ATTENTION: Prior to purchasing and installing an accessory antenna, read the product specifications of your receiver to determine if your receiver has a weatherproof housing. Installing your weatherproof receiver outdoors provides a better line-of-sight between the receiver and the camera, increasing the strength of the wireless signal. See your product specifications to determine the weatherproof rating of your receiver.

The Directional Wireless Panel Antenna and the Omni-Directional Antenna are used to extend the range of one or multiple wireless or wire-free cameras.

Directional Wireless Panel Antenna (ACCANTD9)

Omni-Directional Antenna (ACCANTO8)

Use the 2.4GHz Directional Wireless Panel Antenna (ACCANTD9) to focus a wireless signal onto one specific wireless device (camera or receiver) to increase the range of transmission. A clear line-of-sight between the antenna and the wireless device needing range extension is required.

Use the 2.4GHz Omni-Directional Antenna (ACCANTO8) to enhance the signal of one or multiple cameras that are paired to a single or dual antenna receiver. You may also use two Omni-Directional Antennas to extend the range of all cameras paired to a dual antenna receiver.

REQUIREMENT: To connect the antenna directly to the camera or receiver, the device must have a removable SMA type antenna. Visit www.lorextechnology.com/compatibility to ensure the antenna is compatible with your camera or receiver model.

Lorex Wireless Cameras and Monitors guide 2024

Also Read  : Lorex Camera Troubleshooting

Recommended Antenna Installation Methods

Your antenna needs will vary depending on the setup of your camera system, the number of cameras that require range extension, and the number of channels on your wireless receiver. Review the scenarios below to ensure you have the correct antenna and installation method to meet your needs.

Click a setup scenario to see the recommended installation method:

Combining Accessory Antennas

If you have installed your accessory antenna according to the recommended installation methods and would like to enhance wireless signal strength even further, you may add an additional Directional Wireless Panel Antenna (ACCANTD9) directly to a camera. The additional Directional Wireless Panel Antenna can be used with a Directional Wireless Panel Antenna or with an Omni-Directional Antenna attached to the receiver.

Click an antenna combination to see recommended installation methods:

Scenario 1: Extend the range of one camera paired to a single antenna receiver

To extend the range of one camera connected to a single channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9).

The Directional Wireless Panel Antenna can be connected in two configurations.

Configuration 1. Connect the antenna directly to the camera

Configuration 2. Connect the antenna directly to the wireless receiver

REQUIREMENT: The antenna connects using an SMA cable and replaces the existing antenna on either the camera or wireless receiver. Check www.lorextechnology.com/compatibility to determine if your product is compatible with the antennas.

Scenario 2: Extend the range of one camera paired to a dual antenna receiver

To extend the range of one camera connected to a multi-channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9). Connect the Directional Wireless Panel Antenna directly to the camera.

Scenario 3: Extend the range of select cameras paired to a dual antenna receiver

To extend the range of select cameras on a multi-channel receiver, use the Omni-Directional Antenna (ACCANTO8).

Connect the Omni-Directional Antenna to one of the antenna ports on the wireless receiver.

REMINDER: Each antenna port on a dual antenna receiver is associated with specific camera channels. One antenna communicates with odd numbered channels (1, 3, and 5), while the other antenna communicates with even numbered channels (2, 4, and 6). See the table below for dual antenna channel configurations.

If you connect the Omni-Directional Antenna to an antenna port and your wireless signal does not improve, try switching the Omni-Directional Antenna to the other antenna port or pairing your camera to a different camera channel.

Scenario 4: Extend the range of all cameras paired to a dual antenna receiver

To extend the range of all cameras on a dual antenna receiver, connect an Omni-Directional Antenna (ACCANTO8) to each antenna port on the receiver.

IMPORTANT: Two Omni-Directional Antennas are required to accommodate this setup.

Combination 1: Combine two Directional Wireless Panel Antennas

If you are using a Directional Wireless Panel Antenna (ACCANTD9) to enhance the signal of a single camera with a single channel receiver, you can use an additional Directional Wireless Panel Antenna to further enhance the wireless signal.

Connect one Directional Wireless Panel Antenna directly to the camera and one Directional Wireless Panel Antenna directly to the wireless receiver. To maximize signal strength, it is recommended to aim the two antennas directly at each other with a clear line-of-sight.

Combination 2: Combine a Directional Wireless Panel Antenna with an Omni-Directional Antenna

If you are using an Omni-Directional Antenna (ACCANTO8) to enhance the signal of multiple cameras, you can further enhance the signal of a specific camera by connecting a Directional Wireless Panel Antenna (ACCANTD9) directly to the camera.

A clear line-of-sight between the Directional Wireless Panel Antenna and the Omni-Directional Antenna is recommended to maximize signal strength.

Lorex SD Pro App: Changing / resetting the password

If the password for the Lorex SD Pro app to view the Wireless Home Monitor is lost or forgotten it will need to be reset.

To reset the Lorex SD Pro app password:

1.Ensure that your Wireless Home Monitor is connected to a network router using the included Ethernet cable.

2.On the Wireless Home Monitor tap the Menu icon ().

3.Use the joystick to select Settings > Network > Reset Password.

4.Select Yes to confirm.

5.Tap the Menu icon () repeatedly until all the menus are closed.

6.Launch the SD Pro app and enter the default password. Refer to your user manual for your default password. You will be prompted to create a new password.

Lorex SD Pro App: Setting up Wireless Home Monitor remote access

You can access and view wireless cameras from a Wireless Home Monitor system using an iPhone, iPad, or Android smartphone or tablet using the Lorex SD Pro app. It is available at the App Store or Google Play Store.

Prerequisites:

To set up the mobile application:

LW2700 Wireless Home Monitor: Included cables and accessories

LW2700 Series Wireless Home Monitors support wireless cameras using a wireless signal. They do not have an internal battery and require a connection to a power source. Refer to your user manual for model specific information on cables and accessories. Click here for downloads and documentation for your product.

Most wireless home monitors include the following cable connections and accessories when purchased:

Network: Wireless camera Internet requirements

Standard wireless cameras that connect to a DVR / NVR, do not need access to the Internet to function. Stand-alone IP cameras do not require an Internet connection for basic functions, but an Internet connection is required for full functionality.

Security Cameras: Understanding Field of View (FOV)

Field of View (FOV) is the maximum observable area that is seen at any given moment through an optical device such as a camera lens. The coverage of the area can be measured using the horizontal and vertical distances to find the diagonal of the area in degrees. Mathematically, the FOV is calculated using the horizontal dimension of the sensor (h) and the Focal Length (F).

You can find the camera’s Field of View details in the Specifications sheet. Click here for additional support content including security camera documentation.

The Camera Lens, Sensor and Focal Length

Focal length (F) is the distance between the center of a lens and its sensor. The size of the lens is the aperture size.

These factors affect field of view. A narrower focal length captures more of the scene and displays a larger field of view. A wider focal length magnifies a scene and decreases the field of view. The higher the focal length value the lower the FOV.

Types of Camera Lenses

Fixed: a fixed camera focal length provides an Angular FOV which is permanently set and cannot be adjusted by the user. Varifocal: the camera focal length can be manually adjusted by the user. Generally, this is done manually with screws or dials. At Lorex we have motorized varifocal cameras that allow you to digitally zoom using your phone or NVR without losing details. These lenses provide flexibility and customization for your camera image needs.

The importance of Field of View

A wide angle lens or smaller lenses produce a greater field of view and captures more objects in a scene enhancing your ability to cover larger and wider areas such as foyers, parking lots or warehouses.

A narrow angle lens or larger lenses produce a smaller field of view; capturing a limited area, but the camera quality image improves in detail. These are designed to monitor a specific object, such as cash registers, entrances/exits, hallways or objects of value.

How to Calculate the FOV

To calculate the FOV requires the sensor size and the focal length of the lens: h = Sensor Size F = Focal Length of the Lens

FOV is represented by this equation: FOV = 2tan-1(h) / 2F

Example: h = 4.7mm F = 6mm FOV = 2tan-1(h) / 2F = 2tan-1(4.7)(12) = 2tan-1(0.39) = 2(21.4°) = 42.8°

W482CAD – 2K Wi-Fi Camera : Frequently Asked Questions

The following FAQ article answers many of the general questions about the 2K Wi-Fi Camera with Smart Deterrence (W482CAD). Where applicable, the FAQ includes links to articles where you may find more information.

.

Where do I place my Lorex 2K Wi-Fi Camera?

.

How should I position my Lorex 2K Wi-Fi camera?

When mounting the camera on a wall, make sure of the following:

 Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

.

How do I enable motion detection and person detection?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap  icon to enable Motion Detection.

Note: If motion detection is disabled, general/person/vehicle detection will automatically disable and you will not receive any motion detection notifications in the Lorex App.

.

How do I customize Motion Zones™?

Motion Zones™ allows you to customize your device’s motion detection region. Motion Zones™ screen consists of the following settings:

To set Motion Zones™

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap Motion Zones™.

 For full instructions on how to set customized Motion Zones™, see Configuring Motion Zones™.

.

Why am I receiving so many notifications?

There are a few ways you can lower the number of notifications you are getting.

.

How do I enable Color Night Vision?

1.Lauch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap  icon to disable Auto Night Vision.
Note: Disabling Auto Night Vision will force the camera into Color Night Vision mode. Recommended in low-light conditions.

.

How to activate Two-Step Verification?

1.Launch the Lorex App.

2.Tap Settings.

3.Tap Account Settings.

4.Tap Two-Step Verification.

5.Tapicon to enable Two-Step Verification.

For detailed setup instructions, see Two-Step Verification Setup.

.

How to optimize video quality?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Video Settings.

4.Tap  icon to enable HDR (High Dynamic Range).

Note: Enabling HDR optimizes video picture in high-contrast conditions such as under-lit and over-lit areas.
By default, the video quality is set to High (2x1080p HD).

.

What is Home & Away™?

Lorex App can automatically use your location to manage your notifications when you are at home or away. The app will notify you when you are inside/outside of your set home perimeter.

To start using this feature, navigate to your mobile device settings and enable Location services for Lorex App.

For detailed setup instructions, see Configuring Home & Away™.

.

How do I activate the LED deterrence light when motion is detected?

1.Lauch Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Deterrence Light Brightness.

4.Tap  icon to enable camera’s deterrence light whenever motion or person is detected.

.

How do I remove the 2K Wi-Fi Camera from my account?

1.Launch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Remove Device.

.

How to permanently delete data of 2K Wi-Fi Camera?

Refer to Formatting Device Storage for more information.

.

Does my device support WPA2 or WPA3?

Your device supports Wi-Fi Protected Access 2 (WPA2) which is the industry standard security protocol for Wi-Fi networks. WPA2 offers security against unauthorized access and data interception and is supported by most Wi-Fi routers including those that support both WPA2 and WPA3. It employs Advanced Encryption Standard (AES), an encryption mechanism, which secures communication between your camera and Wi-Fi network to keep transmitted data confidential. For information on which devices support WPA2 and which devices support WPA3, please refer to “WPA2 and WPA3 Supportive Devices.”

.

What are the compatible SD cards?

Refer to Compatible SD Cards and Storage Sizes for more information.

.

What devices are compatible with the 2K Wi-Fi camera?

Refer to Product Compatibility Chart for more information.

W482CAD – 2K Wi-Fi Camera : Installation

This article provides instructions to install your Lorex 2K Wi-Fi camera with Smart Deterrence (W482CAD).

.

What is included in the box?

The above contents are based on one camera.

.

How to connect with Lorex App

3.Open the Lorex App app and create an account or login with your credentials.

4.Tap  icon to add a new device, then follow the in-app instructions to complete the device setup.

For full instructions on Lorex App setup, see Connecting with Lorex App.

.

How to mount 2K Wi-Fi Camera to the wall

.

How to mount 2K Wi-Fi Camera to the ceiling

Wi-Fi Security Cameras – How to Read a MicroSD card

To view the contents of a MicroSD card on a laptop or computer, follow these steps:

a. Select the day to play back:

b. Click on the available folder:

c. Within the folder, click either the day folder (Video files) or the jpg folder (Snapshots):

d. Click to select a video time from 00 – 23 hours:

6.Click the MP4 video file to view the video. 

Wireless Home Monitor: Audio not working

If the audio is not working on your Wireless Home Monitor:

• Ensure that the protective film is removed from the camera lens.

• Ensure that the monitor volume is not muted. A mute icon () will be visible on the screen if the volume has been muted.

• Turn the monitor volume up using the volume buttons on the side of the unit. Location will vary by model. For exact location of volume buttons for your model, refer to your user manual. Click here for downloads and documentation for your product.

• The camera must be in Full Screen mode for audio. Tap the Channel Select icon () to switch between channels in Full Screen mode. Audio is disabled in Quad mode.

If audio is not working after increasing the volume and viewing in Full Screen mode, restore the system to default settings.

To restore your monitor to default settings:

CAUTION: Restoring to default settings will erase any setting input on the monitor. Your monitor will need to be reconfigured.

1.On the monitor tap the Menu icon ().

2.Use the joystick to select Settings > Default Settings.

3.Select Yes.

.

<p>The post Lorex Wireless Cameras and Monitors guide 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Regardless of your budget, there’s an outdoor security camera that’ll fit your needs. From premium products crafted by Ring to budget-friendly options like those from Wyze, there are dozens of well-reviewed models that are perfect for protecting your home.

In fact, some of the best outdoor security cameras also double as floodlights –- allowing you to light up your yard. Others are wireless for easy installation, while a handful require wired connections (though this allows for continuous monitoring).

Below, you’ll find a list of the best outdoor security cameras of 2023. You can’t go wrong with any of them, but each one caters to a specific audience and budget, so take a closer look at each to figure out which is best for your home.

John Velasco / Digital Trends

Arlo Pro 4

Best outdoor security camera

.

The Arlo Pro 3 was our pick for the best outdoor security camera for some time, but after testing the Arlo Pro 4, it brings a couple of new additions that help it earn our top pick. Just like its predecessor, it packs 2K video resolution and a wide 160-degree viewing angle. Also included are a weatherproof camera with color night vision, a built-in LED spotlight, and a built-in siren that can alert you to danger.

What makes this model superior is the fact that it no longer is tethered to a hub in order to talk with your home’s Wi-Fi network. You won’t need it this time, which certainly streamlines the setup process. And best of all, not only does it perform as exquisitely as the Arlo Pro 3 when it comes to safeguarding your home, but it now boasts a lower starting cost of $200 for a single camera, whereas the Arlo Pro 3 started at $500 for a 2K camera system.

The Arlo Pro 4 includes a three-month free trial of Arlo Smart, which gives you access to advanced features like 30 days of recording history, activity zones, enhanced 911 calling, and advanced detection features.

John Velasco / Digital Trends

Wyze Cam v3

Best outdoor camera for night vision

.

Night vision is a vital feature for every outdoor security cam — you don’t want the darkness to hide any detail, especially if something like a break-in happens. While our top cam picks include various kinds of night vision, Wyze’s indoor/outdoor cam is particularly notable thanks to its Starlight Sensor, which can record night-time video in full color for users.

This wired cam includes all the other smart features that make Wyze’s cams a great pick, including a motion and sound sensor for alerts, detection zones, sensitivity settings that you can tweak for best results, and two-way audio for communication. It’s also compatible with Alexa and Google Assistant and is friendly with IFTTT if you’d like to set up complex routines based on the alerts the cam gives you.

The Wyze Cam v3 also has one of the best free video storage options around, with a 14-day cloud storage option for video clips at zero cost. There’s also an SD card slot for local storage if you prefer that method. While it’s an indoor/outdoor cam, you don’t need to worry: All the outdoor IP65 resistances are included for all types of weather.

Image used with permission by copyright holder

Lorex Dual-Floodlight V261LCD-E

Best outdoor camera for cold weather

.

You don’t need to worry about winter temperatures with this model, thanks to its IP65 rating that can endure -40 degrees Fahrenheit, suitable for even the coldest winters in the country. It also has particularly bright, 2,000-lumen, dual-LED floodlights (excellent for illuminating a large area at night) that can be triggered by motion cams. App controls also allow you to set manual start times and schedules for the lights.

That’s just the start of what this winter-ready Lorex cam can do: It also includes a two-way audio option, compatible with Alexa and Google Assistant devices, and the expected motion alerts for your phone. There’s no subscription plan or cloud sharing for this cam. Instead, it comes with a 32GB microSD card and port for free native storage. You can upgrade the model up to a 256GB card for extra space, which may be a good idea if you put the camera in a place that’s difficult to reach without a ladder, such as above a garage.

Best outdoor security cameras 2023

Read More : The 10 Best Video Management Softwares (VMS)

Image used with permission by copyright holder

Ring Spotlight Cam Pro

Best wireless outdoor security cam

.

Amazon’s update to the Ring Spotlight Cam is an excellent option for those who don’t want a full floodlight camera, but would still like lots of illumination for their porch, patio, or driveway. The surprisingly bright LED lights on either side of the cam can be set to light up along with the motion detection features.

There’s a little bit of everything packed into the Spotlight Cam Pro’s design, including basics like 1080p video, night vision, and two-way audio. But Ring also has some extras, like a siren you can sound, advanced 3D motion detection, and a “Bird’s Eye” view option that gives you a model for where a subject may have gone. We also like that it’s battery-powered with an option to plug into an outlet.

As with all Ring cams, you will really want a Ring Protect plan to enable video storage and video sharing, but otherwise, this is the most comprehensive wireless security cam we’ve seen to date.

Google

Google Nest Cam 2nd-gen (battery)

Best value security camera kit

.

Google’s Nest Cam benefits greatly from Google’s AI technology that can recognize people from cars, identify packages, and (with a subscription) do much more. While there is a wired version of this cam, we like the battery option for its versatility. We also love that it’s one of the few cams that offer free online video storage – three hours worth – for free, although a Nest Aware subscription does add other benefits.

Nest works with both Google Assistant and Alexa these days, so you don’t have to worry as much about which voice assistant you use. The cam itself is highly capable, with 1080p HDR video, night vision, zoom, two-way audio, and a variety of intelligent alerts. The snap-on mount is also a great way to make installation easy, no matter where you’re putting it. There’s even a feature to keep recording when the power goes down and save an hour of footage into local memory for review.

If the battery option isn’t really your thing, you do can purchase a weatherproof outdoor cable and wire the cam into place as well.

Arlo

Arlo Pro 5S 2K

Best premium outdoor security camera

.

The Arlo Pro 5S 2K doesn’t cut any corners. Featuring a camera that captures 2K video, a wide field of view, sleek design, and color night vision, few products can match its performance. Unfortunately, all those features come at a price, as the Arlo Pro 5S 2K clocks in at $250.

That makes it one of the most expensive security cameras on this list, but if money is no object, it deserves a closer look. Not only does it offer every feature found on our beloved Arlo Pro 4, but it also features Dual-Band Wi-Fi for simplified installation, SecureLink Connectivity that allows it to stay protected during power outages, and a Low Power Mode that offers a 30% boost to battery life.

But beyond those features, it’s eerily similar to its cheaper sibling. Still, if you need an outdoor security camera that’s as cutting-edge as possible, you can’t do better than the Arlo Pro 5S.

Image used with permission by copyright holder

Blink Wired Floodlight Camera

Best affordable floodlight camera

Blink makes plenty of great outdoor cameras, but few are as great as the Blink Wired Floodlight Camera. As one of the newest members of the Blink family, the Wired Floodlight Camera offers heaps of functionality despite its budget-friendly price of $99.

In case the name didn’t give it away, the Blink Wired Floodlight Camera isn’t just an outdoor camera – it’s also a floodlight. And a bright one at that, capable of producing 2,600 lumens of LED light. You’ll also benefit from motion detection, a wired connection that offers a constant power supply, and color night vision. Its design is a bit bulkier than others on this list, but that’s largely due to the massive floodlights that loom over the camera.

Anyone in the market for an outdoor camera that’s both affordable and powerful (and comes with shockingly bright floodlights) should give strong consideration to Blink’s new product. But if you’re looking for something with a more streamlined design, consider looking back at the Ring Spotlight Cam Pro mentioned earlier in our roundup.

Wyze

Wyze Cam Floodlight Pro

With the ability to capture 2.5K QHD footage and built with three adjustable floodlights that product 3,000 lumens of brightness, the Wyze Cam Floodlight Pro is a premium camera that doesn’t carry a premium price. It’s best for capturing large backyards or driveways (thanks to its powerful floodlights), but they can also be dimmed if you don’t need quite as much power.

Rounding out the package is automation that senses when the sun goes down, support for microSD cards to store footage locally, two-way audio, and compatibility with Alexa, Google Assistant, and IFTTT. Because it’s a floodlight, it’s a bit bulkier than most other products on this list, but it’s a great option if you like the idea of filming in 2.5K QHD and want to light up your yard when motion is detected.

Blink

Blink Outdoor 4

The Blink Outdoor 4 takes everything you loved about the Outdoor 3 and makes it even better. The two-year battery life is still here, but you’ll also benefit from a new 143-degree field of view, enhanced motion detection (including person detection), and improved night vision.

As usual, you’ll need to spring for a Blink Subscription Plan to access everything the camera has to offer, but since plans start at just $3 per month, it shouldn’t be a dealbreaker. Toss in a new design, a robust smartphone app, and full support for Alexa, and the latest member of the Blink family is mighty enticing.

Phil Nickinson / Digital Trends

Ring Stick Up Cam Pro

It’s a bit expensive, but you’re getting a lot of value out of this investment. The Ring Stick Up Cam Pro is designed to work both indoors and outside – giving it plenty of versatility. Along with its weatherproofing, the camera offers HDR video and films in 1080p, supports two-way audio, and is easy to install thanks to its wire-free setup.

One minor sticking point is its lack of a built-in privacy shutter. That might be an issue if you’re using it indoors, though you can quickly toggle alerts off and disarm the camera from the Ring smartphone app. But if you have it installed outside, you likely won’t miss the feature. You’ll also want to spring for a monthly Ring subscription to unlock additional features such as cloud saves and smart alerts.

Beyond those minor quirks, there’s not much to dislike about this powerful outdoor camera. Homes with other Ring products already installed will love how easy it is to sync the device with the rest of their smart home, and Ring newcomers will enjoy its high-quality images, simple setup, and generous 155-degree viewing angle.

Arlo Essential XL

The Arlo Essential XL Wireless Security Camera is all about battery life. Capable of running for up to 16 months before needing a recharge, it’s leagues beyond most other products on the market. That makes it incredibly appealing if you’re using it on a second property or plan to put it in a place that’s cumbersome to reach (as you’ll only have to take it down less than once per year).

It also benefits from support for 2K footage capture, color night vision, and a wide 130-degree viewing angle. You’ll likely want to pick up an Arlo Secure subscription so you can get improved smart alerts and 30-day video history – though it’s a bit more expensive than the competition at $5 per month.

The Essential XL is fully supported by the Arlo smartphone app, meaning you can easily set activity zones, view your alert history, or check out a live feed of your camera. And despite all these great features, the Essential XL is reasonably priced. To save even more cash, you can opt for the HD version, which offers all the same features, but ditches the 2K resolution for standard HD.

Frequently Asked Questions

Where do I place outdoor security cameras?

FBI crime data indicates that most (around 55%) home intruders try to get into homes through either the front or back door. So, you may want to have your security camera scoping out your doors. It’s also a good idea to cover other entry points, like back windows, that are hidden away where someone could break in without being seen.

Where exactly to mount your outdoor cameras, however, depends on your property and your individual needs. You may have a shed in the back that contains expensive lawn equipment, for instance, and you might want to place more focus on that area. Perhaps your neighborhood has experienced a few break-ins recently, and the intruders typically enter through the garage, so you want to cover your garage area.

How many security cameras do I need?

Typically, having at least two outdoor cameras is ideal, not including your video doorbell. If you have a video doorbell to watch your porch, combined with an outdoor security camera covering the front and back areas of your home, this should be sufficient. However, if you have a large property, live in an area where there’s a lot of property crime, or if you have vehicles or valuables stored on your property, you may want to add in an extra camera or two.

Can you use an indoor security camera outdoors?

No. An indoor camera does not have the necessary protection from the elements, so it won’t hold up outside. Some cameras are rated for indoor or outdoor use, and you can use those cameras outside. If you want to point your indoor camera out a window to watch the outdoors, you technically can do so. However, the camera’s features probably won’t work as well, and you’re better off just buying a cheap outdoor camera.

Can outdoor security cameras be used indoors?

Yes, although it’s not usually recommended because the cameras designed for outdoor use may not work optimally indoors. Again, you can opt for a camera that’s rated for both indoors and outdoors, like a dome camera.

Do all outdoor security cameras have two-way audio?

The short answer is no. Many wired outdoor cameras feature two-way audio, which allows you to speak back and forth with someone through the camera via an app on your phone, but not all outdoor cameras have this feature.

If two-way audio is something you’re interested in, consider doing research on which cameras have it, and of the ones that do, read up on which are better. Not all two-way audio is created equal — some companies do it well, while others do not. Keep in mind that cameras with two-way audio might cost a bit more than those that don’t feature the technology.

How well does night vision work on an outdoor security camera?

Night vision on cameras typically uses infrared light to illuminate dark images at night. Essentially, cameras with night vision use this technology to backlight images to help you see what’s happening in the field of view. Most outdoor security cameras feature night vision, but the quality varies from model to model.

If you’re looking for superior night vision, go for the Arlo camera listed above, or research night vision quality before making a purchase.

How well do outdoor security cameras detect motion?

Motion sensitivity in outdoor security cameras varies widely, but generally, the technology works well regardless of the model you choose. Most cameras, even inexpensive ones, do an excellent job of detecting motion, and, if the camera is connected to an app, it will send a motion alert to your phone. Most people find that motion settings on cameras are too sensitive, meaning that things like rain, bugs, or even bright sunlight can trigger an alert.

If you’re concerned about motion alerts, consider buying a camera that not only sends you motion alerts so you can monitor what’s happening on your property but also allows you to adjust the motion sensitivity so that small things aren’t triggering it all the time.

Can outdoor security cameras survive severe weather?

Most outdoor cameras have a rating of IP65 or higher, which means they are waterproof and can withstand someone spraying a hose on them. That usually (but not always) means that a camera with that rating can withstand extreme temperatures ranging from -40 to 110 degrees Fahrenheit or similar.

Cameras vary slightly in terms of survival in extreme weather, but anything with a rating of IP65 or higher will be fine for most climates. If you live in an extremely hot or extremely cold climate, you might want to consider a camera with a rating of IP66 or higher.

Do I have to pay for storage for an outdoor camera?

This depends a lot on the brand and the model. Generally, if a security cam has a memory card slot, you can use native storage without paying anything — it’s just a little trickier to manage. If you want video footage to be uploaded to the cloud for easier viewing and saving, you’ll often have to pay for it. Brands like Arlo and Ring only allow for free livestreaming video and require a plan if you want to save video for any length of time. Google is one of the best options here because its Nest cam offers a certain amount of free online storage without needing a subscription.

Is an outdoor security camera ever illegal?

It can be, although privacy laws haven’t entirely caught up with home security cams yet. Generally speaking, you can’t point a camera where people have the expectation of privacy. Pointing a cam at your porch and the street in front? Totally fine, it’s considered a public area. Pointing a camera so that it captures footage of your neighbor’s backyard or looks into their windows? Illegal, and you could get successfully sued for it.

.

<p>The post Best outdoor security cameras 2023 first appeared on NVR IPCAMERA SECURITY.</p>

Reolink NVR Setup Guide, Use this NVR with Reolink PoE cameras and you can get a professional, reliable and DIY security camera system. You can play back any recorded video, back up local data, and do more. For more features, refer to RLK8-810B4-A NVR security system.

If you have ordered an RLN8-410 or are interested in it, and want to get some basic information about this product before placing it in use or placing the order, you may refer to the below introductions.

This article includes the following 4 parts which will help you quickly understand the use and working principles of the NVR:

Unboxing for RLN8-410

Product Overview

You may find detailed information about the structure and components of the NVR below. 

Installation

You can connect either hard-wire the PoE cameras or connect WiFi cameras wirelessly (except for battery-powered cameras) to the NVR. Below is a common network topology of the connection. 

For more instructions on the configurations, you may refer to the sections Wired Connection and Wireless Connection. 

Wired Connection

Applies to cameras that are hard-wired to the NVR. 

Step 1. Connect your Reolink IP cameras to the Reolink PoE NVR. 

Step 2. Log into your NVR, and go to the IP channel.

Old UI: 

New UI:

Step 3. Select Auto Add so that all the cameras in the same LAN can be automatically shown on the list.

Step 4. If you have never changed the password of the IP cameras (the default password of the IP camera is blank) and there are enough channels for all the cameras, you may press Apply to add all the IP cameras to the NVR.

Step 5. If you have changed the User Name and the Password of your cameras, please put the password of the camera to log in.

Old UI:

Please drag the menu bar to the password column and use the soft keyboard to input the required information.

New UI:

Please click Modify to input the required information.

Step 7. Click Apply to save and apply the configuration.

For more detailed instructions, you could refer to the articles below:

Reolink NVR Setup Guide

Read More : Reolink NVR IPCAM how to reset password methods

Wireless Connection

Applies to wifi cameras (except for battery-powered cameras) attempting to add to the NVR. 

Step 1. Connect the WiFi camera to the same LAN as the PoE NVR.

Step 2. Connect the camera to the WiFi of the router. 

Step 3. Add the camera to the PoE NVR: Toggle the “Auto add” on and hit “Modify” to input the login credentials. 

Old UI:

New UI:

For more details of the configurations, please refer to the links below: 

Initial Setup

You can do the initial setup on a monitor or TV connected with an HDMI/VGA cable, or through the Reolink App or Reolink Client.  

Step 1. Connect the NVR to a Monitor or TV via the VGA or HDMI cable.
Step 2. Connect the camera’s RJ45 network socket to any PoE Camera port on the NVR using the Ethernet cables provided.
Step 3. Connect an Ethernet cable from the LAN port of the NVR to the LAN port of your router.
Step 4. Connect the mouse to the USB port.

Step 5. Connect the Power Adapter. Please use the supplied power adapter. For the PoE NVR device, it is 48 volts.
Step 6. And then you will see the below splash screen. System booting up might take a few seconds.
Step 7. Follow the Setup Wizard to set your NVR, click Next to continue and at the last step, click Finish to save all the settings.
For more detailed instructions, you may refer to the articles below:
.

Step 1. Power the camera and the NVR, then launch the Reolink App on your phone.
Step 2. During start-up, you will find the NVR shown on the Delive List automatically on Reolink App.

Step 3. Click the device you want to add to start initialization.

Step 4. For security considerations, you need to create a password for the first time.
Step 5. Then name your device and modify other settings on the second step page.
For more detailed instructions, you may refer to the article: How to Do Initial Setup for Reolink NVR via Reolink App.

Step 1. Click the “+” icon, select UID, then fill in the blanks with the UID number of your NVR, See How to find the UID of your device.

Step 2. Create a device password, then click Next.
Step 3. Create a device name then click Finish.
For more detailed instructions, you may refer to the article: How to Initial Set up NVR via Reolink Client (New Client).

.

How to Add Reolink Cameras to Reolink PoE NVR

Reolink PoE NVR allows you to record videos for Reolink IP cameras without using a computer. To do that, you need to add the camera to the NVR first. The cabling for PoE NVR is shown below.

Applies to: All Reolink IP cameras (excluding battery-powered cameras) and PoE NVRs with the hardware version H3MB02/H3MB16

You may then follow the steps below to add Reolink cameras to Reolink PoE NVR.

Step 1. Connect your Reolink IP cameras to the Reolink PoE NVR. There’re two different ways of powering your IP cameras:

There are two ways of connection:

 a. Connect the PoE cameras to the PoE NVR directly via an Ethernet cable. (suggested way)

 b. Alternatively, you can power on this camera by a PoE switch/injector and connect to your router, then add this camera to the POE NVR system in the same local network.

All Reolink WiFi cameras (except for battery-powered cameras) can be used with Reolink PoE NVRs, too. You need to connect them in LAN, the connection diagram is as below:

Note: Make sure all the IP cameras you want to add to the NVR are connected to the same network (LAN) as the NVR. Otherwise, the cameras won’t be shown on the scanned list and cannot be automatically added to the NVR.

Step 2. Log in to your NVR, and go to the IP channel.

Step 3. Select Auto Add, and click Scan so that all the cameras in the same LAN can be automatically shown on the list.

Note: The number of cameras that can be added to the NVR may vary depending on the NVR channel numbers of the NVR.

Step 4. If you have never changed the password of the IP cameras (the default password of the IP camera is blank) and there are enough channels for all the cameras, you may click Apply to add all the IP cameras to the NVR.

However, if you have changed the login passwords of the IP cameras or there is no spare channel to display all the IP cameras, you may need to go through a few more steps.

Step 5. If you have an 8-channel NVR and more than 8 IP cameras, please choose the 8 of them you want to add to the NVR and manually change the other cameras’ Channel to None.

Note: You may assign the IP cameras to any channel you want, but you cannot have two cameras on the same channel, otherwise configurations would fail to be saved.

Step 6. If you have changed the User Name and the Password of your cameras, please drag the menu bar to the password column and use the soft keyboard to input the required information.

Step 7. Click Apply to save and apply the configuration.

Here is a video to show how to add WiFi cameras to PoE NVR:

Note:

RLN8-410 (with the hardware version H3MB02) and RLN16-410 (with the hardware version H3MB02 and H3MB16) don’t work with 8MP cameras including B800/D800. The 4k cameras can only work with RLN8-410-E (with the hardware version H3MB16 and H3MB18) and RLN16-410 (with the hardware version H3MB18). And only the RLN8-410(H3MB18, N3MB01) and RLN16-410 (H3MB18) support the Human/Vehicle detection function.

.

How to Initially Set up Reolink NVRs with Monitor Connected (New UI)

Want to do the initial setup for Reolink NVRs on a monitor? This article will do you a favor.

Applies to: RLN8-410 (hardware version H3MB18/N2MB02/N3MB01/N7MB01), RLN16-410 (hardware version H3MB18/N6MB01), RLN36.

You may follow this guide for proper cabling and initial setup of your Reolink NVRs with a monitor connected.

Here is a video for your reference:   

Here is a diagram that will help you learn each option on the PoE NVR.

Now, please refer to the following steps to set up your NVR.

Step 1. Connect an Ethernet cable from the LAN port of the NVR to the LAN port of your router. And connect a mouse to the USB port.

Note: You can right-click to open the Menu on the live-view page.

Step 2. Connect the NVR to a Monitor or TV via the VGA or HDMI cable. 

Notes:
1. If there is no display, please connect it to a VGA monitor and change its resolution to 1920*080.
2. If you need audio output on your TV monitor, the resolution MUST be set to 1920*1080 or 1280*720.

Step 3. Connect the camera’s RJ45 network socket to any PoE Camera port on the NVR using the Ethernet cables provided.

Step 4. Connect the NVR to a power outlet with the supplied power adapter, and then turn on the power switch.

Step 5. And then you will see the below splash screen. System booting up might take a few seconds.

Note: If the monitor screen remains black, check if you flip on the power switch on the back of the NVR.

Step 6. General configurations. Set up the language, screen resolution, date Format, and time format. Then click Next.

Step 7. DST settings. Set up the system time and time zone, and enable/disable the DST option. Then click Next.

Step 8. Create a password for your NVR, and enable/disable screen auto-lock. Then click Next.

Step 9. Set up a password security question. Then click Next.

Step 10. Name your device and manage your HDD. Then click Next.

Step 11. Configure the network for your NVR. Then click Next.

Step 12. Set up E-mails for your NVR up to your need. Then click Next.

Done! Here is a sum-up of the Wizard Setup.

Troubleshooting for RLN8-410

Here are some troubleshooting tips for RLN8-410. You may check whether your camera’s issue is listed below. If not, you may go to the Troubleshooting section to find suggestions for more issues or you may contact Reolink support for help.

If the NVR stops working and the power LED is not on, you may follow the troubleshooting tips listed below to solve the problems.

Cause 1. Power adapter issue

Solution: Check the status LED on the power adaptor of the NVR. If the LED isn’t on, please plug the power adaptor into another socket as well as change another working power adaptor (48V) for a try. If the LED is on, please check the HDD issue below.

Cause 2. HDD issue

Solution: Please unplug the HDD and check if the NVR will power on when no HDD is plugged in. You may open the NVR housing and refer to How to Change the HDD for Reolink NVR to remove the HDD. 

Cause 3. The voltage is not sufficient.

Solution: Unplug the cameras. If the NVR power LED goes on, please replug the camera back one by one. 
For more information, please check POE NVR Failed to Be Power on.

When you connect the NVR via a monitor and start up the NVR, the NVR is freezing on the Reolink Logo Page. There are several possible causes for the issue. You may follow the troubleshooting tips listed below to solve the problem. 
.

Cause 1. HDD issue

Solution: Please unplug the HDD and check if the NVR will power on when no HDD is plugged in. You may open the NVR housing and refer to How to Change the HDD for Reolink NVR to remove the HDD.

Cause 2. The voltage is not sufficient. 

Solution: Unplug the cameras that are connected to the NVR and check if the NVR can boot up.

Cause 3. Firmware issue

Solution: Please refresh the firmware using a USB drive. 

For more details, please check the article NVR is Freezing on the Reolink Logo Page.

If there’s no video output on the monitor from Reolink NVR, you may follow the troubleshooting tips listed below to solve the problem. There are several possible causes for the problem.
.

Cause 1. The video output resolution of the NVR is not supported by the monitor/TV. 

Solution: Ensure that the lowest resolution of the TV/monitor is no less than 720p.

Cause 2. HDMI/VGA port on the NVR or the monitor/TV is defective. 

Solution: Check whether the cable is defective by using it to connect other devices to the router and see if it works. Or please test with another HDMI/VGA cable or monitor/TV. 
For more information, please check the article No Video Output on the Monitor/TV from Reolink NVR.

If you found that the NVR is rebooting, below are some possible causes and solutions that you may refer to. 

Cause 1. UPS issue

Solution: If you use the UPS to power the NVR on, please plug the NVR directly into a wall socket and have it run for one or two days then check if the NVR reboots.

Cause 2. HDD issue

Solution: Please unplug the HDD and have the NVR run for one or two days then check if the NVR reboots. 

Cause 3: The cameras and the NVR are both grounded. 

Solution: Please unplug all the cameras from the NVR and have the NVR run on its own for one or two days and check if it still reboots (Please disable auto-reboot before you run the test). If the NVR doesn’t reboot, the issue may be caused by both the NVR and the cameras being grounded. Please check whether the cameras and the NVR are grounded. If yes, please unground either the NVR or the cameras to fix the issue. 

For more details, please refer to POE NVR Reboots Automatically.

If you noticed that after plugging the new cameras into the NVR, the camera’s image does not show up on the monitor and it prompts “video loss”. The following troubleshooting may be helpful to you.

Cause 1. No available channels

Solution: Delete the offline cameras from the IP channel, or manually assign a channel for the camera. 

Cause 2. The new camera is distributed with the same IP address as the other cameras. 

Solution: Please reset the camera and restore the NVR.

Cause 3. The camera shows “invalid password” or “incorrect username and password”. 

Solution: Put the password of the camera.

For more details, please refer to Fail to Add PoE Cameras to NVR.

If you fail to connect the NVR through the network, below are some possible causes and solutions for your reference.

Cause 1. NVR is powered off. 

Solution: Check whether the power light is on. If it is off, please refer to POE NVR Failed to Power on.

Cause 2. The LAN port is defective. 
Solution: Please check if the LAN port on the back lights up or not. If not, please try another ethernet cable and port on the router for a test.
Cause 3. The gateway is 0.
Solution: Please change a router or switch and further check the issue. Please also reboot the NVR and check if the issue remains.

Please upgrade the NVR’s firmware to the latest firmware.

For more details, please refer to Failed to Connect NVR in LAN.

When you fail to playback the videos of the NVR and find the capacity of the HDD is 0GB, or it shows “HDD not detected”, here are some possible causes for your reference.
.

Cause 1. The firmware version of the NVR is old. 

Solution: Please find out the firmware version of the NVR and go to the Download Center to download and unzip the package to upgrade it. 

Cause 2. The format of the HDD is wrong. 

Solution: Please format/init the HDD to try again, please refer to Check/Init HDD via PoE NVR.

Cause 3. Defective HDD

Solution: Please unplug and replug the HDD to see if it works. If possible, please test with another working HDD. 

For more details, please refer to HDD Capacity Shows 0GB.

.

Configuration – RLN8-410

RLN8-410 is an eight-channel network video recorder that is used for centrally controlling the devices that are connected to it. With diffenernt hardware versions, RLN8-410 can acheive different features. Generally, it can be used for setting up detection for the cameras, managing the channels, upgrading the devices that are connected, etc. 

To better learn the working principles and settings of this NVR, here are some instructions for your reference.

Note: You can click on the keywords below to jump to the corresponding section.

Motion Detection

Generally, Reolink cameras are capable of motion detection. RLN8-410 is able to manage the configurations of motion detection for cameras that are connected to it. 

To achieve the detection settings you want, you could try on the monitor, the Reolink App, or Reolink Client. Below are some instructions for your reference. 

Old UI: 
1. Log into your NVR on a monitor and go to the NVR settings. 
2. For configuring motion recording, go to “Menu>Recording>Schedule” page, then select the channel (camera) and check the Enable box. Select “Motion” and tap on the grids to choose the time that you want to enable motion detection recording, and then click Apply to save the settings.

3. For setting up motion detection, go to “Menu>Alarm”. Click on “Motion Detection>Set”, then you can configure the motion detection settings (including motion detection area and sensitivity), motion schedule, and action.

For more details, please refer to:
How to Set up Motion Detection Recording via Reolink PoE NVR
How to Set up Motion Detection Area via Reolink PoE NVR
How to Set up Motion Detection Sensitivity via Reolink PoE NVR

New UI:
1. For setting up motion recording, log in to your Reolink PoE NVR on a monitor. Go to “Menu>Surveillance>Daily Schedule” page.

2. For setting up motion detection for cameras, go to “Settings>Camera>Detection”. 

For more details, you may refer to the articles below:
How to Set up Motion Detection Recording via Reolink PoE NVR (New UI)
How to Set up Motion Detection Area via Reolink PoE NVR (New UI)
How to Set up Motion Detection Sensitivity via Reolink PoE NVR (New UI) 

1.Click  button to go to Device Settings>Channel Setting>Motion Detection.

.

For more details, please refer to:
How to Set Motion Detection Schedule for NVR via Reolink APP 
How to Set up Motion Detection Sensitivity via Reolink App 
How to Set up Motion Detection Zones via Reolink App 

.

For more details, please refer to:
How to Set Motion Detection Recording for Reolink NVR via Reolink Client (New Client) 
How to Set up Motion Detection Area via Reolink Client (New Client) 
How to Set up Motion Detection Sensitivity via Reolink Client (New Client) 

Smart Detection

Smart detection includes Smart Person, Vehicle, and Pet Detection. It is based on the traditional motion detection but with advanced algorithms and technology, which can tell people, vehicles, and pets from other objects. You can set up detection sensitivity, detection zone, object size, etc. for the cameras via the NVR. 

Please notice that for 8-channel NVRs, only if the hardware version is N2MB02/N3MB01 can it achieve the smart detection settings.
To check the version of your NVR, you can refer to How to Find out System Information via Reolink App or contact Reolink Support Team for confirmation. 

On Monitor

1. Please go to the Menu of your NVR, and go to “Surveillance>Record>Daily Schedule”.
2. Under the Record Schedule page, please choose the camera model/channel you want to set up the record schedule. 
3. Under the Alarm schedule, please enable/choose the detection type and then enable the time & date for detection.

There are three detection types: ” Any Motion”,” Person” and ” Vehicle”. Please enable/choose either of them or combine two options or all of them together according to your own needs.
For more details, you may refer to the articles below:
How to Set Smart Detection via the PoE NVR System (New UI) (Video)
How to Set up Smart Person/Vehicle Detection via POE NVR system
How to Set up Smart Person Detection only via Reolink POE NVR System 
How to Set up Vehicle Detection only via Reolink PoE NVR System 
How to Set the Maximum and Minimum Object Size via POE NVR System (New UI) (Video) 

.

On Reolink App

.

For more details, please refer to:

How to Set up Smart Person/Vehicle Detection via Reolink APP  
How to Set up Smart Person Detection only via Reolink APP 
How to Set up Smart Vehicle Detection only via Reolink APP 

.

On Reolink Client

.

For more details, please refer to:
How to Set up Record Schedule via Reolink Client (New Client) 
How to Set up Smart Person Detection only via Reolink PC Client 
How to Set up Smart Vehicle Detection only via Reolink PC Client 

.

Buzzer

Buzzer includes motion buzzer and exception buzzer. It is the sound that comes from the NVR when the cameras detect motions or the NVR detects abnormalities. Conditions like HDD full, HDD error, network disconnected and IP conflict will be marked as exceptions.

You could set up motion buzzer via the monitor, Reolink App, or Reolink Client. Please notice that the exception buzzer can only be set up via the monitor.
Below are some basic instructions for your reference. 

Old UI:
1. Set up Motion Buzzer:
Go to “NVR>Menu>Alarm>Motion>Action”, and tick Buzzer for selected cameras (channels). Click Apply to save the settings.

2. Set up Exception Buzzer:
Go to “NVR>Menu>Alarm>Exception”, select the exception type you want, and tick Buzzer then click Apply to save the settings. Choose the Type for the exception alarm based on your requirement.
For more details, please refer to:
How to Set up Motion Buzzer for PoE NVR
How to Set up Video Loss Buzzer for PoE NVR
How to Set up Exception Buzzer for PoE NVR

New UI:
1. Set up Motion Buzzer:
Go to “Settings>Surveillance>Buzzer”, and enable Buzzer. Then click “Daily schedule” to choose the schedule and detection type.


2. Set up Exception Buzzer:
Go to “Settings>Surveillance>Buzzer (Exception)” and select the exception type you want.

For more details, you may refer to the articles below:
How to Set up Motion Buzzer for PoE NVR (New UI)
How to Set up Exception Buzzer for PoE NVR (New UI) 

1.Click  button to go to Device Settings>Channel Setting>Buzzer. If you want to enable/disable the alarm buzzer, please turn it on/off the Buzzer.
Please notice that this setting will apply to all the cameras connected to the NVR.

For more details, please refer to How to Enable/Disable Alarm Buzzer for POE NVR via Reolink App.

Channel Management

When a camera is successfully connected to the NVR, it will be distributed an IP address and a channel by the NVR for connection. Hence, with the NVR, you’re able to check the status of all the connected cameras at the same time. On the channel management page, you’re able to check the status of each channel/camera, delete the offline devices, arrange channel orders, etc.

Below are some basic instructions that you may refer to. 

On Monitor (Old UI)

1.Launch your Monitor of NVR, go to Menu>IP channel page. Then you will find the camera status in the sidebar of the IP channel page.

2.If you would like to delete the offline cameras, change the Channel of the disconnected IP camera to None and then click on Apply.

3.If you would like to change the display order of the camera, expand the selection bar to assign a channel for each camera. After that, click Apply to save the settings.

For more details, please refer to:
How to Check Camera Status on IP Channel page Via Reolink PoE NVR
How to Delete Offline Camera Information on IP Channel Page via Reolink NVR
How to Arrange the Display Order of Cameras on Reolink NVR 

On Monitor (New UI)

1.Launch your Monitor of NVR, then chooseMenu>Channel>Replace. You will find the camera status in the sidebar of the IP channel page.

2.If you would like to delete the offline camera, click on the offline camera and tap the Delete button to delete it from the NVR. Then the channel this camera was taken is free now.

For more details, please refer to the articles below:
How to Check Camera Status on IP Channel Page via Reolink PoE NVR(New UI) 
How to Delete Offline Camera Information on Channel Management Page via Reolink NVR(New UI) 
How to Arrange the Display Order of Cameras on Reolink NVR(New UI) 

.

Upgrade

As a centralized management system, RLN8-410 is able to upgrade both the NVR and the cameras that are connected to it. Below are some basic steps of upgrading for your reference. 

1.Unzip/extract the firmware file on your PC and transfer the PAK file to a USB, then insert the USB to the NVR USB port. 
Please notice that there are two USB ports on the NVR. One is at the front and the other one is at the back of the NVR. 

2.Log in to your Reolink PoE NVR on an NVR monitor, then go to Device Settings>System>Maintenance page.

3.Choose the correct firmware file and start to upgrade.
*If you only want to upgrade the firmware for the PoE NVR, you may click the Upgrade From USB and select the correct firmware file, then tap on the Upgrade button.
*If you need to upgrade the firmware for cameras that are connected to the PoE NVR, please choose Upgrade IPC From USB, then select the correct firmware for each channel and click on the Upgrade button to start upgrading.

For more details, please refer to How to Upgrade Firmware via PoE NVRs.
For upgrading the NVR only, you can also refer to How to Upgrade Firmware via Reolink Client (New Client).

1.Unzip the firmware file (.pak file) on your PC and transfer it to a USB, then insert the USB to the NVR USB port.

2.Log in to your Reolink PoE NVR on an NVR monitor, then go to Device Settings>System>Maintenance page.

3.Choose the correct firmware file and start to upgrade.

*If you only want to upgrade the firmware for the PoE NVR, you may click the Upgrade From USB and select the correct firmware file, then tap on the Upgrade button.
*If you need to upgrade the firmware for cameras that are connected to the PoE NVR, please choose Upgrade IPC From USB, then select the correct firmware for each channel and click on the Upgrade button to start upgrading.

For more details, please refer to How to Upgrade Firmware via PoE NVRs (New UI).
For upgrading the NVR only, you can also refer to How to Upgrade Firmware via Reolink Client (New Client).

.

<p>The post Reolink NVR Setup Guide first appeared on NVR IPCAMERA SECURITY.</p>

Part 1: How do I install a Hard Drive in a Hikvision NVR?

Any setup with an NVR will need a hard drive to function as it is what all your footage is saved to. The WD Purple Drive is our go-to recommendation for the vast majority of IP setups as it designed with the high workload requirements of 24/7 surveillance solutions in mind. Please see the guide on picking the right HDD to better understand your storage needs and why we don’t recommend using HDD’s that aren’t optimised for use in a CCTV system.

Please see the five simple steps below for getting your hard drive installed into your NVR:
.

.

Step 1:
.

Firstly, you’ll need to locate and remove the screws that secure the NVR’s casing to the base so that you can access the inside of it. Typically, you’ll find two of these screws on the back of the unit and, depending on the NVR model, more on the sides – Do not lose these screws!​

.

.

Step 2:
.

Once inside, your NVR will look something like this. The parts in here you’ll need to identify are the:​

.

.

Now look at your HDD – fewer things to identify here:​

Step 3:
.

Get your hard drive and NVR connected – You can screw the drive into its bay in NVR first if you wish, but it’s normally easier to wire everything up first. Plug one end of the SATA interface cable into the HDD and the other into the corresponding port on the motherboard, then do the same with the SATA power cable. If the power cable has come already connected to the motherboard, then just plug the other end into the HDD’s SATA power port.​

.

.

Step 4:
.

You now just need to screw the HDD into the bottom of the NVR via the screw holes located in the HDD and corresponding holes in the HDD bay (insert the screws from underneath the NVR into the HDD inside – it can be a bit fiddly).​

.

Step 5:
.

Finally, screw the NVR’s casing back onto the base. Your HDD is now installed and ready to be formatted during the initial NVR setup, which is explained in Part 2.​

How do I set up my Hikvision IP CCTV System

Read More : Hikvision How To Tutorials Chapter 1

Part 2: How do I complete the basic setup of my Hikvision NVR?

You now need to configure the NVR so that it’s ready to connect to your network. Don’t worry – this is simpler than it sounds. This initial setup is simplest when done on the local GUI, using a directly connected monitor. The following steps walk you through this initial setup process:

Note – Avoid plugging anything into the back of the NVR until instructed to do so in this tutorial.

Firstly, you’ll need to look at the back of your NVR and make sure you can identify the following parts that are needed for this stage:
.

[1] – PoE (Power over Ethernet) ports (Most Hikvision NVRs have PoE ports which will power any camera via the network cable. Those that do not will require you to connect the camera across remotely, using a separate PoE injector or switch for power.)
​

[2] – VGA display port
​

[3] – HDMI display port
​

[4] – USB port(s) (and mouse – one should come included with the NVR)
​

[5] – LAN port (and ethernet cable – Cat5e or Cat6 is fine)
​

[6] – Kettle power socket (the power lead is included with the NVR)​

Now, follow these steps. It is easier if you leave your cameras disconnected until prompted later in this guide:

Step 1:
.

Plug the kettle plug into the power inlet to connect the NVR to a power supply.​

​

​

.

​

Step 2:
.

Connect your NVR to a display (this can be any monitor or television) by connecting either an HDMI or VGA cable from the monitor to the corresponding port in the back of the NVR.​

​

.

​

Step 3:
.

Plug your USB mouse into one of the NVR’s USB ports.​

​

​

Step 4:
.

Use an ethernet cable to connect your NVR to your local network – Plug one end of the cable into the RJ45 ports into a network access point (such as an ethernet port on your router), and the other into the LAN port in the back of your NVR.​

​

​

.

​

Step 5:
.

Turn the NVR on and let it boot up. Ignore the beeping noise, it’s completely normal and just the NVR telling you that it isn’t properly configured yet.​

​

You may get a prompt to adjust the NVR’s resolution to match the connected display, click “yes” to view everything in the best resolution supported by your display.​

​

​

​

Step 6:

​

Set your language when prompted.​

​

​

​

Step 7:
.

Set a password for the NVR , as well as a “Channel Default Password”, which will be passed onto any inactive device that is directly connected to the NVR’s PoE ports. We recommend keeping these passwords the same for simplicity’s sake. It’s key that you set a password that the NVR defines as strong and that you remember this password, as resetting the passwords on Hikvision devices can be a hassle that you want to avoid, if possible.​

​

Note – If you have lost your password then please see our guide on How to Reset the Password of your Hikvision Camera/NVR in 5 steps using the SADP Tool​

​

​

​

Step 8:
.

Now set a valid “reserved email” address for the NVR, which Hikvision will use for verification if you need to reset your password.​

​

Step 9:
.

Next, set an unlock pattern of your choice by using your mouse to draw any shape you like – you will be asked to do this twice to confirm the pattern. This will be used to quickly login to your NVR in the local GUI.​

​

​

Step 10:
.

Now, set your time zone, your preferred date format, and date/time.​

​

​

Step 11:

​

On the Network Setup page:​

​

Leave the “NIC Type” as it is.​

​

Either leave the “Enable Obtain DNS Server” box ticked, or untick it and use one these recommended public DNS servers.​

​

It is best to leave the “Enable DHCP” box unticked here. Instead, set the “IPv4 Address” of the NVR to an unused IP address on your network, which is within your gateway’s range. Your Gateway will typically be the IP address of your router. E.g. if your router’s IP address is “192.168.1.1”, you’ll want to give the NVR an IP address within the range of “192.168.1.x”, where “x” is any unused address between “2” and “254”.​

​

Note – DHCP can be left on during this stage of the setup to automatically assign your NVR an open IP address if you like, just be sure to turn it off again once your system up and running. To disable it again once set up, just go to: ​

System/Configuration→ Network → TCP/IP → DHCP Off → Apply​

​

Input the Subnet Mask of your network (typically it’s “255.255.255.0”) and “IPv4 Default Gateway”. If you’re unsure of these, see the below articles which explain how to check what they are and if a particular IP address is available:​

​

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

The “Internal NIC IPv4 Address” can be left as it is, this just refers to the NVR’s own LAN address (so Plug and Play cameras will use IP addresses on this range).​

​

​

​

Step 12:
.

You can now stop the annoying bleeping! Select your hard drive(s) from the list and click “Init” to format it, and then “Next” when the formatting has completed.​

​

Note – This will completely wipe the drive, so please make sure that any that are being reused to not have data that you might need on them. ​

​

Step 13:

​

The next page is for the Camera Setup. As mentioned earlier, we recommend connecting any cameras after the NVR setup process has completed, so you can skip this page.​

​

Note – Please see part 4 for the instructions for adding cameras to your NVR after the initial setup. ​

​

Step 14:
.

You will now be taken to the platform access page. Again, skip through and leave this for now.​

.

Note – Please see part 12 for adding the NVR to the Hik-Connect app, which revisits this page. ​

​

​

Step 15:
.

Finally, you’ll be taken to the Change Password page and given the option to set a new admin password. Ignore this, unless you actually want to change your password. Remember, your admin password is different from your activation password, which you’ll need to use when activating individual cameras on your network.​

​

Click “Exit” and “Yes” on the “Exit Wizard” popup.​

​

​

.

That’s the initial setup of your NVR complete. You should now be taken to the NVR’s live view page (you won’t see your cameras until these are connected in Part 4), with your main navigation menu at the top of the screen.​

​

Check out the other pages for more!

.

<p>The post How do I set up my Hikvision IP CCTV System first appeared on NVR IPCAMERA SECURITY.</p>

with a wealth of intelligent products, we strive to identify and satisfy diverse demands by delivering intelligence at your fingertips; through innovative AIoT applications, we are dedicated to empowering every individual to enjoy a better future by building an intelligent world that is more convenient, efficient and secure.

Hikvision ‘How To’ Tutorials

Here you can find all of the Hikvision-related ‘How-To’ Tutorials that the team at use-IP have created

How Do I Configure the Camera’s Onscreen Display Text?

All Hikvision users will have seen that when you first log in to a camera the live view will have overlayed text stating the date & time and the default name of the camera “IPcamera 01”, depending on your requirements you may want to change some or all of this overlay text and below is the instruction for how to do that.

Method 1 – In a Web Browser

Log in to the camera and go to Configuration > Image > OSD Settings
.

Below we will take you through each of the above settings and what they do:

Character Set – This lets you select the characters/language the OSD settings use, by default all UK stock will come with this set as GBK for English characters but if you are a European customer and you want to enter special characters from your particular language (e.g. é, ü, ç, etc…) you can switch it to EUC-KR to access those characters (do this will require the camera to reboot).

Display Name / Date / Week – These tick boxes let you show/hide the camera name (Display Name), the current date (Display Date), and the day of the week (Display Week)

Camera Name – This box lets you set the displayed name of the camera, it will also change the name of the camera shown in the System menu and if added to an NVR it will change the name shown in the live view camera list and the Camera Management list.

Time Format – This dropdown lets you select how the time appears in your live view, either 24-hour format (00:00 – 23:00) or 12-hour format (00:00 – 12:00)

Date Format – This dropdown lets you select how the day, month, and year are displayed. Your options are DD/MM/YYYY (UK format), MM/DD/YYYY (US format), and YYYY/MM/DD (Chinese/International Standard format). You also have the option of separating the day, month, and year with either a “–” or a “/“.

Text OverLay – On most cameras, you should have the option to add up to 4 additional text overlays to the live view. You can use all of them or none of them depending on your requirements.

Display Mode – This dropdown lets you choose how the text behaves on screen, by default it will usually be set to Not Transparent & Not Flashing which means the text will obscure objects/people behind it and it will be onscreen all the time. You have the option to change it to one of the following – Transparent & Flashing / Transparent & Not Flashing / Not Transparent & Flashing – When set to transparent the text will become semi-transparent so that you can see objects/people behind the text and if set to flashing the text will flash on & off screen every few seconds (there are no controls for the flashing duration).

OSD Size – Technically this setting should adjust the size of the OSD text but we’ve found that when changing it there was little change to the text and so we would just stick to the default Auto option because this will allow the text size to adapt based on where you are viewing the live image (e.g. whether a small phone screen or a large TV).

Font Color – This dropdown lets you select the colour used by the OSD text, by default the camera will use Black&White Self-adaptive which means the text colour will automatically switch between black & white based on what is behind the text (e.g. if a person walks through the text) and for high-security sites, this can be an important feature for using the footage in court because the adaptive text shows that the image/text has not been manipulated in post. If the scenario requires it you can select Custom which will allow you to pick the text colour from a standard colour table.

Alignment – Again like OSD size this setting doesn’t appear to have a huge impact so we would just leave it as the default Custom and you can adjust the positioning/alignment of the OSD text by dragging the red boxes around the live view window above (these red boxes are only for adjusting the text position and will not appear on the actual live view image).

Hikvision How To Tutorials Chapter 1

Read More : Hikvision Devices password reset all methods guide

.

Method 2 – Via the NVRs GUI

.

You can access similar OSD settings from the NVR by going to Camera > Display and selecting the camera you want to configure.

.

Although, as you can see from the above screenshot you won’t get all the settings that can be found by logging into the cameras directly.

How do I set up ‘Rotate Mode’ on my Hikvision IP camera for the best picture in narrow scenes?

Corridor mode is a really useful feature available on many different CCTV cameras that can be utilised to effectively monitor a space that is more vertical, rather than horizontal, in shape. These types or areas include hallways, pathways, staircases, shopping aisles, tunnels and roads. When installing and viewing a CCTV camera, you want the image frame to include as much of the area of interest, while cutting out as much of the redundant areas, like the walls and ceiling, as possible.

Corridor mode allows you to rotate the camera’s lens and the video image 90 degrees so that it’s in a portrait, rather than a landscape format. As a result, you can use the camera to really focus on those areas of interest of within in your frame changing the image’s aspect ratio from 16:9 to 9:16 to suit narrow monitoring settings. The image below is taken from a camera making use of this function and illustrates the differences between the corridor and standard settings:
.

This guide will show you how to utilise corridor mode on Hikvision’s three most popular camera types: domes, turrets, and bullets. I will cover how to activate this useful setting in iVMS-4200, a browser, and locally through your NVR’s GUI so that, irrespective of your setup, this guide should be of help.

Part 1: How do I activate the corridor mode function in my camera’s settings?

We suggest getting your camera set up on your network and activating corridor mode in its settings before you try to rotate and position the lens. This way, you can use the live video stream, in the correct aspect ratio, to point the lens in your optimum direction. Positioning the lens often involved a bit of trial and error to get the best result specific to your space.

.

Note – For the G2 AcuSense models, you will need to connect to the camera directly in a web browser and change the “VCA Resource” to Monitoring Mode by navigating to:​

​

Configuration → System→ System Settings → VCA Resource​

​

​

.

​

Please note that this will disable most of the smart event options, leaving only Scene Change Detection available to use. ​

Locally (via a monitor connected to an NVR):

If your camera is connected to an NVR, then you can easily configure corridor mode in the setting through the NVR’s GUI menu. Just Navigate to:

Menu > Camera > Image

Pick your camera from the top drop-down box beside Camera and then select “Clockwise 270 degrees” in the Enable Image Rotation box

Then, just click Apply

Through iVMS-4200:

If you’re not using an NVR, or don’t have easy access to your NVR’s GUI, then an option is to use iVMS-4200 to set up corridor mode by accessing the camera directly.

To do this, first, you’ll need to navigate to:

Menu > Device Management

.

Find your camera in the device list. If accessing a camera connected to an NVR, you’ll need to open your NVR within the Group section of the Device Management screen and then the particular camera within the NVR’s device list.

Click Configure (the small cog) on your camera.

If your camera isn’t connected to an NVR, then open Basic Settings, if it is then open Advanced Function.

.

In the popup window, open the Image tab in the sidebar. You should then see either a tick-box or drop-down that allows you to turn on Rotate, tick or select ON in the applicable box or drop-down and then Save. The camera view should now have been rotated.
.

.

In a web browser:

The other method commonly used to access cameras and NVRs is through a web browser. You will only be able to configure the image rotation settings for a remote camera. The image for cameras connected directly to an NVR cannot be rotated in this menu due to the restricted access to the camera’s settings.

To access your camera in a browser, simply input its IP address into the browser’s address bar and hit enter. You’ll be taken to a login screen, here you’ll need to fill out the username and password combination you created for the camera when you first set it up. If correct, you should be taken to a page displaying the camera’s live video stream.

The process of rotating the camera’s image is relatively similar to that in iVMS-4200, just go to:

Configuration > Image > Video Adjustment > Rotate > On

The setting should be automatically saved, you’ll see a popup in the bottom-right corner of your window confirming this. That’s it!

.

.

.

Part 2: How do I position and rotate my camera’s lens correctly?

Rotating the camera’s image through its settings will rotate the image 270 degrees. To rotate the final video stream to the desired 180 degrees, you will manually need to turn the camera’s lens 90 degrees in the opposite direction as compensation. The entire process allows the rotated image to properly fit a 9:16 portrait aspect ratio. You’ll need to follow the below steps in order to rotate the camera’s lens.

For Domes / Mini Domes:

Domes and mini domes are the fiddliest type of camera to move and rotate the lens on. You can do this with the camera either installed or taken down. You’ll need to take the outer casing off the dome first to allow you to move the lens inside.

Then, loosen the locking screw located to the right of the lens rotate to allow you to move the lens and bracket. Now twist the lens bracket (the bit that can turn surrounding the lens, see the picture below) 90 degrees anti-clockwise, so that the gap in it is in the 3 o’clock position. You should see the “90” marker in the middle of the gap once in this position.

Now twist the lens (see the picture below) 90 degrees anti-clockwise, holding the lens bracket in place while doing this helps, so the “90” marker is at 12 o’clock and the “0” marker is in the 3 o’clock position. It may take a bit of wiggling and feel unnatural but the lens will move to this position, you won’t break anything!

.

Finally, rotate the lens bracket 90 degrees clockwise so that the gap is at 6 o’clock, and then move the lens so that is fits into this gap, so it looks like the picture below. This next stage takes a bit of trial and error on your part to get your desired camera view.

You’ll need to fiddle around with the lens while looking at the camera’s live stream to ensure it is straight and something you’re happy with. Viewing your stream through iVMS-4200 or Hik-Connect is best as you can look at the image and remotely while fiddling with the lens position at the same time.

.

For Turrets:

Rotating the lens on a turret camera is a slightly more straightforward process. First, you’ll need to remove the trim ring (shown in the picture below) by twisting it anti-clockwise and lifting it off the base of the camera.

.

This should expose the locking screw, you’ll need to loosen this using a Phillips-head screwdriver enough for Turret’s ball to be rotated. You shouldn’t need to take the screw out entirely. All these parts are labeled in the picture below. The “UP” marker on the ball indicates the top of the camera.

You’ll now need to rotate the ball 90 degrees anti-clockwise so that this marker moved from the 12 o’clock to 9 o’clock position. Now, tighten the locking screw back up and replace the trim ring to its original position. The lens should now be appropriately rotated.

.

For Bullets and Mini Bullets:

The camera models that allow for the easiest rotation of their lenses are bullets and mini bullets.

It is important to note that the sun shield on these cameras cannot be moved to be above the lens when rotated, which presents a drawback so using them for corridor mode.

The sun shield will sit to the side of the rotating lens in this case so you’ll need to make sure that you shelter the camera somewhat (such as under the eaves of a roof) if setting a bullet or mini bullet for corridor mode.

Mini bullets have a locking nut (shown below) at the end of their base which will allow you to rotate the camera when loosened. Larger bullets will require you to loosen the locking screw, which is the screw furthest to the right of the base if looking at them (shown below).

Once you’ve loosened the locking screw/nut as appropriate, rotate the main body of the camera 90 degrees anti-clockwise, so that the sun shield is in the 9 o’clock position. This will rotate the lens. Once you’ve done this, tighten the screw or nut again to secure the camera in its newly rotated position.

.

.

Part 3: How do I change the layout of my camera streams to accommodate for corridor mode?

Once your camera is all set up in corridor mode, you’ll want to be able to adjust the way that you view the grouped cameras to avoid the camera’s live stream being reduced in size to fit the standardised landscape 16:9 frame. This is easily done by simply merging two of the landscape frames to make a portrait, 9:16 frame to which you can dedicate your camera.

This custom view layout can be set up in an NVRs local GUI and in iVMS-4200. Please see the guides below for an explanation on how to customise your stream layout to accommodate corridor mode.

In iVMS-4200:

Click on the small icon made up of several small boxes at the bottom of your Main View screen in the program, this should bring up the window division page. Click Add to create a Custom Window Division.

.

In the Add Custom Window Division popup, set the name and dimensions of your new stream layout as desired.

Now, click and drag your mouse over the two frames you want to merge to select them both. Once they’ve both been highlighted by a surrounding red box, click Joint to merge them. Now click Save.

.

Once back in the Main View, click on the Window Division icon in the bottom right-hand corner again and select your new custom layout from the list. Your new stream layout should load ready for you to assign the individual cameras to.
.

Locally through your NVR’s GUI:

Please Note – This option is only available on NVRs that are running Version 4 firmware. There is not currently an option to customise your stream layout on K-Series recorders. If you’re running Version 3 firmware then your only option is to configure your layout as per above in iVMS-4200.

It’s also useful to be able to customise the stream layout as viewed directly from your NVR’s GUI as this is many people’s preferred method for observing and configuring their camera feeds.

To do this, firstly, you’ll need to navigate to:

Configuration > Live View > View > Set Custom Layout (small cog in bottom-left hand corner)
.

In the Custom Layout Configuration popup, set the name and dimensions of your new stream layout as desired. Now, click and drag your mouse over the two frames you’re going to merge and click the Joint button in the top toolbar, followed by Save.
.

Once back in the Live View, click on the Split button in the bottom-right hand corner of your screen. Then, select your new custom layout from the Custom Layout list that appears to load your new stream layout. You can then add the camera streams to each frame as appropriate.
.

You should now be up and running with corridor mode set up properly on your camera! Feel free to start a new thread or comment below with any other questions or suggestions. Thanks for reading!

How Do You Setup Event Pre & Post Recording for a Hikvision Camera?

To Adjust the smart event pre-record and post-record you need to follow these steps:

1) Log in to the NVR/Camera

2) Go to Configuration > Storage > Schedule Setting > Record Schedule

3) Click the ‘Advanced’ button at the top right of the record schedule
.

4) Select the duration you want from the pre/post record dropdowns and click OK
.

​

One thing to be aware of with event pre/post-recording is what Hikvision call a Buffer Zone. The buffer zone is simply a bracket of footage around the current moment in time that is continually recording/erasing, this buffer zone allows you to record only by event but still have access to footage before and after the trigger event without having continuous recording enabled.

The issue is that the buffer zone is limited to around 2-4MB of storage and so the higher your resolution and stream settings the larger the files sizes are and thus the maximum duration of the buffer you can use is limited.

So basically an 8MP camera will not be able to have as long pre/post recording durations as a lower-spec 4MP or 2MP model. (unless you reduce the resolution/stream settings of the 8MP camera)

We recommend that to get the longest duration possible from your pre/post recording you should set them to the not limited option to use the full 2-4MB buffer capacity.

(One other thing to be aware of, there is no advantage or disadvantage for pre/post recording when using an NVR. Although the NVR is managing the event recording, each channel on the NVR is still set to the same 2-4MB buffer, the same as the individual cameras. So you would not get more pre/post recording capacity with 1x 8MP than you would with 8 x 8MP cameras on an NVR.)

How do I stop my Hikvision NVR from beeping?

If a Hikvision NVR notices what it deems to be a critical error, or “exception”, it will make a constant beeping sound to draw your attention to this.

These exceptions can occur when:
.

• A hard drive has not been installed or properly formatted

• There is an error with the hard drive, it has been damaged, or the cameras are just not recording properly

• A hard drive has been filled and not set to overwrite

• There is an IP conflict, preventing the NVR from operating properly

• The NVR detects an illegal login

• The NVR loses its network connection

Of course, ignoring these exceptions are not recommended. However, you can disable the beeping while you address whatever the issue is by following the steps below.
.

.

​

Step 1:​

Connect to your NVR in a web browser by using its IP address and logging in.​

​

Step 2:​

Check what the exception that is causing the beeping is in the NVR’s logs. To find these, go to:​

​

Configuration → System → Maintenance → Log​

​

Set the log search so that the “Major Type” is “Exception”, with the start and end time covering a period when the beeping has occurred.​

​

For example, you can see that it is an IP address conflict causing it in this case.​

​

Note – Camera disconnections will not cause the NVR to beep. ​

​

​

.

Step 3:​

Go to:​

​

Configuration → Event → Basic Event → Exception​

​

Find the “exception type” identified in step 2 in the dropdown on this page.​

​

.

Step 4:​

Select the exception shown in your logs from the dropdown.​

​

You will see that “Buzzer” is ticked as a “Normal Linkage” action, which is what is causing the NVR to beep.​

​

.

Step 5:​

Untick this, click “Save”, and the beeping should stop.​

​

My Hikvision NVR has both HDMI & VGA connections, can I connect two monitors to my NVR?

This question gets asked a lot and we have always assumed that as the larger Pro NVRs (9600 Series) have 2 x VGA & 2 x HDMI that they were the only models that would support any kind of multi-screen setup.

Today we did some tests with a selection of demo NVRs we have in our office to see if it was possible to connect two monitors to an NVR that only had 1 x VGA & 1 x HDMI, below are our findings from testing K-series & I-series NVRs

K-series (DS-7604NI-K1-4P(B) / DS-7608NI-K2-8P / DS-7616NI-K2-16P / DS-7716NI-K4-16P / DS-7732NI-K4-16P)

When we connected a monitor to both the VGA & HDMI of a 7604 4-channel NVR we were able to see the usual K-series GUI on both screens at the same time, but with the older K-series GUI when viewing on two monitors your actions will be synchronised (e.g. when you move the mouse on one screen the mouse will do the same movement on the 2nd screen, and this is the same for any action whether it’s opening menus and selecting individual live streams).

So the main disadvantage of this is that you can’t have different live views streaming on each monitor, both monitors will show exactly the same thing and the only difference will be that one will be a VGA quality. The advantage of these synchronised displays is if you have a setup with say a large wall-mounted monitor and a smaller desktop monitor,

you can have the HDMI output to the big screen while you operate from a smaller VGA screen, this kind of setup would be useful for any situation where you need to demonstrate a feature of the NVR or play back footage in real-time to a large group of people.

I-series (DS-7608NI-I2-8P / DS-7616NI-I2-16P / DS-7716NI-I4-16P /DS-7632NI-I4-16P / DS-7732NI-I4-16P)

We have a 7716-I NVR as part of our demo system in the office and when we connected two monitors to the VGA & HDMI connections on the back we got the live streams displayed on both monitors just like we did with the K-series NVR. The difference with the I-series NVRs is that they use the latest 4.0 GUI, and on the live view page of this new interface you will find an icon in the bottom right

of the screen labelled ‘AUX Monitor’ (see image below), clicking this icon allows for you to switch control between the HDMI & VGA screens and allows you to move through the NVR menus on one screen whilst keeping the cameras streaming on the 2nd screen.
.

​

Now that you have the ability to switch between and control multiple screens you would obviously want to be able to set each screen up with their own camera stream layouts, to do this simply go to the System page (cog icon at the top of the 4.0 GUI) and then click the Live View tab and select the view page from the dropdown options. On this page you can switch between the HDMI & VGA screen and set the camera stream layout for each monitor (see image below).

There are limitations to how you can set the layouts, you can set the same camera to appear on both screens in the same place or in different positions and you can also spread all 16/32 cameras out across

the 2 screens, the main thing you can’t do is have a camera appear in different positions when using different live view layouts on the same screen (e.g. if you put camera 1 in the top left position for the 2*2 layout it will also appear in this top left position when you switch to the 3*3 layout).
.

9600 Series, Deep in mind, and Other NVR models

We don’t tend to get hands-on with these larger, top of the range NVRs but as you will see from the product pages and datasheets for these models a lot of them have 2 x VGA & 2 x HDMI connections. We assume that the 2 x connections on these models takes the multi-screen setup one step further by allowing you to seamlessly

move your mouse between screens (like you can with a 2 screen setup on a PC), thus allowing you to adjust each screens layout with ease and see all your camera streams in full quality via HDMI connection on both screens. (be aware that you will only see the full resolution stream of each camera when you select to view main-stream)

If anyone out there on the forum has had experience using two monitors with a 9600 Series NVR (or any other top of the range NVR with dual VGA/HDMI ports) then please share any information you have in this thread.

How do I set my Hikvision ColorVu camera’s built-in light to turn on during event periods?

We’re often asked if a ColorVu camera’s built-in supplementary white light can be programmed to turn on during VCA event trigger periods, such as during instances of motion detection, intrusion detection, or line crossing detection.

After testing, we can confirm that this is now possible on all 2nd Generation ColorVu cameras (any with a ‘G2’ in the part number) and works reliably.

In effect, it means the light on the camera can be used like a PIR floodlight, but with more control over a number of variables. Notably, trigger object type (human, vehicle, or both), the motion detection area, and direction of trigger object movement.

Please see the below steps for instructions on doing this.
.

.

.

Step 1:​

Connect to your camera directly in a web browser, even if it is recording to an NVR.​

​

If your camera is connected to your local network, just use its local IP address to do this.​

​

If it is directly connected to your NVR’s PoE ports, then you will need to use the virtual host feature to connect to the camera via your NVR’s Camera Management page.​

.

Step 2:​

If you have a ColorVu camera from the G3 platform, then make sure you have installed the firmware, version 5.5.800 (build 210628), or later.​

​

If you have one of the G5 models (indicated by a ‘C’ at the end of the part number), install version 5.7.2 (build 211228).​

​

You can also check your camera’s platform when connected to it in a web browser by going to:​

​

Configuration → System→ System Settings → Basic Information​

​

The platform will then be indicated by either a “G3” or “G5” in the “Firmware Version Property” box:​

​

​

Note – Please see this guide for instructions on how to check and update the firmware on your camera.​

.

Step 3:​

Once you’ve logged in, navigate to:​

​

Configuration → Event → Basic Event (for motion detection) / Smart Event (all smart event options support this) → Select your preferred event type​

.

Step 4:​

Enable and set your event up in the Area Settings and Arming Schedule pages, this guide explains how to set up motion detection, line crossing, and intrusion detection.​

.

Step 5:​

Navigate to the “Linkage Method” page, tick the “White Light” box, and set how long that you want it to remain on for on event triggers (in seconds) in the “Duration” box.​

​

Click “Save” once this is done so the settings are kept.​

​

How do I use a Hikvision NVR’s “Virtual Host” feature?

One of the most successful selling points of a Hikvision NVR to many small-setup customers is the “Plug and Play” functionality that simplifies the setup process of their surveillance system.

However, plugging a camera directly into a port on the NVR, unfortunately, does not allow you to access the camera via its own internal LAN IP using a browser due to it being on the NVRs internal network, and this can significantly reduce the number of configuration options you have access to.

The NVR does allow you to configure many options for each connected camera, but some essential features are only accessible via connecting to the camera itself (such as audio codec options). This was of course a big problem previously.

With the advent of newer firmware and models of NVR, Hikvision has introduced a feature called Virtual Host. Activating this feature turns your NVR into a “host” for the cameras allowing you to connect to them via a browser. Essentially, the NVR forwards all traffic received from your browser to the appropriate camera you’re trying to connect to, eliminating the biggest problem of plug and play functionality.
.

.

Step 1:​

First of all, access your NVR via a web browser. If you do not know the LAN IP of your NVR, download Hikvision’s tool SADP tool, which scans your network for any Hikvision devices that are connected and allow you to see and change their network settings, including the IP address.​

​

Download SADP for Windows ​

Download SADP for MacOS​

.

Step 2:​

Once you’ve logged in, navigate to: ​

​

Configuration → System → Camera Management​

.

​

.

This screen displays all the connected cameras on your NVR. Notice that the final column labelled “Connect” is currently empty. We’ll be coming back here in a moment.​

.

Step 3: ​

Now, navigate to:​

​

Network → Advanced Settings → Other ​

​

Turn on the Enable Virtual Host option.​

​

Note – Your NVR will reboot when you click “Save”.​

.

.

​

Step 4:​

Now, navigate back to the Camera Management window from earlier. You’ll notice that the previously empty connect tab now features links for each camera currently connected to your NVR.​

.

​

Step 5:​

Click on any of these links to access the respective camera via your web browser:​

That’s it, you’re done!

This should be useful when you want to access options on your camera that your NVR doesn’t feature. If you have any further questions feel free to ask, we’re happy to help.

Why am I not able to tilt my Hikvision PTZ camera upwards?

Hikvision PTZ cameras are not usually set by default to have their full range of movement enabled. This often means that cameras that are advertised as being able to tilt upwards are not able to do so straight out of the box, as this needs to be enabled in the camera’s settings.

You can check the movement range available on your camera in the PTZ section of its datasheet. Below is an example of this range shown for the DS-2DE5425IW-AE (S5):
.

​

0˚ tilt refers to the camera being in its home position, where it running parallel to the ground beneath and looking straight out at the scene.​

Any negative figure (e.g. -15˚) here refers to the angle that it can tilt to upwards of the 0˚ position.​

Any positive figure (e.g. 90˚) refers to how the angle of tilt available below this 0˚ position.​

​

Cameras with “auto flip” will rotate 180˚ and then flip their image when it reaches its full 90˚ downwards tilt, which will give the illusion of you having a full 180˚ (or more) range when you try to continue to tilt beyond this 90˚ position.​

To change the movement range currently set on the PTZ, you will need to connect to the camera directly in a web browser.
.

NB – If your camera is directly connected to an NVR’s network ports, then you will need to use the Virtual Host feature to access the camera’s backend. If it is connected to your local network, then you can just browse for its IP address to do this. ​

Then, go to:
.

Configuration > PTZ > Basic Settings > Max. Tilt Angle​

​

​

You should have some different options in this dropdown, depending on the maximum tilt range of your camera. If you want to enable the complete range of movement, then select the option with the largest range between the two figures (in this case, “-15 – 90˚”).​

Once you have chosen an option that you’re happy with, make sure to click “save” at the bottom of the page so that these changes are updated on the camera.

How do you Shutdown a Hikvision NVR?

This is a common question by Hikvision users so we thought we would create a short forum post to give a clear answer on the possible ways to shutdown an NVR.

Direct Monitor Access
If you are accessing your NVR from an HDMI/VGA monitor then it is possible to shutdown the NVR from within the menus, depending on the NVR model the menus and shutdown process is slightly different as you will see from the below explanations:

I-series (76xxNI-I2 / 77xxNI-I4 / 96xxNI-I8 / 96xxNI-I16) & K-series (7604NI-K1/4P(B) / 76xxNI-K2 / 77xxNI-K4) NVRs – In the top right corner of the live view you will see a power icon which if you hover over will bring up text that says either ‘Power’ or ‘Power Off’, click the icon and a pop-up menu will appear with 3 options, one of which will be shutdown.

Click shutdown and a box will appear saying ‘shutting down…’ and then after 20-30 seconds, new text will appear asking you to switch the NVR off at the back to complete the shutdown.

(Above is for I-series and K-series NVRs that are running 4.0 GUI and EUI GUI respectively, if your NVRs are running older firmware and not using the latest user interface you will need to follow the below instructions)

7604NI-K1, E-series (76xxNI-E1 / 76xxNI-E2 / 77xxNI-E4), SE-series, and other older generation NVRs – Right-click the live view page and select the main menu from the dropdown, one of the menu options should be clearly labelled ‘Shutdown’ which when clicked should bring up the same 3 options as mentioned above.

Click ‘Shutdown’ and a window should appear with the text ‘shutting down…’ and roughly 20-30 seconds later new text will appear asking you to switch the NVR off at the back to complete the shutdown.

Browser Access
if you are accessing the NVR primarily from a browser then your only option for shutting the NVR down is to simply flick the switch on the back of the NVR because the browser menus do not include a button to shut the NVR down like you can with the direct monitor.

How do I know if the lens on my Hikvison mini dome is orientated correctly?

It’s easy to install your Hikvision mini dome only to turn it on and find that the image is upside down. If you’re not familiar with Hikvision cameras, adjusting the lens and settings can be confusing. This post will explain the two different ways that you can rotate your camera’s image by:
.

1.Manually rotating the lens itself.

2.Rotating the cameras image 180° in the image settings.

Part 1: How do I orientate my camera’s lens manually?
.

1.Remove the mini dome’s cover by loosening the screws surrounding the glass dome, shown in the image below:

.

2.You should now be seeing something like the image below. Loosen the locking screw to the right of the lens, and then the lens bracket which locks the orientation of the lens in place. The lens is effectively attached to the camera body via a ball and socket joint, so this can be orientated however you like.

Part 2 of this guide explains rotating the lens in more detail, as well as how to rotate the lens on the turret and bullet styles of camera – How-to: How do I set up Corridor Mode on my Hikvision Turret, Bullet or Mini Dome IP CCTV camera?

NB – This image shows a camera with the lens rotated 180°, you’ll actually need this 90° marker to be in the 3 o’clock position, and the 180° marker pointing towards the bottom of the unit.

.

3.The lens should be positioned like the one shown in the below image. The small line marker located directly parallel to the 180° marker signifies the top of the lens. So, this needs to be pointing up, towards the top of your scene. This will orientate the camera’s view correctly. You should also make sure that the lens bracket is repositioned correctly so that the thicker part surrounds the top half of the lens.

.

4.Now, tighten the locking screws and fasten the dome cover back in place, making sure the cover screws are tight to prevent water ingress into the camera. It’s always worth checking your camera stream before doing this to make sure that the camera view is orientated as you like.

For a guide on installing you Hikvision IP camera correctly to ensure it is properly waterproofed, please see this guide – Please Read: IMPORTANT – Installing Hikvision IP Cameras Correctly

Part 2: How do I orientate my Hikvision camera’s view through its settings?
.

1.Log into your camera’s web browser interface (not your NVR’s), by entering its IP address into the browser’s address bar. This will only work for cameras that are on the same LAN as your PC. If the camera is directly connected your NVR’s PoE ports, then you will need to use the NVR’s ‘VIrtual Host’ feature to access the camera’s own browser view, which gives you access to a wider range of settings.

NB – It is recommended that you use Internet Explorer if possible. If you are a macOS user, the best web browsers for this seem to be Google Chrome or Apple’s Safari. You might need to install Hikvison’s macOS Web Plugin as well.

2.When you have access to the cameras in a web browser, go to:

Configuration > Image > DIsplay Settings > Video Adjustment

The different options are will adjust your image as described below:

Left/Right: The image will be flipped horizontally, so it appears as a typical mirrored image.
Up/Down: The image will be flipped vertically, which will still show a mirrored image of the default view as you are not actually ‘rotating’ the image 180°
Center: This will be the option that you need to select to rotate the image 180°, which will show the same view as physically rotating the lens would.

If you only need to rotate the image 90°, then setting the Rotate option to ON will do this, as shown below.

To rotate your view 270°, set the Mirror dropdown to Center, and then set Rotate to ON.
.

Thanks for reading – hopefully, this will prove helpful to some of you in the future! As always, please feel free to post any questions or feedback that you have below or by creating a new thread.

Hikvision Password Reset Options – 4 Ways the User can reset their Passwords

The new video from Hikvision (linked below) takes you through the 4 password reset options that the user can do themselves, these are:

1. Reset Password by reserved email
2. Reset Password via Hik-Connect App
3. Reset Password via Security Questions
4. Reset Password via GUID File

IMPORTANT: Not all of the above options will be available on all Hikvision products, also be aware that all the above options do require some level of pre-configuration to use them so if you have done none of the setups explained in the video you will have to follow the traditional reset file method as described here (remember though that we at use-IP will only reset passwords of our own customers)

How to Set up the Hikvision 2nd Generation Modular Intercom

We get asked a lot of questions by people looking to buy or who have already bought Hikvision’s 2nd Gen modular Intercom solution and for a long time, we have had to take the majority of those questions to Hikvision Support as we just don’t have enough hands-on experience with the intercom solution to answer them confidently.

Now we have finally found time to get a demo intercom system set up, test some of the features, and give you a guide of how to get a basic intercom solution up and running.

The below guide will initially** be split into 3 key sections with multiple sub-sections:

Single Module Setup (Video Intercom Module)
.

• Setting up the Video Intercom Module

• Setting up the Indoor Station

Three Module Setup (Video, Indicator, Keypad)
.

• Sub Modules & Dip Switches

• Setting Room Numbers & Unlock Codes

Six Module Setup (above + Display, RFID, nametag)
.

• Nametag & Display Modules

• Card Reader Module

The reason we have decided to cover it this way is that the modular nature of the solution means there are too many variations to cover specifically, so instead we will cover the details of the 3 most common setups and once you know the basics of all 3 any combination of modules should be achievable.

(**IMPORTANT – This will be a continual work-in-progress thread and we will add new posts with explanations of new features & settings as we test the intercom further and learn things from customers & Hikvision Support, this initial post will basically be a contents page for the entire thread)

Will the smart tracking feature on a Hikvision PTZ camera allow it to zoom in to its maximum zoom ratio automatically?

We’re frequently asked if Hikvision PTZ cameras will automatically zoom in to their maximum ratio when they are automatically tracking a target. After talking to Hikvision, we found out that you’ll need to do the following to enable the camera to do this:

On the camera’s menu (via a web browser) navigate to:

Configuration > PTZ > Smart Tracking

Here, set the Zoom Ratio to its maximum value, which will then allow the camera to automatically zoom to this maximum ratio.

Do It Youself – How To Silence a HikVision DS-7608NXI-I2/4S AcuSense NVR

Hi Guys,

I’m new to business here, but have made a video tutorial to decrease fan noise on my AcuSense 7608-NXI-i2-4S device. Maybe this helps others as internal construction of many NVRs from HikVision seems to be almost the same.

I also have some questions towards the community.
1. What is my latest firmware available for my NVR?
It is an AcuSense 7608NXI-i2-4s, but as I see it is not a full i-series device.
i-series are up to 4.22, but mine seems to be different. Can I use firmware here or not: Firmware – Latest HikVision Firmware for I-Series NVRs – V4.22.005

2. Scene change detection+alarm seems to be problematic. My cameras are AcuSense 2086G2 Bullet, but they do only detect scene change when going completely dark scene to normal recording scene. If I let them record a normal scene situation and then simulate a camera removal from wall situation – camera does not trigger a scene change event.

How to update the Hik-Connect App on your Android phone using Hikvision’s App Store

The method for updating the Hik-Connect App on Android devices has recently changed to mean that users can no longer update via Google’s Play Store. To use Version 4.1.0 of the app Android users now need to access Hikvision’s own App Store and update via the .apk file which is downloadable from there. The reasons for this change have been discussed in this post, as well as our thoughts on the situation.

This simple tutorial has been put together to walk you through this new method for updating in 5 easy steps, so that you can ensure you install the latest version of the Hik-Connect app is installed properly on your Android device.

Step 1:
Open Hik-Connect if you have it already installed, and press the Upgrade Now button in the popup. If you don’t have the app installed or do not get this popup upon opening the act, this link to the Hikvision App Store will take you to the update file.

You need to make sure you open this page on the Android device that you wish to install the updated software on, as this will be the device that the update file is saved to! In the App store, make sure Android is selected in the top-left hand corner and then select Download beneath Hik-Connect to get the .apk update file.
.

Step 2:
Press Download when the prompt to do so appears at the bottom of your screen. Don’t worry, this is a safe and secure link!
.

Step 3
Select Install when the prompt to do so appears at the bottom of the screen.
.

Step 4
The installation will begin, wait for the progress bar to complete… Go and put the kettle on!
.

Step 5
If you get the same screen as the one below, then you’re all done. You should now have the latest version (V4) of Hik-Connect installed on your device. You can either press Open to launch the app, or Done to return back to whatever you were previously doing. If your screen doesn’t say App installed with a tick above, then you’ll need to repeat steps 1-4 again!
.

How do I set up an alarm to work with an external device on my Hikvision NVR?

We often have customers ask us “how do I get my new NVR to work with an existing alarm system I already have installed” or “how do I connect something to the IN/OUT ports of my NVR?” Indeed, for such an important feature for the NVR’s to have, it is not the most straightforward to get set up with.

We thought it would therefore be useful to put together this guide to walk you through how to configure the alarm function, either through locally through your NVR and monitor, or through Hikvision’s iVMS-4200 software, in 10 easy minutes.

.

Contents:

Part 1: How to wire my alarm system into my NVR’s alarm input and output ports?

Part 2: How do I configure the alarm function settings of my NVR locally via a monitor?

Part 3: How do I configure the alarm function settings of my NVR remotely via iVMS-4200?​

Part 1: How to wire my alarm system into my NVR’s alarm input and output ports?

As daunting as it may seem when you look at the multiple different alarm ports in the back of your NVR, this part is simple enough once you know what you’re doing. If you’re struggling to find you alarm IN/OUT ports, they are the block of green connections which should be labeled as “ALARM IN/OUT” on the device.

The number of connections will vary here depending on the size of your NVR, the picture shown is of a smaller Hikvision DS-7608NI-K2-8P 8 Channel NVR. Larger NVRs will have more of each connection, but nonetheless, the process is the same.

Firstly, make sure you can locate the NVR’s “ALARM IN ” and “ALARM OUT ” ports, with their corresponding “Ground/G” ports. If you’re connecting a device to trigger your NVR cameras with an external event (e.g. a smoke alarm, PIR senor etc) then you’ll need to run the wires from the device into one of the input ports and its corresponding ground port.

If you’re connecting a device to be triggered by a smart event set up on your NVR (e.g. a siren or warning light), then connect the wires to the output port and corresponding ground port. All the ports are marked up in the picture below but should also be clearly labelled on your unit.
.

Part 2: How do I configure the alarm function settings of my NVR locally via a monitor?

Now that all the necessary connections are made, you’ll need to set up your NVR’s alarm function for it to alert the alarm system that you’re connecting to it.

Firstly, I’ll show you how to do this locally. You’ll need to boot up the NVR, once in the menu, navigate to:

Menu > Configuration > Network > General

Here, you’ll need to insert your network’s IPv4 address, IPv4 subnet mask, IPv4 default gateway and your preferred DNS server:

.

• If you’re unsure of your IPv4 address, subnet mask or default gateway, our tutorials on How To find your router and PC’s IP address using a Windows PC or How To find your router and Mac’s IP address using a Mac show you how to do so. Please note, you need to make sure the PC you use to find these is hard wired via a network/Ethernet cable do make sure this turns up the correct addresses for your network/router.

• Unless you know of a preferred DNS server that you’ve set up yourself, Google’s public DNS server address (8.8.8.8) should work fine. It’s worth entering an alternate backup DNS too beside Alternate DNS Server, Cloudflare’s public DNS address is a good option (1.1.1.1). Follow this link for a list of the best publicly available DNS servers.

Now, navigate to:

Network > Email

At this screen, you’ll need to fill in all the fields as appropriate to your Email account. If you’re unsure of these, then complete the fields as below:

Enable Server Authentication: Tick/check this box
User Name: Insert your email address here
Password: Insert the password you use to access this email account
SMTP Server: If you don’t know this, follow this link for “finding your SMTP server address”
SMTP Port: Insert either 25 or 587 here
Enable SSL: Leave this box unticked
Sender: Insert the first part of your email address (everything before @)
Sender’s Address: Insert your email address here
Select Receivers: Insert “Receiver 1/any name” here
Receiver: Insert your email address (same as Sender’s Address)
Enable Attached Picture: Tick/check this this box, it will mean that you’ll receive picture of anything that triggers your cameras’ alarms in an email.
Interval: Insert 5s (5 seconds)
.

When you’ve completed these fields, navigate to:

Menu > Camera

Ensure all your cameras are properly connected to the NVR and are visible on this screen. If you haven’t yet added any cameras to your NVR, this guide on adding Hikvision cameras to an NVR walks you through how to do so.
.

Now, navigate to:

Menu > Configuration > Alarm

This should take you to the Alarm Status menu. This menu lists the status all your alarm IN/OUT ports and any alarms that have been configured/assigned to these ports.

You’ll need to use this screen to check that you’ve set the correct Alarm Type for the alarm/device that you’re connecting. The options you have are N.O (Normally open) and N.C (Normally Closed). In brief, N.O alarm types use switches/sensors that normally remain open with no current flowing through them, so closing the switch allows for the flow of current and activates the alarm.

N.C alarm types, on the other hand, use switches/sensors the normally remain closed with current flowing through them, so opening the switch stops the flow of current and activates the alarm. There’s a lot to be said about N.O and N.C alarms but for now, you only need to know which category the alarm that you’re using falls under. If you want to take a journey down the N.O vs N.C rabbit-hole, I found this article on the differences between N.O vs N.C useful.
.

To assign an alarm to one of these IN/OUT ports, navigate to:

Alarm > Alarm Input > Settings (click on the small cog) > Trigger Channel

Choose the channel that you would like to trigger your alarm. In this case, we’ve selected channel 1.
.

Now, navigate to:

Settings > Arming Schedule

Select the hours that you would like to schedule your alarm to be turned on for. Typically, this would be 24/7, so set the schedule for Monday, Week 1 as 00:00-24:00. Now, copy this schedule to the rest of the week by clicking Copy and then checking the box for All in the popup window. If you only want your alarm scheduled for certain days, then select the specified days in this popup from the list of 1-7 (1 = Monday, 2 = Tuesday etc).Once you’ve done this, click Apply.
.

Finally, navigate to:

Settings > Linkage Action

Tick the boxes for Notify Surveillance Center and Send Email and then click Apply so that you email notifications whenever the alarm is triggered. If you have connected a separate device to be activated by the alarm in the NVR’s Alarm OUT port, then ticking the box for Trigger Alarm Output will activate this device when your alarm is triggered.
.

That’s it for the local setup section of this tutorial! Your NVR’s alarm function should now be set correctly.

Part 3: How do I configure the alarm function settings of my NVR remotely via iVMS-4200?

The first thing you’ll need to do is ensure you have the most up to date version IVMS-4200 installed and that you’re able to view the live feed of your camera(s) through the software.

If you haven’t already added your NVR to the program, navigate to:

Maintenance and Management > Device Management > Add
.

Add your NVR here by filling out the fields in the popup window, ensure the boxes beside Export To Group and Synchronise Time is checked and then click Add.
.

Now find the NVR on your device list and select:

Remote Configuration (the small cog listed beside your NVR) > [Basic Settings] > Event > Alarm
.

NB the configuration menu layout you will see henceforth will vary between two depending on the model of NVR that you have. I have included both variations for each step, so don’t worry if some of the below screenshots look unfamiliar.

Fill out the alarm parameters here, e.g. as follows:

Alarm Input: Select your NVR’s channel that you would like to trigger your alarm (e.g.: A<-1)
IP Address: Local
Alarm Name: Name your alarm as desired
Alarm Status: Normal/Remain Open or Normal/Remain Closed depending on the type of alarm, see the first half of this tutorial to understand the differences
Enable Alarm Input Handling/Enable Alarm Linkage Actions: Check this box
Arming Schedule: All-day Template
.

.

Open Arming Schedule, pick an arming template or a custom schedule of hours that you want your alarm active for.
.

Now, Click Settings beside Linkage Method. Check the boxes for Notify Surveillance Centre, Email linkage and Trigger Alarm Output (if you’re connecting an external alarm device to an output channel), then set the desired Triggered Camera.
.

.

Click Save, and then Save again in the alarm configuration window.

Switch back to Main View and select your NVR from the side panel.

Now, click the small alarm picture and speaker icons at the very bottom toolbar so that they’re both enabled and look like the second image below. This will enable the alarm’s function to send an image of its trigger, as well as the audio.
.

That’s it for the remote setup! It’s always worthwhile testing your alarms to check everything is now working as it should be.

If you have any questions or comments to make, please do so in a separate thread mentioning this tutorial and I’ll get back to you as soon as I can.

How to Unbind a Hikvision Device using SADP on a PC

Unbinding a Hikvision device is not something that is required all that often, in most cases you can do the unbind from within the app. There are though some rare cases when the user does not have access to the Hik-connect account that the device is bound to, for example, if you have purchased a used device that has not been properly disconnected from its previous owners Hik-connect account or if you added the device to an employee’s account and they leave without removing the device from the app correctly.

As long as the Hikvision device has been set up correctly on your local network, then the process of unbinding should be pretty simple:

Step 1 – Open SADP on a PC
Step 2 – Click Refresh and select the device you want to unbind by ticking the box next to the device on the far left of the list
Step 3 – Click Unbind
Step 4 – Enter the current username and password of the device (this is NOT the username & password of the Hik-connect user you are trying to unbind the device from)
Step 5 – Enter the Verification Code and click confirm

You should then see a quick pop-up with a green tick saying Unbind Successful, If the device does NOT unbind and you get an error message like “The device is Offline” or “connecting device failed” then the most likely problem is that your DNS settings for the device are not set correctly.

You can change the DNS settings by logging in to the device using a browser and go to Configuration > Network > Basic Settings > TCP/IP and you will see the 2 DNS boxes at the bottom. We recommend that if you are unsure of what DNS to use that you enter default/most commonly used DNS servers which are shown below:

Prefered DNS – 8.8.8.8
Alternative DNS – 8.8.4.4

Once you have saved these DNS settings the unbind process should work

How do I update HikVision Firmware in just nine simple steps?

Updated 20-2-19 – corrected the link to the portal as Hikvision changed their url (again). Otherwise all is good. We use this method every day. Now viewed over 38,000 times.

Here’s how to upgrade your HikVision camera or NVR to the latest firmware version in just nine simple steps:

Step 1: Download the latest HikVision firmware to your PC.

Step 2: Extract the digicap.dav file (which is the actual firmware file) from the zipped file you downloaded.

Step 3: Copy that digicap.dav file to your PC’s root folder e.g. C://

Step 4: Browse to your NVR, camera, etc – using Internet Explorer:

Step 5: Login and navigate to Config -> Maintenance (screenshot attached below)

Step 6: Scroll to the bottom of the screen you’ll see Upgrade Firmware.

Step 7: Click the Browse button at the right-hand side.

Step 8: Browse to and select the digicap.dav file in your C:// drive

Step 9: Click ‘Upgrade’.
.

I have seen reports that you cannot leap updates, but not encountered the problem myself for some time (applies to old firmware of older models). If you do not succeed in upgrading from your current version to the latest version in a single step, please try interim releases.

Additional helpful tips:
.

1.Use a PC

2.Use a wired connection – PC and camera/NVR wired to your network

3.Use Internet Explorer browser (not Edge)

4.Move the digicap.dav file to your C:// folder (root of your HDD)

5.If you select/download firmware for the wrong camera family or device you will see an error message which states – “The type of upgrade file mismatches”

If you need any help finding the latest Hikvision firmware for your device:

Tutorial videos from HikVision Technical Support:

HikVision Firmware Update using Internet Explorer on your PC

HikVision Firmware Update using a monitor connected to your NVR

NVR Firmware update using a USB memory stick

Upgrade devices using IVMS-4200

NB We cannot guarantee outcomes – if you are one of our customers you will of course have our full support. We have only ever supplied official UK version HikVision cameras & NVRs. If you sourced your HikVision products from another supplier you may want to check their recommendations.

How To Set Up Live View & Playback Audio on Hikvision Cameras

There is a small selection of Hikvision cameras that support some sort of audio – audio I/O, built-in mic, 2-way audio – but on multiple occasions, customers have come back to us saying they are getting no audio on live view or playback. So to avoid this problem in the future we are creating this post to take you through the steps that must be completed to get audio from a Hikvision camera.

Step 1 – Update Firmware

Keeping firmware up to date is always important so it is always where we start with any issue, now most firmware should support the audio but if you’ve had a model for several years and never updated it you are likely on an old firmware and so updating just removes any potential problem that might be caused by out of date firmware.

EU Firmware Portal
UK Firmware Portal

The most common audio cameras will be EasyIP 2.0+ (2xx3G0) and EasyIP 3.0 (2xx5FWD/2xx5G1) which all use the same G1 Firmware.

Step 2 – Video & Audio

Login to the camera, go to the Configuration page and open the Video/Audio menu where you will see all the video settings. The important one for audio is the Video Type which needs to be changed from Video Stream to Video & Audio as shown below:
.

​

Make sure you also switch the Video Type of any other streams you are using, the main one for most cameras will be the sub-stream which is used when viewing the camera from the Hik-connect app. Also, if your camera is connected to a Hikvision NVR make sure to check the camera is set to Video & Audio in the NVRs Video Settings.

Step 3 – Audio

The final Settings to check are the Audio settings which more often than not out of the box is set up correctly and should look like the below screenshot:
.

​

The only setting that might change depending on the model you have is the Audio Input option. If you have a camera with only a built-in mic or 2-way audio then the only option you will have is MicIn, but if the camera only has audio I/O connectors or has both options then you will have both MicIn and LineIn input options. Make sure if your camera has both options that you select the correct input for your setup, LineIn will be used if you have a more powerful audio device connected like an amplifier or a stereo microphone, while MicIn will be for smaller standard Mono microphones.

With all 3 of these steps completed, you should now have live audio from the camera on the browser, app, and direct monitor live view, but there is one final step to have your camera record audio.

Step 4 – Record Audio

Login to your camera/NVR and go to Configuration > Storage > Schedule Settings and select the camera with audio, once you have the schedule for that camera onscreen you will need to click the Advanced button which you will see in the top right of the schedule. A pop up will appear and you will see an option to Record Audio, tick this option and click OK to apply the setting, now all the recorded footage from that camera will have audio.
.

.

.

<p>The post Hikvision How To Tutorials Chapter 1 first appeared on NVR IPCAMERA SECURITY.</p>

Access from smartphone

(1)Download APP

Search and download “Eseecloud” app from App store or Google play on your phone.

.

(2) Register

 If you install and open “Eseecloud” app at the first time, an account need to be registered initially.

ce”.

.

(3) Add device

Method 1: Add the device via QR code.

EseeCloud Devices Advanced User Guide

Read Next : EseeCloud Wireless Security Camera System Installation.

.

Method 2: Add by cloud ID.

     Cloud ID: Enter NVR’s System Setup – Network Setup to input Cloud ID or Scan QR Code)

     Device name: Choose a name for your system of your choice.

     User Name: Enter the NVR’s User Name (default: admin)

     Password: Enter the NVR’s Password (default: NO password)

.

.

Method 3: Add by LAN scan.

Please make sure you are connected to the same wifi.

.

Access from remote PC

1. Access from remote PC (Log in with Cloud ID)

Operation Steps: ( We suggest you to use microsoft IE, otherwise some services will be invalid. )

1. Open your browser

2. Enter http://www.e-seenet.com

.

Cloud ID: (Enter NVR’s System Setup-Network Setup to input ID or Scan QR Code)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

3. Enter the correct device ID, user name and password.

4. Click login to enter live view interface.

.

Note: To successfully remote access your system, the device ID should be ONLINE.

.

2. Access from PC Client (CMS)

1. Please download CMS from the below link:

http://www.tontonsecurity.com/download/page_show_67.html

2. Login user: admin, password: (default: NO password, please keep it blank)

3. Please enter “Add” to add device, you can add it “By IP/DDNS” or By Cloud ID”

4. By IP/DDNS:

IP/DDNS: (Enter NVR’s System Setup-Network Setup to find IP)

Port: (default: 80)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

Device name: Choose a name for your system of your choice.

Type: choose “NVR”.

Number of Channels: please input the correct number of the channels.

Click “Finish” and go back to “Preview”, click the device name to view live video.

5. By Cloud ID:

Cloud ID: (Enter NVR’s System Setup-Network Setup to find IP)

Username: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

Device name: Choose a name for your system of your choice.

Type: choose “NVR”.

Number of Channels: please input the correct number of the channels.

Click “Finish” and go back to “Preview”, click the device name to view live video.

Add the IP camera to the NVR by matching code

1.  When you use Match Code
1.1 Add new add-on cameras to your system
1.2 Re-pair camera to NVR when they lose connection. You need to delete the
Network Unreachable channel at first, then re-pair the camera to an unoccupied
channel. (unoccupied channel always shows No Video Source under Status.)

Tips: The IP cameras in pre-packed kits have already been paired to the NVR. So the
cameras will automatically connect to the NVR once they are plugged in power.

2.  Add camera by matching code.
2.1  Power on the camera which has no video, and connect this camera to the NVR
via Network cable.

.

2.2  Right click mouse on the main interface, select “Video Manage“

2.3  Click “Refresh“, find the camera’s IP. Click “Match Code“, then click “Yes“, the
NVR will start to match code to the camera.

.

2.4  After matching code successfully, the “status” will show “Connect success“.

Then you will see the camera is added to the NVR and display video on the screen.

.

What is the WiFi distance of the wireless kits?

.

Between each camera to the NVR:

In open space we tested 350m (1150ft) working distance;

With normal obstacles like 1-2 walls, we tested 35m (115ft) working distance.

For distance we only have theoretical values.

No certain distance can be guaranteed due to different environments applied in.

It varies depending on obstacles and signal interference.

on the contrast, if there are many blocks and signal interference between, the distance could be closer. 

.

What if your NVR system keeps beeping?

1. Please right click your NVR mouse, then click System Setup – General Setup – Error setup, make sure that “Enable” and “Buzzer” are unchecked.

2. Please right click your NVR mouse, then click System setup – Channel setup –  Video detection, make sure that “Buzzer” is unchecked for all channels.

3. If you have checked above 2, and none of the buzzer are checked.

    Follow below to stop the beeping:

    a. Right click your NVR mouse, then click System setup – System Admin –  Factory setting, uncheck WiFi Reset, then click Apply to reset NVR settings.

    b. If you cannot view the cameras on the NVR after resetting, please right click your NVR mouse, then click Exit system, choose shutdown. Follow on-screen message to unplug NVR from power and then re-plug it back to NVR. Wait for NVR to initialize.

Then the cameras shall come back.

.

How to upgrade the NVR system

.

.

1. Please download the update file to your computer and unzip it, then plug the USB flash drive,and move the unzipped update file to the root directory of the USB flash drive. 

Note: 

1)Please move the update file to the root directory of the USB flash drive, do not move the subdirectory.

2)Do not change the file name.

.

.

2. Connect USB-disk/mouse and USB hub with NVR shown as flowing.

.

.

3. Enter the NVR’s menu (System setup\System Admin\System upgrade),
Click “Start” to begin upgrading.
.

Note: Please keep power supply well during the upgrade.

.

.

4. Once the upgrade is done, NVR will restart system automatically.

.

.

How to view playback on NVR system

.

1. Right click the mouse , choose video playback

.

2. In the menu bar on the right, choose record type/channel/data to search what
you want to and click playback.

.

3. Click Backup and the video will be saved in USB storage

.

How to Add C8601 Cameras to Tonton NVR System

.

Document

.

or

.

Video

.

How to connect and set up the Wireless Network Camera System?

.

.

1. Connect the DC 12V/2A power adapter to the Power port of the NVR.

When Power indicator light is on, NVR starts to work.

2. Use VGA / HDMI cable to connect your NVR and Monitor / TV, then preview interface can be seen.

3. Plug the network cable and mouse to the ports of NVR rear panel.

4. Connect the DC 12V/1A power adapter to the IP camera (IPC).

Each camera has one 6ft length power adapter.

5. After finish connecting, the NVR will search the IPC automatically and start to initialize the connection.

When completed connection, the images will display.

6. Login this system:

Username :  admin

Password:  (there is no password, please keep it blank)

(Note: if you want to change the password, you can go to NVR’s System Setup – System Admin -User management – Set password to change it.)

7. Then you can follow up the below steps to set up on your phone:

If you want to view the cameras remotely, the NVR should be connected WAN network, Please ensure DHCP in your Router is open.

If you don’t know how to enable the Router’s DHCP, please input the IP Address of your  

Router to IE browser, then you will find the network information, you can enable the “DHCP”.

After that, please go to NVR’s System Setup – Network Setup to enable “DHCP”

Then the system will obtain the IP Address, DNS from your Router automatically.

Or you can go back main menu to select “Fast Network”, Then the system will connect the WAN network automatically.

8.   Access from smartphone

(1). Please download “Eseecloud” app from App store or Google play on your phone.

    (2). If install and open “Eseecloud” app at the first time, an account need to be registered initially.

(3) Add the device.

Method 1: Add the device via QR code.

.

.

Method 2: Add by cloud ID.

Cloud ID: Enter NVR’s System Setup – Network Setup to input Cloud ID or Scan QR Code)

Device name: Choose a name for your system of your choice.

User Name: Enter the NVR’s User Name (default: admin)

Password: Enter the NVR’s Password (default: NO password)

.

.

.

Method 3: Add by LAN scan.

Please make sure you are connected to the same wifi.

.

.

9. Access from remote PC (Log in with Cloud ID)

    PC : our item only support IE browser, please input “www.e-seenet.com” to IE Browser to view your cameras.

       Cloud ID: (Enter NVR’s System Setup – Network Setup to input ID or Scan QR Code)

       Username: Enter the NVR’s User Name (default: admin)

       Password: Enter the NVR’s Password (default: NO password)

(Input the correct Cloud ID, user name and password, click login to enter live view interface.)

.

NVR video backup.

1.Right click mouse > select Video backup.

.

2. Enter into the interface of Video backup.

   Select Channel, Record mode and Search time.

   Click “Search”. After that, the chosen video will display in the list.

3. Select the section which you want to backup.

   Then, click the bottom “Backup”.

4. Next, there will pop up a dialog box asking are you sure to backup this record.

   Click “Yes” if you are sure.

   Before start to backup, system will inform you to insert U disk within one minute. 

   If you want to cancel the operation of backup, you can click “Cancel” to withdraw.

   NOTE: The NVR only one USB port, so you have to unplug the mouse

and plug the U disk within one minute.

5. After you insert U disk, what you should do is just wait a moment.

6. Backup is completed when system inform you “Backup record succeed“.

   And you can unplug your USB disk at that time.

.

How to setup audio function?

1. System connection

(1) The monitor must have HDMI input port.

  (2) Connect the HDMI port on both sides with the included HDMI cable.

2. NVR setup

  (1) Choose the option “Private” on this interface during NVR’s restarting. It allows you select audio or not.

(2) Check whether the encode mode is “AV stream” or not.

(3) On the live window, click mouse to select any channel to pop-up the hidden volume icon like a speaker, click it repeatedly to hear or mute the sound from camera.

.

How to use a new Gmail mailbox account to set NVR mail alarms?

How to use a new Gmail mailbox account to set NVR mail alarms?

1.Register a new Gmail mail account, and log in.

2.Get into your mailbox>click the “” in top right of page>get into “My Account“.

3.     Click “Sign-in&security” and enter the interface,Turn on “Allow less secure APP on“.

4.  After that, you will receive an email from Google, which means “less secure sign in” has been turned on.

5. Get into NVR system. Right click mouse>select System setup>Network setup>Network Status.

   Check if your NVR’s network connected successfully.

   Before operate what mentioned above:

    Make sure Cloud(P2P) display “ONLINE“.

   Make sure the Network Status display “Healthy Network“.

6.Then, click the “E-Mail”. 

Input your Gmail SMTP Server (smtp.gmail.com) in ” SMTP Server” Input your Gmail account in “Username” and “Sender”.

Change the “Encryption Type” to “TLS”.

Input your Gmail password in “Password”

Input your two inbox address in “Sendee 1\2” 

After that, click “Apply”>click “Test”.

7.        When the system remind you “Test successful”, which means NVR’s mail alarm is set successfully.

8. PIR video detection setting as below picture:

    (1). Click “Channel setup” and “Video detection”

    (2). Choose Motion Detection, disable it

(3). Choose PIR Input Armed Detection, Enable E-mail Notice

9. After finished setting, When alarm is triggered, you will receive email from NVR.

PIR alarm setting

Only PIR detection recording setup

1.      Disable motion detection function, click ok to save

2.      Choose Detection Model with PIR Input Armed.

Please noted: If you want to set Buzzer, Email notice or App alarm, you can enable them, in this way, you will get notification on email or App.

3.      Press “Reset” to clear default setting

.

4.      Click the icon “Alarm”

5.      Press and drag the left button of the mouse to select needed schedule.

6.      Click ok to save

7.      Cancel the manual recording mode

.

.

.

8.      Once the PIR detection is trigged, the live window will display an icon like below, it means PIR recording is running

.

How to Reset NVR’s Password

Reset NVR’s Password

1. The interface when you log in. 

 2. Click “OK”. If you input incorrect password,

     monitor will display “Username/Password Is Incorrect!”.

 3. Continuously and successively click left button and right button in blank space of prompt box for six times.After that, monitor will display “Restore default user”.

4. Click “Yes”, and you will access to the interface where you can reset NVR’s password.

Tips:   1. The username must be “admin”, or else the password won’t be retrieved.

           2. If you want to make new password, please leave it blank in column of “Old password”.

           3. Delete the old password after reset the new one.

           4. If you have set a new password for NVR, remember that NVR password cannot exceed 10 characters, or the NVR will not save it correctly.

.

 reset NVR’s password             click to download video

How to install iSmkit PC client 

.

How to install iSmkit PC client                  Click here to download

Gmail Mail Configuration Guide

(DE) Gmail Mail-Konfiguration Anleitung 

click here to download

.

(FR) Guide de configuration de Gmail Mail 

click here to download

.

(CN) Gmail邮件配置指南操作步骤20230922

click here to download

.

(EN) Gmail Mail Configuration Guide 

click here to download

.

Email SMTP and POP3 settings

.

click here to download

.

Solve the problem of the white light always on(Applicable to 3.6.60 and above Version)

Precautions:

1. Please check your IPC version first, only 3.6.60 and above version can be solved the problem through upgrade.

2. The camera must be able to produce the image, if the camera can’t be viewed or resetted, it can’t be upgraded.

.

Check IPC Version:

Go to “System Admin” – “IPC Maintenance” to check the version of the problem camera. Please note: Don’t upggrade the version 3.6.16 and below version with these upgard file.

.

Download the upggrade file:

For 3.6.60 Version: Download Link

For: 3.6.60 Above Version: Download Link

.

Upgrade Method

1. Upgrade the IPC via NVR system

（1）Please download the update file to your computer and unzip it, then copy the update file(IPCAKV3C_xxxxx.rom) to a USB flash drive. Please note: Don’t change the file name

（2）Plug the USB flash drive to the NVR’s USB interface

Enter the NVR’s menu (System Setup-> Channel Setup-> IPC Upgrade)

.

.

（4）Click the “Channel” and select the upgarde channel of the IPC.

.

（5）Click “Start” and “Yes”, the IPC will be upgrading. Please note: During the upgrade, please don’t power off the NVR and the camera.

.

.

（6）If the camera upgraded successfully, the Status will show “Success!”.

.

.

2. Upgrade the IPC via TF card.

.

.

（1）Unzip the upgrade file, then copy the “help.rom” file to the TF card. Please don’t change the file name and move it to the root directory, do not move the subdirectory.

（2）Power off the camera, then insert the TF card to the TF card slot. Then power on the camera.

（3）Waiting for about 1 minutes, the camera will start up. Then press 3 times continuously of the reset button for the camera(In order to prevent operation errors, you can press several times, which will not affect the upgrade).

（4）About 2 seconds later, the camera will makes a sound for an upgrade. Then waiting for about 2-3 minutes, if the camera restart and works normally, it means that the upgrade is successful.

New Manual for Dual light

Click here to download

If the IP camera doesn’t work with NVR system,please check …

1. First of all,please confirm both of the camera and the NVR are powered on .

(1) Camera is powered on: Please plug the power adapter to the camera ,and then cover the IR-Cut with your hand (See picture), finally to check if the night vision will be activated or not .

(2) NVR is powered on : Please plug the adapter to the NVR ,and then see whether the power indicator is on.

.

.

.

.

2. Secondly please enter NVR system — Video Manage ,and check if the status of camera is connected successfully or disconnected. 

.

.

.

3. Thirdly, if the camera is disconnected,please confirm the distance of the camera and NVR system. The far distance will affect the signal transmission.Please follow the below steps to fix the issue:

.

(1) . Please enter NVR system —  Video Manage — delete camera (The same page as the Step 2)

(2). Remove the camera and take it next to the NVR system,and prepare a network cable and start to match code for the camera and the NVR.

(3). How to Match code :

A. Connect this camera to the NVR via Network cable.

B. Right click mouse on the main interface, select “Video Manage“

C .Click “Refresh“, find the camera’s IP. Click “Match Code“, then click “Yes“, the NVR will start to match code to the camera.

.

.

D. After matching code successfully, the “status” will show “Connect success“.Then you will see the camera is added to the NVR and display video on the screen.

.

4. Finally, you could unplug network cable and put the camera to the place where you want .

How to change the channel

.

.

1.Please click “Video Manage”.

.

.

2.Make a note of the camera IP address you want to change.

.

.

3.Click “Manual Edit” and enter the IP address on the corresponding channel.

.

.

How to fix black screen Monitor for 10” /15.6”NVR

click here to download the operation video

.

How to get the NVR system ONLINE?

.

1. Please make sure you enabled DHCP of your Router.

2. If you don’t know how to enable the Router’s DHCP,

    please input the IP Address of your Router to your computer browser,

    then you will find the network information, you can enable the “DHCP”.

3. After that, please plug a network cable to the WAN port on back of NVR.

4. If the system refuses to go ONLINE?

Basic troubleshooting:

  (1).  Check if your network cable can work well.

         If NVR is getting signal, there should be flash light. If not, please check the connection and cable.

  (2).  If the port is right and NVR is still OFFLINE, then it should be DHCP issue.

         Enable DHCP on your NVR.

        Click right button of mouse, go to NVR’s System Setup – Network Setup – check the DHCP and enable it,

        apply and save it. Wait for 1 minute to see if the status on bottom right corner changes to ONLINE.

5. Or you can go back main menu to select “Fast Network“, 

        Then the system will connect the WAN network automatically.

        Within 1 minute, you shall see NVR status changes to ONLINE and the NVR is ready to be viewed

        from anywhere anytime.

6. If this can’t help you, probably your Router disabled DHCP or block new devices from connecting.

    What DHCP does is: when Router find new device connected, DHCP allocate new IP to the device

                              and connect it to the Internet.

   An easiest way to know if your router enables DHCP:

   When you connect a new device to your WiFi for Internet service (or a visitor/ friend wanted WiFi

   connection), does it require WiFi password only? If only password required, then your router has

   DHCP enabled; if that requires not only password but also some settings, then your Router is secured

   from connecting new devices. Please ask people who secured the WiFi (who set password) to enable

   the NVR to connect.

The Step 4 and Step 5 should enable 95% users to get NVR ONLINE.

Even if the status shows OFFLINE after all this, we suggest you to use APP and access the Cloud ID

to see if it works.

Note:   Always wait for 1 minute after any change.

.

Advanced troubleshooting

If the basic steps above does not solve the issue. Follow below steps to do further troubleshooting.

1. Make sure the cable you connect to NVR has Internet access. 

Please use a laptop or any PC has RJ45 port

· Disable the wireless connection of laptop.

· Unplug the network cable from NVR and plug it into the PC, see if the PC can access the Internet via the cable.

· If it does, then the cable is good; if it does not, change a cable.

· If cable is good yet no Internet connection, please ask help from your network administrator

· to give the cable Internet access.

2. Enable DHCP of your router, please refer to Step 2.

.

If you don’t want to use DHCP, or you want to set up a static IP Address for your NVR system,

you can follow the below steps to set up:

   Well, we can allocate IP manually for the NVR and connect it to Internet. 

  1. Know your router gateway. 

  This is the IP that goes to the menu of your router. 

  This will vary slightly from manufacturer to manufacturer, and will be listed in the documentation.

  Here are some common IP addresses for various routers:

   Linksys, 3Com, Asus, Dell, US Robotics: 192.168.1.1

   Qwest (AKA CenturyLink), DLink, Netgear, Trendnet, Senao: 192.168.0.1