How do I integrate Hanwha IP cameras and SUNAPI with Immix?

Summary

This article details the steps to integrate Hanwha IP cameras and SUNAPI with Immix.

Integrate Hanwha with Immix

To begin the integration, a suitable port for Immix must be located.

NOTE: These are default ports only (they can be configured and may be
different to what is listed).

To find ports in Immix:

Configuring Users in Hanwha Vision for Immix

To configure users:

Video Profile

The integration has capabilities to switch between different video profiles. To switch between profiles:

Configuring a Hanwha IPC SMTP Alarm

To configure the alarm into Immix:

S# – represents the ServerID.
A# – represents the Input of Response.
E# – represents the Event Number associated with the Server Type,
e21 is defaulted to IPC Object Detection.

IPC Email Example

Subject: ObjectDetected

Sendor: S29.a1.e21@ImmixAlarms.com To: S29.a1.e21@ImmixAlarms.com

Date: 20240514-12:03:47XMailer:NFMail

https://support.immixprotect.com/hc/en-us/articles/25738891242395-Hanwha-IP-Camera-SUNAPI-Integration 4/7
XMailer: NF Mail MIME-Version: 1.0 Content-Type: multipart/mixed; boundary=594786580.1111.samsungipolis.com –594786580.1111.samsungipolis.com Content-Type: text/plain; charset=”iso-8859-1″ Content-Transfer-Encoding: 7bit ObjectDetected Time : 20240514-12:03:47 Camera IP : 192.168.1.166 Event Type : EventRule_5_CH1 –594786580.1111.samsungipolis.com Content-Type: application/octet-stream; Content-Transfer-Encoding: base64 Content-Disposition: attachment; /9j/4AAQSkZJRgABAQEAYABgAAD/2wBDABQODxIPDRQSEBIXFRQYHjIhHhwcHj0s LiQySUBMS0dARkVQWnNiUFVtVkVGZIhlbXd7gYKBTmCNl4x9lnN+gXz/2wBDARU

Enabling Digest Auth

If you are having trouble using GetConfig, enable Digest Auth for your Hanwha user.

The image below shows where to enable this:

NOTE: Ensure that the user is Admin or Full user permissions. You must
create an Immix user and assign them as an administrator. A default
admin account cannot be used.

Configuring a Hanwha IPC SMTP Event

To configure the system-based events into Immix:

Obtaining the S Number

To obtain the S number:

Configuring Devices within Immix

To configure a device within Immix:

Obtaining the ID of a Camera for Use in the Extra Value

To obtain the ID of the camera:

SSL Error Alarms

By default, the alarm receiver is configured to disallow insecure connections. To allow connections to insecure devices (no SSL, invalid cert, etc.), change the RequireCertificate config key in appsettings.json to false.

Alarms Not Decoding

By default the alarm JSON messages are saved in the file store in the same folder as any alarm footage. To diagnose decoding issues, confirm that this message is what is expected. A typical alarm message looks like the following snippet. Alarm messages always have the broadcastAction alarm.

{
“Tran”: {
“Command”: “broadcastAction”,
“Params”: {
“Params”: “eyJhY3Rpb25JZCI6InthYWNiMjdmOC1lYTcwLTRlOGEtOGE1YS03YjZiNzk5ZTliMGR9IiwiYWRkaXRpb25hbFJlc291cmNlcyI6WyJ7MDAwMDAwM
“RuntimeParams”: “eyJkZXNjcmlwdGlvbiI6Il90aHVtYl9kb3duIiwiZXZlbnRSZXNvdXJjZUlkIjoie2RhZWU5ZWIyLTEyZDYtZTUwNy00Y2MxLWM4ZmUxNG
}
}
}

A second approach is to review the service logs, as all messages (even non-alarm messages) are logged there.

How to use Wisenet cameras with exacqVision

Summary:

This article provides information on using Wisenet cameras with exacqVision.

Step By Step Guide:

Wisenet Camera Settings

Mandatory

The following settings are mandatory:

Optional

The following settings are optional:

After Adding to exacqVision

exacqVision defaults to using the Hanwha default H.264 stream (profile 2) but can be changed to H.265. This changes exacqVision to utilize the default H.265 stream on the camera (profile3).

NOTE: It is not possible to set h.265 via exacqVision on a fisheye camera.
You need to log in to the camera interface and manually change the FISHEYE
profile to H.265.

To change the default stream to H.265:

1.Navigate to the exacqVision Camera Settings page and click the Recording tab.
In the Rate Control field, the default is Constant Quality which equates to Variable Bit Rate in Hanwha cameras.

The Quality slider default of 2 sets a low cap.
1 = minimum VBR cap for that stream
10 = maximum VBR cap for that stream
For 4MP+ resolution cameras it is beneficial to increase the quality to 3 or 4; otherwise, the video may be compressed too much thus decreasing quality.

2.If needed, select a stream to add from the Multistreaming dropdown menu and click Add Stream.

NOTE: With high-resolution cameras, it is best practice to create lower
resolution live viewing streams to save on decoding and bandwidth. These
streams can be added in exacqVision on the Camera Settings page.

3.Click the Motion tab to edit motion on the camera (although exacqVision does not have all the options available that are in the Hanwha cameras).

NOTE: It is possible to add motion, including windows, without adding\
multiple points to create unique shapes.

4.Click the Analytics tab to see several options for displaying and recording data.

5.If the camera is a fisheye, click the Digital PTZ/Fisheye tab to configure the proper dewarp code.
a. Select Immervision from the first dropdown menu.

b. Select the proper code from the second dropdown menu.

Refer to the following article for Hanwha Fisheye Lens Codes: Immervision Fisheye Dewarp Lens Codes

c. Select how the camera is mounted for proper dewarping from the third dropdown menu.

NOTE: Many of Hanwha’s fisheye cameras can use additional camera side dewarp
channels. These should be created first before the camera is added to
exacqVision, so they are identified and configurable inside of exacqVision.
These channels have no motion detection so they either need to record 24/7
or be used for live video only.

NOTE: The Video tab does not exactly match what is in the camera.

Brightness = Brightness
Contrast = Contrast
Saturation = Color Level in the camera
Wide Dynamic Range = controls SSDR in the camera
Video Mask = controls the camera’s Privacy Areas

Searching AI Metadata

To search AI metadata:

1.From the exacqVision home page, click the Search () icon in the top left corner of the screen.

2.Expand the camera tree then select the camera and the analytic metadata associated with it.

3.Select the Search Range to search for then click Search.

4.Click the Paper () icon to view the raw metadata.

A pane to the right of the video will appear with the raw data of that time.

5.Check the Show Filters checkbox to filter data.

6.In the pane to the left of the video, check the checkboxes to filter.

7. Click Save then click the Search button again.

NOTE: Save filters can be selected from the dropdown menu at the top.

8.If certain overlays for the metadata need to be hidden, click the Green () icon and select which overlays should be hidden.

Creating Events Based on Analytics

NOTE: The analytics must be configured in the camera first. Once done and the
camera is added to exacqVision, disable and re-enable the camera.

To create events based on analytics:

Monitoring Analytic Events

To monitor analytic events, follow the steps in the Creating Events Based on Analytics section. However, use Event Monitoring instead of Event Linking.

Special Considerations

Take the following into consideration when setting up a camera:

Optional Common Camera Settings

The following camera settings are optional:

Verint recorders using different FPS for normal and event recording

Summary:

When a Hanwha camera is registered to a Verint NVR, the use of different FPS can be engaged on the NVR

Explanation of Behavior:

Resolution:

• Firmware can be easily updated via the NVRs web interface, the NVRs monitor/mouse interface, Wisenet Device Manager, or Wisenet Viewer. The process takes approximately 5 minutes.

• The way Verint operates is that the recorder will dictate the camera’s FPS, and changing the video profile on the camera, by default, momentarily drops and reestablishs the connections.

How to add a Wisenet camera to Genetec Security Center 5.9

Summary:

This article provides instructions for adding a Wisenet camera to Genetec Security Center 5.9 and the additional steps needed if the camera has a fisheye lens.

Step By Step Guide:

To add a Wisenet camera to Genetec Security Center 5.9:

1.Open Wisenet Device Manager.

2.Double-click your camera to load the camera’s webpage.

3.Enter and confirm your new password, then click Apply.

NOTE: If a password has already been configured and you need to default
the camera, press and hold the Reset button for 5-10 seconds.

.

4.From the Genetec Config Tool application, click the Video icon.

5.Right-click Archiver and select Unit enrolment.

6.Click Manual add then select Hanwha Techwin from the Manufacturer dropdown menu, select Wisenet from the Product type dropdown menu, and enter the IP address of the camera.

NOTE: You can find the IP address of the camera in the Wisenet Device
Manager results screen. Click Add and close to enroll the camera.

TIP: If you see a Bad logon error, move your mouse over the text and an Add button will appear.

Enter the username and password of the camera then click the Add button.

After a few moments the status should change to Added.

.

NOTE: Sometimes the status in Genetec sticks on Bad logon. To resolve this
issue, click Clear All at the bottom of Unit enrollment and add the camera
again. The camera has now been added to Genetec Security Center 5.9.

Configuring a Fisheye Camera

The following additional steps are required if the camera has a fisheye lens:

1.From the Video tab, select the newly added camera under Archiver then click Hardware and edit the Lens type.

2.Select your Camera position from the dropdown menu.

NOTE: Genetec may not automatically pick the correct lens type and
could fail to calibrate.

3.Select the correct Lens Type from the dropdown menu.

4.Click Ok and Apply at the bottom of the page to save changes.
The fisheye camera settings are now complete.

Viewing the Newly Added Camera

To view the newly added camera:

1.Open the Security Desk application from the Windows Start menu.

2.Log in and and select Monitoring.

3.Double-click the newly added camera to see live video.

4.Use the scroll wheel on the mouse or click the Viewing Mode icon to manipulate the image.

Genetec – Adding a Hanwha Camera to Genetec 5.7 or later

Summary:

This article will provide a step-by-step guide for adding a Wisenet camera to Genetec.

Step By Step Guide:

1. Open the Config Tool (Figure 1)

Figure 1

2. Click on the green plus symbol (Figure 2)

3. Select Video Unit (Figure 2)

Figure 2

4. Select Hanwha as the manufacturer (Figure 3)

5. The IP Address can be a single device or a range of devices. (Figure 3)

6. Provide the proper credentials and click “Add and close” or “Add.” Then, repeat for further units. (Figure 3)

Figure 3

7. Once added to the system, you will be able to view the stream from the Video Unit (Figure 4)

Figure 4

How do calibrate a Hanwha Fisheye Camera for use on a Genetec VMS?

Applies to Models: XNF, SNF, and QNF Series Cameras

Summary:

This article describes how to add a Hanwha Fisheye camera to Genetec, by set a lens code and calibrate the camera.

Note: The lens code will be determined by the model.
See this article for a complete list of codes.

Step By Step Guide:

1. Open the Config Tool, go to Video Unit.

2. Select the Video Unit in question.

.

3. Select the Hardware Tab of the Fisheye camera to be configured.

4. Set the Lens Type to Panamorph.

.

5. Click the Pencil to the right of the Panamorph dropdown.

.

6. Set the orientation to either ceiling or wall.

7. Select the proper Lens Type  from the list (See De-warp Code article link below.)

8. Click calibrate once the code is registered.

Note: If it fails check the motion detection tab for an improperly configured Event or
Motion Schedule.

Click here for Immervision De-warping codes

.

<p>The post How to use Wisenet cameras with 3rd party VMS first appeared on NVR IPCAMERA SECURITY.</p>

Security Systems Basic Operation Guide

1. Arming the System:

   • Away Mode: Protects all sensors (doors, windows, and motion). Use when leaving the premises.
   • Stay Mode: Protects perimeter sensors (doors and windows) but not motion sensors. Use when staying inside.
   • Enter your code on the keypad and select the desired arming mode.

2. Disarming the System:

   • Enter your code on the keypad within the designated time frame (usually 30 seconds) to avoid triggering a false alarm.

3. Responding to an Alarm:

   • If you accidentally trigger the alarm, immediately enter your code to disarm the system.
   • If you suspect an actual intrusion, evacuate the premises and contact the authorities.
   • If you have a monitoring service, they will contact you to verify the alarm and dispatch help if needed.

Additional Features

Many modern systems offer advanced features like:

• Remote Control: Arm and disarm your system from your smartphone or computer.
• Home Automation: Integrate your security system with other smart home devices like lights, locks, and thermostats.
• Video Surveillance: Monitor your property with security cameras and receive alerts on your mobile device.

Important Tips

• Read the User Manual: Familiarize yourself with the specific features and operation of your system.
• Test Your System Regularly: Ensure all sensors and alarms are functioning properly.
• Change Your Code Periodically: Prevent unauthorized access to your system.
• Keep Emergency Contacts Updated: Provide your monitoring service (if applicable) with current contact information.

Remember: This is a general guide. Specific operation may vary depending on your system’s make and model. Always refer to your user manual for detailed instructions.

How App Sensitivity Translates to Recorder Levels

When setting up your security system, adjusting the motion sensitivity plays a crucial role in ensuring the system works as intended. Whether you want to reduce false alarms caused by pets or capture even the slightest movement, the sensitivity setting is a powerful tool. However, it’s important to understand how the app settings correspond to the recorder’s settings to avoid any confusion.

This guide will walk you through how sensitivity levels in your app map to the actual settings in the recorder and explain an important quirk: changes in the recorder’s settings don’t sync back to the app.

App Sensitivity Compare with Recorder Sensitivity

In the app, you’ll find sensitivity options in percentages. Each percentage corresponds to a sensitivity level in the recorder:

Unfortunately, the highest sensitivity level in the recorder (Level 8) isn’t accessible when adjusting through the app.

DID YOU KNOW? Changes made through the app immediately update the recorder’s settings. However, changes made directly in some recorders do not reflect in the app. This means if you adjust the sensitivity level in the recorder, the app will still display the last sensitivity setting it sent, which may not be accurate anymore.
It is recommended to always use the app to ensure the displayed sensitivity matches the actual setting. Change the sensitivity via Modes which you can learn more here.

Tips for Choosing the Right Sensitivity Level

Conclusion

Understanding how your app’s sensitivity settings translate to your recorder ensures you can fine-tune your system for optimal performance. Remember that while the app can control sensitivity conveniently, changes made directly in the recorder don’t sync back to the app. This small quirk can create confusion, but with the insights provided here, you’ll always know how to keep your settings aligned.

How to Disable the Watermark on Your Recorder

By default, the Swann logo is overlaid as a watermark for each camera.

NOTE: Once disabled, future recordings will not have the watermark.

How to digitally zoom in or out on a Recorder?

This works on both Live View or Playback from the unit itself.

Option 1:

If you are viewing multiple cameras in a single view, view one channel in full screen (double-click), then use the mouse to:

Option 2:

1.To enter Zoom mode, left-click a camera in Live View mode then click the “Zoom” button on the Camera Toolbar.

2.To zoom, move the mouse to the area or object that you want to zoom to then use the scroll wheel on the mouse to zoom in or out.

3.When zoomed in, click and hold the rectangle (as shown bottom right of the screen) to scroll around the image.

4.Right-click to exit.

To return to multiple camera view, double-click the mouse from the screen above.

Frequently asked questions about digital zoom

Can I zoom out further than the camera’s normal view?

How to change the small or lower-case letters on the on-screen keyboard display to upper-case letters

How to change the small or lower-case letters on the D1 on-screen keyboard display to upper-case letters.

Using the mouse, click the “ab” letters on the right side of the text box and it will change mode from lower-case letters to upper-case letters.

How to Change the Resolution of the Recorder

How to change the position of the Date and Time display bar on my DVR

You can adjust the position of the OSD from the menu display of the DVR. It has to be done directly from the DVR, using the monitor that is connected either to its VGA or HDMI output.

You simply open the menu of the DVR, go in the menu display, and then, from the camera tab, click on SET next to the OSD Display Position.

Afterward, with the mouse connected to the DVR, left click on the date and time display , hold down the button and drag the display wherever you wish .

The position chosen for the Date and Time Display will be reflected on the live view on your computer screen, should you access the DVR through the Network Interface ( and also on the recorded videos if you have enabled record date from the Display menu of the DVR ).

How to Change the Camera Layout on Your Recorder’s Live View

This guide is to show you how to do the following for the models above:

NOTE: The layout and arrangement will revert to a default state upon reboot.
If you want a fixed order of channels (e.g., Front door on ch1, Backyard on ch2, and so on), you need to change the input port or in the settings.

Change the number of cameras showing in Live View

1.Right-click or move the mouse cursor to the bottom of the screen to see the Menu Bar.

2.Choose from one of the following for your preferred view:

Icon	Description
	If you have 2 to 4 cameras, choose to display as 4-camera view.
	If you have 7 to 8 cameras, choose to display as 8-camera view. The 9th box will display the Swann logo only. This box cannot be customized nor disabled.
	Click this to select from one of the multi-screen viewing modes available. For an 8-channel recorder, it will show 6-camera view and 8-camera view.
	Click this to repeatedly cycle through each video channel full-screen. Each video channel will be displayed for five seconds.

Change the layout of the cameras in Live View

1.Left-click a camera (e.g. Channel 1) & drag it to reposition it.

2.Drop (release the left-click button after holding) over a different area or the desired box.

3.Repeat for other cameras.

For example in the image below, Channel 1 was moved to 2nd position while Channel 2 was moved to 1st position.

How to block trees or unwanted movement from recording in my DVR / NVR or triggering too many notifications

NOTE: This article also applies if you receive too many notifications on the app triggered by non-human objects.

PIR sensors can detect heat (infrared radiation) from objects within and even outside the camera’s field of view. Paired with moving objects captured by the camera like trees, swaying objects in sunlight, or cars passing, it can trigger the camera to record.

In this article, you will learn what settings on your recorder you can configure to virtually eliminate false triggers.

Remove The ‘Red Boxes’ From Constantly Moving Objects

The ‘red boxes’ shown above are the areas where the camera can detect movement. If trees are constantly moving or your camera is facing the road, you might want to remove these boxes so it doesn’t trigger on those areas. Here’s how you can remove it:

Any movement on the red areas or boxes will be picked up.

Set up Analytics

DID YOU KNOW? Only selected units or kits have the capable hardware to have Analytics, and each has its own set of Analytics available. The units are:

In a nutshell, Analytics provides you with much greater control over how your system detects motion. Below is a YouTube playlist that explains how a specific type of Analytics work.

You can also check your recorder’s manual for more details.

Relocate Or Reposition The Camera

The ideal position of the camera is 7-8 feet high, pointing downwards at an angle to cover the area where people will be walking across the camera’s path, and pointing the lens away from direct sunlight.

Visit the following links for more information about what heat sources outside of the camera’s field of view that can trigger the camera’s PIR sensors for recording and notifications:

NOTE: This should be a last resort only if lowering sensitivity, configuring area setup, nor analytics are not feasible options.

Does The Camera Still Record Events If Internet is Down or Offline

Answer: Yes

It will save the recordings to its internal memory or micro SD card when the camera gets triggered. Once the internet is back, it will attempt to upload the event clips during the downtime.

NOTE: SWIFI-TRACKCM only records to its micro SD card, regardless of whether it is online or offline.

How long will the SWIFI camera record?

Shortest:10 seconds

Longest:60 seconds (1 minute)

If the trigger (sound or movement; depending on what triggered the camera to record) is continuous for more than 60 seconds, another clip will be made.

For example, there was a continuous movement across the field of view of the camera within the PIR range for 135 seconds, about 3 clips will be recorded:

NOTE: If your camera isn’t recording as much as you’d expect, increase the Sensitivity setting. You can find this option under Detection Settings in your camera’s settings.

How do I optimize the motion detection?

Answer: PIR sensors work optimally when the subject of detection passes across their front. The more the object must “cross” the front of the video doorbell the better the detection reliability. When placing your video doorbell try to avoid situations where the subject would move straight toward the video doorbell if possible. You may need to experiment with the sensitivity settings in the app and video doorbell placement to get the ideal mix of detection and battery life as too much sensitivity can reduce battery life.

How can I play H.265 files on my PC?

When exporting videos from your NVR, you are given the option to export the player as well, which will then transfer a copy of the player onto your USB thumb drive.

This player allows users to view H.265 files on their PC and supports digital zoom and multi-channel playback from different channel files as well.

Click here to download the file.

How to Factory Reset a Stand-alone camera

Factory Reset is a complete reset of your device to its original factory settings. Also known as a hard reset. Factory resetting your camera can help resolve technical problems. It will perform the following, except unpair the camera (if currently paired) from the Swann Security account where it is currently paired:

NOTE: If you want to transfer the camera to another account, it needs to be unpaired by following this article: How to Unpair my Device from my Swann Security Account then pair it to the other Swann Security account by following this article: How to Pair Your Stand-alone Camera Using the Swann Security App

How to factory reset via physical button

Type the model number of your camera below to learn how to Factory Reset your camera.

Once donce, you have to do the pairing process again. Follow this article: How to Pair Your Stand-alone Camera Using the Swann Security App

Conclusion

A factory reset is a simple way to fix camera issues and start fresh. Just remember to back up any important data before resetting, if still possible.

How To Optimize Motion Detection

Answer: PIR sensors work optimally when the camera is mounted around looking down somewhat and the subject of detection passes across their front. The more the subject “crosses” the front of the camera the better the detection reliability.

When placing your camera, try to avoid situations where the subject would move straight toward the camera if possible. You may need to experiment with the sensitivity settings in the app and camera placement to get the ideal setting.

How to Set the Correct Date and Time on a Recorder?

SYSTEM > GENERAL > Date Format

How to Set the Date and Time on a Recorder

What to do if date and time are not updating automatically

If your DVR does not have internet connection, we recommend that you set up the following manually:

What time zone to set if you are unable to find your city

Time zone is based on GMT or UTC. Options range from -12:00 to +12:00.

Here are the conversions for common regions if you are unable to find your city in the dropdown:

If you are not in the regions above, use Google to convert your location’s time zone in GMT or UTC format. E.g. Pacific Standard Time in UTC is -8:00.

What to do if time is 1 hour ahead or behind: enable DST

Daylight Savings Time is applicable to the following regions where the clocks offset automatically by 1 hour.

How to Turn Off, Turn On, or Reboot Stand-Alone Cameras

Stand-alone cameras are an ideal security solution for homes and businesses, offering flexibility and convenience without needing a recorder to save clips. These cameras typically run on different power sources, such as built-in rechargeable batteries, power adapters, or direct AC connections. Whether you’re addressing a technical issue, performing routine maintenance, or learning to operate your device, knowing how to turn the camera off, on, or reboot it is essential.

How to…

Type the model number of your camera below to learn how to Factory Reset your camera.

Conclusion

Taking control of your stand-alone camera’s power and reboot functions is simple and helps maintain its reliability over time. Whether your device is powered by a rechargeable battery, a power adapter, or connected directly to AC, following the proper steps ensures smooth operation. By familiarizing yourself with these basic processes, you’ll keep your security system functioning efficiently and enjoy the peace of mind that comes with a dependable setup. Security is about control, and understanding these essentials puts you in charge.

<p>The post Security Systems Basic Operation Guide first appeared on NVR IPCAMERA SECURITY.</p>

NVR systems offer several important benefits for home security and CCTV:

Overall, NVR systems play a crucial role in home security and CCTV by providing centralized management, high-quality recording, remote access, scalability, advanced features, and reliable storage. They enhance the effectiveness of your surveillance system and help protect your property and loved ones.

In this list you will find the best open-source NVR solution for the web, Linux, Windows and macOS.

Best Free Open Source NVR Solutions

1- OS-NVR

OS-NVR is a highly versatile and user-friendly mobile-friendly closed-circuit television (CCTV) system.

With its state-of-the-art custom-built front-end, it ensures optimal performance not only on mobile devices but also on low-end devices, providing an enhanced viewing experience for users across various platforms.

The robust back-end, developed in Go, leverages the power of FFmpeg for efficient and seamless video processing, enabling smooth playback and reliable video capture.

With its cutting-edge technology and innovative design, OS-NVR is a game-changer in the field of video surveillance, offering unparalleled features and functionality for both personal and professional use.

2- ZoneMinder

ZoneMinder is a comprehensive surveillance solution that includes a set of integrated applications. It allows for the capture, analysis, recording, and monitoring of CCTV or security cameras connected to a Linux-based machine.

ZoneMinder is designed to run on distributions that support the Video For Linux (V4L) interface. It has been tested with video cameras connected to BTTV cards, various USB cameras, and also supports most IP network cameras.

Features

.

3- BashNVR

BashNVR is a simple yet powerful Network Video Recorder (NVR) solution written entirely in Bash scripting language. With BashNVR, you can effortlessly record and store high-quality video footage from your IP camera by leveraging the capabilities of FFmpeg, a widely acclaimed multimedia framework.

By seamlessly integrating with FFmpeg, BashNVR ensures the smooth recording of the RTSP stream, guaranteeing that not a single moment of your camera’s feed is missed. Whether you need to monitor your home, office, or any other location, BashNVR provides a reliable and efficient solution for capturing, managing, and storing your video recordings with ease and convenience.

Features

.

4- Open Source Network Video Recorder (NVR)

.

This is an open-source web application to monitor your IP Security Camera network, continuously record camera feeds to your computer’s hard drive, and monitor motion events through a web app.

Features

In addition, if your camera’s motion sensor triggers a detection, the app will take a still of the detection, and run a Object Detection process, to tag the still with the objects in the picture. You can then use these tags to filter and review your motion events. This is very useful to avoid false positives, like the sun going behind a cloud, or a rain shower.

5- Network Video Surveillance (Android)

This is an open-source JavaScript Network Video Surveillance system that you can download, install and setup on your server.

Features

6- Simple Network Video Recorder (Node.js)

This is a simple open-source self-hosted Network Video Recorder (NVR) that is designed to run on cheap hardware, such as a Raspberry Pi with a hard drive. 24/7 video streams from network cameras are saved, and the recorded files are browsable from a basic web interface.

7- Hover

This is an open-source free Home network video recorder for IP camera (based on VideoLAN).

This software is designed to be used with Hikvision IP cameras that support RTP H.264 streaming. The main goals of this recorder are:

License: GPLv3

8- Fenix

.

Fenix is a free and open-source computer based NVR (Network Video Recorder) with AI capabilities.

9- Shinobi

Shinobi is an open-source CCTV solution written in Node.js. It is designed with a multiple account system, streams video via WebSocket, and supports direct saving to MP4. With Shinobi, you can record IP Cameras and Local Cameras.

10- Camera.ui

Camera.ui is a web-based application that functions as a NVR (Network Video Recorder) for controlling RTSP capable cameras.

It offers features such as live streams, a resizable camera overview, multi-language support, motion detection, image recognition, notifications via various platforms, local saving of snapshots/videos, prebuffering, a user-friendly interface with customizable themes, and integration with Apple HomeKit.

Features

11- Viseron

Viseron is a powerful and versatile self-hosted software solution designed for local use only. It serves as both an NVR (Network Video Recorder) and an AI Computer Vision platform.

With Viseron, you can enjoy a wide array of advanced features that enhance security and surveillance. These include highly accurate object detection capabilities, which can identify and track various objects in real-time. Additionally, Viseron offers robust motion detection functionality, allowing you to receive instant alerts whenever any movement is detected within your monitored area.

Furthermore, Viseron’s cutting-edge face recognition technology provides an added layer of security, enabling you to easily identify individuals who enter your premises. This feature can be particularly useful for keeping track of authorized personnel or for monitoring access to restricted areas.

Viseron can be install on the cloud, Windows, Linux, or macOS.

12- Frigate

Frigate is a local NVR designed for Home Assistant that utilizes AI object detection using OpenCV and Tensorflow for IP cameras. It offers tight integration with Home Assistant, minimizes resource use, leverages multiprocessing for real-time object detection, communicates over MQTT, records video based on detected objects, supports 24/7 recording, re-streaming via RTSP, and offers low-latency live view with WebRTC and MSE support.

Features

.

13- Moonfire

Moonfire NVR is a comprehensive Network Video Recorder (NVR) solution designed for video surveillance. It offers a range of features and functionalities to capture, analyze, and store video footage from IP cameras.

With Moonfire NVR, you can easily manage and monitor your camera feeds, configure settings, and access recorded videos. It provides a user-friendly interface and supports various advanced capabilities such as motion detection, image recognition, and live view.

Moonfire NVR is a reliable solution for ensuring the security and surveillance of your premises.

14- Rapidvms

Rapidvms is an open-source Video Management System (VMS) and Network Video Recorder (NVR) solution. It provides a comprehensive set of features and functionalities for video surveillance. With Rapidvms, you can capture, monitor, and manage video streams from IP cameras.

It offers advanced capabilities such as motion detection, recording, and playback of video footage. Rapidvms is designed to be user-friendly and customizable, allowing you to configure settings and access recorded videos with ease.

As an open-source solution, Rapidvms provides flexibility and the ability to customize and extend its functionality according to your specific requirements.

15- Motion

Motion and MotionPlus are configurable programs that monitor video signals and perform actions when movement is detected. Motion is the original software, while MotionPlus is a newer application that adds new functionalities and removes rarely used ones.

The applications include features such as video recording, live streaming, script invocation, database logging, customizable masks, and support for various types of cameras and devices.

The applications include the ablity to:

Use with many types of devices:

.

16- veyesys

Veyesys is an open-source Network Video Recorder (NVR) and Video Management System (VMS) that provides a comprehensive solution for video surveillance. It offers a range of features and functionalities to capture, monitor, and manage video streams from IP cameras.

HTML5 RTSP Gateway

Veyesys includes an HTML5 RTSP gateway that enables real-time streaming protocol (RTSP) video feeds to be accessed and viewed through a web browser. This allows for seamless and convenient access to live camera feeds without the need for additional software or plugins.

Features

.

<p>The post Best Free Open Source NVR Solutions first appeared on NVR IPCAMERA SECURITY.</p>

This is a user guide for CMSClient version V1.00.00.47, it’s applied to software version is equal or newer than V1.00.00.47. If you are running older version (e.g. V1.00.00.46, V1.00.00.45), please download and upgrade your existing one to the latest. It should be noted that Yoosee has no app be compatible with Windows smartphone. If you have a smartphone running Windows OS, obviously you can not use Yoosee camera. The Yoosee software team will not release App for Windows based smartphone.

What CMSClient does?

CMSClient provides users a centralized video surveillance solution. It allows users to manage multiple cameras simultaneously, users can preview, record, playback, even receive alarm alerts by using it.  Users also can change yoosee camera’s network settings (such as IP address, gateway, DNS), can shift recording video resolution from SD to HD, can modify camera’s password.

Installation of CMSClient software

The software doesn’t contain any virus, if your anti-virus software report virus warning, please check if you have downloaded the software from official website. The software requires permission to access your network/Internet, it uses RTSP stream protocol to communicate with cameras locally, and P2P protocol to communicate with Internet cameras. When installing the software, ensuring it allows to pass Windows firewall.  The software will keep communicating with remote servers intending to establish P2P connection, it doesn’t spy your video, doesn’t transmit/upload any video clips to remote servers.

Logon CMSClient Software

CMSClient software now allows users to login through three different types of account.

• Admin login: local login, don’t require users to register an account. No need to input password, click “OK” to login immediately. The software can automatically discover local cameras, but can not discover Internet cameras.
• Phone Number login: remote login with your registered yoosee account, after logon, the software will list added cameras in your account.
• Mail/user ID login: remote login with your registered yoosee account, after logon, the software will list added cameras belongs to your account.

Moreover, select either “Phone number login” or “Mail/user ID login”, the software can receive motion detection (or sensor triggered) alert to computer. When motion detection alarm occurs, the software will pop-up a new window automatically to alert users, it also can play selectable audible automatically to remind users.

How to add Yoosee Cameras?

After logon, CMSClient will automatically discover local connected cameras, click “Add all” to add them into your software. Please note the displayed p2p password and rtsp password default is “qwe123”, it’s an incorrect password, just ignore them.

Except adding automatically, users can click “+” icon on the left bottom to manually add cameras. In “Device manager” window, local connected cameras will be listed on the left column, click “>>” button can add to software which will appear in right column. Click “Manual add device”, you can add local connected cameras via entering device ID, device password, RTSP password. Click”Add shared device” to add cameras as a guest user. In pop-up windows, you should paste the shared link. To know how to get shared link, you can read this article – How to use Yoosee App’s sharing function?

How to use CMSClient software?

Once you added devices to software, you’re able to use each functions of it. Select device you want to manage, right click mouse will pop-up a menu list.

• Device property: change camera name, device password, rtsp password and group.
• Delete node: delete camera from this list/software.
• Start monitoring: start to preview real-time video (if it shows you a crying face, it means password is incorrect)
• Smooth/standard definition/high definition: before click start monitoring, you should choose default image resolution, smooth equals low resolution, standard definition equals VGA (640×480), HD equals 1280×720 or 1920×1080.
• IPC config: you’re able to tweak camera’s network settings (e.g. IP address, DNS), record video resolution (SD, or HD), password.  It only works on the premise that your camera’s password is correct. If you encounter “network timeout” “permission error” “password incorrect” error, to solve this, you need to logon software with yoosee registered account.

CMSClient Playback Function

You’re able to playback recorded video clips right from your computer. The CMSClient can only allows users to play remotely and locally recorded video clips, but also can allow you convert them to friendly .mp4 files which can be recognized and played by regular media players.

Click “Search” button on the left top, the camera can search files, click the file name to playback. Additionally, you can click folder icon to open a file to play it. All yoosee camera will record video with .av file extension. These raw files can not be recognized or played by regular media players, you can use the converter which the software has included to convert .av files to .mp4 files.

If you don’t want to install and use CMSClient software, still want to play .av files in another computer, you can read this article – How to play .264 video files from IP cameras/DVRs/NVRs?

CMSClient software is a powerful video surveillance management tool, it includes other function to provide a great flexibility. Click gear icon on the top of software, it will pop-up a “CMS config” window.

• File save path: select the folder path to store recorded video footage.
• Reserve space: allowing users to modify reserved space for video storage in your HDD.
• Record time for package: the time length to patch a video file when recording video. If the value is “60” min, the software will patch/generate a video file in every hour when software is recording on computer.
• Cycle record: turn on/off over-write function, automatically erase/overwrite HDD when space is full.
• Auto start record when monitoring: record video while watch video stream.
• Connect all of device automatically: automatically display video for all cameras/channels after logon software.
• Render mode: Directdraw, GDI
• Monitor: auto, rtsp, p2p
• Message notification: choose whether receiving message notification or not when there is a motion detection alarm.

If you logon software with registered yoosee account, the software will have “Alarm trigger” option. This open allows you to select time length of pop-up video when alarm occurs. You’re able to choose different audio files, the computer will play the audio to remind users.

<p>The post User guide for Yoosee App PC Software – CMSClient first appeared on NVR IPCAMERA SECURITY.</p>

How to reset TVI DVR/ POE NVR / Wireless NVR (ZSWNVK-H) System when you forgot the password?

1) You can find the correct model number on the label at the bottom of the DVR / NVR System.

2) Find the DVR / NVR’s device ID/UID.

A. You can find the DVR’s ID on the label of the DVR / NVR.

How to reset Password Zosi DVR NVR Poe All Model

B. Or you can also reboot the DVR / NVR system and wait until Wizard Page display, then find the UID.

3) Please send us the model number and device ID / UID, we will create a super password for you.

    NOTE: The User Name corresponding to super password must be ‘admin’.

                 Once you set super password this time, the login password should be blank

                 in the next time when you reboot it or log in again.

                 You can go to DVR’s Main Menu – Setup – User – Change password to set a new

                 password. (Please keep the old password blank, you just need to input the new

                 password and confirm password.)

Beyond that, you can also upgrade software by means of upgrade file from us, then reset password when reboot DVR.

Connecting the DVR / NVR to the internet

This method works for the following models of DVRs / POE NVRs / Wireless NVRs:

4-Channel DVRs / POE NVRs / Wireless NVRs:

ZR04ZN;   ZR04ZM;   ZR04FN;   ZR04FM;   ZR04CN;   ZR04CM;   ZR04JS;   ZR04TS;   ZR04TN

ZR04RN;   ZR04RM;   ZR04EN;   ZR04EM;   

ZR04DS;   ZR04MS;  

8-Channel DVRs / POE NVRs / Wireless NVRs:

ZR08ZN;   ZR08ZM;  ZR08FN;   ZR08FM;   ZR08BN;   ZR08BM;   ZR08CN;   ZR08CM;   ZR08KS;   ZR08TN

ZR08RN;   ZR08RM;   ZR08EN;   ZR08EM;      

ZR08DS;   ZR08DP;   ZR08MS;   

16-Channel DVRs:

ZR16ZK;   ZR16JK;   ZR16BK;   ZR16CK

(You can find the model number on the label at the bottom of the DVR.)

If your CCTV DVR or NVR don’t have a built-in WiFi support, then you have to run internet cable (CAT 5 or CAT 6 Ethernet cable) to connect your DVR or NVR to the internet via the router.

• Connect one end of the Ethernet cable to the Ethernet input on the back of the DVR.
• Connect the other end of the Ethernet cable into a device providing an active internet connection, such as a router or modem.
• Test your internet connection to confirm that it is active by going to the Network > Network screen.

1) Right click mouse—go to Main Menu > Setup > Network.

2) On the Network tab, ensure the “Obtain an IP Address Automatically” option is enabled, and that there is no information in the PPPoE fields.

3) Once you’ve ensured there is no information in the PPPoE field and that the “Obtain and IP Address Automatically” option is selected, select the “Test” option.

If “OK” is displayed, the local area network is connected successfully.

If the DVR is not able to connect to the internet, you will get a message that states “Cannot Connect to Network”.

NOTE:

In order for other devices to connect to the DVR through the router, the DHCP setting must be enabled from the router’s settings page.

If you still cannot connect to the network, please ensure that you don’t have a firewall active on your network that may be limiting the connection.

You may need to open ports 80, 5000, and 5001 on your router, if they’re currently being blocked by te firewall. This typically only happens on commercial internet accounts, as they deal with sensitive transactions, but occasionally a firewall on a residential line will also block these ports.

If you’re unsure how to open ports on your router, you will need to speak with the router manufacturer.

FAQ:

1) What’s DHCP?

DHCP is a type of internet networking approach. It stands for Dynamic Host Configuration Protocol. It means that a router assigns IP addresses to each of the devices on the network, allowing them to communicate with other devices in or outside the network.

In context of our systems, the setting related to DHCP is called DHCP server status. This setting enables your router to obtain the static IP address on the DVR and broadcast that IP to the app so it can locate your DVR. This setting needs to be enabled on a router for the apps to be able to connect to the DVR systems.

2) For example: How to set up a linksys E5350 Router?

Once you’ve logged into the router settings, you’ll want to select “configuration” at the top, and then “Connection > Local Network” in the menu on the left. You should see this page:

​

You’ll want to ensure the checkbox beside “DHCP server” is checked off, and set the start IP address to 100 as shown in the image. Leaving the other settings here as they default should be fine. Once this is done, select “save.” Before proceeding with the next steps, try using the app while not connected to local WiFi. If you can see the live feeds, you don’t need to complete the steps below.

If you can’t, you’ll need to open the ports in the firewall. On the left menu, select “Security”, and then “Single Port forwarding” as shown in this image:

​

Select the button on this page for “Add a new Single Port Forwarding”, and this window should appear:

​

The number you want to enter in the “To IP Address” field is the last three digits of the DVR’s static IP, which you can find on the Network page of the DVR. (Main Menu > Setup > Network)

Application and protocol can be left as they are, and you’ll want to check off the “enabled” box. You’ll need to do this 3 times, using the following information:

1.
Application Name: DVR HTTP
External Port: 80
Internal Port: 80

2.
Application Name: DVR Mobile
External Port: 5000
Internal Port: 5000

3.
Application Name: DVR E-mail
External Port: 5001
Internal Port: 5001

After filling the box with the necessary info for each port, select “apply”, and then hit the add button again to reopen the window. Once all 3 ports are opened, try testing the app again.

Note:  different Routers may have different setting interfaces.

More questions, please feel free to contact us.

Our Whatsapp:  +1-866-841-6932

Support Email address:  service@zositech.com

Our Facebook:  https://www.facebook.com/ZosiTechnology/

Support center: support@zositechhelp.zendesk.com

<p>The post How to reset Password Zosi DVR NVR Poe All Model first appeared on NVR IPCAMERA SECURITY.</p>

How to add a Hikvision NVR to Hik-Connect

Before you start…​

Part 1: Enable Hik-Connect on the NVR…​

.

.

.

.

Part 2: Set up Hik-Connect on your mobile phone or tablet…​

.

.

.

Part 3: Add the NVR to your Hik-Connect account…​

.

.

.

Other tips…​

Guides for Hikvision NVRs with V5 firmware

How to set up motion detection and alerts on a Hikvision NVR

What is Motion Detection and why is it useful?​

Motion detection is one of the easiest events to set up and will notify you as soon as a person or vehicle enters a predefined detection zone in your scene. Traditionally, it would just rely on lots of pixels changing between frames in your camera’s video stream, which would indicate movement in the scene.

Of course, this would cause lots of alerts for things you are not interested in, such as animals, moving plants and rain. Hikvision’s Acusense cameras and NVRs now have something called Motion Detection 2.0, which cuts the false-positive detections right down as will only notify you when people and/or vehicles are in the scene by learning what they look like. In this simple step-by-step guide, we will show you how to get motion detection set up on the new NVR 5.0 web interface.

Step 1: Go to your NVR’s Motion Detection configuration page…​

Step 2: Configure your Motion Detection zone and rules…​

​

Quick tip…​

If you find that the camera preview is too small when drawing your detection zones, you can switch the view to full screen by clicking on the Full screen (four arrows) button in the toolbar, and then exit full screen by pressing Esc on your keyboard.​

Step 3: Set the arming schedule to specify when you want Motion Detection active…​

​

Quick tip…​

If the 30-minute segments are not precise enough for you, you can finely tune a period of arming or disarming by double-clicking on the segments and specifying your start and end times in minutes using the arrows.​

​

Step 4: Set what you need the NVR to do when a camera detects a target…​

How to connect an IP camera to a Hikvision NVR

Adding cameras to your Network Video Recorder (NVR) is a crucial step in any CCTV setup. Not only does it allow you to store and access all your camera recordings in one place, but it also simplifies camera configuration. In this simple step-by-step guide, we’ll show you how to add cameras to a Hikvision NVR using the new NVR 5 web interface.

.

Why add cameras to an NVR?​

.

Before you start…​

Before anything, to be able to add your IP cameras, you need to make sure that:
.

.

How to add your cameras using the V5 GUI…​

Step 1:​

Open a web browser and enter the IP address of your NVR in the address bar. If you are not sure what this is, use the SADP tool to find it.​

Step 2:​

Log in to the NVR using the “admin” username and password you have set on it.​

​

Step 3:​

Go to: Device Access > Device Configuration > PoE Settings​

​

If you are connecting your camera via the Plug-and-Play method, then make sure that Network Camera Plug-and-Play is enabled on the POE port you will be connecting the camera to on this page.​

​

For any camera with a cable run under 100m, leave the Network Cable Distance as Short Distance.​

​

If you are connecting your camera manually by IP address, disable the Network Camera Plug-and-Play option for the channel that you plan to add the camera to.​

Step 4:​

Go to: Device Access > Device > Video Device​

​

For any Plug-and-Play camera, just make sure that it is in its inactive default state and then connect it to the port you reserved in step 3. After 20 seconds or so, the camera Status should turn to Connecting and then Online (you may need to click on Refresh to see this).​

​

For Manually added cameras, if you can see the camera in the List of Online Devices section, then just tick the box for the camera and then click + Add to Device List, which will then automatically add it to one of the channels you disabled Plug-and-Play on in the last step.​

Alternatively…​

Click on +Add at the top of the page and fill out the fields as follows:​

​

IP Address: Enter the IP address of your camera, using the ‘Test’ button to verify there is a camera at that address. ​

Device Name: This can be anything you like, as it is the name the camera will show with on your NVR. ​

Protocol: Select the camera’s manufacturer from this list, or failing that, use the ONVIF protocol (your camera will need to have ONVIF enabled for this to work). ​

Management Port: Enter the Server port set on the camera, which you can find in the SADP tool or in Network>Basic Settings>Port in the camera’s web browser interface. If you haven’t changed this, it is usually 8000 by default. ​

User Name: “admin” or the username of any other users set up on that camera. ​

Password: The password set with that user on the camera – if this is the same as the ‘Default Activation Password‘ you have set on the NVR, then you can tick this box instead. ​

Transfer Protocol: ‘Auto’ is normally best. ​

​

When these are completed, click OK.​

​

Your camera should then appear in the list of devices with an assigned channel, and an Online status, meaning it has been successfully added.​

.

Extra tips…​

Source : https://www.use-ip.co.uk/forum/forums/guides-for-nvrs-with-v5-firmware.71/

.

<p>The post Guides for Hikvision NVRs with V5 firmware first appeared on NVR IPCAMERA SECURITY.</p>

Tapo was created to engage in the small intelligent appliances market, to help people adopt a new smart home lifestyle at an affordable cost. That’s why we insist on Smart, Easy, Secure.

.

What should I do if I fail to configure the Tapo Smart Plug?

The Tapo app will guide you step by step during the initial configuration, but you may not be able to get through all the steps due to some interference. This FAQ will tell you what to do if you have trouble getting through a certain step.

Case 1

The phone is looking for the smart device via Bluetooth or its default 2.4GHz WiFi, if you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

Tapo Smart Camera FAQ v1

Case 2

If you are unable to find your home Wi-Fi network, please refer to the following suggestions.

Troubleshooting tips:

1. The signal strength of your home Wi-Fi network is a bit weak, move the smart device closer to your router for a try.

2. Ensure your home Wi-Fi network is a 2.4GHz Wi-Fi network, the Tapo device does not support a 5GHz Wi-Fi connection.

3. If it doesn’t display the Wi-Fi name of the router automatically, please click on “RECAN” at the upper right corner to refresh the Wi-Fi list.

4. If the router’s SSID is hidden, please choose “Other” to input SSID and password manually.

5. Please change the wireless channel of the 2.4G Wi-Fi network to 1, 6 or 11.

6. Reset the device as per QIG/UG and go through the process again.

Case 3

If you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

1. Ensure you have selected the correct home Wi-Fi network and have entered the correct wireless password. If the Wi-Fi network or password is incorrect, click on “Choose a Network” and select the Wi-Fi network again.

2. Make sure your smart device is within the Wi-Fi range of your router.

3. Turn your phone’s or tablet’s Bluetooth off and back on.

4. If the problem persists, try to reset the smart device as per UG/QIG, and then set it up again.

5. Check if there is a firewall on your router. If yes, please turn it off.

6. Change the wireless security type of the 2.4G network to WPA2.

7. Try to connect the Tapo plug to the hotspot of your cell phone or another wifi network. If it works, please upgrade the firmware for the plug, then reset and reconnect it to your router.

.

What features does Tapo smart plug and Tapo smart switch support?

Currently the Tapo plug and switch supports the following features:

.

How to view Tapo camera on PC/NAS/NVR through RTSP/Onvif Protocol

The Tapo camera supports the RTSP and Onvif protocol, so it can work with third-party NVR or NAS devices that also support the RTSP/Onvif protocol. If a user wants to view the live stream of the camera with a third-party app like VLC Player, iSpy, here is the method for him.

Notes:

1. The username/password is the camera account that you created via the Tapo app. If you haven’t created the username and password, please follow the instruction of Step 1 in this article.

2. The IP address is the camera’s IP address assigned by your host router. You can find it on your host router’s DHCP list or in the Tapo app (Go to the Device Settings page of the camera and tap Device Info to see its IP).

3. If you want to view the live stream of the Tapo camera with a third-party app remotely, you will need to open port 554 for the camera on your host router first. Please enable the TCP forwarding for port 554.

4. You could use ONVIF standards to add the Tapo camera with its username/password and IP address. Please see the example of iSpy in Case 2 to know how to use onvif protocal to control the camera.

5. For Tapo C310, the resolution of the stream1 is determined by the video quality set on the Tapo APP.

If you need to watch the 3MP HD Video via RTSP, please change the video quality to Best Quality on the Tapo APP and use: rtsp://IP Address/stream1

6. If the Camera is inserted microSD card and subscribed Tapo Care, its RTSP stream will fail. You need to remove microSD card or cancel Tapo Care to get its RTSP stream.

7. If you find that there’s no or very little sound when using RTSP/Onvif to watch live stream, please adjust the camera microphone on Tapo APP.

Apart from the Tapo app, Tapo cameras can work with other third-party software to use and manage your Tapo camera.

Note: Before you start, make sure the computer/NAS/NVR and your camera are connecting to the same network or can visit the public IP and port of your camera.

Step 1: Create a camera account in the Tapo app

1. On the Home page, tap on your camera model card to go to the camera Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Advanced Settings, then select Camera Account to create an account (username and password) for camera login on other portals.

You will see a prompt like below (About Camera Account), please read it and tap Understand and Agree to Use, then you can create an account for the camera.

Note: The username and password should contain 6 to 32 characters.

Step 2: Add your Tapo camera on iSpy (Example of Onvif protocol connection)

1. Run the iSpy software on your computer.

2. Click Add on the top left menu and select ONVIF Camera.

3. Enter the Username and Password that you set for your camera on the pop-up window, select Network Address, and click Next. You can customize other parameters if needed.

4. Choose the video resolution and click OK.

5. Customize the camera settings as needed, including Microphone, Talk, Motion Detection, Alerts, Recording, Images, Scheduling, and Storage. You can also change all the settings later. Click Finish to complete adding your camera to iSpy.

6. After adding your Tapo camera to iSpy, you can monitor and manage it using the app. View the live, customize motion detection, check the recordings when motion detected, set recording schedules, record videos and more.

Step 3: Watch your Tapo camera on VLC (Example of RTSP protocol connection)

1.Open the VLC software, select Media > Open Network Stream

2.Fill in the URL of the Tapo camera

The URL of the RTSP live stream for the Tapo cameras will be:

For high quality stream1: rtsp://IP Address/stream1

For low quality stream2: rtsp:// IP Address/stream2

In some software, the URL need to add the port to access live stream, the default port is 554:

For high quality stream1: rtsp://IP Address:554/stream1

For low quality stream2: rtsp:// IP Address:554/stream2

If you fail to stream the Tapo camera via the RTSP/ONVIF protocol, you may refer to the article for the troubleshooting:

https://community.tp-link.com/en/smart-home/forum/topic/652710

To get to know more details of each function and configuration, please go to Download Center to download the manual of your product.

.

How to factory reset the Tapo or Kasa smart plug

.

To restore a Tapo or Kasa smart plug to its factory default settings and re-enable the setup mode, please press and hold the power button for 10 seconds.

The LED status for a factory reset varies by model:

After a completing the reset, you can then connect and configure the device in the Tapo App.

How to avoid noise when monitoring the sound from Tapo camera

Tapo cameras are capable of not only monitoring video stream from the camera, but also monitoring sound collected by the built-in microphone on the cameras. You can turn on/off the sound feature like the monitor screen as below. But to increase or decrease the volume, you need to press the volume button on your phone.

Why is there noise?

Noise is a physical phenomenon and it’s actually inevitable. Basically, the IP cameras including other brands’ have background noise more or less. And those cameras which seem to generate less noise probably have worse sound collecting performance. Tapo cameras are designed with a sensible sound collector which might take some noise in your monitor. Even though it is inevitable at present, we are still trying our best to make improvement and searching for better solutions.

How to reduce the noise?

1.     Please keep your mobile device away from the camera as much as possible. The Tapo camera is designed for remote access and monitoring via cloud service, local usage in close range may cause interference and noise between your mobile device and the camera.

2.    Please reduce the output volume below 50% since a louder volume may enlarge noise decibel. The value between 40%-50% is suggested with not only good sound quality but also minimum noise decibel. As long keep focus on our cloud camera you will find our progress on new models.

Your understanding is highly appreciated!

How to edit Home and Away Mode for Tapo&Kasa Cameras on the Tapo app

.

The Away mode and the Home mode are two different sets of Detection, Alarm, and Notification settings for Tapo&Kasa cameras. You can tap the button on the Tapo app>Cameras tab to quickly apply the preset settings to the cameras when you are home or away.

Note:

Here we take the Home Mode as an example.

For Tapo Cameras:

1. Open Tapo APP, find the Cameras tab at the bottom, and locate the Detection Mode section.

You can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three-dots option.

2. Click on Add Devices if you want to add more cameras to the Home mode.

Click on the Edit icon at the top right corner if you want to delete cameras from the Home mode.

3. Select the camera you want to edit the mode settings. Here we take Tapo C200 as an example, and you can change the Privacy mode, Detection, Alarm, and Notification settings of the camera.

Take the Motion Detection feature as an example. You can click on Motion Detection to turn it on or off, change the Motion Sensitivity, and set the Activity Zones on the Motion Detection page.

And you can also click on Detection>Person Detection or Baby Crying Detection to turn them on or off, and tap Alarm and Notifications to configure the related settings.

4. Click on the Back icon at the top left corner of the Tapo C200 page if you have changed the configurations, and click on other cameras if you want to change their configurations.

After completely presetting the Home or Away Mode, you can tap the Home mode or Away mode card on the Tapo app>Cameras tab to switch your cameras’ settings quickly.

For Kasa Cameras:

Here we take KC115 as an example.

1. Open the Tapo app, find the Cameras tab at the bottom and you can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three dots option.

2. Select the camera you want to edit the mode settings and enter the Detection & Alerts page.

3. You can change the Privacy mode, Detection, and Notification settings of the camera.

Tap Detection > Motion Detection to edit the motion detection function. You can adjust Motion Sensitivity.

Tap Detection>AI Detection to change your AI Detection feature, such as Person Detection.

4. After editing the detection settings, tap Detection & Alerts > Notifications to customize its current settings.

After completely presetting the Home or Away Mode, you can tap the card on the Tapo app>Cameras tab to switch all of your cameras’ detection settings to the mode you want.

.

How can I find the IP address of my Tapo&Kasa camera

Note: Some Tapo battery cameras or doorbells need to work with the hub and can’t connect to the router directly, which do not have IP address.

There are two methods to find the IP address of the camera.

Here we take Tapo C200 as an example.

Method 1: Via Tapo app

1. On the Tapo app> Home page, tap your camera model card to go to the Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Device Info and then you can find the IP address of your camera.

Method 2: Via the web management page of your router

Here we take the TP-Link router Archer C7 as an example.

1. Log in to the management page of your router.

2. Go to Advanced > Network > DHCP Server and locate the DHCP Client List section to find the IP address of your camera.

How can I view continuous recordings of Tapo&Kasa cameras on the Tapo app?

This article will show you how to view continuous recordings on the Tapo app.

Note:

For Tapo Cameras

Here we take Tapo C200 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

Click on Recording Schedule to see the detailed recording schedule settings.

Tap Edit on the Recording Schedule page if you want to change the Continuous Recording and Detection Recording schedule.

And please tap the tick icon at the top right corner to save your changes.

Step 3.

On the camera’s Live View page, tap Playback & Download, select the SD Card icon on the Playback page, select the date, and then you can drag the timeline to view the continuous recordings.

For Kasa Cameras

Here we take KC115 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

On the Live View page of the camera, tap Playback & Download > Playback to view all recordings. Drag the timeline and you can view recordings whenever you want and wherever you are.

What can I do if the video image is upside down on my Tapo&Kasa camera

Tapo&Kasa cameras support the function of Video Rotation, and if the camera video image is upside down on the Tapo app, please refer to the following steps to correct it.

Here we take Tapo C200 as an example.

1. On the Home page of the Tapo app, tap your camera model card or tap the Cameras tab>click on Manage on your camera model to go to the Live View page.

2. On the Live View page, tap the icon on the top right corner to enter the Device Settings page.

.

What can I do if I can’t find my Tapo camera on Tapo APP?

If your device does not appear on your app after completing the configuration process, please try the following troubleshooting suggestions:

1. If you are using a Wi-Fi wireless configuration to connect your camera, please check if the camera has successfully connected to the router. You can verify whether the camera is connected to Wi-Fi by checking the System light of your camera. For most Tapo Cams, if it is not connected properly, the LED light will blink red slowly. For the HomeKit version Camera, its LED light indicator will blink blue slowly. If the camera cannot connect properly, we recommend resetting the camera to factory default settings as per the User Guide and then reconfiguring the camera.

How to reset my Tapo camera

2. Check the DHCP settings on your router and ensure that the DHCP Server of your router is enabled. If the camera has already connected to the router properly, you will see the device in the client list of your router. If you don’t know how to do this, please contact your router’s customer support.

3. Please verify if there are any special symbols in your Tapo account（TP-Link ID） password. If there are, try to remove them and make the account password simpler by only using numbers and English letters. Then reset and add the camera from the beginning again.

4. Connect your smartphone to the same Wi-Fi network as your camera and check whether you can see it on the Tapo app. If you can see it, that means the camera fails to connect to the cloud for unknown reasons and you cannot access it remotely. In this case, verify if any firewall or security settings are blocking the connection to the Cloud Server. Temporarily disable any antivirus, firewall, or security software to see if it resolves the issue

.

5. Using a public DNS server may improve the connection, try changing your router’s DNS server settings to 8.8.8.8. If you don’t know how to do this, please contact your router’s customer support.

To eliminate potential issues with the router’s Wi-Fi network, it is recommended to use a mobile hotspot and configure the Camera to test its functionality.

Here are steps for using a mobile hotspot to test the Camera’s configuration:

Preparation: We suggest having two phones. Use one phone (Phone A) to create a hotspot and use another phone (Phone B) to download the Tapo app and complete the setup process.

Steps:

1. On Phone A, disable Wi-Fi and enable only mobile data.

2. On Phone A, navigate to phone settings and access the “Personal Hotspot” or “Mobile Hotspot” option, ensuring that the “Mobile Hotspot” feature is activated. Please make sure the created hotspot operates on a 2.4GHz network.

3. Set a unique name and password for the hotspot, different from your router’s Wi-Fi, to facilitate the Camera’s connection.

4. On Phone B, download the Tapo app. Follow the app’s instructions to add the device and complete the remaining setup steps as guided by the app.

Please contact TP-Link technical support with the following information if the issue persists after the above suggestions.

1) Your TP-Link ID or cloud account.

2) The model number of your TP-Link Cam and its MAC address.

3) The model number of the host router.

4) Whether you have tried all the suggestions listed above or not. If yes, what are the results?

<p>The post Tapo Smart Camera FAQ v1 first appeared on NVR IPCAMERA SECURITY.</p>

[All Cameras] How can I check if the camera IP is used by another device?

Question

How can I check if the camera IP is used by another device?

Answer

IP conflicts occur when two devices on the same network are assigned the same IP address. This can lead to connectivity issues, and it’s essential to resolve such conflicts to ensure smooth network operation. If you suspect your camera’s IP address might be used by another device, here’s how you can check and resolve it.

1. Disconnect the camera from the network.

2. Connect a PC to the same network as the camera. Then, open the Windows Command Prompt (cmd.exe).

3. Execute the ping command followed by the camera’s IP address:

ping <Camera IP>

If you are unable to locate the device or computer using the originally designated IP, consider setting a new IP address for the camera to avoid IP conflicts.

Vivotek IP Camera Troubleshooting v1

How to use PowerShell to test if the camera IP and ports can be accessed?

Question

How to use PowerShell to test if the camera IP and ports can be accessed?

Answer

There are several ways to test if your camera IP can be reached, one of the most used is the “ping” command:

Unfortunately, the ping command has its limitations and wont be able to verify if the ports of the pinged IP are open (ping commands are sent using random ports). In order to check the port connectivity you can use the “Test-NetConnection” command in power shell which can test connectivity to a specific IP and port. To do so please follow the next steps:

Step 1. Open the Windows PowerShell, you can do it by typing “PoweSheel” in the start menu search:

Step 2. Type the following command:

Test-NetConnection -ComputerName [IP address] -Port [port number]

Where the [IP address] is the camera IP and the [port number] is the port that you are trying to verify. 

Step 3. Press enter to run the command and the following will appear:

The process will take a couple of seconds and once finished it will display the connection status as follows:

If the connection cannot be stablished, the following error will appear:

Note: the same process can be used to check ND/VAST2/VSS connectivity (all of those devices/software uses different ports to communicate). 

If there is a connection error you can do the following to ensure that the camera port can be accessed:

If after checking the points mentioned above you are still unable to access the camera using its IP and port please contact Technical Support for assistance. 

[All cameras] How to reset your camera to factory defaults?

Question

How to reset your VIVOTEK camera to factory defaults?

Answer

All VIVOTEK cameras possess a reset button which can allow you to reset the device to factory defaults. To reset the camera to factory defaults please follow the next steps:

1. Locate the camera reset button, if you are unfamiliar with its location please go to our website and search for your camera model.

In the download section you will be able to find the “User manual” and the “Quick installation guide”, both documents have information regarding the location of the camera reset button.

2. Press and hold down the reset button for 10 seconds, the camera LEDs will start blinking rapidly.

The camera will reboot (LED will stop blinking), after rebooting it will begin the reset process (LED start blinking again).

3. Wait until the camera finish resetting. After 1~2 minute the process will be over.

Please note that resetting your camera to factory defaults will reset all the settings and configurations applied to the camera. So once the camera finished the process you will need to configure the device again to your needs. 

How can you troubleshoot when you cannot watch video streaming?

Question

How can you troubleshoot when you cannot watch video streaming?

Answer

When you’re unable to watch video streaming from a VIVOTEK camera, there are several troubleshooting steps you can follow:

1. Check that the browser is compatible with the camera:

VIVOTEK cameras are compatible with Internet Explorer for the 8000 series or older, and with Chrome and Edge for the 9000 series. Be sure to use the appropriate browser to access your camera. 

2. Upgrade the camera to the latest firmware available.

VIVOTEK constantly keeps improving camera firmware to increase product reliably and resolve know issues which might be related to the video stream. Please be sure to upgrade your camera to the latest version available:

3. Check if the camera sensor is still generating images

VIVOTEK cameras have a snapshot feature that works independently from the video stream and can be used to verify if the image sensor is functioning properly. If you find that your camera is not displaying videos, please use the following URL in your browser to see if you can retrieve a snapshot:

http://<Camera_IP_address>/cgi-bin/viewer/video.jpg

If there is no image displayed, this will mean that the video sensor might be compromised. 

4. Use and RTSP Player to verify if the camera can send data through RTSP

Try to use an RTSP player like VLC Media Player to verify if a VIVOTEK camera can send data through RTSP, you can follow these steps:

If the player cannot play videos, this could mean that the camera’s RTSP module is having trouble sending videos.

4. Reset the camera to factory defaults

Resetting the camera to factory defaults will return it to a state unaffected by any new external configurations. If you are experiencing video issues, please try resetting the camera to factory defaults to see if the problem can be resolved. The following guide explains how to reset your device to factory defaults: [All cameras] How to reset your camera to factory defaults?

If these steps do not resolve the streaming issue, contacting your camera vendor might be necessary. They can provide more specific guidance based on the exact model and configuration of your camera.

How to reload in Internet Explorer mode when browsing in Microsoft Edge?

Question

VIVOTEK legacy network cameras and Linux-based NVRs can only get streaming by installing plugins on Internet Explorer.

However, the Internet Explorer 11 desktop application will no longer be supported on certain versions of Windows 10 after June 15, 2022.

Microsoft encourages customers to move to Microsoft Edge.

This article will share how to reload in Internet Explorer mode when browsing in Microsoft Edge.

Answer

1. Open Edge browser.

2. Go to settings and more”…”→ Click ”Settings” → ” Default browser” → Choose “Allow” in Allow sites to be reloaded in Internet Explorer mode → Restart

3. Use Edge to access cameras or NVRs. (You will see this plug-in isn’t supported)

4. Go to settings and more”…” → Click “Reload in Internet Explorer mode”.

Note: Please add the address to trusted site if Edge show 401 Unauthorized.
How to add a website as a trusted site for Microsoft Edge 

Remember to install all required add-on and program.

You will see the image.

5. Enable “Open this page in Internet Explorer mode” → Done

<p>The post Vivotek IP Camera Troubleshooting v1 first appeared on NVR IPCAMERA SECURITY.</p>

TetherX Camera Setup Guide v2, Tether your video surveillance, alarm panels, network infrastructure and other IP or Serial devices to the cloud. Monitor the health of your sites, cloud record cameras and integrate with third party services.

The steps required to set up Samsung Cameras / DVRs and NVRs

Setting Correct Profiles

Please ensure you have 2 profiles configured on your device:

IP Cameras

Cameras are the easiest to set up and should work out of the box. If the cameras are not working for any reason, please try one of the following for the Analytics Path and Recording Path:

Multi-Sensor IP Cameras & Encoders

If your device is a multi-sensor camera or an encoder, please set the Analytics Path as follows:

NVR – Network Video Recorders

DVR – Digital Video Recorders

DVR recorders setup is similar to NVR setup with the following differences:

.

Can I use TetherX alongside HikConnect?

Can I use Hik-Connect on my Hikvision cameras and recorders?

Yes.

Please make sure that stream encryption is switched off under Configuration > Network > Advanced Settings:

HikConnect stream encryption uses a proprietary mechanism which is not available to third-parties. Please note TetherX will encrypt the stream to the highest standards, for more information please see our security white-paper.

Note: If you are still getting a broken stream or no live view, please try updating the camera and/or recorder firmware to the latest. There are known issues that have been addressed by Hikvision.

.

Live View – Technical Implementation Details

How TetherX implements live view to be compatible with all manufacturers

Introduction

The quality, latency and smoothness of live view streaming is dictated by many factors:

Available Streams from Cameras

Typically cameras will provide 2 video streams as well as the ability to request a single image. These limitations dictate what is and isn’t possible when it comes to both recording and streaming.

💡 Note: More expensive and speciality cameras will provide additional video streams and custom streams of crops/de-warps of the same image (e.g. 180 or 360 cameras).

The streams are usually accessed through RTSP and the images through HTTP. For example:

Formats

Transcoding vs Proxying

TetherX supports both transcoding and proxying/packaging. The differences between the two are as follows:

Transcoding is a process of taking the stream from a camera, decoding it and then re-encoding it into a different format. This is the ideal method to hit a specific requirement of Internet bandwidth and viewing size, but it is in most cases cost prohibitive as you need power hungry and expensive hardware to achieve.

​For context, a TetherBox Pico capable of recording 10 cameras will only be able to record 2 if transcoding (you can enable transcoding in TetherX by editing a camera and switching to the advanced tab).

Proxying & Packaging is what is used in most cases, where the original video stream is maintained but is packaged into different containers, for example .mp4 for video recording and .ts for local and high-def live streaming (see streaming technologies below).
​

This means that ultimately, you are at the mercy of the camera/recorder. If you need to open 16 cameras and each one is 1mbit, but your upload speed is only 10mbit, it will simply not work because the stream size cannot be adjusted without either:

Video vs Images

TetherX use a combination of images and video to achieve different goals. It is important to understand the differences and advantages/disadvantages of each, which in turn dictate when either is used in TetherX.

The main difference between image and video compression is every image is self contained, where every video frame is part of a stream. While you may skip an image, skipping a frame in a video stream leads to parts of the image breaking / disappearing:

Systems that ignore broken/skipped data (e.g. streaming over UDP) will show a broken image while many systems will simply show a loading spinner while they wait for the next key frame (which is controlled by the key-frame interval set on the camera/recorder, typically set to 1 second, or the same number as fps, but sometimes much longer).

Because each image is self contained, it is typically 5 to 25x larger in bitrate vs video at 25 images per second. It may initially seem obvious that video should be used when accessing remotely, however there are certain important underlying trade-offs that make it a much tougher question which needs to be evaluated on a case by case basis, according to the following:

Advantages of Images

Live View Streaming Technologies

TetherX uses all mainstream streaming technologies available and choses between them depending on the specific requirements and constraints:

How TetherX Does It

TetherX supports most streaming technologies and switches between them depending on context.

When local streaming (the TetherBox is able to detect if you are on the same network), if we are viewing less than 10 cameras simultaneously TetherX switches to LHLS (see above) to show the primary video stream from each camera at full resolution/frame-rate (assuming your viewing device is capable of displaying this many streams). If this is not working well for you, you are presented with a toggle to switch off High-def streaming to fall back to loading images.

When full screening a camera (double tap/click a camera), we assume you want the higher quality and we switch to the full primary stream. If your connection is not able to sustain this stream, we automatically fall back to loading images.

When viewing multiple sites / cameras over Internet in record mode, we switch to image viewing but we transcode/transize the images depending on the size of each live view box on your screen. This ensures that you are able to view many simultaneous cameras, the latency is lower than video, it automatically adapts to the available bandwidth and it does not impact recording quality. This does however mean a lower fps.

When viewing multiple sites / cameras over Internet in monitor mode, we proxy the connection directly to the image provided by the camera. This leads to a further lowering of fps but ensures the TetherBox can monitor the health of and provide live view of 10x more cameras than in record mode.

Learn more about using Live View in TetherX here.

How Hikvision iVMS Does it

Because of the constrains outlined above, in order to show smooth video in iVMS (and Dahua PSS) software, if the connection speeds both on site and viewing device cannot accommodate the streams, the software temporarily reconfigures the cameras to send a lower bitrate stream while keeping the resolution the same.

💡 Note: if you happen to kill the software at this point (or lose connection), this can cause the camera to permanently record in lower quality.

Because many cameras or recorders only support a single stream at above D1 resolution, this means that not only is the live view quality reduced, but also the video being recoded which can lead to losing critical video evidence.

In our testing, limiting the connection to 5mbit 200ms upload and streaming just 4 cameras in HD resulted in blocky and usable footage being recorded on the NVR. It also took over 10 seconds to get an initial image, however the motion was smooth (25fps) once loaded.

In comparison when using images (outside of the iVMS/PSS software), the images loaded almost immediately, the image quality was significantly higher, but the frame-rate was poor (3-4fps) – still sufficient for making decisions in a control room setting, but understandably disappointing in smoothness by comparison. (Note: higher fps can still be achieved by full screening a single camera on demand).

When viewing a smaller number of cameras from the same manufacturer on a single PC or phone, it looks impressive to have smooth 25fps video on iVMS/PSS/others. However, when dealing with 100+ or even 32 cameras, from different manufacturers, different firmware versions, with multiple users, across multiple sites, with differing and fluctuating bandwidths, you begin to appreciate the trade-offs and advantages/disadvantages of each approach.

💡 Note: This approach of custom code to adjust Hikvision camera settings to achieve smoother live view is only suitable if you do not care about recording quality and you are optimising for a single manufacturer with compatible models/firmware.

​TetherX is an open platform with a focus on convention over configuration, we prioritise the integrity of recorded footage above live view and we implement approaches that work across all recorders/cameras as well as viewing devices.

.

Uniview / UNV Camera Setup Guide (for use with TetherX)

Using TetherX with Uniview / UNV Cameras

Summary

Uniview or UNV cameras should work out of the box in most cases. However please note depending on the age of the camera and firmware versions, the RTSP path may be different.

Please try the following paths:

3. Open the Advanced tab and enter the required Analytics Path and Recording Path. Please try all the paths given as examples above.

.

Camera Setup Checklist

Adding IP cameras to TetherX Please note your camera may have a different interface and options may be located in a different part of the interface. Please refer to the camera manual if you are not able to find the relevant option.

Network

Set a Static IP

Set camera to unused IP on 192.168.88.x network
set DNS/Gateway to 192.168.88.100

Important: Although it’s possible to configure your camera with DHCP, and TetherBox is capable of detecting any IP changes, we strongly advise against this practice for security reasons. This setting can potentially allow the camera to connect directly to the internet, raising a range of security issues. These include unauthorised access through back doors, or the risk of security holes in the camera’s firmware if it’s not updated regularly.

Video & Audio

Recording Stream (primary)

Analytics Stream (secondary)

Conditions

.

Audio (optional)

Date & Time

One option is to disable time from being displayed in the camera at all. You generally do this under OSD settings. If you do wish time to be displayed in the image, you need to set the following:

<p>The post TetherX Camera Setup Guide v2 first appeared on NVR IPCAMERA SECURITY.</p>

How to Change the Password on a 5.0 UI IP Camera

.

IPCamera/Change Password 5.0 UI

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the current username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the System option from the drop-down list

3. Select Account on the left.
Then select the User tab at the top.
Click on the Edit (Pencil) icon to the right of the user account who’s password you want to edit

4. Enable the Change Password slider.
Then enter the current password in the Old Password field.
Enter the new password you want to change it to in both the New Password and Confirm Password fields.
Click on OK at the bottom

5. Once the new password is successfully changed, you will see “Modify User Succeeded” at the top

Dahua IP Camera 5.0 UI Setup

How to Set the Date and Time on a 5.0 UI IP Camera

.

IPCamera/Set Date and Time 5.0 UI

Description

This guide will show you how to set the Date and Time on a IMaxCamPro IP Camera with the 5.0 User Interface

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the System option from the drop-down list

3. Select General on the left.
Then select the Date & Time tab at the top.
To set the date and time without an NTP server, select Manual Setting. Then adjust the Time, Time Format, and Time Zone. (You can press Sync PC if you want to pull the time from the PC you are using. The Time Zone still needs to be set manually though.)

To set the date and time with an NTP server, select NTP. Then fill in the information for a functioning NTP server. (This will only work if the camera has access to the internet.)
For locations that use Daylight Saving Time, enable the slider below DST and select the dates and times that Daylight Savings starts and stops.
When you are done adjusting settings, select Apply at the bottom to save the settings.

How to Set the IP to Static on a 5.0 UI IP Camera

.

IPCamera/Set IP to Static 5.0 UI

How to Set IP Settings to Static on a 5.0 UI IP Camera

Description

This guide will show you how to set the IP settings to static on a ImaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the Network option from the drop-down list

3. Select TCP/IP on the left.
Click on Static next to “Mode”.
Then fill in the IP Address, Subnet Mask, Default Gateway, and DNS settings below that. (You can press the “Test” button if you want to see if that IP address is free on your network.)
When you are done adjusting settings, click on Apply at the bottom

How to Configure Recording to an SD Card on a 5.0 UI IP Camera

.

IPCamera/Configure Recording SD Card 5.0. UI

How to Configure Recording to an SD Card on a 5.0 UI IP Camera

Description

This guide will show you how to configure recording to an SD Card on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the Storage option from the drop-down list

3. Select the SD card from the list by enabling the radio button on the left.
Click on Format at the top to wipe all the data on the SD card and configure it for recording on this camera.

4. Click on the Home icon at the top left.
Select Record. (If you don’t see it on the main page, click the right circle at the bottom to switch pages.)

5. Select the Record Control tab at the top.
Adjust the settings on this page as desired:

When you are done adjusting settings, click on Apply to save the settings

6. Select the Time Plan tab at the top.
Adjust each Event Type on the weekly calendar.
When you are done adjusing the schedules, click on Apply to save your changes

7. Select the Storage tab at the top.
Adjust the settings on this page as desired:

When you are done adjusting settings, click on Apply to save the settings

How to Playback Video from an SD Card on a 5.0 UI IP Camera

.

IPCamera/Playback Recording SD Card 5.0. UI

How to Playback Video from an SD Card on a 5.0 UI IP Camera

Description

This guide will show you how to view recorded video footage from an SD Card on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Click on the Home icon at the top left.
Select Record. (If you don’t see it on the main page, click the right circle at the bottom to switch pages.)

3. Select the Search Video tab at the top.
Select the start date and time, and the end date and time on the left.
Then click Search below that.
All the recorded footage on the SD card in the time range will appear.
Double-click on the specific clip you want to play

4. Move the slider at the bottom to adjust the playback time.
Use the controls to play, pause, rewind, fast forward, or jump between clips

IPCamera/Password Reset 5.0. UI

.

IPCamera/Password Reset 5.0. UI

How to Reset the Password on a 5.0 UI IP Camera

Description

This guide will show you how to reset the password on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

Reset via Password Recovery in DMSS

1. Input the camera’s IP address into a web browser.
Click on Forgot password?

2. Click on OK to agree to use your email address in this process

3. If you setup a recovery email you will be brought to a page with a QR code on it. (If you didn’t setup a recovery email, skip to “Reset via Physical Button” at the bottom of this page.)

4. Open the DMSS app on a mobile device.
Tap on Me at the bottom.
Then select Tool Manager

5. Tap on Device Password Management

6. Use the mobile device’s camera to scan the QR code from Step 3 above

7. Once the QR Code has been successfully scanned you will see the following message

8. Check the email inbox for the email address that was registered for password recovery on this device.
Input the security code from that email in the Security code field.
Then click on Next

9. Enter a new password in the New Password and Confirm Password fields.
Then click on OK

10. The password will be successfully reset

Reset via Physical Button

Depending on the model of your IP Camera, there could be a physical reset button on the outside body of the camera, or inside the camera body.

1. Reset: Press the reset button for 10-20 seconds while the camera is connected to power.

IP Camera Basic Info

Important Safeguards and Warnings

1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The product must be grounded to reduce the risk of electric shock. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.

2．Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.

3．Installation

4．Qualified engineers needed All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment The NVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. This series product shall be transported, storage and used in the specified environments.

6. Accessories Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package.

7. Lithium battery Improper battery use may result in fire, explosion, or personal injury! When replace the battery, please make sure you are using the same model! Before your operation please read the following instructions carefully.

Hardware Installation and Connection

Note: All the installation and operations here should conform to your local electric safety rules.

1. Check Unpacked NVR When you receive the NVR from the forwarding agent, please check whether there is any visible damage. The protective materials used for the package of the NVR can protect most accidental clashes during transportation. Then you can open the box to check the accessories. Please check the items in accordance with the list (Remote control is optional). Finally you can remove the protective film of the NVR.

2. About Front Panel and Rear Panel For detailed information of the function keys in the front panel and the ports in the rear panel, please refer to the User’s Manual included in the resource CD. The model label in the front panel is very important; please check according to your purchase order. The label in the rear panel is very important too. Usually we need you to represent the serial number when we provide the service after sales.

3. After Remove the Chassis Please check the data cable, power cable, COM cable and main boar cable connection is secure or not.

4. Important：Please turn off the power before you replace the HDD. You can refer to the User’s Manual for recommended HDD brand. Please use HDD of 7200rpm or higher. Usually we do not recommend a PC HDD. For detailed operation instruction, please refer to the User’s Manual included in the resources CD.

1. Use the screwdriver to loose the screws of the rear panel and then remove the front cover.

2. Put the HDD to the HDD bracket in the chassis and then line up the four screws to the four holes in the HDD. Use the screwdriver to fix the screws firmly to secure HDD on the HDD bracket

3. Connect to the HDD data cable to the main board and the HDD port respectively. Loosen the power cable of the chassis and connect another end of the power cable to the HDD port.

4. After connect the cable, put the front cover back to the device and then fix screws of the rear panel.

<p>The post Dahua IP Camera 5.0 UI Setup first appeared on NVR IPCAMERA SECURITY.</p>