This is a user guide for CMSClient version V1.00.00.47, it’s applied to software version is equal or newer than V1.00.00.47. If you are running older version (e.g. V1.00.00.46, V1.00.00.45), please download and upgrade your existing one to the latest. It should be noted that Yoosee has no app be compatible with Windows smartphone. If you have a smartphone running Windows OS, obviously you can not use Yoosee camera. The Yoosee software team will not release App for Windows based smartphone.

What CMSClient does?

CMSClient provides users a centralized video surveillance solution. It allows users to manage multiple cameras simultaneously, users can preview, record, playback, even receive alarm alerts by using it.  Users also can change yoosee camera’s network settings (such as IP address, gateway, DNS), can shift recording video resolution from SD to HD, can modify camera’s password.

Installation of CMSClient software

The software doesn’t contain any virus, if your anti-virus software report virus warning, please check if you have downloaded the software from official website. The software requires permission to access your network/Internet, it uses RTSP stream protocol to communicate with cameras locally, and P2P protocol to communicate with Internet cameras. When installing the software, ensuring it allows to pass Windows firewall.  The software will keep communicating with remote servers intending to establish P2P connection, it doesn’t spy your video, doesn’t transmit/upload any video clips to remote servers.

Logon CMSClient Software

CMSClient software now allows users to login through three different types of account.

• Admin login: local login, don’t require users to register an account. No need to input password, click “OK” to login immediately. The software can automatically discover local cameras, but can not discover Internet cameras.
• Phone Number login: remote login with your registered yoosee account, after logon, the software will list added cameras in your account.
• Mail/user ID login: remote login with your registered yoosee account, after logon, the software will list added cameras belongs to your account.

Moreover, select either “Phone number login” or “Mail/user ID login”, the software can receive motion detection (or sensor triggered) alert to computer. When motion detection alarm occurs, the software will pop-up a new window automatically to alert users, it also can play selectable audible automatically to remind users.

How to add Yoosee Cameras?

After logon, CMSClient will automatically discover local connected cameras, click “Add all” to add them into your software. Please note the displayed p2p password and rtsp password default is “qwe123”, it’s an incorrect password, just ignore them.

Except adding automatically, users can click “+” icon on the left bottom to manually add cameras. In “Device manager” window, local connected cameras will be listed on the left column, click “>>” button can add to software which will appear in right column. Click “Manual add device”, you can add local connected cameras via entering device ID, device password, RTSP password. Click”Add shared device” to add cameras as a guest user. In pop-up windows, you should paste the shared link. To know how to get shared link, you can read this article – How to use Yoosee App’s sharing function?

How to use CMSClient software?

Once you added devices to software, you’re able to use each functions of it. Select device you want to manage, right click mouse will pop-up a menu list.

• Device property: change camera name, device password, rtsp password and group.
• Delete node: delete camera from this list/software.
• Start monitoring: start to preview real-time video (if it shows you a crying face, it means password is incorrect)
• Smooth/standard definition/high definition: before click start monitoring, you should choose default image resolution, smooth equals low resolution, standard definition equals VGA (640×480), HD equals 1280×720 or 1920×1080.
• IPC config: you’re able to tweak camera’s network settings (e.g. IP address, DNS), record video resolution (SD, or HD), password.  It only works on the premise that your camera’s password is correct. If you encounter “network timeout” “permission error” “password incorrect” error, to solve this, you need to logon software with yoosee registered account.

CMSClient Playback Function

You’re able to playback recorded video clips right from your computer. The CMSClient can only allows users to play remotely and locally recorded video clips, but also can allow you convert them to friendly .mp4 files which can be recognized and played by regular media players.

Click “Search” button on the left top, the camera can search files, click the file name to playback. Additionally, you can click folder icon to open a file to play it. All yoosee camera will record video with .av file extension. These raw files can not be recognized or played by regular media players, you can use the converter which the software has included to convert .av files to .mp4 files.

If you don’t want to install and use CMSClient software, still want to play .av files in another computer, you can read this article – How to play .264 video files from IP cameras/DVRs/NVRs?

CMSClient software is a powerful video surveillance management tool, it includes other function to provide a great flexibility. Click gear icon on the top of software, it will pop-up a “CMS config” window.

• File save path: select the folder path to store recorded video footage.
• Reserve space: allowing users to modify reserved space for video storage in your HDD.
• Record time for package: the time length to patch a video file when recording video. If the value is “60” min, the software will patch/generate a video file in every hour when software is recording on computer.
• Cycle record: turn on/off over-write function, automatically erase/overwrite HDD when space is full.
• Auto start record when monitoring: record video while watch video stream.
• Connect all of device automatically: automatically display video for all cameras/channels after logon software.
• Render mode: Directdraw, GDI
• Monitor: auto, rtsp, p2p
• Message notification: choose whether receiving message notification or not when there is a motion detection alarm.

If you logon software with registered yoosee account, the software will have “Alarm trigger” option. This open allows you to select time length of pop-up video when alarm occurs. You’re able to choose different audio files, the computer will play the audio to remind users.

<p>The post User guide for Yoosee App PC Software – CMSClient first appeared on NVR IPCAMERA SECURITY.</p>

Once you have the NAS setup you can come back to this post and follow the steps below:
.

Step 1: Login to your Synology NAS via a browser​

Step 2: Click the Package Center icon​

Step 3: Search for and install the Surveillance Station software (it should be on the home page of the package center, if not you can use the search bar to find it)​

Step 4: Click the Synology main menu at the top left of your screen and open the newly installed Surveillance Station software​

Step 5: Click the IP Camera icon​

Step 6: Click the add button when the new window open and then click add camera from the drop-down​

Step 7: Select Quick Setup and then click the next button​

Step 8: Enter the camera details manually or click the Search icon next the IP Address box​

Step 9: Check both the Synology Supported Cameras and ONVIF lists (some camera models are not directly supported by Synology, but as long as the camera is ONVIF compliant you should be able to add it to the Surveillance Station software)​

Step 10: Select the camera you want to add from one of the lists and click OK​

Step 11: Check that all the camera details are filled in, including the cameras username & password (also give the camera a unique name to help you identify it from other cameras)​

Step 12: Click the Test Connection button and if the test is successful you’ll get a green tick and a live shot from the camera, you can then click Finish and the camera will be added to your Synology NAS​

If the test is not successful you will have to go back and check the camera’s settings are correct, the most common problem is that the camera has an IP address that is not on your network, after you have followed our instructions from a previous video on how to change the IP address you should get a successful connection and be able to add the camera.

How To Install Synology Surveillance Station

Read Also : Dahua NVR Troubleshoot All Series

.

If you need more help with installing Surveillance Station and adding an IP Camera to your Synology NAS you can watch this video:

.

Synology NVRs and VisualStation​

NVR1218, DVA1622, DVA3221, VS360HD

NVR’s (Network Video Recorders) are a neccessary part of any security setup.
They work to store, playback and support the live feed of security footage from connected IP Cameras, and with Synology, can offer even more.

.

Offering a range of Network Video Recording solutions, from their energy efficient NVR1218, and compact VS360HD, to their deep learning, AI powered DVA series, Synology’s selection of NVRs were designed to appeal to a range of different users and applications.
At Use-IP you can now choose from these four Synology NVRs and decide which is best suited for your needs.
​

.

.

​

NVR1218​

The Synology NVR1218 is a 2-Bay (Reaching a max. of 7 bays, with an Expansion unit) Network Video Recorder, able to support a max. of 12 IP camera channels.
Its design is also fit for a PC-less experiance (only needing to be connected to a monitor) and can be accessed remotely, via Synology’s Surveillance Station, or, DS cam mobile application (allowing for Live view, playback, adjustments, and notifications, on a mobile device).

Key Features:
.

.

.

​

​

Deep Learning NVR (DVA) Series​

The Deep Learning NVR Series combines the Management features of Synology’s Surveillnace Station, with Advanced Analytics, designed to fit deployments of all sizes.
Intelligent Analytics – Included in DVA NVRs to strengthen on-premises security, offering deep learning algorithms and detection profiles
.

Users can choose between the more compact design of the DVA1622, or the larger storage of the DVA3221, the key features of which are both listed below.
​

DVA1622

DVA3221​

.

The DVA Series NVRs also come equipped with the use of Dynamic Maps, allowing for improved situational awareness, and to help users to determine camera/event locations, and provide instant access to video feeds for more efficient site monitoring. This also includes the features listed below:​

.

.

VisualStation

VS360HD
​

Synology’s VisualStation offers a PC-less, live view and playback solution, for your surveillance footage, with the ability to work in mobile environments.
Designed to work as a companion system, the VisualStation also offers an ultra-compact design, and features Synology SurveillanceStation live view and management tools. It is a perfect alternative for a Video recording solution, for users facing budget or space constraints.

Key Features:
.

How It Works:
Plug in an Ethernet cable, connect the VisualStation to a LCD-monitor or TV, log into the Synology SurveillanceStation – and its all set up, for quick and easy use.
.

The VS360HD is also equipped for use in harsh and mobile environments. With a design free from mechanical moving parts, the VisualStation is more resistant against vibration and hardware failure, than other Network Video Recording solutions.
Its design also features a solid outer case, built to keep it running in industrial temperature ranges (-20°c ~ 50°c)
This is what makes the Synology VisualStation both a cost effective, and reliable system, for any user.

.

Synology NAS/SAN Systems​

Synology’s Data Storage/Management Systems come in a range of styles and sizes, each designed to fit different user needs. Being able to appeal to a range of users and suitable for numerous applications, Synology’s NAS/SAN Systems are an ideal addition to any personal data management, business data management, or security setup.
Choose from Synology’s range of NAS types; RackStations, DiskStations, FlashStations, and more.​

What is a NAS?​

NAS = Network Attatched Storage.
A NAS is a device that provides users with a networked location to store their data, and are designed to be equipped for use at home or for businesses (or other applications).
But a Synology NAS has even more to offer, as they are designed to offer private cloud storage, backup systems, and secure file sharing.
​

Benefits For Home Use

The DiskStation Manager 7.0​

The DiskStation Manager is the operating system for Synology NAS systems, it was designed with focus on reliability and impressive performance, and offers users a wide range of data management features.​

Users can also feel secure when using their Synology NAS, as the DiskStation Manager offers Secure Sign-in, with app-based login approval, hardware security keys, and 2-factor authentication options. Keep your data, and your data management, as secure as possible.

.

Data Backup Solutions​

With the DiskStation Manager as its operating system, a Synology NAS will also offer users a selection of effective and reliable backup solutions, which include:
.

Active Backup for Business
Expands user data protection with agent-based Linux backup, possible for five major distributions, and AES-256 encryption.

Active Backup for Microsoft 365 / Google Workspace
Maintain offsite copies and restart backup tasks in a different location.

Hyper Backup
Protect data with backup support for DSM settings and 12 additional software packages.

Synology C2
Synology’s Cloud Storage Solution
Back-up NAS data to the cloud (with Hyper backup), and, sync requested data between C2 storage and branch offices (with Hybrid share)
​

Synology NAS Systems also include the Btrfs File System, that allows for even more backup solutions, so users can keep their data as secure as possible (keeping data safe even in the event of data corruption or system failure). These Solutions include:
.

.

.

.

Synology’s NAS Lineup
Now Avaliable at Use-IP​

​

RackStations​

A selection of Rackmount style NAS Systems.
Synology RackStations offer impressive performance and large storage space, all in a rackmount design.
​

XS+/XS Series – RS4021xs+, RS3621xs+, RS3621RPxs, RS1619xs+
+ Series – RS422+, RS820+, RS820RP+, RS1221+, RS1221RP+, RS2421+, RS2421RP+, RS2821RP+
Value Series – RS819
.

DiskStations​

A style of NAS perfect for a Desktop application.
Synology DiskStations range from being compact storage solutions for Business environments, to being an ideal starting point for Home users.
.

​

XS+/XS Series – DS3622xs+, DS1621xs+
+ Series – DS220+, DS420+, DS620slim, DS720+, DS920+, DS1522+, DS1621+, DS1821+, DS2422+
j Series – DS220j
.

FlashStations​

Synology’s FS Series, with an All Flash Array, Rackmount design.
Synology FlashStations offer uncomromising performance, and solid-state drives. Perfect for more demanding applications, and to accelerate Business operations.
.

FS Series – FS6400, FS3600, FS3400, FS2500

.

SA, HD, and, UC Series​

All in a Rackmount style, these NAS systems appeal to a range of storage requirements.​

SA Series – Offers a Scalable storage solution (ideal for enterprises) with high-performance and capacity requirements. – SA3600, SA3400, SA3200D
HD Series – Offers a High-density SAS Storage server, designed for Rapid data scaling, optimizing operational efficiency, and IT infrastructure.- HD6500
UC Series – Offers a dependable high-avaliability SAN Storage solution, fit for iSCSI and FC environments. – UC3200

.

.

​

Expansion Units​

Synology NAS/SAN Systems can also be expanded, with compatible Synology Expansion Units.
Increase your storage space by adding additional drive bays, using a range of Expansion Unit models, also avaliable at Use-IP

FX2421 – Expansion for FS6400, FS3600, and, FS3400
RX6022sas – Expansion for HD6500
RXD1219sas – Expansion for SA3200D and UC3200
DX1222 – Expansion for DS3622xs+ and DS2422+
RX1222sas – Expansion for SA3600 and SA3400

<p>The post How To Install Synology Surveillance Station first appeared on NVR IPCAMERA SECURITY.</p>

As the latest technology of Meeso Communications, H.265X has the advantages of low bit rate and low cost, it will surely stand out in the new round of market competition and achieve a new leap.

Add H265X Camera to Recoder

Read More :

1. XMEYE NVR Installation Guide
2. How to connect an IP camera to the XMEYE JFEYE DVR?
3. XMEYE Devices Password Reset New Method

In this article, I will show you how to add H.265X compression standard Camera to Dahua, Kbvision video recorder.

1. Settings on Camera

To add a Camera to a Dahua, Kbvision DVR, you need to adjust a few parameters as follows:

2. Add Camera to Recoder

After you have set the parameters on the Camera, you can add the following to the Recoder:

3. Check results

Here’s what you get when you’ve added the recorder:

A. View Camera on Web Browser

• Watch the main stream live:

• Watch live substream:

• Review recording:

B. View Camera on TV screen (HDMI/VGA)

• Watch the main stream live:

• Preview sub-stream:

• Review recording:

C. View Camera on SmartPSS software (PC)

• Go to main stream:

• Preview sub-stream:

• Review recording:

D. View Camera on DMSS (Phone) software

• Live view of main stream, sub stream and replay recording:

Thanks for following this post!!!

<p>The post Add H265X Camera to Recoder first appeared on NVR IPCAMERA SECURITY.</p>

Recorder Initialization & Password Reset – New Recorder Interface

This guide will walk you through initializing the recorder properly so the password can be reset by the client without sending a technician onsite. If the Initialization steps are not done correctly, the only way to reset the password is to call IC Realtime Technical Support and use a Backdoor Password at the recorder. The steps below require a monitor or TV (HDMI or VGA) connected directly to the recorder, as well as a USB mouse.

IC Realtime Password Reset

Read Next : Hikvision Devices password reset all methods guide

Recorder Initialization

• When the recorder boots up the first time, you will see the Device Initialization window come up. The first screen has you choose a Location (Country), Language, and Video Standard. The most important option is the Video Standard. It needs to be set to NTSC for use in the United States. When the settings are verified correct, click the Next button.

• The 2nd window allows you to select your Time Zone and manually enter your time. Verify your settings and click the Next button.

• On the following page, you will set the device password for the admin user account. You will be have to enter a password that has a minimum of 8 characters. Passwords are case-sensitive, and you can use letters, numbers, and the symbols found along the top row of the onscreen keyboard. NOTE: Some software (ConfigTool on Mac OS, for example) will not allow you to use anything other than letters and numbers for the password. A minimum 8-character password with a combination of letters and numbers is sufficient for security purposes, as our recorders are less susceptible to Brute-force password attacks than other devices due to the account lockout. The Prompt Question field is used to create a password reminder, which can be viewed from the login screen once the recorder has been initialized.

• The next step is to create an Unlock Pattern connecting at least 4 of the 9 dots in a  3×3 grid. The pattern can be used in lieu of using the username & password on the local monitor. Left-click & hold the left mouse button to draw the pattern. If you choose to draw the pattern, you will be asked to draw it once, then draw it again to set it. Once you draw the pattern a second time, the screen will automatically change to the Password Protection screen. If you choose not to use the pattern, click the Skip button.

• The last step in the process is THE MOST IMPORTANT STEP if you wish to prevent the need for a backdoor password. You will be asked to choose and answer 3 Security Questions that will allow you or your client to reset the password. You may choose meaningful questions and answer them with unique answers, or you may choose to give the same answer to each question. Each question has a number of options, which can be accessed by left-clicking once anywhere in the Question field. If you choose not to set the Security Questions, click the Green button next to Security Questions to disable them. When you are finished with the Security Questions, click the Save button to continue.

• After the Device Initialization is complete, you will be taken through the Startup Wizard. Using the Startup Wizard will guide you through enabling auto-updates (although this is an option on our recorders, we do NOT yet have an upgrade server that will push out firmware updates to our cameras or recorders), general settings, Network Time Protocol (NTP) & Daylight Saving Time (DST), Network, P2P, Basic, Encode, and Schedule settings for your recorder. All of the Settings in the Startup Wizard can be configured later using the main menu. When you finish the Startup Wizard, click the OK button when you see the Thank you for purchasing our product prompt, and your recorder is ready to go.

Password Reset

• To reset a forgotten password, right-click on the screen to bring up the System Login window. Click either the Forgot Pattern or Switch User buttons to go to the traditional login screen. There are icons to the right of both the User Name and Password fields. The icon next to User Name will show the Prompt Question that was set when the password was established when the mouse hovers over the icon. If the password is still unknown, click the Forgot Password icon to the right of the Password field . This will bring up the Reset Password – Security Questions screen, shown below. 

• Type the Security Question answers into their respective fields (answers are case-sensitive), then click the Next button. On the next screen, you will be asked to enter & confirm your new password for the admin account. Enter the password in the boxes next to New Password and Confirm Password, then click the Save button. 

• If the password is accepted, you will see the Successfully reset password message. Click OK on that message, and you will be taken to the System Login screen, where you will need to type your new password to access the settings. 

• Enter your new password to login.

Resetting a Recorder Password and Taking Ownership

Table of Contents

• Acquiring an Unlock Code
• Prerequisites
• Security Question Login Method
• Unlock Code Login Method
• Password Management
• Best Practices

Acquiring an Unlock Code

Users that no longer have credentials to login will need to fill out a Forgot My Password request using this link. An iCare specialist will work with you to facilitate this and provide an unlock code.

Prerequisites

• Serial Number of unit (This will be needed to generate Unlock Codes for units purchased after 2016)
• Date the recorder is currently set to (This is important in generating the proper Unlock Code as well)
• HDMI Monitor and USB Mouse attached to Recorder.  Login must be completed using the local GUI system. (Unlock Codes will not work through web GUI or software)

Security Question Login Method (If you have set Security Questions)

1. Using a mouse attached to the Recorder, right click and select “Main Menu”. This will populate the login screen. Click on “Forgot Pattern” as shown on image below.
   
   
2. Click on the “Forgot Pattern” as shown below.
   

   

3.  Answer the security questions then click “Next.”
   
4.  If answered correctly, you will be prompted to create a new password and to confirm the new password as shown below:
   

Unlock Code Login Method (If not using Security Questions Method)

1. Using a mouse attached to the Recorder, right click and select “Main menu”. This will populate the login screen. If your login screen requires a pattern, click on “Forgot Pattern” as shown on image below. Otherwise move to the next step.
   
   
2. Login with username “admin” and the Unlock code (or one of the unlock codes) given.
   
   
3. If successful, you may have a prompt populate as shown below. If so, create a new password under “New Password”  and type in the same password under “Confirm Password.” You can also create a Password Hint. The new password setup is now complete. If you do not have this prompt, you will be logged in to the Main Menu (as admin). Follow the next steps.
   
   
4. In the Main Menu, go to Settings > System > Account. Click on “Add User” as shown below. You will need to create an new admin level account (group level set to admin) to modify the “admin” account. This is because user accounts cannot be modified if they are currently logged in.
   
   
5.  Once you have created a new account, right click and go to Main Menu. Select “Shutdown” and then under the drop down, select “Logout” or “Logout Menu User” as shown below. This will log you out of the “admin” account so you can login with the new account that was set up in the previous step.
   
   
6. Right click then select “Main Menu.” Login with the new account that was set up in Step 4 then go to Settings > System > Account. Click on the “admin” account then click on “Modify”
   
   
7. Under “Old Password”, input the Unlock Code. Input a new password under “new Password” and copy that password under “Confirm Password.” Click “Save” when done.

Password Management

The management of usernames and passwords lies solely with the end customer. It is their responsibility to document and save these credentials.  IC Realtime does not save your device login information and is not able to provide any user created or changed user names or passwords. IC Realtime strongly urges end customers to document security system credentials in some type of password management system, like KeePass or LastPass.

Best Practices

• Document all of your credentials in a Password Management System, like KeePass or LastPass.
• When setting up a new recorder, follow the Initialization process and answer the security questions. In the event of a lost password, the security questions can be answered to reset the admin password (the security questions can be the same answers. It is recommended to document the questions and answers as well)
• Create a different admin level user / account as a backup as well as different accounts for lower level user access only.
• Setup a password Hint. If you have this option, creating a password hint will help to remember the password.

<p>The post IC Realtime Password Reset first appeared on NVR IPCAMERA SECURITY.</p>

For version : 3.0.3.0 if it doesn’t notice the password is incorrect , pls make sure you used the wired mouse, due to 3.0.3.0 version doesn’t support wireless mouse.

Note:User name and password should not exceed 8 characters and should not contain such as &*! @ (… #% and other special characters

You can refer to our YouTube channel videos : https://youtu.be/KJpJnYFlGK8

1) Within the black area, Click the left mouse button>right mouse button>left click>right click… Lasts 6 times

 

2) Yes

 

3) Input your new password,The old password is empty,you don’t need enter anything.

HiSeeu Wireless Camera System installation guide

Read Next : Hisilicon IP Camera Firmware Update

 

4) OK

 

 5) If this step still not work, please email Johnny@hiseeu.com with below screenshot of your NVR, then they will send you the super password to login

 

How to solve the problem of camera connect failed?

Please follow these steps to troubleshoot

Please check if the white antenna on the camera is loose first.

1)Cover the sensor under lens on the camera to see if the light is lit or not.

If it’s bright, it means camera is not bad.

If it’s not lit,You can connect the power of a good camera to the bad camera.

 

In the case of determining that camera is not broken.

2）right-click the mouse> video manage> Refresh / Search

3) if your camera with reset button, no LAN port, please take camera close to your NVR

1. delete the connect failed channel

2. press the reset button on camera for 10 seconds

3.Right click the mouse again > wireless add > wait the screen show a new camera IP address 172.20.14.**

4. if no IP address, pls reset camera for several times,

After adding the camera successfully, you can exit the add camera interface

below is the video for you check :https://youtu.be/Kaxvth-sd-Y

4) if your camera with Lan port

Pls use an Ethernet cable connect the camera to your NVR.

Delete the connect failed Channel>Refresh(Search) find IP address 192.168.**.**>Match Code(wait for IP address change to 172.20.14.**)

After that you can unplug the Ethernet cable.

You can refer to this youtube video.

https://youtu.be/kmNnFgjLiPI

HDD not fund / Not record anything

 Please refer to these below to solve the HDD not fund issue.

1）Check the power adapter connected to the NVR box. The NVR box uses 12V 2A or 12V 3A power supply. If you connect the 12V 1A cameras’ power supply to the NVR, the NVR box will not provide enough power to drive the hard drive.

2) If hard drive is preinstalled, there are 4 screws at the bottom of NVR box.

3）Check Hard Drive Information on NVR box and Format it

Right click the mouse>system setup>General setup>HDD setup>select the hard disk>Click Format, if the progress bar always shows a few percent or the formatting is failed, please contact with us.

 

 

4) Please open the NVR with a screwdriver, check the two cables connecting the hard drive and see if they are loose.

 

5）Take the hard disk out and install it on your computer. Check if the computer can recognize the hard disk. This is to confrim the HDD is the problem or not.

How to solve Gateway Unreachable or Network Error

If you click “fast network” to appear: Gateway Unreachable or Network Error , pls fellow below steps:

Step 1:

1) you must check if the network line is faulty or not: check whether the switch and router line connection are correct.

2) Can you connect to the external network normally through the computer wired connection?

Notice: Do not directly connect the recorder to the fiber

 

Step 2: Right click mouse and choose Fast Network —-> Auto config ,check if the network will be healthy or not

 

Step 3: If the auto config still can’t make it work , pls kindly check the same network computer network setting

Then “manual configuration” set the recorder network settings, don’t choose DHCP, input the same IP address and gateway and submask same as your computer

Offline

1)Pls Connect NVR to your router with an Ethernet cable. After that right click the mouse > Fast network.

 

2)If Step 1 doesn’t work, Maybe the Ethernet cable is damaged. Please replace it with a new one

3)If there is no problem with the cable.

Pls right click the mouse> system setup >Network setup>Do not choose DHCP>Change DNS to 114.114.114.114 or 8.8.8.8 > Power off the NVR and power on again(Reboot the NVR)

4)You can also connect the NVR to your home WiFi,

Enter the wireless internet interface > Select your home WiFi and enter your password > Apply

Change the display channel of the camera

When you select the corresponding channel, you can click the two buttons on the left, and then move the channel

You can also drag the image directly to another channel

How to set up Motion Detection？

1)Enable Motion Detectin on NVR Monitor

Pls right click the mouse>system setup>Channel Setup>Video detection>Selecting the Channel for Motion Detection>Choose the form of alarm>After you set it up you can Click “Copy to” to set to all channel

 

2) Set the area of motion detection to be set within the field of view of the camera.

 

3)App Alarm

a)Select App Alarm on NVR

b)Click three dot> Alarm push

 

c)Click System authority settings, turn on all permission of the app.

 

How can I view the camera remotely?

There are four methods to view the camera system remotely. Please refer to these step below.

 

1) First you need to connect the NVR with your router by wired or WiFi

Wired connection

1. wired connection, connect the NVR with router by ethernet cable

2. right click your NVR mouse choose fast network, then click auto config, check cloud ID status is online and network is healthy, then you can remotely check the system on your phone app

3. if not online and healthy network, please click manual configure, and check your router detail,

make sure the NVR and your router is the same IP gateway, IP address the first 3 number should be the same, the last one can’t be the same ,. preferred DNS please change to 8.8.8.8 and apply it

WiFi connection

1. please notes our NVR only can work with 2.4Ghz wifi network,

2. right click your NVR mouse choose system setup–network setup–wireless internet –enable wireless LAN, then find your house wifi name, input password, apply it

（please note the wifi name can not included any special character ,such as “_”, otherwise it will show connected failed.）

3. check the status is connect failed or success, if it is failed, please click view details,

check the same wifi network details on your phone and your NVR, then change them to the same IP gateway, IP address the first 3 number should be the same, the last one can’t be the same ,. preferred DNS please change to 8.8.8.8 and apply it

https://www.hiseeu.com/a/help/article/27632

2）To view on the Phone

a) Setup NVR box

Please reset your password：right click mouse>system setup>system admin>user>setuppassword>change a new password(Password must be within 8 characters)

b) Setup Mobile Phone

Scan below code download “Eseecloud”

 

 

c) Click “+”–“other way to add/scan the QR code on your NVR fast network page “–input cloud ID user name is admin and password is the one you login in NVR (If you doesn’t change the user name and password, User Name is admin password is the one you set for the NVR before), if your forget the password please refer this step: https://www.hiseeu.com/a/help/article/27650

(Cloud ID is in the lower right corner of the screen or right click your NVR mouse and choose fast network to find Cloud ID)

 

 

Scan the QR code on display

 

The user name is admin, enter the password of your camera system in the password field

 

3）To view via Eseecloud software on PC

EseeCloud for Windows PC

Eseecloud MAC: http://download.dvr163.com/tool/EseeCloud-mac-2.0.8_20200228.zip

Eseecloud Windows: http://download.dvr163.com/tool/eseecloud/EseeCloud_Setup_3.0.7.10.exe

here is the video to check how to add it : https://youtu.be/0AX1-sMKJG4

If you have registered your eseecloud account on your mobile phone, you can directly log in with your eseecloud account on the computer, and the account information will be automatically synchronized to the PC software

 

Double Click Cloud ID

 

How to remove the red triangle mark

For the red triangle mark it is for notice you something happened for your camera

such as the motion detection , video loss, HDD not found,

for remove the triangle

1. you need upgrade your NVR version to 3.0.5.0

there are 2 ways to upgrade

1) online upgrade, connect the NVR with router by LAN cable , right click your NVR mouse and choose system setup–system admin–system upgrade–online upgrade

2) offline upgrade, you need copy the firmware to the USB disk and choose local upgrade the firmware you cane email Johnny@hiseeu.com to get it

3) after you upgrade successfully, pls right click your NVR mouse and choose system setup–general setup–error setup–disable alarm icon.

Connect the camera to WiFi, then add it to NVR

You can connect the camera to your home wif and then add it to NVR.

First you need to press the reset button for 6s on the camera to reset the camera,

1) Please refer to pages 4 to 6 of the manual in the attachment to connect the camera directly to your mobile app,

 

 

 

 

２）First, you need to connect NVR to your router,

Then search the NVR for the camera connected to WiFi

Right Click the mouse > Video manage > Change the “protocol” to “onvif” > Search > Add one

 

if it show Password Error, please go to your phone app , click “…”–“Edit” then on blank place quickly click 6 time you will see cameras password here, go back to NVR video manage page, select the correct channel, click Manual Edit to input camera password .

What to do when the screen color is not displayed correctly

1） Click the mouse to select the screen –> click the 3rd icon (color adjust)

2) Click Default button–>select Ircut mode–>Ok

If it doesn’t solve your problem ,pls send this screenshot to us

Audio function！

1:Please check if there is a microphone hole on the back of the camera.

 

 

2:When you want to use the audio function of the camera, you need to turn on the audio function of the camera:(left click your mouse on the camera images)

3: right click your mouse — turn up the volume

4: Also turn on the audio button on App

 

 

if your version is 3.0 ,you should choose the AV stream also,refer these step

right-click the mouse ->System Setup->Channel Setup ->Encode Setup ->Select orresponding Channel(1-8) ->change the Encode Mode to AV Stream -> Apply

 

5: Every camera supports audio, but you can only use the audio of one camera at the same time.

and if the NVR your had order is with monitor, pls plug in your headphones or stereos behind the NVR

 

Why can’t remotely check the playback and change the setting

pls fellow below step

right click your mouse and choose system setup –system admin–user–edit user– choose remote and config and playback

How to solve the problem of camera lost connect with NVR, need reboot the camera to fix this problem?

Firmware 1: https://www.dropbox.com/s/qlyr53xfsrjscox/%E9%87%8D%E5%90%AF%E7%9B%B8%E6%9C%BA%E5%9B%BA%E4%BB%B6.rar?dl=0

 

IPCAKV3W_20220415_3_6_82_572011

IPCAKV3W_20220415_3_6_82_572011

(Fix the camera lost connection with NVR need unplug camera power cable)

Firmware 2: https://www.dropbox.com/s/mrdzs1ioqhmuuve/%E4%B9%9D%E5%AE%89%E5%8D%95%E6%9C%BA%E4%BF%A1%E5%8F%B7%E4%BC%98%E5%8C%96%E5%9B%BA%E4%BB%B6.rar?dl=0

 

IPCAKV3C_20220415_3_6_82_572010

IPCAKV3W_20220415_3_6_82_572011

(Fix camera signal problem)

 

572010 for the camera model: 5322-W

572011 for the camera model: 5323-W

please go to video manage page to confirm the camera model.

 

To upgrade the camera firmware: download the firmware from the dropbox, unzip the file at first, copy the correct file to your USB DISK root, format should be FAT32,go to system setup–channel setup—IPC upgrade page–click the correct channel–click start–remove mouse –insert USB disk–wait for camera upgrade successfully

I’ve connected everything, but the display doesn’t show images

Pls Refer to the following steps

1）Press the left mouse button for 30 seconds and the camera system will reboot.

2）A)You need use a VGA cable to connect the NVR to the monitor.

B)If you don’t have a VGA cable but have another monitor, you can connect the camera system to another monitor.

3）Then change the output resolution of NVR.(Right click the mouse>system setup>General setup>Screen setup>Output resolution)

Set an appropriate resolution and switch back to the original HDMI Cable.

4）If the display is still not displayed, you can choose another resolution.

if your NVR box version is 3.03.0 pls change the step 2 as below：

2) Then change the output resolution of NVR.(Right click the mouse>system setup>General setup>Display Resolution)

If camera often loses signal with NVR？

You can use the following four methods to solve the problem of poor camera signal

Please check if the white antenna on the camera is loose first.

1)First, you can change the wireless channel of the camera system to ‘other’, and the antenna of NVR is better to stand up

Right click > system setup > Network setup > change Wireless channel to “other” > Apply

Then restart the NVR, unplug the power supply of the NVR and plug it in again

2）You can replace the white antenna on the camera with the black extension antenna in the package, so that the black extension antenna passes through the wall.

 

Place the camera next to the NVR to ensure that there is a good signal between the camera and the NVR.

3）You can set a camera as a WiFi repeater to enhance the signal between the camera and the NVR.

4）You can also buy a WIFI repeater, which also enhances the signal between the camera and the NVR.

for Wifi repeater you can search: B07NRBYM5C on amazon.

If you can write a good rating to our camera system,We can send you one for no charge.

(warm notes:if your version is 3.0,there is “Search”button but not “refresh” ,click the “search” but the “refresh”)

(version 3.0)

How to use the wifi repeater to enhance signal

 

When the repeater is powered on, its indicator lights up.

Press the reset key for 10 seconds and it will deletes all previous matching records

How to use it on NVR.

1)Connect the repeater to NVR by Ethernet cable

2)click “Search” and then there will disappare a device which IP address is “192.xx.xx.xx”

Click it, it will pop up a new window

click Match button to let the status become “wireless has been matched”

 

At this point, you can unplug the Ethernet cable.

4) back to the Video Manage interface and click the Repeater .it will show the same window as the figure below.

click the add icon after the Router button,then select chanal which you want to enhance sigal

How to add an extra camera?

when you receive the new camera , there is no match between the nvr box and the new camera. You need to pair them.

if your camera with reset botton , no Ethernet port,

1)right click your NVR mouse and choose wireless add

2)press the camera reset botton for 10 seconds

3)wait it shows camera IP address 172.20.14.**

4)if no IP address, pls reset camera for several times, then you can exit,

below is the video for you check

https://youtu.be/Kaxvth-sd-Y

 

if your camera with Ethernet port, You can refer to our video on Youtube.

https://youtu.be/kmNnFgjLiPI

1) You need to connect the camera and the NVR box with the Ethernet cable.

2)Right-clik the mouse video manage→Refresh/search( find camera IP address as 192.168.1.**)→Match code( wait camera IP address changed to 172.20.14.**) then exit and choose add one

After camera and NVR are paired, you can unplug the Ethernet Cable.

3) Use the same way to pair more camera.

How to solve “Resolution too big”?

Our system upgraded , the “Resolution too big” camera is 3MP, old system can’t work with 3MP camera

1. right click your NVR mouse choose system admin–system version to check NVR version is 2.8 version or 3.0 version

2. if it is 3.0 version, you can upgrade it to latest firmware then it can support 3MP cameras (3.0.6.0 version and above version)

how to upgrade to NVR?

1) Online upgrade : go to system admin-system upgrade-then click online upgrade, wait for it upgrade successfully, then camera will show image

2) Offline upgrade, please email Johnny@hiseeu.com with your system version page , then she can provide firmware to you

3. if it is 2.8 version,the only way can fix is to upgrade camera firmware

right click your NVR mouse–system setup–system admin–IPC maintance, then take a screenshot of camera version, email : johnny@hiseeu.com for resolution too big problem.

4. after you get the firmware, please copy to your USB DISK root, format should be FAT32,go to IPC maintance page–click the correct channel–click start–remove mouse –insert USB disk–wait for camera upgrade successfully

5. go to system setup–channel setup–encode setup–find correct channel–change resolution from 2304*1296 to 1920*1080.

How to Change the Display Position of Channel

There are 2 ways to changed the position of camera

 

1)Generally speaking, we will choose four channels to display at the same time on the screen

 

For convenience, let’s first choose to have all channels displayed on the screen.

right click your mouse — Split Screen — X8 View

 

Now we want to let the Channel 7 to the Channel 2 position

left click the mouse on the channel 7 screen and dont loose

then move to the channel 2 position ,loose the mouse left key

 

that is OK

2)Please wrote down the IP address of the camera (which you want to exchange it channel,such as channel 5). Then deleted the channel which you want that camera to place(such as channel 2), did a manual edit on channel 2 ,Enable it and change or add the IP address of channel 5 wrote down. Camera immediately came up on channel 2.

App wrong Password

Pls refer to these step to solve the wrong password issue. refer this video : http://youtu.be/bFVwGqnr2Js

1)If you doesn’t change the User Name and the Password on NVR box.

The User name is ‘admin’, no password (you needn’t input anything)

 

 

 

2)For change the password on NVR box.

Right click the mouse>system setup> system admin>User>set password

 

3)User name and password should not exceed 8 characters and should not contain such as &*! @ (… #% and other special characters (you can setup password: jasmi985/ jasmi996/ jasmi856 or others. )

If you can login NVR with a password, but can’t login on App, please confirm that the password within 8 characters

Note：App login username and password are different from the camera login username and password. They are two different sets of username and password system.

How to set up Email notification?

a. Enable POP/IMAP in your email. If default setting of your E-mail enables that, please skip this step.

Login your email via browsers; go to Settings – Forwarding and POP/IMAP-Enable POP and IMAP – Save Changes.

 

We also need to Allow 2-Step Verification for your Gmail account, login www.google.com

 

• Open your Google Account.
• Select Security.
• Under “Signing in to Google,” select 2-Step Verification and then Get started.
• Follow the on-screen steps.
• Normally after you set 2-step verification, you will create a new password on NVR password page you need input this password

b. Go to your system main menu. System setting- Channel setting- Video Detection. Enable E-mail Notification and click Copy to apply the same setting to other channels.

 

b. Go to your system main menu. System setting- Network setting- Email setting. You will see the interface shown below.

 

c. Follow the instruction below to input the information required to finish the setting.

 

Email Notificaion: Check “Enable”

SMPT Provider: Click the one you use in the selection. Or click USER CUSTOMIZE to use the E-mail server that is not in the selection.

Sender : Type in your sender email address

Password: the password of login your sender emial address

SMTP service: when you choose the correct SMTP provider, it will suggest correct service to you

Port: The default port is 25. If it doesn’t work, you can go to the link below to get the port of the e-mail you use.

https://www.arclab.com/en/kb/e … .html

Encryption Type: Select the one that your E-mail server works. If there is no selection, please choose None.

Sendee 1: the email you want to receive email alerts

Sendee 2: the second email you want to receive email alerts, you can leave it blank

 

d. Then click Test see if you can receive a test e-mail alerts from Esee. If yes, that means the setting has set successfully. Then, please click Apply to save the setting.

e. Latest APP allow to set email notification on the cellphone directly

Go to cellphoen app Eseecloud, click me–settings–mail to receive alert messages–enable it, then put your gmail address, to get verfication code, after you input verfication code click confirm, then you will get the email notification, thanks

 

 

 

 

 

How to setup Record Plan?

You can set up three modes of record plan

Note：After you have set up the record plan, you need to click “copy to” to apply the record plan to all channels.

1) Time Recording:

Setup period of time of recording on NVR,Right Click the mouse>System Setup>Record Setup>Record Plan.

Click Time and put mouse icon on the upper left corner(for example 1 as picture shows).press and drag the mouse to the right to choose the time.the list will turn to red.

2) Motion Recording:

Only detect motion and then start recording. Right click mouse>System Setup>Record Setup>Record Plan.

Click Motion and putr mouse icon on the upper left corner, press and drag the mouse to the right to choose the time. The list will turn to green.

3) Alarm Recording:

Riht click the mouse>System setup>Record Setup>Record Plan.

Click Alarm and put mouse icon on the upper left corner,Press and drag the mouse to the choose the time,The list will turn to yellow.

Note: Users can Setup any period of time they want, for example 0:00:00-23:59:59, That’s 24hrs*7days recording. When NVR detects hard disk, the default setting will be 24hrs*7days recording.

The priority of Alarm is higher than that of Motion, and the priority of Motion is higher than that of Time.

When you have set the corresponding record mode, you can click “select all”, and the time area below will become the corresponding color

Video Playback

Right clik the mouse>Video Playback>Choose date、Channel、record mode>Click Search>then can view playback file

Note：You can only watch four Channels recording at the same time.

1. IIIustration for playback button:

play,

pause:

fast forward*2,*4,*8；

2. Play file: Choose the recording file in file list,as number“1”shown in picture. Chooseone of the recording, click“play”to play to recording file;

3. Video backup: Choose the recording file in file list,as number“1”shown inpicture.insert the U flash disk, click“video backup”to backup the file;

4. Timeline: Click“date”and“time”at left bottom to check the timeline of recording, as number“2”shown in picture;

5. On the timeline with recording file,left click the mouse, the can playbackthe file.

How to watch the playback on my phone?

First ,you should install the Eseecloud on your phone ，if you hadn’t installed it ,refer this link:

http://www.hiseeu.com/news/wirelessskitfaq/69.html

click playback

then it will show the interface follow below

choose the time and channel which you want to watch

Notes: The default is no sound when you watch playback.so you should click this sound button to open it if you want to hear

How to backup the recording

There are 2 ways to make backup

1) use USB disk to backup

1. right click your mouse, and choose video backup.

2. choose the channel/date/time playback you need backup,

(If you copy too much backup, we suggest you copy it one by one channel to save copy time)

3.Backup, the let your mouse out and within 30 seconds put the USB to get the backup

if you need check tbe playback you copy out on computer, pls use VLC player , you can download here :

http://download.dvr163.com/tool/Video-player%20.zip

 

pls notes USB disk format should be FAT32 otherwise your NVR may can’t find it.

 

2) make backup on computer

 

1. download Eseecloud :

Eseecloud MAC: http://download.dvr163.com/tool/EseeCloud-mac-2.0.8_20200228.zip

Eseecloud Windows: http://download.dvr163.com/tool/eseecloud/EseeCloud_Setup_3.0.7.10.exe

 

2. add the system to your Eseecloud phone account, then on computer software choose login cloud(login with the phone app Eseecloud account and password)

 

3. search the cameras playback, and choose the channel you want to make playback and wait for it shows the recording

 

4. click the download icon the chose the files you want to download, wait for it finished the process, then you can open the it and check the playback on computer

 

here is the video for you check : https://youtu.be/kR7QN_2UKdI

Factory Setting

Pls refer to these step below to reset system

1)Right click the mouse>System setup>System admin>factory setting

*Note: pls don’t check “Channel setup”&”Screen setup”&”Digital Channel”

Click “Apply”

2)If you Check “All”

After NVR Reboot,you need Right click again>video manage>Double-click the IP address of camera (like 172.20.14.2)

If Your NVR box version is 3.0.3.0

Pls refer to below steps

Right click the mouse>System setup>System admin>factory setting>simple restore

The standalone camera connection step

pls connect it step by step , if you fail , pls send us some screenshot and tell us which step is wrong by email or whatsApp

our email is :johnny@hiseeu.com

Wechat/WhatsApp:+86 13392810296

Skype:Johnny.chen1204

1) download “Eseecloud” app on your phone and register it

click add button and choose Standalone camera

 

2)check if the camera light lit

click this button

3) Point the camera of the mobile phone at the QR code of the camera

4）Choose a network environment for your camera, the WiFi name

5）input the wifi password and click the connecting device button

6) Wait a minute and it will connect succeed click COMPLETE button

7)edit the camera name and set its password(password can be empty )

that is finished! if you want change some camera information such as password, you can click setup button to set it

Here is video for you check how to connect it on phone app : https://youtu.be/tNKeWUfe-mI

How to fix there is no cloud ID

1. Connect the recorder to the same LAN as the computer ：connect to the router

2. Provide the IP address of the recorder, System Settings – Network Setup Photo

 

 

3. Recorder switching debugging mode: system setting – system management – system maintenance, right mouse click, pop-up dialog box, click the left mouse button in the blank space of this pop-up dialog box, right click, click the left and right button, 12 times, Find out if the font prompt toggles the debug version, click Yes, OK. Go back to the lower left corner of the main interface with a red font. Take a photo to us (2.8 version)

 4. Provide remote tool ID and password, manufacturer technology remote connection control and send the email to us

if you don’t have the remotely tool, you can send the email to us, so we can send to you

(3.0.3.0 version)

3.Recorder switching debugging mode: right click your mouse—system setup–general setup–time setup–change the Date format–right click your mouse, pop-up dialog box ,

click the left mouse button in the blank space of this pop-up dialog box, right click, click the left and right button, 12 times, Find out if the font prompt toggles the debug version, click Yes, OK. Go back to the lower left corner of the main interface with a red font. Take a photo to us.

How to contact amazon customer service?

1). Use your Amazon account to log into www.amazon.com

2).Pull down to the bottom of this page and find “Help” button , and click on it to get into a new page

3). Find “Need more help ” in the middle of this page and move it to this button and you will see “Contact Us ” and click on it .Then you will get in touch with Amazon Customer Service Associate.

4).Or you may choose to call the Customer-Service by number 866-216-1072

Add Device (412 camera system)

First you need to connect the camera system to your WiFi.

Click the home button.

 

 

Select your WiFi and enter wifi password

This string of numbers is cloud ID.

Then go to “Eseecloud” app

Networked devices

Input your cloud ID and User name(User name is admin) and password(Camera system has no password by default)

5MP WK-4HB315-1T TZ-HB315 Night Vision is not good,upgrade as below

Please download the firmware at this link :

https://www.dropbox.com/s/gcrg3xw7f42ylys/IPCAKV5C_20221011_3_6_97_572110hsy%281%29.rom?dl=0

After you get the firmware, please copy to your USB DISK root, format should be FAT32,

Pls right click your NVR mouse–System Setup–Channel Setup–IPC Upgrade–Select the correct channel–click start–remove mouse –insert USB disk–wait for camera upgrade successfully

How to solve Most of Network Status Problem?

Please right click NVR mouse choose Fast Network check Network Status

• Healthy network: Network connect successfully
• Gateway Unreachable: means NVR IP Gateway and IP address not in the same gateway as your router, Click Manual Config, then find your router correct IP gateway, such as 192.168.1.1, then IP address should be 192.168.1.***, last numbercan’t be the same as your router, change it on NVR. If you connect with wifi network, you need go to System Setup—Network Setup—Wireless Internet page click View Details and click Manually to change those information.
• Request DNS Error: disable DHCP, change the Preferred DNS to 8.8.8.8, reboot the NVR and router.
• Network Cable Disconnect: make sure the NVR connect with router by Ethernet cable
• Network Card Not Found: on Network Setup page find PPPoE disable it.
• Network Busy: disable DHCP, change the Preferred DNS to 8.8.8.8, reboot the NVR and router.

<p>The post HiSeeu Wireless Camera System installation guide first appeared on NVR IPCAMERA SECURITY.</p>

In this guide, we will go through all the steps related to setting up your newly acquired Uniview Security System.

Overview:

1. Access the NVR via a dedicated display.

2. Log in using the default credentials found on the product manual and update the password.

3. Install and pair the EZView app for mobile access anytime, anywhere.

4. Check the timezone and the device clocks for accurate alerts and scheduling.

5. Access the NVR via a browser from another device. Use EZTools to get the IP address.

6. Enable and configure NVR/camera features, alerts, and etc.

Setting up using Direct NVR Access

The NVR interface can be accessed directly by simply connecting the NVR to a display (this can be done with an HDMI or older VGA cable) and to a mouse. Once the display and the mouse is connected and the login screen is displayed, proceed to login. Since this is the first time, we will be using the default username and password (at the time of writing default login and password are admin and 123456) found on the manual that came with the NVR.

Load More :

• How to Setup IP Camera Uniview
• Uniview How to configure Face Recognition

After logging in, Uniview’s privacy policy will be shown for you to review. Once you have reviewed and accepted, you will immediately gain access to the NVR and cameras connected to it. But, since it is the first time we are logged in and we are still using the default credentials, we will be prompted to change the login information.  You will be using the new password for all your future access with the NVR.

Once the password has been changed, a pattern lock will also be prompted (this is optional and can be skipped). After doing so, the Privacy Policy will be displayed for the user to review. The screen that follows the Privacy Policy will let us connect our mobile devices to the NVR. This will grant access to Live View, alerts, and other configurations we may want.

The device QR code will be presented here. Allowing you access to the EZCloud feature. Devices can be added to the cloud manually but it is far easier to just use a link given from the QR code. If you want to pair the NVR with the EZView app, click here to read more about it.

The next step is to set or synchronize the time. This step will ensure that all scheduling configurations you will set and all alerts and alarm information will be accurate and will work based on your local time.

After this, you will be prompted to check the TCP/IP settings, the default settings will work for most people. If you need to specify networking (usually when DHCP is not enabled on other devices on the network), please do so here. You will still be able to alter this later.

Once the time and the password have been configured, you are now ready to enable and disable the features of the NVR.

To access the menu, you can right-click on any part of the screen and then click on Menu. It can also be accessed along with other options by moving your cursor to the bottom left of the screen. This will take you to the SETUP screen where you can enable and customise alerts, features, and other options available to you.

To read about each feature and how to enable and configure them, check out Uniview Setup: Everything You Need To Know.

Setting up using Remote Browser Interface

You can also access the NVR interface through the use of a browser on a device connected to the same network as the NVR. To do this, you will need the IP address of the NVR you wish to login to, and then enter it into the address bar in the browser. The easiest way to find the NVR’s IP address is by checking the “Network” settings tab, followed by the “Basic” tab, then the “TCP/IP” tab. You’ll need the IPv4 Address. In our case its 10.1.1.214 but it will likely be different for you.

Another way to find the IP address of your NVR is with Uniview’s EZTools which can be downloaded here. Once installed on your computer, running the EZtools will automatically show you all connected Uniview devices. The IP address can also be obtained by logging into your router and checking connected devices, using the command prompt (arp -a command and checking for new devices on the private network).

Note: Any browser should work to alter configurations, however using Internet Explorer will be the easiest to access the Live view. (Due to some newer browsers not supporting certain plugins).

From here, we can see the IP address given by our router to the NVR. 192.168.254.192. It will likely be different for you. Clicking on the Remote Web button will open your default browser and take you to the NVR interface.

You can then proceed to login to your Uniview NVR Interface. Since this is the first time, we will be using the default username and password found on the manual that came with the NVR. After logging in, Uniview’s privacy policy will be shown for you to review. Once you have reviewed and accepted, you will immediately gain access to the NVR and cameras connected to it. But, since it is the first time we are logged in and we are still using the default credentials, we will be prompted to change the login information. You will be using the new password for all your future access with the NVR.

Once the password has been updated, you will be greeted by the Live View display. Clicking on any of the cameras found on the left will show you live footage from it. In this case, a single IP camera is connected to the 4-Channel NVR.

From here, you can now click on SETUP to access all configurations and features and set them up to your preference.

To read about each feature and how to enable and configure them, check out Uniview Setup: Everything You Need To Know.

Before we end, we should connect the Uniview NVR to the EZView app for easy and convenient access. To do this, we will need the QR code of the device we want to add to an EZView account.

Navigate to Setup>Network>EZCloud

The device QR code will be presented here. Make sure that the EZCloud feature is enabled and that the device has access to the internet. Click here to read more about it.

EZView App Installation and Device Integration

With the QR code visible, we will need to install the official Uniview app from the playstore. To get EZView you can download and install it here for Android devices and here for iOS.

Android: EZView for Android
iOS: EZView for iOS

Once installed, the EZView app will need permissions to access your device storage to save and view the Live View and playback.

Once granted, the Service Agreement and the Privacy Policy will be presented for the user to review.

After this, you can proceed to create your own EZView account or login if you have an existing one. This is a separate account from the one specified in the NVR. You can choose a different or similar email. The email registered here will be designated as your account for EZView. The email registered on the NVR upon changing the password is for recovery purposes. You will be able to pair multiple devices to the same EZView account and gain live access to all of them.

Once logged in, you will then be taken to the Live View. This screen will not show any cameras at first as we still have not paired any NVR or camera to the EZView account. To add your NVR and cameras, click on the top right Devices icon.

This will take you to a list of all the devices on your account. Since we don’t have one yet, it will either be blank or sometimes, a demo device will be shown. Click on the Add Device (+) button on the top right to add your device.

Ensure that the NVR is connected to the Internet, then choose SCAN for a quick and easy way to pair your smartphone to your NVR.

You can then proceed to scan the QR code found on your NVR or on the display screen where we left off. Once scanned, you may now proceed to configure the device name and other options for your preference.

In this particular situation, I added a Uniview 4-Channel NVR. It is now shown on my devices list along with all the cameras connected to it. I named this NVR as 4CH-NVR. As you can see, the IP Camera attached to this NVR is now available for Live View.

Select the camera by checking the circle and tapping on the Start Live View at the bottom will take me back to the Live View. You will be able to select multiple video feeds from different devices on this screen.

Tapping on the top left icon will allow you to check other features and settings available to you, including alarm notifications and alerts, Playback, recording schedules as well as downloaded snippets of video and screenshots.

<p>The post How to Setup Your Uniview Security System first appeared on NVR IPCAMERA SECURITY.</p>

Remote Access – Basic Troubleshooting

If you’re having trouble with setting up your Swann unit for remote viewing, or the remote viewing was working but has since stopped, here are some simple steps for you to try.

1) Reboot the recorder or camera

Rebooting the device both clears the memory and sets up the basic network parameters of the recorder or camera again. This can help if the router has “lost” the device from the routing table or if the device requires a new local IP address.

2) Reboot the modem and/or network connection devices

There may be an issue with your modem or network connection that is preventing the Swann unit from contacting the internet correctly. Rebooting these devices can correct these issues.

3) Reconnect the network cable and/or try a different one

For some Swann units such as recorders, the network (Ethernet) cable connects your device to your internet connection devices such as a modem or a router. Sometimes the contacts may become loose requiring you to replug the cable for the recorder to start working again. We suggest testing the cable on a different LAN port, located behind your modem/router. If this also fails, then your cable may be defective and may need to be replaced. If you have a spare network cable lying around, try switching the cable to see if it helps.

4) Reset the recorder or camera

For recorders – While this step is rather drastic, it can also be of use where the recorder’s settings have been misconfigured or if you have changed or reconfigured your network or internet hardware. This will clear all the settings from your recorder, including your network settings which could be causing the issue with your local/remote access from phone or computer.

If this step seems like a lot of work to recover from, do not forget to export the settings of your recorder to a USB stick before you proceed. That way, if the reset does not correct the issue, you can easily recover the settings lost. Also, if the reset did solve the issue, you can reapply the settings to see if that was what caused the issue. Check your recorder’s user manual for configuration export instructions.

For Wi-Fi cameras – if your camera has settings related to network, it might also be misconfigured or something has changed internally. Be aware that there is no exporting of settings here therefore, if you will reset your camera, you might re-do the first time setup.

Load More :

1. Problems with Swann Security Cameras
2. Swann Latest Firmware Files Guide
3. Swann Security Password Reset All Model

Swann Security – Error: Device has been disposed

NOTE: This guide is for the following recorders : DVR-4480G, 4480RN, 4480V, 4580G, 4580RN, 4580V, 4680, 4680RN, 4680A, 4680X, 4680XN, 4685, 4685RN, 4780V, 4980, 5580, 5580A, 5580G, 5580G2, 5580RN, 5580RU, 5680, 5680A, 5680RN, 5680X, 5680XN, NVR-8580, 8580RN, 8780, 8780RN, NVW-650, 800

This error message means that the username and/or password you entered on the app doesn’t match your recorder’s credentials.

To resolve this, you need to go to the recorder itself and try to log in – this is to ensure that you have the right username and password of your unit. Once you have it, you may try to add the device again and carefully enter its credentials on the app. In summary, you need to: Select Pair Device. Scan its QR Code (either the sticker on top of your unit OR in Menu) Enter the recorder’s credentials (case sensitive).

You may find this video useful but most importantly, you need to have your recorder’s username and password with you as this is needed when pairing your recorder.

Setup Cloud storage to OS 5 recorders

NOTE: This guide is for the following recorders : DVR-4480G, 4480RN, 4480V, 4580G, 4580RN, 4580V, 4680, 4680RN, 4680A, 4680X, 4680XN, 4685, 4685RN, 4780V, 4980, 5580, 5580A, 5580G, 5580G2, 5580RN, 5580RU, 5680, 5680A, 5680RN, 5680X, 5680XN, NVR-8580, 8580RN, 8780, 8780RN, NVW-650, 800

Swann’s OS 5 recorders now has the feature to save images or recordings through Cloud which might be more accessible to you without being on the unit itself. This can serve as another way to get notified when there’s a movement detected on one of your cameras.

Couple of things to prepare:

1. Make sure to have a Dropbox account ready. If you don’t have one, visit Dropbox and register first.
2. Then make sure your recorder is connected to the internet. Not having this will obviously not send the recordings on the Cloud or even give you access online.

Setup

1. On Swann Security app, go to Menu > Dropbox.
2. Choose your recorder that you want to setup.
   
3. It will open Dropbox app or Dropbox website will open (depends on what you have) – make sure you are logged in to the Dropbox account where pictures or videos will be saved.
   
4. Allow – choose this to allow Swann Security to gain access on Dropbox.
5. COMPLETE! – it will go back to the Swann Security app once you chose Allow. Tap again the recorder and this message (image at the right) should appear.

In case it repeats step 3, just cancel it or go back, then you’ll see this message (image at the right).

 

Enable Cloud Notification

1. Go to Menu > Alarm > Detection
2. Click on Action
3. Enable Picture to Cloud or Video to Cloud on selected Channels.

…and you’re DONE! Now every time the recorder detects movement, it will then send it to your Dropbox.

Be aware of the following:

• Default Dropbox storage has limited storage space
• Not all channels can be selected to upload video
• Uploads to Dropbox consume upload data, be aware of potential additional charges when using an internet connection with caps/data usage charges
• Consider using the Overwrite option to select a timeframe that the Cloud storage uses, to keep the storage from filling up. Note that if the storage fills up before the Overwrite deadline, that it will operate the same as Auto
• Be aware that a desktop PC with the Dropbox software installed may download any recordings to the Dropbox folder on that PC

Password Reset for SwannBuzz Account

This article will guide you on how can you reset the password of your SwannBuzz account.

	Open SwannBuzz then tap Forgot Password? below the Password field.
	Enter your registered email address then tap Get New Password.
	Now check your email (even your Spam or Junk folder) to get the temporary password.   In the app, tap Return to Sign in
	Get the new password.   Go back to SwannBuzz app then log in using your email and new password.
	Once logged in, it will ask you to set a new password. Enter it on both text fields.   Tap OK and that will now be your new password.

NOTE: If you didn’t receive an email and you are using a private email similar to .gov or .edu emails, please contact your IT or the domain.

OutbackCam: Why detection angle different to viewing angle

The OutbackCam utilizes a passive infrared motion sensor so that the system is able to run in a stand-by mode. This means the battery life of the system is extended from what would otherwise be hours, into weeks and/or months. When activity is detected by the motion sensor, the camera component that was previously switched off is now activated and takes one or more snapshots. Due to the time difference between when motion is detected and when the camera is able to take its first photo, we have extended the detection angle so that an object moving through the shot will be captured despite the activation delay.

Having said that, passive infrared motion detection is not a flawless technology. You will get times where the sensor detects motion when there is none. When passive infrared motion detectors are used outdoors, there is a higher likelihood of false alarms due to a large number of varying environmental variables such as temperature, wind speed, time of day and lighting conditions.

If you believe this renders the system unusable, you could try using race tape (a.k.a. gaffer tape) to tape either side of the white passive infrared sensor until you have an acceptable detection angle.

How to get the MAC address of a recorder using an Android device?

If you forgot your password but needs to login to your recorder, you most probably need the MAC address of the recorder to enter. We have couple of articles to help you with that HERE but all of those require a computer.

This article will help you get the MAC address of your unit by the use of an Android device and a 3rd party app called Fing.

Scan this QR code and install the app:

or go to Playstore and search for Fing.

Once the app is installed, here are some requirements:

1. You must be at the location where the unit is.
2. The Android device must be connected to the same router where the recorder is connected.
3. You must have a monitor and mouse connected to the recorder to input the MAC address later.

Once you got your MAC Address, visit the article that is meant for your device HERE to know how to reset your password.

How to enable push notification of Swann apps in iOS?

Upon installation or while using the app, it will ask for some permissions to be allowed.

Check the instruction below if you chose Don’t Allow on the initial setup:

Phone Settings

1. Go to Settings on your phone and select Swann Security.
2. Enable Notification and Location – as for Location, choosing either Always or While using the app works fine.

App Settings

This applies to Swann Security only; go to the Menu then select Notification. Make sure it is enabled.

Recorder Settings

For recorders compatible to Swann Security, check this article: How to enable push notification on recorders with V8 firmware?

How to change the position of the Date and Time display bar on my DVR

You can adjust the position of the OSD from the menu display of the DVR. It has to be done directly from the DVR, using the monitor that is connected either to its VGA or HDMI output.

You simply open the menu of the DVR, go in the menu display, and then, from the camera tab, click on SET next to the OSD Display Position.

Afterward, with the mouse connected to the DVR, left click on the date and time display , hold down the button and drag the display wherever you wish .

The position chosen for the Date and Time Display will be reflected on the live view on your computer screen, should you access the DVR through the Network Interface ( and also on the recorded videos if you have enabled record date from the Display menu of the DVR ).

How do I improve my remote viewing performance?

If you’re experiencing any intermittent connectivity issues when streaming or playing back videos from your recorder, on either the computer software or phone app, then the problem may be related to a limitation with your internet connection speed.

It is important to consider the amount of bandwidth needed when viewing your cameras remotely.
Increasing the video quality of the stream also increases the amount of data needed to upload the video onto your phone or computer.

You can use this article to help you check your speed before continuing to adjust your settings.

The diagram below summarizes the data transfer process of when a video is being uploaded to the server and then downloaded onto the user’s phone.

1. The recorded video is encrypted and uploaded onto the server (internet)
2. The file is then downloaded onto the computer or phone.

This is why the download and upload rate is important when streaming videos from a remote location. The higher the quality of the recordings, the more data is needed to be upload onto the server.

There are a couple of things you can change on the recorder to help improve the streaming service.

1. Reduce the streaming quality, on the phone.
2. Reduce the sub-stream resolution and bitrate, on the recorder.

See instructions below.

Stream on Fluent

This step is necessary for us to use lower bandwidth when streaming the cameras.

You may want to keep in mind that the quality will be lower than expected to lessen intermittent connections and get a smoother experience when viewing the cameras.

These are the things you can do using the software or app.

• If you are accessing the recorder using SwannView Link software, click the Play button at the right and choose All channels fluent.
  
• If you are using SwannView Link app, tap Stream and choose Fluent.
  
• If you are accessing the recorder using SwannView Plus software, right-click on the recorder at the left side and choose Set Sub-Stream To All.
  
• If you are accessing the recorder using HomeSafe View software, right click on your recorder at the left, and choose Set Sub Stream to All.
  
• If you are accessing the recorder using HomeSafe View app, tap on the Stream icon and choose Substream.
  

<p>The post Swann Security Troubleshooting All Devices first appeared on NVR IPCAMERA SECURITY.</p>

• Username: admin
  Password: 123456

• What is the default IP address of your device?

  Both NVR and IP cameras have DHCP enabled by default. It will automatically pick up an IP address of the network when plugged into a network.

• Do you have any device discovery tools?

  Yes, Smart Utility is a device management tool that can detect the device’s IP address within the same network, perform general configuration toward the device, firmware upgrade, extract system’s log and etc.

• What are the video content analytic rules supported by your device?

  Each of IP camera support the following VCA

  • Crossing Line Detection
  • Intrusion Detection
  • Enter Area Detection

• Which VCA Rules will support the Turing Vision Cloud?

  Vision Cloud supports both Intrusion and Enter Area VCA Rules, Cross Line detection is not supported by the Vision Cloud.

• What display output does your NVR support and what is the max resolution to display?

  NVR has two local display ports – HDMI and VGA. The maximum resolution is 4K 30Hz. HDMI and VGA are synchronous displays. Both outputs display the same contents.

• Does each of your NVR come with the Turing Vision Bridge?

  Yes, all Smart Series NVR should be packaged with our Turing Vision Bridge. If you do not have the bridge, please contact us to send you a Turing Vision Bridge.

• What is the Turing Vision Bridge ? How does it work with your NVR?

  A Turing Vision Bridge is a device that sets up a connection for NVR to communicate to our Turing Vision Cloud service. For details, please contact our support, your regional Sales Manager or Sales Engineers.

Load More : How to set up battery powered Cameras

• How do I upgrade the firmware version of a Network Video Recorder (NVR)?

  • A1: Upgrade from a PC
    1. Download the NVR firmware from the banner message after logging into Vision Web Portal. Save the firmware to a known location in the computer.
    2. Access the NVR by entering the IP address of the NVR in the web browser.
    3. Type username and password to login to the NVR.
    4. Once login to the NVR,
       Click on “Setup” tab > Navigate side menu to Maintenance > Maintenance
    5. Under Maintenance > Select “Local Upgrade” tab
       Choose NVR as device type
       Click on the “Browse” button to browse the firmware saved in step one.
       Click on the “Upgrade” button to upgrade the firmware.
    6. There would be a firmware upgrade progress bar showing the upgrade process. Once it reaches 100%, NVR will reboot right after. Firmware has been successfully upgraded when NVR comes back from reboot.
  • A2: Upgrade from the local display of the NVR.
    1. Perform Step 1 from “Upgrade from a PC”. This time save the firmware to a USB flash drive.
    2. Once firmware has saved in the USB flash drive, remove the drive from the PC and insert it directly to any USB port of the NVR.
    3. Navigate NVR’s Local Display menu to
       Menu > Maintain > Upgrade
    4. Choose “Local” for the Type
       Click on the dropdown menu of the “Partition” to select the usb flash drive connected to the NVR.
    5. Select the firmware > click on “upgrade”
    6. There would be a firmware upgrade progress bar showing the upgrade process. Once it reaches 100%, NVR will reboot right after. Firmware has been successfully upgraded when NVR comes back from reboot.

• I have enabled Search People in Analytic. Why are some people not being shown in the People tab?
  Is there a limit of how many people I can run face search with?

  The reason can be that the face is too far away from the camera, or is facing away from the camera such that it will not yield a good face match result.
  There is no limit on the number of faces to be detected per customer account.

• What type of recording compression does your NVR support?

  H.264 and H.265 video compression are the compression supported by NVR.

• Is there a limit to how long the stream will stay active?

  Not at the moment.

• Are we using P2P to stream video to the cloud? When I request a live stream of video, what happens?

  Detected event videos are stored in the cloud and are accessible by the account user or administrator until they expire after 30 days. A recording playback is directly streamed from the NVR through the Bridge to the user’s browser.

• How many streams of video can I pull from one camera? What is the limit?

  20 streams per each smart series camera. When an IP camera is connected to a NVR, 3 of 20 streams will be occupied – Main Stream / Sub Stream / Third Stream.

• Can I assign permissions to the users?

  A user can be assigned permission to view cameras live, playback recording and edit cameras for the sites assigned to this user.

• Can an email be the main account for a bridge and the secondary account for a different bridge?

  No, one email address can only be associated with one account.

• How do I keep my bridge’s system and firmware up to date?

  Your Turing’s bridge can be upgraded via OTA (over-the-air). You will see a pop-up notification whenever a new version is available. To start the process, click “Upgrade” from the pop-up, or go to Settings, select the device you want to upgrade under “Devices”, and click the Upgrade button. 

• Where can I find configuration guides for legacy 3rd party camera installations?

  https://turing.ai/resources/turing-vision/user-manuals

• Cannot view 3rd party camera Live view on Turing NVR or Turing Vision but cameras show online.

  Check the encoding setting of the camera to see if you have enabled H.264+/H.265+ or any advanced compression technology. If YES, please turn it off. Advanced compression technology is proprietary and cannot be supported.

• How to add a brand new 3rd party camera into Turing Vision?

  Follow up with manufacturer’s installation guidelines to activate, setup cameras, turn on ONVIF, make sure 3rd party cameras are in the same LAN as Turing NVR. Then refer to Turing Legacy installation guidelines for the rest steps.

• Can I use the Turing NVR to Change the Third-Party camera settings?

  Generally, No. The ONVIF protocol can work with time and encoding but usually not with intrusion zone or motion detection settings. It is important to set them in both places to ensure the work.

• Do we utilize Main, Sub, and Third Stream in the Turing Vision Platform?

  Yes. The Main is for the HD streaming, the Sub is used as default up to 2*2, and Third is used >2*2.

• How long does it take for the camera settings in the Turing Vision Platform to update?

  It may take up to 5 mins to update the camera setting display here if you made any setting change on NVR or Camera. Please be patient with the updating of information to the cloud.

• Will there be any 3rd stream recommendations?

  Not exactly, usually the 3rd stream is the lowest resolution stream, compared to the main or sub stream. Just make sure the 3rd stream is lower than 720p.

• Cannot connect camera to NVR and it shows error message: user lock out.

  This is because some 3rd cameras have a protection mechanism if the user name/password is incorrect, you could either wait for a certain time period or simply reboot the camera.

Turing Vision Mobile App (Recommended)

Leveraging AI to reimagine the way improving safety, security, and operations

DOWNLOAD
(iOS)DOWNLOAD
(Android)

SMART Utility

Software utility on the Windows PC used to discover, upgrade, and modify parameters for the SMART series products on the same LAN.

DOWNLOAD
(Windows PC)ARCHIVE

SMART Station

Management client for the Windows PC and Mac. Allows for local LAN access. Computer hardware not included

DOWNLOAD
(MAC)DOWNLOAD
(WIN32)DOWNLOAD
(WIN64)Archive

SMART Player

The SMART Player is intended to play back video clips directly extract from the SMART series NVR.

DOWNLOAD
(Windows)

 

ADVANTAGE Tools

Software utility on the Windows PC used to discover, upgrade, and modify parameters for the ADVANTAGE series products on the same LAN

DOWNLOAD
(Windows PC)ARCHIVE

ADVANTAGE Viewer Mobile App

Easy-to-use mobile app for remotely viewing live and playback video peer-to-peer for the ADVANTAGE product family. Not part of the Turing Vision cloud platform.

DOWNLOAD
(iOS)DOWNLOAD
(Android)

ADVANTAGE Management Center

Server-client based management software for the Window PC. Allows for multi-site management and more advanced analytics. Server hardware not included.

DOWNLOAD
(Windows PC)ARCHIVE

 

Smart Installation

Quick Setup Guide

AI Technology

People Search

Turing Hardware and Software

Connection Illustration

Quick Start Guide (Hardware)

Quick Start Guide (Web Version)

Quick Start Guide (Mobile Version)

3rd Party Camera Integration Guides

Integration Guide for Axis Cameras

Integration Guide for Dahua Cameras

Integration Guide for Hanwha Cameras

Integration Guide for Hikvision Cameras 1: Replacing Hikvision Plug-and-Play NVR with Turing

Integration Guide for Hikvision Cameras 2: Using both Hikvision and Turing Plug-and-Play NVRs

Integration Guide for Hikvision Cameras 3: Using both Hikvision and Turing Non-Plug-and-Play NVRs

 

Turing Vision Web App

Comprehensive set of security, safety, and operations; respond to alerts in seconds – Instant AI-based alerts configured by event, camera, location, role or shifts; Search incidents across all historical data – Intuitive search to filter all events recorded.

LOGIN

 

Turing Vision Mobile App

Leveraging AI to reimagine the way improving safety, security, and operations

DOWNLOAD
(iOS)DOWNLOAD
(Android)

 

<p>The post Turing Vision General FAQ – frequently asked questions first appeared on NVR IPCAMERA SECURITY.</p>

<p>The post Add Interlogix IP Camera to Dahua Recorder first appeared on NVR IPCAMERA SECURITY.</p>

Type 1 system stuck in the upgrade interface

Please disconnect the Ethernet cable to the router, and default the system.

After rebooting the system and it works well, you need to set a new password and don’t use the default one.
Here is the link for password change in case you need:

The system’s default password is blank(nothing). We suggest you change the system’s default password when you hook up the system for the first time to protect your privacy.

Load More : Tutorial of General IP Security System

Below are instructions on how to change the password.

How to Change System’s Password?

1. Use the system’s user name admin and default password blank to log in system.

2. Right-click mouse and select the Main Menu:

3. Go to Advanced:

4. Go to Account:

4. select admin and click Modify Pwd:

5. Input the new password and confirm it. Since the old password is the default password which is blank, leave the old password box blank.

Click OK to save.

When you finished the step, you can plug the internet cable back.
One more tip, If you can close the DMZ and UPNP feature in your router, this problem will never happen.

Type 2 system stuck in the booting logo

Here are some methods for troubleshooting:
a). Please unplug the Ethernet cable from the system, then restart the system without Ethernet cable to have a try.
b). If still not working, Please remove the hard drive from the system, then power on the system separately to have a try.
c). If still not working, please use another power supply (with the same voltage) for the system to have a try. While the system comes back, kindly please change the password for your system, it seems the hack attract your device, please make the password a little complex. don’t easy as empty

Part 2

there is no signal on the monitor

1. Do you notice if the system gets power? if it gets power, the LED in front of the DVR will be lit up.
2. Did you hear a beep when the system powers on? It is very important.
3. Are you using the HDMI port on DVR to connect DVR to a monitor or TV? if yes, could you please try VGA port on DVR?
4. Make sure your TV is in the right mode, HDMI mode for HDMI cable, VGA mode for VGA cable, not any other mode. You can monitor the remote control to switch it.
5. Please remove the hard drive from the system, then power on the system separately to have a try.
6. Can you kindly change another power supply to have a try? you can use the cameras instead.
7. Please submit a request in the below link:

<p>The post Guide – DVR&NVR Stuck Issue first appeared on NVR IPCAMERA SECURITY.</p>