Intro

You’re Not Alone

Installation can be hard. We’re happy to talk it over with you or take over a DIY project that you’ve realized needs professional installation. Our support hours are from 9AM-7PM Monday – Friday (EST) and we are available via chat, email, phones, and remote PC screen-sharing, if you need any help. You can reach us at 866-414-2553.

Disclaimer: The laws governing cable and wire installation can vary from state to state and sometimes even counties and cities pass specific, unique laws regarding cabling; these state, county and city laws are too complex for us to explain. This page is not a how-to installation guide, as we cannot keep up with local laws.

Although we now offer installation, locally, we started as a DIY-only company, and we primarily serve those adventurous types who want to run the cable for themselves. Even so, we get asked about do-it-yourself installation all the time…. We wanted to post a few of our standard answers here.

Part 1

Don’t Start a Fire or Shock Yourself

Electricity Can Kill You; Avoid Electrical Lines!

Never strap, staple or otherwise run networking cable to conduit or raceways carrying electrical current. Never run any cable within 2 inches of Class I electrical lines, lighting, fire alarm, or power lines or devices.

Give a Wide Berth to High Voltage Devices or Lines

Never run any cable within 6 feet of a conductor or fuse box. A minimum 5-inch distance is required from any fluorescent lighting fixture or power line over 2 kVA and up to 24 inches from any power line over 5 kVA. If unsure about the a device or line, consult an electrician. Route cable away as far as you can from large motors, generators, induction heaters, arc welders, x-ray equipment, and radio frequency, microwave or radar sources. NEC/NFPA 70, Article 800-52

Protect it from Future Physical Damage

You might want to put a nail or screw in later and don’t want to puncture your cables, so when a cable, raceway, or soft conduit (anything you can puncture) is installed parallel to framing members (joists, rafters, or studs), furring strips, or crown molding, keep the cable at least 32 mm (1.26 inches) from the edge. NEC 300.4(D)

Don’t Leave it Dangling – Secure Your Cables

You can connect cable directly to a surface with straps, staples, cable ties, hangers, or similar fittings, but you have to secure it somehow. NEC 800.24; 300.11

Use Plenum rated cable in Areas with Airflow

If you are going to run cables through an area which is used by your heating, air circulation, or air conditioner systems (such as above a drop ceiling in an office), you must use Plenum rated cables, which have a special insulation that has low smoke and low flame characteristics. When securing cable in Plenum required areas, make sure your straps, cable ties, and similar fittings also are plenum rated. NEC 830; NFPA 90A

National Rules – Consult your local laws

These guides are meant to familiarize our clients with the national requirements as expressed in the National Fire and Alarm Signaling Code and the National Electrical Code. Your state or local laws may differ. If you live outside the USA, consult your governmental laws. Don’t consider this your only resource.

Turn the Breaker Power OFF

Any time that you will be drilling or cutting into your wall, you want to turn the power off. You don’t want to drill into a hidden electrical line. You probably already know this, but our lawyers insisted.

Wear Safety Goggles

Any time that you are drilling, you want to wear safety goggles and hearing protection, like ear plugs.

Security Camera Installation Guides v2

Part 2

Drilling through Different Materials

Sheetrock (most interior walls)

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of sheetrock.

Wood

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of wood.

Stucco

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of stucco.

Brick and Masonry

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of brick.

Concrete

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of concrete.

Metal Siding

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of metal siding

Part 3

Running the Cable

Basic Cabling

Terminating Cable (Putting the ends on)

Instructions for putting the RJ45 ends on to ethernet (for example, Cat5 / Cat6 / Cat5e) cable.

Using Our Waterproof Connectors

When installing a camera outdoors, it is imperative that you put our waterproof RJ45 Connector on the ethernet (for example, Cat5 / Cat6 / Cat5e) cable.

No Protection – Just Running the Wire

You can connect cable directly to a surface with straps, staples, cable ties, hangers, or similar fittings, but the cable could get damaged and someone might be able to cut it.

24 Volt Wiring: PTZ

The Spotlight PTZ cameras uses 24 volt power rather than POE because it requires more power than is capable of Power-Over-Ethernet for its natural white light spotlight. The Laser can also be powered via 24 volt power and can be powered the same way, although it is not required to do so. This guide shows you how to wire these PTZs.

24 Volt Wiring: Sharpshooter

The Sharpshooter IP Bullet cameras uses 24 volt power rather than POE because it requires more power than is capable of Power-Over-Ethernet for its long range infrared. This guide shows you how to wire the Sharpshooter.

Protecting your Cabling

Liquidtight Plastic Tubing

Liquidtight plastic tubing is easier to work with than flexible metal tubing, but is less secure. It is also great for areas with lots of expected moisture as it won’t rust.

Flexible Metal Conduit (FMC)

Flexible metal conduit is difficult to cut (watch out for sharp edges), but easier than solid conduit to install.

Electric Metal Tubing (EMT)

Solid metal conduit is the most secure form of installation. It requires a specialty conduit bending tool.

Conduit Fill

This chart will let you know how many cable runs you can fit in one conduit pipe, depending on the size of the conduit.

Raceway (Outdoors) – Coming Soon

Raceways are most popular indoors to make the space look clean and professional. There are also outdoor rated raceways; this guide covers using raceways outdoors.

Clean and Professional Interiors

Raceway (Indoors)

Raceways are most popular indoors to make the space look clean and professional. There are also outdoor rated raceways. This guide covers using raceways indoors.

Ethernet Wall Plates

Not recommended. It can be difficult to find a wall plate that passes POE power and provides grounding. These devices also provide a secondary point of failure, and take up far more room than a cable pass through plate for larger systems.

Dealing with Long Distance

Using POE switches to reduce cabling

You can run one cable to a POE switch and then run several cameras to that switch, however, POE switches are not plug-n-play. POE switches do require you to know a decent amount about computer networking.

Cables run over 300 feet

Cat5e and Cat6 cable data has a limit of 300 feet, but if you need to go further than that you can use a POE extender, POE injector, or POE switch to hear and repeat the signal. This article discusses when you would use each of these tools.

Long Distance Wireless

Military-Grade Long-Range Wifi Solution are used when attempting to send wireless IP Camera video data more than 100 feet (and up to 3 Miles). These products will require a professional wireless network technician on location.

Part 4

Mounting Cameras and Recorders

Basic Camera Installation

Bullet Cameras on Walls

In this guide, we will be installing a bullet camera on a wall.

Bullet Cameras on Ceilings

In this guide, we will be installing a bullet camera on a ceiling.

Bullet Cameras on Soffits

In this guide, we will be installing a bullet camera on a soffit.

Dome Cameras on Ceilings

In this guide, we will be installing a dome camera in a ceiling tile.

Dome Cameras on Walls

In this guide, we will be installing a dome camera on a wall.

Positioning the Lens in our Dome Cameras

In this video guide, we demonstrate how to adjust the lens positioning on our Marshall, Guardian, Warden, and Mosquito Dome Cameras.

Audio and Alarm Inputs FAQ and Sample Wiring Guide

Here’s a guide on Line-Level Audio Inputs and Analog Wired Alarm Integration.

Attaching Our Camera Mounting Accessories

Electrical Mounting Boxes

Our electrical box mounts are used to give easy access to your connections, hide them inside the junction box, and allow you to drill a smaller hole in your wall. If you want to run conduit they are necessary to run conduit straight to the camera.

PTZ Wall Mount Bracket

This guide will show you how to mount your PTZ camera to the wall mount bracket.

Pole Mounts

In this guide, we will be installing a Hornet Pro bullet camera on a pole.

Pendant Mounts

In this guide, we will be installing a Radius panoramic dome camera on a pendant mount. You can install all our PTZ and a few of our dome cameras via Pendant mounts.

Screw Size Chart

Lose a screw? No problem. Here’s all our 2018 product line screw sizes in one convenient place.

NVR Mounting Options and Hard Drive Installation

Shelf / Desk Mounting NVRs

This is what most people do: just put it on a shelf or desk. This makes it easy to connect to a TV/monitor and use the mouse (included) to control the NVR.

Rack Mounting NVRs

Companies often want to put the NVR in their server rack room. People who do this often to control the NVR only through our apps or web browser. Only our larger NVRs (16 channels and up) are wide enough to be rack mounted (and they come with ears). Our smaller NVRs can use our Rack Mount Shelf.

Wall Mounting NVRs

Many people choose to mount their NVR on a wall near a TV. To do this, you will want to purchase a vertical rack, like this one that matches the height of your NVR. The 16, 32, and 64 channels units have a height of 2U and the 128 channel is 3U. NVRs are heavy and you will want to make sure your wall can support the weight.

Mounting NVRs behind a Wall / in an Attic

People who are afraid of the theft of an NVR often place it behind a false wall or in an attic. People who do this control the NVR only through our apps or web browser. Be aware: Not all attics are insulated well enough to be within the temperature requirements of the NVR. Temperature range is listed on each NVR’s technical specs tab.

“NVR” Lock Boxes

There’s a few companies advertising “NVR Lock Boxes,” but any Server Rack or Computer Rack will do. Most Server Racks or Mounts have locks on them already. This picture is of a Tripp Lite Server Rack with Lock It houses a 32 channel NVR, two of our POE Switches, and a router, but there are tons of companies selling small server racks online.

NVR hard drive installation

If you purchase both a hard drive(s) and recorder from us, we will happily install the hard drive for you. but here’s a handy guide if you want to do it yourself.

Part 5: Specialized Work

When to NOT DIY – Get an Expert

Long Distance Wireless

Military-Grade Long-Range Wifi Solution are used when attempting to send wireless IP Camera video data more than 100 feet (and up to 3 Miles). These products will require a professional wireless network technician on location. We can’t offer support on this product remotely, as once we can see it remotely, that means that it is already working.

Aerial Cable

Aerial cable clearance varies based on location (cable over a road needs more clearance than over a sidewalk, for example), needs to be enclosed within 8 feet of finished grade, and requires a on-site structural analysis to make sure the cable won’t break. Hire an expert.

Burial of Cable

Number one, call 811 before you ever dig: know where your power company has buried its power cables! The required cable burying depth also can vary based on your local zoning laws and your certificate of occupancy; you should get an expert.

Elevators

Don’t even try to install any cable in one without a licensed elevator technician’s help as the cable needs to be inside the cable traveler. An error in securing the cable can result in damage to the elevator’s operation – and potentially the people inside it. Don’t mess with it; get a licensed elevator technician to run the cable.

<p>The post Security Camera Installation Guides v2 first appeared on NVR IPCAMERA SECURITY.</p>

TetherX Camera Setup Guide v2, Tether your video surveillance, alarm panels, network infrastructure and other IP or Serial devices to the cloud. Monitor the health of your sites, cloud record cameras and integrate with third party services.

The steps required to set up Samsung Cameras / DVRs and NVRs

Setting Correct Profiles

Please ensure you have 2 profiles configured on your device:

IP Cameras

Cameras are the easiest to set up and should work out of the box. If the cameras are not working for any reason, please try one of the following for the Analytics Path and Recording Path:

Multi-Sensor IP Cameras & Encoders

If your device is a multi-sensor camera or an encoder, please set the Analytics Path as follows:

NVR – Network Video Recorders

DVR – Digital Video Recorders

DVR recorders setup is similar to NVR setup with the following differences:

.

Can I use TetherX alongside HikConnect?

Can I use Hik-Connect on my Hikvision cameras and recorders?

Yes.

Please make sure that stream encryption is switched off under Configuration > Network > Advanced Settings:

HikConnect stream encryption uses a proprietary mechanism which is not available to third-parties. Please note TetherX will encrypt the stream to the highest standards, for more information please see our security white-paper.

Note: If you are still getting a broken stream or no live view, please try updating the camera and/or recorder firmware to the latest. There are known issues that have been addressed by Hikvision.

.

Live View – Technical Implementation Details

How TetherX implements live view to be compatible with all manufacturers

Introduction

The quality, latency and smoothness of live view streaming is dictated by many factors:

Available Streams from Cameras

Typically cameras will provide 2 video streams as well as the ability to request a single image. These limitations dictate what is and isn’t possible when it comes to both recording and streaming.

💡 Note: More expensive and speciality cameras will provide additional video streams and custom streams of crops/de-warps of the same image (e.g. 180 or 360 cameras).

The streams are usually accessed through RTSP and the images through HTTP. For example:

Formats

Transcoding vs Proxying

TetherX supports both transcoding and proxying/packaging. The differences between the two are as follows:

Transcoding is a process of taking the stream from a camera, decoding it and then re-encoding it into a different format. This is the ideal method to hit a specific requirement of Internet bandwidth and viewing size, but it is in most cases cost prohibitive as you need power hungry and expensive hardware to achieve.

​For context, a TetherBox Pico capable of recording 10 cameras will only be able to record 2 if transcoding (you can enable transcoding in TetherX by editing a camera and switching to the advanced tab).

Proxying & Packaging is what is used in most cases, where the original video stream is maintained but is packaged into different containers, for example .mp4 for video recording and .ts for local and high-def live streaming (see streaming technologies below).
​

This means that ultimately, you are at the mercy of the camera/recorder. If you need to open 16 cameras and each one is 1mbit, but your upload speed is only 10mbit, it will simply not work because the stream size cannot be adjusted without either:

Video vs Images

TetherX use a combination of images and video to achieve different goals. It is important to understand the differences and advantages/disadvantages of each, which in turn dictate when either is used in TetherX.

The main difference between image and video compression is every image is self contained, where every video frame is part of a stream. While you may skip an image, skipping a frame in a video stream leads to parts of the image breaking / disappearing:

Systems that ignore broken/skipped data (e.g. streaming over UDP) will show a broken image while many systems will simply show a loading spinner while they wait for the next key frame (which is controlled by the key-frame interval set on the camera/recorder, typically set to 1 second, or the same number as fps, but sometimes much longer).

Because each image is self contained, it is typically 5 to 25x larger in bitrate vs video at 25 images per second. It may initially seem obvious that video should be used when accessing remotely, however there are certain important underlying trade-offs that make it a much tougher question which needs to be evaluated on a case by case basis, according to the following:

Advantages of Images

Live View Streaming Technologies

TetherX uses all mainstream streaming technologies available and choses between them depending on the specific requirements and constraints:

How TetherX Does It

TetherX supports most streaming technologies and switches between them depending on context.

When local streaming (the TetherBox is able to detect if you are on the same network), if we are viewing less than 10 cameras simultaneously TetherX switches to LHLS (see above) to show the primary video stream from each camera at full resolution/frame-rate (assuming your viewing device is capable of displaying this many streams). If this is not working well for you, you are presented with a toggle to switch off High-def streaming to fall back to loading images.

When full screening a camera (double tap/click a camera), we assume you want the higher quality and we switch to the full primary stream. If your connection is not able to sustain this stream, we automatically fall back to loading images.

When viewing multiple sites / cameras over Internet in record mode, we switch to image viewing but we transcode/transize the images depending on the size of each live view box on your screen. This ensures that you are able to view many simultaneous cameras, the latency is lower than video, it automatically adapts to the available bandwidth and it does not impact recording quality. This does however mean a lower fps.

When viewing multiple sites / cameras over Internet in monitor mode, we proxy the connection directly to the image provided by the camera. This leads to a further lowering of fps but ensures the TetherBox can monitor the health of and provide live view of 10x more cameras than in record mode.

Learn more about using Live View in TetherX here.

How Hikvision iVMS Does it

Because of the constrains outlined above, in order to show smooth video in iVMS (and Dahua PSS) software, if the connection speeds both on site and viewing device cannot accommodate the streams, the software temporarily reconfigures the cameras to send a lower bitrate stream while keeping the resolution the same.

💡 Note: if you happen to kill the software at this point (or lose connection), this can cause the camera to permanently record in lower quality.

Because many cameras or recorders only support a single stream at above D1 resolution, this means that not only is the live view quality reduced, but also the video being recoded which can lead to losing critical video evidence.

In our testing, limiting the connection to 5mbit 200ms upload and streaming just 4 cameras in HD resulted in blocky and usable footage being recorded on the NVR. It also took over 10 seconds to get an initial image, however the motion was smooth (25fps) once loaded.

In comparison when using images (outside of the iVMS/PSS software), the images loaded almost immediately, the image quality was significantly higher, but the frame-rate was poor (3-4fps) – still sufficient for making decisions in a control room setting, but understandably disappointing in smoothness by comparison. (Note: higher fps can still be achieved by full screening a single camera on demand).

When viewing a smaller number of cameras from the same manufacturer on a single PC or phone, it looks impressive to have smooth 25fps video on iVMS/PSS/others. However, when dealing with 100+ or even 32 cameras, from different manufacturers, different firmware versions, with multiple users, across multiple sites, with differing and fluctuating bandwidths, you begin to appreciate the trade-offs and advantages/disadvantages of each approach.

💡 Note: This approach of custom code to adjust Hikvision camera settings to achieve smoother live view is only suitable if you do not care about recording quality and you are optimising for a single manufacturer with compatible models/firmware.

​TetherX is an open platform with a focus on convention over configuration, we prioritise the integrity of recorded footage above live view and we implement approaches that work across all recorders/cameras as well as viewing devices.

.

Uniview / UNV Camera Setup Guide (for use with TetherX)

Using TetherX with Uniview / UNV Cameras

Summary

Uniview or UNV cameras should work out of the box in most cases. However please note depending on the age of the camera and firmware versions, the RTSP path may be different.

Please try the following paths:

3. Open the Advanced tab and enter the required Analytics Path and Recording Path. Please try all the paths given as examples above.

.

Camera Setup Checklist

Adding IP cameras to TetherX Please note your camera may have a different interface and options may be located in a different part of the interface. Please refer to the camera manual if you are not able to find the relevant option.

Network

Set a Static IP

Set camera to unused IP on 192.168.88.x network
set DNS/Gateway to 192.168.88.100

Important: Although it’s possible to configure your camera with DHCP, and TetherBox is capable of detecting any IP changes, we strongly advise against this practice for security reasons. This setting can potentially allow the camera to connect directly to the internet, raising a range of security issues. These include unauthorised access through back doors, or the risk of security holes in the camera’s firmware if it’s not updated regularly.

Video & Audio

Recording Stream (primary)

Analytics Stream (secondary)

Conditions

.

Audio (optional)

Date & Time

One option is to disable time from being displayed in the camera at all. You generally do this under OSD settings. If you do wish time to be displayed in the image, you need to set the following:

<p>The post TetherX Camera Setup Guide v2 first appeared on NVR IPCAMERA SECURITY.</p>

Lorex Fusion: Download the Lorex App

The following article provides instructions for downloading the Lorex App and connecting your Lorex Fusion Collection recorder to the app.

Prerequisite

Before you start, your Fusion recorder must be powered on and connected to your router using the included Ethernet cable. For Basic System Setup instructions, refer to your Fusion recorder’s Quick Start Guide or Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

Download the Lorex App

Once your Fusion recorder has connected to the Lorex App, complete the final Fusion steps by connecting your Fusion Wi-Fi cameras and accessories.

For setup instructions using the new local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (New Local UI).

For setup instructions using the previous local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories.

Lorex Fusion: Frequently Asked Questions

The following frequently asked questions (FAQs) provide more information about your Lorex Fusion Collection. Where applicable, the FAQ includes links to articles where you may find more information.

Lorex Fusion Troubleshooting FAQ.

What is Lorex Fusion?

Our Lorex Fusion recorders incorporate the newest (fusion) technology to connect both Lorex Wired and Fusion Wi-Fi Cameras, Doorbells, Floodlights, and Sensors to one system. Lorex Fusion Wi-Fi Cameras and Accessories can connect to one recorder for continuous 24/7 recording and local, secure storage (up to 10TB). Everything can be accessed from your Lorex App for easy control of all devices.

.

Why do I get an offline message and a blank screen for the (B463AJ) 2K battery doorbell’s channel on the Fusion recorder?

Being a battery-operated doorbell, it will always go to sleep after a period of inactivity to conserve battery life. Once the doorbell is correctly paired to your Fusion recorder, the offline message means the doorbell has gone to sleep but is still connected and can be awakened. When motion is detected, or when the call button is pressed, there will be live video from that channel. You can also manually wake up the doorbell through the Lorex app, by activating the liveview.

.

Can my Battery Video Doorbell record continuously?

To conserve battery life, Wi-Fi Battery Video Doorbells only record when motion is detected. They do not record continuously.

.

Which recorders are part of Fusion?

For a list of Lorex Fusion Recorders, please refer to the Product Compatibility Chart.

.

Can I connect all Lorex Wi-Fi Cameras and Accessories to my Fusion recorder?

Only Lorex Fusion Compatible Wi-Fi Cameras and Accessories can connect to Lorex Fusion Recorders.

.

Which Lorex Wi-Fi Cameras and Accessories are part of Fusion?

See the following list of Lorex Fusion Wi-Fi devices:

.

Should I update my Lorex Fusion recorder’s firmware?

It is recommended to update your system firmware to the latest version to ensure remote connectivity and to support newly added Fusion Wi-Fi devices.

.

Does my Lorex Fusion recorder require a network setup?

Yes, a network setup is required to connect Fusion Wi-Fi cameras and accessories to your Fusion recorder. Ensure you connect the included Ethernet cable to your recorder’s LAN port and your router.

.

Does it matter which router I use?

Yes, due to its strong signal, the dual-band router is suitable for high resolution video recording and for connectivity between devices. Ensure that your Fusion Wi-Fi cameras and accessories and your Fusion recorder are all connected to a dual-band router (2.4 GHz/5 GHz bands).

.

How many Lorex Fusion Wi-Fi Cameras and Accessories can I connect to my Fusion recorder?

This depends on your Fusion recorder and the number of Fusion Wi-Fi channels it comes with. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

What is a Fusion Wi-Fi channel?

A Fusion Wi-Fi channel is the channel you use to add a single Fusion Wi-Fi camera to your system. A 16-channel security system with 8 PoE ports/channels (for wired camera connection) and 8 Fusion Wi-Fi channels means that 8 Fusion Wi-Fi cameras and accessories can connect to the entire system.

Note: Fusion Wi-Fi channel’s are only available on certain Lorex Fusion recorders. For a list of Fusion recorders, see the Product Compatibility Chart.

.

How many Fusion Wi-Fi channels are on my Lorex Fusion Recorder?

The number of Fusion Wi-Fi channels varies per Fusion recorder. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

How do I setup my Lorex Fusion system?

Complete your Fusion setup in the following order:

After connecting your Fusion system, ensure you adjust your Fusion settings.

.

Are there Fusion setup tutorial videos?

For a video walk-through of the Fusion setup with the new local UI (N845, N846, N847, N864, D863, D881 Series), please watch here.

For a video walk-through of the Fusion setup with the previous local UI (N841, N842, N843, N844, N861, D862, D871 Series), please watch here.

.

How do I setup my Lorex Fusion recorder and wired cameras?

For Basic System Setup instructions, refer to your recorder’s Quick Start Guide or Series Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

How do I connect my Lorex Fusion Wi-Fi camera or accessory to my Fusion recorder?

For full setup instructions, please click on the article corresponding with your model number.

.

Which password should I enter to connect my Lorex Fusion Wi-Fi camera or accessory to my Fusion recorder?

Enter the same password that you created in the Lorex App when setting up your Fusion Wi-Fi device.

.

What is continuous recording?

Once your Lorex Fusion Wi-Fi camera connects to your Fusion recorder, your camera’s recording settings are automatically set to continuous. This means that your Fusion Wi-Fi camera will record 24/7 or for the entire duration of the recording schedule onto your Fusion recorder’s hard drive. It is worth noting that recordings on the camera are limited due to the size of its onboard storage, while recordings on the recorder are extensive (3TB to 10TB). Continuous recording captures everything in the background, and you can playback to catch anything you missed.

.

Do all Lorex Fusion Wi-Fi cameras record continuously?

No, to conserve battery life, battery-operated video doorbells do not record continuously (24/7).

.

How do I set my Lorex Fusion Wi-Fi camera to continuous recording?

After Fusion setup, your Wi-Fi camera is automatically set to Continuous recording. To adjust your camera’s recording settings, login to your recorder and navigate to the devices menu. For instructions, please see the article Lorex Fusion: Adjust Settings.

Note: Battery-operated video doorbells do not record continuously (24/7). Being a battery-operated doorbell, it will always go to sleep after a period of inactivity to conserve battery life. Once the doorbell is correctly paired to your Fusion recorder, the offline message means the doorbell has gone to sleep but is still connected and can be awakened. When motion is detected, or when the call button is pressed, there will be live video from that channel. You can also manually wake up the doorbell through the Lorex app, by activating the liveview.

.

How come I’m receiving duplicate notifications in the Lorex App?

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder. For instructions, please see the article Lorex Fusion: Adjust Settings.

.

After Fusion setup, where is my Lorex Fusion Wi-Fi camera’s video footage being stored?

Your Lorex Fusion Wi-Fi camera saves recorded motion detection videos onto the local microSD card (not always included). Once you’ve connected your Fusion Wi-Fi camera to your Fusion recorder, your camera’s recording settings is automatically set to 24/7 Continuous recording, and all recorded video is stored on your recorder’s extensive hard drive (up to 10TB).

.

What features are supported in my Fusion recorder vs. the Lorex App?

Please see the following list of features supported in either your Fusion recorder and/or the Lorex App:

.

Can I use my web browser to access my Lorex Fusion Wi-Fi camera?

You can only access your camera on the Lorex App, recorder, or on the Lorex Cloud Client.

.

When modifying the password in the Lorex Cloud Client, which password should I enter?

Enter the password for your Wi-Fi camera or accessory created in the Lorex App during setup.

.

Where can I order the Lorex Fusion Collection?

To order, go to lorex.com.

Lorex Fusion: Troubleshooting

The following article provides some troubleshooting tips for setting up your Lorex Fusion Collection.

.

My Fusion Wi-Fi camera or accessory is not appearing in the device list.

.

My Fusion Wi-Fi camera or accessory is not connecting to my Fusion recorder.

• Give your Fusion Wi-Fi camera or accessory a few minutes to establish a connection.

• Check to see if your Fusion recorder has the most up-to-date firmware. New Local UI: Login to your recorder and navigate to System > Update & Reset > Upgrade, then click Check for Updates.  Previous Local UI: Login to your recorder and navigate to Main Menu > Information > Update/Reset > Update, then click Check for Updates. For instructions on updating your recorder’s firmware through USB, see the article How to manually upgrade the firmware of your recorder.

• Ensure that your Fusion Wi-Fi cameras and accessories and your Fusion recorder are powered on.

• The same password created for your Fusion Wi-Fi camera or accessory in the Lorex App must be entered in your Fusion recorder. If you have forgotten the password, then reset your Fusion Wi-Fi camera or accessory and connect it to the app again.

• (Applies to the previous local UI only) If your password for your Fusion Wi-Fi camera or accessory is entered incorrectly in your Fusion recorder, then your Wi-Fi device will lock itself. Reset your Fusion Wi-Fi camera or accessory and connect it to the app again.

• Ensure that you are entering the password for your Fusion Wi-Fi camera or accessory created in the Lorex App, and not the Lorex App account password. Those are two separate passwords.

• Ensure that your Fusion Wi-Fi camera or accessory is connected to a dual-band router (2.4 GHz/5 GHz bands).

• Ensure that you are connecting the Fusion Wi-Fi camera or accessory to an available Fusion Wi-Fi channel, and not a Wi-Fi channel that already has a Wi-Fi device connected to it.

.

I don’t know the password for my Fusion Wi-Fi camera or accessory.

If you don’t know the password for your Fusion Wi-Fi camera or accessory, then you will need to reset the device and connect it to the Lorex App again.

To reset your Fusion Wi-Fi camera or accessory:

.

I’m receiving duplicate notifications in the Lorex App.

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder. For instructions, please see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N910 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi Cameras and Accessories to your N910 Fusion recorder.

.

Our Lorex Fusion recorders incorporate the newest (fusion) technology to connect both wired and Wi-Fi cameras, doorbells, floodlights, and motion sensors to one system. All Fusion compatible Wi-Fi cameras and devices connect to one recorder for continuous 24/7 recording and private local storage. Access everything from the Lorex App for easy control of all devices.

Note: To conserve battery life, Wi-Fi Battery Video Doorbells only record when motion is detected. They do not record continuously.

For any connection issues, see the article Lorex Fusion: Troubleshooting.

.

Part One — Wired Setup

Setup your Fusion recorder and wired cameras. For Basic System Setup instructions, refer to your recorder’s Quick Start Guide or Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

Important: Network setup is required for your system — use the included Ethernet cable to connect your recorder to your router.

.

Part Two — Connecting your Lorex Fusion Wi-Fi Camera

Connect your Lorex Fusion Wi-Fi Camera to the app and then from your recorder scan your network to add it.

.

Option A — Connecting Your New Lorex Fusion Wi-Fi Camera to Your Recorder

Add compatible Lorex Fusion Wi-Fi Cameras and Accessories onto Fusion Wi-Fi channels on the recorder.

To connect your New Lorex Fusion Wi-Fi Camera to the recorder:

Note:

.

Option B — Connecting Your Existing Lorex Fusion Wi-Fi Camera to Your Recorder

Add compatible Lorex Fusion Wi-Fi cameras and accessories onto Fusion Wi-Fi channels on the recorder.

Note:

To enable remote viewing for the mobile app, you will need to:

To connect your Existing Fusion Wi-Fi camera to the recorder:

1.From the Live View display, click the pair icon  in the center of the Fusion Wi-Fi channel’s screen.

Note: It may take a few minutes for your Lorex Fusion Wi-Fi Camera’s video feed to appear.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N845, N846, N847, N864, D863, D881 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi cameras and accessories to the Lorex App and to your Fusion recorder.

Note: These Fusion instructions apply to the new local UI only. For Fusion instructions that apply to the previous local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories.

.

Before you start

.

Watch the Lorex Fusion setup tutorial video

For a video walk-through of the fusion setup, please watch here.

.

Connect your Fusion Wi-Fi cameras and accessories to the Lorex App

Follow the Lorex App steps to add your Lorex Fusion Wi-Fi cameras and accessories. Refer to your camera’s documentation at help.lorextechnology.com for detailed setup instructions. Search your camera’s model number to access the product support page.

Note:

2.In-app, tap the  icon to add your Wi-Fi camera.

.

Connect your Fusion Wi-Fi cameras and accessories to your Fusion recorder

Note: You can add one Wi-Fi camera or accessory to one Fusion Wi-Fi channel. The number of Fusion Wi-Fi channels varies per Fusion recorder. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

2.From the Live View display, click the pair icon  from the center of the Fusion Wi-Fi channel.

Note: If your Lorex Fusion recorder and Fusion Wi-Fi camera share the same password, then the devices will automatically connect without entering the password.

.

After successfully connecting to your Fusion recorder, your Fusion Wi-Fi camera or accessory connection status turns green. For any connection issues, see the article Lorex Fusion: Troubleshooting.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N841, N842, N843, N844, N861, D862, D871 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi cameras and accessories to the Lorex App and to your Fusion recorder.

Note: These Fusion instructions apply to the previous local UI only. For Fusion instructions that apply to the new local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (New Local UI).

.

Before you start

.

Watch the Lorex Fusion setup tutorial video

For a video walk-through of the Fusion setup, please watch here.

.

Connect your Fusion Wi-Fi cameras and accessories to the Lorex App

Follow the Lorex App steps to add your Lorex Fusion Wi-Fi cameras and accessories. Refer to your camera’s documentation at help.lorextechnology.com for detailed setup instructions. Search your camera’s model number to access the product support page.

Note:

2.In-app, tap the  icon to add your Wi-Fi camera.

.

Connect your Fusion Wi-Fi cameras and accessories to your Fusion recorder

Note:

After successfully connecting to your Fusion recorder, your Fusion Wi-Fi camera or accessory connection status turns green. For any connection issues, see the article Lorex Fusion: Troubleshooting.

To turn off duplicate notifications, adjust your camera’s recording settings, or link motion sensors to cameras, see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Adjust Settings

The following article provides instructions for adjusting your Lorex Fusion Collection settings.

.

Turn off duplicate notifications

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder.

To turn off duplicate notifications:

2.Under your Fusion recorder, swipe left to find your Fusion Wi-Fi camera or accessory.

3.Tap on your Fusion Wi-Fi device’s notification icon .

.

.

Adjust the recording settings for your Fusion Wi-Fi camera or accessory

After Fusion setup, your Lorex Fusion Wi-Fi camera’s recording settings will automatically adjust to Continuous, recording 24/7 directly to your recorder’s hard disk drive.

To adjust the recording settings (new local UI):

To adjust the recording settings using the previous local UI, navigate to Main Menu > CAMERA > Recording > Recording and follow the same steps as above.

.

Set the recording schedule for your Fusion Wi-Fi camera or accessory

You can set a custom recording schedule according to your needs. For example, you can set the system to record continuously during business hours and record on motion detection only outside of business hours.

• Click-and-drag on each day to customize the recording schedule. The schedule is set up as a grid, with each block representing two hours.

• Click  beside 2 or more days to link schedules (). This allows you to quickly change multiple schedules at once.

• To make fine adjustments to a schedule, click . This will allow you to set exact start and end times for a schedule.

• To disable all recording of the selected type on the selected day, click .

To set the recording schedule using the previous local UI, navigate to Main Menu > STORAGE > Schedule and follow the same steps as above.

.

Link sensors to cameras

Once you’ve completed the Fusion setup, you can link motion and door/window sensors to any compatible camera, so that when the sensors are triggered the linked automatically cameras record.

.

To learn more about using your Lorex Fusion system, visit the Fusion page or refer to the Lorex Fusion: Frequently Asked Questions article.

.

<p>The post Lorex Fusion Troubleshooting FAQ first appeared on NVR IPCAMERA SECURITY.</p>

ATTENTION: Prior to purchasing and installing an accessory antenna, read the product specifications of your receiver to determine if your receiver has a weatherproof housing. Installing your weatherproof receiver outdoors provides a better line-of-sight between the receiver and the camera, increasing the strength of the wireless signal. See your product specifications to determine the weatherproof rating of your receiver.

The Directional Wireless Panel Antenna and the Omni-Directional Antenna are used to extend the range of one or multiple wireless or wire-free cameras.

Directional Wireless Panel Antenna (ACCANTD9)

Omni-Directional Antenna (ACCANTO8)

Use the 2.4GHz Directional Wireless Panel Antenna (ACCANTD9) to focus a wireless signal onto one specific wireless device (camera or receiver) to increase the range of transmission. A clear line-of-sight between the antenna and the wireless device needing range extension is required.

Use the 2.4GHz Omni-Directional Antenna (ACCANTO8) to enhance the signal of one or multiple cameras that are paired to a single or dual antenna receiver. You may also use two Omni-Directional Antennas to extend the range of all cameras paired to a dual antenna receiver.

REQUIREMENT: To connect the antenna directly to the camera or receiver, the device must have a removable SMA type antenna. Visit www.lorextechnology.com/compatibility to ensure the antenna is compatible with your camera or receiver model.

Lorex Wireless Cameras and Monitors guide 2024

Also Read  : Lorex Camera Troubleshooting

Recommended Antenna Installation Methods

Your antenna needs will vary depending on the setup of your camera system, the number of cameras that require range extension, and the number of channels on your wireless receiver. Review the scenarios below to ensure you have the correct antenna and installation method to meet your needs.

Click a setup scenario to see the recommended installation method:

Combining Accessory Antennas

If you have installed your accessory antenna according to the recommended installation methods and would like to enhance wireless signal strength even further, you may add an additional Directional Wireless Panel Antenna (ACCANTD9) directly to a camera. The additional Directional Wireless Panel Antenna can be used with a Directional Wireless Panel Antenna or with an Omni-Directional Antenna attached to the receiver.

Click an antenna combination to see recommended installation methods:

Scenario 1: Extend the range of one camera paired to a single antenna receiver

To extend the range of one camera connected to a single channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9).

The Directional Wireless Panel Antenna can be connected in two configurations.

Configuration 1. Connect the antenna directly to the camera

Configuration 2. Connect the antenna directly to the wireless receiver

REQUIREMENT: The antenna connects using an SMA cable and replaces the existing antenna on either the camera or wireless receiver. Check www.lorextechnology.com/compatibility to determine if your product is compatible with the antennas.

Scenario 2: Extend the range of one camera paired to a dual antenna receiver

To extend the range of one camera connected to a multi-channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9). Connect the Directional Wireless Panel Antenna directly to the camera.

Scenario 3: Extend the range of select cameras paired to a dual antenna receiver

To extend the range of select cameras on a multi-channel receiver, use the Omni-Directional Antenna (ACCANTO8).

Connect the Omni-Directional Antenna to one of the antenna ports on the wireless receiver.

REMINDER: Each antenna port on a dual antenna receiver is associated with specific camera channels. One antenna communicates with odd numbered channels (1, 3, and 5), while the other antenna communicates with even numbered channels (2, 4, and 6). See the table below for dual antenna channel configurations.

If you connect the Omni-Directional Antenna to an antenna port and your wireless signal does not improve, try switching the Omni-Directional Antenna to the other antenna port or pairing your camera to a different camera channel.

Scenario 4: Extend the range of all cameras paired to a dual antenna receiver

To extend the range of all cameras on a dual antenna receiver, connect an Omni-Directional Antenna (ACCANTO8) to each antenna port on the receiver.

IMPORTANT: Two Omni-Directional Antennas are required to accommodate this setup.

Combination 1: Combine two Directional Wireless Panel Antennas

If you are using a Directional Wireless Panel Antenna (ACCANTD9) to enhance the signal of a single camera with a single channel receiver, you can use an additional Directional Wireless Panel Antenna to further enhance the wireless signal.

Connect one Directional Wireless Panel Antenna directly to the camera and one Directional Wireless Panel Antenna directly to the wireless receiver. To maximize signal strength, it is recommended to aim the two antennas directly at each other with a clear line-of-sight.

Combination 2: Combine a Directional Wireless Panel Antenna with an Omni-Directional Antenna

If you are using an Omni-Directional Antenna (ACCANTO8) to enhance the signal of multiple cameras, you can further enhance the signal of a specific camera by connecting a Directional Wireless Panel Antenna (ACCANTD9) directly to the camera.

A clear line-of-sight between the Directional Wireless Panel Antenna and the Omni-Directional Antenna is recommended to maximize signal strength.

Lorex SD Pro App: Changing / resetting the password

If the password for the Lorex SD Pro app to view the Wireless Home Monitor is lost or forgotten it will need to be reset.

To reset the Lorex SD Pro app password:

1.Ensure that your Wireless Home Monitor is connected to a network router using the included Ethernet cable.

2.On the Wireless Home Monitor tap the Menu icon ().

3.Use the joystick to select Settings > Network > Reset Password.

4.Select Yes to confirm.

5.Tap the Menu icon () repeatedly until all the menus are closed.

6.Launch the SD Pro app and enter the default password. Refer to your user manual for your default password. You will be prompted to create a new password.

Lorex SD Pro App: Setting up Wireless Home Monitor remote access

You can access and view wireless cameras from a Wireless Home Monitor system using an iPhone, iPad, or Android smartphone or tablet using the Lorex SD Pro app. It is available at the App Store or Google Play Store.

Prerequisites:

To set up the mobile application:

LW2700 Wireless Home Monitor: Included cables and accessories

LW2700 Series Wireless Home Monitors support wireless cameras using a wireless signal. They do not have an internal battery and require a connection to a power source. Refer to your user manual for model specific information on cables and accessories. Click here for downloads and documentation for your product.

Most wireless home monitors include the following cable connections and accessories when purchased:

Network: Wireless camera Internet requirements

Standard wireless cameras that connect to a DVR / NVR, do not need access to the Internet to function. Stand-alone IP cameras do not require an Internet connection for basic functions, but an Internet connection is required for full functionality.

Security Cameras: Understanding Field of View (FOV)

Field of View (FOV) is the maximum observable area that is seen at any given moment through an optical device such as a camera lens. The coverage of the area can be measured using the horizontal and vertical distances to find the diagonal of the area in degrees. Mathematically, the FOV is calculated using the horizontal dimension of the sensor (h) and the Focal Length (F).

You can find the camera’s Field of View details in the Specifications sheet. Click here for additional support content including security camera documentation.

The Camera Lens, Sensor and Focal Length

Focal length (F) is the distance between the center of a lens and its sensor. The size of the lens is the aperture size.

These factors affect field of view. A narrower focal length captures more of the scene and displays a larger field of view. A wider focal length magnifies a scene and decreases the field of view. The higher the focal length value the lower the FOV.

Types of Camera Lenses

Fixed: a fixed camera focal length provides an Angular FOV which is permanently set and cannot be adjusted by the user. Varifocal: the camera focal length can be manually adjusted by the user. Generally, this is done manually with screws or dials. At Lorex we have motorized varifocal cameras that allow you to digitally zoom using your phone or NVR without losing details. These lenses provide flexibility and customization for your camera image needs.

The importance of Field of View

A wide angle lens or smaller lenses produce a greater field of view and captures more objects in a scene enhancing your ability to cover larger and wider areas such as foyers, parking lots or warehouses.

A narrow angle lens or larger lenses produce a smaller field of view; capturing a limited area, but the camera quality image improves in detail. These are designed to monitor a specific object, such as cash registers, entrances/exits, hallways or objects of value.

How to Calculate the FOV

To calculate the FOV requires the sensor size and the focal length of the lens: h = Sensor Size F = Focal Length of the Lens

FOV is represented by this equation: FOV = 2tan-1(h) / 2F

Example: h = 4.7mm F = 6mm FOV = 2tan-1(h) / 2F = 2tan-1(4.7)(12) = 2tan-1(0.39) = 2(21.4°) = 42.8°

W482CAD – 2K Wi-Fi Camera : Frequently Asked Questions

The following FAQ article answers many of the general questions about the 2K Wi-Fi Camera with Smart Deterrence (W482CAD). Where applicable, the FAQ includes links to articles where you may find more information.

.

Where do I place my Lorex 2K Wi-Fi Camera?

.

How should I position my Lorex 2K Wi-Fi camera?

When mounting the camera on a wall, make sure of the following:

 Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

.

How do I enable motion detection and person detection?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap  icon to enable Motion Detection.

Note: If motion detection is disabled, general/person/vehicle detection will automatically disable and you will not receive any motion detection notifications in the Lorex App.

.

How do I customize Motion Zones™?

Motion Zones™ allows you to customize your device’s motion detection region. Motion Zones™ screen consists of the following settings:

To set Motion Zones™

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap Motion Zones™.

 For full instructions on how to set customized Motion Zones™, see Configuring Motion Zones™.

.

Why am I receiving so many notifications?

There are a few ways you can lower the number of notifications you are getting.

.

How do I enable Color Night Vision?

1.Lauch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap  icon to disable Auto Night Vision.
Note: Disabling Auto Night Vision will force the camera into Color Night Vision mode. Recommended in low-light conditions.

.

How to activate Two-Step Verification?

1.Launch the Lorex App.

2.Tap Settings.

3.Tap Account Settings.

4.Tap Two-Step Verification.

5.Tapicon to enable Two-Step Verification.

For detailed setup instructions, see Two-Step Verification Setup.

.

How to optimize video quality?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Video Settings.

4.Tap  icon to enable HDR (High Dynamic Range).

Note: Enabling HDR optimizes video picture in high-contrast conditions such as under-lit and over-lit areas.
By default, the video quality is set to High (2x1080p HD).

.

What is Home & Away™?

Lorex App can automatically use your location to manage your notifications when you are at home or away. The app will notify you when you are inside/outside of your set home perimeter.

To start using this feature, navigate to your mobile device settings and enable Location services for Lorex App.

For detailed setup instructions, see Configuring Home & Away™.

.

How do I activate the LED deterrence light when motion is detected?

1.Lauch Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Deterrence Light Brightness.

4.Tap  icon to enable camera’s deterrence light whenever motion or person is detected.

.

How do I remove the 2K Wi-Fi Camera from my account?

1.Launch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Remove Device.

.

How to permanently delete data of 2K Wi-Fi Camera?

Refer to Formatting Device Storage for more information.

.

Does my device support WPA2 or WPA3?

Your device supports Wi-Fi Protected Access 2 (WPA2) which is the industry standard security protocol for Wi-Fi networks. WPA2 offers security against unauthorized access and data interception and is supported by most Wi-Fi routers including those that support both WPA2 and WPA3. It employs Advanced Encryption Standard (AES), an encryption mechanism, which secures communication between your camera and Wi-Fi network to keep transmitted data confidential. For information on which devices support WPA2 and which devices support WPA3, please refer to “WPA2 and WPA3 Supportive Devices.”

.

What are the compatible SD cards?

Refer to Compatible SD Cards and Storage Sizes for more information.

.

What devices are compatible with the 2K Wi-Fi camera?

Refer to Product Compatibility Chart for more information.

W482CAD – 2K Wi-Fi Camera : Installation

This article provides instructions to install your Lorex 2K Wi-Fi camera with Smart Deterrence (W482CAD).

.

What is included in the box?

The above contents are based on one camera.

.

How to connect with Lorex App

3.Open the Lorex App app and create an account or login with your credentials.

4.Tap  icon to add a new device, then follow the in-app instructions to complete the device setup.

For full instructions on Lorex App setup, see Connecting with Lorex App.

.

How to mount 2K Wi-Fi Camera to the wall

.

How to mount 2K Wi-Fi Camera to the ceiling

Wi-Fi Security Cameras – How to Read a MicroSD card

To view the contents of a MicroSD card on a laptop or computer, follow these steps:

a. Select the day to play back:

b. Click on the available folder:

c. Within the folder, click either the day folder (Video files) or the jpg folder (Snapshots):

d. Click to select a video time from 00 – 23 hours:

6.Click the MP4 video file to view the video. 

Wireless Home Monitor: Audio not working

If the audio is not working on your Wireless Home Monitor:

• Ensure that the protective film is removed from the camera lens.

• Ensure that the monitor volume is not muted. A mute icon () will be visible on the screen if the volume has been muted.

• Turn the monitor volume up using the volume buttons on the side of the unit. Location will vary by model. For exact location of volume buttons for your model, refer to your user manual. Click here for downloads and documentation for your product.

• The camera must be in Full Screen mode for audio. Tap the Channel Select icon () to switch between channels in Full Screen mode. Audio is disabled in Quad mode.

If audio is not working after increasing the volume and viewing in Full Screen mode, restore the system to default settings.

To restore your monitor to default settings:

CAUTION: Restoring to default settings will erase any setting input on the monitor. Your monitor will need to be reconfigured.

1.On the monitor tap the Menu icon ().

2.Use the joystick to select Settings > Default Settings.

3.Select Yes.

.

<p>The post Lorex Wireless Cameras and Monitors guide 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Disable audio recording on Dahua Recorder

Description

This article is to show how to disable audio function in Dahua IP camera that connected to Dahua NVR.

Video Instruction

Step by Step Instruction

1. Login to Dahua recorder from local system interface.

2. Under Settings, click on Camera.

3. Go to Encode.

4. Select the camera channel.

5. Click on More.

6. Click on the toggle to turn off Audio. Click OK.

7. Click Save.

Dahua NVR Troubleshoot All Series

Read Also : Tuya Camera User Guide Ultimate Manual

Disable audio on Dahua IPC that connected to Dahua NVR

This article is to show how to disable audio function in Dahua IP camera that connected to Dahua NVR.

Video Instruction

Step by Step Instruction

Step by Step Instructions

1. Login to Dahua NVR Web GUI using Internet Explorer.

2. Click on Settings > Camera.

3. Click on Camera list (Some recorder will label it as Registration)

4. Find the camera channel you want audio to be disable, click on E Internet Explorer icon.

5. It will take you to the login page of Dahua IP Camera. Login with Camera credential.

6. Go to Settings > Camera > Audio. By default the Audio settings is enabled.

7. Click on the checkmark to uncheck on both main and substream.

8. Click Save.

.

No Audio from Live Feed

There are following possibilities:

1. Make sure your audio on the computer or television is enabled and working by playing music or watching a video with audio online. You should see this audio meter change when playing music or video on the computer/television.

2. Once you have confirmed your audio is working on your speaker, and if you still can’t hear from your Live Feed, check your connections. If you are using an external microphone that plugs into the camera, please make sure you are supplying power to since the camera does not. See picture below:

.

3. If your connections and power are in order but you still cannot get audio from your live feed, log into your IP Camera or NVR and change the following settings.

4. If you are accessing your audio feed from a computer also make sure you have the speaker symbol enabled to enable audio from the Live Feed.

.

There is Audio from Live Feed, No Audio During Playback

There are following possibilities:

1. Make Sure your camera with a microphone is working via live stream, please follow the NoAudio guide for details.

2. After ensuring you are receiving an audio feed, log onto your NVR and make sure your encoding setup is correct (Setup>Image>Encode>) and make sure your are on the right channel where the camera has a working microphone. Now make sure audio is enabled for either or both the Main Stream and Sub Stream (whichever you are recording on)

3. Also make sure your camera is scheduled to record during specified operation.

4. Also make sure your camera is set to record

5. Now playback a recording of a camera that had picked up audio, you can also simulate this by making noise by the microphone and playing that segment back. Also make sure that the Volume button is not on mute and is turned all the way up during playback.

There is no HDMI output.

Video Loss 1 Camera

There are following possibilities:

Video Loss on Multiple Cameras

There are following possibilities:

Camera Feed is Blurry or Distorted

There are following possibilities:

Video is distorted when searching local records.

There are following possibilities:

Explanation:

1. If Video quality setup is too low then reconfigure video quality setup.

2. If Program read error, bit data is too small. There is mosaic in the full screen. Please restart the DVR to solve this problem.

3. If HDD data ribbon error then replace ribbon.

4. If HDD malfunction then replace HDD.

5. If DVR hardware malfunctions then replace hardware.

Remote control does not work.

There are following possibilities:

Explanation:

1. If Remote control address is not correct then find the correct address.

2. If Distance is too far or control angle is too small then shorten the distance or fix control angle.

3. If Remote control battery power is low then replace battery power.

4. If Remote control is damaged or DVR front panel is damaged then replace remote control or DVR front panel.

System does not boot

There are following possibilities:

NVR Randomly Rebooting or Shutting Down

Issue: NVR Randomly Rebooting or Shutting Down

There are following possibilities: Explanation:

1. If Input voltage is not stable or it is too low, then change the power supply and cable.

2. If HDD malfunction or something wrong with the ribbon, then replace the HDD or the ribbon.

3. Button power is not enough, then add more button power.

4. If Front video signal is not stable then check and adjust front video signal.

5. If Working environment is too harsh, too much dust then clean it.

6. If Hardware malfunction then replace hardware.

How to set the date and time

Time display is not correct.

There are following possibilities: Explanation:

Step by Step Instructions

1. Make sure the “Time Zone” is set correctly.

GMT stands for Greenwich Mean Time.

2. Setup DST, if applicable.

3. “Sync PC” if all else fails.

4. Click, “OK” to save your changes.

Burn error /USB back error.

Explanation:

1. If Burner and NVR are in the same data cable, then separate them.

2. If System uses too much CPU resources. Then please stop record first and then begin backup.

3. If Data amount exceeds backup device capacity which may result in burner error. Then please delete data.

4. If Backup device is not compatible, please change backup device.

5. If Backup device is damaged, please change backup device.

<p>The post Dahua NVR Troubleshoot All Series first appeared on NVR IPCAMERA SECURITY.</p>

What is iCSee?

iCSee is a mobile application designed for remote video surveillance. It allows users to connect and control various security cameras, network video recorders (NVRs), and digital video recorders (DVRs) using their smartphones or tablets. iCSee provides real-time video monitoring, playback, and management of surveillance devices over a network connection. The app offers features such as live streaming, motion detection alerts, two-way audio communication, video recording, and cloud storage options. iCSee is compatible with a wide range of IP camera brands and models, making it a popular choice for home security, business surveillance, and other monitoring needs.

What is iCSee camera?

iCSee Camera refers to any camera compatible with the iCSee mobile application.

Can my camera be connected to iCSee?

iCSee was developed by Xmeye, a company that specializes in security surveillance and video intelligence research and development. They focus on providing technical services, and solutions in the security monitoring field, including various modules, main boards, software, and cloud services.

So, generally speaking, only cameras using Xmeye module solutions can be adapted to iCSee app.

How to install iCSee for PC?

Wired cameras can be accessed on PC by downloading the VMS software. But, for Macbook users, the software currently only supports local area network connection.

For wireless cameras, it is recommended to connect through mobile devices, as accessing via PC may result in connection timeouts or instability.

VMS Downloading (Windows)

VMS Downloading (Macbook)

How to install iCSee app for mobile devices?

iCSee is a free app available for both iOS and Android platforms, offering full functionality without any costs or subscription fees. Follow these simple steps to install it on your device:

.

Explore our camera range: iCSee WiFi cameras, V380 4G cameras, and Ubox solar cameras. Engineered for home security, our cameras are affordable, low-power and durable, and our market share in third world countries is growing rapidly.

.

This tutorial applies to both icsee and icsee pro cameras.
Since the app is always being updated, the interface may be a little different.

Camera description

The details are subject to your manual.

Connect To The Power Supply

Plz connect camera to the power cable,and turn on the power .

If you need to storage the video via the local TF card, plz install the TF card first then turn on the power.

（TF card doesn’t support the hot plugging,  plz plug and unplug memory card when device is power off)

Video tutorial

How To Use Icsee Camera 2024

Read Also : XMEYE NVR Face Recognition guide

.

Register/Login

1.Open”iCSee” app, click “sign up” then use the phone number or mailbox to register account.

2.Register successfully, enter your phone number or mail number in the login interface, enter the password, login your app.

3.You can also use the wechat, facebook, line or the temporary visit to login app.

[Auto-pairing] WiFi Network Configuration

Note: camera can support 2.4G wifi for the time being, doesn’t support 5Gwifi, plz set the router parameter to2.4G first before configuring network, during the connection, phone,router and camera need keep within the 2m distance

1.Phone connect to the wifi network.

2.Click the “+”in the upper right corner click the “Add WiFi camera” according to the device’s voice prompt, follow the app interface guide to enter router’s password,click “confirm” start to configure network(if the device doesn’t appear voice prompt for a long time, you can long press the reset to restore default, then go on to configure network).

3. Enter the search device’s interface, the device is in the connection process, plz wait.

※ Program search, do not operate other programs ;

※ When the camera prompts “succes  sfully connected to router”, it will automatically go to the next step.

※ The camera fails to hear the prompt “succes sfully connect to router”. Please restore factory Settings and match again.

4. After connecting successfully ,interface will prompt to set device’s password and name for your device, after finishing, follow the app interface guide to complete network configuration .

5. After finishing, device will show in the device’s list, it represent the device is connecting successfully.

6. Click it you can view the monitoring image, and do the relevant operation and setting.

Note: Movement tracking is only for indoor ip cameras , bullet ip camera and dome cameras do not have this function

Note: If the automatic etwork configuration fails, you can choose the following two methods to configure the device

The second type: [Manual configuration] Wired network

1. Long press the camera Reset button for 10 seconds to restore the device to factory settings .

2. Connect your router to camera via network cable.

3. Connect phone to your router wifi network.

4. Login “iCSee” app, click the “+”in the upper right corner, and click “more” in the upper right corner.

5. click “Add the camera on same router.

6. Enter search device interface, click searched camera to add device,device will show in the device’s list, which represent device connect successfully.

7. Click it to view the monitoring image, also can do the relevant operation and setting

Manual configuration: AP netless direct connection mode

When there is no network in the installation environment, please select the following pairing method;

 1. Long press the camera Reset button for 10 seconds to restore the device to factory settings .

2. Short press the camera Reset button 2-5 to enter the direct connection mode (most devices will voice prompt “enter direct connection mode”).

3. Open the mobile phone desktop-settings-wireless network, search for the device wireless hotspot name, Enter the wireless password:1234567890, connect to the wireless hotspot of the device;

Indoor IP Camera hot spot name: robot_xxxx;

Other kind of camera hot spot names: camera_xxxx;

Tips:

AP hotspot mode is only used for installation when there is no network in the environment, and cannot be remotely monitored,can only be accessed within 10 meters of the establishment of the hotspot!

4. Open the ‘iCSee’ APP, and directly add the device in the local direct connection mode.

5. The device is displayed on the device list interface, which means that the device is successfully connected.

6. Click the ‘Play’ button to enter the monitoring screen and perform related operations and settings.

7. If you have already registered an account to log in, please click the “+” sign at the top right, and click the “AP direct connection” mode to add.

How to set up mobile tracking？

Note: Mobile tracking and smart humanoid alert can’t be used at the same time;

●Click the “Mobile Tracking” switch buttonin the preview interface to turn on the corresponding function;

●Motion tracking: when it’s on, as long as an object enters the camera’s illumination range, camera will track the moving trajectory;

●Watch Point: set a fixed position, when the camera is operating or tracking, it will automatically return to the set position after staying for a period of time;

How to set the dual-ligh tal ert mode Star light full color？

Note: Mobile tracking and smart humanoid alert can’t be used at the same time;

Open the ‘iCSee’, click the ‘real-time playback’ , click or slide to the “light” or the “bulb” icon in the screen to open the setting screen;

●Night colored lights：When the light is insufficient, the white light will start, and the image will be colorful;

●Infrared night vision： When the light is insufficient, the infrared light is activated and the image becomes black and white;

●Double light alert：When the light is insufficient, the infrared light will be activated. When someone enters the monitoring screen, the white light will be triggered and the image will be colorful.
After a few seconds when the person walks away, the infrared mode will be switched on and the image will become black and white;

How to s et the humanoid alert function?

Note: Mobile tracking and smart humanoid alert can’t be used at the same time;

Open the ‘iCSee’, click the device real-time playback, click on the upper right button ‘setting’ ，Enter the ‘settings’-smart alarm, open the interface to make related settings.

Function introduction:

 
●Notification: Must be turned on to receive alarm trigger information.

●Humanoid detection: only judge and detect people to trigger an alarm;

●Show Tracking: When the human figure appears on the screen, the human figure can be tracked and reminded; Rule setting: select the designated area [Warning Line], when someone enters the divided area, the alarm can be triggered;

Add shared device

1. Click “Share” in the device list to pop up the QR code page using the main phone.

2. Log in to the ‘iCSee’ APP with the mobile phone you want to share,
click the “+” sign in the upper right corner of the APP main interface, click “Scan QR code to add a camera” , scan the QR code of the device shared by others or input Add the device serial number (the shared device must be connected to the Internet and successfully
added to the APP).

How to Restore factory settings/AP hotspot switching？

1. Long press the camera ‘Reset ‘ button for 10 seconds, and you can let go when you hear ‘ Restore factory setting,please wait’.

2. Short press the camera Reset button 2-5 to enter the direct connection mode (most devices will voice prompt “enter direct connection mode”).

How to query device serial number and info?

1. Open the ‘iCSee’, enter the real-time playback of the device, click on the upper right setting to enter the setting center-about the device , the QR code can be directly scanned and shared with other family members to watch (the QR code valid time is 30 Minutes); if exceeded, it will automatically expire;

2. If you find that the device time is not synchronized, please click the device time to synchronize it;

HOW TO USE THE CAMERA?

1.Please open the software to register one and log in to your account if you do not have an account.

2.Click “+” > Set up “MY DEVICE” to WiFi

3.Enter your WiFi password. Then click “confifirm” and wait for the camera to connect it.

Notes

* Please reset the device if the camera does not have any voice reminders for more than 180 seconds.

* Please check the WiFi password again and make sure the WiFi channel is 2.4GHz.

* Please do not make the device too far away from the Router.

4.Upon a successful connection, you can set up the name and the password of the camera.

SHARE THE CAMERA：

1.The administrator can send the QR code and password of the camera to the other persons.

2.Scan the QR code by the administrator to share with you and add the camera.

Infographics

.

<p>The post How To Use Icsee Camera 2024 first appeared on NVR IPCAMERA SECURITY.</p>

How To Enable IP Camera Offline, Analog Camera Disconnection Notification Alerts

One of the most important features of any security system is its ability to alert you when something goes wrong. Whether it’s an IP camera offline or an analog camera that stopped working, a storage failure, or any other exception, you want to know about it as soon as possible. That’s why Camius DVR and NVR camera systems offer various options for setting up alerts or notifications for different events. While cheap IP and analog CCTV camera systems often lack this feature, Camius provides this advanced functionality, setting it apart from other systems.

Exception Settings in Camius NVR and DVR camera systems

Camius NVRs have ‘Exception’ settings under Setup >> Alarm >> Exception, where you can choose the alarm type. These include:

This is an example of the NVR’s local user interface menu while the recorder is connected to the monitor

Local User Interface and Web Browser Interface

The settings can be accessed through two interfaces:

This is an example of the menu while you access the Camius DVR or NVR recorder using a web browser

Push Notifications alerting about wireless or wired analog / IP camera offline on Camius View App

In addition to the settings on your Camius Security Camera DVR or NVR Network Video Recorder, you can also set up push notifications on your Camius View app. These notifications include Video Loss alarm and HDD alarm. To do this, you’ll first need to add the NVR to your app (follow this guide about adding the Camius DVR or NVR to the Camius View app).

Once the NVR is added, you can select the types of push notifications you want to receive directly from the app.

Push Notifications related to Storage (HDD or Micro SD card) installed to the Camius camera system)

Push Notifications related to the IP or Analog or Wireless Camera Disconnection

Read Also : LaView NVR Setup and User Guide

Regular maintenance can prevent issues like a CCTV camera disconnected, ensuring continuous surveillance.

Regular maintenance can prevent issues like a CCTV camera disconnected, ensuring continuous surveillance. However, sometimes problems may arise that affect the connection of your security cameras. In such cases, you need to troubleshoot the issue and find the cause of the disconnection. Depending on the type of camera system you have, the steps may vary. For analog security camera systems, you need to check the power supply, the cabling, and the DVR settings. For wired PoE power over ethernet camera systems, you need to check the network connection, the IP address, and the NVR settings. To learn more about how to troubleshoot these issues, you can refer to the following guides:

How to Setup DDNS on Camius DVR and NVR Surveillance Recorder?

To setup DDNS for Camius security cameras, you’ll first need to register for a DDNS service, obtain a domain name, activate DDNS in your camera’s network settings, and then input your DDNS account’s hostname, username, and password.

If you want to access your Camius DVR or NVR recorder remotely from your PC, you might encounter some difficulties with dynamic IP addresses. A dynamic IP address is one that changes every time you connect to the internet, making it hard to establish a stable connection with your recorder. That’s where DDNS comes in handy.

What is DDNS?

Dynamic DNS, or DDNS, stands for Dynamic Domain Name System, and it allows you to assign a static domain name to your recorder, regardless of its IP address. This way, you can always connect to your recorder using the same URL without worrying about IP changes.

Dynamic DNS lets you access your Camius security camera device on the internet with an easy-to-remember web address like “camiusnvr.dyndns.com” instead of a hard-to-remember IP address like 216.144.47.245. This is useful when you want to connect to your security camera, DVR, NVR from anywhere in the world.

Setting up DDNS

In this guide, we will take you through the steps of setting up DDNS on your Camius DVR or NVR recorder. You will need to have an account with a DDNS service provider, such as DDNS_3322, DYNDNS, NO_IP, CHANGEIP, or DNSEXIT.

Step 1:

Create an account on your preferred DDNS service provider website and a domain name (which is a hostname for your Camius DVR/NVR or an IP camera). Each of these providers offers free and paid accounts, which you need to select based on your requirements.

You will need to provide your email address and create a password. After verifying your email, you will be able to log in to your dashboard. The process of creating an account with DDNS service providers is similar.

Create a domain name for your recorder on the DDNS server. You can usually choose any domain name (hostname) you like, as long as it is not already taken. For example, you can use something like camius.no-ip.org or camius2023.dyndns.com

Step 2:

Configure DDNS settings on your Camius DVR or NVR recorder.

Step 3:

Step 4:

Enter the Domain name (hostname) in a web browser tab bar to access your Camius DVR/NVR remotely from a PC or Mac. Enjoy!

How do I backup NVR or DVR settings?

You can export the main menu settings you have configured to a USB flash drive, or import an exported setting file from USB flash drive to the NVR.

Camius user interface menu for reference to backup NVR, DVR configuration

Camius IPVAULT2256PR menu (16 Channel NVR)

Camius TRIVAULT4K2168R menu (16 Channel Hybrid DVR)

Camius IPVault1128PR menu (8 Channel NVR)

Camius IPVault1128PR menu (8 Channel NVR)

.

Camius Hybrid DVR Camera Systems are in high demand by Gas Stations and Retail Stores

Security and surveillance are paramount today, especially for businesses like gas stations and retail stores. The demand for advanced surveillance solutions has risen with the increasing need to protect assets, employees, and customers. Camius, a renowned provider of security systems, introduces its innovative Hybrid DVRs, a perfect solution for enhancing security in gasoline pumps and retail stores. This article explores the numerous advantages and unique features of Camius Hybrid DVR camera recorders that make them stand out in the market.

1. Gas Stations, Retail stores upgrade to Camius 4K security at minimal cost

One of the major benefits of choosing Camius DVR camera systems is their cost-effectiveness. Camius innovative 8 and 16-channel DVR recorders significantly reduce the cost of upgrading surveillance systems by eliminating the need for new wiring. Business owners can retain their existing coaxial wiring infrastructure and only replace the DVR recorder and cameras when necessary.

Traditional camera upgrades often entail the labor-intensive process of rewiring the entire premises, which can be time-consuming and expensive. With Camius DVR camera systems, this hassle is eliminated. The compatibility with existing coaxial wiring not only saves costs on new cabling but also reduces the installation time, causing minimal disruption to the business operations during the upgrade process.

Moreover, reusing the same wiring infrastructure does not compromise the system’s performance or reliability. Camius DVRs are designed to seamlessly integrate with the existing coaxial cables, ensuring smooth transmission of high-definition video and data without any loss in quality.

By opting for Camius DVR camera systems, business owners can enjoy cutting-edge surveillance technology without breaking the bank. The ability to upgrade to the latest DVR recorder and cameras as needed while keeping the existing wiring makes Camius an economical and future-proof choice for filling stations and retail stores.

In conclusion, Camius Hybrid DVRs offer various benefits, including reduced upgrade costs, compatibility with existing wiring, and ease of installation. Business owners can enhance their security measures without a significant financial burden and rest assured knowing they have invested in a reliable, advanced, and cost-effective surveillance solution.

2. The Power of Hybrid DVRs

2.1 What are Hybrid DVRs?

Hybrid DVRs combine the capabilities of traditional Digital Video Recorders (DVRs) and Network Video Recorders (NVRs). They allow users to utilize both analog and IP cameras, providing flexibility and compatibility with existing systems.

12 Channel Hybrid DVR camera recorders

24 Channel Hybrid DVR camera recorders

2.2 The Advantages of Hybrid Technology

Camius Hybrid DVRs offer businesses the best of both worlds. By supporting analog and IP cameras, they enable a seamless transition from analog to IP surveillance, protecting previous investments while embracing modern technologies.

3. Ultra High Definition Surveillance

3.1 Crystal Clear Resolution

Camius Hybrid DVRs support high-definition cameras, capturing clear and detailed images. This level of resolution is crucial for identifying faces, license plates, and other critical details in businesses.

3.2 4K Ultra HD Recording

With 4K Ultra HD recording capabilities, Camius surveillance DVR camera reocrders ensure that every inch of the surveillance area is captured in astonishing clarity, leaving no room for ambiguity or doubt.

4. Intelligent Video Analytics

4.1 Smart Motion Detection

Camius Hybrid DVRs are equipped with intelligent video analytics, including smart motion detection. This feature lets the system detect and alert users of unusual activities, such as unauthorized access, loitering, or suspicious movements. Only with Camius DVR records can you detect video motion, vehicles, and pedestrians! You can also set multiple motion detection areas for analog and IP cameras.

Web browser view

4.2 Advanced AI Technology

Integrating advanced AI technology empowers these DVRs to recognize specific objects, track movements, and even provide heat mapping to identify high-traffic areas in commercial locations.

AI functions with Analog and Camius IP cameras (TRIVAULT4K2168R)

5. Remote Access and Mobile Monitoring

5.1 Stay Connected Anywhere, Anytime

Camius Hybrid DVRs offer remote access capabilities, enabling business owners and managers to monitor their business premises using smartphones, tablets, or computers from anywhere in the world. Whether you have a Windows PC, Apple Mac or iPhone, iPad, Android smartphone, or tablet, the DVR is compatible!

5.2 Real-time Alerts on the Go

With mobile monitoring, users receive real-time email alerts and push notifications on their devices, ensuring prompt actions can be taken in case of emergencies or security breaches.

6. Enhanced Storage Options

6.1 Efficient Data Storage

Camius Hybrid DVRs support various storage options, including 3.5″ SATA HDD, 2.5″ SSD, and even Cloud storage, ensuring ample space to retain crucial surveillance footage for extended periods.

Camius Hybrid DVR camera recorders work with Dropbox and Google Drive. Click HERE for more information.

6.2 Scheduled Backup and Archiving

The DVRs allow users to schedule automated backups and archiving, providing an additional layer of data protection and seamless storage management.

7. DVR Recorder with User-Friendly Interface

7.1 Easy Setup and Configuration

Camius Hybrid digital video recorders boast a user-friendly interface, simplifying the setup and configuration process. Business owners can quickly deploy the system without requiring extensive technical expertise.

CLICK HERE for the DVR installation guide

7.2 6.2 Intuitive Control

The intuitive control panel and mobile app make it effortless for users to navigate through various features and access the necessary information promptly.

8. Conclusion

Camius Hybrid DVRs have proven to be a game-changer for businesses, offering a perfect security solution with their hybrid capabilities, high-definition surveillance, intelligent video analytics, remote access, and user-friendly interface. By choosing Camius Hybrid DVRs, businesses can ensure comprehensive security, loss prevention, and a safer environment for customers and employees alike.

FAQs

1. Are Camius Hybrid DVR camera recorders compatible with existing security camera systems?

Yes, Camius Hybrid DVR recorders are designed to be compatible with both analog CVBS, AHD, CVI and TVI  and IP Onvif conformant cameras, making them an ideal choice for businesses looking to upgrade their security systems without discarding existing cameras.

2. How can I access the recorded footage remotely?

You can access the recorded footage remotely through Camius’ user-friendly mobile app or Camius DVR software. Simply install the app on your smartphone or tablet, and you can monitor your gas pumps and retail stores from anywhere with an internet connection.

3. What is the storage capacity of Camius Hybrid DVRs?

Camius Hybrid DVRs support various storage options, including HDD, SSD, and Cloud storage. The capacity can be chosen based on the business’s needs and the required retention period for surveillance footage. CLICK HERE for the list of compatible hard drives

4. How reliable are Camius Hybrid DVRs in terms of data protection?

Camius analog DVR camera recorders come with advanced data protection features, including scheduled backup and archiving. These ensure that your surveillance footage is securely stored and protected from data loss or tampering.

How to use 2 way audio security cameras?

The feature of two way audio security cameras empowers users to both receive and transmit audio through their IP camera, adding an extra layer of interactivity and communication to the security setup.

Camius presents its cutting-edge 4K spotlight PoE cameras that come equipped with built-in high-quality microphones and speakers, eliminating the need for external attachments to enable the two-way audio function. For optimal performance, it is recommended to install Camius PoE cameras alongside Camius PoE or Non PoE NVR recorders or Hybrid DVRs.

 .

The latest R series NVR and DVR recorders facilitate seamless control of Camius spotlight cameras, microphones, and speaker volumes directly from the NVR settings. Additionally, users can conveniently modify the audio encoding format per their requirements. To troubleshoot two-way audio, turn down the input volume and output volume and test switching audio code type (G711A and G711U).

Two factors can affect the audio quality: network and distance.

The recommended distance for the microphone to transmit quality sound is 9.5 to 16 feet.

To engage in two-way audio communication, the Camius View app is the go-to platform.

Here’s a simple guide to using the 2 way audio security cameras feature:

It’s important to note that the two-way audio experience with Camius security cameras is characterized by live bidirectional communication and not an intercom-type function.

In most scenarios, the mute function is enabled by default. By enabling audio, users can record audio from the microphone of their security camera. To listen to the recorded audio, whether in live mode or during playback, it is necessary to open the individual channel in full screen on which the audio-enabled security camera is operating. This applies to both NVR and app usage.

However, it’s crucial to exercise caution while utilizing surveillance audio, as its usage might be restricted or subject to regulations depending on the location. Always ensure to verify with local authorities on the proper and legal use of security cameras with audio to avoid infringing upon privacy laws. Unauthorized audio recording can be considered illegal in certain jurisdictions. Hence, Camius emphasizes the significance of complying with local laws and assumes no liability for the misuse of its surveillance cameras that do not align with the respective regulations.

The Impact of Artificial Intelligence in IP Cameras: Why Camius Stands Out

In recent years, the integration of artificial intelligence (AI) has revolutionized various industries, and the field of IP cameras and other security systems is no exception. AI-powered IP camera systems have significantly enhanced surveillance capabilities, enabling advanced analytics, real-time monitoring, and improved security. Among the leading players in this field, Camius stands out as a pioneering brand that has embraced AI technology to deliver exceptional performance and innovation. In this article, we will explore the applications of AI in IP camera systems and why Camius has become a prominent name in this industry.

The Role of Artificial Intelligence in Security Camera System

Artificial intelligence has transformed IP camera systems by providing advanced functionalities and intelligent features that greatly enhance their effectiveness. Here are some critical applications of AI in IP camera systems:

Why Camius Stands Out

Among the various brands in the IP camera industry, Camius has emerged as a frontrunner in implementing AI technology into their camera systems. Here are some reasons why Camius stands out:

Artificial intelligence has revolutionized the IP camera industry, enabling advanced analytics, real-time monitoring, and enhanced security. Camius has distinguished itself within this landscape by harnessing AI technology to deliver cutting-edge IP camera systems. Through its robust AI algorithms, customizable solutions, real-time insights, scalability, and user-friendly interfaces, Camius has established itself as a prominent player in the field. As AI continues to evolve, Camius remains committed to pushing the boundaries of innovation.

<p>The post Camius Devices FAQs and How-Tos first appeared on NVR IPCAMERA SECURITY.</p>

.

Hikvision is one of the world’s largest video surveillance manufacturers and a leading brand in the video surveillance industry. Their top-of-the-line IoT solutions and video security systems set them apart from other DVR brands.

However, since all recorded videos get stored on the DVR’s hard drive, they might get accidentally deleted or lost. Losing CCTV footage can have potentially disastrous consequences if there’s some important information on the deleted or corrupted videos.

But don’t start worrying just yet. If you find yourself in such a situation, go through our detailed guide on how to recover deleted videos from the Hikvision CCTV system or DVR without any complications.

.

Can You Recover Deleted Hikvision DVR Recordings?

Yes, using data recovery software, you can restore deleted Hikvision CCTV footage from different data storages like a hard drive, SSD, or Hikvision SD cards.

There are several available methods to assist users with recovering deleted videos. But before we dive into recovering corrupted or deleted videos from Hikvision CCTV systems, we must understand the various possible reasons for data loss and the corresponding solutions for data recovery.

To avoid significant data loss from the DVR due to unforeseen issues, make sure that you back up video recordings periodically.

How to Recover Permanently Deleted Hikvision DVR CCTV Footage

.

Before we look at ways to repair corrupted Hikvision DVR data storage, let’s go through what you can do to recover your data beforehand. Some methods used to perform hard drive data recovery can result in the deletion of your existing data. Thus, you must first retrieve your lost Hikvision DVR recordings.

.

Perhaps the best way to restore deleted Hikvision CCTV footage is to use trustworthy video recovery software. While several data recovery tools are available on the market, Disk Drill is one of the best data recovery apps.

✅

Disk Drill is a trustworthy DVR data recovery software with an impressive track record for successful recoveries, and it supports over 300 file types. While Disk Drill can retrieve deleted or lost video files in the MP4 format supported by Hikvision surveillance videos, it also supports other video formats such as AVI, FLV (Flash video), M4V (iTunes video), MPG (MPEG video), WMV (Windows Media Video). Moreover, the software is available on all major file systems – Windows, Mac, and Linux.

Disk Drill also comes packed with advanced features like S.M.A.R.T. disk Monitoring (hard drive health checks) and byte-to-byte level backups that can be useful in retrieving data from corrupt hard drives. Here’s a detailed guide on how to recover deleted or corrupted videos from Hikvision CCTV using Disk Drill:

1.Before you begin the recovery process, unmount the Hikvision DVR hard drive.

2.Download and Install Disk Drill.

3.Connect the unmounted hard drive to your computer or PC directly or via an adapter.

4.Launch Disk Drill on your computer. Now, select the hard drive from the list of devices your computer can access. While Disk Drill selects the All Recovery Methods option by default, you also choose from other recovery methods – Quick Scan or Deep Scan.

5.Click Search for Lost Data. Disk Drill’s advanced algorithm will scan through data storage for your deleted Hikvision CCTV recordings. The software also allows you to pause, save or resume the scan whenever you want.

.

6.Once the scan is complete, you can filter through the results. Now, click Review Found Files. Disk Drill allows you to preview the files you want to get back and even recover up to 500 MB of data for free!

7.Once you’ve selected the videos you wish to restore from the Hikvision DVR hard drive, click the Recover button.

👀

You can also use the filter option to quickly locate your CCTV recordings. For instance, key in “mp4” into the top right hand corner field box and hit Enter.

8.Type in the recovery location and ensure you’re restoring your files to a different device from which you’ve just recovered data. Finally, click Ok.

🔗

You can also use these steps to recover deleted or lost videos from other devices, such as video cameras or deleted dash cam footage. To learn more about Disk Drill and all its premium features, you can go through our comprehensive Disk Drill review.

How to Fix Corrupted Hikvision DVR Data Storage

After successfully retrieving lost Hikvision DVR recordings, you can attempt to fix corrupted Hikvision DVR data storage. Follow our step-by-step guide to repair the hard drive without any hassles.

Method 1. Repair Partition Using TestDisk

TestDisk is a powerful, open-source data recovery tool primarily designed to recover lost partitions, fix partition tables and rebuild the boot sector. It’s available for free and can run on all major operating systems. Once you’ve recovered your deleted videos, you can attempt to repair the corrupted Hikvision DVR hard drive using TestDisk.

.

Interesting Read: How To Face Detection &#8211; Face Recognition

Here’s how you can repair partition using TestDisk:

1.Download and unzip the TestDisk folder. In our case, the folder was named “testdisk-7.1.win”.

2.Right-click testdisk_win and click Run as administrator.

3.Use the arrow keys to select the No Log option, then hit Enter. You can also click Create to create a log if you like, append info to an existing one, or not create one at all.

4.Now, select the Hikvision DVR hard drive and press Enter.

5.Select the partition table type. For Windows users, select Intel. Now, press Enter.

6.Next, select the Analyse option and hit Enter. On the next screen, click Quick Search to begin the partition recovery process.

7.After the scan is complete, the missing partition will appear on the screen. Select the partition you wish to recover and follow the prompts on the screen. Move to the Write option and press Enter.

8.Press Y to write the partition table and press Enter again.

To know more about the pros and cons of using TestDisk to recover data and partition recovery, look at our in-depth TestDisk review.

Method 2. Scan Your Drive Using CMD (chkdsk)

The CheckDisk utility (chkdsk) is an in-built command in Windows that can scan and resolve any problems it discovers on your hard drive. If bad sectors or errors on your Hikvision DVR disk have caused data to be deleted or overwritten, they can be repaired using the CMD prompt.

Here’s how you can scan and fix the DVR hard drive with the CheckDisk utility:

1.Go to the Start menu and type in cmd. Now, select the Run as administrator option.

2.Once the Command Prompt window opens, run the following command: chkdsk F: /r (Remember to replace F with the drive letter assigned to your hard drive).

👀

Here, we’ve used the /r parameter. It fixes any errors on the disk and searches for bad sectors.

.

FAQs

.

How to recover overwritten CCTV footage from Hikvision DVR?

.

Here’s how you can recover overwritten CCTV footage from Hikvision DVR:

.

.

What is the best DVR data recovery software?

.

While several data recovery tools are available on the market, Disk Drill is the best DVR data recovery software. It supports the MP4 format supported by Hikvision CCTV footage and other video formats such as AVI, FLV (Flash video), M4V (iTunes video), MPG (MPEG video), WMV (Windows Media Video). Moreover, the software is available on all major file systems – Windows, Mac, and Linux.

.

.

Can you recover deleted CCTV footage for free?

.

There are certain data recovery software that offer free recovery. For instance, Disk Drill allows you to recover up to 500 MB of CCTV footage for free. If you need to recover more data, check out software like PhotoRec and Recuva

.

.

Does CCTV footage get deleted automatically?

.

It depends on the DVR settings and the capacity of your hard drive. In some cases, old CCTV footage may be deleted periodically, i.e., after a month or a week. In other instances, CCTV recordings may get deleted or overwritten due to a lack of space.

.

Conclusion

The videos and recordings from CCTV surveillance systems often hold essential security information. The methods outlined in this article should answer all your questions on recovering lost or deleted CCTV footage from Hikvision DVR hard drive.

You can use these techniques to retrieve surveillance videos from any Hikvision CCTV camera model and even repair the corrupted DVR hard drive for future use.

<p>The post How to Recover Deleted CCTV Footage From Hikvision DVR first appeared on NVR IPCAMERA SECURITY.</p>

The following Swann Security cameras can only be viewed and accessed via the Swann Security app from a mobile device.

They cannot be added to Swann security system recorders, such as DVRs, NVRs, and NVWs. These recorders are compatible with specific system camera models.

Can a SWIFI camera work without Internet?

Internet is required as the SWIFI cameras communicate to the P2P server using the Internet to stream to the Swann Security app and upload recordings to the cloud.

Compatible Routers

Any of the following routers are compatible provided they have a 2.4 GHz frequency:

For more information, see What router WiFi frequency band is my SWIFI camera compatible with: 2.4GHz VS 5GHz Frequency?

Compatible Wi-Fi extender or repeaters

It is possible for the SWIFI camera to pair to the router via WiFi extender if the extender is compatible and setup correctly to the router. Troubleshooting and configuration of your extender’s settings have to be performed by your router manufacturer support team, Internet Service Provider or your IT department. See this article: How to boost your WiFi signal and extend WiFi range.

Tip: Try to pair the camera to the router first to check whether its internal network adapter is working. If it works via router but not extender, then there’s a chance the extender is not compatible.

Swann Wi-Fi camera FAQs

Read More : Swann Security Troubleshooting All Devices

Not Compatible / Not Recommended

We do not recommend SWIFI cameras to be connected to the following devices because they cannot provide the necessary network configuration information to the camera to allow it to join the network automatically unless your network device is configured. Troubleshooting and configuration of your device’s settings have to be performed by your router manufacturer support team, Internet Service Provider or your IT department.

Can I view my SWIFI camera on a TV / computer or record to a DVR / NVR?

The cameras above are hub-free. A hub is a base station or recording/storage device that connects via the Internet to the cameras. In contrast, a hub-free camera operates on Wi-Fi exclusively without requiring any additional hardware to store footage. 

A hub-free (standalone) Wi-Fi camera is only capable of:

These features make a hub-free Wi-Fi camera suitable for users who prefer a wireless setup, easier DIY installation, less hardware, and less footage to check in low-traffic areas of view. 

Accessing live view, recordings, and other settings are covered in the manuals below for your device: 

How do I tell whether my router’s WiFi signal is 2.4GHz or 5GHz for pairing a SWIFI camera?

This is one of the most common reasons why a connection will fail while trying to pair a SWIFI camera to your Swann Security account. If you try to pair a SWIFI camera to the incorrect frequency or SSID name, the error that appears on the app can be one of the following:

Via Mobile Device Settings

One way to tell if the phone is connected to the correct frequency of the router is by checking the name of the SSID (the default name of your router’s WiFi hotspot): 

In the example above, the router has multiple SSIDs. An SSID that has “_2.4GHz,” “24G,” “2.4,” or “24” appended at the end is most likely a 2.4GHz signal. This is the network your phone needs to be connected to before you start pairing a SWIFI camera. 

To avoid connecting to a 5GHz SSID, see How to forget 5GHz connection for pairing a SWIFI camera.

Via Router GUI

If you see two or more Wi-Fi network names that belong to you without 24 or 5, then one may be a 5 GHz band. To identify which name uses 2.4 GHz or 5 GHz, login to your router’s settings. 

For assistance with accessing or navigating your router, contact the manufacturer of your router or your Internet Service Provider if you do not know. Swann Tech Support can only assist in pairing IF your router has a 2.4GHz signal and if you already know the correct WiFi credentials of your router.

How to change the time zone of my SWIFI camera in the Swann Security app?

The error “Device Timezone Out of Sync” appears if your camera’s time zone is different from your phone app’s time zone. 

If your camera is in a different location (with different time zone) than your mobile device, you can ignore hit Cancel. 

If the date and time displayed on the camera’s Live View is incorrect, do the following: 

Repeat each step for each camera device paired to your Swann Security account.

How to create Guest account on a WHD-PTCAM using SwannView Link software?

Installing SwannView Link

Adding the camera

Since the computer is on the same router or modem already, when you open SwannView Link the camera will be auto-detected, but the password will not be entered yet. You will see the error message below. Just click on OK.

How to forget 5GHz connection for pairing a SWIFI camera

Some mobile devices have a tendency to switch between hotspots or SSID automatically. This can disrupt the pairing process when setting up your SWIFI camera to your mobile device. 

To avoid connecting to a 5GHz signal or the wrong hotspot during pairing, forget the 5GHz connection: