By downloading the firmware from this web page you are agreeing to Hikvision’s Software User License Agreement. Please be aware that Hikvision products are region-specific and regionally supported. If you have purchased your Hikvision products from an online source or unauthorized distributor, they may not be compatible with the North American region’s firmware and are considered to be “gray market” product. If your camera has “CH” in the serial number, you are most likely using a “gray market” product. 

Updating the firmware from this site can lead to several complications in those cameras, up to and including camera failure.  Restoring a “gray market” product to its original condition is a factory process and will result in a Chinese interface. As Hikvision warranty is void in this case, you must rely on the dealer for any service, support, and warranty of the “gray market” product. If you have any questions or concerns about the official status of your Hikvision distributor, please contact Hikvision USA Customer Service at cust.usa@hikvision.com.

.

Upgrade Device Firmware

For a device added via IP/Domain, its new version can be detected by the Mobile Client. Once detected, you can upgrade the device to its latest version.

1.Enter the Device Information page.

• On the device list page, if the page is in the list mode, swipe the device name to the left and tap .

• On the device list page, If the page is in thumbnail mode, tap the device name or tap .

• On the Live View page. Tap  and then tap Settings.

Note:

For details about how to enter the Live View page, see Start and Stop Live View.

2.Tap  > Device Version to enter the Device Version page.

3.Tap Upgrade and then tap UPGRADE on the pop-up window.

The Mobile Client will download the upgrade file first and then start upgrading the device.

Note:

You can also enable the Mobile Client to automatically download the upgrade file in Wi-Fi networks once a new device version is detected. For details, see Auto-Download Upgrade File.

.

UPDATING FIRMWARE

Hikvision regularly updates the firmware in our products to resolve potential issues and keep your system running smoothly. Below, you can find guidance on how to update your system accordingly.

Updating Hikvision IP Camera Firmware

To upgrade the firmware of a Hikvision IP camera, please follow the steps below:

1.Locate the appropriate firmware by clicking this link

2.Click on the firmware, then click download.

3.Agree to the license terms and conditions when prompted.

4.Locate the downloaded firmware file (this typically will be in the default download folder, unless prompted for a download location, then choose Desktop) and extract it by right-clicking on the file and selecting extract all or unzip. When prompted for an extract location, choose Desktop to extract the final file to. A file labeled DIGICAP will appear on the desktop.

5.After the file is extracted, log into the camera using Internet Explorer or Firefox web browsers. If prompted to install the plugin (or to allow the plugin to run), follow the prompt to proceed with the upgrade procedure.

6.Log into the camera using the administrator username and password, then go to the Configuration tab. In this tab, go to Basic Configuration then System, and then click on the Maintenance tab.

7.On the bottom of the page under Remote Upgrade, press the Browse button to locate and choose the firmware file, which was previously saved on the Desktop. After selecting the file, click Open, then click Upgrade.

8.The camera will display a prompt that a reboot is necessary to complete the upgrade. Click OK. The camera will reboot when the firmware is successfully upgraded.

Click here to see a video tutorial of the above steps.

Upgrading Hikvision DVR/NVR Firmware

To upgrade the firmware of a Hikvision DVR or NVR, please follow the steps below:

1.Insert a USB flash drive into the computer’s USB port (Please note that the USB flash drive does not need to be empty; it may contain other files and documents).

2.Locate the appropriate firmware by clicking this link

3.Click on the firmware, then click download.

4.Agree to the license terms and conditions when prompted.

5.Locate the downloaded firmware file (this typically will be in the default download folder, unless prompted for a download location, then choose Desktop) and extract it by right-clicking on the file and selecting extract all or unzip. When prompted for an extract location, choose the USB flash drive (typically labeled by letters E, F and so on) to extract the final file to. A file labeled DIGICAP will appear in the USB flash drive.

6.After the firmware has been extracted (unzipped), remove the USB flash drive from the computer and insert it into one of the available USB ports on the DVR/NVR unit.

7.On the DVR/NVR, go to the Main Menu, and then go to Maintenance.

8.From the sub-menus on the left click Upgrade. This will display the content of the USB flash drive.

9.Choose the DIGICAP file and press Upgrade.

10.An information window will pop up prompting that the unit will reboot after the upgrade is complete. Click YES.

11.To verify that the firmware has been upgraded, after the DVR/NVR is rebooted, go to the Main Menu, and then go to System Information. The current firmware version will be displayed.  

New Hikvision Firmwares 2024

Also Read : Hikvision How To Tutorials Chapter 1

How do I get Firmware Updates for my Hikvision Gear?

Hikvision Australia’s website has firmware updates for available IP cameras.
https://www.hikvision.com/au-en/

Use the search bar to try and find your product. Firmware updates are usually available on the product page.

IF YOU BOUGHT EQUIPMENT FROM US:

You will need to contact us if you can’t find your camera listed or if you require firmware for your NVR / DVR.
You will need to also provide the full serial number of the device as well as your current firmware.
This is to ensure upgrades are done properly. In some instances middlle firmware is required before upgrading to the latest version.

We do not recommend doing intercom firmware upgrades. Please check with us if there is any doubt.

If you didn’t buy equipment from us, please contact the people who you bought the equipment from.

How to Upgrade Camera Firmware via Hikvision NVR

This Video shows you how to upgrade your Camera firmware from the NVR.

Hikvision Australia’s website has firmware updates for available IP cameras.
https://www.hikvision.com/au-en/Support/Downloads/Firmware/IPC

NOTE this is only for IPC.

You will need to contact us if you can’t find your camera listed or if you require firmware for your NVR / DVR.
You will need to also provide the full serial number of the device as well as your current firmware.
This is to ensure upgrades are done properly. In some instances middlle firmware is required before upgrading to the latest version.

We do not recommend doing intercom firmware upgrades. Please check with us if there is any doubt.

 .

Lates Hikvision Firmwares 2024

How do I update Hikvision firmware remotely for my TetherX installation?

If your system was installed by one of our security installation partners please contact them to update your cameras. If you would like to update your Hikvision devices yourself please follow the guide below.
​

.

1.Download the latest Hikvision firmware by visiting the Hikvision Downloads Page

Hikvision Downloads Page

Note: the UK firmware is different from the US firmware. For UK firmware, please follow use the UK Downloads page.
​
​

2.Extract the firmware archive, it should contain the file: digicap.dav

3.Create a tunnel into your Hikvision device.

How to create a tunnel?

​

4.Login to your Hikvision device and navigate to “Configuration” then “Maintenance”.

​

5.At the bottom of the page under the ‘Upgrade’ header, press on “Browse”

​

6.Use the file navigator window that pops up to select the digicap.dav file you downloaded earlier
​

7.Click on ‘Upgrade’

.

The actual upgrade will take up to 10 minutes and the device will automatically reboot at the end of the upgrade process.
​
This video from Hikvision Technical Support shows the upgrade process:

.

Click here to see a video tutorial of the above steps.

00 Temperature Screening-2020-07-10

01 Density Control-2020-07-10

02 Mask Detection-2020-07-17

03 Front Ends-2020-12-02 

04 Back Ends-2023-03-15

Access Control & Video Intercom-2020-12-02

Accessaries-2021-12-01

Alarm-2023-06-21 

ANPR & Speed Radar Display-2023-07-10

Dell image-2022-12-12

Mobile-2023-07-03 

Paxton related materials-2023-05-26

Portable Series-2024-02-06 

Thermal-2023-07-07 

Transmission & Display-2022-12-16

.

DVR-2023-08-11 

IPC-2021-11-04 

NVR-2021-11-26 

PTZ-2021-09-23 

fw and model list.xlsx10.27KB2019-04-09

.

.

.

.

.

Hikvision Firmware Download –
Intelligent Traffic Products

.

Hikvision Firmware Download –
Access Control Products

.

.

.

.

.

.

<p>The post New Hikvision Firmwares 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Access from smartphone

(1)Download APP

Search and download “Eseecloud” app from App store or Google play on your phone.

.

(2) Register

 If you install and open “Eseecloud” app at the first time, an account need to be registered initially.

ce”.

.

(3) Add device

Method 1: Add the device via QR code.

EseeCloud Devices Advanced User Guide

Read Next : EseeCloud Wireless Security Camera System Installation.

.

Method 2: Add by cloud ID.

     Cloud ID: Enter NVR’s System Setup – Network Setup to input Cloud ID or Scan QR Code)

     Device name: Choose a name for your system of your choice.

     User Name: Enter the NVR’s User Name (default: admin)

     Password: Enter the NVR’s Password (default: NO password)

.

.

Method 3: Add by LAN scan.

Please make sure you are connected to the same wifi.

.

Access from remote PC

1. Access from remote PC (Log in with Cloud ID)

Operation Steps: ( We suggest you to use microsoft IE, otherwise some services will be invalid. )

1. Open your browser

2. Enter http://www.e-seenet.com

.

Cloud ID: (Enter NVR’s System Setup-Network Setup to input ID or Scan QR Code)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

3. Enter the correct device ID, user name and password.

4. Click login to enter live view interface.

.

Note: To successfully remote access your system, the device ID should be ONLINE.

.

2. Access from PC Client (CMS)

1. Please download CMS from the below link:

http://www.tontonsecurity.com/download/page_show_67.html

2. Login user: admin, password: (default: NO password, please keep it blank)

3. Please enter “Add” to add device, you can add it “By IP/DDNS” or By Cloud ID”

4. By IP/DDNS:

IP/DDNS: (Enter NVR’s System Setup-Network Setup to find IP)

Port: (default: 80)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

Device name: Choose a name for your system of your choice.

Type: choose “NVR”.

Number of Channels: please input the correct number of the channels.

Click “Finish” and go back to “Preview”, click the device name to view live video.

5. By Cloud ID:

Cloud ID: (Enter NVR’s System Setup-Network Setup to find IP)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

Device name: Choose a name for your system of your choice.

Type: choose “NVR”.

Number of Channels: please input the correct number of the channels.

Click “Finish” and go back to “Preview”, click the device name to view live video.

Add the IP camera to the NVR by matching code

1.  When you use Match Code
1.1 Add new add-on cameras to your system
1.2 Re-pair camera to NVR when they lose connection. You need to delete the
Network Unreachable channel at first, then re-pair the camera to an unoccupied
channel. (unoccupied channel always shows No Video Source under Status.)

Tips: The IP cameras in pre-packed kits have already been paired to the NVR. So the
cameras will automatically connect to the NVR once they are plugged in power.

2.  Add camera by matching code.
2.1  Power on the camera which has no video, and connect this camera to the NVR
via Network cable.

.

2.2  Right click mouse on the main interface, select “Video Manage“

2.3  Click “Refresh“, find the camera’s IP. Click “Match Code“, then click “Yes“, the
NVR will start to match code to the camera.

.

2.4  After matching code successfully, the “status” will show “Connect success“.

Then you will see the camera is added to the NVR and display video on the screen.

.

What is the WiFi distance of the wireless kits?

.

Between each camera to the NVR:

In open space we tested 350m (1150ft) working distance;

With normal obstacles like 1-2 walls, we tested 35m (115ft) working distance.

For distance we only have theoretical values.

No certain distance can be guaranteed due to different environments applied in.

It varies depending on obstacles and signal interference.

on the contrast, if there are many blocks and signal interference between, the distance could be closer. 

.

What if your NVR system keeps beeping?

1. Please right click your NVR mouse, then click System Setup – General Setup – Error setup, make sure that “Enable” and “Buzzer” are unchecked.

2. Please right click your NVR mouse, then click System setup – Channel setup –  Video detection, make sure that “Buzzer” is unchecked for all channels.

3. If you have checked above 2, and none of the buzzer are checked.

    Follow below to stop the beeping:

    a. Right click your NVR mouse, then click System setup – System Admin –  Factory setting, uncheck WiFi Reset, then click Apply to reset NVR settings.

    b. If you cannot view the cameras on the NVR after resetting, please right click your NVR mouse, then click Exit system, choose shutdown. Follow on-screen message to unplug NVR from power and then re-plug it back to NVR. Wait for NVR to initialize.

Then the cameras shall come back.

.

How to upgrade the NVR system

.

.

1. Please download the update file to your computer and unzip it, then plug the USB flash drive,and move the unzipped update file to the root directory of the USB flash drive. 

Note: 

1)Please move the update file to the root directory of the USB flash drive, do not move the subdirectory.

2)Do not change the file name.

.

.

2. Connect USB-disk/mouse and USB hub with NVR shown as flowing.

.

.

3. Enter the NVR’s menu (System setup\System Admin\System upgrade),
Click “Start” to begin upgrading.
.

Note: Please keep power supply well during the upgrade.

.

.

4. Once the upgrade is done, NVR will restart system automatically.

.

.

How to view playback on NVR system

.

1. Right click the mouse , choose video playback

.

2. In the menu bar on the right, choose record type/channel/data to search what
you want to and click playback.

.

3. Click Backup and the video will be saved in USB storage

.

How to Add C8601 Cameras to Tonton NVR System

.

Document

.

or

.

Video

.

How to connect and set up the Wireless Network Camera System?

.

.

1. Connect the DC 12V/2A power adapter to the Power port of the NVR.

When Power indicator light is on, NVR starts to work.

2. Use VGA / HDMI cable to connect your NVR and Monitor / TV, then preview interface can be seen.

3. Plug the network cable and mouse to the ports of NVR rear panel.

4. Connect the DC 12V/1A power adapter to the IP camera (IPC).

Each camera has one 6ft length power adapter.

5. After finish connecting, the NVR will search the IPC automatically and start to initialize the connection.

When completed connection, the images will display.

6. Login this system:

Username :  admin

Password:  (there is no password, please keep it blank)

(Note: if you want to change the password, you can go to NVR’s System Setup – System Admin -User management – Set password to change it.)

7. Then you can follow up the below steps to set up on your phone:

If you want to view the cameras remotely, the NVR should be connected WAN network, Please ensure DHCP in your Router is open.

If you don’t know how to enable the Router’s DHCP, please input the IP Address of your  

Router to IE browser, then you will find the network information, you can enable the “DHCP”.

After that, please go to NVR’s System Setup – Network Setup to enable “DHCP”

Then the system will obtain the IP Address, DNS from your Router automatically.

Or you can go back main menu to select “Fast Network”, Then the system will connect the WAN network automatically.

8.   Access from smartphone

(1). Please download “Eseecloud” app from App store or Google play on your phone.

    (2). If install and open “Eseecloud” app at the first time, an account need to be registered initially.

(3) Add the device.

Method 1: Add the device via QR code.

.

.

Method 2: Add by cloud ID.

Cloud ID: Enter NVR’s System Setup – Network Setup to input Cloud ID or Scan QR Code)

Device name: Choose a name for your system of your choice.

User Name: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

.

.

.

Method 3: Add by LAN scan.

Please make sure you are connected to the same wifi.

.

.

9. Access from remote PC (Log in with Cloud ID)

    PC : our item only support IE browser, please input “www.e-seenet.com” to IE Browser to view your cameras.

       Cloud ID: (Enter NVR’s System Setup – Network Setup to input ID or Scan QR Code)

       Username: Enter the NVR’s User Name (default: admin)

       Password: Enter the NVR’s Password (default: NO password)

(Input the correct Cloud ID, user name and password, click login to enter live view interface.)

.

NVR video backup.

1.Right click mouse > select Video backup.

.

2. Enter into the interface of Video backup.

   Select Channel, Record mode and Search time.

   Click “Search”. After that, the chosen video will display in the list.

3. Select the section which you want to backup.

   Then, click the bottom “Backup”.

4. Next, there will pop up a dialog box asking are you sure to backup this record.

   Click “Yes” if you are sure.

   Before start to backup, system will inform you to insert U disk within one minute. 

   If you want to cancel the operation of backup, you can click “Cancel” to withdraw.

   NOTE: The NVR only one USB port, so you have to unplug the mouse

and plug the U disk within one minute.

5. After you insert U disk, what you should do is just wait a moment.

6. Backup is completed when system inform you “Backup record succeed“.

   And you can unplug your USB disk at that time.

.

How to setup audio function?

1. System connection

(1) The monitor must have HDMI input port.

  (2) Connect the HDMI port on both sides with the included HDMI cable.

2. NVR setup

  (1) Choose the option “Private” on this interface during NVR’s restarting. It allows you select audio or not.

(2) Check whether the encode mode is “AV stream” or not.

(3) On the live window, click mouse to select any channel to pop-up the hidden volume icon like a speaker, click it repeatedly to hear or mute the sound from camera.

.

How to use a new Gmail mailbox account to set NVR mail alarms?

How to use a new Gmail mailbox account to set NVR mail alarms?

1.Register a new Gmail mail account, and log in.

2.Get into your mailbox>click the “” in top right of page>get into “My Account“.

3.     Click “Sign-in&security” and enter the interface,Turn on “Allow less secure APP on“.

4.  After that, you will receive an email from Google, which means “less secure sign in” has been turned on.

5. Get into NVR system. Right click mouse>select System setup>Network setup>Network Status.

   Check if your NVR’s network connected successfully.

   Before operate what mentioned above:

    Make sure Cloud(P2P) display “ONLINE“.

   Make sure the Network Status display “Healthy Network“.

6.Then, click the “E-Mail”. 

Input your Gmail SMTP Server (smtp.gmail.com) in ” SMTP Server” Input your Gmail account in “Username” and “Sender”.

Change the “Encryption Type” to “TLS”.

Input your Gmail password in “Password”

Input your two inbox address in “Sendee 1\2” 

After that, click “Apply”>click “Test”.

7.        When the system remind you “Test successful”, which means NVR’s mail alarm is set successfully.

8. PIR video detection setting as below picture:

    (1). Click “Channel setup” and “Video detection”

    (2). Choose Motion Detection, disable it

(3). Choose PIR Input Armed Detection, Enable E-mail Notice

9. After finished setting, When alarm is triggered, you will receive email from NVR.

PIR alarm setting

Only PIR detection recording setup

1.      Disable motion detection function, click ok to save

2.      Choose Detection Model with PIR Input Armed.

Please noted: If you want to set Buzzer, Email notice or App alarm, you can enable them, in this way, you will get notification on email or App.

3.      Press “Reset” to clear default setting

.

4.      Click the icon “Alarm”

5.      Press and drag the left button of the mouse to select needed schedule.

6.      Click ok to save

7.      Cancel the manual recording mode

.

.

.

8.      Once the PIR detection is trigged, the live window will display an icon like below, it means PIR recording is running

.

How to Reset NVR’s Password

Reset NVR’s Password

1. The interface when you log in. 

 2. Click “OK”. If you input incorrect password,

     monitor will display “Username/Password Is Incorrect!”.

 3. Continuously and successively click left button and right button in blank space of prompt box for six times.After that, monitor will display “Restore default user”.

4. Click “Yes”, and you will access to the interface where you can reset NVR’s password.

Tips:   1. The username must be “admin”, or else the password won’t be retrieved.

           2. If you want to make new password, please leave it blank in column of “Old password”.

           3. Delete the old password after reset the new one.

           4. If you have set a new password for NVR, remember that NVR password cannot exceed 10 characters, or the NVR will not save it correctly.

.

 reset NVR’s password             click to download video

How to install iSmkit PC client 

.

How to install iSmkit PC client                  Click here to download

Gmail Mail Configuration Guide

(DE) Gmail Mail-Konfiguration Anleitung 

click here to download

.

(FR) Guide de configuration de Gmail Mail 

click here to download

.

(CN) Gmail邮件配置指南操作步骤20230922

click here to download

.

(EN) Gmail Mail Configuration Guide 

click here to download

.

Email SMTP and POP3 settings

.

click here to download

.

Solve the problem of the white light always on(Applicable to 3.6.60 and above Version)

Precautions:

1. Please check your IPC version first, only 3.6.60 and above version can be solved the problem through upgrade.

2. The camera must be able to produce the image, if the camera can’t be viewed or resetted, it can’t be upgraded.

.

Check IPC Version:

Go to “System Admin” – “IPC Maintenance” to check the version of the problem camera. Please note: Don’t upggrade the version 3.6.16 and below version with these upgard file.

.

Download the upggrade file:

For 3.6.60 Version: Download Link

For: 3.6.60 Above Version: Download Link

.

Upgrade Method

1. Upgrade the IPC via NVR system

（1）Please download the update file to your computer and unzip it, then copy the update file(IPCAKV3C_xxxxx.rom) to a USB flash drive. Please note: Don’t change the file name

（2）Plug the USB flash drive to the NVR’s USB interface

Enter the NVR’s menu (System Setup-> Channel Setup-> IPC Upgrade)

.

.

（4）Click the “Channel” and select the upgarde channel of the IPC.

.

（5）Click “Start” and “Yes”, the IPC will be upgrading. Please note: During the upgrade, please don’t power off the NVR and the camera.

.

.

（6）If the camera upgraded successfully, the Status will show “Success!”.

.

.

2. Upgrade the IPC via TF card.

.

.

（1）Unzip the upgrade file, then copy the “help.rom” file to the TF card. Please don’t change the file name and move it to the root directory, do not move the subdirectory.

（2）Power off the camera, then insert the TF card to the TF card slot. Then power on the camera.

（3）Waiting for about 1 minutes, the camera will start up. Then press 3 times continuously of the reset button for the camera(In order to prevent operation errors, you can press several times, which will not affect the upgrade).

（4）About 2 seconds later, the camera will makes a sound for an upgrade. Then waiting for about 2-3 minutes, if the camera restart and works normally, it means that the upgrade is successful.

New Manual for Dual light

Click here to download

If the IP camera doesn’t work with NVR system,please check …

1. First of all,please confirm both of the camera and the NVR are powered on .

(1) Camera is powered on: Please plug the power adapter to the camera ,and then cover the IR-Cut with your hand (See picture), finally to check if the night vision will be activated or not .

(2) NVR is powered on : Please plug the adapter to the NVR ,and then see whether the power indicator is on.

.

.

.

.

2. Secondly please enter NVR system — Video Manage ,and check if the status of camera is connected successfully or disconnected. 

.

.

.

3. Thirdly, if the camera is disconnected,please confirm the distance of the camera and NVR system. The far distance will affect the signal transmission.Please follow the below steps to fix the issue:

.

(1) . Please enter NVR system —  Video Manage — delete camera (The same page as the Step 2)

(2). Remove the camera and take it next to the NVR system,and prepare a network cable and start to match code for the camera and the NVR.

(3). How to Match code :

A. Connect this camera to the NVR via Network cable.

B. Right click mouse on the main interface, select “Video Manage“

C .Click “Refresh“, find the camera’s IP. Click “Match Code“, then click “Yes“, the NVR will start to match code to the camera.

.

.

D. After matching code successfully, the “status” will show “Connect success“.Then you will see the camera is added to the NVR and display video on the screen.

.

4. Finally, you could unplug network cable and put the camera to the place where you want .

How to change the channel

.

.

1.Please click “Video Manage”.

.

.

2.Make a note of the camera IP address you want to change.

.

.

3.Click “Manual Edit” and enter the IP address on the corresponding channel.

.

.

How to fix black screen Monitor for 10” /15.6”NVR

click here to download the operation video

.

How to get the NVR system ONLINE?

.

1. Please make sure you enabled DHCP of your Router.

2. If you don’t know how to enable the Router’s DHCP,

    please input the IP Address of your Router to your computer browser,

    then you will find the network information, you can enable the “DHCP”.

3. After that, please plug a network cable to the WAN port on back of NVR.

4. If the system refuses to go ONLINE?

Basic troubleshooting:

  (1).  Check if your network cable can work well.

         If NVR is getting signal, there should be flash light. If not, please check the connection and cable.

  (2).  If the port is right and NVR is still OFFLINE, then it should be DHCP issue.

         Enable DHCP on your NVR.

        Click right button of mouse, go to NVR’s System Setup – Network Setup – check the DHCP and enable it,

        apply and save it. Wait for 1 minute to see if the status on bottom right corner changes to ONLINE.

5. Or you can go back main menu to select “Fast Network“, 

        Then the system will connect the WAN network automatically.

        Within 1 minute, you shall see NVR status changes to ONLINE and the NVR is ready to be viewed

        from anywhere anytime.

6. If this can’t help you, probably your Router disabled DHCP or block new devices from connecting.

    What DHCP does is: when Router find new device connected, DHCP allocate new IP to the device

                              and connect it to the Internet.

   An easiest way to know if your router enables DHCP:

   When you connect a new device to your WiFi for Internet service (or a visitor/ friend wanted WiFi

   connection), does it require WiFi password only? If only password required, then your router has

   DHCP enabled; if that requires not only password but also some settings, then your Router is secured

   from connecting new devices. Please ask people who secured the WiFi (who set password) to enable

   the NVR to connect.

The Step 4 and Step 5 should enable 95% users to get NVR ONLINE.

Even if the status shows OFFLINE after all this, we suggest you to use APP and access the Cloud ID

to see if it works.

Note:   Always wait for 1 minute after any change.

.

Advanced troubleshooting

If the basic steps above does not solve the issue. Follow below steps to do further troubleshooting.

1. Make sure the cable you connect to NVR has Internet access. 

Please use a laptop or any PC has RJ45 port

· Disable the wireless connection of laptop.

· Unplug the network cable from NVR and plug it into the PC, see if the PC can access the Internet via the cable.

· If it does, then the cable is good; if it does not, change a cable.

· If cable is good yet no Internet connection, please ask help from your network administrator

· to give the cable Internet access.

2. Enable DHCP of your router, please refer to Step 2.

.

If you don’t want to use DHCP, or you want to set up a static IP Address for your NVR system,

you can follow the below steps to set up:

   Well, we can allocate IP manually for the NVR and connect it to Internet. 

  1. Know your router gateway. 

  This is the IP that goes to the menu of your router. 

  This will vary slightly from manufacturer to manufacturer, and will be listed in the documentation.

  Here are some common IP addresses for various routers:

   Linksys, 3Com, Asus, Dell, US Robotics: 192.168.1.1

   Qwest (AKA CenturyLink), DLink, Netgear, Trendnet, Senao: 192.168.0.1

   Belkin, Microsoft, and SMC: 192.168.2.1

   Apple: 10.0.1.1

If you have misplaced your documentation, and you do not see your router listed here,

search on Google for your router name and “default IP address” to find the correct information.

Another way to locate your router’s IP address: on a PC, open the command prompt (click on Start >

Run/Search for cmd) and enter ipconfig. Look for the Default Gateway line, and try that number.

On a Macintosh, open the Network control panel (System Preferences…, Network) and look for Router: 

This is your router’s IP address.

2. Go to NVR’s System Setup Network Setup

How to switch wireless connection to wired connection

.

.

1. Please connect IP camera to NVR by net cable

2. Checking the Network setup of NVR, remember the network segment of the IP address with NVR

.

.

3.Right click mouse, Enter into VIDEO MANAGE

.

.

4.Click Refresh, search the IP address of camera which connect to NVR

.

.

5.When you find the IP camera on NVR, please click Modify, revise the IP address of camera to the same network segment with NVR

Please noted: The IP address of camera can’t conflict with the IP address of other devices

.

.

.

.

Click Yes to save

.

.

Double click the IP address, the camera will connect to NVR automatically

.

.

6. After setting the IP camera, connect NVR and the IP camera to the same router by net cable, Refresh NVR, search for the IP camera, then add it to NVR, in this way, the IP camera will connect to NVR by wired

.

When 3MP IPC is added to NVR, it prompts “resolution too big”

.

.

When adding a 3MP camera to the NVR, if the “resolution is too large” prompt appears.Please modify the NVR resolution, the detailed operation is as follows:

.

1.Please click “Video Manage”.

.

.

2.Select the camera that appears “Resolution too big”, and then click “Channel Setup”.

.

.

3.In “Channel Setup-Encode setup”, modify the resolution to 1920*1080, and then click “Apply” to save the settings.

.

.

4.Disconnect the power of the camera and restart it, after adding the camera, the camera can be used normally.

.

.

Dual light and AI function setting instructions

Click here to download

.

iSmKit CMS user manual

Click here to download

.

How to upgrade the 8CH NVR to 10 Channel(Only for Version 3.1.8.0M)

.

.

1. Comfirm your system version if is the version 3.1.8.0M first. 

Note: This update file only supports NVR version(3.1.8.0M) to update to 10 channel, if your system version is not 3.1.8.0M, please don’t use this update file to upgrade your system, otherwise it will cause the system not work.

.

Go to “System Admin” – “System Version” to check.

.

2. Download the upgrade file to your computer. Click here to download

.

3. Unzip the upgrade file via rar or zip, then plug the USB flash drive, and move the unzipped update file to the root directory of the USB flash drive. 
Note: 
1)Please move the update file to the root directory of the USB flash drive, do not move the subdirectory.
2)Do not change the file name.

.

4. Connect USB-disk to the NVR.

.

5. Enter the NVR’s menu (System setup\System Admin\System upgrade), Click “Start” to begin upgrading.
Note: Please keep power supply well during the upgrade.

.

6. Once the upgrade is done, NVR will restart system automatically.

.

Effective Troubleshooting for Non-Functional 16-Inch Monitor

Effective Troubleshooting for Non-Functional 16-Inch Monitor

.

.

Youtube Video: https://youtu.be/QVtIkMScO0Q 

.

1. If the indicator lights in the bottom right are OFF, replace the monitor’s 3A power supply.

.

2. If the indicator lights in the bottom right are ON, but the screen is black, check the screen cable.

.

.

.

If the display shows “Power Saving,” there are two possible scenarios:

.

3. For “No Signal → Power Saving”:

When there is no signal, immediately press the “Auto” button. This will bring up the signal source selection menu. Use the “←” or “→” keys to navigate to the first option (“Auto select”), then press the “Menu” button to confirm.

.

4. For “No Cable → Power Saving”:

Please check the two connecting cables in these locations.

.

.

<p>The post EseeCloud Devices Advanced User Guide first appeared on NVR IPCAMERA SECURITY.</p>

We specialize in providing user-friendly security systems to ensure the safety of your home and business. Our mission is to protect your valuable assets and provide peace of mind through tailored security solutions.

At TIGERSECU, we value customer satisfaction above all else. Our knowledgeable support team is always available to assist you with any inquiries or technical support needs. We are committed to exceeding your expectations and ensuring your peace of mind.

Whether you’re a homeowner or a business owner, TIGERSECU has the expertise and resources to meet your security needs. Join our growing family of satisfied customers and experience reliable security solutions.

TIGERSECU NVR XVR Firmware Upgrading Instruction

Read Next :

• NVR AI Function Setup Guide
• iViewer installation and user guide
• How to Upgrade NVR Firmware for Amcrest

TIGERSECU 5MP 8CH XVR Firmware Upgrading Instruction

Step 1: Prepare a USB flash drive and format it (USB 2.0 Standard is recommended).

Step 2: Download the firmware zip file to your computer from the following link:

https://www.tigersecu.com/xvrfw/xvr524_V6_2_82_180000.zip

Step 3: Unzip the downloaded file.

If you don’t have unzip software on your computer, you can download “7-Zip” from https://www.7-zip.org/ and install it first.

Right-click on the downloaded zip file, select “Open with 7-Zip,” and choose “Extract

files.”

Choose your computer’s Desktop as the destination for extracting the files and click OK.

Step 4: Locate the firmware file “KT_XVR524_L_V6.2.82.180000.update.update” on your computer’s desktop and copy it.

Step 5: Paste the firmware file into the root directory of the USB flash drive.

Step 6: Insert the USB flash drive into the USB slot at the back of the XVR.

Step 7: Access the XVR Main menu and go to the Upgrade menu.

Click on “Refresh” to detect the USB flash drive.

Main Menu

Upgrade

Upgrade From Local

File T

31 F Refresh 1

Upgrade

Choose the firmware file from the File field.

Click on “Upgrade” to initiate the firmware upgrade process.

Once the upgrade process is completed, the XVR will automatically reboot.

Please follow these steps carefully to ensure a successful firmware upgrade for your TIGERSECU XVR.

If you have any further questions or require assistance, please don’t hesitate to reach out to us at service@tigersecu.com or +1 323 315 0396 Monday to Friday, 9 am – 5 pm Pacific Time.

TIGERSECU H.265 2MP WiFi NVR Upgrading Instruction

• Upgrade from Cloud is Recommend.

To upgrade your NVR’s firmware through a Cloud Upgrade, it is necessary to connect the NVR to your network.

In the Upgrade settings, click Check to check for the latest available version of the firmware.

If an update is available for your NVR, proceed with upgrading your firmware.

If not, you will get a message that your NVR firmware is up to date.

• If you prefer upgrading from Local, please follow the steps below:

Step 1. Prepare a USB flash drive, format it firstly. (Recommend FAT32 USB 2.0)

Step 2. Download the firmware zip file from the below link.

http://www.tigersecu.com/firmwareh265/nvr_6.1.24.18.zip

Unzip the file. Copy the “kt_hi3536d_9920_MT7601_210401_nvr_6.1.24.180000_usb_2g_4_8_update.update”, and paste it into USB flash drive root directory. (Do not save it in a folder)

Step 3. Insert the USB drive into the USB slot at the rear of the NVR.

Step 4. Go to the NVR –> Main Menu –> Upgrade Menu, click Refresh. When the file in the USB drive is read –> Click Upgrade.

Step 5. After the upgrading is 100% completed, the NVR will beep and auto reboot. Wait 30-40 seconds for it restarting. Upgrading done!

H.264 HD 2MP 4CH(M_IX_HB) DVR Firmware(V20220331)

Important Tip:

1. Go to the DVR Menu bar > Information page to check your DVR Model. This firmware is for Model 4CH(M_IX_HB).

2. Please don’t try to downgrade your DVR to an older firmware version if your DVR is already [Version:8638000020220331] to avoid unknown failures in the DVR.

As always, feel free to email us at service@tigersecu.com with any questions. We’re here to help.

*Release – [Version: 8638000020220331]

• Upgrading Instruction-H.264 2MP Series 4CH(M_IX_HB).

Release notes:

This firmware will update your system to [Version: 8638000020220331] which has the following improvements:

1. Optimized system time zone settings

2. Supported playback timeline zoom function

3. Fixed some known issues

__________________________________

*Security note:

To ensure your ongoing privacy, we strongly recommend creating your own password from the all-access default password as soon as possible, if you have not already done so. Choose something that you’ll remember, but that other would be unlikely to guess.

Change your password at DVR Main menu > Configuration menu > User > admin: Edit > Password Setup.

As always, feel free to email us at service@tigersecu.com with any questions. We’re here to help.

H.264 HD 2MP 4CH(M_VIII_HB) and 8CH(M_VIII_HB) DVR Firmware(V20220331)

Important Tip:

1. Go to the DVR Menu bar > Information page to check your DVR Model. This firmware is for Model 4CH(M_VIII_HB) and 8CH(M_VIII_HB).

2. Please don’t try to downgrade your DVR to an older firmware version if your DVR is already [Version:8638000020220331] to avoid unknown failures in the DVR.

As always, feel free to email us at service@tigersecu.com with any questions. We’re here to help.

*Release – [Version: 8638000020220331]

• Upgrading Instruction-H.264 2MP Series 4CH(M_VIII_HB) and 8CH(M_VIII_HB)

Release notes:

This firmware will update your system to [Version: 8638000020220331] which has the following improvements:

1. Optimized system time zone settings

2. Supported playback timeline zoom function

3. Fixed some known issues

__________________________________

*Security note:

To ensure your ongoing privacy, we strongly recommend creating your own password from the all-access default password as soon as possible, if you have not already done so. Choose something that you’ll remember, but that other would be unlikely to guess.

Change your password at DVR Main menu > Configuration menu > User > admin: Edit > Password Setup.

As always, feel free to email us at service@tigersecu.com with any questions. We’re here to help.

H.264 HD 2MP 16CH(M_VII_HB) DVR Firmware(V20220331)

Important Tip:

1. Go to the DVR Menu bar > Information page to check your DVR Model. This firmware is for Model 16CH(M_VII_HB).

2. Please don’t try to downgrade your DVR to an older firmware version if your DVR is already [Version:8638000020220331] to avoid unknown failures in the DVR.

As always, feel free to email us at service@tigersecu.com with any questions. We’re here to help.

*Release – [Version: 8638000020220331]

• Upgrading Instruction-H.264 2MP Series 16CH(M_VII_HB).

Release notes:

This firmware will update your system to [Version: 8638000020220331] which has the following improvements:

1. Optimized system time zone settings

2. Supported playback timeline zoom function

3. Fixed some known issues

__________________________________

*Security note:

To ensure your ongoing privacy, we strongly recommend creating your own password from the all-access default password as soon as possible, if you have not already done so. Choose something that you’ll remember, but that other would be unlikely to guess.

Change your password at DVR Main menu > Configuration menu > User > admin: Edit > Password Setup.

As always, feel free to email us at service@tigersecu.com with any questions. We’re here to help.

<p>The post TIGERSECU NVR XVR Firmware Upgrading Instruction first appeared on NVR IPCAMERA SECURITY.</p>

Chapter 1 Startup

1.1 Activate Your Device

For the first-time access, you need to activate the video recorder by setting an admin password. No operation is allowed before activation. You can also activate the video recorder via web browser, SADP or client software.

Before You Start

Power on your device.

Steps

1. Select a language.
2. Click Next.
3. Input the same password in Password and Confirm Password.

/¡K Warning

Strong Password recommended-We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

1. Activate network camera(s) connected to the device.

• Check Use Device Password as Default to use the device password to activate the inactive network camera(s).
• Enter a password to activate network camera(s).

1. Optional: Set an email address for password resetting. When you forget your password, you can reset it by email.
2. Check Enable.
3. Enter an email address.
4. Click Activate.

User Name admin

Password

Weak

Confirm Password

Camera Activation Password 0 Use Device Password as Default

Email to Reset Password 0 Enable

Email Address

Hilook 4K NVR Device Complete Guide

Read More :

1. Hilook Hikvision Password Reset NVR/DVR/IPCAM NEW
2. Hilook Firmware Software Tools
3. How to Find The Encryption/Verification Code? Hilook Hikvision Annke

Figure 1-1 Activation

1.2 Login

• • 1. Set Unlock Pattern

Admin user can use the unlock pattern to login. You can configure the unlock pattern after the device is activated.

Steps

1. Use the mouse to draw a pattern among the 9 dots on the screen. Release the mouse when the pattern is done.

03 Note

• The pattern shall have 4 dots at least.
• Each dot can be connected for once only.

1. Draw the same pattern again to confirm it. When the two patterns match, the pattern is configured successfully.

Unlock Pattern

Set Unlock Pattern

Release your finger when done

Figure 1-2 Set

Set Unlock Pattern

Draw pattern again to confirm

• • 1. Log in via Unlock Pattern

Steps

1. Right click the mouse on live view interface.

Figure 1-3 Draw the Unlock Pattern

2. Draw the pre-defined pattern to unlock to enter the menu operation.

nXlNote

• If you have forgotten your pattern, you click Forgot My Pattern or Switch User to log in via password.
• If you have drawn the wrong pattern for more than 5 times, the system will switch to the normal login mode automatically.
  • 1. Log in via Password

If your video recorder has logged out, you must login before operating the menu and other functions.

Steps

1. Select User Name.

Welcome

Figure 1-4 Login Interface

1. Input password.
2. Click Login.

• When you forget the password of the admin, you can click Forgot Password to reset the password.
• If you enter the wrong password 7 times, the current user account will be locked for 60 seconds.

Chapter 2 Live View

• 1. GUI Introduction
• Click Target Detection at the upper-left corner, and select or to display the specified live target detection results. For result details, click View More.

HU Note

° Target Detection is only available for certain models.

° Target Detection is valid when HDD is installed.

° 0 is valid for motion detection, line crossing detection, intrusion detection, and facial detection.

• Click to start/stop auto-switch. The screen will automatically switch to the next one.
• Click to enter full screen mode.
• Double click a camera to view it in single-screen mode. Double click again to exit single-screen mode.
• Change a camera live view screen by dragging it from its screen to the desired screen.
• Scroll up/down to turn to previous/next screen.
• Position the cursor on a camera to show shortcut menu.

Figure 2-1 Shortcut Menu

Table 2-1 Shortcut Menu Description

• In the live view interface, there are icons at the upper-right corner of the screen for each

camera, showing the camera recording and alarm status.

Table 2-2 Live View Icon Description

• Right click your mouse to display the shortcut menu.

Menu

Ei Single Screen >

S Window Division >

< Previous Screen

> Next Screen

O Si art All! D-swHch

EJ Camera

® Playback

a FTZ Control

Figure 2-2 Right Click Shortcut Menu

• 1. PTZ Control
     1. Configure PTZ Parameter

You shall configure PTZ parameters before controlling a PTZ camera.

Steps

1. Preview a camera in live view and click 0 on shortcut menu.

2. Click PTZ Parameter Settings.

Figure 2-3 PTZ Settings

Figure 2-4 PTZ Parameter

1. Set the PTZ camera parameters.

C0Note

• All parameters should be the same as the PTZ camera.
• For the Coaxitron camera/dome connected, you can select the PTZ protocol to UTC (Coaxitron). Ensure the selected protocol is supported by the connected camera/dome.
• The AHD and HDCVI cameras support coaxitron control.
• Selecting Coaxitron protocol will make other parameters unavailable, including baud rate, data bit, stop bit, parity and flow control.

1. Click OK.
   • 1. PTZ Control Panel Introduction

Table 2-3 PTZ Panel Description

• • 1. Customize Preset

Set a preset location where the PTZ camera would point to when an event occurs.

Steps

1. Preview a camera in live view and click on shortcut menu.
2. Select a desired preset in preset list.
3. Use direction buttons to wheel the camera to required locations. Adjust zoom and focus as your desire.
4. Click 1* .

What to do next

Double click a preset in the preset list to call it.

• • 1. Customize Patrol

Patrol refers to a path consists of a series of presets with designated sequence. It provides dynamic live image for monitoring several presets.

Steps

1. Preview a camera in live view and click on shortcut menu.
2. Click Patrol.
3. Select a desired patrol.
4. Click Set.
5. Click + .
6. Configure key point parameters, such as the key point No., duration of staying for one key point and speed of patrol. The key point is corresponding to the preset. The preset number determines the order at which the PTZ will follow while cycling through the patrol. Duration refers to the time span to stay at the corresponding key point. Speed defines the speed at which the PTZ will move from one key point to the next.

Figure 2-5 Patrol Settings

1. Click Apply.

What to do next

Select a patrol and click Call to call it. The PTZ camera will move according the predefined patrol path.

Patroll ▼

Set Call

Figure 2-6 Call Preset

• • 1. Customize Pattern

A pattern records the movement path and dwell time in a certain position. When you call a pattern, the PTZ camera will move according to the recorded path.

Steps

1. Preview a camera in live view and click on shortcut menu.
2. Click Pattern.
3. Select a pattern.
4. Click Record.
5. Use direction buttons to wheel the camera to required locations. Adjust zoom and focus as your desire.
6. Click Stop Recording. The previous PTZ camera moving path is recorded as a pattern.

What to do next

Select a pattern and click Call to call it. The PTZ camera will move according the predefined

pattern.

Chapter 3 Playback

• 1. GUI Introduction

Go to Playback .

Figure 3-1 Playback

Table 3-1 Playback Interface Description

Figure 3-2 Timeline

• Position the cursor on the timeline, drag the timeline to position to a certain time.
• Period marked with blue bar contains video. Red bar indicates the video in the period is event video.
• Scroll up/down to zoom out/in timeline.
  1. Normal Playback

Play back normal videos.

Steps

1. Go to Playback .
2. Select a camera from the camera list.
3. Select a date on the calendar for playback.

C®Note

The blue triangle at the calendar date corner indicates there are available videos. For example, means video is available. 22 means no video.

1. Optional: Position the cursor on playback window to show control bar.

Figure 3-3 Control Bar

Table 3-2 Button Description

• 1. Smart Playback

The smart playback function provides an easy way to get through the less effective information. When you select the smart playback mode, the system will analyze the video containing the motion detection, line crossing detection, or intrusion detection information.

Before You Start

Configure motion detection, line crossing detection, and intrusion detection rules and detection areas.

Steps

1. Go to Playback .
2. Click Smart.
3. Select a camera.

Figure 3-4 Smart Playback Interface

4. Position the cursor on playback window to show control bar.

Figure 3-5 Control Bar

Table 3-3 Button Description

Normal Video

Set normal video playback speed. The option is only valid when Do not Play Normal Videos is unchecked.

Play Speed of Smart/Custom Video

Set playback speed of videos with smart information. The option is only valid when Do not

Play Normal Videos is enabled.

Play Strategy

Do not Play Normal Videos 0

Normal Video

—- _ ——— X 8

Play Speed of Smart/Custom Video

—————— X1

Cancel

Figure 3-6 Play Strategy

3.4 Back up Clip

You can clip videos during playback. Video clips can be exported to the backup device (USB flash drives, USB HDDs, USB writer, SATA writer, etc.).

Before You Start

Connect a backup device to your video recorder.

Steps

1. Start playback. Refer to Normal Playback for details.
2. Click .
3. Clip videos.

• Click Q, set start and end time, click OK.
• Set a time segment on time bar for clipping.

Figure 3-7 Time Segment

1. Click [7] .
2. Click Export to export the clip to backup device.
3. Search File

Steps

1. Go to Search .
2. Set search conditions.
3. Click Search.

• Click to play the video.
• Click to lock the file. Locked file will not be overwritten.
• Select file(s), and click Export to export file(s) to backup device.

System Date

System Time

Resolution

Enable Wizard

Enable Password

Enable NTP

Interval (min)

NTP Server

NTP Port

1. Configuration (Easy Mode)

Easy mode contains basic configurations. Go to Configuration , and click Easy Mode.

• 1. System Configuration
     1. General

You can configure the output resolution, system time, mouse pointer speed, etc.

Steps

1. Go to Configuration ^ System ^ General .

02-09-2019

19:35:38 ©

1024‘768i60HZ

□

0

□

60

time.windows com

123

Figure 5-1 General Settings

1. Configure the parameters as your desire.

Enable Wizard

The wizard will pop up after the device starts up.

Enable Password

You need to enter password for authentication if the device automatically logged out.

Enable NTP

Network time protocol (NTP) is a networking protocol for time synchronization. The device can connect to NTP (network time protocol) server to sync time.

Interval (min)

Time interval between two time synchronization with NTP server.

NTP Server

IP address of the NTP server.

NTP Port

Port of the NTP server.

1. Click Apply.
   • 1. User

Add User

There is a default account: Administrator. The administrator user name is admin. Administrator has the permission to add, delete, and edit user. Guest user only has live view, playback, and log search permission.

Steps

1. Go to Configuration ^ User .
2. Click Add and confirm your admin password.

Figure 5-2 Add User

1. Enter user name.
2. Enter the same password in Password and Confirm.

/ * \ Warning

We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

1. Click OK.

– Click / to edit user.

Set Password Resetting Email

When you forgot your login pattern and password, the device will send an email contains verification code to your email for password resetting.

Steps

1. Go to Configuration ^ User .
2. Click Password Resetting Email.
3. Enter admin password for authorization.
4. Enter an email address.
5. Click OK.

Reset Password

You can reset your password when you forgot your login pattern and password.

Steps

1. Click Forgot Password at the password login interface.
2. Click Next if you agree the Privacy Policy, you can scan the QR code to read it.
3. Follow the wizard to reset password.

5.1.3 Exception

You can receive exception events hint in alarm center, and set exception linkage actions.

Steps

1. Go to Configuration ^ System ^ Exception .
2. Optional: Configure event hint. When the set events occur, you will receive hints in alarm center.
3. Check Event Hint.
4. Click at the upper-right corner of local menu to enter alarm center.
5. Select an event type.
6. Click Set to select events to hint.
7. Set Exception Type
8. Select Normal Linkage and Trigger Alarm Output type for exception linkage actions.

□ Audible Warning □ 10.96.15.145:8000->1

□ 10.96.15.1 45:8000->2

□ Notify Surveillance Center

□ Send Email

Figure 5-3 Exceptions

1. Click Apply.

5.2 Network Configuration

• • 1. General

You shall properly configure the network settings before operating the device over network.

Steps

1. Go to Configuration ^ Network ^ General .

DHCP

IPv4 Address

IPv4 Subnet Mask

IPv4 Default Gateway

Obtain DNS Automatically 0

Preferred DNS Server

Alternate DNS Server

Figure 5-4 Network

1. Set network parameters.

DHCP

If the DHCP server is available, you can check Enable DHCP to automatically obtain an IP address and other network settings from that server.

Obtain DNS Automatically

If DHCP is checked. You can check Obtain DNS Automatically to automatically obtain

Preferred DNS Server and Alternate DNS Server.

1. Click Apply.
   • 1. HiLookVision

HiLookVision provides mobile phone application and platform service to access and manage your connected devices, which enables you to get a convenient remote access to the video security system.

Steps

1. Go to Configuration ^ Network ^ Platform Access .
2. Select Access Type as HiLookVision.
3. Check Enable. The service terms will pop up.
4. Scan the QR code to read the service terms and privacy statement.
5. Check I have read and agree to Service Terms and Privacy Statement. if you agree the service terms and privacy statement..
6. Click OK.
7. Optional: Check Stream Encryption. It requires to enter verification code in remote access and live view after this function is enabled.
8. Optional: Check Custom, and edit Server Address.
9. Enter a code in Verification Code. You can click Refresh to randomly generate a verification code.
10. Bind your device with a HiLookVision account.
11. Use a smart phone to scan the QR code, and download HiLookVision app. You can also download it from https://appstore.hikvision.com, or the QR code below. Refer to HiLookVision Mobile Client User Manual for details.

Figure 5-5 Download HiLookVision

2) Use HiLookVision to scan the device QR, and bind the device.

Hl® Note

If the device is already bound with an account, you should unbind with the current account.

1. Click Apply.

What to do next

You can access your video recorder via HiLookVision.

• • 1. Email

Set an email account to receive event notification.

Before You Start

• Ensure your video recorder is in a local area network with an SMTP mail server.
• Configure your network parameters. Refer to General for details.

Steps

1. Go to Configuration ^ Network ^ Email .

Server Authentication

User Name

Password

SMTP Server

SMTP Port

SSUTLS

Attached Picture

Sender

Sender’s Address

Select Receivers

Receiver

Receiver’s Address

Figure 5-6 Email

1. Set email parameters

Server Authentication

(Optional), check it to enable the server authentication feature.

User Name

The user account of email sender for SMTP server authentication.

Password

The password of email sender for SMTP server authentication.

SSL/TLS

(Optional), check it to enable SSL/TLS if it required by the SMTP server.

Sender

The sender name.

Sender’s Address

The sender’s email address.

Select Receiver

Select a receiver. Up to 3 receivers are available.

Receiver

The receiver name.

Receiver’s Address

The receiver’s email address.

djNote

• For network cameras, the event images are directly sent as the email attachment. One network camera only sends one picture.
• For analog cameras, 3 attached pictures will be sent for one analog camera when an event occurs.

1. Click Apply.

5.3 Camera Management

• • 1. Network Camera

Add Network Camera by Device Password

Add network cameras which the password is the same as your video recorder.

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct. Refer to General for details.
• Ensure the network camera password is the same as your video recorder.

Steps

1. Go to Configuration ^ Camera ^ IP Camera . The online cameras on the same network segment with your video recorder are displayed in the camera list.

+ Ql UI 0 9 Search!-

□ No. I IP Address I Edit I Add/Delete I Security I Status I Camera Name

… 10.6.114.36 ~ + ©Active A

Figure 5-7 IP Camera Management Interface

1. Click + to add the camera.

Add Network Camera Manually

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.
• Ensure the network camera is activated.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click + .
3. Set network camera parameters, including IP address, protocol, management port, etc. You can check Use IPC Active Password to use the device password to add network camera(s).
4. Optional: Click Add More to add another network camera.
5. Click OK.

Figure 5-8 Add Network Camera

Edit Connected Network Camera

You can edit the IP address, protocol and other parameters of the added network cameras.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click / to edit the selected camera.

Channel Port

If the connected device is an encoding device with multiple channels, you can select the channel port No. to choose a connecting channel.

1. Click OK.

Sort Channel Order

Channel layout windows are ordered by channel number. You can change the camera linked channel number by dragging windows.

Steps

1. Go to Configuration ^ Camera ^ Camera .
2. Click Sort Channel.
3. Drag a channel window to the channel number as your desire.
4. Click Apply.

C®Note

After sorting channels, the device will reconnect to network cameras.

Configure Remote Settings

For the camera parameters that were only configurable via web browser, remote settings function provides an operation interface to configure remote camera parameters.

Before You Start

Ensure your camera is properly connected.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click Remote Settings
3. After the device resource is initialized, select a camera.
4. Set camera parameters.

Upgrade Network Camera

The Network camera can be remotely upgraded through the device.

Before You Start

• Ensure you have inserted the USB flash drive to the device, and it contains the network camera upgrade firmware.
• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click O .
3. Click Yes to confirm.
4. Select the camera upgrade firmware from your storage device.
5. Click Upgrade to start upgrading. The camera will restarted automatically after upgrade completed.

Configure Advanced Camera Parameters

You can configure advanced camera parameters like camera IP address, camera password, etc.

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click ® .
3. Set camera parameters like IP address, camera password, etc.
4. Click Apply.

5.3.2 OSD Settings

Configure OSD (On-Screen Display) settings for the camera, including date format, camera name, etc.

Steps

1. Go to Configuration ^ Camera ^ OSD .
2. Select a camera.

Figure 5-9 OSD

3. Drag the text frames on the preview window to adjust the OSD position.

4. Click Apply.

5.3.3 Event

Motion Detection

Motion detection enables the video recorder to detect the moving objects in the monitored area and trigger alarms.

Steps

1. Go to Configuration ^ Camera ^ Motion Detection .
2. Select a camera.
3. Check Enable.
4. Set the motion detection area.

• Click Draw Area or Clear to draw or clear areas. The first area is set as full screen by default.
• Click Full Screen to set the motion detection area as full screen. You can drag on the preview window to draw motion detection areas.

C® Note

The operation may differ according to different models.

1. Adjust Sensitivity. Sensitivity allows you to calibrate how readily movement triggers the alarm. A higher value results in the more readily to triggers motion detection.
2. Set analysis mode as AI or PIR.

AI

The motion detection event will be analyzed by your device.

PIR

The motion detection event will be analyzed by certain analog PIR cameras.

1. Optional: Set Target Detection as Human or Vehicle to discard alarms which are not triggered by human or vehicle.

US Note

This function is only available for certain models.

1. Set the arming schedule. Refer to Configure Arming Schedule for details.
2. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
3. Click Apply.

Configure Arming Schedule

Steps

1. Select Arming Schedule.
2. Choose one day of a week and set the time segment. Up to eight time periods can be set within each day.

djNote

Time periods shall not be repeated or overlapped.

Figure 5-10 Set Arming Schedule

1. Click Apply.

Configure Alarm Linkage Action

Alarm linkage actions will be activated when an alarm or exception occurs.

Steps

1. Click Linkage Action.

Figure 5-11 Linkage Actions

2. Set normal linkage actions, trigger alarm output, trigger recording channel, etc.

Full Screen Monitoring

The local monitor will display the alarming channel image in full screen when an alarm is triggered. It requires to select the alarming channel(s) in Trigger Channel.

Audible Warning

It will trigger an audible beep when an alarm is triggered.

Notify Surveillance Center

The device will send an exception or alarm signal to the remote client software when an alarm is triggered.

Send Email

It will send an email with alarm information when an alarm is triggered.

PTZ Linkage

It will trigger PTZ actions (e.g., call preset/patrol/pattern) when smart events occur.

3. Click Apply.

5.4 Device Management

• • 1. Switch

Add and manage switches.

Quick Add Switch

Quick add switch(es) in the same network segment with the video recorder. If the switch is not activated, it will be added with the channel default password.

Steps

1. Go to Configuration ^ Device Management ^ Switch.
2. In the Online Device List, check the switch(es) to be added and click Add to add switch(es) in the same network segment with the video recorder using the channel default password.

Add Switch Manually

Steps

1. Go to Configuration ^ Device Management ^ Switch .
2. In the Online Device List, click Add and set the parameters of the channel.

Table 5-1 Channel Parameter Description

3. Click Add and Continue and repeat operation until all device have been added.

4. Click Add.

5.4.2 Non-Video Event

Configure non-video event.

Steps

1. Go to Configuration ^ Device Management ^ Non-Video Event.
2. Select the device.
3. Select the Alarm Content.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply_o

5.5 Recording Management

• • 1. Storage Device

Initialize HDD

A newly installed hard disk drive (HDD) must be initialized before it can be used to save videos and information.

Before You Start

Install at least an HDD to your video recorder. For detailed steps, refer to Quick Start Guide.

Steps

1. Go to Configuration ^ Record ^ Storage .
2. Select an HDD.
3. Click Init.

Repair Database

Repair an HDD that with error in database. Please operate it with the help of professional technical support.

Secure Erase

Secure erase will delete videos in the selected disk(s).

Add Network Disk

You can add the allocated NAS or IP SAN disk to the video recorder, and use it as a network HDD.

Steps

1. Go to Configuration ^ Record ^ Storage .
2. Click Add.
3. Select NetHDD.
4. Set Type as NAS or IPSAN.
5. Enter NetHDD IP address.
6. Click Search to search the available disks.

Figure 5-12 Add NetHDD

7. Select NAS disk from the list, or manually enter the directory in NetHDD Directory.

8. Click OK. The added NetHDD will be displayed in the storage device list.

5.5.2 Configure Recording Schedule

Video recorder will automatically start/stop recording according to the configured schedule.

Configure Continuous Recording

Steps

1. Go to Configuration ^ Record ^ Parameter .
2. Set the continuous main stream/sub-stream recording parameters for the camera. Refer to Configure Recording Parameter for details.
3. Go to Configuration ^ Record ^ Schedule .
4. Select recording type as Continuous. Refer to Edit Schedule for details.

Configure Event Recording

You can configure the recording triggered by the motion detection, line crossing detection, and intrusion detection.

Steps

1. Go to Configuration ^ Event ^ Smart Event .
2. Configure the event detection and select the channels to trigger the recording when an event occurs.
3. Go to Configuration ^ Record ^ Parameter .
4. Set the continuous main stream/sub-stream recording parameters for the camera. Refer to Configure Recording Parameter for details.
5. Go to Configuration ^ Record ^ Schedule .
6. Select recording type as Event. Refer to Edit Schedule for details.

Edit Schedule

Steps

1. Go to Configuration ^ Record ^ Schedule .

Figure 5-13 Recording Schedule

Continuous

Continuous recording.

Event

Recording triggered by all event triggered alarm.

1. Select a camera in CameraNo.
2. Check Enable.
3. Configure the recording schedule.

Edit a. Click Edit.

Schedule b. Select a day to configure in Weekday.

1. To set an all-day recording schedule, check All Day and select schedule type.
2. To set other schedules, uncheck All Day, and set Start/End Time and schedule type.

Note

Up to 8 periods can be configured for each day. And the time periods cannot be overlapped with each other.

1. Click OK to save the settings and go back to upper level menu.

Figure 5-14 Edit Schedule

1. Click to select schedule type as Continuous or Event.

Draw

Schedule

5. Click Apply.

1. On the table, drag the mouse on the desired period to draw a colored bar.

5.5.3 Configure Recording Parameter

Steps

1. Go to Configuration ^ Record ^ Parameter .
2. Configure recording parameters.

Main Stream

Main stream refers to the primary stream that affects data recorded to the hard disk drive and will directly determine your video quality and image size. Comparing with the sub­stream, the main stream provides a higher quality video with higher resolution and frame rate.

Sub-Stream

Sub-stream is a second codec that runs alongside the mainstream. It allows you to reduce the outgoing internet bandwidth without sacrificing your direct recording quality. Sub-stream is often exclusively used by smartphone applications to view live video. Users with limited internet speeds may benefit most from this setting.

Frame Rate

Frame rate refers to how many frames are captured each second. A higher frame rate is advantageous when there is movement in the video stream, as it maintains image quality throughout.

Resolution

Image resolution is a measure of how much detail a digital image can hold: the greater the resolution, the greater the level of detail. Resolution can be specified as the number of pixel­columns (width) by the number of pixel-rows (height), e.g.,1024×768.

Bitrate

The bit rate (in Kbit/s or Mbit/s) is often referred to as speed, but actually defines the number of bits/time unit and not distance/time unit.

C® Note

Higher resolution, frame rate, and bitrate provide you better video quality, but it also requires more internet bandwidth and uses more storage space on the hard disk drive.

1. Click Apply.

Chapter 6 Configuration (Expert Mode)

Go to Configuration , and click Expert Mode at the lower-left corner.

• 1. System Configuration
     1. General

Configure Basic Settings

You can configure the language, system time, output resolution, mouse pointer speed, lock screen password, etc.

Go to Configuration ^ System ^ General ^ Basic Settings , configure the parameters as your desire, and click Apply.

Language

The default language is English.

VGA/HDMI Resolution

Select the output resolution, which must be the same with the resolution of the VGA/HDMI display.

Lock Screen Password

You need to enter password for authentication if the screen is locked.

Mouse Pointer Speed

Set the speed of mouse pointer. 4 levels are configurable.

Wizard

The wizard will pop up after the device starts up.

Enhanced Decoding Mode

Disabling enhanced decoding mode will reduce the local decoding capability by half and restart the device.

Configure DST Settings

DST (Daylight Saving Time) refers to the period of the year when clocks are moved one period ahead. In some areas worldwide, this has the effect of creating more sunlit hours in the evening during months when the weather is the warmest.

Go to Configuration ^ System ^ General ^ DST Settings , configure the parameters as your desire, and click Apply.

Configure More Settings

You can configure your device name, lock screen time, output mode, etc.

Go to Configuration ^ System ^ General ^ More Settings , configure the parameters as your desire, and click Apply.

Device Name

Edit the video recorder name.

Device No.

The number is required in the connection with remote control, network keyboard, etc. Edit the serial number of video recorder. The device number ranges from 1 to 255, and the default value is 255.

Lock Screen

Set timeout time for lock screen.

Menu Output Mode

Choose output to display local menu.

Figure 6-1 More Settings

• • 1. Live View

Configure General Parameters

You can configure the output interface, mute or turning on the audio, event output interface, etc.

Steps

1. Go to Configuration ^ System ^ Live View ^ General .

Enable Audio Output

Volume

Figure 6-2 Live View-General

1. Configure the Live View parameters.

Live View Mode

Select the live view window division.

Dwell Time

The time to dwell in a camera before switching to next camera when auto-switch in live view is enabled.

Event Output

Select the output to show event video.

Full Screen Monitoring Dwell Time

Set the time to show alarm event image.

Enable Audio Output

Turn on/off audio output for the selected video output.

Volume

Adjust the live view, playback, and two-way audio volume for the selected video output interface.

1. Click Apply.

Configure Live View Layout

Steps

1. Go to Configuration ^ System ^ Live View ^ View .
2. Select Video Output Interface to configure.
3. Click to select a window and click a camera No. in the camera list you would like to display. + means no camera is displayed on the window.
4. Optional: Click Q / f? to start/stop live view of all the cameras in order.
5. Click Apply.

Configure Channel-Zero Encoding

Enable the channel-zero encoding when you need to get a remote view of many channels in real time from a web browser or CMS (Client Management System) software, in order to decrease the bandwidth requirement without affecting the image quality.

Steps 1. Go 2. Set 3. Go

to Configuration ^ System ^ Live View ^ General . Video Output Interface as Channel-Zero.

to Configuration ^ System ^ Live View ^ Channel-Zero .

Enable Channel-Zero Encoding

Frame Rate

Max. Bitrate Mode

Max. Bitrate(Kbps)

Figure 6-3 Channel-Zero

1. Check Enable Channel-Zero Encoding.
2. Configure Frame Rate, Max. Bitrate Mode, and Max. Bitrate. The higher frame rate and bitrate settings result in higher bandwidth requirement.
3. Click Apply.

6.1.3 User

Refer to User for details.

6.2 Network Configuration

• • 1. TCP/IP

TCP/IP must be properly configured before you operate video recorder over network.

Steps

1. Go to Configuration ^ Network ^ General ^ TCP/IP .
2. Configure network parameters.

Working Mode

Multi-address Mode

The parameters of the two NIC cards can be configured independently. You can select LAN1 or LAN2 in the NIC type field for parameter settings. You can select one NIC card as default route. And then the system is connecting with the extranet and the data will be forwarded through the default route.

Net-fault Tolerance Mode

The two NIC cards use the same IP address, and you can select the Main NIC to LAN1 or LAN2. By this way, in case of one NIC card failure, the video recorder will automatically enable the other standby NIC card so as to ensure the normal running of the whole system.

Load Balance Mode

By using the same IP address and two NIC cards share the load of the total bandwidth, which enables the system to provide two Gigabit network capacity.

C® Note

Working mode is only available for certain models.

NIC Type

Select NIC type as your desire. If your device supports Wi-Fi dongle function, the NIC of Wi-Fi dongle would be selectable after a suitable Wi-Fi dongle is installed.

DHCP

If the DHCP server is available, you can check Enable DHCP to automatically obtain an IP address and other network settings from that server.

MTU

The maximum transmission unit (MTU) is the size of the largest network layer protocol data unit that can be communicated in a single network transaction.

Default Route

Select a route as your desire. If your device supports Wi-Fi dongle function, the route of Wi-Fi dongle would be selectable after a suitable Wi-Fi dongle is installed.

Auto Obtain DNS

If DHCP is checked. You can check Obtain DNS Automatically to obtain Preferred DNS Server and Alternate DNS Server.

1. Click Apply.
   • 1. DDNS

Dynamic domain name server (DDNS) maps dynamic user IP addresses to a fixed domain name server.

Before You Start

Register DynDNS, PeanutHull and NO-IP services with your ISP.

Steps

1. Go to Configuration ^ Network ^ General ^ DDNS .

Enable 0

DDNS Type DynDNS ▼

Server Address

Device Domain Name

User Name

Password

Status DDNS is disabled

Figure 6-4 DDNS

1. Check Enable.
2. Select a DDNS type.
3. Enter parameters including service address, domain name, etc.
4. Click Apply.

What to do next

You can view DDNS status in Status.

• • 1. NAT

Two ways are provided for port mapping to realize the remote access via the cross-segment network, UPnP™ and manual mapping.

Before You Start

Enable the UPnP™ function of your router if UPnP™ is required. When the device network working mode is multi-address, the default device route should be on the same network segment as the LAN IP address of the router.

Steps

1. Configuration ^ Network ^ General ^ NAT .
2. Check Enable.
3. Select Mapping Type as Manual or Auto

Auto The port mapping items are read-only, and the external ports are set by the router automatically. You can click Refresh to get the latest status of the port mapping.

Manual Select an external port type. Click / to edit External Port. You can use the default external port No., or change it according to actual requirements. External Port indicates the port No. for port mapping in the router.

The value of the RTSP port No. should be 554 or between 1024 and 65535, while the value of the other ports should be between 1 and 65535 and the value must be different from each other. If multiple devices are configured for the UPnP™ settings under the same router, the value of the port No. for each device should be unique.

1. Set the virtual server of your router, including internal source port, external source port, etc. The virtual server parameters shall be corresponding with your device port.
   • 1. Ports (More Settings)

Set different port types to enable relevant functions as your desire.

Go to Configuration ^ Network ^ General ^ More Settings .

Alarm Host IP/Port

The device will send the alarm event or exception message to the alarm host when an alarm is triggered. The remote alarm host must have the client management system (CMS) software installed.

Alarm Host IP refers to the IP address of the remote PC on which the CMS software (e.g., iVMS-4200) is installed, and the Alarm Host Port (7200 by default) must be the same as the alarm monitoring port configured in the software.

Server Port

For remote client software access. Ranges from 2000 to 65535. The default value is 8000.

HTTP Port

For remote web browser access. The default value is 80.

Multicast IP

Multicast can be configured to enable live view for cameras that exceed the maximum number allowed through network. A multicast IP address covers Class-D IP ranging from 224.0.0.0 to 239.255.255.255 and it is recommended to use the IP address ranging from 239.252.0.0 to 239.255.255.255.

When adding a device to the CMS software, the multicast address must be the same as that of the device.

RTSP Port

RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and communications systems to control streaming media servers. The port is 554 by default.

Output Bandwidth Limit

You can check the checkbox to enable output bandwidth limit.

Output Bandwidth

After enable the output bandwidth limit, input the output bandwidth.

CUl Note

• The output bandwidth limit is used for the remote live view and playback.
• The default output bandwidth is the maximum limit.

Figure 6-5 Port Settings

6.2.5 Upload Logs to the Server

You can upload system logs to the server for backup.

Steps

1. Go to Configuration ^ Network ^ General ^ Log Server Settings .

Enable

Upload Time Interval (Fi) 1

Server IP Adtfress

Port 514

Apply

Figure 6-6 Log Server Settings

1. Turn on Enable
2. Set Upload Time Interval, Server IP Address, and Port.
3. Optional: Click Test to test if parameters are valid.
4. Click Apply.
   • 1. HiLookVision

Go to Configuration ^ Network ^ Platform Access . Refer to HiLookVision for details.

• • 1. Email

Go to Configuration ^ Network ^ Email . Refer to Email for details.

6.3 Camera Management

• • 1. Network Camera

Add Automatically Searched Online Network Camera

Add the network cameras to your video recorder.

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.
• Ensure the network camera password is the same as your video recorder.

Steps

1. Go to Configuration ^ Camera ^ Camera ^ IP Camera .
2. Click Online Device. The online cameras on the same network segment will be displayed in the list.

+ Qi ICT O 9 Searchl-

□ No. I IP Address I Edit I Add/Delete I Security I Status I Camera Name

… 10.6.114.36 ~ + ©Active A

Figure 6-7 Online Device

1. Select a network camera, and click Add to add it.

Add Network Camera Manually

Add the network cameras to your video recorder.

Before You Start

• Ensure your network camera should be in the same network segment with your video recorder.
• Ensure the network connection is valid and correct.
• Activate the network camera to add.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click + .

Figure 6-8 Add IP Camera

3. Enter information of the network camera to add.

Use Channel Default Password

If it is checked, the video recorder will add the camera by the set channel default password.

4. Click Add.

Add Network Camera on Different Network Segment

If your network camera is on a different network segment, the device can search its IP address within a range of IP addresses, and add it.

Before You Start

• Ensure the network connection is valid and correct.
• Ensure the network camera password is the same as your video recorder.

Steps

1. Go to Configuration ^ Camera ^ Camera ^ IP Channel .
2. Click Advanced Search.
3. Enter Network Segment.

first three octets the camera IP address.

O If your network camera is not on the same network segment with the NVR and s… ,

□ Network Segment 192 . 168 . 0 . 0

□ Network Segment 192. 168.1 . ~

| Cancel

Figure 6-9 Enter Network Segment

1. Click Add.

Add Network Camera Through Plug-and-Play

If an inactive network camera or third party ONVIF camera is connected to your network, the video recorder may automatically detect and add the camera, or notify you to manually add it.

Steps

1. Go to Configuration ^ Camera ^ Camera ^ IP Channel .
2. Click More.
3. Select Plug-and-Play.
4. Optional: Enable Auto Add Network Camera. The video recorder would automatically detect and add the inactive network camera or third party ONVIF camera.

Plug-and-Play x

Auto Add Network Camera «

OK

Figure 6-10 Auto Add Network Camera

‘Note

If you turn off Auto Add Network Camera, when an inactive network camera or third party ONVIF camera is connected to your network, the video recorder would automatically detect it and notify you to add it.

Edit Connected Network Camera

You can edit the IP address, protocol and other parameters of the added network cameras.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click / of an added network camera.

Channel Port

If the connected device is an encoding device with multiple channels, you can choose the channel to connect by selecting the channel port No. in the drop-down list.

1. Click OK.

Example

Enter an example that illustrates the current task (optional).

What to do next

Enter the tasks the user should do after finishing this task (optional).

Upgrade Network Camera

The Network camera can be remotely upgraded through the device.

Before You Start

• Ensure you have inserted the USB flash drive to the device, and it contains the network camera upgrade firmware.
• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.

Steps

1. Go to Configuration ^ Camera ^ Camera .
2. Click .
3. Click Yes to confirm.
4. Select the camera upgrade firmware from your storage device.
5. Click Upgrade to start upgrading. The camera will restarted automatically after upgrade completed.

Add Network Camera Through PoE

The PoE interfaces enable the device to transfer electrical power and data to connected PoE cameras. And the PoE interface supports the Plug-and-Play function. Connectable PoE camera number varies with device models. If you disable a PoE interface, you can also use it to connect to an online network camera.

Add PoE Camera

Steps

1. Go to Configuration ^ Camera ^ Camera ^ PoE Settings .
2. Enable or disable long network cable mode by selecting Long Distance or Short Distance.

Long Distance

Long-distance (100 to 300 meters) network transmissions via PoE interface.

Short Distance

Short-distance (< 100 meters) network transmission via PoE interface.

C® Note

• The PoE ports are enabled with the short distance mode by default.
• The bandwidth of IP camera connected to the PoE via long network cable (100 to 300 meters) cannot exceed 6 Mbps.
• The allowed max. long network cable may be less than 300 meters depending on different IP camera models and cable materials.
• When the transmission distance reaches 100 to 250 meters, you must use the CAT5e or CAT6 network cable to connect with the PoE interface.
• When the transmission distance reaches 250 to 300 meters, you must use the CAT6 network cable to connect with the PoE interface.

Figure 6-11 Add PoE Camera

1. Click Apply.
2. Connect PoE cameras to your device PoE interfaces with network cables.

What to do next

The connected PoE camera will be displayed in Configuration ^ Camera ^ Camera ^ IP Channel .

You can click its status to view live image.

Add Non-PoE Network Camera

You can use the PoE channel resource to connect a non-PoE network camera.

Steps

1. Go to Configuration ^ Camera ^ Camera ^ IP Channel .
2. Click jo of a channel with no linked network camera.
3. Select Adding Method as Manual.

Plug-and-Play

The camera is physically connected to the PoE interface. You can click ® in the added device list to edit its parameters.

Manual

Add IP camera without physical connection via network cable.

1. Set other parameters, such as user name, password, and IP address.

Configure Advanced Camera Parameters

You can configure advanced camera parameters like camera IP address, camera password, etc.

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.

Steps

1. Go to Configuration ^ Camera ^ Camera .
2. Click ® .
3. Set camera parameters like IP address, camera password, etc.
4. Click Apply.

Configure Channel Type

You can disable a PoE channel to additionally increase a normal IP channel resource.

Go to Configuration ^ Camera ^ Camera ^ PoE Binding Configuration , and set the PoE channel as your desire.

Figure 6-12 PoE Binding Configuration

Sort Channel Order

Go to Configuration ^ Camera ^ Camera . Refer to Sort Channel Order for details.

Configure Remote Settings

Go to Configuration ^ Camera ^ Camera . Refer to Configure Remote Settings for details.

Import/Export IP Camera Configuration File

The information of added network camera can be generated into an excel file and exported to the local device for backup, including the IP address, manage port, password of admin, etc. And the exported file can be edited on your computer, like adding or deleting the content, and copy the setting to other devices by importing the excel file to it.

Before You Start

Connect a backup device like USB flash drive to your video recorder.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click El
3. Click Export to export configuration files to the connected backup device.
4. To import a configuration file, select the file from the selected backup device and click Import. After the importing process is completed, you must reboot the video recorder.

Advanced Settings

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click O .
3. Configure the parameters as your desire.

H.265 Auto Switch Configuration

If you enable the option, video recorder will automatically switch to H.265 stream for the network camera (which supports H.265 video format) for the initial access.

Upgrade

Upgrade the added network cameras.

Channel Default Password Management

Change the default password of activating and adding network camera.

• • 1. Display Settings

Configure the OSD (On-Screen Display), image settings, exposure settings, day/night switch settings, etc.

Steps

1. Go to Configuration ^ Camera ^ Display .
2. Select Camera.
3. Configure parameters as your desire.

OSD Settings

Configure the OSD (On-screen Display) settings for the camera, including date/time, camera name, etc.

Image Settings

Customize the image parameters including the brightness, contrast, and saturation for the live view and recording effect.

Exposure

Set the camera exposure time (1/10000 to 1 sec). A larger exposure value results in a brighter image.

Day/Night Switch

The camera can be set to day, night, or auto switch mode according to the surrounding illumination conditions.

Backlight

Set the camera’s wide dynamic range (0 to 100). When the surrounding illumination and the object have large differences in brightness, you should set the WDR value.

Image Enhancement

For optimized image contrast enhancement.

OSD Settings

Image Settings

Exposure

Day/Night Switch

Backlight

Image Enhancement

Camera Parameters Settings

Camera

Camera Name

Camera 01

Figure 6-13 OSD

4. Drag the text frames on the preview window to adjust the OSD position.

5. Click Apply.

• • 1. Privacy Mask

You are allowed to configure the privacy mask areas that cannot be viewed or recorded.

Steps

1. Go to Configuration ^ Camera ^ Privacy Mask .
2. Select Camera.
3. Check Enable.

Clear Area 1

□ Clear Area 2

□ Clear Area 3

□ Clear Area 4

Clear All

Camera

Enable

Figure 6-14 Privacy Mask

4. Drag to draw an area on the window. The frames of the areas will be marked with different colors.

OZlNote

Up to 4 privacy mask areas can be configured. The size of each area can be adjusted.

5. Click Apply.

6.4 Device Management

• • 1. Switch

Add and manage switches.

Quick Add Switch

Quick add switch(es) in the same network segment with the video recorder. If the switch is not activated, it will be added with the channel default password.

Steps

1. Go to Configuration ^ Device Management ^ Switch.
2. In the Online Device List, check the switch(es) to be added and click Add to add switch(es) in the same network segment with the video recorder using the channel default password.

Add Switch Manually

Steps

1. Go to Configuration ^ Device Management ^ Switch .
2. In the Online Device List, click Add and set the parameters of the channel.

Table 6-1 Channel Parameter Description

3. Click Add and Continue and repeat operation until all device have been added.

4. Click Add.

6.5 Event Configuration

• • 1. Normal Event

Motion Detection

Motion detection enables the video recorder to detect the moving objects in the monitored area and trigger alarms.

Steps

1. Go to Configuration ^ Camera ^ Motion Detection .
2. Select a camera.
3. Check Enable.
4. Set the motion detection area.

• Click Draw Area or Clear to draw or clear areas. The first area is set as full screen by default.
• Click Full Screen to set the motion detection area as full screen. You can drag on the preview window to draw motion detection areas.

1. Adjust Sensitivity. Sensitivity allows you to calibrate how readily movement triggers the alarm. A higher value results in the more readily to triggers motion detection.
2. Set analysis mode as AI or PIR.

AI

The motion detection event will be analyzed by your device.

PIR

The motion detection event will be analyzed by certain analog PIR cameras.

1. Optional: Set Target Detection as Human or Vehicle to discard alarms which are not triggered by human or vehicle.
2. Set the arming schedule. Refer to Configure Arming Schedule for details.
3. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
4. Click Apply.

Video Tampering

Trigger alarm when the lens is covered and take alarm response actions.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Video Tampering .

Figure 6-15 Video Tampering

1. Set Camera.
2. Turn on Enable.
3. Adjust Sensitivity as your desire. The higher the value is, the more easily the video tampering can be triggered.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply.

Video Loss

Detect video loss of a camera and take alarm response actions.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Video Loss .
2. Set Camera.
3. Turn on Enable.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply.

Alarm Input

Set linkage actions for an external sensor alarm.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Alarm Input .

Figure 6-16 Alarm Input

Note

Local alarm input: Local alarm input is triggered by the external device that connected to the video recorder’s terminal block.

1. Click jo of a desired alarm input.

Figure 6-17 Edit Alarm Input

1. Customize Alarm Name.
2. Set alarm type as N.O (normally open) or N.C (normally closed).
3. Set Settings as Input to enable the function.

C®Note

If you set Settings as Nonuse, the alarm input will be disabled. If you set Settings as One-Key Disarming, the selected linkage method(s) of the alarm input will be disabled.

1. Set the arming schedule. Refer to Configure Arming Schedule for details.
2. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
3. Click Apply.

Alarm Output

Trigger an alarm output when an alarm is triggered.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Alarm Output .

Figure 6-18 Alarm Output

1. Click <o of a desired alarm output.
2. Customize Alarm Name.
3. Select Dwell Time.

Figure 6-19 Edit Alarm Output

1. Set Settings as Input to enable the function.
2. Set the arming schedule. Refer to Configure Arming Schedule for details.
3. Click Apply.

Flashing Light Alarm Output

When light and audio alarm camera is connected, you can set the flashing time, flashing frequency, and arming schedule of the flashing light alarm.

Before You Start

Light and audio alarm camera is connected.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Flashing Light Alarm Output.
2. Click E for any row.
3. Set the Flashing Time and Flashing Frequency.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. ClickSave.

Audio Alarm Output

When light and audio alarm camera is connected, you can set the parameters and arming schedule of the audio alarm.

Before You Start

Light and audio alarm camera is connected.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Flashing Light Alarm Output.
2. Click S for any row.
3. Select the Audio Type as Alarm Sound, Prompt Sound, or Custom Audio.

CHjNote

• When you select the Alarm Sound, you also need to select the alarm sound type.
• When you select the Alarm Sound, you also need to upload the custom audio, enter the audio name and select the uploaded audio in the drop-down box of Custom Audio.

1. Set the Alarm Times and Sound Volume.
2. Set the arming schedule. Refer to Configure Arming Schedule for details.
3. ClickSave.

Exception

Exception events can be configured to take the event hint in the live view window and trigger alarm outputs and linkage actions.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Exception .
2. Configure event hint. When the set events occur, you will receive hints in alarm center.
3. Enable Event Hint.
4. Select events to hint. Choose from:

• Click @ of Event Hint Configuration to select events.
• Click in the upper-right corner of local menu to enter alarm center to select events.

1. Select Exception Type to set its linkage actions.

Event Hint

Set Event Hint 0

Figure 6-20 Exceptions

4. Set the arming schedule. Refer to Configure Arming Schedule for details.

5. Click Apply.

6.5.2 Perimeter Protection

Perimeter protection includes line crossing detection, intrusion detection, region entrance detection, and region exiting detection.

OU Note

Perimeter protection is only available for certain device models or camera models.

Line Crossing Detection

Line crossing detection detects people, vehicles, and objects crossing a set virtual line. The detection direction can be set as bidirectional, from left to right or from right to left.

Steps

1. Go to Configuration ^ Event ^ Perimeter Protection ^ Line Crossing .
2. Set Camera.
3. Select VCA Mode.

By NVR

The event will be analyzed by NVR. The device can analyze videos that contain human and vehicle. Only the target of selected type (human or vehicle) will trigger alarms, which can reduce false alarms that are caused by other objects.

By Camera

The event will be analyzed by camera.

1. Turn on Enable.
2. Set the detection rules and detection areas.
3. Set Arming Area.
4. Set Direction as A<->B, A->B, or A<-B.

A<->B

Only the arrow on the B side shows. An object crossing a configured line in both directions can be detected and trigger alarms.

A->B

Only an object crossing the configured line from the A side to the B side can be detected.

B->A

Only an object crossing the configured line from the B side to the A side can be detected.

1. Click Max. Size and draw a quadrilateral in the preview window to set the maximum draw area size.
2. Click Min. Size and draw a quadrilateral in the preview window to set the minimum draw area size.
3. Click Draw Area and draw a quadrilateral in the preview window by specifying four vertexes of the detection region.
4. Adjust Sensitivity. Sensitivity allows you to calibrate how readily movement triggers the alarm. A higher value results in the more readily to triggers motion detection.
5. Optional: Set Detection Target as Human or Vehicle to discard alarms which are not triggered by human or vehicle.

C® Note

This function is only available for certain models.

1. Set the arming schedule. Refer to Configure Arming Schedule for details.
2. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
3. Click Apply.

Intrusion Detection

Intrusion detection function detects people, vehicles, or objects that enter and loiter in a pre­defined virtual region.

Steps

1. Go to Configuration ^ Event ^ Perimeter Protection ^ Intrusion .
2. Select Camera to configure.
3. Turn on Enable.
4. Set the detection rules and detection areas.
5. Select Arming Area.
6. Adjust Time Threshold and Sensitivity.

Sensitivity

The size of the object that can trigger the alarm. The higher the value is, the more easily the detection alarm will be triggered. Its range is [1-100].

Time Threshold

Range [1s-10s], the threshold for the time of the object loitering in the region. When the duration of the object in the defined detection area is longer than the set time, the alarm will be triggered.

1. Optional: Set Target Detection as Human or Vehicle to discard alarms which are not triggered by human body or vehicle.

C® Note

This function is only available for certain models.

1. Click Draw Area and draw a quadrilateral in the preview window by specifying four vertexes of the detection region.
2. Set the arming schedule. Refer to Configure Arming Schedule for details.
3. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
4. Click Apply.

Region Entrance Detection

Region entrance detection function detects people, vehicle or other objects which enter a pre­defined virtual region from the outside place, and some certain actions can be taken when the alarm is triggered.

Steps

1. Go to Configuration ^ Event ^ Smart Event ^ Region Entrance .
2. Select Camera to configure.
3. Check Enable Region Entrance Detection.
4. Check Save VCA Picture to save the captured pictures of VCA detection.
5. Set the detection rules and detection areas.
6. Select Arming Area. Up to 4 arming areas are selectable.
7. Click Draw Area and draw a quadrilateral in the preview window by specifying four vertexes of the detection region.
8. Adjust Sensitivity. Sensitivity: Range [0-100]. The higher the value is, the more easily the detection alarm can be triggered.
9. Set the arming schedule.
10. Set the linkage actions.
11. Click Apply.

Region Exiting Detection

Region exiting detection function detects people, vehicle or other objects which exit from a pre­defined virtual region, and some certain actions can be taken when the alarm is triggered.

Steps

1. Go to Configuration ^ Event ^ Smart Event ^ Region Exiting .
2. Select Camera to configure.
3. Check Enable Region Exiting Detection.
4. Check Save VCA Picture to save the captured pictures of VCA detection.
5. Set the detection rules and detection areas.
6. Select Arming Area. Up to 4 arming areas are selectable.
7. Click Draw Area and draw a quadrilateral in the preview window by specifying four vertexes of the detection region.
8. Adjust Sensitivity. Sensitivity: Range [0-100]. The higher the value is, the more easily the detection alarm can be triggered.
9. Set the arming schedule.
10. Set the linkage actions.
11. Click Apply.
    • 1. Non-Video Event

Configure non-video event.

Steps

1. Go to Configuration ^ Device Management ^ Non-Video Event.
2. Select the device.
3. Select the Alarm Content.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply_o
   • 1. Other Events

Thermal Camera Detection

The device supports the event detection modes of thermal network cameras: fire detection, temperature detection, etc. You can configure the arming schedule and linkage actions of the selected event.

Before You Start

Add a thermal network camera to your device and make sure the camera is activated.

Steps

1. Go to Configuration ^ Event ^ Other Events .
2. Select a thermal camera detection event.
3. Set Camera.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply.
   • 1. Configure Arming Schedule

Steps

1. Click Arming Schedule.
2. Choose one day of a week and set the time segment. Up to eight time periods can be set within each day.

[Z@Note

Time periods shall not be repeated or overlapped.

Figure 6-21 Set Arming Schedule

1. Click Apply.
   • 1. Configure Alarm Linkage Action

Configure Full Screen Monitoring

When an alarm is triggered, the local monitor displays in full screen the video image from the alarming channel configured for full screen monitoring. And when the alarm is triggered simultaneously in several channels, you must configure the auto-switch dwell time.

Steps

1. Go to Configuration ^ System ^ Live View ^ General .
2. Set the event output and dwell time.

Event Output

Select the output to show event video.

Full Screen Monitoring Dwell Time

Set the time in seconds to show alarm event image. If alarms are triggered simultaneously in several channels, their full-screen images will be switched at an interval of 10 seconds (default dwell time).

1. Go to Linkage Action interface of the alarm detection.
2. Select Full Screen Monitoring alarm linkage action.
3. Select the channel(s) in Trigger Channel settings you want to make full screen monitoring.

OS Note

Auto-switch will terminate once the alarm stops and back to the live view interface.

Configure Audio Warning

The audio warning enables the video recorder to trigger an audible beep when an alarm is detected.

Steps

1. Go to Configuration ^ System ^ Live View ^ General .
2. Enable Audio Output and set Volume.
3. Go to Linkage Action interface of the alarm detection.
4. Select Audio Warning alarm linkage action.

Notify Surveillance Center

The video recorder can send an exception or alarm signal to the remote alarm host when an event occurs. The alarm host refers to the computer installed with client software (e.g., iVMS-4200, iVMS-5200).

Steps

1. Log into video recorder in web browser.
2. Go to Configuration ^ Network ^ Advanced Settings ^ Other .
3. Set Alarm Host IP and Alarm Host Port.
4. In local menu, go to Linkage Action interface of the alarm detection.
5. Select Notify Surveillance Center.

Configure Email Linkage

The video recorder can send an email with alarm information to a user or users when an alarm is detected.

Steps

1. Switch to easy mode.
2. Go to Configuration ^ System ^ Network ^ Email .
3. Configure the Email settings.
4. Go to Linkage Action interface of the alarm detection.
5. Select Send Email alarm linkage action.

Trigger Alarm Output

The alarm output can be triggered by the normal and smart events.

Steps

1. Go to Linkage Action interface of the alarm input or event detection.
2. Click Trigger Alarm Output.
3. Select the alarm outputs to trigger.
4. Go to Configuration ^ System ^ Event ^ Normal Event ^ Alarm Output .
5. Select an alarm output item from the list. Refer to Alarm Outputfor the alarm output settings.

Configure PTZ Linkage

Video recorder can trigger the PTZ actions (e.g., call preset/patrol/pattern) when the alarm event, or VCA detection events occur.

Steps

1. Go to Linkage Action interface of the alarm input or VCA detection.
2. Select PTZ Linkage.
3. Select the camera to perform the PTZ actions.
4. Select the preset/patrol/pattern No. to call when the alarm events occur.

PTZ Linkage

PTZ Linkage [D1] IPCamera 01 –

(• Preset No. 5 –

C Patrol No. 1

OPattern No. 1

Figure 6-22 PTZ Linkage

CU Note

You can set one PTZ type only for the linkage action each time.

6.6 Recording Management

• • 1. Configure Recording Schedule

Video recorder will automatically start/stop recording according to the configured schedule.

Configure Continuous Recording

Steps

1. Go to Configuration ^ Record ^ Parameter .
2. Set the continuous main stream/sub-stream recording parameters for the camera.
3. Go to Configuration ^ Record ^ Schedule .
4. Select recording type as Continuous.

Configure Event Recording

You can configure the recording triggered by the normal event or smart event.

Steps

1. Go to Configuration ^ Event .
2. Configure the event detection and select the cameras to trigger the recording when event occurs.
3. Go to Configuration ^ Record ^ Parameter .
4. Set the continuous main stream/sub-stream recording parameters for the camera.
5. Go to Configuration ^ Record ^ Schedule .
6. Select recording type as Event.

Edit Schedule

Steps

1. Go to Configuration ^ Record ^ Schedule .

Figure 6-23 Recording Schedule

• Continuous: Continuous recording.
• Event: Recording triggered by all event triggered alarm.

1. Select a camera in Camera No.
2. Check Enable.
3. Configure the recording schedule.
4. Click Edit.
5. Select a day to configure in Weekday.
6. To set an all-day recording schedule, check All Day and select schedule Type.
7. To set other schedules, uncheck All Day and set Start/End time and schedule Type.

CSNote

Up to 8 periods can be configured for each day. And the time periods cannot be overlapped with each other.

1. Click OK to save the settings and go back to upper level menu.

Edit

Figure 6-24 Edit Schedule

Ü@Note

You can also Click to select schedule type as ContinuousorEvent.and On the table, drag the mouse on the desired period to draw a colored bar.

1. Click Apply.
   • 1. Configure Recording Parameter

Main stream refers to the primary stream that affects data recorded to the hard disk drive and will directly determine your video quality and image size. Comparing with the sub-stream, the main stream provides a higher quality video with higher resolution and frame rate.

Sub-stream is a second codec that runs alongside the mainstream. It allows you to reduce the outgoing internet bandwidth without sacrificing your direct recording quality. Sub-stream is often exclusively used by smartphone applications to view live video. Users with limited internet speeds may benefit most from this setting.

Steps

1. Go to Configuration ^ Record ^ Parameter to configure camera main stream and sub-stream parameters.
2. Configure recording parameters.

Frame Rate

Frame rate refers to how many frames are captured each second. A higher frame rate is advantageous when there is movement in the video stream, as it maintains image quality throughout.

Resolution

Image resolution is a measure of how much detail a digital image can hold: the greater the resolution, the greater the level of detail. Resolution can be specified as the number of pixel­columns (width) by the number of pixel-rows (height), e.g.,1024×768.

Bitrate

The bit rate (in kbit/s or Mbit/s) is often referred to as speed, but actually defines the number of bits/time unit and not distance/time unit.

Enable H.264+

The H.264+ mode helps to ensure the high video quality with a lowered bitrate. It can effectively reduce the need of bandwidth and HDD storage space.

Audio Source

The audio input signal source. If you select Audio Source as Camera Audio, it will transmit audio via coaxial cable, and make the local audio input signal unavailable. Ensure the camera supports to transmit audio via coaxial cable before selecting Audio Source as Camera Audio.

C®Note

Audio Source is only available for certain models.

1. Click Apply.
   • 1. Storage Device

Initialize HDD

If it is the first time you use your HDD, please initialize it after it is installed.

Before You Start

Install at least an HDD to your video recorder.

Steps

1. Go to Configuration ^ Record ^ Storage .
2. Select an HDD.
3. Click Init.

Repair Database

Repair an HDD that with error in database. Please operate it with the help of professional technical support.

Secure Erase

Secure erase will delete videos in the selected disk(s).

Add Network Disk

You can add the allocated NAS or IP SAN disk to the video recorder, and use it as a network HDD.

Steps

1. Go to Configuration ^ Record ^ Storage .
2. Click Add.
3. Select NetHDD.
4. Set Type as NAS or IPSAN.
5. Enter NetHDD IP address.
6. Click Search to search the available disks.
7. Select NAS disk from the list, or manually enter the directory in NetHDD Directory.
8. Click OK.

Result

The added NetHDD will be displayed in the storage device list.

• • 1. Configure Storage Mode

Configure HDD Quota

Each camera can be configured with an allocated quota for storing videos.

Steps

1. Go to Configuration ^ Record ^ Storage Mode .
2. Select Mode as Quota.
3. Select a camera to set quota in Camera.
4. Enter the storage capacity in the text fields of Max. Record Capacity (GB) and Max. Picture Capacity (GB).

Mode ® Quota O Group

A Free Quota Space 931 GB

Figure 6-25 Quota

dJNote

When the quota capacity is set to 0, all cameras will use the total capacity of HDD for videos and pictures.

1. Click Apply.
2. Reboot the video recorder to activate the new settings.
   • 1. Advanced Settings

Steps

1. Go to Configuration ^ Record ^ Advanced Settings .
2. Configure the parameters as your desire.

Overwrite

• Disable: When the HDD is full, video recorder will stop writing.
• Enable: When hard drive is full, video record will continue to write new files by deleting the oldest files.

Enable HDD Sleeping

HDDs which are free of working for a long time will turn into sleep status.

1. Maintenance
   1. Restore Default

Steps

1. Click 0 at the upper-right corner.
2. Select the restoring type.

Simple Restore

Restore all parameters, except the network (including IP address, subnet mask, gateway, MTU, NIC working mode, default route, server port, etc.) and user account parameters, to the factory default settings.

Factory Defaults

Restore all parameters to the factory default settings.

Restore to Inactive

Restore the device to the inactive status, and leave all settings unchanged except restoring user accounts.

1. Click Yes. The device will reboot automatically.
   1. Search Log

The operation, alarm, exception and information of video recorder can be stored in logs, which can be viewed and exported at any time.

Steps

1. Go to Maintenance ^ More .
2. Set the search conditions.
3. Click Search.
   1. Advanced Settings

Steps

1. Go to Configuration ^ Network ^ Advanced Settings .
2. Configure the parameters as your desire.

RTSP

You can specifically secure the stream data of live view by setting the RTSP authentication.

RTSP Authentication Type

Two authentication types are selectable, if you select digest, only the request with digest authentication can access the video stream by the RTSP protocol via the IP address. For security reasons, it is recommended to select digest as the authentication type.

ISAPA

ISAPI (Internet Server Application Programming Interface) is an open protocol based on HTTP, which can realize the communication between the system devices (e.g., network camera, NVR, etc.). The video recorder is as a server, the system can find and connect the video recorder.

HTTP

The admin user account can disable the HTTP service from the GUI or the web browser. After the HTTP is disabled, all the related services, including the ISAPI, Onvif and Gennetc, will terminate as well.

HTTP Authentication

If you need to enable the HTTP service, you can set the HTTP authentication to enhance the access security. Two authentication types are selectable, for security reasons, it is recommended to select digest as the authentication type.

IP Camera Occupation Detection

The function detects the network camera status. If the network camera has been added by another video recorder, the network camera status will show as □ in Online Device list.

1. Click Apply.
   1. Buzzer Switch

You can enable or disable buzzer with alarm linkage or exceptional linkage.

Steps

1. Click ® at the upper-right corner.
2. Click More.
3. Go to Buzzer Switch.
4. Turn on or turn off Enable.
   1. Device Maintenance
      1. Schedule Reboot

The device will automatically restart according to the schedule.

Steps

1. Click El at the upper-right corner.
2. Click More.
3. Go to Device Maintenance ^ Schedule Reboot .
4. Turn on Enable.
5. Set the reboot schedule.
6. Click Apply.
   • 1. Camera Upgrade

Upgrade the camera(s) in the added device list.

Steps

1. ClickMaintenance ( ) ^ More ^ Deice Maintenance ^ Camera Upgrade.
2. Click Check for Updates.
3. Upgrade camera.

• Select the channel to upgrade, and click the Upgrade on the right.
• Click Quick Upgrade to upgrade all channels that have updates.
  • 1. Device Status

You can mute the selected channel(s).

Steps

1. Click El at the upper-right corner.
2. Click More.
3. Go to Device Maintenance ^ Device Status .
4. In the Mute and Not Disturb column, check the corresponding channel(s).

Result

The selected channel(s) will be muted.

• 1. Upgrade

/»\ Warning

Do not shutdown or turn off the power during upgrade.

• • 1. Local Upgrade

Before You Start

Store the upgrade firmware to a backup device, and connect it to your device.

Steps

1. Go to Maintenance .
2. Click O near Firmware.
3. Select a backup device in Device Name.
4. Select the upgrade firmware.
5. Click Upgrade. Your device will reboot automatically.
   • 1. Online Upgrade

Upgrade the device with the latest online firmware.

Before You Start

Enable HiLookVision and configure its parameters. Refer to HiLookVision for details.

Steps

1. Go to Maintenance .
2. Click O .
3. Go to Online Upgrade .
4. Download the latest firmware.

Auto Download The will automatically check and download the latest firmware.

Test Upgrade Click Test Upgrade to manually check and download the latest firmware. 5. Upgrade your device if a new firmware version is available. The device will reboot automatically.

1. Alarm

When events occur, you can view their details in alarm center.

• 1. Set Event Hint

Select the events to hint in alarm center.

Steps

1. Click in the upper-right corner of local menu to enter alarm center.
2. Select Exception, Basic Event, or Smart Event to configure as your desire.

Figure 8-1 Alarm Centre

1. Click ft and select events to hint.
2. Click OK.

When the selected events occur, the alarm information will be displayed (locating in upper­right corner of local menu).

• 1. View Alarm in Alarm Center

Steps

1. Click in upper-right corner of local menu.
2. Select Exception, Basic Event, or Smart Event to view as your desire.
3. Web Operation
   1. Introduction

You can get access to the video recorder via web browser.

You may use one of the following listed web browsers: Internet Explorer 11.0, Apple Safari, Mozilla Firefox, and Google Chrome. The supported resolutions include 1024×768 and above.

For certain models, you will have to download a web component plug-in, and install it. Otherwise, a few functions would be unavailable. The download address is http://

hikdownload.ys7.com/web/webplugin/windows/WebComponents/standard/ WebComponents.exe .