1, RTSP to add
1、main stream：rtsp://ip address/11
2、vice stream：rtsp://ip address/12
Find “FFMPEG (H264)” this column, fill in information of RTSP in the URL.After adding can test is successful

Go to “Camera” option.

Input your camera ip address, User name and Password, click “Finish”, add camera succeed.

PDF Download : How-to-add-CamHi-camera-to-Ispy-下载

CamHi Pro Tutorial Guide

Read Next : V380 IP Camera Installation Manual

The difference between camhi and camhipro

The camera can use camhi and camhipro app at the same time, camhipro’s interface design is more modern, except for the interface there is no other difference, the functions are the same.

CamHi Instructions for use

The following tutorials are only available for the CamHi app.

How to add the camera

Warm Tip: This product only supports 2.4 GHZ WIFI. Before adding devices, make sure that your router is 2.4 GHZ WIFI, and your mobile phone is connected to 2.4 GHZ WIFI.

First, connect the camera power supply. After about 40S, you will hear the device tinkling sound. If you do not hear the tinkling sound, please press RESET 10S at the device base. If the equipment does not have audio, please judge by time.

Note:

1. Please use the power adapter matched with the camera to avoid damage to the equipment.
2. Don’t plug in wiring for power-on equipment; (After plugging in wiring, you can’t configure WIFI with one key)
3. One-click configuration WIFI only supports some models, and some models do not support one-click configuration WIFI.
4. Box camera, Dome camera and other models use connection hotspots to configure WIFI. See AP connection operation instructions for details.

Wired connection (only applicable to the equipment with internet access)

(1) Please connect the network cable and the equipment cable interface. The other end of cable connects the router, and the camera is on, waits the startup and completes the self-inspection (If you fail to self-check, please press the recovery key for a long time to restore the factory settings.).

(2)Click “add camera” on APP’s main interface to select “add UID by scanning QR code” (QR code above XXXX-XXXXXX-XXXXXX out of the machine body) or “LAN search UID” after the mobile phone connects the WIFI.

(3) Click the modelxxxx-xxxxxx-xxxxx of camera occurred in the camera list.

⑷ Return to the camera list by clicking “√”, then the camera is displayed online, and conduct the preview by clicking the camera.

Wirelss Installation(only for devices with WIFI modules)

After installing the mobile phone software, the mobile phone connects to WIFI, clicks Add Camera >Wireless Installation> Enter WIFI Password >Do you hear the sound? The system will be equipped with WIFI if it has been selected properly. When the WIFI configuration is successful, there will be voice prompt. (If you don’t have audio equipment, please see the picture prompt)

(1) Network Camera in Network; Select the corresponding UID

(2) Enter the camera password (the default password for the camera is admin).

(3) Click the completion button in the upper right corner to complete the addition of the camera.

Hot-spot connection (only suitable for devices with WIFI modules)

(1) The camera is powered on and waits for the completion of the self-inspection (if it fails to do so, press the recovery key for a long time to restore the factory settings).

(2) Open the WIFI search, choose the name of WiFi beginning with IPCAM-xxxxx, and enter the original password 01234567 (if you change your password, enter your modified password) as follows:

(3) After successful connection, the method of use is the same as that of wired connection.

4G Connection (only for devices with 4G modules)

(1) 4-G hot spot connection is shown below. After completing the 4-G hot spot wireless connection, the second step of Anzhao wired connection method begins to connect the device, close WiFi, open data flow, click on the device to connect, or scan the serial number of the fuselage (SN two-dimensional code above the fuselage) to connect, click on the camera to preview, such as Figure:

Function introduction

Introduction to real-time preview interface

1.Mirroring inversion + picture reversal

2.Lens zooming-in+ zooming-out and focus

3.Setting and invocation of presetting bit

4.Camera mode (infrared mode +full-color pattern + intelligent model)

5.Off

6.Sound opening and speech pattern

7.Quick photo

8.VCR

9.HD model

Cloud deck and presetting

1. Cloud platform control

⑴ Click the sliding screen on the real-time watching interface to control the camera rotation.

2. Presetting

⑴ Click the presetting icon and enter the presetting management interface.

⑵ Add the presetting: Several presetting could be added with the limit of 255.

⑶ Delete the presetting: Edit the set presetting by clicking.

The preset shortcut command table

PTZ Dome Camera Instruction List

2.5 Inch WI-FI Dome Camera Instruction List

Function	Mode Of Operation	Function	Mode Of Operation
Camera universal address	Address code 255	group first cruise preset 1-8（Dwell time 5 seconds）	Call 65 Preset
Enable Preset cruise line	Call 71 Preset	group second cruise preset 9-16（Dwell time 10 seconds）	Call 66 Preset
A cruise preset for 4 seconds	Call 75 Preset	group third cruise preset 17-24（Dwell time 15 seconds）	Call 67 Preset
A cruise preset for 8 seconds	Call 76 Preset	group fourth cruise preset 25-32（Dwell time 20 seconds）	Call 68 Preset
A cruise preset for 10 seconds	Call 77 Preset	group fifth cruise preset 33-40（Dwell time 30 seconds）	Call 69 Preset
A cruise preset for 15 seconds	Call 78 Preset	Group sixth fourth cruise preset 41-48（Dwell time 60 seconds）	Call 70 Preset
A cruise preset for 20 seconds	Call 79 Preset	group seventh cruise preset 49-56（Dwell time 90 seconds）	Call 72 Preset
Set the limit point A left	Call 91 Preset	group seventh cruise preset 57-64（Dwell time 120 seconds））	Call 73 Preset
Set the limit point B right	Call 92 Preset	clear all of the presets	Call 77 Preset
To enable A, B two scans	Call 93 Preset	Start A ,B Low speed scan	Call 87 Preset
To clear A, B two scans	Call 94 Preset	Start A ,B medium speed scan	Call 88 Preset
A 360 – degree scan, and A, B two scanning speed	Call 65、66、67、68 Preset,  the corresponding rate of 3, 6 degrees per second, 9, 15 degrees and 40 degrees	Start A ,B fast scan	Call 89 Preset
clear all of the presets	Call 60 Preset	clear all of the preset	Call 90 Preset
360 degree scans  （Only applicable few model）	Call 99 Preset	Restore the factory	Call 94 Preset
Forced light off （Only applicable few model）	Call 88 Preset
Forced light on  （Only applicable few model）	Call 89 Preset
Auto control light  （Only applicable few model）	Call 90 Preset
Restore the factory	Call 96 Preset

Video playback and Download

Warm Tip: To watch and download remote videos, SD cards need to be inserted, while local videos are saved in the APP installation device.

1. Select the local or remote video to play, and control the playback speed. For example, select the local video, as shown in the figure:

2. Remote Video Download

Click on the video file in the video list interface, then click on download, the video file will be downloaded automatically. The downloaded video file will be saved in the local video-download interface. After the video download is completed, you can click on continue to download, continue to download other video files, or click to view, and automatically jump to the download record. Like an interface.

3. Remote Video Search
   In the video list interface, Search options are available to Video file length: 15-900 seconds can be set, default is 600 seconds.

select the video search range as needed.Note: Set the setting range on the reference software interface.

Note: Some models only support 15-600 seconds.

Alarm Setting

1.open the Alarm Setting

2.The Level settings;

High: Sensitivity value is more than 75;

Medium: Sensitivity value is about 50

low: Sensitivity value is less than 25.

Action with Alarm

1.Alarm Notification

Choose to turn on, indicating that the alarm will send a push message to the mobile phone.

2.Alarm SD REC

Select Open to Save Alarm Video to SD Card

3.E-mail Alarm with Pictures

Select to open, indicating that the alarm sent pictures to the designated mailbox

4.Save pictures to FTP server

Select Open to save alarm pictures to designated FTP server

5.Save videos to FTP SERVER

Select Open to send alarm video to designated FTP server

6.Picture num

Picture capture number 1-3 can be set up (part of the model support)

7.Set alarm ringing linkage

Choose to turn on, indicating that the camera will give an alarm sound when alarming, the type of sound, the duration of the call can be selected (part of the model support)

FTP Setting

1.Server Address：Fill in the erected FTP address.

2.Server Port：Fill in the port of FTP.

3.User Name and Password Fill in User Name and Password Setted in FTP Server.

4.After filling in, click the APPLY; finally, you can click the TEST FTP SETTOMGS to check whether you can send the picture to the FTP server.

Audio Setting and Video Setting

1.Audio Setting

⑴Linear input and microphone input settable.

⑵When the audio input type is microphone input, the input volume and output volume are 80 and 95, respectively, and some models are 14 and 9.

⑶When the audio input type is linear input, the input volume and output volume are 10 and 95, respectively.

2.Video Setting

⑴Bit Rate

The rate of the first bit stream and the second bit stream of the device can be customized.

⑵Frame rate

Frame Rate of First and Second Bit Streams of Customizable Devices.

⑶Image quality

1-6 can be set, default is 1, the smaller the value, the better the image level, the larger the bit stream.

⑷Video format

50 Hz and 60 Hz settable.

Email Setting

Send e-mail to QQ e-mail as an example:

1. Smtp Server: smtp.qq.com

2.Server port: 465

3.Encrypt Type: SSL

4.User Name and Password Fill in QQ Account and Authorization Code

5.Send To: Mailbox for Receiving Alarm Pictures.

6..Sender : Sender’s mailbox address, here is QQmailbox, for example.

QQ mailbox address should be filled in; (same as user name).

7.Subjects and information can be filled in at will.

8.After filling in, click the application button, and finally click the test button.Check if you can send an alarm message.

Local Picture

1.Click on the icon and enter the local picture sub-ID of the picture playback interface to save the click Edit to delete the picture.

2.Select the image you want to delete and click the button.

Camera Setting

Manual Download

PDF Manual Download : CamHi Instructions for use – Camhi下载

Camera list display mode

Click the camera list interface icon  to select the camera list in large or small image mode.

Sidebar settings

Click the camera list interface button, or swipe the screen to the right in the camera list interface to enter the APP sidebar. The APP name is displayed on the sidebar. the below displays APP version.

• Local file

Click Local File to enter the local file interface. This interface displays all the local videos and pictures saved by this camera on this phone. Click on the file to playback the video file or view the local picture. Click the Edit button to delete the file.

• More

Click the More button to check whether the APP has obtained the notification permission of the mobile phone. If the display is not enabled, the APP cannot send the alarm push message. Clicking enabled, you can jump to the setting interface to open the notification permission.

Video/Image search and view

Local recording playback and download

Find the camera to be viewed in the camera list interface, click the icon, select the recording page, the recording file will be displayed, you can sort according to the size and length of the video file, click the button, you can save the video file to the mobile phone album. Click the edit button, it can delete the selected video file.

View local snapshot images

Click on the image page in the local file interface, the local snapshot images will be displayed, the images will be sorted according to the capture time, click the preview thumbnail to view the image, click the button, you can delete or save the image to the album.

Remote video playback and download

Remote video playback

Click the button “camera list interface” to enter the remote recording list interface. The APP searches for the last 6 hours of video files by default. You can customize the sorting according to the recording time, click the video file, and then click play to playback the video files in the SD card of the device.

Remote video download

Click on the video file in the recording list interface, and then click Download, the video file will be downloaded automatically. The downloaded video file will be saved in the local recording interface. After the video download is completed, you can click to continue downloading, continue to download other video files, or click view, will jump to the local recording interface automatically.

Remote video search

Click the button on the recording list interface, the search option appears, you can select the recording search range as needed.

Search time range is optional

Function settings

When the camera is online, click the camera list interface or the live interface icon to enter the camera parameter setting interface.

Basic settings

Wifi settings

Display the WIFI network connected to the current device

Click to get the wireless network around the device, the device will search for the WIFI network in the current environment automatically; select the password to configure the WIFI of the current device.

Change password

The access password of the camera can be modified. When ticking display password, the password will be visible.

Alarm settings  

Alarm management and notification

• Alarm push

Select On to indicate that a push message will be sent to the phone when alarming.

• Device alarm

1.Motion detection alarm

Select On to indicate that the device has enabled motion detection. Clicking adjust motion detection, it can draw motion detection area and adjust motion detection sensitivity (This function is suitable for some models.)

2.Sound alarm

Select On to indicate that the device with microphone function. When the surrounding sound is greater than the intensity of the device check sound, trigger an alarm, click to adjust the sound alarm, you can adjust the sound alarm sensitivity

Alarm Linkage

• Alarm capture to SD card

Select On to indicate that the alarm capture picture is saved to the SD card.

• Alarm recording to SD Card

Select On to indicate that the alarm recording file is saved to the SD card.

• When the alarm is triggered, the device issues a siren

Select on to indicate that when alarming the camera will sound an alarm. Siren type and the duration of the siren is optional

Email alarm linkage

Select On to indicate that the device will trigger the alarm and send a picture to the mailbox. Click Configure Email to set the mailbox information.

Send an email to the QQ mailbox as an example:

Smtp server: smtp.qq.com

Port: 465

Secure connection: SSL

Username: QQ number of the outbox

Password: Authorization code of the outbox QQ mailbox

Receiving address: the mailbox that receives the alarm picture

Sender address: sender email address, here is the QQ mailbox as an example, you need to fill in the QQ email address (consistent with the user name). Subjects and content can be filled in casually. After filling out, click the Apply button, then click the Test button to check if you can send an alarm email.

FTP alarm linkage

1.Alarm recording is saved to FTP

Select On to indicate that the alarm recording file is saved to FTP.

2.alarm capture saved to FTP

Select On to indicate that the alarm capture image is saved to FTP.

Click Configure FTP to set FTP information.

Server address: Fill in the erected FTP address

Port: Fill in the FTP port

Username and password: Fill in the username and password set in FTP

After filling in, click the Apply button, then click the Test button to check if you can send an alarm picture to FTP.

Picture capture number setting

You can set the number of alarm capture pictures, 1-3 sheets are optional

This function is suitable for some models.

Audio/Video management

Video settings

• Code rate

Can customize device’s code rate of first code stream and second code stream

• Frame rate

Can customize device’s frame rate of first code stream and second code stream

• Code level

1-6 can be set, the smaller the value, the better the image level, the larger the code stream

• Video system

50Hz and 60Hz optional

Audio settings

• Input volume

Adjust the input volume of the device

• Output volume

Adjust the output volume of the device

SD Card recording and capacity

SD Card plan recording

• Whether to enable recording

Select on, the device will save the recording to SD card

• Recording file time

Can adjust the length of each recording file manually.

• Recording time period

1.Simple settings

Select Simple settings, the recording time period defaults to Monday-Sunday full-day recording.

2.Advanced settings

Select advanced settings to customize the time period for each day of recording manually

Enter the advanced settings interface, click the quick edit button, select the time period to be recorded, you can customize the recording time period; edit it, clicking the Finish button to save the settings.

SD Card settings

Can view the total space and free space of the device SD card, can format SD card

System settings

Device time settings

1、Synchronize device time to phone time

2、The device time zone can be set. After the time zone is set successfully, the device will restart automatically.

Initial settings

• Restart the device

The camera will restart after clicking

• Restore factory settings

The camera will reset after clicking

Device information

Can get the device information of the camera: including device name, device type, Network type, number of user connections, software version, IP address, Subnet mask, gateway, DNS, etc.

Check for updates:

After clicking, the camera will check the firmware version automatically. If there is a new version, it will prompt for updates, click to upgrade online

(This function is suitable for some models)

Function description of live broadcast interface

Ordinary camera interface

The ordinary camera monitoring interface is displayed in the small screen mode by default. The function selection button is displayed at the bottom of the screen. More function keys can be called to slide to the left in the blank space. The function description of the buttons is shown in the figure below.

Note: Some functions require device support

PTZ function:

For devices with PTZ function, use your finger to swipe the live video, the camera will rotate according to the direction of the finger.

Exit the live interface:

Press the blank space and pull down on the small screen interface or click the back button to exit the live interface.

Panoramic camera interface

The panoramic camera will have different live broadcast interfaces depending on the model. It subjects to the connected model. The key function description as following:

Exit the live interface:

Press the back button to exit the live interface

View the camera

After adding the camera for a few seconds, wait for the camera to connect to the camera automatically, prompt the online description to view the camera video, click on the camera that displays online to enter the camera live interface.Camera status description:

Connecting: At this time, the camera is establishing a connection with the network camera. According to different networks, the connection time is different.

Online: This status indicates that the device is connected properly; click to view the video;

Not connected: This status indicates that the device is offline

Password error: This status indicates that the camera login password is wrong. Clicking on the camera in this state will pop up the Change Password dialog box.

Add camera

Install the APP, connect the mobile phone to the WIFI network, enter the APP and click the Add Device button to enter the Add Device interface. If it is the first time to use or restore the factory settings: the camera is not connected to the network, clicking the new device; the camera that has connected to the network, clicking on the device in use

New device add

After clicking the “New Device” button, power on the device, wait for about 30 seconds, confirm that the device is working, click next.

Connected to Network cable

If the device is connected to the network cable, click the “Connected Network Cable” button, the APP will search for the UID of the device in the current LAN automatically. Selecting the UID to be added and click the Add button, the device will search for the nearby WIFI signal automatically to enter the wireless configuration interface. Enter WIFI password, click “Configure wifi and add”, after WIFI configuration successfully, jump to the device list interface; if you do not want to configure WIFI temporarily, click the “Do not configure, directly add” button, adding camera fter confirmation.

Un-connected to Network cable

If the device is not connected to the network cable, click the “Un-Connected to Network Cable” button to enter the interface for selecting the network type.

Sound wave configuration network support equipment: PTZ Camera, Card type camera, Bulb camera, Small flying saucer camera, etc.

AP configuration network support equipment: Box camera, PTZ Camera, Speed dome camera, Big flying saucer camera, etc.

Sound wave configuration network

When the power is turned on, the device will enter the waiting state, and the device will send out a “beep” sound intermittently. Click Next to scan the QR code of the device UID number with the mobile phone. If there is no QR code, click Skip. Enter the password of the WIFI signal to be configured, click to start the sound wave configuration, the system will configuration WIFI automatically. After WIFI configuration successfully, there is a voice prompt

AP configuration network

When the network cable is not connected, turn on the power, click to add, the APP will search for hotspot signals of nearby cameras automatically. The hotspot format is IPCAM-XXXXXX, the password defaults to 01234567. Selecting the hotspot of the camera to be added, clicks connect. After connecting successfully, enter the device add interface, click Add, enter the wireless configuration interface, enter the router’s WIFI password, click “Configure wifi and add”, after WIFI configuration  successfully, jump to the device list interface; if you do not want to configure WIFI, click the button ” Don’t configure, add directly”, add camera after confirmation.

Note: AP configuration network needs to open the phone’s GPS function first.

Add device in use

Scan QR code

Generate a QR code by using the online QR code generation tool, and then scan the QR code through the mobile APP to scan and add.

Search for nearby devices

1、Click the button “Search for nearby devices” to search for the ip camera in the wireless network where the phone is located, and select the corresponding UID.

2、Enter the camera password (the camera default password is admin)

3、Click the button “Add” to add a camera.

Delete camera

In the device list interface, long press the camera to be deleted or click the button “setting” to enter the camera setting interface, click the button “delete device” to delete the added camera.

1. Setting motion detection

If you want to monitor a zone fixed, when the zone has exception, it enables alarm, you can choose motion detection function. Settings like below.

The equipment can support 4 zones setting, you can enable it through tick the option box at the bottom of page. When enable a zone, the zone box will display on the screen, and list zone number, moving mouse to this zone box, you can drag the box to any position; also can move mouse to red box at the bottom right corner, drag it to change the size. After setting, click apply, motion detection will take effect.

2. Setting alarm Linkage

When alarm triggered, the equipment will alarm with many ways, as shown in below picture:
send alarm and pictures to email
send captured pictures to assigned FTP server
send video recording to assigned FTP server
capture a picture, then save to TF Card
Recording a video for 15 seconds, then save to TF card (including 1-3 seconds warning before video)
linkage Preset: after the alarm, call preset
alarm capture quanity, setting as required (1-3 pieces)

If you want set Email alarm, please tick ”E-mail Alarm and Send with Picture”. and then click “Email setting”

3. Setting Email

The items in above picture is mandatory fields need to fill in. If the filled content is not qulified, the setting will not be successful. After writing completed, click Apply firstly, then testing, it will reminder testing successfully when finished.

Note:

1. The server of sending email should support POP3 protocol. In order to strengthen security and reduce spam, Many mail server closed this protocol at present. So users need to check if the server support POP3 before choose mail server, otherwise the mail can not send successfully.
2. For some mail server using SSL certificate, it must enable SSL option, then can send email successfully.
3. Some mailboxes require additional security settings, such as Gmail messages, you need to log in to your google account, open to allow less secure apps in “Sign-in & security” page.

If your Gmail mailbox opened “2-Step Verification”, then you need to set up a separate “app passwords” for camera login,

How to set up “app password” you can click on the “Learn more” to get help

If you do not know the security settings of other mailboxes, we recommended use Gmail.

4. Setting alarm time

The equipment will trigger alarm only after detected alarm in protection period. So you need to select which time to set protection carefully.

Note: When setting time, please adjust system time firstly.

How to set alarm to upload pictures and video to the FTP server

1. Setting motion detection

If you want to monitor a zone fixed, when the zone has exception, it enables alarm, you can choose motion detection function.

Settings like below. The equipment can support 4 zones setting, you can enable it through tick the option box at the bottom of page.

When enable a zone, the zone box will display on the screen, and list zone number, moving mouse to this zone box, you can drag the box to any position; also can move mouse to red box at the bottom right corner, drag it to change the size.

After setting, click apply, motion detection will take effect.

2. Setting alarm Linkage

When alarm triggered, the equipment will alarm with many ways, as shown in below picture:

send alarm and pictures to email

send captured pictures to assigned FTP server

send video recording to assigned FTP server

capture a picture, then save to TF Card

Recording a video for 15 seconds, then save to TF card (including 1-3 seconds warning before video)

linkage Preset: after the alarm, call preset

alarm capture quanity, setting as required (1-3 pieces)

If you want set alarm to upload pictures and video to the FTP server, please tick ”Save Picture on the FTP Server” and ”Save Video on the FTP Server”. and then click “Email setting”

3. Setting FTP Server

Note: If using FTP function, you need to apply the user name and password from FTP Server firstly, and apply a certain storage space at the same time, also asking the user have anthority to write and build sub-directory to storage space.

4. Setting alarm time

The equipment will trigger alarm only after detected alarm in protection period. So you need to select which time to set protection carefully.

Note: When setting time, please adjust system time firstly.

Timing capture and timing record of SD card

1.Timing capture

Choosing “save image to SD Card” or “save images to FTP server”, at a regular interval (can be set like above picture), the device will capture images saving to SD Card.

Click “FTP” into set FTP

Note: If using FTP function, you need to apply the user name and password from FTP Server firstly, and apply a certain storage space at the same time, also asking the user have anthority to write and build sub-directory to storage space.

2. Timing record

Video file duration: can set video file duration, default is 600 seconds.

Open video: can choose whether open video to TF Card

Stream: can set recording stream

recording time: set timing recording time as required

then confirm the camera support SD card and insert SD card, as shown in below picture:

How to view pictures card and download video of SD

Click “SD card” button in IE home page of camera.

Page will display the date of picture and video, select date.

Images folder to store pictures, record folder store videos.

Open images folder, click the images file name directly view picture.

Open record folder, click the record file name to download video.

CAMHI IP Camera Port mapping setting method

1. Please setup the IP address to be Static IP address.

2.Please modify HTTP port number.

The device HTTP port mapping to the external network router,
“External ports”: This port is corresponding to the access requirement of outside network
“Internal Port”: port for this equipment
“Service agreement” selects “ALL”
“IP address”: LAN IP address of the camera.

NOTE:
If your router supports UPNP function, you can also use UPNP port mapping automatically.
UPNP stands for universal plug and play, if you started UPNP, once the IP camera was connected into the LAN, it will communicate with the router of the LAN.
It will request the router to open a port to forward its own port. User doesn’t need to log in the router to set the port forwarding.

users in the use of the function, need to confirm a router also is enabled UPNP; Because many router model, not necessarily can very good support UPNP, testing and supporting the router is very good with, or suggest not start the function. At present test and TP-LINK router cooperate good.

<p>The post CamHi Pro Tutorial Guide first appeared on NVR IPCAMERA SECURITY.</p>

Nooie Cam 360 Gives You Security With a Twist

Nooie Cam 360 features automatic motion tracking that keeps up with the action. It can also be controlled manually using the Pan & Tilt feature in the Nooie App.

Features

• Stylish, Intuitive, Easy Setup: Nooie Cam 360 is easy to install, simple to control, and a breeze to maintain. Compatible with 2.4GHz WiFi network. Download the Nooie App from App Store or Google Play. Works with Alexa.
• 1080P HD + Superior Night Vision: 1080P HD camera lens with two 940nm infrared LEDs. Night vision up to 32ft (10m) in pitch-black. Optional status light.
• 360° Motion Tracking: Equipped with a 101° field-of-view camera that can rotate 355° horizontally and 94° vertically. When motion tracking is turned on, it can automatically sense and track the action in your home in full 360°.
• Pan, Tilt, and Zoom: Control the camera angle manually to pan, tilt or zoom with the Nooie App.
• 24/7 Live Stream and History Playback: Watch live stream video or replay recorded events anywhere and anytime (microSD card or Nooie Cloud storage is required to access Nooie Playback).
• Two-Way Audio: Listen and speak with the built-in microphone and speaker.
• Motion & Sound Detection: Receive instant customizable app notifications wherever you are, whenever motion or sound is detected.
• MicroSD Card or Nooie Cloud Storage: Store your video locally, or externally in the cloud — your choice.

In the Box

Product Overview

Read Next : V380 IP Camera Installation Manual

Nooie Cam 360 LED Indicator Guide

 

How To Turn ON/OFF the LED Indicator light

1. In the Nooie App, tap Cam in the bottom navigation bar, then choose your device.
2. Tap the Settings icon on the top right corner.

   

3. Tap General > LED Indicator to turn it ON or OFF.

How to setup a 360 camera in the app?

Before Setting up the 360 camera

Make sure you are logged into your account in the Nooie app. If you have not or are having an issue creating an account please refer to the following link. https://help.nooie.com/hc/en-us/articles/4419763097751-How-to-create-an-account-in-the-Nooie-app-. Connect your phone to a password-protected WiFi network. A cellular network is not supported for setup.

Setting up the 360 camera

1. Plug the camera into an electrical socket for power. The recommended maximum distance from the “360” camera to the WiFi router is 40 ft (line of sight)
2. Next, press the (+) symbol in the top right of the Nooie app. Select “Add Camera”.

            

3. Under “Add Device”, select the “Nooie Cam 360” picture.

4. Under “Add a Camera”, make sure the camera displays a flashing “red light”. If you don’t see a flashing red light, press the “reset button” on the camera for 15 seconds or until an audible sound is heard. Click “Red Light On”.

5. Under “Connect to WiFi”, make sure the “Current Network” displayed is correct. Only 2.4GHz WiFi is supported. Enter the correct WiFi “Password”. Click “Next”.

6. Under “Connect to Camera”, place the “QR code” displayed on the phone screen 8″ to 10″ from the camera lens. An audible sound will occur from the camera and the blinking “red light” will change to a blinking “white light”. Click “Next”.

7. Under Pairing…Please Wait, the camera will go through a pairing process until an audible sound occurs from the camera. The blinking “white light” will change to a solid “white light” when the camera is connected.

8. Once connected, create a location “name” for the “Indoor” camera. Click “Save” to complete the setup.

How to install the 360 cam on a wall?

Installation

Required Tools

• Electric Drill

Tips

1. If you choose to mount your camera to a wall, use the Nooie App to check the camera view before mounting.
2. Metal objects may interfere with the signal; select a location away from metal.
3. Choose a location away from direct sunlight for the best video quality.

Mounting the camera

1. Drill holes and screw in the wall mount plate.
2. Attach the bottom of the camera to the wall mount plate and slide it into the hook.

Nooie Cam 360 Motion Tracking

 

Motion Tracking detects and tracks horizontal movement automatically within the camera’s field of view.

• When the camera detects motion, it will turn to follow motion to keep it within the field of view The camera will remain in that position until motion is sensed again, or the camera is moved manually via the Nooie App. 
• Motion Tracking can be turned ON and OFF independently of Motion Detection.

Read Next : How to Trigger the Linkage Between Ipc of TP-Link Kasa Via IFTTT?

How to Locate the Motion Tracking Feature

1. In the Nooie App, tap on Camera in the bottom navigation bar, and choose Nooie Cam 360.
2. Tap the Settings icon on the top right corner.

   

3. Tap on the Motion Tracking toggle to turn it ON or OFF.
   • The motion Tracking toggle will be blue when it is ON and will be gray when it is OFF.

Nooie Cam 360 Motion & Sound Detection

 

Tip! You can set a schedule a timeframe for when you want to receive alerts for motion or sound detection (e.g. from 8 AM to 6 PM or whenever you are away from your home.) to optimize the use of video storage space if you’re using a MicroSD card.

 

Accessing Alerts

1. In the Nooie App, tap on Camera in the bottom navigation bar, and choose Nooie Cam 360.
2. Tap the Settings icon on the top right corner.

   

3. Tap on Detection > Motion Detection or Sound Detection to turn on the feature and create schedules.
   

   

4. Sensitivity: Adjust the sensitivity of motion/sound detection to receive more or fewer alerts. The more sensitive the setting, the more alerts you are likely to receive.

How to solve your 360 Cam’s connectivity issue?

If your Nooie camera failed to connect, please check the LED indicator on your camera and reference the following recommended solutions.

There are 4 common situations for why your Nooie camera may not be operating:

1. Camera is not connected to the server.
2. Camera is not connected to the router.
3. Incorrect WiFi password is being used.
4. Camera has a malfunction, not operable.

Situation #1

LED color: White (flashing fast and never turns to steady white light)

Reason: Camera is not connected to the server.

Solution:

1. Check your router and see if there’s any limits or firewall.
2. Turn off the firewall and connect again.

*If the problem persists, please email to support@nooie.com for further assistance

 

Situation #2

LED color: White (flashing slowly)

Reason: Camera is not connected to the router.

Solution:

Step 1 – Begin by Reviewing These Requirements.

1. Camera is connected to 2.4G Wifi; does not require authentication.
2. WiFi account/password does not contain special characters.
3. No wall between the camera and router.
4. Router is connected to less than 10 devices.

Step 2 – Check Your Router Settings

1. If you have smart Wifi, turn it off and try connecting the camera again.
2. If your router is dual band (5G & 2.4G), temporarily turn off 5G until the camera is connected.
3. Encryption & Authentication methods should be set to WPA2-PSK and AES.
4. Try turning off the wireless MAC address filter.
5. Make sure the DHCP server is on.

*If the problem persists, please email to support@nooie.com for further assistance. Provide the QR code located at the bottom of your camera, and the Wifi pairing code.

 

Situation #3

LED color: Red and white (flashing)

Reason: Incorrect WiFi password is being used.

Solution:

1. Re-eneter your WiFi password and make sure it’s correct.
2. Try using an alternative hotspot such as a smartphone to make sure the problem is related to the hardware and not your WiFi network.

*If the problem persists, please email to support@nooie.com for further assistance.

 

Situation #4

LED color: Red and white (flashing)

Reason: Camera has a malfunction, not operable.

1. If all situation solutions did not work, the camera may have a malfunction.
2. The camera not be operable due to manufacturing issue.

Solution:

Please email support@nooie.com and describe the situation, and we will further assist.

Nooie Cam 360 Cam won’t pan or tilt

Problem

Pan and tilt functions are not working in the Nooie App.

 

Tips to Resolve

If the Nooie Cam 360 does not respond to pan and tilt gestures in the Nooie App, you may need to update the Nooie App to the latest version.

1. Download the latest version of the Nooie App(as shown below).  Confirm that it is the Nooie App, not the Nooie Cam App that will be retired in the near future.

If the problem persist after updating to the newest Nooie App version, please contact support@nooie.com and we will be happy to assist you right away.

 

Download Nooie App Now

Android

iOS

What is the visual range of the Nooie Cam 360 at night?

360 Cam has two 940nm infrared lights, and allows visibility up to 32 feet at night.

How can I rotate the video image?

To rotate the video image:

1. In the Nooie App, tap Cam, then your device ****item.
2. Tap the Settings icon on the top right.

   

3. Tap General > Audio / Video > Rotate

How do I reset the Nooie Cam 360?

You can reset the Nooie Cam 360 in two ways.

To reset the Nooie Cam 360 through the Nooie App: 

1. Open the Nooie App, tap Cam, then your device ****item.
2. Tap the Settings icon on the top right.

   

3. Scroll down to the bottom of the Settings screen to Reset to Factory Setting.

To manually reset the Nooie Cam 360:

1. Find a pin or an object with small tip such as a paperclip.
2. Use the pin to poke the reset button (located next to the USB port), and hold for 5 seconds.
   • You will hear a beep or “ding-dong” sound when the Nooie Cam 360 is reset.

<p>The post Nooie 360 Cam full setup guide first appeared on NVR IPCAMERA SECURITY.</p>

Method 1: Use the RESET button

Type 1: For Security Camera

While the camera is powered on, press and hold the Reset button for at least 5 seconds until the LED blinks red. The camera will reset and reboot.

Type 2: For Pan&Tilt Security Camera

While the camera is powered on, tilt the camera lens up, then press and hold the RESET button for at least 5 seconds until the LED blinks red. The camera will reset and reboot.

Type 3: For Outdoor Security Camera

1. Loosen the screws on the back panel and remove the cover.

2. Press and hold the Reset button for at least 5 seconds until the LED blinks red.  

Method 2: Remove the camera via the Tapo app

Option 1: Go to the Home page

On the home page, long tap on your camera model card. Then tap Remove at the bottom to remove the camera. The camera will be removed from your TP-Link account and reset to the default settings.

Option 2: Go to Camera Settings page

1. On the home page, tap on your camera model card or tap Camera Preview > Manage to go to Live View page.

2. On the Live View page, tap the gear icon to enter the Camera Settings page.

3. Tap Remove Camera at the bottom to remove the camera from your TP-Link account. The camera will be removed from your account and reset to the default settings.

If you cannot reset your camera successfully, please try the following steps：

1. Make sure your camera can be powered on.
2. Please do not operate after power-on, wait 10 minutes and try to reset again.

If the issue is still the same, please contact TP-Link technical support.

Get to know more details of each function and configuration please go to Download Center to download the manual of your product.

<p>The post How to reset my Tapo camera – Video Guide first appeared on NVR IPCAMERA SECURITY.</p>

1. Download “Annke Nova“, register an account, log in to the APP, and then add an IP camera to the APP. Here is the net link instruction of how to add the camera to the Annke Nova app for your reference.
   https://help.annke.com/hc/en-us/articles/360000253461

   

2. Download and install the “IFTTT” APP, then you can use your Google account, Facebook account, or register a new account for login.
   
3. Search “EZVIZ ” on IFTTT, select the EZVIZ module then login with your account. You should authorize IFTTT to access your EZVIZ account, and tap “Open” to enter the IFTTT.
   
   
4. Search “TP-Link Kasa” on IFTTT,  select the TP-Link Kasa module then log in with your TP-Link Kasa account. You should authorize IFTTT to access your TP-Link Kasa account, and tap “Open” to enter IFTTT.
   
5. IPC of Nova Series triggers TP-Link Kasa by motion detection.

   a). Link with IP Camera
   Open the “My Applets” and tap the “+” icon on the top right corner on the EZVIZ main page, then tap “+this” to search and enter EZVIZ to select the trigger. Click “An alarm event occurred” and then select the device and the alarm type. Choose “Nova S” and “Motion Detection Alarm”, then complete the settings by tapping the top right corner “√“.
   
   
   

   b). Link with TP-Link Kasa
   Choose “+that“,  then search and open “TP-Link Kasa“, select “Turn on” to connect Kasa. In the login page, then authorize to bridge IFTTT and Kasa. Enable the notification then you can tap “Finish” to complete the settings.
   
   

<p>The post How to Trigger the Linkage Between Ipc of TP-Link Kasa Via IFTTT? first appeared on NVR IPCAMERA SECURITY.</p>

Method 1: Via VIGI Security Manager

Step 1. Click the Forget Password option.

If the camera is not added, go to Settings > Device > Device List > Discovered Devices, select the device and click the Set Password or + Add > Forget Password.

If the camera has been added, go to Settings > Device > Device List > My Devices > Settings icon of the camera > Basic Information > Device Security > Modify > Forget Password.

Step 2. Send the Verification Code to your Reset Password Email.

If the camera is connected to the internet, click the Send Code and you’ll receive a verification code sent to your Reset Password Email.

If the camera is not connected to the internet, please Download VIGI App in the App Store or Google Play. Scan the QR code with the app and you’ll receive a verification code sent to your Reset Password Email.

Step 3. Enter the verification code and click Next.

Step 4. Enter the new password.

Method 2: Via VIGI NVR

Step 1. Click the Forget Password option.

Right click to open Main Menu, go to Settings > Camera > Device Access > Add Device > Discovered Devices and you will see Forget Password option. If the camera has been added and is not certified, you need to remove the camera first.

Step 2. Send Verification Code to your Reset Password Email.

• If the camera is connected to internet, click the Send Code and you’ll receive a verification code sent to your Reset Password Email.
• If the camera is not connected to internet, please Download VIGI App in App Store or Google Play. Scan the QR code with the app and you’ll receive a verification code sent to your Reset Password Email.

Step 3. Enter the verification code and click Verify.

Step 4. Enter the new password.

Note:

1. What’s the Reset Password Email?

When you first activate camera, it is asked to enter your Reset Password Email. It is only used to receive the verification code when you need to reset the password.

2. What should I do if I don’t receive the verification code?

• Check your junk or spam folder.
• Add noreply@tp-link.com in White list (by clicking Create a new filter) in your email setting.
• Check your email filter setting in your email account.

If the above steps don’t solve your problem, it’s suggested to contact TP-Link support.

<p>The post How to reset the password of the VIGI camera? first appeared on NVR IPCAMERA SECURITY.</p>

Introduction
When you are away home, there are always something you care about. This is where the smart camera functions. No matter your child is climbing
the kitchen cabinet, or the pet is stealing snacks, the Pan/Tilt Home Security Wi-Fi Camera helps you stay with them anytime, anywhere. Receive a
notification whenever your camera detects motion and see a video clip of this motion to check everything.
• Smooth Pan and Tilt – 360° horizontal range and 114° vertical range.
• 1080p High -Definition – Capture every detail in crystal-clear Full HD definition.
• Advanced Night View – Even at night, the camera can provide a visual distance of up to 30 ft.
• Live View – Always stay with that matters most to you from anywhere, anytime.
• Two-Way Audio – Communicate with others with the built-in microphone and speaker.
• Sound and Light Alarm – Trigger light and sound effects to frighten away unwanted visitors.
• Privacy Mode – Shut down the surveillance to protect your privacy.
• Sharing – Share the memorable moments with your family and friends.
• Safe Storage – Store up to 128 GB on a microSD card*, equal to 384 hours (16 days) of footage△
.
*The SD card is not included in the package.

<p>The post Tapo Home Security Wi-Fi Camera Setup Guide first appeared on NVR IPCAMERA SECURITY.</p>

How to set up cloud camera with tpCamera APP?

This article is only suitable for basic configurations.

Note: NC Class Cameras work with tpCamera app only.

Run the tpCamera APP on the Android phone or Iphone

Note: tpCamera APP can only be used in iOS 9.0 or higher/Android 4.4 or higher.

For IOS devices: download the tpCamera APP in APP store

For Android phone: Scan the QR code below or on the camera’s package and an APP downloading link will come up.

Here we take Android as an example to set up the camera:

1) Connect your camera to your router by an Ethernet cable, then connect the phone to the Wi-Fi network of same router.

Note:

1.The NC210 do not have Ethernet port, it can only be configured via Wi-Fi.

2.After we configured the camera successfully, if you don’t want the camera connect to the router via Ethernet cable, you can disconnect the Ethernet cable between the router and the camera, and the Camera will connected to the router automatically by Wi-Fi.

2) Log in the tpCamera app with your cloud account, choose “+” to add a new device.

3）You need to choose the model number of your camera before adding it.Tap “More” you could find more models.

4) tpCamera APP will detect your camera in LAN. Tap “Ethernet (Wired)” when select connection type.

Note: Please make sure that your camera’s LED turns solid green.

5）Here it will ask you to set a password for secure access to your camera.

6) Choose your own router’s Wi-Fi network and input the password.

7）It will remind you to Set Location of your camera.

Now you can view your camera on APP.

<p>The post How to set up cloud camera TP-Link first appeared on NVR IPCAMERA SECURITY.</p>

A firmware update can resolve issues that the previous firmware version may have and improve its current performance.

To Upgrade

IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process

• Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
• Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）
  How to find the hardware version on a TP-Link device?
• Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
• To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
• It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
• Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.

Download for VIGI NVR1008H V1

Download for VIGI NVR1016H V1

VIGI Security Manager

Setup Video

• How to Manage VIGI Cameras and NVRs Using VIGI Security Manager

  This video demonstrates how to manage VIGI cameras and NVRs using VIGI Security Manager in two scenarios: • using VIGI Security Manager in your local network • using VIGI Security Manager remotely THIS VIDEO APPLIES TO: All VIGI Cameras and NVRs

• How to Manage VIGI Cameras via VIGI NVR

  This video demonstrates how to manage VIGI cameras via VIGI NVR. It consists of three steps: • Connect the hardware. • Set up VIGI NVR and add VIGI cameras. • Bind VIGI NVR to TP-Link ID for remote management. THIS VIDEO APPLIES TO: • All VIGI Products

• How to Manage VIGI Cameras and NVRs via VIGI App

  This video demonstrates how to manage VIGI cameras and NVRs via the VIGI app. It consists of three steps: • Launch the VIGI app. • Add devices using the VIGI app. • View the recordings and configure the settings. • Enable alerts to get instant alerts This video applies to: • All VIGI VIGI Cameras and NVRs

<p>The post VIGI NVR Firmware Tools DL first appeared on NVR IPCAMERA SECURITY.</p>

Step 1. Right click on the Live View screen, go to Settings > System > User Management, select the admin account and click .

Step 2. Tick the Change Password, enter your old password and new password, click Save. You can also change the Password Reset Email for NVR, Preset Password for Camera and Password Reset Email for Camera here. Done.

Note: If you forget the old password, please refer to the link to reset the password.

To get to know more details of each function and configuration please go to Download Center to download the manual of your product.

<p>The post How to Reset Password VIGI NVR? first appeared on NVR IPCAMERA SECURITY.</p>

Step 1. Right-click on the screen, click Settings on the Main Menu.

Step 2. Go to Settings -> System -> Firmware Upgrade.

Method 1: Upgrade firmware online

1. Click Check for Update.

2. Click Upgrade, and the NVR will be automatically upgraded.

Method 2: Upgrade firmware locally

1. Please find your NVR at TP-Link Download Center, download the latest firmware of your NVR and save the file of firmware to your USB drive. Insert your USB drive into the USB port on the front panel of the NVR.
2. Click Select upgrade firmware and select the firmware you need for the upgrade.

3. After the import of firmware, the NVR will be automatically upgraded.

<p>The post How to upgrade the firmware of VIGI NVR? first appeared on NVR IPCAMERA SECURITY.</p>