folder and click OK to download Template.

Step2: Input all license type and license plate number as Template shows.

Step3: Click Import button, select the file and click OK to add all license plates into list.

4. Black/White/Visitor List Mode

We provide you three modes for better event management.

Black List Mode: Manage event for license plates in black list.

White List Mode: Manage event for license plates in white list.

Visitor Mode: Manage event for those license plates do not have license type.

Steps for settings:

Step1: Enable Black List Mode/White List Mode/Visitor Mode as your demand.

Step2: Set effective time for the mode to work.

Step3: Set actions you need including Audible Warning, Email Linkage, Event Popup, PTZ Action, Alarm Output and Trigger Channels Record.

Notes:

Do not forget to enable these modes, set effective time and record action for corresponded mode, so that you can get real-time video when license plate is detected (Effective time and record action is enabled by default.). You can refer to How to check ANPR record part for detailed record settings.

5. Professional LPR Liveview Interface

At the beginning, you need to switch the preview mode to ANPR mode.

There are two methods to enter live view ANPR Mode:

(1) Right click the mouse and select ANPR Mode as preview mode.

(2) Select ANPR Mode on live view bottom tool bar.

After entering ANPR mode, the real-time license plate information will be shown on the left of the interface once it get detected.

License plate information includes Plate Snapshot, Channel Name, License Plate Number, Detected Time and Plate Type.

Two License types:

No License plates type will be shown if the license plate does not exist in Black/White list. However, you can right click the license plate information to quick add it to Black/White list or delete it from Black/White list.

Besides, you can click the license plate information to check the latest X seconds (10s~20s) video.

Notes:

• X = 10 + Pre Record Time

   You can set Pre Record Time in Storage -> Video Record -> Record Settings interface.

• Make sure that HDD is available on NVR and correct record settings is made, so that you can check the record on live view. Please refer to How to check ANPR record part for detailed record settings.

• Make sure that NVR can get the license plate information. Please set TCP as Post Type which is the default mode. It can be set in Camera web page -> Advanced Settings -> ANPR -> Settings interface.

6. Set/Check ANPR Record

Before checking recording files, please make sure that you have proceed correct settings to make record action work.

(1) Set Recording

Step1: Set Smart Analysis as Record Type in Storage -> Video Record -> Record Schedule interface.

Step2: Enable Black List Mode / White List Mode / Visitor Mode as your demand.

Step3: Set Effective time and Trigger Channels Record action of your selected mode (Full effective time and trigger channel record are set by default).

Then NVR will record when license plate is detected.

Notes:

Generally, record action is triggered by event. If you just enable ANPR function without enabling Black List/White List/Visitor modes nor setting record action, it means you just enable the function while record action is not set. Then no record will be triggered. So it is necessary to do all above three steps if you want to trigger record action.

(2) Check recording

In Playback

Step1: Entering Playback -> Event Playback -> Smart Analysis interface.

Step2: Input corresponded information and click search button to search.

Step3: Click record to play the video searched out.

In Live View

Click the license plate information to check the latest X seconds (10s~20s) video.

Notes:

• X = 10 + Pre Record Time

   You can set Pre Record Time in Storage -> Video Record -> Record Settings interface.

• Make sure that HDD is available on NVR and correct record settings is made, so that you can check the record on live view. Please refer to How to check ANPR record part for detailed record settings.

7. Check/Backup ANPR Logs

(1) Check ANPR logs

Step1: Search on Smart Analysis interface.

Step2: Input corresponded information and click search button to search.

Then you will get a whole ANPR logs list.

License plate snapshot will be shown on the logs list while the complete image video and license plate information will be shown on the left of the interface.

Step3: Click the Play button to play the video

(2) Backup ANPR logs

Two methods are available after searching ANPR logs out.

Backup license plates you want.

Step1: Tick license plates you want to backup and click backup button.

Step2: Select the export file type, video stream type and video file format, then click export button.

Backup all.

Step1: Click backup all button.

Step2: Select the export file type, video stream type and video file format, then click export button.

Then you will get corresponded file as selected export file type.

VI. How to set ANPR with Milesight CMS

1. Preparation

(1) Refer to the NVR section

(2) Upgrade your CMS to corresponded version.

CMS: V2.4.0.7 or above

Download link: http://www.milesight.com/support/download#software

2. Settings

Step1: Add NVR to CMS.

Step2: Go to “Device Config”, select a NVR and the channel, then enable ANPR function.

[License]: A license will be automatically assigned to each device.

[License Status]: This column is used to display the status of the license, “Valid” or “Invalid”.

[Set LPR Detection Region]: You can set up to 4 ROI areas by drawing the screen. License plate will only be detected in the ROI regions.

[Processing Resolution]: Default resolution selected is 1280*720. You can choose different resolution according to the network environment.

Step2: Set ANPR function effective time. You can draw the schedule by clicking “Edit” button. Draw the schedule and then click “OK” or “Apply” after finishing setting.

Step3: Set detection parameters including Detection Trigger, Repeat Plate Checktime and Features identification.

[Detection Trigger]: Always and Alarm Input are available. It will only detect when alarm input is triggered if you select Alarm Input.

[Confidence Level]: You can set the confidence level from 1 to 10. When the confidence level of the license plate is higher than the set confidence level, it will push the license plate image to the logs interface..

[Repeat Plate Checktime]: The same license plate information won’t be received on NVR within the time you set.

[Feature Identification]: Check Region, Direction, ROI_ID or All to enable Features Identification, it will display the corresponding information on the logs interface.

3. List Management

Make a license plate list for your own NVR ANPR system.

Upload license plates and set them with different license type here. 10000 plates can be added at most.

Kindly note that the list is exclusive for NVR, working with all LPR cameras you added. It won’t synchronize with the list on camera side.

There are two methods to add license plates:

(1) Add one by one.

Step1: Click the “Add” button.

Step2: Input the license plate and select license type.

Step3: Click OK and then the license plate will be added into the list.

(2) Batch uploadadding by importing template.

Step1: Click Download Template, select folder and click OK to download Template.

Step2: Input all license type and license plate number as Template shows.

Step3: Click Import button, select the file and click OK to add all license plates into list.

4. Black/White/Visitor List Mode

We provide you three modes for better event management, which is based on two license types.

Black List Mode: Manage event for license plates in black list.

White List Mode: Manage event for license plates in white list.

Visitor Mode: Manage event for those license plates do not have license type.

Steps for settings:

Step1: Enable Black List Mode/White List Mode/Visitor Mode as your demand.

Step2: Set effective time which means Mode works during that.

Step3: Set actions you need including Audible Warning, Email Linkage, Event Popup, PTZ Action, Alarm Output.

5. Set ANPR Record

Step1: Set Smart Analysis as Record Type in Device -> Select NVR -> Record Schedule interface.

Step2: Enable Black List Mode / White List Mode / Visitor Mode as your demand.

Step3: Set Effective time and Trigger Channels Record action of your selected mode(Full effective time and trigger channel record are set by default).

Then NVR will record when license plate is detected.

Notes:

Generally, record action is triggered by event. If you just enable ANPR function without enabling Black List/White List/Visitor modes nor setting record action, that means you just enable the function while record action is not set. Then no record will be triggered. So it is necessary to do all above three steps if you want to trigger record action.

6. Check/Backup ANPR Logs

(1) Check ANPR logs

Step1: Search on Smart Analysis interface.

Step2: Input corresponded information and click search button to search. Then you will get a whole ANPR logs list.

License plate snapshot will be shown on the logs list while the complete image video and license plate information will be shown on the left of the interface.

Step3: Click Play button to play the video.

(2) Backup ANPR logs

Two methods are available after searching ANPR logs out.

Backup license plates you want.

Step1: Tick license plates you want to backup and click backup button

Step2: Select the Export File Path, File Type, Video stream type and Video file format, then click export button.

Backup all.

Step1: Click backup all button

Step2: Select the export file type, video stream type and video file format, then click export button.

Then you will get corresponded file as selected export file type.

VII. How to set ANPR with Milesight VMS Enterprise

1. Preparation

① Refer to the NVR section

② Upgrade your VMS Enterprise to corresponded version.

VMS Enterprise: V1.3.0.0 or above

③ Only the LPR cameras added by MSSP protocol support ANPR function for VMS Enterprise.

④ Make sure that VMS Enterprise can get the license plate information. Please set TCP as Post Type which is the default mode. It can be set in the Smart Analysis -> ANPR Settings -> Detection Settings interface.

2. Detection Setting

Here the configuration of the camera web side will be automatically obtained. If the camera web side is not configured, you can configure it in the interface of VMS. After the configuration is completed, it will be synchronized to the camera web side.

.

Step1: Select a camera in the devices list tree, then click  button to enable Detection.

.

[License]: Only LPR2 and LPR3 need to enter the license to activate the LPR function.

[License Status]: Show present license status, including Valid and Invalid. When the license status changes to be valid, the camera can start detecting the license plates.

[Process Resolution]: Resolution of the stream for LPR analysis, including 1920*1280, 1280*720.

Step2: You can click  button to enable LPR Night Mode. The LPR Night Mode supports the optimal LPR night recognition effect by adjusting different parameter levels. You can choose Auto Mode which can automatically switch to night mode according to illumination intensity, or choose Customize Mode to set effective time manually.

Auto Mode

Customize Mode

Step3: You can set up to 4 ROI areas by drawing the screen. If you choose Normal Mode, it supports configuring the LPR detection regions for the current area. If you choose Advanced Mode(Only for PTZ series), it supports configuring different LPR detection regions for different PTZ presets(Only support Preset 1~4 so far).   

Normal Mode

Advanced Mode (For PTZ camera)

Step4: Schedule Settings. You can draw the schedule by clicking  button, and then click  button after finishing the settings. 

Step5: Set Detection Settings and LPR Message Post Settings.

Detection Settings

LPR Message Post Settings

[Detection Trigger]: If you choose “Always”, camera will always detect the license plates. If you choose “Alarm Input”, camera will only detect the license plates during Alarm Input is being triggered.

[Confidence Level]: You can set the confidence level from 1 to 10. When the confidence level of the license plate is higher than the set confidence level, it will push the license plate image to the ANPR Search interface.

[Repeat Plate Checktime]: Set the time interval for repeatedly reading the license plates to effectively avoid duplicate identification of parking vehicles.

[License Plate Serial Format]: Formulate identification rules and automatically filter wrong license plates information to achieve more intelligent and accurate license plate recognition.

.

[Features Identification]: Check All, Direction, Direction Region or Region(Only for LPR2) to enable Features Identification, and the corresponding information will be displayed in the ANPR Search interface.

[Enable LPR Message Post]: Click  button to enable LPR Message Post. It will push information to some third-party devices or software that are compatible with ours. 

[Post Type]: Information can be pushed by RTSP, TCP or HTTP.

[HTTP Method]: There are two HTTP push methods: Post and Get.

[Snapshot Type]: Three kinds of snapshot can be chosen: All, License Plate and Full Snapshot. When you choose All, License Plate Snapshot and Full Snapshot will be pushed.

Note: This option is available just for Post HTTP Method.

[HTTP Notification URL]: The camera can use the API URL to send LPR information to other devices when the license plate is recognized. The API URL format is defined by the HTTP Server.

[User Name]: User name for HTTP Server.

[Password]: Password for HTTP Server.

[Camera LPR Port]: This option is available for TCP Post type.

Step6: Click  button to apply all settings.

3.ANPR Preview

After enabling Detection in the ANPR Settings -> Detection Setting interface, you can click  button in the right Function Panel, and the real-time license plate information will be shown on the right of the interface once it is detected.

.

The license plate information includes Plate Snapshot, Device Name, IP, License Plate Number, Detected Time and Plate Type. 

Two License types: 

—- License plate from Black List

 —- License plate from White List

No License plate type will be shown if the license plate does not exist in Black/White list.

You can right click on the ANPR notification push window to pop up a menu, and choose to add the license plate to White or Black List in the VMS system. If the license plate has already existed in the White or Black List of VMS system, then you can choose to change its type or delete the license plate from White or Black List.

Besides, you can click the license plate information to check the 20s video. (20s = the pre 10s + the post 10s of the license plate event)

Note:

Make sure that correct record schedule settings is made or the ANPR event rules are set to trigger recording, so that you can check the record in the ANPR Preview Panel. You can refer to 7(1) for operation steps.

4. List Management

Add the license plates as Black/White List as needed in the interface, and the license plates without the set types are the visitors. After enabling license plate recognition, VMS Enterprise will automatically receive the recognition result sent by the Milesight cameras and compare it with the black and white list added in VMS Enterprise.

1) Add license plates

You can choose either of the below two ways to add the license plates. 

a. Add license plates one by one 

Step1: Click  button to pop up a Add Plate window, then input the license plate and select the license plate type as black or white list, and click 

  button.

Step2: Repeat the Step1 to add other license plates manually.

b. Batch import license plates 

Step1: Click  button to pop up a Import Plates window. The imported file must be filled in according to the specified format. You can click  button to download the template.

.

Step2: After filling in, click  button to import the plates file, then click 

  button.

After successful import, you can click  button to modify the corresponding license plate and plate type.

Note: 

The format of the imported license plates file must be csv. 

The CSV must be saved in UTF-8 encoding format.

A license plate can’t be repeatedly added to the plate list. 

Maximum quantity of license plates added in the list is 10000. 

2) Search license plates

You can select the plate types including All, Black List and White List, or directly enter the license plate number, and click the “Search” button, then the corresponding license plates will be displayed in the list below. 

Note: The text searched is a case-insensitive contiguous string.

In addition, you can click  button to refresh the license plate list. And click  button to cancel the filter for the license plate list.

3) Export license plates

You can click  button to export the license plates in the current list to a csv form locally. If you filter the license plate list, only the filtered list will be exported.

4) Delete license plates

Click  button to delete all the license plates in the current list. If you filter the license plate list, only the filtered list will be deleted. You can also click  button to delete the corresponding license plate.

5. Black List/White List/Visitor Detection

Here you can set effective detection schedules for different detection modes, including Black List Detection, White List Detection and Visitor Detection. Only when the detection is enabled and the corresponding schedule is set, the corresponding detection results will be saved and can be viewed in the ANPR Search interface.

Step1: Click  button to enable the function, and then click  button to edit the schedule.

Step2: Click  button to apply the settings.

Step3: If you want to set related actions for ANPR trigger, you can refer to Method2 of 7(1) for operation steps. Then the set actions will be triggered once the corresponding license plate type is detected.

Step4: Once the ANPR event rules which you set take effect, you can check the ANPR event information in the Logs -> Event Logs interface. The event logs contain the event information about Date/Time, Event, Source, Action, Target and Details.

You can set filter condition as you need. In addition, if there is a recording video information about event, then you can click  button to check the event video.

6.ANPR Search

When the Black List/White List/Visitor Detection is enabled and the corresponding schedule is set, and the storage disk is enabled, you can view the corresponding detection results in the ANPR Search interface.

Step1: Check the cameras in the devices list tree, and select the plate type or directly enter the license plate number. 

Step2: Select Start Time and End Time, and click  button. Then the related license plate information will be displayed as below.

Click  button to show Thumbnail Mode.

Click  button to switch to List Mode.

Step3: Click on the thumbnail photo in Thumbnail Mode or license plate row in List Mode under the searched results, then the license plate details will be shown as below. If there is a recording video about the license plate recognition, then you can click  button to play the video or click 

  button to play the video in the playback interface.

Note:

Make sure that correct record schedule settings is made or the ANPR event rules are set to trigger recording, so that you can check the record in the ANPR Search interface. You can refer to 7(1) for operation steps.

Step4: You can click  button to backup the ANPR files you want to a local folder.

Step5: After setting the backup file destination, type and format, click  button to start the file backup. You can click  button to check task backup situation as below.

Note: 

The backup file of Plate List is csv format.

.

.

7. Set/Check ANPR Record

Before checking recording files, please make sure that you have proceed correct settings to make record action work.

Note: 

In the Settings -> System & Servers -> Server Settings -> Storage Management interface, make sure you enable the storage disk you are interested in to store recordings and images of VMS system.

(1) Set Recording

There are two methods to set the ANPR record.

Method1: The record schedule settings.

Step1: Select a camera in the devices list tree in the Settings -> Devices -> Camera Record Schedule -> Schedule interface, then click  button to enable Continuous Recording.

.

Step2: Set the Schedule, and then click  button to apply the settings.

Method2: Set the ANPR event rules to trigger recording.

Step1: Click  button to add the ANPR event rules in the Settings -> System & Servers -> Event Rule Settings interface.

Step2: Then select the trigger type as ANPR, set the source of trigger, and select the detection mode as your demand. And set the schedule and the Do Recording action. After setting the event rules, click  button.

Step3: Then the event rules will be added to the event rule list. Click   button to apply the event rules. The recording is triggered when the corresponding license plate type is detected. 

Note:

Make sure the corresponding detection mode is enabled and the detection schedule is set. You can refer to 5 for operation steps.

.

(2) Check Recording

a. Playback 

Step1: Select the camera in the Playback interface, click  button to select the time. 

Step2: You can check Show Event Mask to select the ANPR event, then the ANPR event videos will be displayed in the corresponding color.

Step3: Select the continuous recording or ANPR event recordings searched out on the time bar to play.

b. ANPR Preview

Click the license plate information to check the 20s video. (20s = the pre 10s + the post 10s of the license plate event)

c. ANPR Search

Click  button to check the latest 20 seconds video or click 

  button to play the video in the playback interface. (20s = the pre 10s + the post 10s of the license plate event)

.

<p>The post How to Set ANPR Solution first appeared on NVR IPCAMERA SECURITY.</p>

Safety Caution