Analog Speed Dome, DVR, Coaxial Cable, RS-485 Cable

How to Control Analog Speed Dome by Pelco-D/P Protocol

1. Connect DVR and Analog PTZ Camera

• • 1.1 Power on analog PTZ camera

The pigtails of analog speed dome (take speed dome for short in next contents) is

shown in Figure 1-1, it includes three kinds of cables: coaxial cable, power cable and 485 cable (for PTZ control).

Figure 1-1 pigtail of analog PTZ camera

Connect power cable of speed dome and relative power adapter, as shown in Figure 1-2.

Note: Red cable is positive cable and black is negative one in the pigtail of speed dome power cable, yellow one represents ground(no need to connect), power cable of speed dome is self-adaptive, so you don’t need to concern the connect order.

Figure 1-2 Connect PTZ camera power cable and adapter cable

• 1.2 Connect PTZ camera and coaxial cable

Power on DVR, connect speed dome and DVR analog channel by coaxial cable.

Then you can see live view of speed dome on DVR as shown in Figure 1-3.

Figure 1-3 live view of speed dome on DVR

• 1.3 Connect 485 cable and speed dome

485 cables are two signal cables in a UTP cable. One should connect 485 pigtail of speed dome and DVR 485 port, take Figure 1-4 as example.

485 cable has polarity order, this is different from power cable connection.

Figure 1-4 Connect DVR 485 port and analog

• 2. Parameters Configuration

  • 2.1 Speed dome parameter configuration

The main parameter configuration of speed dome is the Baud rate and Address configuration, you can set these on OSD menu of speed dome.

• 2.1.1 Call OSD menu of speed dome

You can call OSD menu of speed dome by Menu bar or 95th preset.

Step-1: Click PTZ Control in DVR live view page, then enter PTZ control page, like Figure 2-1.

Figure 2-1 Click PTZ control in DVR live view page

Step 2: Click OSD menu on PTZ control page.

If you control speed dome using UTC PTZ protocol you can call OSD menu by click Menu bar like illustration in Figure 2-2.

Figure 2-2 Method-1: Call OSD menu by Menu bar (only work under UTC protocol)

If the PTZ protocol is not UTC, you should call 95^th preset to call the OSD menu,

like the operation in Figure 2-3.

Figure 2-3 Method-2: Call OSD menu by click 95^th preset (works for all protocols)

The OSD menu of speed dome is shown in Figure 2-4.

Figure 2-4 OSD menu of speed dome

• 2.1.2 Set the Baud Rate and Address of speed dome.

Enter the SYS SETTING in speed dome by steps illustrated from Figure 2-5 to Figure 2-7.

Figure 2-5 Enter SYS SETTINGS

Figure 2-6 Enter SYS INFO SETTING

Set Address and Baud rate of speed dome in Figure 2-7, also you should enable SOFT ADDR ACT and SOFT BAUD ACT. The soft address is valid address for connecting the speed dome when SOFT ADDR ACT is ON, the selectable soft address rage is from 0/1(Pelco-D/P) to 255. The soft baud rate is the valid baud rate for the speed dome when SOFT BAUD ACT. Is enabled, with 2400, 4800, 9600 and 19200 selectable.

Figure 2-7 Set BAUD Rate and Address parameters

• 2.2 DVR configuration

You can configure DVR parameters by both web and local side.

2.2.1 Configure on local side

As illustration in Figure 2-8, enter PTZ Parameter Settings on PTZ control page.

Figure 2-8 Select protocol on PTZ control page

In PTZ control menu, set parameters of Baud rate, Data Bit, PTZ Protocol and

Address as shown in Figure 2-9 .

Figure 2-9 Select PTZ protocol(Pelco-D/Pelco-P)

• 2.2.2 Configure on web side

If you want to configure DVR parameters on web page, you should complete the settings in Configuration>System>System Settings>RS-485,(shown in Figure 2-10), all the configurations should be the same as the relative parameters in speed dome.

Figure 2-10 Set parameters on web page

• 3. Configuration test

Through configurations above, you can test if the configuration success. Take Figure 3-1 as example, you can see the live view page changed, which means the configuration works.

Figure 3-1 Configuration test

<p>The post How to Control Analog Speed Dome by Pelco-D/P Protocol first appeared on NVR IPCAMERA SECURITY.</p>

Hence this article is all about default CCTV default password.

So this article is not limited to a particular “CCTV default password“,  it covers almost all the brands but if few brands are missing kindly mention in the comment. I try to cover almost all IP addresses and passwords but few products have a unique code that will mention in their user manual.

So below is the list of CCTV default passwords and Usernames.

1. Hikvision Default Password and IP address

Hikvision one of the best CCTV camera brands all over the world and it has many customers around the world. Sometimes they need to know for the default password of the Hikvsion’s devices. Here is the default password of Hikvision’s devices.

Username: admin

Password: 12345

IP address: 192.0.0.64/192.168.1.64

IP Tool: Download SADP Tool

For new models, you can reset the password via the SADP tool. Please click the link below and follow the instructions on the pdf file

CP Plus CCTV Default Password 

Username:  admin
Password:  admin
IP Address:  192.168.1.108 / 192.168.1.240

2. Dahua default IP address and password

Dahua default IP address is in the series of  192.168.1.XXX and if you need to change IP address then you need to follow the below link “How to change Dahua IP address“.

Username-admin

Password-admin

For DVR and NVR, following are the  default accounts:

• admin/admin admin/123456 (master account of local and network accessing)
• 888888/888888 (local administrator)
• 666666/666666 (restricted user)
• default / default (hidden user)

3. CP Plus IP camera default IP address

User name: admin
Password: admin
IP Address :  192.168.1.108 / 192.168.1.240

CP PLUS IP camera address finder tool

If cameras being used on 3rd party recorders or you need to configure a large number of cameras. The first step will be to use the Tools to find and configure the IP address and the local area network. Here is the link to the CP PLUS IP camera address finder tool.

4. Axis camera default IP

Axis camera User name: root
Password: pass
default IP: 192.168.0.90

5. Bosch camera default IP

For old models:
Username: service
Bosch IP camera default password: service
IP Address: 192.168.0.1
For new models:
You can reset the camera by pushing the reset button about 8 seconds.

6. GEOVISION default password

Username: admin
Password: admin
IP Address: 192.168.1.108

7. TVT  IP camera default IP

DVR and NVR

Username: admin
Password: 123456
IP Address: 192.168.226.201

IP Camera

Username: admin
Password: 123456
IP Address: 192.168.226.201

8. Gobbler default IP address and password

Username: admin
Password: 123456

9. Panasonic default IP address and password

User name: admin
Password: 12345
IP Address:  192.168.0.253/10.1.1.12/192.168.0.10

10. SONY default IP address and password

Username: admin

Password: admin

IP Address: 192.168.0.100

11. Samsung default IP address and password and Samsung DVR default password

User name: admin
Password: 4321/111111/1111111
IP Address: 192.168.1.200

12. Ubiquiti default password

Username: ubnt
Password: ubnt
IP Address: 192.168.1.20

13. Mobotix camera default password.

Mobotix:
Username: admin
Password: meinsm

14. Messoa  default IP address and password

Username: admin
Password: 1234 or model number of camera or
IP address: 192.168.1.30

15. LTS Security default IP address and password

Username: admin
Password: 12345/123456
IP Address: 192.0.0.64

16. Speco default IP address and password

Speco
For old models:
Username: root /admin
Password: root/admin/1234

17. Canon default IP address and password

Username: root
Password: camera model number
IP Address: 192.168.100.1

17. Cisco default IP address and password

Username: No Username
Password: No Password
IP Address: 192.168.0.100

18. FLIR default IP address and password

Username: admin
Password: fliradmin
IP Address: 192.168.250.116

19. Foscam default IP address and password

Username: admin
Password: Blank
IP Address: search By IP tool, Click here to download

20. Honeywell default IP address and password

Username: administrator
Password: 1234
IP Address: DHCP enabled

Honeywell IP Utility is a free program that enables users to configure the IP network settings, name device(s), upgrade firmware and change passwords.

21. PELCO default IP address and password

Username: admin
Password: admin
IP Address: DHCP enabled

21. QVIS default IP address and password

Username: Admin
Password: 1234
IP Address: 192.168.0.250

22. SANYO default IP address and password

Username: admin
Password: admin
IP Address: 1192.168.0.2

23. Toshiba default IP address and password

Username: root
Password: ikwb
IP Address: 192.168.0.30

24.  3xLogic default IP address and password

Username: admin
Password: 12345
IP Address: 192.0.0.64

25.  Basler default IP address and password

Username: admin
Password: admin
IP Address: 92.168.100.x

26.  CNB default IP address and password

Username: root
Password: admin
IP Address: 192.168.123.100

27.  DIGISOL default IP address and Password

Username: admin
Password: 888888
IP Address: 192.168.1.10

28. Uniview default IP address and password

Username: admin
Password: 123456
IP Address: DHCP enable.

Uniview IP camera address finder tool

If cameras being used on 3rd party recorders. The first step will be to use the EZTools software on a PC to find the IP address of the cameras and then you change according to your local network. The second step will change the camera protocol to ONVIF. Here is the download link of EZ tool.

29. LILIN default IP address and password

Username: admin
Password: 1111
IP Address: 63.110.100.xxx/DHCP Enable

30. Trendnet default IP address and Password

Username: admin
Password: admin
IP Address: 192.168.10.1

I hope this information is helpful to you.  If you have any query, please write to us in the comment box below.

<p>The post Current CCTV default password List NEW first appeared on NVR IPCAMERA SECURITY.</p>