Chapter 1 Startup

1.1 Activate Your Device

For the first-time access, you need to activate the video recorder by setting an admin password. No operation is allowed before activation. You can also activate the video recorder via web browser, SADP or client software.

Before You Start

Power on your device.

Steps

1. Select a language.
2. Click Next.
3. Input the same password in Password and Confirm Password.

/¡K Warning

Strong Password recommended-We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

1. Activate network camera(s) connected to the device.

• Check Use Device Password as Default to use the device password to activate the inactive network camera(s).
• Enter a password to activate network camera(s).

1. Optional: Set an email address for password resetting. When you forget your password, you can reset it by email.
2. Check Enable.
3. Enter an email address.
4. Click Activate.

User Name admin

Password

Weak

Confirm Password

Camera Activation Password 0 Use Device Password as Default

Email to Reset Password 0 Enable

Email Address

Hilook 4K NVR Device Complete Guide

Read More :

1. Hilook Hikvision Password Reset NVR/DVR/IPCAM NEW
2. Hilook Firmware Software Tools
3. How to Find The Encryption/Verification Code? Hilook Hikvision Annke

Figure 1-1 Activation

1.2 Login

• • 1. Set Unlock Pattern

Admin user can use the unlock pattern to login. You can configure the unlock pattern after the device is activated.

Steps

1. Use the mouse to draw a pattern among the 9 dots on the screen. Release the mouse when the pattern is done.

03 Note

• The pattern shall have 4 dots at least.
• Each dot can be connected for once only.

1. Draw the same pattern again to confirm it. When the two patterns match, the pattern is configured successfully.

Unlock Pattern

Set Unlock Pattern

Release your finger when done

Figure 1-2 Set

Set Unlock Pattern

Draw pattern again to confirm

• • 1. Log in via Unlock Pattern

Steps

1. Right click the mouse on live view interface.

Figure 1-3 Draw the Unlock Pattern

2. Draw the pre-defined pattern to unlock to enter the menu operation.

nXlNote

• If you have forgotten your pattern, you click Forgot My Pattern or Switch User to log in via password.
• If you have drawn the wrong pattern for more than 5 times, the system will switch to the normal login mode automatically.
  • 1. Log in via Password

If your video recorder has logged out, you must login before operating the menu and other functions.

Steps

1. Select User Name.

Welcome

Figure 1-4 Login Interface

1. Input password.
2. Click Login.

• When you forget the password of the admin, you can click Forgot Password to reset the password.
• If you enter the wrong password 7 times, the current user account will be locked for 60 seconds.

Chapter 2 Live View

• 1. GUI Introduction
• Click Target Detection at the upper-left corner, and select or to display the specified live target detection results. For result details, click View More.

HU Note

° Target Detection is only available for certain models.

° Target Detection is valid when HDD is installed.

° 0 is valid for motion detection, line crossing detection, intrusion detection, and facial detection.

• Click to start/stop auto-switch. The screen will automatically switch to the next one.
• Click to enter full screen mode.
• Double click a camera to view it in single-screen mode. Double click again to exit single-screen mode.
• Change a camera live view screen by dragging it from its screen to the desired screen.
• Scroll up/down to turn to previous/next screen.
• Position the cursor on a camera to show shortcut menu.

Figure 2-1 Shortcut Menu

Table 2-1 Shortcut Menu Description

• In the live view interface, there are icons at the upper-right corner of the screen for each

camera, showing the camera recording and alarm status.

Table 2-2 Live View Icon Description

• Right click your mouse to display the shortcut menu.

Menu

Ei Single Screen >

S Window Division >

< Previous Screen

> Next Screen

O Si art All! D-swHch

EJ Camera

® Playback

a FTZ Control

Figure 2-2 Right Click Shortcut Menu

• 1. PTZ Control
     1. Configure PTZ Parameter

You shall configure PTZ parameters before controlling a PTZ camera.

Steps

1. Preview a camera in live view and click 0 on shortcut menu.

2. Click PTZ Parameter Settings.

Figure 2-3 PTZ Settings

Figure 2-4 PTZ Parameter

1. Set the PTZ camera parameters.

C0Note

• All parameters should be the same as the PTZ camera.
• For the Coaxitron camera/dome connected, you can select the PTZ protocol to UTC (Coaxitron). Ensure the selected protocol is supported by the connected camera/dome.
• The AHD and HDCVI cameras support coaxitron control.
• Selecting Coaxitron protocol will make other parameters unavailable, including baud rate, data bit, stop bit, parity and flow control.

1. Click OK.
   • 1. PTZ Control Panel Introduction

Table 2-3 PTZ Panel Description

• • 1. Customize Preset

Set a preset location where the PTZ camera would point to when an event occurs.

Steps

1. Preview a camera in live view and click on shortcut menu.
2. Select a desired preset in preset list.
3. Use direction buttons to wheel the camera to required locations. Adjust zoom and focus as your desire.
4. Click 1* .

What to do next

Double click a preset in the preset list to call it.

• • 1. Customize Patrol

Patrol refers to a path consists of a series of presets with designated sequence. It provides dynamic live image for monitoring several presets.

Steps

1. Preview a camera in live view and click on shortcut menu.
2. Click Patrol.
3. Select a desired patrol.
4. Click Set.
5. Click + .
6. Configure key point parameters, such as the key point No., duration of staying for one key point and speed of patrol. The key point is corresponding to the preset. The preset number determines the order at which the PTZ will follow while cycling through the patrol. Duration refers to the time span to stay at the corresponding key point. Speed defines the speed at which the PTZ will move from one key point to the next.

Figure 2-5 Patrol Settings

1. Click Apply.

What to do next

Select a patrol and click Call to call it. The PTZ camera will move according the predefined patrol path.

Patroll ▼

Set Call

Figure 2-6 Call Preset

• • 1. Customize Pattern

A pattern records the movement path and dwell time in a certain position. When you call a pattern, the PTZ camera will move according to the recorded path.

Steps

1. Preview a camera in live view and click on shortcut menu.
2. Click Pattern.
3. Select a pattern.
4. Click Record.
5. Use direction buttons to wheel the camera to required locations. Adjust zoom and focus as your desire.
6. Click Stop Recording. The previous PTZ camera moving path is recorded as a pattern.

What to do next

Select a pattern and click Call to call it. The PTZ camera will move according the predefined

pattern.

Chapter 3 Playback

• 1. GUI Introduction

Go to Playback .

Figure 3-1 Playback

Table 3-1 Playback Interface Description

Figure 3-2 Timeline

• Position the cursor on the timeline, drag the timeline to position to a certain time.
• Period marked with blue bar contains video. Red bar indicates the video in the period is event video.
• Scroll up/down to zoom out/in timeline.
  1. Normal Playback

Play back normal videos.

Steps

1. Go to Playback .
2. Select a camera from the camera list.
3. Select a date on the calendar for playback.

C®Note

The blue triangle at the calendar date corner indicates there are available videos. For example, means video is available. 22 means no video.

1. Optional: Position the cursor on playback window to show control bar.

Figure 3-3 Control Bar

Table 3-2 Button Description

• 1. Smart Playback

The smart playback function provides an easy way to get through the less effective information. When you select the smart playback mode, the system will analyze the video containing the motion detection, line crossing detection, or intrusion detection information.

Before You Start

Configure motion detection, line crossing detection, and intrusion detection rules and detection areas.

Steps

1. Go to Playback .
2. Click Smart.
3. Select a camera.

Figure 3-4 Smart Playback Interface

4. Position the cursor on playback window to show control bar.

Figure 3-5 Control Bar

Table 3-3 Button Description

Normal Video

Set normal video playback speed. The option is only valid when Do not Play Normal Videos is unchecked.

Play Speed of Smart/Custom Video

Set playback speed of videos with smart information. The option is only valid when Do not

Play Normal Videos is enabled.

Play Strategy

Do not Play Normal Videos 0

Normal Video

—- _ ——— X 8

Play Speed of Smart/Custom Video

—————— X1

Cancel

Figure 3-6 Play Strategy

3.4 Back up Clip

You can clip videos during playback. Video clips can be exported to the backup device (USB flash drives, USB HDDs, USB writer, SATA writer, etc.).

Before You Start

Connect a backup device to your video recorder.

Steps

1. Start playback. Refer to Normal Playback for details.
2. Click .
3. Clip videos.

• Click Q, set start and end time, click OK.
• Set a time segment on time bar for clipping.

Figure 3-7 Time Segment

1. Click [7] .
2. Click Export to export the clip to backup device.
3. Search File

Steps

1. Go to Search .
2. Set search conditions.
3. Click Search.

• Click to play the video.
• Click to lock the file. Locked file will not be overwritten.
• Select file(s), and click Export to export file(s) to backup device.

System Date

System Time

Resolution

Enable Wizard

Enable Password

Enable NTP

Interval (min)

NTP Server

NTP Port

1. Configuration (Easy Mode)

Easy mode contains basic configurations. Go to Configuration , and click Easy Mode.

• 1. System Configuration
     1. General

You can configure the output resolution, system time, mouse pointer speed, etc.

Steps

1. Go to Configuration ^ System ^ General .

02-09-2019

19:35:38 ©

1024‘768i60HZ

□

0

□

60

time.windows com

123

Figure 5-1 General Settings

1. Configure the parameters as your desire.

Enable Wizard

The wizard will pop up after the device starts up.

Enable Password

You need to enter password for authentication if the device automatically logged out.

Enable NTP

Network time protocol (NTP) is a networking protocol for time synchronization. The device can connect to NTP (network time protocol) server to sync time.

Interval (min)

Time interval between two time synchronization with NTP server.

NTP Server

IP address of the NTP server.

NTP Port

Port of the NTP server.

1. Click Apply.
   • 1. User

Add User

There is a default account: Administrator. The administrator user name is admin. Administrator has the permission to add, delete, and edit user. Guest user only has live view, playback, and log search permission.

Steps

1. Go to Configuration ^ User .
2. Click Add and confirm your admin password.

Figure 5-2 Add User

1. Enter user name.
2. Enter the same password in Password and Confirm.

/ * \ Warning

We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

1. Click OK.

– Click / to edit user.

Set Password Resetting Email

When you forgot your login pattern and password, the device will send an email contains verification code to your email for password resetting.

Steps

1. Go to Configuration ^ User .
2. Click Password Resetting Email.
3. Enter admin password for authorization.
4. Enter an email address.
5. Click OK.

Reset Password

You can reset your password when you forgot your login pattern and password.

Steps

1. Click Forgot Password at the password login interface.
2. Click Next if you agree the Privacy Policy, you can scan the QR code to read it.
3. Follow the wizard to reset password.

5.1.3 Exception

You can receive exception events hint in alarm center, and set exception linkage actions.

Steps

1. Go to Configuration ^ System ^ Exception .
2. Optional: Configure event hint. When the set events occur, you will receive hints in alarm center.
3. Check Event Hint.
4. Click at the upper-right corner of local menu to enter alarm center.
5. Select an event type.
6. Click Set to select events to hint.
7. Set Exception Type
8. Select Normal Linkage and Trigger Alarm Output type for exception linkage actions.

□ Audible Warning □ 10.96.15.145:8000->1

□ 10.96.15.1 45:8000->2

□ Notify Surveillance Center

□ Send Email

Figure 5-3 Exceptions

1. Click Apply.

5.2 Network Configuration

• • 1. General

You shall properly configure the network settings before operating the device over network.

Steps

1. Go to Configuration ^ Network ^ General .

DHCP

IPv4 Address

IPv4 Subnet Mask

IPv4 Default Gateway

Obtain DNS Automatically 0

Preferred DNS Server

Alternate DNS Server

Figure 5-4 Network

1. Set network parameters.

DHCP

If the DHCP server is available, you can check Enable DHCP to automatically obtain an IP address and other network settings from that server.

Obtain DNS Automatically

If DHCP is checked. You can check Obtain DNS Automatically to automatically obtain

Preferred DNS Server and Alternate DNS Server.

1. Click Apply.
   • 1. HiLookVision

HiLookVision provides mobile phone application and platform service to access and manage your connected devices, which enables you to get a convenient remote access to the video security system.

Steps

1. Go to Configuration ^ Network ^ Platform Access .
2. Select Access Type as HiLookVision.
3. Check Enable. The service terms will pop up.
4. Scan the QR code to read the service terms and privacy statement.
5. Check I have read and agree to Service Terms and Privacy Statement. if you agree the service terms and privacy statement..
6. Click OK.
7. Optional: Check Stream Encryption. It requires to enter verification code in remote access and live view after this function is enabled.
8. Optional: Check Custom, and edit Server Address.
9. Enter a code in Verification Code. You can click Refresh to randomly generate a verification code.
10. Bind your device with a HiLookVision account.
11. Use a smart phone to scan the QR code, and download HiLookVision app. You can also download it from https://appstore.hikvision.com, or the QR code below. Refer to HiLookVision Mobile Client User Manual for details.

Figure 5-5 Download HiLookVision

2) Use HiLookVision to scan the device QR, and bind the device.

Hl® Note

If the device is already bound with an account, you should unbind with the current account.

1. Click Apply.

What to do next

You can access your video recorder via HiLookVision.

• • 1. Email

Set an email account to receive event notification.

Before You Start

• Ensure your video recorder is in a local area network with an SMTP mail server.
• Configure your network parameters. Refer to General for details.

Steps

1. Go to Configuration ^ Network ^ Email .

Server Authentication

User Name

Password

SMTP Server

SMTP Port

SSUTLS

Attached Picture

Sender

Sender’s Address

Select Receivers

Receiver

Receiver’s Address

Figure 5-6 Email

1. Set email parameters

Server Authentication

(Optional), check it to enable the server authentication feature.

User Name

The user account of email sender for SMTP server authentication.

Password

The password of email sender for SMTP server authentication.

SSL/TLS

(Optional), check it to enable SSL/TLS if it required by the SMTP server.

Sender

The sender name.

Sender’s Address

The sender’s email address.

Select Receiver

Select a receiver. Up to 3 receivers are available.

Receiver

The receiver name.

Receiver’s Address

The receiver’s email address.

djNote

• For network cameras, the event images are directly sent as the email attachment. One network camera only sends one picture.
• For analog cameras, 3 attached pictures will be sent for one analog camera when an event occurs.

1. Click Apply.

5.3 Camera Management

• • 1. Network Camera

Add Network Camera by Device Password

Add network cameras which the password is the same as your video recorder.

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct. Refer to General for details.
• Ensure the network camera password is the same as your video recorder.

Steps

1. Go to Configuration ^ Camera ^ IP Camera . The online cameras on the same network segment with your video recorder are displayed in the camera list.

+ Ql UI 0 9 Search!-

□ No. I IP Address I Edit I Add/Delete I Security I Status I Camera Name

… 10.6.114.36 ~ + ©Active A

Figure 5-7 IP Camera Management Interface

1. Click + to add the camera.

Add Network Camera Manually

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.
• Ensure the network camera is activated.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click + .
3. Set network camera parameters, including IP address, protocol, management port, etc. You can check Use IPC Active Password to use the device password to add network camera(s).
4. Optional: Click Add More to add another network camera.
5. Click OK.

Figure 5-8 Add Network Camera

Edit Connected Network Camera

You can edit the IP address, protocol and other parameters of the added network cameras.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click / to edit the selected camera.

Channel Port

If the connected device is an encoding device with multiple channels, you can select the channel port No. to choose a connecting channel.

1. Click OK.

Sort Channel Order

Channel layout windows are ordered by channel number. You can change the camera linked channel number by dragging windows.

Steps

1. Go to Configuration ^ Camera ^ Camera .
2. Click Sort Channel.
3. Drag a channel window to the channel number as your desire.
4. Click Apply.

C®Note

After sorting channels, the device will reconnect to network cameras.

Configure Remote Settings

For the camera parameters that were only configurable via web browser, remote settings function provides an operation interface to configure remote camera parameters.

Before You Start

Ensure your camera is properly connected.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click Remote Settings
3. After the device resource is initialized, select a camera.
4. Set camera parameters.

Upgrade Network Camera

The Network camera can be remotely upgraded through the device.

Before You Start

• Ensure you have inserted the USB flash drive to the device, and it contains the network camera upgrade firmware.
• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click O .
3. Click Yes to confirm.
4. Select the camera upgrade firmware from your storage device.
5. Click Upgrade to start upgrading. The camera will restarted automatically after upgrade completed.

Configure Advanced Camera Parameters

You can configure advanced camera parameters like camera IP address, camera password, etc.

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click ® .
3. Set camera parameters like IP address, camera password, etc.
4. Click Apply.

5.3.2 OSD Settings

Configure OSD (On-Screen Display) settings for the camera, including date format, camera name, etc.

Steps

1. Go to Configuration ^ Camera ^ OSD .
2. Select a camera.

Figure 5-9 OSD

3. Drag the text frames on the preview window to adjust the OSD position.

4. Click Apply.

5.3.3 Event

Motion Detection

Motion detection enables the video recorder to detect the moving objects in the monitored area and trigger alarms.

Steps

1. Go to Configuration ^ Camera ^ Motion Detection .
2. Select a camera.
3. Check Enable.
4. Set the motion detection area.

• Click Draw Area or Clear to draw or clear areas. The first area is set as full screen by default.
• Click Full Screen to set the motion detection area as full screen. You can drag on the preview window to draw motion detection areas.

C® Note

The operation may differ according to different models.

1. Adjust Sensitivity. Sensitivity allows you to calibrate how readily movement triggers the alarm. A higher value results in the more readily to triggers motion detection.
2. Set analysis mode as AI or PIR.

AI

The motion detection event will be analyzed by your device.

PIR

The motion detection event will be analyzed by certain analog PIR cameras.

1. Optional: Set Target Detection as Human or Vehicle to discard alarms which are not triggered by human or vehicle.

US Note

This function is only available for certain models.

1. Set the arming schedule. Refer to Configure Arming Schedule for details.
2. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
3. Click Apply.

Configure Arming Schedule

Steps

1. Select Arming Schedule.
2. Choose one day of a week and set the time segment. Up to eight time periods can be set within each day.

djNote

Time periods shall not be repeated or overlapped.

Figure 5-10 Set Arming Schedule

1. Click Apply.

Configure Alarm Linkage Action

Alarm linkage actions will be activated when an alarm or exception occurs.

Steps

1. Click Linkage Action.

Figure 5-11 Linkage Actions

2. Set normal linkage actions, trigger alarm output, trigger recording channel, etc.

Full Screen Monitoring

The local monitor will display the alarming channel image in full screen when an alarm is triggered. It requires to select the alarming channel(s) in Trigger Channel.

Audible Warning

It will trigger an audible beep when an alarm is triggered.

Notify Surveillance Center

The device will send an exception or alarm signal to the remote client software when an alarm is triggered.

Send Email

It will send an email with alarm information when an alarm is triggered.

PTZ Linkage

It will trigger PTZ actions (e.g., call preset/patrol/pattern) when smart events occur.

3. Click Apply.

5.4 Device Management

• • 1. Switch

Add and manage switches.

Quick Add Switch

Quick add switch(es) in the same network segment with the video recorder. If the switch is not activated, it will be added with the channel default password.

Steps

1. Go to Configuration ^ Device Management ^ Switch.
2. In the Online Device List, check the switch(es) to be added and click Add to add switch(es) in the same network segment with the video recorder using the channel default password.

Add Switch Manually

Steps

1. Go to Configuration ^ Device Management ^ Switch .
2. In the Online Device List, click Add and set the parameters of the channel.

Table 5-1 Channel Parameter Description

3. Click Add and Continue and repeat operation until all device have been added.

4. Click Add.

5.4.2 Non-Video Event

Configure non-video event.

Steps

1. Go to Configuration ^ Device Management ^ Non-Video Event.
2. Select the device.
3. Select the Alarm Content.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply_o

5.5 Recording Management

• • 1. Storage Device

Initialize HDD

A newly installed hard disk drive (HDD) must be initialized before it can be used to save videos and information.

Before You Start

Install at least an HDD to your video recorder. For detailed steps, refer to Quick Start Guide.

Steps

1. Go to Configuration ^ Record ^ Storage .
2. Select an HDD.
3. Click Init.

Repair Database

Repair an HDD that with error in database. Please operate it with the help of professional technical support.

Secure Erase

Secure erase will delete videos in the selected disk(s).

Add Network Disk

You can add the allocated NAS or IP SAN disk to the video recorder, and use it as a network HDD.

Steps

1. Go to Configuration ^ Record ^ Storage .
2. Click Add.
3. Select NetHDD.
4. Set Type as NAS or IPSAN.
5. Enter NetHDD IP address.
6. Click Search to search the available disks.

Figure 5-12 Add NetHDD

7. Select NAS disk from the list, or manually enter the directory in NetHDD Directory.

8. Click OK. The added NetHDD will be displayed in the storage device list.

5.5.2 Configure Recording Schedule

Video recorder will automatically start/stop recording according to the configured schedule.

Configure Continuous Recording

Steps

1. Go to Configuration ^ Record ^ Parameter .
2. Set the continuous main stream/sub-stream recording parameters for the camera. Refer to Configure Recording Parameter for details.
3. Go to Configuration ^ Record ^ Schedule .
4. Select recording type as Continuous. Refer to Edit Schedule for details.

Configure Event Recording

You can configure the recording triggered by the motion detection, line crossing detection, and intrusion detection.

Steps

1. Go to Configuration ^ Event ^ Smart Event .
2. Configure the event detection and select the channels to trigger the recording when an event occurs.
3. Go to Configuration ^ Record ^ Parameter .
4. Set the continuous main stream/sub-stream recording parameters for the camera. Refer to Configure Recording Parameter for details.
5. Go to Configuration ^ Record ^ Schedule .
6. Select recording type as Event. Refer to Edit Schedule for details.

Edit Schedule

Steps

1. Go to Configuration ^ Record ^ Schedule .

Figure 5-13 Recording Schedule

Continuous

Continuous recording.

Event

Recording triggered by all event triggered alarm.

1. Select a camera in CameraNo.
2. Check Enable.
3. Configure the recording schedule.

Edit a. Click Edit.

Schedule b. Select a day to configure in Weekday.

1. To set an all-day recording schedule, check All Day and select schedule type.
2. To set other schedules, uncheck All Day, and set Start/End Time and schedule type.

Note

Up to 8 periods can be configured for each day. And the time periods cannot be overlapped with each other.

1. Click OK to save the settings and go back to upper level menu.

Figure 5-14 Edit Schedule

1. Click to select schedule type as Continuous or Event.

Draw

Schedule

5. Click Apply.

1. On the table, drag the mouse on the desired period to draw a colored bar.

5.5.3 Configure Recording Parameter

Steps

1. Go to Configuration ^ Record ^ Parameter .
2. Configure recording parameters.

Main Stream

Main stream refers to the primary stream that affects data recorded to the hard disk drive and will directly determine your video quality and image size. Comparing with the sub­stream, the main stream provides a higher quality video with higher resolution and frame rate.

Sub-Stream

Sub-stream is a second codec that runs alongside the mainstream. It allows you to reduce the outgoing internet bandwidth without sacrificing your direct recording quality. Sub-stream is often exclusively used by smartphone applications to view live video. Users with limited internet speeds may benefit most from this setting.

Frame Rate

Frame rate refers to how many frames are captured each second. A higher frame rate is advantageous when there is movement in the video stream, as it maintains image quality throughout.

Resolution

Image resolution is a measure of how much detail a digital image can hold: the greater the resolution, the greater the level of detail. Resolution can be specified as the number of pixel­columns (width) by the number of pixel-rows (height), e.g.,1024×768.

Bitrate

The bit rate (in Kbit/s or Mbit/s) is often referred to as speed, but actually defines the number of bits/time unit and not distance/time unit.

C® Note

Higher resolution, frame rate, and bitrate provide you better video quality, but it also requires more internet bandwidth and uses more storage space on the hard disk drive.

1. Click Apply.

Chapter 6 Configuration (Expert Mode)

Go to Configuration , and click Expert Mode at the lower-left corner.

• 1. System Configuration
     1. General

Configure Basic Settings

You can configure the language, system time, output resolution, mouse pointer speed, lock screen password, etc.

Go to Configuration ^ System ^ General ^ Basic Settings , configure the parameters as your desire, and click Apply.

Language

The default language is English.

VGA/HDMI Resolution

Select the output resolution, which must be the same with the resolution of the VGA/HDMI display.

Lock Screen Password

You need to enter password for authentication if the screen is locked.

Mouse Pointer Speed

Set the speed of mouse pointer. 4 levels are configurable.

Wizard

The wizard will pop up after the device starts up.

Enhanced Decoding Mode

Disabling enhanced decoding mode will reduce the local decoding capability by half and restart the device.

Configure DST Settings

DST (Daylight Saving Time) refers to the period of the year when clocks are moved one period ahead. In some areas worldwide, this has the effect of creating more sunlit hours in the evening during months when the weather is the warmest.

Go to Configuration ^ System ^ General ^ DST Settings , configure the parameters as your desire, and click Apply.

Configure More Settings

You can configure your device name, lock screen time, output mode, etc.

Go to Configuration ^ System ^ General ^ More Settings , configure the parameters as your desire, and click Apply.

Device Name

Edit the video recorder name.

Device No.

The number is required in the connection with remote control, network keyboard, etc. Edit the serial number of video recorder. The device number ranges from 1 to 255, and the default value is 255.

Lock Screen

Set timeout time for lock screen.

Menu Output Mode

Choose output to display local menu.

Figure 6-1 More Settings

• • 1. Live View

Configure General Parameters

You can configure the output interface, mute or turning on the audio, event output interface, etc.

Steps

1. Go to Configuration ^ System ^ Live View ^ General .

Enable Audio Output

Volume

Figure 6-2 Live View-General

1. Configure the Live View parameters.

Live View Mode

Select the live view window division.

Dwell Time

The time to dwell in a camera before switching to next camera when auto-switch in live view is enabled.

Event Output

Select the output to show event video.

Full Screen Monitoring Dwell Time

Set the time to show alarm event image.

Enable Audio Output

Turn on/off audio output for the selected video output.

Volume

Adjust the live view, playback, and two-way audio volume for the selected video output interface.

1. Click Apply.

Configure Live View Layout

Steps

1. Go to Configuration ^ System ^ Live View ^ View .
2. Select Video Output Interface to configure.
3. Click to select a window and click a camera No. in the camera list you would like to display. + means no camera is displayed on the window.
4. Optional: Click Q / f? to start/stop live view of all the cameras in order.
5. Click Apply.

Configure Channel-Zero Encoding

Enable the channel-zero encoding when you need to get a remote view of many channels in real time from a web browser or CMS (Client Management System) software, in order to decrease the bandwidth requirement without affecting the image quality.

Steps 1. Go 2. Set 3. Go

to Configuration ^ System ^ Live View ^ General . Video Output Interface as Channel-Zero.

to Configuration ^ System ^ Live View ^ Channel-Zero .

Enable Channel-Zero Encoding

Frame Rate

Max. Bitrate Mode

Max. Bitrate(Kbps)

Figure 6-3 Channel-Zero

1. Check Enable Channel-Zero Encoding.
2. Configure Frame Rate, Max. Bitrate Mode, and Max. Bitrate. The higher frame rate and bitrate settings result in higher bandwidth requirement.
3. Click Apply.

6.1.3 User

Refer to User for details.

6.2 Network Configuration

• • 1. TCP/IP

TCP/IP must be properly configured before you operate video recorder over network.

Steps

1. Go to Configuration ^ Network ^ General ^ TCP/IP .
2. Configure network parameters.

Working Mode

Multi-address Mode

The parameters of the two NIC cards can be configured independently. You can select LAN1 or LAN2 in the NIC type field for parameter settings. You can select one NIC card as default route. And then the system is connecting with the extranet and the data will be forwarded through the default route.

Net-fault Tolerance Mode

The two NIC cards use the same IP address, and you can select the Main NIC to LAN1 or LAN2. By this way, in case of one NIC card failure, the video recorder will automatically enable the other standby NIC card so as to ensure the normal running of the whole system.

Load Balance Mode

By using the same IP address and two NIC cards share the load of the total bandwidth, which enables the system to provide two Gigabit network capacity.

C® Note

Working mode is only available for certain models.

NIC Type

Select NIC type as your desire. If your device supports Wi-Fi dongle function, the NIC of Wi-Fi dongle would be selectable after a suitable Wi-Fi dongle is installed.

DHCP

If the DHCP server is available, you can check Enable DHCP to automatically obtain an IP address and other network settings from that server.

MTU

The maximum transmission unit (MTU) is the size of the largest network layer protocol data unit that can be communicated in a single network transaction.

Default Route

Select a route as your desire. If your device supports Wi-Fi dongle function, the route of Wi-Fi dongle would be selectable after a suitable Wi-Fi dongle is installed.

Auto Obtain DNS

If DHCP is checked. You can check Obtain DNS Automatically to obtain Preferred DNS Server and Alternate DNS Server.

1. Click Apply.
   • 1. DDNS

Dynamic domain name server (DDNS) maps dynamic user IP addresses to a fixed domain name server.

Before You Start

Register DynDNS, PeanutHull and NO-IP services with your ISP.

Steps

1. Go to Configuration ^ Network ^ General ^ DDNS .

Enable 0

DDNS Type DynDNS ▼

Server Address

Device Domain Name

User Name

Password

Status DDNS is disabled

Figure 6-4 DDNS

1. Check Enable.
2. Select a DDNS type.
3. Enter parameters including service address, domain name, etc.
4. Click Apply.

What to do next

You can view DDNS status in Status.

• • 1. NAT

Two ways are provided for port mapping to realize the remote access via the cross-segment network, UPnP™ and manual mapping.

Before You Start

Enable the UPnP™ function of your router if UPnP™ is required. When the device network working mode is multi-address, the default device route should be on the same network segment as the LAN IP address of the router.

Steps

1. Configuration ^ Network ^ General ^ NAT .
2. Check Enable.
3. Select Mapping Type as Manual or Auto

Auto The port mapping items are read-only, and the external ports are set by the router automatically. You can click Refresh to get the latest status of the port mapping.

Manual Select an external port type. Click / to edit External Port. You can use the default external port No., or change it according to actual requirements. External Port indicates the port No. for port mapping in the router.

The value of the RTSP port No. should be 554 or between 1024 and 65535, while the value of the other ports should be between 1 and 65535 and the value must be different from each other. If multiple devices are configured for the UPnP™ settings under the same router, the value of the port No. for each device should be unique.

1. Set the virtual server of your router, including internal source port, external source port, etc. The virtual server parameters shall be corresponding with your device port.
   • 1. Ports (More Settings)

Set different port types to enable relevant functions as your desire.

Go to Configuration ^ Network ^ General ^ More Settings .

Alarm Host IP/Port

The device will send the alarm event or exception message to the alarm host when an alarm is triggered. The remote alarm host must have the client management system (CMS) software installed.

Alarm Host IP refers to the IP address of the remote PC on which the CMS software (e.g., iVMS-4200) is installed, and the Alarm Host Port (7200 by default) must be the same as the alarm monitoring port configured in the software.

Server Port

For remote client software access. Ranges from 2000 to 65535. The default value is 8000.

HTTP Port

For remote web browser access. The default value is 80.

Multicast IP

Multicast can be configured to enable live view for cameras that exceed the maximum number allowed through network. A multicast IP address covers Class-D IP ranging from 224.0.0.0 to 239.255.255.255 and it is recommended to use the IP address ranging from 239.252.0.0 to 239.255.255.255.

When adding a device to the CMS software, the multicast address must be the same as that of the device.

RTSP Port

RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and communications systems to control streaming media servers. The port is 554 by default.

Output Bandwidth Limit

You can check the checkbox to enable output bandwidth limit.

Output Bandwidth

After enable the output bandwidth limit, input the output bandwidth.

CUl Note

• The output bandwidth limit is used for the remote live view and playback.
• The default output bandwidth is the maximum limit.

Figure 6-5 Port Settings

6.2.5 Upload Logs to the Server

You can upload system logs to the server for backup.

Steps

1. Go to Configuration ^ Network ^ General ^ Log Server Settings .

Enable

Upload Time Interval (Fi) 1

Server IP Adtfress

Port 514

Apply

Figure 6-6 Log Server Settings

1. Turn on Enable
2. Set Upload Time Interval, Server IP Address, and Port.
3. Optional: Click Test to test if parameters are valid.
4. Click Apply.
   • 1. HiLookVision

Go to Configuration ^ Network ^ Platform Access . Refer to HiLookVision for details.

• • 1. Email

Go to Configuration ^ Network ^ Email . Refer to Email for details.

6.3 Camera Management

• • 1. Network Camera

Add Automatically Searched Online Network Camera

Add the network cameras to your video recorder.

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.
• Ensure the network camera password is the same as your video recorder.

Steps

1. Go to Configuration ^ Camera ^ Camera ^ IP Camera .
2. Click Online Device. The online cameras on the same network segment will be displayed in the list.

+ Qi ICT O 9 Searchl-

□ No. I IP Address I Edit I Add/Delete I Security I Status I Camera Name

… 10.6.114.36 ~ + ©Active A

Figure 6-7 Online Device

1. Select a network camera, and click Add to add it.

Add Network Camera Manually

Add the network cameras to your video recorder.

Before You Start

• Ensure your network camera should be in the same network segment with your video recorder.
• Ensure the network connection is valid and correct.
• Activate the network camera to add.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click + .

Figure 6-8 Add IP Camera

3. Enter information of the network camera to add.

Use Channel Default Password

If it is checked, the video recorder will add the camera by the set channel default password.

4. Click Add.

Add Network Camera on Different Network Segment

If your network camera is on a different network segment, the device can search its IP address within a range of IP addresses, and add it.

Before You Start

• Ensure the network connection is valid and correct.
• Ensure the network camera password is the same as your video recorder.

Steps

1. Go to Configuration ^ Camera ^ Camera ^ IP Channel .
2. Click Advanced Search.
3. Enter Network Segment.

first three octets the camera IP address.

O If your network camera is not on the same network segment with the NVR and s… ,

□ Network Segment 192 . 168 . 0 . 0

□ Network Segment 192. 168.1 . ~

| Cancel

Figure 6-9 Enter Network Segment

1. Click Add.

Add Network Camera Through Plug-and-Play

If an inactive network camera or third party ONVIF camera is connected to your network, the video recorder may automatically detect and add the camera, or notify you to manually add it.

Steps

1. Go to Configuration ^ Camera ^ Camera ^ IP Channel .
2. Click More.
3. Select Plug-and-Play.
4. Optional: Enable Auto Add Network Camera. The video recorder would automatically detect and add the inactive network camera or third party ONVIF camera.

Plug-and-Play x

Auto Add Network Camera «

OK

Figure 6-10 Auto Add Network Camera

‘Note

If you turn off Auto Add Network Camera, when an inactive network camera or third party ONVIF camera is connected to your network, the video recorder would automatically detect it and notify you to add it.

Edit Connected Network Camera

You can edit the IP address, protocol and other parameters of the added network cameras.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click / of an added network camera.

Channel Port

If the connected device is an encoding device with multiple channels, you can choose the channel to connect by selecting the channel port No. in the drop-down list.

1. Click OK.

Example

Enter an example that illustrates the current task (optional).

What to do next

Enter the tasks the user should do after finishing this task (optional).

Upgrade Network Camera

The Network camera can be remotely upgraded through the device.

Before You Start

• Ensure you have inserted the USB flash drive to the device, and it contains the network camera upgrade firmware.
• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.

Steps

1. Go to Configuration ^ Camera ^ Camera .
2. Click .
3. Click Yes to confirm.
4. Select the camera upgrade firmware from your storage device.
5. Click Upgrade to start upgrading. The camera will restarted automatically after upgrade completed.

Add Network Camera Through PoE

The PoE interfaces enable the device to transfer electrical power and data to connected PoE cameras. And the PoE interface supports the Plug-and-Play function. Connectable PoE camera number varies with device models. If you disable a PoE interface, you can also use it to connect to an online network camera.

Add PoE Camera

Steps

1. Go to Configuration ^ Camera ^ Camera ^ PoE Settings .
2. Enable or disable long network cable mode by selecting Long Distance or Short Distance.

Long Distance

Long-distance (100 to 300 meters) network transmissions via PoE interface.

Short Distance

Short-distance (< 100 meters) network transmission via PoE interface.

C® Note

• The PoE ports are enabled with the short distance mode by default.
• The bandwidth of IP camera connected to the PoE via long network cable (100 to 300 meters) cannot exceed 6 Mbps.
• The allowed max. long network cable may be less than 300 meters depending on different IP camera models and cable materials.
• When the transmission distance reaches 100 to 250 meters, you must use the CAT5e or CAT6 network cable to connect with the PoE interface.
• When the transmission distance reaches 250 to 300 meters, you must use the CAT6 network cable to connect with the PoE interface.

Figure 6-11 Add PoE Camera

1. Click Apply.
2. Connect PoE cameras to your device PoE interfaces with network cables.

What to do next

The connected PoE camera will be displayed in Configuration ^ Camera ^ Camera ^ IP Channel .

You can click its status to view live image.

Add Non-PoE Network Camera

You can use the PoE channel resource to connect a non-PoE network camera.

Steps

1. Go to Configuration ^ Camera ^ Camera ^ IP Channel .
2. Click jo of a channel with no linked network camera.
3. Select Adding Method as Manual.

Plug-and-Play

The camera is physically connected to the PoE interface. You can click ® in the added device list to edit its parameters.

Manual

Add IP camera without physical connection via network cable.

1. Set other parameters, such as user name, password, and IP address.

Configure Advanced Camera Parameters

You can configure advanced camera parameters like camera IP address, camera password, etc.

Before You Start

• Ensure your network camera is on the same network segment with your video recorder.
• Ensure the network connection is valid and correct.

Steps

1. Go to Configuration ^ Camera ^ Camera .
2. Click ® .
3. Set camera parameters like IP address, camera password, etc.
4. Click Apply.

Configure Channel Type

You can disable a PoE channel to additionally increase a normal IP channel resource.

Go to Configuration ^ Camera ^ Camera ^ PoE Binding Configuration , and set the PoE channel as your desire.

Figure 6-12 PoE Binding Configuration

Sort Channel Order

Go to Configuration ^ Camera ^ Camera . Refer to Sort Channel Order for details.

Configure Remote Settings

Go to Configuration ^ Camera ^ Camera . Refer to Configure Remote Settings for details.

Import/Export IP Camera Configuration File

The information of added network camera can be generated into an excel file and exported to the local device for backup, including the IP address, manage port, password of admin, etc. And the exported file can be edited on your computer, like adding or deleting the content, and copy the setting to other devices by importing the excel file to it.

Before You Start

Connect a backup device like USB flash drive to your video recorder.

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click El
3. Click Export to export configuration files to the connected backup device.
4. To import a configuration file, select the file from the selected backup device and click Import. After the importing process is completed, you must reboot the video recorder.

Advanced Settings

Steps

1. Go to Configuration ^ Camera ^ IP Camera .
2. Click O .
3. Configure the parameters as your desire.

H.265 Auto Switch Configuration

If you enable the option, video recorder will automatically switch to H.265 stream for the network camera (which supports H.265 video format) for the initial access.

Upgrade

Upgrade the added network cameras.

Channel Default Password Management

Change the default password of activating and adding network camera.

• • 1. Display Settings

Configure the OSD (On-Screen Display), image settings, exposure settings, day/night switch settings, etc.

Steps

1. Go to Configuration ^ Camera ^ Display .
2. Select Camera.
3. Configure parameters as your desire.

OSD Settings

Configure the OSD (On-screen Display) settings for the camera, including date/time, camera name, etc.

Image Settings

Customize the image parameters including the brightness, contrast, and saturation for the live view and recording effect.

Exposure

Set the camera exposure time (1/10000 to 1 sec). A larger exposure value results in a brighter image.

Day/Night Switch

The camera can be set to day, night, or auto switch mode according to the surrounding illumination conditions.

Backlight

Set the camera’s wide dynamic range (0 to 100). When the surrounding illumination and the object have large differences in brightness, you should set the WDR value.

Image Enhancement

For optimized image contrast enhancement.

OSD Settings

Image Settings

Exposure

Day/Night Switch

Backlight

Image Enhancement

Camera Parameters Settings

Camera

Camera Name

Camera 01

Figure 6-13 OSD

4. Drag the text frames on the preview window to adjust the OSD position.

5. Click Apply.

• • 1. Privacy Mask

You are allowed to configure the privacy mask areas that cannot be viewed or recorded.

Steps

1. Go to Configuration ^ Camera ^ Privacy Mask .
2. Select Camera.
3. Check Enable.

Clear Area 1

□ Clear Area 2

□ Clear Area 3

□ Clear Area 4

Clear All

Camera

Enable

Figure 6-14 Privacy Mask

4. Drag to draw an area on the window. The frames of the areas will be marked with different colors.

OZlNote

Up to 4 privacy mask areas can be configured. The size of each area can be adjusted.

5. Click Apply.

6.4 Device Management

• • 1. Switch

Add and manage switches.

Quick Add Switch

Quick add switch(es) in the same network segment with the video recorder. If the switch is not activated, it will be added with the channel default password.

Steps

1. Go to Configuration ^ Device Management ^ Switch.
2. In the Online Device List, check the switch(es) to be added and click Add to add switch(es) in the same network segment with the video recorder using the channel default password.

Add Switch Manually

Steps

1. Go to Configuration ^ Device Management ^ Switch .
2. In the Online Device List, click Add and set the parameters of the channel.

Table 6-1 Channel Parameter Description

3. Click Add and Continue and repeat operation until all device have been added.

4. Click Add.

6.5 Event Configuration

• • 1. Normal Event

Motion Detection

Motion detection enables the video recorder to detect the moving objects in the monitored area and trigger alarms.

Steps

1. Go to Configuration ^ Camera ^ Motion Detection .
2. Select a camera.
3. Check Enable.
4. Set the motion detection area.

• Click Draw Area or Clear to draw or clear areas. The first area is set as full screen by default.
• Click Full Screen to set the motion detection area as full screen. You can drag on the preview window to draw motion detection areas.

1. Adjust Sensitivity. Sensitivity allows you to calibrate how readily movement triggers the alarm. A higher value results in the more readily to triggers motion detection.
2. Set analysis mode as AI or PIR.

AI

The motion detection event will be analyzed by your device.

PIR

The motion detection event will be analyzed by certain analog PIR cameras.

1. Optional: Set Target Detection as Human or Vehicle to discard alarms which are not triggered by human or vehicle.
2. Set the arming schedule. Refer to Configure Arming Schedule for details.
3. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
4. Click Apply.

Video Tampering

Trigger alarm when the lens is covered and take alarm response actions.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Video Tampering .

Figure 6-15 Video Tampering

1. Set Camera.
2. Turn on Enable.
3. Adjust Sensitivity as your desire. The higher the value is, the more easily the video tampering can be triggered.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply.

Video Loss

Detect video loss of a camera and take alarm response actions.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Video Loss .
2. Set Camera.
3. Turn on Enable.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply.

Alarm Input

Set linkage actions for an external sensor alarm.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Alarm Input .

Figure 6-16 Alarm Input

Note

Local alarm input: Local alarm input is triggered by the external device that connected to the video recorder’s terminal block.

1. Click jo of a desired alarm input.

Figure 6-17 Edit Alarm Input

1. Customize Alarm Name.
2. Set alarm type as N.O (normally open) or N.C (normally closed).
3. Set Settings as Input to enable the function.

C®Note

If you set Settings as Nonuse, the alarm input will be disabled. If you set Settings as One-Key Disarming, the selected linkage method(s) of the alarm input will be disabled.

1. Set the arming schedule. Refer to Configure Arming Schedule for details.
2. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
3. Click Apply.

Alarm Output

Trigger an alarm output when an alarm is triggered.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Alarm Output .

Figure 6-18 Alarm Output

1. Click <o of a desired alarm output.
2. Customize Alarm Name.
3. Select Dwell Time.

Figure 6-19 Edit Alarm Output

1. Set Settings as Input to enable the function.
2. Set the arming schedule. Refer to Configure Arming Schedule for details.
3. Click Apply.

Flashing Light Alarm Output

When light and audio alarm camera is connected, you can set the flashing time, flashing frequency, and arming schedule of the flashing light alarm.

Before You Start

Light and audio alarm camera is connected.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Flashing Light Alarm Output.
2. Click E for any row.
3. Set the Flashing Time and Flashing Frequency.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. ClickSave.

Audio Alarm Output

When light and audio alarm camera is connected, you can set the parameters and arming schedule of the audio alarm.

Before You Start

Light and audio alarm camera is connected.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Flashing Light Alarm Output.
2. Click S for any row.
3. Select the Audio Type as Alarm Sound, Prompt Sound, or Custom Audio.

CHjNote

• When you select the Alarm Sound, you also need to select the alarm sound type.
• When you select the Alarm Sound, you also need to upload the custom audio, enter the audio name and select the uploaded audio in the drop-down box of Custom Audio.

1. Set the Alarm Times and Sound Volume.
2. Set the arming schedule. Refer to Configure Arming Schedule for details.
3. ClickSave.

Exception

Exception events can be configured to take the event hint in the live view window and trigger alarm outputs and linkage actions.

Steps

1. Go to Configuration ^ Event ^ Normal Event ^ Exception .
2. Configure event hint. When the set events occur, you will receive hints in alarm center.
3. Enable Event Hint.
4. Select events to hint. Choose from:

• Click @ of Event Hint Configuration to select events.
• Click in the upper-right corner of local menu to enter alarm center to select events.

1. Select Exception Type to set its linkage actions.

Event Hint

Set Event Hint 0

Figure 6-20 Exceptions

4. Set the arming schedule. Refer to Configure Arming Schedule for details.

5. Click Apply.

6.5.2 Perimeter Protection

Perimeter protection includes line crossing detection, intrusion detection, region entrance detection, and region exiting detection.

OU Note

Perimeter protection is only available for certain device models or camera models.

Line Crossing Detection

Line crossing detection detects people, vehicles, and objects crossing a set virtual line. The detection direction can be set as bidirectional, from left to right or from right to left.

Steps

1. Go to Configuration ^ Event ^ Perimeter Protection ^ Line Crossing .
2. Set Camera.
3. Select VCA Mode.

By NVR

The event will be analyzed by NVR. The device can analyze videos that contain human and vehicle. Only the target of selected type (human or vehicle) will trigger alarms, which can reduce false alarms that are caused by other objects.

By Camera

The event will be analyzed by camera.

1. Turn on Enable.
2. Set the detection rules and detection areas.
3. Set Arming Area.
4. Set Direction as A<->B, A->B, or A<-B.

A<->B

Only the arrow on the B side shows. An object crossing a configured line in both directions can be detected and trigger alarms.

A->B

Only an object crossing the configured line from the A side to the B side can be detected.

B->A

Only an object crossing the configured line from the B side to the A side can be detected.

1. Click Max. Size and draw a quadrilateral in the preview window to set the maximum draw area size.
2. Click Min. Size and draw a quadrilateral in the preview window to set the minimum draw area size.
3. Click Draw Area and draw a quadrilateral in the preview window by specifying four vertexes of the detection region.
4. Adjust Sensitivity. Sensitivity allows you to calibrate how readily movement triggers the alarm. A higher value results in the more readily to triggers motion detection.
5. Optional: Set Detection Target as Human or Vehicle to discard alarms which are not triggered by human or vehicle.

C® Note

This function is only available for certain models.

1. Set the arming schedule. Refer to Configure Arming Schedule for details.
2. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
3. Click Apply.

Intrusion Detection

Intrusion detection function detects people, vehicles, or objects that enter and loiter in a pre­defined virtual region.

Steps

1. Go to Configuration ^ Event ^ Perimeter Protection ^ Intrusion .
2. Select Camera to configure.
3. Turn on Enable.
4. Set the detection rules and detection areas.
5. Select Arming Area.
6. Adjust Time Threshold and Sensitivity.

Sensitivity

The size of the object that can trigger the alarm. The higher the value is, the more easily the detection alarm will be triggered. Its range is [1-100].

Time Threshold

Range [1s-10s], the threshold for the time of the object loitering in the region. When the duration of the object in the defined detection area is longer than the set time, the alarm will be triggered.

1. Optional: Set Target Detection as Human or Vehicle to discard alarms which are not triggered by human body or vehicle.

C® Note

This function is only available for certain models.

1. Click Draw Area and draw a quadrilateral in the preview window by specifying four vertexes of the detection region.
2. Set the arming schedule. Refer to Configure Arming Schedule for details.
3. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
4. Click Apply.

Region Entrance Detection

Region entrance detection function detects people, vehicle or other objects which enter a pre­defined virtual region from the outside place, and some certain actions can be taken when the alarm is triggered.

Steps

1. Go to Configuration ^ Event ^ Smart Event ^ Region Entrance .
2. Select Camera to configure.
3. Check Enable Region Entrance Detection.
4. Check Save VCA Picture to save the captured pictures of VCA detection.
5. Set the detection rules and detection areas.
6. Select Arming Area. Up to 4 arming areas are selectable.
7. Click Draw Area and draw a quadrilateral in the preview window by specifying four vertexes of the detection region.
8. Adjust Sensitivity. Sensitivity: Range [0-100]. The higher the value is, the more easily the detection alarm can be triggered.
9. Set the arming schedule.
10. Set the linkage actions.
11. Click Apply.

Region Exiting Detection

Region exiting detection function detects people, vehicle or other objects which exit from a pre­defined virtual region, and some certain actions can be taken when the alarm is triggered.

Steps

1. Go to Configuration ^ Event ^ Smart Event ^ Region Exiting .
2. Select Camera to configure.
3. Check Enable Region Exiting Detection.
4. Check Save VCA Picture to save the captured pictures of VCA detection.
5. Set the detection rules and detection areas.
6. Select Arming Area. Up to 4 arming areas are selectable.
7. Click Draw Area and draw a quadrilateral in the preview window by specifying four vertexes of the detection region.
8. Adjust Sensitivity. Sensitivity: Range [0-100]. The higher the value is, the more easily the detection alarm can be triggered.
9. Set the arming schedule.
10. Set the linkage actions.
11. Click Apply.
    • 1. Non-Video Event

Configure non-video event.

Steps

1. Go to Configuration ^ Device Management ^ Non-Video Event.
2. Select the device.
3. Select the Alarm Content.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply_o
   • 1. Other Events

Thermal Camera Detection

The device supports the event detection modes of thermal network cameras: fire detection, temperature detection, etc. You can configure the arming schedule and linkage actions of the selected event.

Before You Start

Add a thermal network camera to your device and make sure the camera is activated.

Steps

1. Go to Configuration ^ Event ^ Other Events .
2. Select a thermal camera detection event.
3. Set Camera.
4. Set the arming schedule. Refer to Configure Arming Schedule for details.
5. Set the linkage actions. Refer to Configure Alarm Linkage Action for details.
6. Click Apply.
   • 1. Configure Arming Schedule

Steps

1. Click Arming Schedule.
2. Choose one day of a week and set the time segment. Up to eight time periods can be set within each day.

[Z@Note

Time periods shall not be repeated or overlapped.

Figure 6-21 Set Arming Schedule

1. Click Apply.
   • 1. Configure Alarm Linkage Action

Configure Full Screen Monitoring

When an alarm is triggered, the local monitor displays in full screen the video image from the alarming channel configured for full screen monitoring. And when the alarm is triggered simultaneously in several channels, you must configure the auto-switch dwell time.

Steps

1. Go to Configuration ^ System ^ Live View ^ General .
2. Set the event output and dwell time.

Event Output

Select the output to show event video.

Full Screen Monitoring Dwell Time

Set the time in seconds to show alarm event image. If alarms are triggered simultaneously in several channels, their full-screen images will be switched at an interval of 10 seconds (default dwell time).

1. Go to Linkage Action interface of the alarm detection.
2. Select Full Screen Monitoring alarm linkage action.
3. Select the channel(s) in Trigger Channel settings you want to make full screen monitoring.

OS Note

Auto-switch will terminate once the alarm stops and back to the live view interface.

Configure Audio Warning

The audio warning enables the video recorder to trigger an audible beep when an alarm is detected.

Steps

1. Go to Configuration ^ System ^ Live View ^ General .
2. Enable Audio Output and set Volume.
3. Go to Linkage Action interface of the alarm detection.
4. Select Audio Warning alarm linkage action.

Notify Surveillance Center

The video recorder can send an exception or alarm signal to the remote alarm host when an event occurs. The alarm host refers to the computer installed with client software (e.g., iVMS-4200, iVMS-5200).

Steps

1. Log into video recorder in web browser.
2. Go to Configuration ^ Network ^ Advanced Settings ^ Other .
3. Set Alarm Host IP and Alarm Host Port.
4. In local menu, go to Linkage Action interface of the alarm detection.
5. Select Notify Surveillance Center.

Configure Email Linkage

The video recorder can send an email with alarm information to a user or users when an alarm is detected.

Steps

1. Switch to easy mode.
2. Go to Configuration ^ System ^ Network ^ Email .
3. Configure the Email settings.
4. Go to Linkage Action interface of the alarm detection.
5. Select Send Email alarm linkage action.

Trigger Alarm Output

The alarm output can be triggered by the normal and smart events.

Steps

1. Go to Linkage Action interface of the alarm input or event detection.
2. Click Trigger Alarm Output.
3. Select the alarm outputs to trigger.
4. Go to Configuration ^ System ^ Event ^ Normal Event ^ Alarm Output .
5. Select an alarm output item from the list. Refer to Alarm Outputfor the alarm output settings.

Configure PTZ Linkage

Video recorder can trigger the PTZ actions (e.g., call preset/patrol/pattern) when the alarm event, or VCA detection events occur.

Steps

1. Go to Linkage Action interface of the alarm input or VCA detection.
2. Select PTZ Linkage.
3. Select the camera to perform the PTZ actions.
4. Select the preset/patrol/pattern No. to call when the alarm events occur.

PTZ Linkage

PTZ Linkage [D1] IPCamera 01 –

(• Preset No. 5 –

C Patrol No. 1

OPattern No. 1

Figure 6-22 PTZ Linkage

CU Note

You can set one PTZ type only for the linkage action each time.

6.6 Recording Management

• • 1. Configure Recording Schedule

Video recorder will automatically start/stop recording according to the configured schedule.

Configure Continuous Recording

Steps

1. Go to Configuration ^ Record ^ Parameter .
2. Set the continuous main stream/sub-stream recording parameters for the camera.
3. Go to Configuration ^ Record ^ Schedule .
4. Select recording type as Continuous.

Configure Event Recording

You can configure the recording triggered by the normal event or smart event.

Steps

1. Go to Configuration ^ Event .
2. Configure the event detection and select the cameras to trigger the recording when event occurs.
3. Go to Configuration ^ Record ^ Parameter .
4. Set the continuous main stream/sub-stream recording parameters for the camera.
5. Go to Configuration ^ Record ^ Schedule .
6. Select recording type as Event.

Edit Schedule

Steps

1. Go to Configuration ^ Record ^ Schedule .

Figure 6-23 Recording Schedule

• Continuous: Continuous recording.
• Event: Recording triggered by all event triggered alarm.

1. Select a camera in Camera No.
2. Check Enable.
3. Configure the recording schedule.
4. Click Edit.
5. Select a day to configure in Weekday.
6. To set an all-day recording schedule, check All Day and select schedule Type.
7. To set other schedules, uncheck All Day and set Start/End time and schedule Type.

CSNote

Up to 8 periods can be configured for each day. And the time periods cannot be overlapped with each other.

1. Click OK to save the settings and go back to upper level menu.

Edit

Figure 6-24 Edit Schedule

Ü@Note

You can also Click to select schedule type as ContinuousorEvent.and On the table, drag the mouse on the desired period to draw a colored bar.

1. Click Apply.
   • 1. Configure Recording Parameter

Main stream refers to the primary stream that affects data recorded to the hard disk drive and will directly determine your video quality and image size. Comparing with the sub-stream, the main stream provides a higher quality video with higher resolution and frame rate.

Sub-stream is a second codec that runs alongside the mainstream. It allows you to reduce the outgoing internet bandwidth without sacrificing your direct recording quality. Sub-stream is often exclusively used by smartphone applications to view live video. Users with limited internet speeds may benefit most from this setting.

Steps

1. Go to Configuration ^ Record ^ Parameter to configure camera main stream and sub-stream parameters.
2. Configure recording parameters.

Frame Rate

Frame rate refers to how many frames are captured each second. A higher frame rate is advantageous when there is movement in the video stream, as it maintains image quality throughout.

Resolution

Image resolution is a measure of how much detail a digital image can hold: the greater the resolution, the greater the level of detail. Resolution can be specified as the number of pixel­columns (width) by the number of pixel-rows (height), e.g.,1024×768.

Bitrate

The bit rate (in kbit/s or Mbit/s) is often referred to as speed, but actually defines the number of bits/time unit and not distance/time unit.

Enable H.264+

The H.264+ mode helps to ensure the high video quality with a lowered bitrate. It can effectively reduce the need of bandwidth and HDD storage space.

Audio Source

The audio input signal source. If you select Audio Source as Camera Audio, it will transmit audio via coaxial cable, and make the local audio input signal unavailable. Ensure the camera supports to transmit audio via coaxial cable before selecting Audio Source as Camera Audio.

C®Note

Audio Source is only available for certain models.

1. Click Apply.
   • 1. Storage Device

Initialize HDD

If it is the first time you use your HDD, please initialize it after it is installed.

Before You Start

Install at least an HDD to your video recorder.

Steps

1. Go to Configuration ^ Record ^ Storage .
2. Select an HDD.
3. Click Init.

Repair Database

Repair an HDD that with error in database. Please operate it with the help of professional technical support.

Secure Erase

Secure erase will delete videos in the selected disk(s).

Add Network Disk

You can add the allocated NAS or IP SAN disk to the video recorder, and use it as a network HDD.

Steps

1. Go to Configuration ^ Record ^ Storage .
2. Click Add.
3. Select NetHDD.
4. Set Type as NAS or IPSAN.
5. Enter NetHDD IP address.
6. Click Search to search the available disks.
7. Select NAS disk from the list, or manually enter the directory in NetHDD Directory.
8. Click OK.

Result

The added NetHDD will be displayed in the storage device list.

• • 1. Configure Storage Mode

Configure HDD Quota

Each camera can be configured with an allocated quota for storing videos.

Steps

1. Go to Configuration ^ Record ^ Storage Mode .
2. Select Mode as Quota.
3. Select a camera to set quota in Camera.
4. Enter the storage capacity in the text fields of Max. Record Capacity (GB) and Max. Picture Capacity (GB).

Mode ® Quota O Group

A Free Quota Space 931 GB

Figure 6-25 Quota

dJNote

When the quota capacity is set to 0, all cameras will use the total capacity of HDD for videos and pictures.

1. Click Apply.
2. Reboot the video recorder to activate the new settings.
   • 1. Advanced Settings

Steps

1. Go to Configuration ^ Record ^ Advanced Settings .
2. Configure the parameters as your desire.

Overwrite

• Disable: When the HDD is full, video recorder will stop writing.
• Enable: When hard drive is full, video record will continue to write new files by deleting the oldest files.

Enable HDD Sleeping

HDDs which are free of working for a long time will turn into sleep status.

1. Maintenance
   1. Restore Default

Steps

1. Click 0 at the upper-right corner.
2. Select the restoring type.

Simple Restore

Restore all parameters, except the network (including IP address, subnet mask, gateway, MTU, NIC working mode, default route, server port, etc.) and user account parameters, to the factory default settings.

Factory Defaults

Restore all parameters to the factory default settings.

Restore to Inactive

Restore the device to the inactive status, and leave all settings unchanged except restoring user accounts.

1. Click Yes. The device will reboot automatically.
   1. Search Log

The operation, alarm, exception and information of video recorder can be stored in logs, which can be viewed and exported at any time.

Steps

1. Go to Maintenance ^ More .
2. Set the search conditions.
3. Click Search.
   1. Advanced Settings

Steps

1. Go to Configuration ^ Network ^ Advanced Settings .
2. Configure the parameters as your desire.

RTSP

You can specifically secure the stream data of live view by setting the RTSP authentication.

RTSP Authentication Type

Two authentication types are selectable, if you select digest, only the request with digest authentication can access the video stream by the RTSP protocol via the IP address. For security reasons, it is recommended to select digest as the authentication type.

ISAPA

ISAPI (Internet Server Application Programming Interface) is an open protocol based on HTTP, which can realize the communication between the system devices (e.g., network camera, NVR, etc.). The video recorder is as a server, the system can find and connect the video recorder.

HTTP

The admin user account can disable the HTTP service from the GUI or the web browser. After the HTTP is disabled, all the related services, including the ISAPI, Onvif and Gennetc, will terminate as well.

HTTP Authentication

If you need to enable the HTTP service, you can set the HTTP authentication to enhance the access security. Two authentication types are selectable, for security reasons, it is recommended to select digest as the authentication type.

IP Camera Occupation Detection

The function detects the network camera status. If the network camera has been added by another video recorder, the network camera status will show as □ in Online Device list.

1. Click Apply.
   1. Buzzer Switch

You can enable or disable buzzer with alarm linkage or exceptional linkage.

Steps

1. Click ® at the upper-right corner.
2. Click More.
3. Go to Buzzer Switch.
4. Turn on or turn off Enable.
   1. Device Maintenance
      1. Schedule Reboot

The device will automatically restart according to the schedule.

Steps

1. Click El at the upper-right corner.
2. Click More.
3. Go to Device Maintenance ^ Schedule Reboot .
4. Turn on Enable.
5. Set the reboot schedule.
6. Click Apply.
   • 1. Camera Upgrade

Upgrade the camera(s) in the added device list.

Steps

1. ClickMaintenance ( ) ^ More ^ Deice Maintenance ^ Camera Upgrade.
2. Click Check for Updates.
3. Upgrade camera.

• Select the channel to upgrade, and click the Upgrade on the right.
• Click Quick Upgrade to upgrade all channels that have updates.
  • 1. Device Status

You can mute the selected channel(s).

Steps

1. Click El at the upper-right corner.
2. Click More.
3. Go to Device Maintenance ^ Device Status .
4. In the Mute and Not Disturb column, check the corresponding channel(s).

Result

The selected channel(s) will be muted.

• 1. Upgrade

/»\ Warning

Do not shutdown or turn off the power during upgrade.

• • 1. Local Upgrade

Before You Start

Store the upgrade firmware to a backup device, and connect it to your device.

Steps

1. Go to Maintenance .
2. Click O near Firmware.
3. Select a backup device in Device Name.
4. Select the upgrade firmware.
5. Click Upgrade. Your device will reboot automatically.
   • 1. Online Upgrade

Upgrade the device with the latest online firmware.

Before You Start

Enable HiLookVision and configure its parameters. Refer to HiLookVision for details.

Steps

1. Go to Maintenance .
2. Click O .
3. Go to Online Upgrade .
4. Download the latest firmware.

Auto Download The will automatically check and download the latest firmware.

Test Upgrade Click Test Upgrade to manually check and download the latest firmware. 5. Upgrade your device if a new firmware version is available. The device will reboot automatically.

1. Alarm

When events occur, you can view their details in alarm center.

• 1. Set Event Hint

Select the events to hint in alarm center.

Steps

1. Click in the upper-right corner of local menu to enter alarm center.
2. Select Exception, Basic Event, or Smart Event to configure as your desire.

Figure 8-1 Alarm Centre

1. Click ft and select events to hint.
2. Click OK.

When the selected events occur, the alarm information will be displayed (locating in upper­right corner of local menu).

• 1. View Alarm in Alarm Center

Steps

1. Click in upper-right corner of local menu.
2. Select Exception, Basic Event, or Smart Event to view as your desire.
3. Web Operation
   1. Introduction

You can get access to the video recorder via web browser.

You may use one of the following listed web browsers: Internet Explorer 11.0, Apple Safari, Mozilla Firefox, and Google Chrome. The supported resolutions include 1024×768 and above.

For certain models, you will have to download a web component plug-in, and install it. Otherwise, a few functions would be unavailable. The download address is http://

hikdownload.ys7.com/web/webplugin/windows/WebComponents/standard/ WebComponents.exe .

• 1. Login

You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.

Steps

1. Open web browser, input the IP address of the video recorder and then press Enter.

C@Note

If you have changed HTTP port, enter http://IP address:HTTP port in address bar. E.g., http: 192.168.1.64:81.

1. Enter user name and password in the login interface.
2. Click Login.

Figure 9-1 Login

4. Follow the installation prompts to install the plug-in.

C@Note

You may have to close the web browser to finish the installation of the plug-in.

• 1. Live View

After login, live view interface shows.

Figure 9-2 Live View

• 1. Playback

Click Playback to enter playback interface.

Figure 9-3 Playback

• 1. Configuration

Click Configuration to enter configuration interface.

Figure 9-4 Configuration

• 1. Log

Steps

1. Go to Maintenance ^ System ^ Maintenance ^ Log .
2. Set the search conditions.
3. Click Search.

Figure 9-5 Log

1. Appendix
   1. Glossary

Dual-Stream

Dual-stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network. The two streams are generated by the DVR, with the main stream having a maximum resolution of 1080P and the sub-stream having a maximum resolution of CIF.

DVR

Acronym for Digital Video Recorder. A DVR is device that is able to accept video signals from analog cameras, compress the signal and store it on its hard drives.

HDD

Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters with magnetic surfaces.

DHCP

Dynamic Host Configuration Protocol (DHCP) is a network application protocol used by devices (DHCP clients) to obtain configuration information for operation in an Internet Protocol network.

HTTP

Acronym for Hypertext Transfer Protocol. A protocol to transfer hypertext request and information between servers and browsers over a network.

PPPoE

PPPoE, Point-to-Point Protocol over Ethernet, is a network protocol for encapsulating Point-to- Point Protocol (PPP) frames inside Ethernet frames. It is used mainly with ADSL services where individual users connect to the ADSL transceiver (modem) over Ethernet and in plain Metro Ethernet networks.

DDNS

Dynamic DNS is a method, protocol, or network service that provides the capability for a networked device, such as a router or computer system using the Internet Protocol Suite, to notify a domain name server to change, in real time (ad-hoc) the active DNS configuration of its configured hostnames, addresses or other information stored in DNS.

Hybrid DVR

A hybrid DVR is a combination of a DVR and NVR.

NTP

Acronym for Network Time Protocol. A protocol designed to synchronize the clocks of computers over a network.

NTSC

Acronym for National Television System Committee. NTSC is an analog television standard used in such countries as the United States and Japan. Each frame of an NTSC signal contains 525 scan lines at 60Hz.

NVR

Acronym for Network Video Recorder. An NVR can be a PC-based or embedded system used for centralized management and storage for IP cameras, IP Domes and other DVRs.

PAL

Acronym for Phase Alternating Line. PAL is also another video standard used in broadcast televisions systems in large parts of the world. PAL signal contains 625 scan lines at 50Hz.

PTZ

Acronym for Pan, Tilt, Zoom. PTZ cameras are motor driven systems that allow the camera to pan left and right, tilt up and down and zoom in and out.

USB

Acronym for Universal Serial Bus. USB is a plug-and-play serial bus standard to interface devices to a host computer.

Device Complete Guide

<p>The post Hilook 4K NVR Device Complete Guide first appeared on NVR IPCAMERA SECURITY.</p>

What is Hikvision AcuSense?

By minimizing false alarms triggered by animals, falling leaves, heavy rain, and other moving objects, AcuSense enables businesses and homeowners to focus security resources on real threats.Easy and affordable Artificial Intelligence has come to the mass market and a diverse set of users. Read on to learn more.

Hikvision AcuSense

Read More :

• How do I stop my Hikvision NVR from beeping?
• Hikvision Hik-Connect complete setup guide
• New Hikvision Hilook Firmwares 2022

INTRODUCTION

Demand Analysis

In traditional CCTV systems, all the moving objects in the picture will trigger the perimeter alarm, which may generate a lot of false alarms. Users have to waste a lot of time dealing with false alarms, and the alarm is unreliable. In addition, when the target needs to be found in the video, it needs to be manually searched by video playback, which is time consuming and laborious, and it is easy to lose key targets, which is very inconvenient.

After solving the basic monitoring and video problems, users need to receive more accurate alarms and to have a more convenient target search function to better use the monitoring system.

Solution

Some false alarms can be filtered by using a thermal camera, vibration optical fiber, radar, and other equipment. The cost of the whole system is too high, and it cannot meet the requirement of finding the target quickly afterwards.

With the development of artificial intelligence, target classification can be realized directly based on the video screen, and false alarm reductions and target retrieval can be provided, which can provide users with very cost-effective schemes.

System Architecture

Hikvision’s AcuSense Series of cameras and NVRs can prevent false alarms by identifying humans and vehicles when defining line crossing detection and triggering an alarm when only the selected object type (human and/or vehicle) is detected.

To set up False Alarm reductions and target classification without additional products, an AcuSense NVR and/or AcuSense cameras are required.

Figure 1, System Architecture Diagram

Function Description

Target Classification

By upgrading the hardware of conventional products, Hikvision has loaded artificial intelligence technology into the chip of the equipment. The equipment can classify and identify the objects appearing in the picture such as humans, vehicles, rainwater, light, leaves, animals, etc. Object classification is the basis for realizing false alarm and key target alarms.

Figure 2, Target Classification

False Alarm Reductions and Quick Target Search

Through target classification, alarms caused by animals, light, rain, leaves, or other objects can be filtered out, and only alarms triggered by human bodies and vehicles will be received. This is the function of a false alarm reduction.

In addition, in the face of a large number of monitoring video data, when searching key information such as people or cars, the target retrieval function is used. The device will record human body and vehicle information automatically, and solve the issue that video playback is time-consuming and easy to miss.

False Alarm Dy imhi

False Alarm by Rain

False Alarm by Animal

Figure 3, False Alarms

• False Alarm Reductions

* Quick Target Search

Human & vehicle targets detected efficiently.

The interference caused by other objeclsfanimal, leaf, light, rain, etc. f can be eliminated efficiently.

Human Target Search & Vehicle Target Search (supported by Hikvision AcuSense NVBs)

AcuSense Camera &

Main Functions

Figure 4, False Alarm Reductions and Quick Target Search

Configuring False Alarm Reductions

VISION

Live View

Playback

Picture

Configuration

Figure 5, Configuration > Event > Smart Event > Area Settings

1. Go to Configuration > Event > Smart Event > Line Crossing Detection in the local interface.
2. Use the pull-down list to select the camera to configure.
3. Check the Enable Local Smart Analysis checkbox to have the local NVR perform the smart analysis with a non-AcuSense camera. The NVR will acquire only the camera stream for intelligent event analysis, and the NVR will not acquire the camera’s smart event configuration. Up to four 8 MP non- AcuSense cameras are supported for false alarm reductions, and sub-stream resolution of these cameras have to be under WD1 (960*576). If this box is unchecked, the AcuSense camera (required in this case) will do the analysis. The NVR will acquire smart event configuration and alarm information from the camera.

NOTE: The NVR and camera configuration screens will slightly differ. This document uses the NVR configuration screens as examples.

1. Check the Enable Line Crossing Detection checkbox to activate line crossing detection.
2. Check one or both Detection Target checkboxes to set the type of object to trigger the alarm:

• Human: Alarm will be sent only if triggered by human(s).
• Vehicle: Alarm will be sent only if triggered by vehicle(s).
• No Box Checked: Alarm will be sent by any object(s).

1. Click the Area Settings tab.
2. Use the pull-down menu to set the line number to define (1-4). Up to four line crossing lines can be defined. The target classification can be set separately for each line.
3. Drag a line in the live view area with the left mouse button; release to end the line. Select line with left mouse button to move or resize the line.
4. Configure the line by clicking on one of the buttons:

• Max. Size*: Drag with the left mouse button to define a rectangle representing the maximum object size that will be detected crossing the defined line.
• Min. Size*: Drag with the left mouse button to define a rectangle representing the minimum object size that will be detected crossing the defined line.
• Draw Area: Drag with the left mouse button to define the total area to monitor.
• Clear: Click Clear, then click Save, to delete all line settings.

1. Use the pull-down menu to select the line crossing direction that will trigger the alarm:

• A<->B: Alarm will be triggered if object moves across the defined line from A side to B side or from B side to A side.
• A->B: Alarm will be triggered if object moves across the defined line from A side to B side.

Available only when configuring through the local NVR; setting will not appear if configuring through the camera.

• B->A: Alarm will be triggered if object moves across the defined line from B side to A side.

1. Set line crossing Sensitivity (0-100). The sensitivity value = 100 – S1/ST x 100, where S1 is the area of the target that has crossed the line and ST is the actual area of the target. The higher the sensitivity, the easier it is to trigger the alarm.
2. Click Save to save the line crossing settings.
3. Repeat for additional lines, up to four total.
4. Click Save.

Configuring Arming Schedule

Figure 6, Arming Schedule

1. Click the Arming Schedule tab to display the Arming Schedule section.
2. Drag the left mouse button to draw/modify blue timelines to define the times and days that the defined alarm will be active. The line may be resized and/or re-positioned using the mouse.

NOTE: Click X Delete to delete a highlighted blue timeline.

Click the HU Delete All to delete all of the defined blue timelines.

1. Click Save to save the schedule settings.

Configuring Linkage Method

Figure 7, Linkage Method

1. Click the Linkage Method tab to display the Linkage section.
2. Check the alarm action checkboxes you wish to configure:

• Normal Linkage

• Send Email – An alarm will cause the system to send an e-mail notification to the pre­defined e-mail address.
• Notify Surveillance Center – An alarm will cause notification to be sent to the pre-defined Surveillance Center.
• Upload to FTP/Memory Card – An alarm will cause the system to upload a notification to a pre-defined FTP site or memory card.
• White Light Flashing (Strobe Light and Audio Alarm/SL models only) – An alarm will cause the camera’s white light to flash (strobe).
• Audible Warning (Strobe Light and Audio Alarm/SL models only) – An alarm will cause the system to generate an audible alarm.

• Trigger Recording^[1]

• A1 – An alarm will cause this camera to start recording.

1. Click Save to save the alarm action settings.

Configuring White Light Output (Strobe Light and Audio Alarm/SL Model Only)

1. Go to Configuration > Event > Basic Event > White Light Alarm Output.
2. Set Flashing Duration from 1 to 60 seconds.
3. Set Flashing Frequency to High (interval 0.6 seconds), Medium (interval 1 second), or Low (interval 1.5 seconds).
4. Click Save to save the settings.

Figure 8, White Light Alarm Output

Configuring Audible Alarm Output (Strobe Light and Audio Alarm/SL Model Only)

Figure 9, Audible Alarm Output

1. Go to Configuration > Event > Basic Event > Audible Alarm Output.
2. Set Alarm Sound Type – Click the drop-down list to select one of 10 types of built-in alarm sounds.

NOTE: Importing local audio files is not supported.

Details of 10 Types Built-in Alarm Sounds

Figure 10, Alarm Sound Type Pull-Down List

1. Set Alarm Times – Enter how many times the alarm sound will repeat, from 1 to 50 times
2. Set Sound Volume – Volume can be set from 1 (softest) to 100 (loudest).

Checking Alarms

Use the Web interface to check the defined alarms.

Figure 11, Line Crossing Detection (Target: Vehicle)

1. Perform the following steps to show the defined lines and draw area overlaid on the image.

A Go to Configuration > Local > Rules.

2 Check the Enable checkbox.

Figure 12, Enable Target Rule Box

1. Check the alarm on the network camera’s Web preview interface. When someone crosses the line, the perimeter box and line crossing lines turn red.

Figure 13, Human Triggers Line Crossing Detection Alarm

Figure 14, iVMS-4200 Filter Human Alarm

NOTE: The rule box displayed in the network camera Web preview interface does not make target classification judgments; the alarm information is subject to the search result received from the alarm receiver and NVR. A comparison of the Web interface with the alarm receiver (such as iVMS-4200 client) can be used to distinguish if false alarm reductions has been performed.

Quick Target Searching

NVR Search Capabilities

File Management Search

1. On an AcuSense I-Series NVR, go to File Management.
2. Highlight Human Files or Vehicle Files.
3. Time: Set the time frame you wish to search.
4. Camera: Set the camera you wish to search.

5. File Type: Set file type you wish to search, Videos or Pictures.

For DS-9664N/-/8 local interface, file type must be specified with search conditions.

NOTE: AcuSense NVRs can switch between picture and video on the search results page without having to perform the search again.

6. Set the search choices:

• Select the target image in the red box area on the upper left corner, and listed picture will be a close-up view of the target.
• Select the source image in the red box area on the upper left corner, and listed picture will be the original picture.
• Select video in the red box on the upper right corner, and listed files will all be video files.
• Select picture in the red box on the upper right corner, and listed files will all be picture files.
• Select All, and the images and videos will be displayed together.

İDS-7732NXI-I4/16P/4S Local Interface

File type can be actively switched using the options located at the top right. Both picture and video results can also be listed together by using the All option.

Smart Search

AcuSense NVRs support smart search for Human Body Detection and Vehicle Search. Picture and video is combined on the search results preview screen.

IDS-7732NXI-I4/16P/4S Local Interface

NOTE: I-Series NVRs do not support smart search for human and/or vehicle target filtering.

DS-9664NI-I8 L ocal Interface

False Alarms Search

AcuSense NVRs can display all false alarms by using the All Files search (set event type to “False Alarm”). False alarms are generated by objects that approach being mistaken for a human or vehicle.

Figure 15, False Alarms

iVMS-4200 Client

Figure 16, Add Network Camera

Adding a Network Camera

1. Add the camera in the iVMS-4200 Device Management section.

Figure 17, iVMS-4200 View Alarm Information (Human)

1. View the triggered alarm on the iVMS-4200 Alarm Event interface. Alarm detail information will be labeled Human or Vehicle, as shown in the figure below.

Figure 18, iVMS-4200 View Alarm Information (Vehicle)

NOTE: The Target Type shown on the iVMS-4200 is the same as the Detection Type set in the configuration interface. Alarm information triggered by the unchecked category will be filtered and will not be displayed on the iVMS-4200.

1) Set Detection Type to Human, then the iVMS-4200 will display only Human target type alarm information.

2 Set Detection Type to Vehicle, then the iVMS-4200 will display only Vehicle target type alarm information.

Viewing Alarm on GUI Interface

The NVR’s local GUI interface cannot classify Humans and Vehicles in this version.

The current mechanism: after checking Smart Detection, the GUI interface will display all alarm pictures without classification between humans and vehicles (this feature will be optimized by the end of the year).

Figure 19, NVR local GUI interface

Viewing Alarms on iVMS-4200

1. Add the NVR on the iVMS-4200 Device Management interface.

Figure 20, Add NVR on iVMS-4200

Figure 21, View Alarm Information on iVMS-4200 (Human)

2. View the triggered alarm on the iVMS-4200 Alarm Event interface. Alarm detail information will label the target category as Human or Vehicle, as shown in the figure below.

Figure 22, View Alarm Information on iVMS-4200 (Vehicle)

The NVR alarm upload via iVMS-4200 is the same as for a network camera. The Target Type shown on the iVMS-4200 is consistent with the Detection Type set on the configuration interface. Unchecked categories will be filtered out and will not be displayed on the iVMS-4200.

Known Issue

When adding network cameras to the NVR, the NVR will issue a 24-hour arming schedule to the camera by default. After the camera is connected, configuring an arming schedule on the NVR will affect only whether the alarm is reported and displayed on this NVR, but the camera setting time will not change. If other terminals access the camera, the alarm will still be received.

Product List

Installation Requirements

• The proposal altitude of installation distance is 3 to 5 meters, equipment bow angle is approximately 10°, specific adjustments are according to the environment.
• The maximum monitoring distance depends on the lens’ focal length. The table of the maximum monitoring distance for the specific focal length is as follows:

• The monitoring area cannot be covered by nearby objects. Do not shoot backlight at the installation position, which will affect the image effect. The following shows a perimeter environment installation:

Figure 23, Installation of the Perimeter Environment

• The equipment installation needs to pay attention to certain blind areas. The calculation method of blind area distance is as follows:

Height

Horizontal Line

Depression Angle

H

D —» * Monitor Distances

• D = H • tan(90° – a/2 – p)
• D: Camera monitoring blind area H: Mounting height
• a: Vertical field Angle p Angle of depression

• Recommended Scenario:

• Try to avoid getting too close. It is recommended that the target be more than three meters away from the camera. For example, avoid scenes with lots of trees nearby.
• If there is a mirror in the environment, the mirror image or shadow can easily lead to false alarm

triggering.

• Adjust the camera angle during installation to avoid interference from high brightness lights or headlights.
• Domes are not recommended for outdoor scenes, IR reflect can seriously affect the accuracy of the alarm, as shown below:

– Heavy traffic scenes such as station, airport, theater, etc., will generate a lot of perimeter alarms, so it is suggested to avoid these types of scenes.

– Avoid situations where personnel targets are too large. AcuSense NVRs can analyze target sizes between 1/16 and 1/2 of the image’s vertical size. For example, if the camera’s resolution is 1080p, the vertical size of the target should be between 64 and 540 pixels.

In the following scene, the target takes up almost the whole picture. Adjusting the camera angle so that a targets is detected from a far distance so that it appears a suitable size is suggested.

Using Region Entrance/Exiting Detection instead of Intrusion/Line Crossing Detection is recommended for region intrusion of fixed scenarios.

1. Available alarm outputs will vary by NVR and camera. ↑

<p>The post Hikvision AcuSense NVR User Manual first appeared on NVR IPCAMERA SECURITY.</p>

Introduction of 5G AI Camera
Milesight 5G AI Pro Bullet Plus Network Camera is our newest member of the 5G Series. Featuring cutting-edge 5G technology, the 5G AI Pro Bullet Plus Network Camera provides a fresh experience of UHD image quality, low latency and fast transmission speed to some scenarios where network wiring is inconvenient. Offering AI deep learning, compact structure and more, Milesight 5G AI Pro Bullet Plus Network Camera builds a whole new world by combining high-tech with high-performance.

This article will introduce the basic configuration of 5G AI Camera, so that you can quickly learn to use our 5G AI Camera.

Read Next : How to use VPN on Milesight Network Camera

Note: For more information about how to set IoT, please refer to Milesight-Troubleshooting-AIoT Camera

2．How to Use 5G AI Camer

1) How to Connect 5G AI Camera

1. If you need to use the 5G network, you can use a SIM card to connect to Cellular for your camera.

Note: 

1) As long as the SIM card is inserted and cellular is enabled, it will consume the data of the SIM card. If there is live video streaming, it will consume more data.

2) 5G AI Camera support 5G, 4G and 3G networks.

2. If you don’t need to use the 5G network, you can connect to the camera through LAN. And PoE are supported for 5G AI Camera.

3. After completing the basic settings of 5G AI Camera, you can access the camera through the Milesight P2P or VPN using 5G network without connecting the network cable.

Note: 

1) If you use the 5G camera for the first time, it is necessary to connect the camera through the network port to access the web page of the camera for basic configurations.

2) For Milesight CMS, M-Sight Pro and Milesight VMS Enterprise, we recommend to add 5G AI Camera through P2P when using 5G networks, which is more convenient and simple.

3) What’s P2P?

P2P technology is convenient, simple, stable and reliable. It does not require a fixed IP address, and the connection of camera through MAC address won’t change because of the network environment. P2P technology is very convenient and practical for the wireless network transmission of 5G AI Camera.

4. Coming Soon: 5G AI Camera can be added and managed on Milesight back-end or Third-party via VPN.

2) Easy Deployment and Compact Structure of 5G AI Camera

3．Compatibility with Milesight Back-end

1) Accessing from Milesight Back-end Software

About Milesight Back-end Software:

² Milesight CMS is a central management system for Milesight cameras and Milesight NVR. It is mainly used to manage and configure multiple devices. With high-efficient management performance, Milesight CMS software offers users a superior administration experience in such centralized system.

² Milesight VMS Enterprise is a professional and intelligent video management software for medium-to-large business projects. Together with Milesight cameras and third-party cameras, it can simplify your video surveillance and fulfill your demands and expectations with rich core functions including Live View, Playback, Recording Export, E-Map, Event Alarm, Smart Search, Al Analytics, and more.

² Milesight M-Sight Pro, a security camera app both for iOS and android, enhances security by providing administrators the flexibility to monitor the the live video from network cameras and NVRs via wireless network.

Note: 

1) For Milesight NVR, it does not support adding or managing 5G camera when using 5G network.

2) Videos from the SD card of the 5G camera can be viewed on the Milesight CMS and M-Sight Pro.

3) VMS Enterprise supports recording surveillance video from 5G cameras to the VMS system.

① Milesight CMS

For Milesight CMS, it supports adding 5G camera via P2P using 5G network, and then the parameter of 5G can be configured.

Step 1: After logging into the Milesight CMS, go to “Management“→ “Devices“→ “Add Devide Manually“, and you can add 5G AI Camera by Mac Address when selecting P2P connection type.

Step 2: Go to “Devices Config“ → “5G Camera“ → “System“ → “Network“ → “Cellular“, You can set the cellular settings and check the cellular status and on CMS as shown below.

② Milesight VMS Enterprise

For Milesight VMS Enterprise, it supports adding 5G camera via P2P using 5G network.

Step 1: After logging into the Milesight VMS Enterprise, go to “Settings“→ “Devices Management“→ “Add Device“→ “Add Manually“, and you can add 5G AI Camera by Mac Address when selecting P2P protocol.

Note: VMS Enterprise does not support 5G and IoT configuration currently.

③ M-Sight Pro

For M-sight Pro APP, it supports adding 5G camera via P2P using 5G network.

Step 1: After logging into the M-Sight Pro, go to “Device Manager“→ “Add Camera“, and you can add 5G AI Camera by Mac Address when selecting P2P protocol. Or you can connect the 5G AI Camera by P2P QR Code.

Note: The P2P QR Code of the 5G AI Camera is activated on the camera Web by default.

4．How to Configure 5G AI Camera

Step 1: Insert the SIM card into the SIM card slot at the bottom of the camera, as shown below:

Note:

① It supports Nano SIM for SIM card slot.

② For 5G camera, the SD card slot is inside the camera, as shown below:

Step 2: After logging into the web, go to “Settings“→ “Network“→ “Basic“→ “Cellular“, you can check the cellular status and set the cellular settings here, as shown below.

Step3: Fill in the information provided by your Internet Service Provider (ISP) to Cellular Settings interface, then click “Save” to access the network successfully.

Note: 

①For some Internet Service Providers, users can access the 5G network by simply inserting the SIM card directly, without additional configuration.

②As long as the SIM card is inserted and cellular is enabled, it will consume the data of the SIM card. If there is live video streaming, it will consume more data.

Please refer to the meaning of the options as follows：

Step4: After connecting to the network successfully, you can check the cellular status information on Cellular Status interface, as shown below.

Please refer to the meaning of the options as follows：

Step 5: Set the schedule, the 5G network will take effect according to the schedule you set.

Step 6: After configuring the cellular settings, you also need to complete other basic configurations of the camera if needed, such as events, recordings, etc.

Note: About How to configure other function, please refer to Milesight Network Camera User Manual.

Step 7: After completing the basic settings of the camera, you can access the camera using 5G network without connecting the network cable.

<p>The post How to Use 5G AI Camera first appeared on NVR IPCAMERA SECURITY.</p>

How to set presets & auto-patrol for xmartO PTZ cameras?

The xmartO WT series, DZ series and DPM series PTZ cameras support up to 8 preset points.

Definition of ‘presets’: PTZ cameras can be navigated to view different areas. Presets record the key points so you can reach the recorded poinits with one tap.

Auto-patrol: a feature xmartO developped based on preset feature. The camera patrol the preset points back and forth. AKA auto-cruise, auto-scan.

1. Set preset points

While viewing the camera, tap PTZ icon to enter PTZ menu; then tap Preset to enter preset menu. Use the joystick to navigate the camera to the 1st point, tap ‘Add Preset’ to save the point 1; then navigate the camera to next point and tap ‘Add preset’ to save the point 2…you can save up to 8 points.

2. In the preset menu, you can tap ‘Go to‘ to reach the preset points.

3. Start Auto-patrol

a) If your camera does not have optical zoom, tap the image, on right you will see the A icon. Tap the A icon the camera will start to patrol the preset points.

b) If your camera is the version with optical zoom, well it has higher level chipset inside. The Auto-patrol is a bit different. In preset menu, tap ‘Shortcut mode’, type in ’13’ and tap Go to, the camera will start to patrol the preset points.

4. Stop Auto-patrol

Tap any of the direction on the joystick will stop the auto patrol.

Tips: cameras added to xmartO NVR have the same steps. It’s similar to on the NVR. Only the NVR’s UI is a bit different and the A icon is in the middle of the joystick. 

Read Next : How to Set up Alexa for Blink devices

View XMARTO WiFi cameras on PC

CMS is called Camera Monitor System. It is a camera monitoring client for online preview image, video storage, remote playback, device management, video/screen download and other functions. It is suitable for DVR, NVR, IPC, VR CAM, Wifi IPC and other devices.

Below are the basic instructions of using CMS on your computer. If you need detailed user manual of CMS, you can download it from our website: https://xmarto.com/pages/download

Also, you can click More Function-System Message-Open the manual to find more details of xmartO WallPixel CMS.

1. Download xmartO WallPixel CMS Software
Link: https://www.xmarto.com/downloads/

2.Installation and operation  

Step 1: Run the xmartO_WallPixel_for_PC_Setup.exe installation package.

Step 2: Select the language that your system needs to use.

Step 3: Read and accept the agreement.

Step 4: Select and determine your software installation path.

Step 5: After the installation is successful, immediately run and use.

 

3. Login

3.1 Local Login

Default username: admin
Default password: no password, leave it blank

For security reason, we suggest you set a password after you are logged in.

3.2 Cloud Login

Use the app account: Enter the username + password of the app account on the cloud login interface to log in.

Register an account:Click on the registered account in the cloud login interface, enter the mobile phone number / email (if using the mobile phone number to register, you need to add the mobile phone number area code), click OK, enter the password and verification code and click Register now, after verification, you can complete the registration.

Forgot password:Click on the forgot password in the login interface, enter the registered account to obtain the verification code, enter the verification code and the new password and click OK to reset the password.

 

4. Add Device to CMS

You can add devices to the CMS in two ways:

Method 1: After adding the device using the mobile APP, directly log in to the CMS using the APP account password, and you can view the device you have added in the CMS system;

Method 2: Please make sure that your device is equipped with a network or a network cable, log in to the CMS, and click the add button in the upper right corner.

Add IP / DDNS: manually enter the device “IP / DDNS + port + channel number + device password”, select “type” according to the actual situation of the device, the rest of the information remains the default, click Finish to add successfully.

Cloud ID addition: manually enter the device “cloud ID number + channel number + device password”, select “type” according to the actual situation of the device, the rest of the information remains the default, click Finish to add successfully.

 

 

LAN search device addition: select the device management in the function bar below the system, click the interface refresh button, wait for the device to be searched, check the required device and click add (enter the device IP / ID to quickly find the need to add device)

5. Live View
The xmartO WallPixel  CMS allows you to view cameras on your computer both locally and remotely.

5.1 Main Menu Introduction of CMS:

• Playback: Click to playback videos stored in your hard drive
• Device Management: Manage your device(s)
• User Parameter: Some basic settings of CMS
• Record: Record short videos of live view cameras, videos will be stored to your computer
• Screenshot: Take snapshots of live view cameras, pictures will be stored to your computer
• Disconnect All: Turn off live view of all cameras on CMS
• Screen Number: Choose how many cameras you want to display on one screen, the CMS allows you to view up to 64 cameras simultaneously
• More Function: More basic functions of CMS, including creating user, setting password and etc.

5.2 Multi-channel Viewing
CMS allows you to view up to 64 cameras simultaneouly. So if you have multiple systems, you can view all cameras in multiple systems simultaneously on this CMS.

5.3 Record and Snapshot
CMS allows you to record short videos and take snapshots when live view cameras, videos and snapshots will be saved in your computer. You can change the storage path here as shown in the picture.

 

6. Playback
CMS allows you to playback your history videos stored in hard drive. With this CMS, you can playback videos stored in hard drive or micro SD card from all over the world. Detailed instruction as below:

a. Click “Playback” on bottom navigation, it will pop out message “Close the video being played?” Choose Yes.
b. Select a window on left(1), select a channel from the device(2), choose the Record Type, select a date(3), and click “Retrieval”(4). The CMS will start playback videos of that channel immediately. Move the cursor on the time bar at bottom to locate an exact time to replay the camera per your needs.

c. You can record short videos or take snapshots while playback videos. Videos and snapshots will be stored to your computer.

 

7. Backup 
CMS allows you to download and backup videos to your computer.
The downloaded video files are in .mp4 format, you can playback with any player.

Detailed instruction here:
Click “Playback” on bottom navigation, select a device channel, choose Record type, select a date and then click “Download” on bottom right. You’ll see below interface with a list of all recorded videos.

 

Videos will be saved to your computer, as shown in below picture. You can also change the storage path.

 

8. User Management

8.1 Change admin password
Click “More Function” on bottom navigation, choose “System Message” and click “Change Password”. Keep the old password blank, and enter your new password, confirm your new password, and click “Confirm” to save it.

 

Something important need to pay attention to:
If you have once installed old ESeeCloud version on your computer and plan to upgrade to this new one, you need to uninstall the old version from your computer completely, and delete related files. Then install this new version, otherwise the new one does not work on your computer.

Here is how to uninstall the old one and delete the related files from your computer:
1. Uninstall the current ESeeCloud software from your computer.
2. Go to the place where you install this software on your computer and delete the file named with ESeeCloud completely, usually it is stored here:  C:\Program Files (x86)\EseeCloud
3. Go to below path and delete the ESeeCloud file, as shown in below picture.
C:\Users\Administrator (or your username)\AppData\Local\EseeCloud
C:\Users\Administrator (or your username)\AppData\Local\EseeCloud_Data
C:\Users\Administrator (or your username)\AppData\Roaming\EseeCloud

If the file is not shown there, then you need to check “show hidden files, folders and drives “, as shown in below picture.

How to view xmartO cameras on Mac?

EseeCloud is an updated CMS to preview, playback and backup the xmartO cameras/ camera systems on Mac.

1. Download ESeeCloud CMS Software
Download the EseeCloud CMS from xmartO website:
https://www.xmarto.com/downloads

2. Install and run ESeeCloud CMS on your Mac.
Install the CMS on your Mac and run it. If you have problem installing ESeeCloud CMS to your Mac, please refer to,

https://support.xmarto.com/?action=faq&cat=1&id=20&artlang=en

3. Login ESeeCloud
After that, you will be asked to type in the username and password. The default username is “admin”, default password is blank. For security reason, please set a login password to prevent unauthorized access.

4. Add Device to ESeeCloud CMS

4.1 Auto add, applies to add devices in LAN
EseeCloud CMS will search the devices in LAN automatically and display them in the Device Management list.

a. Click “Device Management” in upper navigation, you’ll see your device(s) listed there.
b. Select the device(s) and click Add. Your device(s) will be added to ESeeCloud CMS. They will show on upper right.

 

c. Go back to Live View, and click on the “play button”

behind each device to preview. If you want to view cameras from all devices at the same time, simply click “All Connect” at the right bottom. Click on the “stop button” behind each device to stop previewing cameras of this device.

4.2 Manual add, applies to add devices remotely
If you want to view cameras from a remote computer, you need to add the device to your ESeeCloud CMS manually on that computer.

a. Run and login ESeeCloud, then click “+” at top right corner. Or click “Device Management” on upper navigation.

b. You’ll see below interface. There are two ways to add device to ESeeCloud: Add cloud ID and Add IP/DDNS.
Add cloud ID: Add device to ESeeCloud with your NVR’s Device/Cloud ID. It is available for local and remote access.
Add IP/DDNS: Add device to ESeeCloud with your NVR’s IP address. It is available for local access only, so if you want remote access your cameras on this computer, choose the first Add cloud ID.

c. Type in the information required and click “Add”, the device is added to this ESeeCloud CMS, you can preview the cameras now.

Note: If you are adding xmartO VR camera, please turn on the Panorama.

5. Live View
5.1 The ESeeCloud CMS allows you to view cameras on your computer both locally and remotely. Please refer to below image for basic introduction of buttons.

5.2 It allows you to view up to 64 cameras simultaneously.

5.3 It supports all xmartO security camera systems and VR cameras. You can turn on panorama for VR cameras here, and also you can turn on the auto cruise.

6. Playback
The ESeeCloud CMS allows you to playback your camera videos. With this CMS, you can playback videos stored in hard drive or microSD card from all over the world. Detailed instruction as below:

a. Click “Playback” on upper navigation.
b. Select a window on left(1), select a channel from the device(2), choose the type(3), and select a date(4), click “Search”(5). The CMS will start playback videos on camera windows shortly. Move the cursor on the time bar at bottom to locate an exact time to replay the camera per your needs.

Note: The ESeeCloud CMS allows you to playback 4 cameras at the same time.

7. Backup (It works in LAN network only)
The ESeeCloud CMS allows you to download and backup videos to your computer.
The recorded video files are in .avi format, you can playback with any player.

Detailed instruction here:
Click “Resource Management” on upper navigation, then select the channel you want to back up, select the type and date, click “Search”, you will see the recordings on the left. Click the “Download” icon to download the videos you want. Videos will be saved to your computer.

Videos will be saved to below path in default:

/Users/macusername/cms_data/cms_video_download/

You can change the storage path here:
Click the setting icon at upper right corner, then you’ll see below box. Click the three dots to change the storage path, and click Confirm.

8. User Management
8.1 Change admin password
The ESeeCloud CMS’s default username is admin, and default password in blank, means no password. For security consideration, we suggest you set a password for CMS after logged in. Here is how:

Click the “human” icon at upper right corner, then click Change Password. Keep the old password blank, and enter your new password, confirm your new password, and click Confirm.

 

8.2 Add new user
You can add new user for ESeeCloud CMS, here is how:
Click User Management on upper navigation, then click New, you’ll see below box.
Enter a username and remark name, click Confirm. (Remark name here is your nick name.)

Note: When you create a new user, you are not asked to enter new password for this user. It uses default password blank. You can change the password after logged in.

How to view cameras on the mobile app (WallPixel)

1. Download and install WallPixel App

Download the free WallPixel mobile app from App Store or Google Play Store and install the application on your phone or tablet.

          WallPixel HD

2. Creating an Account                                                                                                   

Tap the app, click “Register”, enter the required information to create an app account.
If you already have an account, login with your username and password.

After click “Register”, input your phone number or email address then the app will send you the verification code.

Check the email or text you’ve received and input the verification code.

Then you need to set a password and confirm it again. (The password should be a combination of 6-20 numbers or letters.)

At last, click “OK”,you’ll create the account successfully.

3. Adding NVR Device to App

Tap “+” at the top right corner, then tap the first option ” Wifi Camera Kit with NVR” to add your NVR device to the app.

4. Entering Device Information

Enter the required device information and click Save.

Cloud ID: This is your system’s Device ID, which can be found at the right bottom of your monitor. It is 9 digits. (NVR Device ID can also be found at NVR’s System setting – Network setting)
Username: Your NVR login username, default is admin. If you’ve set a new user for your NVR, use the new username here.
Password: Your NVR login password, default is empty, means no password, leave it blank. If you’ve set a new password for your NVR, make sure to type in the new password here.

* You can also scan to add your NVR device to the app.
a. Right click your NVR mouse, then click System setting – Network setting, click “Show QR Code”. The Cloud ID QR Code will be displayed.
b. Open the app, click + at upper right corner, then choose Scan and scan the QR Code displayed in your NVR’s network setting interface.
c. Enter your NVR’s login username and password, save the settings. Your device is now added to app. You can start live view cameras now.

5. Viewing Cameras on Phone

Once you click “Save”, the device will be added to your account and you’ll be directed to the device list page. As shown in below picture. Click the device to start live viewing your cameras.

6.View live video on mobile

Playback: You can playback the recorded videos in HDD on your mobile. Select any channel and click playback to review recorded videos of that channel.

Window: You can choose to view 1/4/6/8 cameras at a time.

Aspect Ratio:You can adjust the aspect ratio of the cameras’ image.

SD: Change live view resolution. You can select from HD or SD. HD means high definition resolution, while SD means standard resolution.

7.My account info.

Personal info: View your account information and change the password.
App setting: Some basic settings for your app.
Version: Your current app version.
Logout: Log out your current account.

How to view xmartO cameras on Alexa Echo Show?

Now all of our xmartO products can work with Alexa.

Pls see the details in the following link to view your cameras on Alexa Echo Show:

https://m.media-amazon.com/images/S/aplus-media/sc/37fa1474-c687-4fdf-af21-76a8b73f4b28.pdf

How to set camera’s light mode on the NVR? (solves black night vision)

The light mode of each camera lets you select which lights to use.

Click the camera image, it will pop-out a quick menu on bottom, pls click Color & Light-Light Model.

Infrared mode: uses IR LEDs only. At night you see B&W night vision. And the camera will then automatically adjust the day & night vision.

full color mode: flood lights stay on at night, you see color night vision.(Only cameras with floodlight can do it)

smart mode: B&W IR night vision when nobody detected, flood lights automatically turn on when people detected.

How to Upgrade xmartO IP camera firmware

OTA upgrade cameras firmware from APP (for standalone cameras)

1. For standalone cameras, in the APP device list, tap “…” at upper right corner of your device, choose “Settings”. It will show a red dot if there is a newer version.
2. Tap the red dot to upgrade your camera from OTA server.

It will take a few minutes to update your camera; and the update requires your camera to have good Internet connection.

Upgrade camera firmware from NVR

For multiple-camera systems, if you want to upgrade the cameras, you will need to do it from the NVR menu with an USB stick.

1. Please download the camera’s new firmware from xmarto.com or contact customer support for new firmware

2. Copy the firmware to an USB flash disk’s root directory (not in any folder)

3. Plug the USB flash disk to your NVR’s USB port

4. Go to System setting-CH Setting- IPC Maintenance, choose the firmware from USB Storage, and click start to update the firmware of your camera.

The camera will be uprgraded and you will see a new version.

Tips: if your NVR has only 1 USB port, click Start, the NVR will start a 60-second count down. Within 60 seconds, unplug the mouse and plug the USB flash drive, your camera will be upgraded. 

How to enhance WiFi connection between cameras and NVR?

While using XMARTO WiFi security camera system, customers may experience video freeze, video lag or even “no video” issue.

This is typically caused by weak WiFi signal from cameras to the NVR.

Based on 2.4Ghz WiFi, all cameras connect to the NVR’s own WiFi, just like your phones/ tablets connect to your home WiFi router.

In line of sight, XMARTO WiFi cameras can be mounted 1000ft (300m) away from the NVR. The camera system handles distance very well.

However, like any WiFi devices, the cameras do not handle obstacles very well. Each wall reduces its WiFi strength noticeably.

How Obstacles Affect Your Signal Strength

When your wireless signal is transmitted through various materials, such as walls and windows, the signal strength is affected. Though the NVR and wireless camera may be very close in proximity, you could still notice high signal interference if the signal passes through certain obstacles. For instance, if the signal passes through a concrete wall it will be severely weakened. Please reference the below chart to see which obstacles highly affect your signal and which do not.

Based on the facts, below are some suggestions of how to optimize your cameras’ WiFi connection.

1. Select a WiFi channel with least interference for your NVR

As the only hub, the NVR’s WiFi performance is crucial. To select a least-interfered WiFi channel for the NVR, ensures its performance not affected by other WiFi devices.

This is how to,

A) In NVR’s System setting – Network setting – WiFi setting. Click “Auto Select Channel“, the NVR will automatically select a WiFi channel with least WiFi interference.

B) For Japanese customers, you can choose region MKK and channel “Other” (channel 14) to avoid some WiFi interference.

2. Place your NVR and cameras reasonably

The NVR is the only WiFi hub, all cameras are WiFi devices that need to connect to the hub. Centralize the position of the NVR so it reaches all cameras well.

Principle of placing NVR and cameras: avoid any possibly avoidable wall, in the line from NVR to cameras.  

Do not place near high voltage wires or other sources of electrical interference. Electrical interference will degrade the quality of the signal.

Below are some more tips:

 

 

If there has to be obstacles between the NVR and camera, adjust the height of camera or NVR to avoid floor. Floors are normally heavier than walls.

Always find possible open between NVR and camera, mount camera and place NVR’s spot accordingly to allow signal to pass.

Metal walls (including metal garage gate) absorb wifi signal. Use extra extendable wifi antenna to bring camera’s antenna inside the wall. This also works for heavy concrete wall.

Try to keep camera and NVR’s antennas parallel to get better signal pick-up.

3. Bring the camera’s antenna through a wall

If a camera needs to be mounted behind a wall, you may use a WiFi antenna with extension cable to pass the wall.

Search “WiFi antenna with extension cable” on retail website like Amazon, you will find a lot of options.

Mount the camera behind the wall, drill a hole, wire through the hole to bring the antenna inside the wall.

4. Take advantage of XMARTO Dream Liner WiFi Relay technology
The xmartO Dream Liner technology uses cameras in middle as repeaters. That way, further cameras connect to closer cameras 1st, and then to the NVR as a group.

The latest G3 XMARTO WiFi camera systems do it automatically.

WiFi Relay

G3 Auto WiFi Relay

Here is an article about WiFi Relay,

https://support.xmarto.com/index.php?action=artikel&cat=1&id=32&artlang=en

5. Use a WiFi camera repeater

Add an RPT20 physical WiFi camera repeater for that camera,

6. Hard Wire Cameras
If you cannot get a camera to work via WiFi anyway, you should consider to hard wire that camera, especially when it’s PTZ camera.

Here is how to hard wire a camera,

https://support.xmarto.com/?action=faq&cat=1&id=50&artlang=en

How to pair a camera to an XMARTO NVR?

After you purchased an extra add-on camera, or when you want to swap a certain camera, you need to pair the new camera to your NVR.

1. Add by WiFi (for most cameras)

XMARTO’s “Add Cam by WiFi” feature makes this super easy.

1. Bring the camera close to the NVR, plug it to power.

2. On NVR screen, right click to enter main menu > Add Cam by WiFi. The NVR will search and add the new camera(s). Done.

The new camera will be added to NVR channel within a miniute.

What if: If this does not work, hold the camera’s reset button 6 – 10 seconds to bring the camera into config mode. Run “Add Cam by WiFi” on NVR.

 

2. Add with Ethernet cable (for cameras without reset key)

 Another way: pair the camera with an Ethernet Cable.

1.Plug the new camera to power. Use an ethernet cable to hardwire the camera to your NVR’s LAN port.

2. On NVR screen, right click to enter NVR’s main menu > Camera Manage.

3. In upper box, click “Refresh” button to search the camera out. The camera will be listed out an initial IP address 192.168.1.xxx

4. Click to select the camera, then click in below box to select an empty channel.

5. Click “Match Code“. The system will start to pair the camera to NVR’s WiFi.

6. Within a minute or so, the camera will be successfully paired to channel and displays image. You can now unplug the camera and mount it to where you want.

How to set a closer camera as a WiFi repeater for a camera that is out of WiFi range?

Start from Generation 3 (NVR and camera with ver.3.0+), XMARTO WiFi camera systems come with AUTO WiFi Relay.

AUTO WiFi Relay: when a camera is having weak WiFi signal. It shall come in and out frequently. Such a camera will AUTOMATICALLY find a close-by camera as WiFi repeater, connect to that camera, thus to relay back to the NVR.

First of all, to get good WiFi connection for cameras, you should decide your NVR’s location and WiFi channel well.

1. Centralize your NVR location so it reaches all cameras well.

2. Use a WiFi channel with least WiFi interference, here is how,

A) In NVR’s System setting – Network setting – WiFi setting. Click “Auto Select Channel“, the NVR will automatically select a WiFi channel with least WiFi interference.

Dream Liner Auto WiFi Relay

Q1: How do I know whether the Auto WiFi Relay is on?

A1: It’s set on by default. Right click to enter NVR main menu – WiFi Relay, you can see the status.Make sure Auto WiFi Relay is checked.

Q2: How can I take advantage of AUTO WiFi Relay?

A2: Since it’s an auto feature now, you don’t need to do much setting job.

Here is our suggestions:

Before mounting your cameras, simply place all cameras where you want, plug them to power, wait up to an hour to see whether all cameras can stream smoothly to the NVR. If they do, mount them; if they don’t, adjust the location of your NVR, or a certain camera, till you get a stable connection for all cameras, then mount them.

When you do the test run, most cameras shall be able to connect directly to the NVR. A certain camera that is far, or with more obstables may have weak WiFi signal to connect to the NVR. It may come in and out. When it’s coming in & out, it trys connecting to the NVR as always. If it feels hard to connect, it will find an alternative – a middle camera as repeater.

This is an algorithm, it may take up to 30 minutes for the camera to form a relay chain; and suprisingly you may find it’s a changing relationship. Maybe in the morning the CAM2 connects to CAM1, in the afternoon you find CAM2 connects to the NVR directly.

It’s not hard to understand. WiFi signal is something invisible and changing. Maybe in the afternoon you had your iPad in your room, your NVR in the living room is less interfered, CAM2 finds the NVR itself a better hotspot to connect.

After the test run, as long as you have all cameras streaming well to the NVR, you can mount them to their tested spots. (regardless how many WiFi bars they give you)

If you do have a camera that is hard to connect after adjusting other cameras’ locations, you should go ahead to mount the other cameras, then come back to this very camera.

You have 2 solutions：

1. Hard wire that camera, here is how to,

https://support.xmarto.com/?action=faq&cat=1&id=50&artlang=en

2. Add an RPT20 physical WiFi camera repeater for that camera,

====

Version 2 camera systems

For customers who has older version 2 camera systems, you can manually set a middle camera as a WiFi repeater. Click to see more details

 View More >> 

How to enable PTZ camera auto tracking on the NVR/Phone ?

When you add the PTZ cameras to the exsisting system as add-on cameras:

Go to System setting-CH Setting- Video Detection and enable the Motion Detection Tracking

On NVR version 3.2+

1. Click the image of a camera to pop-out the quick menu on bottom. Click ‘PTZ control’ to enter PTZ menu.

2. In PTZ menu, use the joystick to move the camera to where you want. Type preset ‘1’ and save. This point is saved as preset #1.

3. Enter ‘Auto tracking’ menu, check ‘Motion detection tracking’ and ‘Home point’, type preset 1 as the home point and Apply.

The camera will return to preset 1 after the tracking.

On the phone：

Run the app, click “…” at upper right corner of your device, Choose “Device Setting”

In “Smart Detection“, Enable the Motion Detection Tracking

====

If your NVR firmware is earlier than 3.1.4.4, or your camera version is older than 3.6.28; you need to upgrade your camera/ NVR to obtain the auto track feature. 

1. Update your NVR version to 3.1.4.4 or higher

Online upgrade: make sure your system is getting online condition.

Right click your NVR mouse>System setting>System Admin>System upgrade, choose Online upgrade, check upgrade when download finished, click Start.

2. Download the camera firmware 3.6.28,

https://www.xmarto.com/download/firmware/IPG5323_W_20210803_3_6_28_572010(1).rom

3. Put the file to your USB flash disk’s root directory, not in any folder.

4. Plug the USB flash disk to your NVR’s USB port.

5. Go to System setting-CH Setting- IPC Maintenance, choose the firmware from USB Storage, and click start to update the firmware of your camera.

6. Go to System setting-CH Setting- Video Detection and enable the Motion Detection Tracking

Now, your PTZ camera DZ2034/DZ20313, DT3034/DT30320, WT2054/WT20512, DPM2024 can achieve the auto tracking function when they connect to the NVR system.

==

XMARTO PTZ cameras has a lot of advanced features if you are interested. Please refer to the XMARTO PTZ camera command codes manual,

https://cdn.shopify.com/s/files/1/0628/9912/6502/files/XMARTO_PTZ_Dome_Camera_Command_Codes.pdf?v=1649837464

How to set home point for XMARTO Auto-Track PTZ cameras?

The XMARTO PTZ cameras have Auto-Track function. The Auto-Track is an AI feature that tracks activities and record.

It makes sure to record what happened even while you are not watching.

A concern comes along with the Auto-Track: would the camera track and view the wall or ground, and never come back to the entrance it was watching?

You can set a home point for the PTZ cameras. The camera will return to this key point after each track. 

Follow below steps, you can set your default view point.

1. Set Home Point On APP

While viewing the camera in App, tap PTZ and use the joystick to move the camera to watch the spot you want. (such as an entrance)

Then tap Preset to enter preset menu.

In Preset menu, tap the + sign to add preset points.

The 1st preset point will be the home point.

The camera will return to this point after each track.

   =>    =>  

Tap the Edit sign, you can delete and change preset points, including the 1st home point.

2. Set Home Point in NVR Menu

If your camera is used with a NVR, you can also set the home point in NVR menu.

a) while viewing the camera on NVR screen, click the image of a camera, you will see a pop-out menu on bottom. Click PTZ control to enter PTZ menu.

b) In PTZ menu, use the joystick to move the camera to where you want. In preset type 1 and save. This point will be saved as preset #1.

c) Switch to Auto tracking menu, check Motion detection tracking and Home point, type 1 as the home point and Apply.

The camera will return to preset 1 after each tracking.

NOTE:

1. If your NVR does not have this Auto tracking menu, upgrade your NVR to latest version
2. If your NVR does not have this Auto tracking menu after the firmware upgrade, set the home point from mobile App.

How to replace my old NVR without pairing each camera again?

XMARTO’s long range WiFi security camera systems have been the best sellers on Amazon during 2015 – 2016.

Many customers’ security camera systems were runnning for 6-7 years, 24 hours per day, 7 days per week.

With that workload, some customers feel the necessity of replacing their old NVRs, or some of their old cameras.

Is there a way to swap the old NVR out without taking all cameras down for pairing? 

The answer is affirmative. 

As you may already know, the NVR itself is also a WiFi router.

The theory is simple: each time you replace your old WiFi router, you only need to set your new WiFi hotspot name and WiFi password exactly the same as before, your devices will automatically reconnect. Same thing for XMARTO NVRs.

Here are the steps replacing your old NVRs without re-pairing all cameras:

Step 1: Record the WiFi information of your old NVR. 

As showed in below image, in your old NVR’s menu, navigate to System Setting – Network setting – WiFi setting, you will see the ESSID and password information, which is the WiFi name and WiFi password of this NVR. Take a photo to record this information.

Step 2: Revise your new NVR WiFi information to the same as old NVR’s. 

Swap your old NVR out and plug your new NVR, enter the same WiFi setting. Revise the new NVR’s ESSID & password to exactly the same as on the old NVR.

Step 3: Find your cameras back

With the old WiFi information on the new NVR, your cameras are connected with the new NVR.

Now you need add the cameras to your NVR channels.

In the NVR menu, right click – Camera Manage; click Search till you see your cameras listed in the above box. Then click ‘Add One’ to add the cameras to NVR channels.

Your cameras will be added to the channels in the below box and work as before.

 

FAQ

1. My old NVR is still working fine. Should I upgrade it to a newer one?

Not necessarily. As long as they are working fine. You don’t have to upgrade the NVR, or the camera.

    2. I plan to add the latest XMARTO PTZ camera, or solar cameras to my old system. Is it compatible?

XMARTO products are compatible with each other. But if your NVR is 960p or 1080p, they are not capable to take in the new 3MP & 5MP cameras.

Please check your NVR’s version in System admin. If you have version 3.0+, you can feel free to add latest cameras. If your NVR version is earlier than 3.0, please consider to upgrade your NVR (hardware) to the latest model.

    3. What if my old NVR does not turn on and I cannot enter the menu?

Please try to open the old NVR, unplug the 2 cables on hard drive, see if you can enter the menu to record old WiFi information.

If you cannot enter the old NVR’s menu to find WiFi info, you will need to pair your cameras to the new NVR one by one. Here is how to,

https://support.xmarto.com/?sid=229823&lang=en&action=faq&cat=1&id=15&artlang=en

“Incorrect password” while viewing XMARTO cameras from App

The XMARTO home security systems have 2-layer of security password.

1. The NVR device password (AKA the admin password)

Each time you access the NVR menu, it requires the admin password. Without a device password, users will be locked out.

Device admin password can be set when you follow the 1st time initial setup, or at any time in System setting – System admin – User.

This is very important and we suggest you to set and remember your admin password at 1st time.

This device password (device lock) is local and it locks access to your NVR, no matter whether your NVR has Internet connection or not.

2. App login password

Like using any Internet service, using WallPixel App requires you to create an user account.

Your App user account is normally an email address or a phone number; and the password is the code protecting your user account.

If you don’t have a WallPixel App user account, tap Register to create an user account.

The App user account is different from your device admin password. They are 2 sets of combinations.

The NVR admin password is a local password locking your NVR; the App user account password is an Internet password locking access to your WallPixel user account.

3. The connection

The connection between App user account and the NVR/ camera is based on Cloud ID.

The Cloud ID is an unique ID number of a XMARTO NVR or camera. On most NVRs/ cameras, you can find a QR code indicating the device’s Cloud ID. You can also find the Cloud ID on NVR screen’s below right corner.

To access the Cloud ID corresponding device, you need to provide the device password. Without the password, you will be locked out.

As advised in the manual, when you add the NVR/ Camera to the App, you are lead to provide the admin password,

        

The password here refers to the NVR/ camera’s admin password, not the App user password.

Provide your admin password, you will be able to view the cameras remotely from the App.

If you are an authorized user by the administrator, provide your user name and your password.

4. Update device password

If you’ve changed your admin password lately, you need to update it to the App.

 =>   => 

A few important tips

1. The default password
   If you skip setting a password for your NVR or camera, then the default password is empty.
   You leave the password area empty and tap next to view the cameras or access the menu.

   That also means, theoretically anyone who knows your Cloud ID can access the NVR/ camera. (although no one will know your Cloud ID unless you show them). So it is strongly suggested to set an admin password; as soon as you start to use the XMARTO NVR/ camera.

 2. Secondary users

If you are running a store, an office etc; in the System setting – System admin – User setting, you can add a few users with secondary permissions.

Then give those secondary user accounts to your employees. For example, you added user “JohnWayne” with password “batman”.

When he try to access the NVR’s screen, he needs to change the username from “admin” to “JohnWayne”, then enter password “batman” to access the NVR menu.

Same thing in the App. Obviously John Wayne needs to create his own App user account with his own email or phone #.

Then when he add the NVR system or camera to App, he input or scan the Cloud ID, provide his own NVR/Camera access combination, to access the NVR/ camera, with your nominated permissions only.

3. That sounds way too complicated. “I’d simply let my families know my Cloud ID and admin password so they can view” 

Not suggested. Logically, the WallPixel Cloud will take the 1st App user who added the Cloud ID as the owner.

If you have a 2nd or 3rd user adding the same Cloud ID as admin, 1 or few of you may miss some features, such as the App notifications.

The correct way is to use the Sharing feature.

a) let your families download and install WallPixel App, then create his/ her own App user account.

b) in the App, tap sharing, set sharing perimissions and valid time. Then send the QR code to your families.

c) In WallPixel App, your families scan the QR codes to add the camera/ system.  (no matter where they are)

4. “My XMARTO security system have 4 cameras and a NVR. Does that mean I have 5 Cloud IDs?”
No, when you use a XMARTO camera system, the App only takes the whole system as a single device; so it recognize only the NVR’s Cloud ID; and let you view 4 to 10 cameras simultaneously in App, just like what you see on the NVR’s screen.

Privacy tips

1. Does XMARTO know my device admin password?
   No we don’t. The device password is a local password you set in the initial setup. We cannot know that.
   If you forgot the password, the only way is to hard reset it.
   About how to reset password, please contact support@xmarto.com
   The hard reset can be done only by yourself, with the hardware in hand.
2. Does XMARTO know my App user password?
   No we don’t. Any App attempts to collect user’s password will not be approved by App Store or Google Play.
   If you forgot the App user password, the only way is to tap “Forget password” and follow steps to reset password, or simply create another user account.
3. If someone hacks my App user account, what should I do?
   That never happened. But if you believe someone hacked your App user account, the 1st thing to do is tap “Forget password” in App to reset your user password; or contact support@xmarto.com to know how-to hard reset your device password. Any of the 2 password reset will lock the access immediately.

   For standalone cameras, please change the device password in device setting; or hold reset button to reset the camera and set it up again.
   For NVR or NVR systems, the way of hard resetting password is not public. Please contact support team with your order # to learn how to reset NVR admin password.

   Relax, it’s almost impossible to happen.

<p>The post XMARTO NVR WiFi PTZ Camera System FAQ first appeared on NVR IPCAMERA SECURITY.</p>

Amcrest Surveillance Pro is the most stable and recommended method of accessing your devices from your computer. It is free software provided by Amcrest that can provide a means of accessing all your devices in one central location without the use of a plugin or web browser. For more information on how to install Amcrest Surveillance Pro using Windows, please refer to the information provided below.

Note: This is a 64-bit version. If you are using Mac to install the Amcrest Surveillance Pro software, click here.

How To Install Using Windows

To install the Amcrest Surveillance Pro software on your computer, click here.

To begin installing the software, double click the provided .exe file. to begin the installation. Please note, if you have Windows Defender SmartScreen or certain versions of Norton running on your machine, please allow the software to be downloaded on your device. If Windows Defender is blocking the software, click on More Info then click on Run Anyway to begin installing.

Please note, this is a trusted software and will not harm or have any negative impact on your machine.

On the initial setup screen, select your language from the Select Language dropdown menu. Click on the I have read and agree checkbox and agree to the End-User License Agreement (“EULA”) agreement. To read the agreement, click on the agreement link provided. Once complete, click Next to continue.

Select the functions that you want to install with the software. You can choose to bundle the PC-NVR function with the software. PC-NVR turns your computer into an NVR and will utilize your hard drive (HDD) on your PC to store and access recorded video. To proceed with the installation, click Next.

Select an installation path for the software. To choose a folder, click on the Browse button and select the folder. Once a folder has been selected, click the Install button to begin installing the software on your computer.

Please note, if there is an older version of Amcrest Surveillance Pro detected on your machine, the new software will overwrite the old software. However, the device list information will still be reserved. Click Install to install the new software.

To generate a shortcut icon for the software on your desktop, click the Generate shortcuts checkbox.

Once the software has finished installing you will see a few options available. You will have the option to view the release note and run the Amcrest Surveillance Pro software. To begin running the software directly after pressing finish, select the Run Amcrest Surveillance Pro checkbox and click Finish to proceed.

Setting a Password

After the installation of the Amcrest Surveillance Pro software, you will need to set an administrator password. This password will be the admin password for the software. When a valid password has been entered, confirm the password in the Confirm Password field and click Next to continue.

This software provides password protection questions which can be answered in the event that you lose or forgot your password for the software. Select an applicable question from the Question dropdown menus and fill in the answer for those questions in the Answer field. Click Finish.

The software has now been properly installed on your machine. The password for the software will be saved by default on the login screen. If you would like to have your computer remember this password whenever you open the software, click Remember Password. If you would like the software to automatically log you in whenever your machine is reset, click Auto Login. Click Login to open the software.

How To Install Amcrest Surveillance Pro on Mac

Amcrest Surveillance Pro is the most stable and recommended method of accessing your devices from your computer. It is a free software provided by Amcrest that can provide a means of accessing all your devices in one central location without the use of a plugin or web browser. For more information on how to install Amcrest Surveillance Pro using Windows, please refer to the information provided below.

Note: If you are using Windows to install the Amcrest Surveillance Pro software, click here.

How To Install Using Mac

To begin installing the Amcrest Surveillance Pro software on your computer, click here.

The download will be a Google Drive link, however, please be assured this is a trusted software and will not harm or have any negative impact on your machine. Download and open the .pkg file.

Note: Your machine may recognize this as a coming from an unidentified developer and cannot be opened. Do not worry, it doesn’t mean that there is anything wrong with the software. You can easily override your settings and open the product by following these official steps recommended by Apple.

1) In the Finder, click on the Downloads tab and locate the Amcrest Surveillance Pro pkg.

2) Click on the Apple icon in the upper left corner and select System Preferences.

4) In the System Preferences menu, click on Security & Privacy.

5) In the General tab, click on Open Anyway to begin opening the Amcrest Surveillance Pro software.

6) Click on Open.

7) In the Installer prompt, click on Continue to be guided to the steps necessary to install this software.

8) Select a Destination for the software and click Continue.

9) Click Install (enter any security passwords needed for your machine and click Install Software).

10) The .pkg has now been installed on your machine. Click Close to exit. The Installer can be kept on your system or moved to the trash if you would like.

11) Click on Finder and open the Applications tab to locate the Amcrest Surveillance Pro software. Double click on the application to open the software.

Setting a Password

After the installation of the Amcrest Surveillance Pro software you will need to set an administrator password. This password will be the admin password for the software. When a valid password has been entered, confirm the password in the Confirm Password field and click Next to continue.

This software provides password protection questions which can be answered in the event that you lose or forgot your password for the software. Select an applicable question from the Question dropdown menus and fill in the answer for those questions in the Answer field. Click Finish.

The software has now been properly installed on your machine. The password for the software will be saved by default on the login screen. If you would like to have your computer remember this password whenever you open the software, click Remember Password. If you would like the software to automatically log you in whenever your machine is reset, click Auto Login. Click Login to open the software.

<p>The post How To Install Amcrest Surveillance Pro PC MAC first appeared on NVR IPCAMERA SECURITY.</p>

What is CCTV Camera Software for PC?

The Software for PC is designed and developed by the CCTV camera manufacturers for their security solutions and products. This helps to connect as well as control the CCTV cameras on PC. Here we provide you with the top 25 CCTV Cameras Software for PC.

Application of these CMS

These CMS allows users to connect and maintain the CCTV system with your PC. With these applications, it becomes easier to get the live view of your residence, family, office premises and locality. With these applications, You can access the CCTV from remote locations as well.

it is now easier to connect and maintain on your security online through CCTV cameras. CCTV cameras are the best security solution to enhance the security of family members and others.

Importance of the CMS

These CMS helps to connect as well as control the CCTV cameras on PC. These CMS acts as an intermediary between PC and CCTV camera set up to help the user client to provide access to the user of CCTV camera on PC. We will highlight some of the important functions which can be performed by the application.

• Remote Access.
• Connectivity and control
• Video Surveillance.
• CCTV Video recording.
• Live monitoring on a different viewpoint.
• PTZ camera controlling.
• Remote playback of the recording.

List of Top 25 CCTV Camera Software for PC

Here we will discuss in detail about the application for PC. We provide you with the top 25 CMS. CCTV cameras are available for Windows and Mac operating systems. But some CCTV manufacturers do not provide the application for Mac user clients.

The download file of every CMS is in the compressed format and use WinRAR to extract the downloaded file. Besides, get better knowledge regarding the CMS installation and setup procedure by clicking the links.

The list of the best CMS is as follows:

1. IVMS 4500 by Hikvision

IVMS is also one of the best CMS developed by Hikvision Company. This CMS is the best application in the market to connect as well as control.

Hikvision is a global leader in the provider of security solutions and products. Emphasizing on the comprehensive and highly skilled R&D team, Hikvision manufactures a wide range of products. Hikvision has broadened its field to smart home tech, industrial automation, and automotive electronics industries to realise its long-term goal.

Hikvision products also render powerful business intelligence for clients, which enables more efficient transactions and greater commercial profit. Hikvision is a global leader of IoT solution provider with video as its core competency. Hikvision now has above 19,000 R&D engineers. The company yearly funds over 9% of its annual sales revenue to research and development for continued product innovation.

IVMS 4200 & Storage Server

The application is provided by the Hikvision company. The free download link is provided below. IVMS 4200 installation procedure is here as well, click on the link of IVMS 4200. Also, read the instruction of IVMS 4200 storage server as well.

Download IVMS 4200 For PC (Windows) V3.1.1.13

IVMS 4200 For PC (Windows) Download VS V1.0.0.13

Free Download IVMS 4200 AC V1 For PC  AC V1.0.1.13

Download Multi lang.  IVMS 4200 For PC  Multilingual Package V3.1.1

IVMS 4200 For PC Multilanguage for PC   Multilingual Package AC V1.0.1

Multi-language VS V1  IVMS 4200 For PC   Multilingual Package VS V1.0.0

Free Download IVMS 4200 for PC (MAC)   MAC V2.0.0.10

Download IVMS 4200 Storage Server for MAC

Download IVMS 4200 Storage Server for Windows

IVMS 4500

We have provided you with the IVMS 4500 for PC free download link below. Get the free download link. Read the installation procedure of IVMS 4500 here.

Download IVMS 4500 For PC (Windows)

Download IVMS 4500 for PC (MAC)

2. Smart PSS by Dahua

We provide you here with the Smart PSS by the Dahua Company. The Smart PSS helps connect the CCTV cameras on your PC. The CMS has many features and functions to help the user to connect, live stream, PTZ control, etc.

Zhejiang Dahua Technology Company is a leading company in video-centric smart IoT products and service provider. Dahua Technology Company renders end-to-end security solutions, products, and services to create values for city operations, corporate management, and clients.

Dahua solutions, products, and services are in over 180 countries and regions. Dahua Technology has 54 subsidiaries companies and branch offices globally in Asia, the Americas, Europe, Middle East, Oceania, and Africa.

Smart PSS

Here is the free download link of Smart PSS for Windows and Mac OS. Also, read the instruction of installation procedure in the article of Smart PSS.

Smart PSS For PC Free Download (Windows)

Smart PSS For Mac Free Download

3. NVMS 1000 by TVT

NVMS is one of the famous application developed for the TVT CCTV camera brand. This application provides you with many features to administer your CCTV camera on PC. The CMS is a free download here, through this you can get the following features:

• Remote Access
• PTZ Control
• Live stream
• Recording videos

TVT brand of CCTV camera is manufactured and distributed by the Shenzhen TVT Digital Technology Company established in 2004 and headquarter in Shenzhen, also listed on the SME board of Shenzhen stock exchange in December 2016.

As a worldwide best quality security solutions and products provider in more than 120 countries apart from China. Ranking as the most advanced company that enters into the abroad market in the video monitoring industry in China, TVT has established an independent and perfect marketing service system.

NVMS 1000

Here is the download link for NVMS 1000 for Windows and Mac OS. You can read about the installation procedure as well by clicking on the link of NVMS 1000.

NVMS 1000 for Windows 10

NVMS 1000 for Windows 10

NVMS 1000 for Mac OS

NVMS 7000

Get the free download as well as free installation procedure on NVMS 7000. This is available for Windows and Mac OS.

Free Download NVMS 7000 for PC (Windows)

NVMS 7000 for MAC Download Free

NVMS 2.1

We provide the latest application provided by the TVT known as NVMS 2.1 for Windows OS. This CMS is only available for the Windows operating system. Read the installation procedure of NVMS 2.1 here.

NVMS Lite 2.1 Download Free

4. KVMS Pro by CP PLUS

We provide you here KVMS provided by the CP Plus Company. KVMS Pro provides you with a wide range of functions and features as well. With this, you can connect CP Plus CCTV camera setup with the application on Windows and Mac.

CP PLUS is the global leader in high-level security and surveillance solution. Inspired by the vision and commitment to make surveillance easy and affordable, CP PLUS has begun a mission to make the world a safe and secure community.

As per the IHS Survey 2017, CP PLUS attains as the most recent and most active brand to enrol the club of Top 4 security companies in the world and Top 2 in Asia. CP PLUS attribute their path-breaking success to sound R&D leadership. CP PLUS products pass through stringent quality-control tests and are globally certified by the certificates such as UL, CE, FCC, etc.

KVMS Pro

Here is the CMS of KVMS Pro free download link for Windows and Mac OS. Read the instruction of installation procedure to install the KVMS Pro here.

Free Download KVMS Pro for PC (Orange)

Free Download KVMS Pro for PC (Blank)

Free Download Indigo CVMS for Mac

Indigo IVMS for Mac Free Download Free

5. EZStation by Uniview

Here we are about to discuss the EZStation developed by the Uniview. With this, you can connect as well as perform other functions to control the CCTV camera on your PC. With this, you can get many features such as live view, audio-video recording, etc.

Uniview is the global leader of IP video surveillance. First-ever company to introduce IP video surveillance in China, Uniview is the third-largest player in the video surveillance industry of China. In the year 2018, Uniview has the 4th largest global market share in the surveillance industry.

Uniview has a wide range of IP video surveillance products ranges from IP cameras, NVR, Encoder, Decoder, CMS Client, and app, covering several markets sectors including retail, building, industry, education, commercial, and city surveillance.

EZStation

Get here the download links of EZStation as well as the installation procedure of EZStation.

EZStation for PC (Windows 32 Bit)

EZStation for PC (Windows 64 Bit)

Download EZStation for MAC

6. Guard Station by Uniview

Guard Station is also another applicaton provided by the Uniview Technology Company. This CMS provides you with a variety of software to connect as well as control the Uniview CCTV cameras. This app provides functions such as PTZ Control, live streaming, video recording etc.

Guard Station

Here is the free download link of Guard Station for Windows and Mac OS. For the process to install the Guard Station read here.

Guard Station Software Download for Windows

Guard Station For MAC

7. Wansview Cloud by Wansview

Here we provide you with the Wansview Cloud which is designed and developed by the Shenzhen Wansview Technology company. It provides you with the capability to monitor your premises from remote locations on your PC. Wansview App for PC helps to connect as well as control the CCTV cameras.

Established in 2009, Wansview dedicated to product design, development technology innovation, and professional manufacturing processes in the field of security solutions and products. Wansview has clients in more than 100 countries in the world, such as the United States, Germany, Britain, France, Canada, Spain, Italy, Russia, Brazil, etc.

Wansview Cloud

We provide with the free download of the Wansview Cloud for Windows and Mac as well as the installation method.

Free Download Wansview APP for PC (V1.0.2)

Wansview APP for PC Free Download (V1.0.3)

Download Wansview APP for MAC Free(V1.0.3)

8. MI Home by Xiaomi

Here we provide the MI Home for PC to connect the Xiaomi’s MI Home CCTV cameras. This CMS is only available for Windows and Mac OS. The application provides remote access, live view and connectivity at any kind of network.

Xiaomi Inc. is a China-based company which deals in electronics and security products. This company has been taken good care of its clients and has a greater market share by providing the product at affordable prices.

MI Home

Now get the free download of MI Home for Windows OS. Also, read the instruction to install the MI Home on Windows.

MI Home Security Camera App Download For PC

9. V380 CMS By V380 Camera

We provide you with the free download of V380 which is designed and developed by the V380 Camera. V380 software helps you to connect the V380 CCTV cameras and helps to maintain surveillance over the home, locality and office premises. The app is available only in Windows OS.

V380 Camera is a most-advance company that engages in R&D, production, marketing, and service of the V380 Wifi Smart Camera, V380 IP Camera, and V380 360 Panasonic Camera. V380 Camera is one wifi camera brand in the company which aids to create intelligent terminal products.

V380 Software

Get the free download of V380 for Windows OS. Also, read the installation instruction of V380 software here.

Download V380 App for PC

10. PVMS By Panasonic

Here we will discuss the PVMS software developed by Panasonic Company. PVMS is one of the best CMS provided by the Panasonic Company. This is available only for the Windows operating system, this application helps to connect the CCTV cameras, provide remote playback, System configuration and video intercom.

Panasonic is a Japanese company established in 1935, with more than 259,000 employees. Panasonic deals with different kind of CCTV cameras and software. Panasonic has been one of the largest electronic appliances manufacturer in many countries.

PVMS software

The free download link of PVMS is available here. Also, get the installation guide by visit the article of PVMS.

Free PVMS Download for PC

11. Idmss Lite by Dahua

Idmss Lite software is also provided by the Dahua Technology company. Idmss Lite for PC is available for free download. The performs various functions such as live streaming, PTZ control, playback video, record video, snapshots, etc.

Idmss Lite

We have provided the instruction of installation in detail in the link of Idmss Lite here.

Free Download Idmss lite for PC

Free Download Idmss lite for Mac

12. DMSS by Dahua

Get here the DMSS by Dahua Technology Company. DMSS is the mobile application provided by the Dahua Company. This app is available for Windows and Mac user client, this CMS provides the user access to their Dahua CCTV cameras.

DMSS

Here is the free download of the DMSS as well as the procedure to install the DMSS software.

Free DMSS  for Windows 7/8/10 Download

Free DMSS for MAC Download

13. EZVIZ App by Uniview

EZVIZ App is also another application designed and developed by the Uniview Technology Company. This CMS helps to connect the as well as provides multilingual support to the users. This software is available for Windows as well as Mac OS.

EZVIZ App

Download free and also read about the installation procedure of EZVIZ App here.

Download Ezviz App For PC Windows 7/8/10

Download Ezviz App Video Plugin  Windows

Download Ezviz App Video Plugin

14. Velocity by HiFocus

HiFocus CMS is designed and developed by HiFocus Electrovision Company for its security solutions and products. HiFocus CMS helps to connect as well as control the CCTV cameras on your PC. HiFocus CMS for PC is the best security solution provided for the HiFocus CCTV system in the market.

Hi-Focus aims to bring the most advanced CCTV surveillance systems that can combine high volumes of data to produce essential information. The system provides users with advanced scrutiny, analysis, interpretation, and management. HiFocus assistance helps in the deployment of fast and intelligent security system solutions through a complete analysis based on the position and location of the device.

India’s trusted CCTV Company, Hi-Focus provides its customers with the best end-to-end video analytics solutions with the best surveillance cameras accompanying integrative proficiency to understand customer’s behaviour and other essential operational indices.

Velocity

Here is the free download of Velocity by the HiFocus, also read the installation procedure of Velocity.

Free Download Hifocus CMS Software for PC

Hifocus CMS Software for MAC Free Download

15. Smart Viewer By Hanwha (Samsung)

Hanwha Security Company has developed the Smart Viewer to connect the Hanwha CCTV cameras. The CMS provides you up to 72 channel of CCTV cameras view on screen, search recorded data by event type and date, export video and dual monitor support.

Hanwha Techwin America (Samsung Techwin) is a security technology company that has exhibited stable growth for the past 40 years and is part of the Hanwha Group. Hanwha Techwin is a Fortune 500 company and also one of the conglomerates in South Korea considered to be the largest.

The Hanwha Group has the expertise of over 60 years in the manufacturing of the video surveillance industry. The company has created many clients across the globe by providing the best quality product and services.

Smart Viewer

The link to download the Smart Viewer is free here. And visit the installation procedure article of Smart Viewer.

Download Smart Viewer For PC (Windows)

Download Smart Viewer For MAC

16. Wiseview by Hanwha (Samsung)

There is another software also to connect the Hanwha CCTV cameras also known as Wiseview. This provides you with some features as dual-screen assistance, live streaming, log administration, and user management.

Wiseview

Get the download of the Wiseview for free and installation guidelines as well.

Free Download Wiseview for PC (Windows)

Wiseview for MAC Free Download Free

17. Night Owl Connect By Night Owl

Night Owl Connect is designed and developed by the Night Owl Company for Night Owl CCTV cameras. This software has features such as IP device configuration, group management, main preview and log search functions. This feature helps the user to connect the CCTV cameras.

Night Owl Security Company is a leading innovator in the security technology industry. It is the fastest-growing manufacturer of security solution and products which offers the best value on the market. This is accomplished by designing and engineering products that are of high quality, user friendly, and affordable.

Night Owl Connect

Download free Night Owl Connect software for Windows and Mac OS. Read the guidelines for installation of Night Owl Connect.

Download Night Owl Connect for PC (Windows)

Download Night Owl Connect for MAC

18. Guarding Vision

Here is the Guarding Vision for PC developed by the Guarding Expert. This CMS helps us to connect as well as control the CCTV cameras on PC. This provides you ability to connect multiple CCTV camera brand on the same software. This application is available for Windows and Mac operating system. Guarding Vision helps us to detect motion as well.

Guarding Vision

Now download free Guarding Vision for Windows and Mac as well as learn about the installation procedure.

Free Download Guarding Vision for PC (Windows)

Guarding Vision for MAC Download Free

19. HiP2P Client by Dericam

Here we provide you with the HiP2P Client software for connecting and administering the Dericam CCTV cameras for PC. HiP2P Client is available for Windows and Mac user clients, this provides you with the ability to control Dericam CCTV cameras on PC.

Shenzhen Dericam Technology Company was formed and established in the year 2010. The company is developing, manufacturing, and marketing IP cameras and storage devices for home security field. Currently, Dericam has clients in the US, Australia, Netherlands, France, Poland, and other countries as well.

Dericam aims to innovate and develop its products to meet the demands of customers. Dericam continues to innovate and develop the quality of its products, enable everyone to enjoy the benefit of advanced technology. All series of products are CE & FCC certified.

HiP2P Client

Here get the download of HiP2P Client for free and read carefully the installation method of HiP2P Client.

HiP2P Client Software Download Free

HiP2P Client Software Download For MAC

20. YI IoT By YI Technology

Here we will discuss in detail about the YI IoT software which is designed and developed by the YI Technology Inc. YI IoT software helps you to connect the YI IoT camera and YI Dome Camera on your PC. This software provides you with cloud encryption and real-time push notification alerts. This is only available for Windows OS only.

YI Technology strives to deliver enhanced security and productivity to clients globally through high-quality hardware and cutting-edge. YI Technology is committed to rendering users with convenient and affordable technology emphasizing the latest and greatest Edge Computing features as well as highly advanced AI algorithms.

YI Technology develops and manufactures intelligent video and imaging solutions using the latest technology to solve real problems for its clients. YI Technology values its clients’ security and privacy and employs a 128bit end-to-end encryption to keep clients data safe.

YI IoT

Here get the free download now of the  YI IoT as well as the installation method for Windows OS.

Free Download YI IoT App for PC

21. YI Home By YI Technology

Here is another software developed by YI Technology known as YI Home. This also helps to connect as well as control the YI Home and YI Dome cameras on PC. This provides various features which are similar to YI IoT.

YI Home

Get the YI Home free download link and installation procedure guidelines.

Free Download YI Home App for PC (Windows)

YI Home App for Mac Free Download

22. DW VMAX By Digital Watchdog

Let us learn about the DW VMAX software which developed by the Digital Watchdog a leading CCTV camera manufacturing company. The DW VMAX is available for Windows, Mac and Linux OS. The has features such as PTZ control, live image quality enhancement, zoom in and out option on live streaming, multiple as well as single video export, 4/6/8/16 or 32 Channel view on PC and audio communication.

Digital Watchdog (DW) is a leader in surveillance cameras and associated video management, delivering complete video surveillance solutions for HD over Coax and HD IP CCTV systems of any size and for any application.

DW VMAX

Get the free download of DW VMAX for Windows, Mac and Linux OS here, read the installation procedure correctly of DW VMAX.

Free Download DW VMAX for PC Windows x64(Version – 4.1.0.31401)

DW VMAX For MAC Download Free x64(Version – 4.1.0.31401)

Download DW VMAX For Linux Free x64(Version – 4.1.0.31401)

23. CloudSEE by Jovision

We provide you with CloudSEE developed by the Jovision Technology Company. CloudSEE helps to connect the Jovision CCTV cameras. This provides video recording on a live camera, play recorded videos., assistance real-time playback when preview, playback supports quick, slow, and by frame modes, local snapshots, and recordings and files stored locally.

Jovision Technology Company established in the year 2000, is the world’s preeminent manufacturer and distributor of video surveillance products and solutions. Jovision is recognised in developing and manufacturing highly advanced video surveillance products.

Following are the new main researched and developed product of Jovision Company, smart IP cameras, WiFi cameras, NVR, DVR, HD Analog cameras, CMS video management software, alarm systems, encoders, decoders, and CCTV modules. Jovision’s expert engineers also provide customized security solutions.

CloudSEE

Here is the free download of CloudSEE for Windows OS because the CMS is only available for Windows OS. Also, read the installation procedure carefully of CloudSEE.

Free Download CloudSEE For PC

24. SwannView Link by Swann

We will discuss in detail about the SwannView Link developed by Swann Communication is the best CMS to connect the Swann CCTV cameras. SwannView Link helps you to connect the CCTV cameras on your PC. This provides brightness adjustment, live view and application user management.

Swann has always been a leader. Begins its business from the Swann’s personal house basement in Melbourne, Australia. Swann has established and created its clients in the USA, Canada, Australia, UK, Hong Kong and China and also in other 40 countries.

Swann provides surveillance and monitoring technology by introducing its new product such as wireless HD cameras, video surveillance recording systems and cameras, and also 4K Ultra HD, 3-5 Megapixel HD, and 1080p HD camera setup with temperature and motion sensors technology.

SwannView Link

Get the download free now of SwannView Link, read the instruction of installation of SwannView Link.

Download SwannView Link For PC (Windows)

Download SwannView Link For PC (MAC)

Download SwannView Plus For PC

25. Amcrest View Pro by Amcrest

Here is the Amcrest View Pro designed and developed by the Amcrest Company. This application helps to connect the Amcrest CCTV cameras on your PC. This CMS provides features such as user management, live streaming, playback recording, etc.

Amcrest products are advance designed remote monitoring and surveillance systems which build a bridge between powerful capabilities, ease of use and affordability. With high quality and robust design, Amcrest cameras allow the user to securely monitor their residence, office premises etc. Amcrest camera systems are designed to record and produce live video and audio to the user anywhere in the world.

Amcrest is a top security products manufacturer as well as distributor servicing many clients worldwide primarily across the United States, Canada, the UK, Germany and France. Amcrest provides after-sales support and local warranty services to all of our customers in their local countries for free of cost.

Amcrest View Pro

Here is the free download of Amcrest View Pro free download and installation guidelines.

Free Download Amcrest View Pro for PC (Windows)

Amcrest View Pro for MAC Free Download

Conclusion

Here we have discussed some of the top 25 CCTV camera software for PC. These are the best softwares to control the CCTV cameras on your PC. The softwares are available to download free.

This CCTV software provides you with many features like a live recording, video snapshot, audio-video display, motion detection, night vision, and alarm notifications as well. With these CMS it easier to connect as well as manage the CCTV cameras.

We have discussed in detail about the “Top 25 CCTV Camera Software for PC“ in detail with the free download link of the software as well. For more information and query you can contact us by commenting on the comment section below of the article.

<p>The post Top 25 CCTV Software Free first appeared on NVR IPCAMERA SECURITY.</p>

As with many devices, dvr, nvr and ip cameras have a user name and login password by default.

This information is usually included in the user manuals of the devices.

If you have purchased a Vguard branded security product, the fabrication username and password for these products are as follows.

Username:  admin

Password:  vguard

DVR and NVR Password Reset with Super Password

Monitoring Vguard Recorder from Computer

If you want to watch the security cameras connected to your Vguard recorder on your computer, you can download the necessary software from the link below and install it on your computer.

Vguard CMS software username and password:

CMS Username:  admin
CMS Password:  no password, leave blank.

 You need to press OK button while exiting Vguard CMS software  . Pressing the Enter key on the keyboard we are used to cancels the program shutdown.

Vguard PC Monitoring Software Download (CMS)

Vguard CMS Port Number:  34567

If you are going to monitor remotely with cms using fixed ip, not from the local network, you need to forward this port (34567) number through the router.

If you do not have a fixed IP address, you can provide a remote connection with CMS via Vguard Cloud ID without the need for port forwarding.

Monitoring from Vguard Mobile Devices

You can download the Android or IOS application required for monitoring from Vguard Mobile Device below.

Vguard Mobile Port Number:  5801

If you are going to monitor remotely with your mobile device using a fixed ip, not from the local network, you need to forward this port (5801) number through the router.

If you do not have a fixed IP address, you can use the Vguard Cloud ID feature to establish a remote connection via your mobile device without the need for port forwarding.

IOS Link:

https://itunes.apple.com/en/app/vguard-mobil/id1153260591?l=tr&mt=8

Vguard Mobile Android Link:

https://play.google.com/store/apps/details?id=com.vguardmobil.eye&hl=en

If you have a question about Vguard security devices, you can send it in the comments section.

You can watch the details about CMS installation and usage in the video below.

<p>The post Vguard DVR/NVR And Camera Passwords New first appeared on NVR IPCAMERA SECURITY.</p>

Please plug DVR or NVR into the router with network cable if you wanna use a computer or phone to connect the recorder locally or remotely.

You can judge whether the recorder was connected to the internet by the status of a network like a picture below.

If the status is not connected, it means the recorder did not connect to the cloud successfully.

Here are the methods:

1. Please check the yellow and green light on the ethernet port of the recorder. One should be blinking which indicates the recorder has connected to the router successfully. If not, please change the ethernet port of the router or another reticle to have a try.

3. Go to the Main menu—-System—Network to confirm DHCP is ticked.

4. Please reset the recorder to the factory default setting.

5. If you can, please change the router to have a try.

Here is new CMS software:

for Mac:

http://www.sanncegroup.com/document/Computer%20software/General_VMS_Beta_Mac_En_V1.20.0.14_20191012.dmg

for windows computer:

https://download.annke.com/document/Computer_Software/General_Bate_CMS_V3.1.0.9.T.20190306.exe

Then you can follow the steps below to add NVR/DVR to your CMS.

1 Download CMS and install it on your computer according to the instruction in the download file.

2 Double click the icon  to open CMS, the default User Name is super, the password is blank (no password).

3 For the first time login, you will see the interface as below.

4 To add DVR/NVR, you can click the System menu on the bottom right corner. Then go to Device Manager, click ADD AREA to create a zone.

Name the zone yourself and click OK.

5 After adding an area, click the area name you created then click on to add your DVR/NVR.

Device Name: name it yourself

Login type: choose Cloud

Serial ID: Here is a method to find Serial ID

User Name/Password: default is admin and no password, same as your DVR

Click “ OK” after you have done the above parameters, you could double click to open this device.

6 After you add your DVR successfully, you can view and manage your DVR on CMS.

7 Here is the introduction to the CMS interface.

Note: If you have a problem adding DVR/NVR to CMS, please double-check the connection between

your DVR/NVR and the Internet and upgrade your CMS to the latest version.

<p>The post How to Connect DVR/NVR on Computer Software CMS? first appeared on NVR IPCAMERA SECURITY.</p>

<p>The post LILIN Aida Firmware Software Download first appeared on NVR IPCAMERA SECURITY.</p>

We constantly strive to keep our systems up to date. Should you still find errors / bugs, we would be delighted if you could report them to us. With your help, we can quickly and efficiently eliminate any errors.

We ask you to send the information to service@jovision.de. The more information, please note that you provide the following data in the mail:

– Camera type designation

– Camera firmware

– Error Description

IP camera instructions

Please note that there are two types of update variants. You should therefore make a good decision which variant you want to use.

Variant A (click here)

Variant B (click here)

Note:

With update variant B (special update / boot update) your camera is reset to the factory settings . All data and settings of the camera will be deleted . A new setup is then necessary.

NVR guide