ENS Emerald ip camera installation guide

M.Salih ASLAN — Mon, 26 Dec 2022 06:14:35 +0000

ENS Emerald ip camera installation guide This guide will use EM-IPCP8D3-F28-LH-AI as an example of a IPC that has a physical reset button. IPCs with a reset button will be listed at the bottom as well as a video demonstration.

Emerald IP Camera Reset via Button

This guide will use EM-IPCP8D3-F28-LH-AI as an example of a IPC that has a physical reset button. IPCs with a reset button will be listed at the bottom as well as a video demonstration.

Step 1.
Verify that the device is powered up. One of the ways you can do this is by using ENS Tools to see if the IPC is online.

Step 2.
Locate the cover on the IPC body and remove any screws that may be holding it down.

Step 3.
Hold down the reset button for about 10 – 15 seconds.
The IPC will reboot and the reset will be complete.

Models WITH reset buttons.
EM-IPCE2B100-X10-LH-AI
EM-IPCE4B150-X22-LH-AI
EM-IPCP4B3-F40-FC-AI
EM-IPCP4B4-F28-AD-AI
EM-IPCP4B4-F28-M-LH-AI
EM-IPCP4B5-MZ-LH-AI

EM-IPCP4D4-MZ-M-LH-AI
EM-IPCP4T3-F28-FC-AI
EM-IPCP5FE1-F14
EM-IPCP8B3-F28-AD-AI
EM-IPCP8B3-F40-FC-AI
EM-PTZE26500-X33-LH
EM-PTZE28250-X45-LH
EM-PTZE48250-X40-LH
EM-PTZP26150-X25-LH
EM-PTZP46150-X33-LH
EM-PTZP5750-X4-AD

EM-PTZV26150-X25-LH
EM-PTZV44100-X25-LH
EM-PTZV4530-X5-IN

ENS Emerald ip camera installation guide

Add Emerald IPC to Titanium NVR

Answer

Emerald IPC cameras come with ONVIF enabled by default.

1- Identify the camera on the network using ENSTools, login and configure a static IP address.

2-Login on the 3rt party brand in this case is a Titanium NVR, add camera and use the manual option, set IP camera address that we previously configured, Port HTTP 80, same password that was used during camera activation. Then select protocol ONVIF and add.

3- Once the camera is added it will display as Online.

How to playback video from IP Camera that has SD-Card Installed

Answer

Log into the camera from the web interface

Go to the playback option and from there you will have access to the recordings right on the camera. On the right side you see a calendar, that is for you to filter out certain dates you would like to view

Recording is filtered by dates on the right hand side, you can scrub to certain time frames on the bottom. You can also download the video right on to your computer for archival purposes.

Here are the various options for playback. They are color coded for ease of viewing

RED- Select dates on which you want to playback

GREEN- from left to right the options are as follows, change view layout(single camera view to 16), clear all channels, and on the right is snapshot all cameras selected

BLUE- Here you can play, pause, reverse and fast forward

PEACH- Here you can control the scrub speed

PINK- Here you can scrub through the time of the current day selected

How to Configure Image Settings of IP Camera

Answer

After logging in, under setup on the left hand side, there should be a video tab, and go to video once more to access video settings. In the next few screenshots you will see the different settings

1.1. Here are the image enhancement settings, if the image isn’t coming out to your liking, adjusting these filters will help

1.2. Here are the exposure settings

1.3. Smart illumination

1.4 White balance

1.5 advanced settings

Alternatively, right after logging in, on the top right there’s a box with the word image on it, you can click it and it’ll navigate you straight to the picture above

Here we have the OSD (On Screen Display) settings, here you can add a number of different types of information that would be relevant to any job specifications.

Here we have a privacy mask setting. This function allows you to censor a certain area of a camera image. Could be useful to provide security where cameras are in sensitive areas.

How to locate IP Camera on LAN via ENS Station

Answer

Open ENS Station and navigate to device management

Here you can see the IP cameras by IP address. You can locate your specific camera by ip address, model number or Serial number. The cameras you see already are on the network so you can quickly add them

Manually adding the camera via IP. enter the IP address of the camera and make sure the username and password match up to that specific camera or recorder you want to add

After you added the camera it should say online and then go to live view and you will be able to get the image up like we have pictured below

How to reset IP camera

Answer

1. Log onto the remote web interface

2. Under the setup menu, on the left hand side go all the way down to the System tab

3. Under the system tab, go to the maintenance option and you will see config management, the default option factory defaults the current camera connected. Make sure the box next to Default is checked because if not then your network settings and password will not factory reset.

How to Set IP Camera to Static

Answer

1. After logging in go under setup, go to network settings on the left hand side, then click on network once more

2. The option where it says obtain IP address you’re going to want to click on that option and a drop-down menu appears, from there you can select Static

3. Once static is selected you can set an IP address manually and other related configurations

How to locate device on LAN via ENS tool

Answer

How to locate IP Camera on LAN via ENS Station

1.Connect camera to POE switch

2.Open ENSTools and camera should take a few moments to pop up (Highlighted below)

3. Under the configuration tab click on the E symbol corresponding to the camera and log in with the username admin and password 123456, it will ask you to create a new password.

How to configure Snapshot

Answer

Log onto the web interface

To configure a snapshot, under setup go to events on the left hand side and the camera image should come up. Detection mode is set to area on this camera so that means whatever comes into that specific area the camera will take a snapshot of it

To send the picture to the camera SD card under trigger actions on that same page on the right the image edge storage box is ticked off and that simply sends it all to the SD card. You can set it to send to an email to save space on the SD card as well.

How to view snapshots from IP Camera

Answer

Log into the web interface

Under the photo option on the top of the page it will take you to where the snapshots are stored on the camera. In this screenshot the camera was set to take snapshots whenever motion is detected. Navigate to the proper file and your snapshot should appear. Cameras will be identified by their IP address

To configure a snapshot, under setup go to events on the left hand side and the camera image should come up. Detection mode is set to area on this camera so that means whatever comes into that specific area the camera will take a snapshot of it

To send the picture to the camera SD card under trigger actions on that same page on the right the image edge storage box is ticked off and that simply sends it all to the SD card. You can set it to send to an email to save space on the SD card as well.

How to configure IP Camera to record to SD-Card

Answer

Log onto the web interface for the camera

Under setup go to storage on the left-hand side of the page

Storage medium should be the SD card you’ve placed into the camera and make sure to format it to be able to use it.

Allocate capacity is used for when you would want to set how much storage you want for video and how much you would like for pictures

Storage policy has 3 options, the first which is manual and alarm recording and that means you would manually need to press record and scheduled records automatically within that scheduled range, all 3 settings have alarm recording so it will record in case any alarm have been tripped.

Plan is your recorder schedule, if you have it on 24/7 like shown in the picture above thats continuous recording, you can set it to record whatever time you like.

How to Set Date and Time on an IP Camera

Answer

1. After you have logged into the remote web interface for the camera, on the banner options go to setup on the left-hand side there should be date and time options available for configurations.

2. Expanding further you can see 2 options for time, TIME and DST (Daylight Savings Time) , you can sync with a NTP server (Network Time Protocol) or sync with the computer time.

2.1. Here you can see the settings for configuring the time with the NTP server (Time.windows.com)

2.2 Here you can see the settings for configuring time with the system (For offline systems)

2.3. DST options

Change IPC from Line to Mic

Answer

Change IPC from line to mic

* Note camera needs to have 2-way functionality. You may also use the Access button while on the same network as the recorder. If not, you must use the IP address of the IP camera.

1. Type IP address for camera on URL.

2. Enter username and password.

3. Click the Configuration Tab on top once you are logged in.

4. Click Video/audio on left side panel

5. Go to the Audio tab on the top sub panel.

6. Once you are in the Audio tab. You are able to select between MicIn/LineIn on the Audio Input option.

The post ENS Emerald ip camera installation guide first appeared on NVR IPCAMERA SECURITY.

Titanium Recorder Password Reset Guide

M.Salih ASLAN — Wed, 24 Aug 2022 19:24:24 +0000

Answer

***Make sure that the system is logged out before trying to do a password reset***

Click on the icon on the lower left hand corner of the screen. Select “Login”

You may answer your security question to unlock the device.
Otherwise, Click on “Dynamic Password”

Please have a person at the recorder provide all the information within the Dynamic Password page. Every piece of information has to be identical (Capital letters for MAC address, colons, spaces, etc.) Once this information is provided to a technician, they will provide a code to enter on the last line. The code provided from the technician is a mix of numbers and all capital letters.

After entering this information, the system will prompt that the password recovery was successful and default the admin password to “123456” or allow you to enter a new one.

Password Resetting, defaulting a TVT IPC using IP Tool

Answer

Open up the IP tool, make sure that the computer is connected to the same network as the camera.

Select the camera and find the MAC address. Enter the MAC address in the password reset area. After entering it and clicking OK, you will have 30 seconds to power down that camera. Once power cycled, the camera will be back to default settings.

The post Titanium Recorder Password Reset Guide first appeared on NVR IPCAMERA SECURITY.

ENS Security Firmware Software Tools Download

M.Salih ASLAN — Sat, 08 May 2021 06:48:12 +0000

ENS is committed to offering technology that helps our communities live in a healthier and safer environment. Every solution exceeds the strictest Video Surveillance industry standards, offering high-quality, state-of-the-art solutions with best-in-class support by making your success our success.