How to add a Hikvision NVR to Hik-Connect

Before you start…​

Part 1: Enable Hik-Connect on the NVR…​

.

.

.

.

Part 2: Set up Hik-Connect on your mobile phone or tablet…​

.

.

.

Part 3: Add the NVR to your Hik-Connect account…​

.

.

.

Other tips…​

Guides for Hikvision NVRs with V5 firmware

How to set up motion detection and alerts on a Hikvision NVR

What is Motion Detection and why is it useful?​

Motion detection is one of the easiest events to set up and will notify you as soon as a person or vehicle enters a predefined detection zone in your scene. Traditionally, it would just rely on lots of pixels changing between frames in your camera’s video stream, which would indicate movement in the scene.

Of course, this would cause lots of alerts for things you are not interested in, such as animals, moving plants and rain. Hikvision’s Acusense cameras and NVRs now have something called Motion Detection 2.0, which cuts the false-positive detections right down as will only notify you when people and/or vehicles are in the scene by learning what they look like. In this simple step-by-step guide, we will show you how to get motion detection set up on the new NVR 5.0 web interface.

Step 1: Go to your NVR’s Motion Detection configuration page…​

Step 2: Configure your Motion Detection zone and rules…​

​

Quick tip…​

If you find that the camera preview is too small when drawing your detection zones, you can switch the view to full screen by clicking on the Full screen (four arrows) button in the toolbar, and then exit full screen by pressing Esc on your keyboard.​

Step 3: Set the arming schedule to specify when you want Motion Detection active…​

​

Quick tip…​

If the 30-minute segments are not precise enough for you, you can finely tune a period of arming or disarming by double-clicking on the segments and specifying your start and end times in minutes using the arrows.​

​

Step 4: Set what you need the NVR to do when a camera detects a target…​

How to connect an IP camera to a Hikvision NVR

Adding cameras to your Network Video Recorder (NVR) is a crucial step in any CCTV setup. Not only does it allow you to store and access all your camera recordings in one place, but it also simplifies camera configuration. In this simple step-by-step guide, we’ll show you how to add cameras to a Hikvision NVR using the new NVR 5 web interface.

.

Why add cameras to an NVR?​

.

Before you start…​

Before anything, to be able to add your IP cameras, you need to make sure that:
.

.

How to add your cameras using the V5 GUI…​

Step 1:​

Open a web browser and enter the IP address of your NVR in the address bar. If you are not sure what this is, use the SADP tool to find it.​

Step 2:​

Log in to the NVR using the “admin” username and password you have set on it.​

​

Step 3:​

Go to: Device Access > Device Configuration > PoE Settings​

​

If you are connecting your camera via the Plug-and-Play method, then make sure that Network Camera Plug-and-Play is enabled on the POE port you will be connecting the camera to on this page.​

​

For any camera with a cable run under 100m, leave the Network Cable Distance as Short Distance.​

​

If you are connecting your camera manually by IP address, disable the Network Camera Plug-and-Play option for the channel that you plan to add the camera to.​

Step 4:​

Go to: Device Access > Device > Video Device​

​

For any Plug-and-Play camera, just make sure that it is in its inactive default state and then connect it to the port you reserved in step 3. After 20 seconds or so, the camera Status should turn to Connecting and then Online (you may need to click on Refresh to see this).​

​

For Manually added cameras, if you can see the camera in the List of Online Devices section, then just tick the box for the camera and then click + Add to Device List, which will then automatically add it to one of the channels you disabled Plug-and-Play on in the last step.​

Alternatively…​

Click on +Add at the top of the page and fill out the fields as follows:​

​

IP Address: Enter the IP address of your camera, using the ‘Test’ button to verify there is a camera at that address. ​

Device Name: This can be anything you like, as it is the name the camera will show with on your NVR. ​

Protocol: Select the camera’s manufacturer from this list, or failing that, use the ONVIF protocol (your camera will need to have ONVIF enabled for this to work). ​

Management Port: Enter the Server port set on the camera, which you can find in the SADP tool or in Network>Basic Settings>Port in the camera’s web browser interface. If you haven’t changed this, it is usually 8000 by default. ​

User Name: “admin” or the username of any other users set up on that camera. ​

Password: The password set with that user on the camera – if this is the same as the ‘Default Activation Password‘ you have set on the NVR, then you can tick this box instead. ​

Transfer Protocol: ‘Auto’ is normally best. ​

​

When these are completed, click OK.​

​

Your camera should then appear in the list of devices with an assigned channel, and an Online status, meaning it has been successfully added.​

.

Extra tips…​

Source : https://www.use-ip.co.uk/forum/forums/guides-for-nvrs-with-v5-firmware.71/

.

<p>The post Guides for Hikvision NVRs with V5 firmware first appeared on NVR IPCAMERA SECURITY.</p>

Intro

You’re Not Alone

Installation can be hard. We’re happy to talk it over with you or take over a DIY project that you’ve realized needs professional installation. Our support hours are from 9AM-7PM Monday – Friday (EST) and we are available via chat, email, phones, and remote PC screen-sharing, if you need any help. You can reach us at 866-414-2553.

Disclaimer: The laws governing cable and wire installation can vary from state to state and sometimes even counties and cities pass specific, unique laws regarding cabling; these state, county and city laws are too complex for us to explain. This page is not a how-to installation guide, as we cannot keep up with local laws.

Although we now offer installation, locally, we started as a DIY-only company, and we primarily serve those adventurous types who want to run the cable for themselves. Even so, we get asked about do-it-yourself installation all the time…. We wanted to post a few of our standard answers here.

Part 1

Don’t Start a Fire or Shock Yourself

Electricity Can Kill You; Avoid Electrical Lines!

Never strap, staple or otherwise run networking cable to conduit or raceways carrying electrical current. Never run any cable within 2 inches of Class I electrical lines, lighting, fire alarm, or power lines or devices.

Give a Wide Berth to High Voltage Devices or Lines

Never run any cable within 6 feet of a conductor or fuse box. A minimum 5-inch distance is required from any fluorescent lighting fixture or power line over 2 kVA and up to 24 inches from any power line over 5 kVA. If unsure about the a device or line, consult an electrician. Route cable away as far as you can from large motors, generators, induction heaters, arc welders, x-ray equipment, and radio frequency, microwave or radar sources. NEC/NFPA 70, Article 800-52

Protect it from Future Physical Damage

You might want to put a nail or screw in later and don’t want to puncture your cables, so when a cable, raceway, or soft conduit (anything you can puncture) is installed parallel to framing members (joists, rafters, or studs), furring strips, or crown molding, keep the cable at least 32 mm (1.26 inches) from the edge. NEC 300.4(D)

Don’t Leave it Dangling – Secure Your Cables

You can connect cable directly to a surface with straps, staples, cable ties, hangers, or similar fittings, but you have to secure it somehow. NEC 800.24; 300.11

Use Plenum rated cable in Areas with Airflow

If you are going to run cables through an area which is used by your heating, air circulation, or air conditioner systems (such as above a drop ceiling in an office), you must use Plenum rated cables, which have a special insulation that has low smoke and low flame characteristics. When securing cable in Plenum required areas, make sure your straps, cable ties, and similar fittings also are plenum rated. NEC 830; NFPA 90A

National Rules – Consult your local laws

These guides are meant to familiarize our clients with the national requirements as expressed in the National Fire and Alarm Signaling Code and the National Electrical Code. Your state or local laws may differ. If you live outside the USA, consult your governmental laws. Don’t consider this your only resource.

Turn the Breaker Power OFF

Any time that you will be drilling or cutting into your wall, you want to turn the power off. You don’t want to drill into a hidden electrical line. You probably already know this, but our lawyers insisted.

Wear Safety Goggles

Any time that you are drilling, you want to wear safety goggles and hearing protection, like ear plugs.

Security Camera Installation Guides v2

Part 2

Drilling through Different Materials

Sheetrock (most interior walls)

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of sheetrock.

Wood

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of wood.

Stucco

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of stucco.

Brick and Masonry

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of brick.

Concrete

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of concrete.

Metal Siding

A list of tools necessary, step-by-step instructions for installing SCW cameras, and how to close up the hole when drilling into a surface made of metal siding

Part 3

Running the Cable

Basic Cabling

Terminating Cable (Putting the ends on)

Instructions for putting the RJ45 ends on to ethernet (for example, Cat5 / Cat6 / Cat5e) cable.

Using Our Waterproof Connectors

When installing a camera outdoors, it is imperative that you put our waterproof RJ45 Connector on the ethernet (for example, Cat5 / Cat6 / Cat5e) cable.

No Protection – Just Running the Wire

You can connect cable directly to a surface with straps, staples, cable ties, hangers, or similar fittings, but the cable could get damaged and someone might be able to cut it.

24 Volt Wiring: PTZ

The Spotlight PTZ cameras uses 24 volt power rather than POE because it requires more power than is capable of Power-Over-Ethernet for its natural white light spotlight. The Laser can also be powered via 24 volt power and can be powered the same way, although it is not required to do so. This guide shows you how to wire these PTZs.

24 Volt Wiring: Sharpshooter

The Sharpshooter IP Bullet cameras uses 24 volt power rather than POE because it requires more power than is capable of Power-Over-Ethernet for its long range infrared. This guide shows you how to wire the Sharpshooter.

Protecting your Cabling

Liquidtight Plastic Tubing

Liquidtight plastic tubing is easier to work with than flexible metal tubing, but is less secure. It is also great for areas with lots of expected moisture as it won’t rust.

Flexible Metal Conduit (FMC)

Flexible metal conduit is difficult to cut (watch out for sharp edges), but easier than solid conduit to install.

Electric Metal Tubing (EMT)

Solid metal conduit is the most secure form of installation. It requires a specialty conduit bending tool.

Conduit Fill

This chart will let you know how many cable runs you can fit in one conduit pipe, depending on the size of the conduit.

Raceway (Outdoors) – Coming Soon

Raceways are most popular indoors to make the space look clean and professional. There are also outdoor rated raceways; this guide covers using raceways outdoors.

Clean and Professional Interiors

Raceway (Indoors)

Raceways are most popular indoors to make the space look clean and professional. There are also outdoor rated raceways. This guide covers using raceways indoors.

Ethernet Wall Plates

Not recommended. It can be difficult to find a wall plate that passes POE power and provides grounding. These devices also provide a secondary point of failure, and take up far more room than a cable pass through plate for larger systems.

Dealing with Long Distance

Using POE switches to reduce cabling

You can run one cable to a POE switch and then run several cameras to that switch, however, POE switches are not plug-n-play. POE switches do require you to know a decent amount about computer networking.

Cables run over 300 feet

Cat5e and Cat6 cable data has a limit of 300 feet, but if you need to go further than that you can use a POE extender, POE injector, or POE switch to hear and repeat the signal. This article discusses when you would use each of these tools.

Long Distance Wireless

Military-Grade Long-Range Wifi Solution are used when attempting to send wireless IP Camera video data more than 100 feet (and up to 3 Miles). These products will require a professional wireless network technician on location.

Part 4

Mounting Cameras and Recorders

Basic Camera Installation

Bullet Cameras on Walls

In this guide, we will be installing a bullet camera on a wall.

Bullet Cameras on Ceilings

In this guide, we will be installing a bullet camera on a ceiling.

Bullet Cameras on Soffits

In this guide, we will be installing a bullet camera on a soffit.

Dome Cameras on Ceilings

In this guide, we will be installing a dome camera in a ceiling tile.

Dome Cameras on Walls

In this guide, we will be installing a dome camera on a wall.

Positioning the Lens in our Dome Cameras

In this video guide, we demonstrate how to adjust the lens positioning on our Marshall, Guardian, Warden, and Mosquito Dome Cameras.

Audio and Alarm Inputs FAQ and Sample Wiring Guide

Here’s a guide on Line-Level Audio Inputs and Analog Wired Alarm Integration.

Attaching Our Camera Mounting Accessories

Electrical Mounting Boxes

Our electrical box mounts are used to give easy access to your connections, hide them inside the junction box, and allow you to drill a smaller hole in your wall. If you want to run conduit they are necessary to run conduit straight to the camera.

PTZ Wall Mount Bracket

This guide will show you how to mount your PTZ camera to the wall mount bracket.

Pole Mounts

In this guide, we will be installing a Hornet Pro bullet camera on a pole.

Pendant Mounts

In this guide, we will be installing a Radius panoramic dome camera on a pendant mount. You can install all our PTZ and a few of our dome cameras via Pendant mounts.

Screw Size Chart

Lose a screw? No problem. Here’s all our 2018 product line screw sizes in one convenient place.

NVR Mounting Options and Hard Drive Installation

Shelf / Desk Mounting NVRs

This is what most people do: just put it on a shelf or desk. This makes it easy to connect to a TV/monitor and use the mouse (included) to control the NVR.

Rack Mounting NVRs

Companies often want to put the NVR in their server rack room. People who do this often to control the NVR only through our apps or web browser. Only our larger NVRs (16 channels and up) are wide enough to be rack mounted (and they come with ears). Our smaller NVRs can use our Rack Mount Shelf.

Wall Mounting NVRs

Many people choose to mount their NVR on a wall near a TV. To do this, you will want to purchase a vertical rack, like this one that matches the height of your NVR. The 16, 32, and 64 channels units have a height of 2U and the 128 channel is 3U. NVRs are heavy and you will want to make sure your wall can support the weight.

Mounting NVRs behind a Wall / in an Attic

People who are afraid of the theft of an NVR often place it behind a false wall or in an attic. People who do this control the NVR only through our apps or web browser. Be aware: Not all attics are insulated well enough to be within the temperature requirements of the NVR. Temperature range is listed on each NVR’s technical specs tab.

“NVR” Lock Boxes

There’s a few companies advertising “NVR Lock Boxes,” but any Server Rack or Computer Rack will do. Most Server Racks or Mounts have locks on them already. This picture is of a Tripp Lite Server Rack with Lock It houses a 32 channel NVR, two of our POE Switches, and a router, but there are tons of companies selling small server racks online.

NVR hard drive installation

If you purchase both a hard drive(s) and recorder from us, we will happily install the hard drive for you. but here’s a handy guide if you want to do it yourself.

Part 5: Specialized Work

When to NOT DIY – Get an Expert

Long Distance Wireless

Military-Grade Long-Range Wifi Solution are used when attempting to send wireless IP Camera video data more than 100 feet (and up to 3 Miles). These products will require a professional wireless network technician on location. We can’t offer support on this product remotely, as once we can see it remotely, that means that it is already working.

Aerial Cable

Aerial cable clearance varies based on location (cable over a road needs more clearance than over a sidewalk, for example), needs to be enclosed within 8 feet of finished grade, and requires a on-site structural analysis to make sure the cable won’t break. Hire an expert.

Burial of Cable

Number one, call 811 before you ever dig: know where your power company has buried its power cables! The required cable burying depth also can vary based on your local zoning laws and your certificate of occupancy; you should get an expert.

Elevators

Don’t even try to install any cable in one without a licensed elevator technician’s help as the cable needs to be inside the cable traveler. An error in securing the cable can result in damage to the elevator’s operation – and potentially the people inside it. Don’t mess with it; get a licensed elevator technician to run the cable.

<p>The post Security Camera Installation Guides v2 first appeared on NVR IPCAMERA SECURITY.</p>

I spent the last two weeks getting to know everything about these cameras and this thread will capture all this information. It will take me several weeks to document all the information so please be patient.

There are a variety of problems that I will try my best to explain and share the possible solutions. I have gotten pretty comfortable with these cameras and have purposely bricked them to various degrees of severity just to validate the recovery process. Most people “brick” their cameras trying to upgrade the firmware. This is not a serious issue and it can be corrected very easily. The camera runs an upgrade service on port 3800. The configTool always shows a default port of 37777 but this is not an issue as it can do the upgrade on port 3800 anyway. Change your port to 3800 and use a firmware file lsted below and you are back in business.

I will keep updating this post as I get more time to write all the details around recovery. I will also post links to over 40+ firmware files that and which cameras they will work with. It will take me a bit of time to capture all this information, so please be patient.

 How to Download and Prepare Firmware

This guide will show how to download and prepare the firmware file for a Dahua device.

Firmware files for Dahua devices can be found at Firmware by Device or the specific product page for the device

Firmware is typical provided in a ZIP file, a compressed file format

This file will contain the actual firmware file, which needs to be extracted from the ZIP file in preparation for the upgrade

Prerequisites

Video Instructions

Step by Step Instructions

Confirm the Model and current firmware of Dahua device

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Info

3. Click Version

The Device Type will be displayed

The current System Version will be displayed

Download the firmware file for device from DahuaWiki

4. In a browser go to DahuaWiki.com

Under Specifications, Firmware, & Manuals

Click the device type (in this example Recorder)

5. Enter the device model into the field

6. The results will be filtered

7. Click the firmware icon to download the firmware file

8. The file will download

Extract the firmware file to local computer

9. Right click the Start Menu / Windows icon in the bottom left of the screen

Select File Explorer

10. Select Desktop

11. Click Home

Then click New folder to create a new folder to extract the contents of the firmware zip file

12. Find the created folder in the list, double click to open

13. Under the Downloads window of the browser, click ‘Show in folder’

A new File Explorer window should open containing the directory the firmware zip was downloaded to

Locate the file in the list

14. Right click

Select Cut

15. Select the window with the new directory

Right click in the window

Select Paste

The folder will appear in the directory

16. Right click the file

17. The contents of the zip file will appear in a new window

18. Click to select all files in the folder

Drag and drop the files to the created folder

The files will appear in the directory

The firmware file will appear in the directory ready to use

Unbricking your Dahua IP camera (Tips, Tricks & Firmware)

BRICKED CAMERA? How can you tell?

There are several types of “BRICKED” camera conditions and they have varying levels of severity and also varying levels of complexity for recovery. Most are simple and caused by bad firmware uploads. The worst will require a full rebuild of the partitions which load the kernel, software and all other data.

1. The first step in identifying the severity of your issue is to determine what still working on your camera. In order to do that, lets remove as many variables as possible to the troubleshooting process. If possible, connect the camera ethernet and PC ethernet on it’s own switch and make sure that no vlan tagging is enabled on the switch.

Next, you need to figure out if the IP address is still reacheable. Ping the last known ip address. The default address for most cameras is 192.168.1.108.

If you don’t know it you can use the arp/ping method to configure which adds as startic arp entry to a new ip address. (This feature is enabled on the camera by default)

2. Once you have a pingable IP, you need to know what services are still active on the camera. This can be done with a simple port scanner. I have added a link to below in tools.

3. Run the port scanner and record which ports are still open. In many cases port 23 and port 3800 will still be open. If this is your situation, it is a very simple fix. If no ports are open, you will need to do a full image load which is more complex.

The typical ports that you would see are:

23 – Telnet access

80 – Web User interface

443 – SSL

554 – Real time streaming port

3800 – Upgrade Deamon

5000 – UPnP

37777 – TCP Video streaming

37778 – UDP Video Streaming

42323 – Real time remote runner

Plus a whole bunch more of UDP ports and more TCP ports

REPAIR WITH PORT 3800

Download a step by step guide (DAHUA IP Camera Recovery v1.0.pdf) with screen prints @ http://tinyurl.com/lbl3up7

1A. If port 3800 is open you can connect with the Dahua Config tool (link below in tools). I tdefault to port 37777 but change it to 3800 as this port where the upgrade daemon is listening. Port 37777 is a redirect but it won’t work if your firmware has failed.

Launch the config tool and click on login button. Type the IP address , username and password then port 3800.

Open a know working firmware file and upload to the camera.

1B. If port 3800 is not open, go to the next step to enable port 3800.

2. If you have telnet access, you can login with putty. Link to putty below in tools. The default Web UI password is admin / admin.

In older firmware the telnet account is root / vizxv

In newer firmware the telnet account is admin / 7ujMko0+”web UI password” —> 7ujmko0admin

Once connected you can execute a ps command to see running processes. /usr/sbin/upgraded process is what listens on port 3800 for the firmware binary file.

There is also another copy in /var/tmp/

A useful tip for watching the upgrade process is to kill the “upgraded” process that is running and re-launch it in the foreground to watch the upgrade.

~#>ps

625 root 0:00 [mtdblock3]

630 root 0:00 [mtdblock4]

635 root 0:00 [mtdblock5]

772 root 0:00 [ubi_bgt7d]

776 root 0:00 [ubifs_bgt7_0]

790 root 0:00 /sbin/telnetd

798 root 0:00 [OSA_796_1]

860 root 0:00 syshelper elper 60

861 root 0:00 /usr/sbin/upgraded

869 root 0:00 [dsplogd]

870 root 0:00 [encode_guard]

889 root 0:00 [flush-ubifs_6_0]

923 root 3:29 ./VideoDaemon AEWB AF TVOUT

~#> kill -9 861

~#> /usr/sbin/upgraded

22:52:46|[crypt] crypt_open ok!

Name: upgraded, bulid date: Apr 19 2014 09:17:58, svn: 255

Fail to get env authcode!

@@@@ buf = PZC4MU056W00XXX

22:52:52|[pdc] WARN (MISC_ioctl|493): Get SdCard cfg failed !

UPGRADED_MSG: Can’t Open /mnt/mtd/Config/passwd

UPGRADED_MSG: Login success!

UPGRADED_MSG: Kill 976 successful

UPGRADED_MSG: reset_watchdog

UPGRADED_MSG: Receive A4(alarm)

UPGRADED_MSG: reset_watchdog

UPGRADED_MSG: Receive A1(alive package)

UPGRADED_MSG: reset_watchdog

UPGRADED_MSG: Received : 29868252, FileSize : 29868252

UPGRADED_MSG: Download Complete

UPGRADED_MSG: DoDownLoad success!

UPGRADED_MSG: Flash init success

UPGRADED_MSG: hwid file success!

Fail to get env native!

UPGRADED_ERR: LINE: 1074: invalid file: Install.lua

UPGRADED_MSG: zip file total size: 40900220

Fail to get env authcode!

@@@@ buf = PZC4MU056W00XXX

22:53:10|[pdc] WARN (MISC_ioctl|493): Get SdCard cfg failed !

UPGRADED_MSG: packet.name: SD6XXX, board.name: IPC-HFW4300S-V2

UPGRADED_MSG: packet.hardver: , board.hardver:

UPGRADED_MSG: packet.name: IPC-HX3XXX, board.name: IPC-HFW4300S-V2

UPGRADED_MSG: packet.hardver: , board.hardver:

UPGRADED_MSG: Verify version success

Header CRC Checking … OK

Image Name: kernel.img

Image Type: kernel.img (gzip compressed)

Data Size: 2546876 B, Bytes = 2.43 MB

Load Address: 0XC80000

Data CRC Checking … OK

Programing start at: 0XC80000

<5>UBIFS: un-mount UBI device 2, volume 0

<5>UBIFS: un-mount UBI device 4, volume 0

Upgrade : Complete Total 6%…

Header CRC Checking … OK

Image Name: partition-x.cramfs.img

Image Type: partition-x.cramfs.img (gzip compressed)

Data Size: 4160 B, Bytes = 0.00 MB

Load Address: 0X500000

Data CRC Checking … OK

Programing start at: 0X500000

Upgrade : Complete Total 6%…

Header CRC Checking … OK

Image Name: romfs-x.ubifs.img

Image Type: romfs-x.ubifs.img (gzip compressed)

Data Size: 7340096 B, Bytes = 7.00 MB

Load Address: 0X1200000

Data CRC Checking … OK

Programing start at: 0X1200000

Upgrade : Complete Total 24%…

Header CRC Checking … OK

Image Name: pd-x.ubifs.img

Image Type: pd-x.ubifs.img (gzip compressed)

Data Size: 1966144 B, Bytes = 1.88 MB

Load Address: 0X940000

Data CRC Checking … OK

Programing start at: 0X940000

Upgrade : Complete Total 28%…

Header CRC Checking … OK

Image Name: user-x.ubifs.img

Image Type: user-x.ubifs.img (gzip compressed)

Data Size: 21233728 B, Bytes = 20.25 MB

Load Address: 0X2200000

Data CRC Checking … OK

Programing start at: 0X2200000

Upgrade : Complete Total 80%…

Header CRC Checking … OK

Image Name: custom-x.ubifs.img

Image Type: custom-x.ubifs.img (gzip compressed)

Data Size: 1966144 B, Bytes = 1.88 MB

Load Address: 0X600000

Data CRC Checking … OK

Programing start at: 0X600000

Upgrade : Complete Total 85%…

Header CRC Checking … OK

Image Name: web-x.ubifs.img

Image Type: web-x.ubifs.img (gzip compressed)

Data Size: 5505088 B, Bytes = 5.25 MB

Load Address: 0X1A00000

Data CRC Checking … OK

Programing start at: 0X1A00000

Upgrade : Complete Total 99%… [libpdi] Read: blkIndex: 0,pageIndex: 1,byteIndex: 0 ,fLag: ff

Upgrade : Complete Total 100%… UPGRADED_MSG: will reboot system

Here you can see each partition being loaded wit the individual img files. I will write a quick how to on loading each one individually at a later time.

If you chose a valid firmware file, you will be back in working order. If you still have problems, repeat with another firmware file till you have a valid file. The IPC-HFW4300S-V2 is not natively compatible with all other 4300S firmware. I am in the process of writing a how to that explains how to over come this issue.

UNBRICK WITH UBOOT via SERIAL

NOTE: This section is coming soon… I’m gathering all the images I need for various camera types

OTHER USEFUL INFORMATION (to be sorted later)

The firmware consists of several images that are loaded into various partitions in flash in a UBI file system. You can load each partition separately if needed. More on this later…. (I’ll put a guide together on flashing and recovering partitions)

Once you telnet into the camera, there are number of useful binaries in the user shell that can help correct and diagnose some of the problems people are experiencing. One of the helpful steps is to kill the /var/tmp/upgraded process and run it in the foreground so you can see what is going on and easily capture error messaged. The /var/tmp/upgraded process is what opens the port 3800 and allows you to connect to the camera with the config tool if your web services have failed. There is also another copy in usr/sbin/.

Also, in there is a command to reset all the parameters back to factory defaults (username, password, ip address back to 192.168.1.108 etc.) This can be accomplished with /sbin/clearparam.

Another issue that people run into is the constant reboot issue. This can be caused by a failed process. The main application which provides all the camera capabilities (web interface, streaming, etc.) is /usr/bin/sonia. This process is what makes most firmware different from version to version (sort of). There are also changes to the web partition which contains the web server pages that /usr/bin sonia hosts on port 80. The sonia process is invoked by a shell script in init.d and if the process is killed, the camera reboots after a few minutes. This has cause many people issues when trying to “unbrick” the camera since you only have a few minutes between reboots.

To stop the reboots you can update the flash. There is a parameter called appauto that tells the camera to auto start /us/bin/sonia. If you want the camera to start and not invoke the shell script that launches sonia, you need to set appauto to 0. This will stop the camera from rebooting when sonia is not running.

This cam be accomplished by running ‘/sbin/appauto 0’. To turn it back on, just run /sbin/appauto 1. This writes the boot parameter in flash that the kernel reads before starting the process. You can check the current status of the appauto bootparameter with ‘cat /proc/dahua/bootpara’ It will only show what the parameter was when you booted up, so if you changes it you need to reboot to see the change in /proc/dahua/bootpara.

Realtime streaming URL – rtsp://192.168.1.108/cam/realmonitor?channel=1&subtype=0&proto=Onvif

You can change the subtype to 1 for the secondary stream also you can add user:password@ in front of the IP address if you have the permissions set requiring it.

You can use the HTTP API to configure some parameters that are not yet in the web UI. For instance, another member discovered he could enable NFS through the web UI in addition to the local SD card. This config is not possible through the web interface as you need to pick one or the other.

These documents details the API of Dahua video products (links provided to some of the versions below). Programmers or users can access and configure Dahua video products through the API. Every setting of the camera is available through the API whereas only a small number are available through the WEB interface. The document with version 1.10 is available with firmware version 2.0 and above. This document with version 1.20, 1.21, 1.22, 1.23,1.24,1,25,1,26,1,27,1,28 is available with firmware 2.210 and above.This document with version 1. 29 ,1.30, 1.31, 1.32, 1.33, 1.34, 1.35,

1.36 is available with firmware 2.210 and above.This document with version 1.37 is available with firmware 2.212, 2.4 and above.

I have also done a bit of testing around the tftp process that is invoked in u-boot that looks for upgrade_info_7db780a713a4.txt and failed.txt. I think with a little more work, I’ll figure out if there is a recovery method using tftp without serial access. This would be necessary if you lose telnet access and need to rebuild the kernel partition that hosts telnetd.

Tools

DAHUA IP Camera Recovery v1.0.pdf………………….. http://tinyurl.com/lbl3up7

Port Scanner ………………………………………….. http://tinyurl.com/q53pojg

Putty …………………………………………………….. http://tinyurl.com/lvbbmsq

Tftp Server …………………………………………….. http://tinyurl.com/m46wnhe

Dahua Docs & Tools

DAHUA_HTTP_API 1.0 .pdf ………………………………………… http://tinyurl.com/lb43lga

DAHUA_HTTP_API_1.23.pdf ………………………………………… http://tinyurl.com/lrwye3k

DAHUA_HTTP_API_FOR_IPC 1.28.pdf …………………………………. http://tinyurl.com/kskrcay

DAHUA_HTTP_API_FOR_IPC&SD-V1.36.pdf ……………………………… http://tinyurl.com/mooccf9

DAHUA_HTTP_API_FOR_IPC&SD-V1.37.pdf ……………………………… http://tinyurl.com/kvyddfp

DAHUA_HTTP_API_FOR_DVR_V1.29.pdf ………………………………… http://tinyurl.com/klc72tr

General_ConfigTool_Eng_V1.0.5.R.120428.zip …………………… http://tinyurl.com/mwlzbb3

General_ConfigTool_Eng_V1.06.1.T.120807.zip …………………… http://tinyurl.com/leudphu

General_ConfigTool_Eng_V1.07.2.R.130304.zip ………………….. http://tinyurl.com/obs5ud7

General_ConfigTool_Eng_V1.07.3.R.130701.zip ………………….. http://tinyurl.com/o6p628f <—- Use this one

General_ConfigTool_Eng_V2.00.0.R.140410.zip …………………… http://tinyurl.com/nbqtgev

Firmware Files

Firmware files are grouped by camera type and video signal (NTSC –> Eng_N / PAL –> Eng_P / or BOTH –> Eng_NP)

Files are ordered by version number with the latest Firmware in blue.

Files with DH_ prefix are DAHUA direct firmware files and those with General_ prefix are general release for OEM cameras but I’ve had good luck with both.

DH_IPC-HX1100_Eng_NP_V2.210.0000.3.R.20140416.bin ………………………………………….. http://tinyurl.com/m2jf3qv

General_IPC-HX3(2)XXX_Eng_N_V2.210.0001.0.R.20130517.bin ……………………………………….. http://tinyurl.com/q98zg9x

General_IPC-HX3(2)XXX_Eng_P_V2.210.0001.0.R.20130517.bin ………………………………………… http://tinyurl.com/nekapn3

General_IPC-HX3(2)XXX_Eng_NP_V2.210.0001.0.R.20130517.bin ……………………………………… http://tinyurl.com/p59ym6z

General_IPC-HX3(2)XXX_Eng_P_V2.211.0000.0.R.20130726.bin ………………………………………… http://tinyurl.com/my54r9z

General_IPC-HX3(2)XXX_Eng_N_V2.212.0000.0.R.20131206.bin ……………………………………….. http://tinyurl.com/lrvtm2z

General_IPC-HX3(2)XXX_Eng_P_V2.212.0000.0.R.20131206.bin ………………………………………… http://tinyurl.com/n9rv23n

General_IPC-HX3(2)XXX_Eng_N_V2.212.0001.0.R.20131224.bin ……………………………………….. http://tinyurl.com/l5kg2d9

General_IPC-HX3(2)XXX_Eng_P_V2.212.0001.0.R.20131224.bin ………………………………………… http://tinyurl.com/q6c2gox

DH_IPC-HX3(2)XXX_Eng_NP_8M_V2.212.0000.4.R.20140307.bin ……………………………………….. http://tinyurl.com/mnzx33h

DH_IPC-HX3(2)XXX_Eng_NP_8M_V2.212.0000.5.R.20140326.bin ……………………………………….. http://tinyurl.com/ke285w5

DH_IPC-HX3(2)XXX_Eng_NP_8M_V2.212.0000.6.R.20140419.bin ……………………………………….. http://tinyurl.com/mllzcox

General_IPC-HX3(2)XXX_Eng_P_V2.420.0000.0.R.20140414.bin ………………………………………… http://tinyurl.com/nftaogy

DH_IPC-HX3(2)XXX_Eng_N_V2.420.0000.0.R.20140414.bin ……………………………………………. http://tinyurl.com/ma5q64d

General_IPC-HX5(4)XXX_Eng_P_V2.210.0000.2.R.20130821.bin …………………………………………. http://tinyurl.com/pdcdmdk

General_IPC-HX5(4)XXX_Eng_N_V2.210.0000.4.R.20130911.bin ……………………………………………….. http://tinyurl.com/pdoxjzj

General_IPC-HX5(4)XXX_Eng_P_V2.210.0000.9.R.20131217.bin ……………………………………………….. http://tinyurl.com/p3g4t54

General_IPC-HX5(4)XXX_Eng_N_V2.210.0000.10.R.20140111.bin ……………………………………………… http://tinyurl.com/mnjpd79

General_IPC-HX5(4)XXX_Eng_P_V2.210.0000.12.R.20140225.bin ……………………………………………… http://tinyurl.com/nssnph6

DH_IPC-HX5(4)XXX_Eng_NP_V2.210.0000.12.R.20140225.bin …………………………………………….. http://tinyurl.com/lcjr8xv

DH_IPC-HX5(4)XXX_Eng_NP_V2.210.0000.16.R.20140421.bin …………………………………………….. http://tinyurl.com/k67gu9u

DH_IPC-HX5(4)XXX_Eng_NP_V2.210.0000.18.R.20140429.bin ……………………………………………. http://tinyurl.com/n779scx

General_IPC-HX5(4)XXX_Eng_N_V2.210.0000.21.R.20140613.bin ……………………………………………… http://tinyurl.com/qd2thhe

General_IPC-HX5(4)XXX_Eng_P_V2.210.0000.21.R.20140613.bin ……………………………………………… http://tinyurl.com/p8q75b4

General_IPC-HX5(4)XXX_Eng_N_V2.400.0000.0.R.20131231.bin ……………………………………………….. http://tinyurl.com/kmd7hu9

DH_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0000.0.R.20140419.bin ………………………………………….. http://tinyurl.com/mb75g2n

DH_IPC-HX5(4)XXX_Eng_P_Stream3_V2.420.0002.0.R.20140621.bin …………………………………….. http://tinyurl.com/laj29k5

General_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0000.0.R.20140419.bin ………………………………….. http://tinyurl.com/mzw85fz

General_IPC-HX5(4)XXX_Eng_P_Stream3_V2.420.0000.0.R.20140419.bin ………………………………….. http://tinyurl.com/ov6krph

General_IPC-HX5(4)XXX_Eng_P_Stream3_P2P_V2.420.0000.0.R.20140419.bin …………………………… http://tinyurl.com/oxgblkq

General_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0002.0.R.20140621.bin ………………………………….. http://tinyurl.com/kejg3fv

General_IPC-HX5(4)XXX_Eng_P_Stream3_V2.420.0002.0.R.20140621.bin ………………………………….. http://tinyurl.com/pfmevdu

General_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0003.0.R.20140930.bin ……………………………………….. http://tinyurl.com/kchslos

General_IPC-HX5(4)XXX_Eng_N_V2.420.0003.0.R.20140930.bin ……………………………………………….. http://tinyurl.com/ok4f8fx

General_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0005.0.R.20141205.bin ………………………………………. http://tinyurl.com/qbrfg3k

General_IPC-HX5(4)XXX_Eng_P_Stream3_V2.420.0005.0.R.20141205.bin ………………………………….. http://tinyurl.com/ot99vgw

DH_IPC-HX8XXX_Eng_NP_V2.400.0000.2.R.20140506.bin …………………………………………………. http://tinyurl.com/lbar98x

I will also post the bare metal img files when I get some time which contain the firmware and all the img files including the update.img that can be used for serial recovery.

I have just started the process of uploading firmware… There are much more to come as well as many more camera models.

Also if you have any you want to share please PM me what you have and where I can link them to this thread.

Thanks to Euly for sharing firmware files!

IMPORTANT NOTE FOR IPC-HFW4300S-V2 CAMERAS

The new camera appears to have differences (a few that I already found) that makes some of the general firmware incompatible with them. I have found a workaround, but it is complex. I will try to summarize it in a separate thread in the following weeks. I will also repackage the newest firmware files in versions that will work for the V2 cameras. Stay tuned! In the meantime, you can use General_IPC-HX5(4)XXX_Eng_N_V2.210.0000.21.R.20140613.bin or the PAL equivalent to recover your camera.

Well, that’s all I have time to share for now, but I’ll do my best to put together a comprehensive guide to the inner workings of these cameras and a guide to unbrick in any failed software situation.

Thanks and take care.

<p>The post Unbricking your Dahua IP camera (Tips, Tricks & Firmware) first appeared on NVR IPCAMERA SECURITY.</p>

Tapo was created to engage in the small intelligent appliances market, to help people adopt a new smart home lifestyle at an affordable cost. That’s why we insist on Smart, Easy, Secure.

.

What should I do if I fail to configure the Tapo Smart Plug?

The Tapo app will guide you step by step during the initial configuration, but you may not be able to get through all the steps due to some interference. This FAQ will tell you what to do if you have trouble getting through a certain step.

Case 1

The phone is looking for the smart device via Bluetooth or its default 2.4GHz WiFi, if you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

Tapo Smart Camera FAQ v1

Case 2

If you are unable to find your home Wi-Fi network, please refer to the following suggestions.

Troubleshooting tips:

1. The signal strength of your home Wi-Fi network is a bit weak, move the smart device closer to your router for a try.

2. Ensure your home Wi-Fi network is a 2.4GHz Wi-Fi network, the Tapo device does not support a 5GHz Wi-Fi connection.

3. If it doesn’t display the Wi-Fi name of the router automatically, please click on “RECAN” at the upper right corner to refresh the Wi-Fi list.

4. If the router’s SSID is hidden, please choose “Other” to input SSID and password manually.

5. Please change the wireless channel of the 2.4G Wi-Fi network to 1, 6 or 11.

6. Reset the device as per QIG/UG and go through the process again.

Case 3

If you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

1. Ensure you have selected the correct home Wi-Fi network and have entered the correct wireless password. If the Wi-Fi network or password is incorrect, click on “Choose a Network” and select the Wi-Fi network again.

2. Make sure your smart device is within the Wi-Fi range of your router.

3. Turn your phone’s or tablet’s Bluetooth off and back on.

4. If the problem persists, try to reset the smart device as per UG/QIG, and then set it up again.

5. Check if there is a firewall on your router. If yes, please turn it off.

6. Change the wireless security type of the 2.4G network to WPA2.

7. Try to connect the Tapo plug to the hotspot of your cell phone or another wifi network. If it works, please upgrade the firmware for the plug, then reset and reconnect it to your router.

.

What features does Tapo smart plug and Tapo smart switch support?

Currently the Tapo plug and switch supports the following features:

.

How to view Tapo camera on PC/NAS/NVR through RTSP/Onvif Protocol

The Tapo camera supports the RTSP and Onvif protocol, so it can work with third-party NVR or NAS devices that also support the RTSP/Onvif protocol. If a user wants to view the live stream of the camera with a third-party app like VLC Player, iSpy, here is the method for him.

Notes:

1. The username/password is the camera account that you created via the Tapo app. If you haven’t created the username and password, please follow the instruction of Step 1 in this article.

2. The IP address is the camera’s IP address assigned by your host router. You can find it on your host router’s DHCP list or in the Tapo app (Go to the Device Settings page of the camera and tap Device Info to see its IP).

3. If you want to view the live stream of the Tapo camera with a third-party app remotely, you will need to open port 554 for the camera on your host router first. Please enable the TCP forwarding for port 554.

4. You could use ONVIF standards to add the Tapo camera with its username/password and IP address. Please see the example of iSpy in Case 2 to know how to use onvif protocal to control the camera.

5. For Tapo C310, the resolution of the stream1 is determined by the video quality set on the Tapo APP.

If you need to watch the 3MP HD Video via RTSP, please change the video quality to Best Quality on the Tapo APP and use: rtsp://IP Address/stream1

6. If the Camera is inserted microSD card and subscribed Tapo Care, its RTSP stream will fail. You need to remove microSD card or cancel Tapo Care to get its RTSP stream.

7. If you find that there’s no or very little sound when using RTSP/Onvif to watch live stream, please adjust the camera microphone on Tapo APP.

Apart from the Tapo app, Tapo cameras can work with other third-party software to use and manage your Tapo camera.

Note: Before you start, make sure the computer/NAS/NVR and your camera are connecting to the same network or can visit the public IP and port of your camera.

Step 1: Create a camera account in the Tapo app

1. On the Home page, tap on your camera model card to go to the camera Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Advanced Settings, then select Camera Account to create an account (username and password) for camera login on other portals.

You will see a prompt like below (About Camera Account), please read it and tap Understand and Agree to Use, then you can create an account for the camera.

Note: The username and password should contain 6 to 32 characters.

Step 2: Add your Tapo camera on iSpy (Example of Onvif protocol connection)

1. Run the iSpy software on your computer.

2. Click Add on the top left menu and select ONVIF Camera.

3. Enter the Username and Password that you set for your camera on the pop-up window, select Network Address, and click Next. You can customize other parameters if needed.

4. Choose the video resolution and click OK.

5. Customize the camera settings as needed, including Microphone, Talk, Motion Detection, Alerts, Recording, Images, Scheduling, and Storage. You can also change all the settings later. Click Finish to complete adding your camera to iSpy.

6. After adding your Tapo camera to iSpy, you can monitor and manage it using the app. View the live, customize motion detection, check the recordings when motion detected, set recording schedules, record videos and more.

Step 3: Watch your Tapo camera on VLC (Example of RTSP protocol connection)

1.Open the VLC software, select Media > Open Network Stream

2.Fill in the URL of the Tapo camera

The URL of the RTSP live stream for the Tapo cameras will be:

For high quality stream1: rtsp://IP Address/stream1

For low quality stream2: rtsp:// IP Address/stream2

In some software, the URL need to add the port to access live stream, the default port is 554:

For high quality stream1: rtsp://IP Address:554/stream1

For low quality stream2: rtsp:// IP Address:554/stream2

If you fail to stream the Tapo camera via the RTSP/ONVIF protocol, you may refer to the article for the troubleshooting:

https://community.tp-link.com/en/smart-home/forum/topic/652710

To get to know more details of each function and configuration, please go to Download Center to download the manual of your product.

.

How to factory reset the Tapo or Kasa smart plug

.

To restore a Tapo or Kasa smart plug to its factory default settings and re-enable the setup mode, please press and hold the power button for 10 seconds.

The LED status for a factory reset varies by model:

After a completing the reset, you can then connect and configure the device in the Tapo App.

How to avoid noise when monitoring the sound from Tapo camera

Tapo cameras are capable of not only monitoring video stream from the camera, but also monitoring sound collected by the built-in microphone on the cameras. You can turn on/off the sound feature like the monitor screen as below. But to increase or decrease the volume, you need to press the volume button on your phone.

Why is there noise?

Noise is a physical phenomenon and it’s actually inevitable. Basically, the IP cameras including other brands’ have background noise more or less. And those cameras which seem to generate less noise probably have worse sound collecting performance. Tapo cameras are designed with a sensible sound collector which might take some noise in your monitor. Even though it is inevitable at present, we are still trying our best to make improvement and searching for better solutions.

How to reduce the noise?

1.     Please keep your mobile device away from the camera as much as possible. The Tapo camera is designed for remote access and monitoring via cloud service, local usage in close range may cause interference and noise between your mobile device and the camera.

2.    Please reduce the output volume below 50% since a louder volume may enlarge noise decibel. The value between 40%-50% is suggested with not only good sound quality but also minimum noise decibel. As long keep focus on our cloud camera you will find our progress on new models.

Your understanding is highly appreciated!

How to edit Home and Away Mode for Tapo&Kasa Cameras on the Tapo app

.

The Away mode and the Home mode are two different sets of Detection, Alarm, and Notification settings for Tapo&Kasa cameras. You can tap the button on the Tapo app>Cameras tab to quickly apply the preset settings to the cameras when you are home or away.

Note:

Here we take the Home Mode as an example.

For Tapo Cameras:

1. Open Tapo APP, find the Cameras tab at the bottom, and locate the Detection Mode section.

You can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three-dots option.

2. Click on Add Devices if you want to add more cameras to the Home mode.

Click on the Edit icon at the top right corner if you want to delete cameras from the Home mode.

3. Select the camera you want to edit the mode settings. Here we take Tapo C200 as an example, and you can change the Privacy mode, Detection, Alarm, and Notification settings of the camera.

Take the Motion Detection feature as an example. You can click on Motion Detection to turn it on or off, change the Motion Sensitivity, and set the Activity Zones on the Motion Detection page.

And you can also click on Detection>Person Detection or Baby Crying Detection to turn them on or off, and tap Alarm and Notifications to configure the related settings.

4. Click on the Back icon at the top left corner of the Tapo C200 page if you have changed the configurations, and click on other cameras if you want to change their configurations.

After completely presetting the Home or Away Mode, you can tap the Home mode or Away mode card on the Tapo app>Cameras tab to switch your cameras’ settings quickly.

For Kasa Cameras:

Here we take KC115 as an example.

1. Open the Tapo app, find the Cameras tab at the bottom and you can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three dots option.

2. Select the camera you want to edit the mode settings and enter the Detection & Alerts page.

3. You can change the Privacy mode, Detection, and Notification settings of the camera.

Tap Detection > Motion Detection to edit the motion detection function. You can adjust Motion Sensitivity.

Tap Detection>AI Detection to change your AI Detection feature, such as Person Detection.

4. After editing the detection settings, tap Detection & Alerts > Notifications to customize its current settings.

After completely presetting the Home or Away Mode, you can tap the card on the Tapo app>Cameras tab to switch all of your cameras’ detection settings to the mode you want.

.

How can I find the IP address of my Tapo&Kasa camera

Note: Some Tapo battery cameras or doorbells need to work with the hub and can’t connect to the router directly, which do not have IP address.

There are two methods to find the IP address of the camera.

Here we take Tapo C200 as an example.

Method 1: Via Tapo app

1. On the Tapo app> Home page, tap your camera model card to go to the Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Device Info and then you can find the IP address of your camera.

Method 2: Via the web management page of your router

Here we take the TP-Link router Archer C7 as an example.

1. Log in to the management page of your router.

2. Go to Advanced > Network > DHCP Server and locate the DHCP Client List section to find the IP address of your camera.

How can I view continuous recordings of Tapo&Kasa cameras on the Tapo app?

This article will show you how to view continuous recordings on the Tapo app.

Note:

For Tapo Cameras

Here we take Tapo C200 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

Click on Recording Schedule to see the detailed recording schedule settings.

Tap Edit on the Recording Schedule page if you want to change the Continuous Recording and Detection Recording schedule.

And please tap the tick icon at the top right corner to save your changes.

Step 3.

On the camera’s Live View page, tap Playback & Download, select the SD Card icon on the Playback page, select the date, and then you can drag the timeline to view the continuous recordings.

For Kasa Cameras

Here we take KC115 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

On the Live View page of the camera, tap Playback & Download > Playback to view all recordings. Drag the timeline and you can view recordings whenever you want and wherever you are.

What can I do if the video image is upside down on my Tapo&Kasa camera

Tapo&Kasa cameras support the function of Video Rotation, and if the camera video image is upside down on the Tapo app, please refer to the following steps to correct it.

Here we take Tapo C200 as an example.

1. On the Home page of the Tapo app, tap your camera model card or tap the Cameras tab>click on Manage on your camera model to go to the Live View page.

2. On the Live View page, tap the icon on the top right corner to enter the Device Settings page.

.

What can I do if I can’t find my Tapo camera on Tapo APP?

If your device does not appear on your app after completing the configuration process, please try the following troubleshooting suggestions:

1. If you are using a Wi-Fi wireless configuration to connect your camera, please check if the camera has successfully connected to the router. You can verify whether the camera is connected to Wi-Fi by checking the System light of your camera. For most Tapo Cams, if it is not connected properly, the LED light will blink red slowly. For the HomeKit version Camera, its LED light indicator will blink blue slowly. If the camera cannot connect properly, we recommend resetting the camera to factory default settings as per the User Guide and then reconfiguring the camera.

How to reset my Tapo camera

2. Check the DHCP settings on your router and ensure that the DHCP Server of your router is enabled. If the camera has already connected to the router properly, you will see the device in the client list of your router. If you don’t know how to do this, please contact your router’s customer support.

3. Please verify if there are any special symbols in your Tapo account（TP-Link ID） password. If there are, try to remove them and make the account password simpler by only using numbers and English letters. Then reset and add the camera from the beginning again.

4. Connect your smartphone to the same Wi-Fi network as your camera and check whether you can see it on the Tapo app. If you can see it, that means the camera fails to connect to the cloud for unknown reasons and you cannot access it remotely. In this case, verify if any firewall or security settings are blocking the connection to the Cloud Server. Temporarily disable any antivirus, firewall, or security software to see if it resolves the issue

.

5. Using a public DNS server may improve the connection, try changing your router’s DNS server settings to 8.8.8.8. If you don’t know how to do this, please contact your router’s customer support.

To eliminate potential issues with the router’s Wi-Fi network, it is recommended to use a mobile hotspot and configure the Camera to test its functionality.

Here are steps for using a mobile hotspot to test the Camera’s configuration:

Preparation: We suggest having two phones. Use one phone (Phone A) to create a hotspot and use another phone (Phone B) to download the Tapo app and complete the setup process.

Steps:

1. On Phone A, disable Wi-Fi and enable only mobile data.

2. On Phone A, navigate to phone settings and access the “Personal Hotspot” or “Mobile Hotspot” option, ensuring that the “Mobile Hotspot” feature is activated. Please make sure the created hotspot operates on a 2.4GHz network.

3. Set a unique name and password for the hotspot, different from your router’s Wi-Fi, to facilitate the Camera’s connection.

4. On Phone B, download the Tapo app. Follow the app’s instructions to add the device and complete the remaining setup steps as guided by the app.

Please contact TP-Link technical support with the following information if the issue persists after the above suggestions.

1) Your TP-Link ID or cloud account.

2) The model number of your TP-Link Cam and its MAC address.

3) The model number of the host router.

4) Whether you have tried all the suggestions listed above or not. If yes, what are the results?

<p>The post Tapo Smart Camera FAQ v1 first appeared on NVR IPCAMERA SECURITY.</p>

How to Change the Password on a 5.0 UI IP Camera

.

IPCamera/Change Password 5.0 UI

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the current username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the System option from the drop-down list

3. Select Account on the left.
Then select the User tab at the top.
Click on the Edit (Pencil) icon to the right of the user account who’s password you want to edit

4. Enable the Change Password slider.
Then enter the current password in the Old Password field.
Enter the new password you want to change it to in both the New Password and Confirm Password fields.
Click on OK at the bottom

5. Once the new password is successfully changed, you will see “Modify User Succeeded” at the top

Dahua IP Camera 5.0 UI Setup

How to Set the Date and Time on a 5.0 UI IP Camera

.

IPCamera/Set Date and Time 5.0 UI

Description

This guide will show you how to set the Date and Time on a IMaxCamPro IP Camera with the 5.0 User Interface

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the System option from the drop-down list

3. Select General on the left.
Then select the Date & Time tab at the top.
To set the date and time without an NTP server, select Manual Setting. Then adjust the Time, Time Format, and Time Zone. (You can press Sync PC if you want to pull the time from the PC you are using. The Time Zone still needs to be set manually though.)

To set the date and time with an NTP server, select NTP. Then fill in the information for a functioning NTP server. (This will only work if the camera has access to the internet.)
For locations that use Daylight Saving Time, enable the slider below DST and select the dates and times that Daylight Savings starts and stops.
When you are done adjusting settings, select Apply at the bottom to save the settings.

How to Set the IP to Static on a 5.0 UI IP Camera

.

IPCamera/Set IP to Static 5.0 UI

How to Set IP Settings to Static on a 5.0 UI IP Camera

Description

This guide will show you how to set the IP settings to static on a ImaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the Network option from the drop-down list

3. Select TCP/IP on the left.
Click on Static next to “Mode”.
Then fill in the IP Address, Subnet Mask, Default Gateway, and DNS settings below that. (You can press the “Test” button if you want to see if that IP address is free on your network.)
When you are done adjusting settings, click on Apply at the bottom

How to Configure Recording to an SD Card on a 5.0 UI IP Camera

.

IPCamera/Configure Recording SD Card 5.0. UI

How to Configure Recording to an SD Card on a 5.0 UI IP Camera

Description

This guide will show you how to configure recording to an SD Card on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the Storage option from the drop-down list

3. Select the SD card from the list by enabling the radio button on the left.
Click on Format at the top to wipe all the data on the SD card and configure it for recording on this camera.

4. Click on the Home icon at the top left.
Select Record. (If you don’t see it on the main page, click the right circle at the bottom to switch pages.)

5. Select the Record Control tab at the top.
Adjust the settings on this page as desired:

When you are done adjusting settings, click on Apply to save the settings

6. Select the Time Plan tab at the top.
Adjust each Event Type on the weekly calendar.
When you are done adjusing the schedules, click on Apply to save your changes

7. Select the Storage tab at the top.
Adjust the settings on this page as desired:

When you are done adjusting settings, click on Apply to save the settings

How to Playback Video from an SD Card on a 5.0 UI IP Camera

.

IPCamera/Playback Recording SD Card 5.0. UI

How to Playback Video from an SD Card on a 5.0 UI IP Camera

Description

This guide will show you how to view recorded video footage from an SD Card on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Click on the Home icon at the top left.
Select Record. (If you don’t see it on the main page, click the right circle at the bottom to switch pages.)

3. Select the Search Video tab at the top.
Select the start date and time, and the end date and time on the left.
Then click Search below that.
All the recorded footage on the SD card in the time range will appear.
Double-click on the specific clip you want to play

4. Move the slider at the bottom to adjust the playback time.
Use the controls to play, pause, rewind, fast forward, or jump between clips

IPCamera/Password Reset 5.0. UI

.

IPCamera/Password Reset 5.0. UI

How to Reset the Password on a 5.0 UI IP Camera

Description

This guide will show you how to reset the password on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

Reset via Password Recovery in DMSS

1. Input the camera’s IP address into a web browser.
Click on Forgot password?

2. Click on OK to agree to use your email address in this process

3. If you setup a recovery email you will be brought to a page with a QR code on it. (If you didn’t setup a recovery email, skip to “Reset via Physical Button” at the bottom of this page.)

4. Open the DMSS app on a mobile device.
Tap on Me at the bottom.
Then select Tool Manager

5. Tap on Device Password Management

6. Use the mobile device’s camera to scan the QR code from Step 3 above

7. Once the QR Code has been successfully scanned you will see the following message

8. Check the email inbox for the email address that was registered for password recovery on this device.
Input the security code from that email in the Security code field.
Then click on Next

9. Enter a new password in the New Password and Confirm Password fields.
Then click on OK

10. The password will be successfully reset

Reset via Physical Button

Depending on the model of your IP Camera, there could be a physical reset button on the outside body of the camera, or inside the camera body.

1. Reset: Press the reset button for 10-20 seconds while the camera is connected to power.

IP Camera Basic Info

Important Safeguards and Warnings

1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The product must be grounded to reduce the risk of electric shock. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.

2．Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.

3．Installation

4．Qualified engineers needed All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment The NVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. This series product shall be transported, storage and used in the specified environments.

6. Accessories Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package.

7. Lithium battery Improper battery use may result in fire, explosion, or personal injury! When replace the battery, please make sure you are using the same model! Before your operation please read the following instructions carefully.

Hardware Installation and Connection

Note: All the installation and operations here should conform to your local electric safety rules.

1. Check Unpacked NVR When you receive the NVR from the forwarding agent, please check whether there is any visible damage. The protective materials used for the package of the NVR can protect most accidental clashes during transportation. Then you can open the box to check the accessories. Please check the items in accordance with the list (Remote control is optional). Finally you can remove the protective film of the NVR.

2. About Front Panel and Rear Panel For detailed information of the function keys in the front panel and the ports in the rear panel, please refer to the User’s Manual included in the resource CD. The model label in the front panel is very important; please check according to your purchase order. The label in the rear panel is very important too. Usually we need you to represent the serial number when we provide the service after sales.

3. After Remove the Chassis Please check the data cable, power cable, COM cable and main boar cable connection is secure or not.

4. Important：Please turn off the power before you replace the HDD. You can refer to the User’s Manual for recommended HDD brand. Please use HDD of 7200rpm or higher. Usually we do not recommend a PC HDD. For detailed operation instruction, please refer to the User’s Manual included in the resources CD.

1. Use the screwdriver to loose the screws of the rear panel and then remove the front cover.

2. Put the HDD to the HDD bracket in the chassis and then line up the four screws to the four holes in the HDD. Use the screwdriver to fix the screws firmly to secure HDD on the HDD bracket

3. Connect to the HDD data cable to the main board and the HDD port respectively. Loosen the power cable of the chassis and connect another end of the power cable to the HDD port.

4. After connect the cable, put the front cover back to the device and then fix screws of the rear panel.

<p>The post Dahua IP Camera 5.0 UI Setup first appeared on NVR IPCAMERA SECURITY.</p>

By downloading the firmware from this web page you are agreeing to Hikvision’s Software User License Agreement. Please be aware that Hikvision products are region-specific and regionally supported. If you have purchased your Hikvision products from an online source or unauthorized distributor, they may not be compatible with the North American region’s firmware and are considered to be “gray market” product. If your camera has “CH” in the serial number, you are most likely using a “gray market” product. 

Updating the firmware from this site can lead to several complications in those cameras, up to and including camera failure.  Restoring a “gray market” product to its original condition is a factory process and will result in a Chinese interface. As Hikvision warranty is void in this case, you must rely on the dealer for any service, support, and warranty of the “gray market” product. If you have any questions or concerns about the official status of your Hikvision distributor, please contact Hikvision USA Customer Service at cust.usa@hikvision.com.

.

Upgrade Device Firmware

For a device added via IP/Domain, its new version can be detected by the Mobile Client. Once detected, you can upgrade the device to its latest version.

1.Enter the Device Information page.

• On the device list page, if the page is in the list mode, swipe the device name to the left and tap .

• On the device list page, If the page is in thumbnail mode, tap the device name or tap .

• On the Live View page. Tap  and then tap Settings.

Note:

For details about how to enter the Live View page, see Start and Stop Live View.

2.Tap  > Device Version to enter the Device Version page.

3.Tap Upgrade and then tap UPGRADE on the pop-up window.

The Mobile Client will download the upgrade file first and then start upgrading the device.

Note:

You can also enable the Mobile Client to automatically download the upgrade file in Wi-Fi networks once a new device version is detected. For details, see Auto-Download Upgrade File.

.

UPDATING FIRMWARE

Hikvision regularly updates the firmware in our products to resolve potential issues and keep your system running smoothly. Below, you can find guidance on how to update your system accordingly.

Updating Hikvision IP Camera Firmware

To upgrade the firmware of a Hikvision IP camera, please follow the steps below:

1.Locate the appropriate firmware by clicking this link

2.Click on the firmware, then click download.

3.Agree to the license terms and conditions when prompted.

4.Locate the downloaded firmware file (this typically will be in the default download folder, unless prompted for a download location, then choose Desktop) and extract it by right-clicking on the file and selecting extract all or unzip. When prompted for an extract location, choose Desktop to extract the final file to. A file labeled DIGICAP will appear on the desktop.

5.After the file is extracted, log into the camera using Internet Explorer or Firefox web browsers. If prompted to install the plugin (or to allow the plugin to run), follow the prompt to proceed with the upgrade procedure.

6.Log into the camera using the administrator username and password, then go to the Configuration tab. In this tab, go to Basic Configuration then System, and then click on the Maintenance tab.

7.On the bottom of the page under Remote Upgrade, press the Browse button to locate and choose the firmware file, which was previously saved on the Desktop. After selecting the file, click Open, then click Upgrade.

8.The camera will display a prompt that a reboot is necessary to complete the upgrade. Click OK. The camera will reboot when the firmware is successfully upgraded.

Click here to see a video tutorial of the above steps.

Upgrading Hikvision DVR/NVR Firmware

To upgrade the firmware of a Hikvision DVR or NVR, please follow the steps below:

1.Insert a USB flash drive into the computer’s USB port (Please note that the USB flash drive does not need to be empty; it may contain other files and documents).

2.Locate the appropriate firmware by clicking this link

3.Click on the firmware, then click download.

4.Agree to the license terms and conditions when prompted.

5.Locate the downloaded firmware file (this typically will be in the default download folder, unless prompted for a download location, then choose Desktop) and extract it by right-clicking on the file and selecting extract all or unzip. When prompted for an extract location, choose the USB flash drive (typically labeled by letters E, F and so on) to extract the final file to. A file labeled DIGICAP will appear in the USB flash drive.

6.After the firmware has been extracted (unzipped), remove the USB flash drive from the computer and insert it into one of the available USB ports on the DVR/NVR unit.

7.On the DVR/NVR, go to the Main Menu, and then go to Maintenance.

8.From the sub-menus on the left click Upgrade. This will display the content of the USB flash drive.

9.Choose the DIGICAP file and press Upgrade.

10.An information window will pop up prompting that the unit will reboot after the upgrade is complete. Click YES.

11.To verify that the firmware has been upgraded, after the DVR/NVR is rebooted, go to the Main Menu, and then go to System Information. The current firmware version will be displayed.  

New Hikvision Firmwares 2024

Also Read : Hikvision How To Tutorials Chapter 1

How do I get Firmware Updates for my Hikvision Gear?

Hikvision Australia’s website has firmware updates for available IP cameras.
https://www.hikvision.com/au-en/

Use the search bar to try and find your product. Firmware updates are usually available on the product page.

IF YOU BOUGHT EQUIPMENT FROM US:

You will need to contact us if you can’t find your camera listed or if you require firmware for your NVR / DVR.
You will need to also provide the full serial number of the device as well as your current firmware.
This is to ensure upgrades are done properly. In some instances middlle firmware is required before upgrading to the latest version.

We do not recommend doing intercom firmware upgrades. Please check with us if there is any doubt.

If you didn’t buy equipment from us, please contact the people who you bought the equipment from.

How to Upgrade Camera Firmware via Hikvision NVR

This Video shows you how to upgrade your Camera firmware from the NVR.

Hikvision Australia’s website has firmware updates for available IP cameras.
https://www.hikvision.com/au-en/Support/Downloads/Firmware/IPC

NOTE this is only for IPC.

You will need to contact us if you can’t find your camera listed or if you require firmware for your NVR / DVR.
You will need to also provide the full serial number of the device as well as your current firmware.
This is to ensure upgrades are done properly. In some instances middlle firmware is required before upgrading to the latest version.

We do not recommend doing intercom firmware upgrades. Please check with us if there is any doubt.

 .

Lates Hikvision Firmwares 2024

How do I update Hikvision firmware remotely for my TetherX installation?

If your system was installed by one of our security installation partners please contact them to update your cameras. If you would like to update your Hikvision devices yourself please follow the guide below.
​

.

1.Download the latest Hikvision firmware by visiting the Hikvision Downloads Page

Hikvision Downloads Page

Note: the UK firmware is different from the US firmware. For UK firmware, please follow use the UK Downloads page.
​
​

2.Extract the firmware archive, it should contain the file: digicap.dav

3.Create a tunnel into your Hikvision device.

How to create a tunnel?

​

4.Login to your Hikvision device and navigate to “Configuration” then “Maintenance”.

​

5.At the bottom of the page under the ‘Upgrade’ header, press on “Browse”

​

6.Use the file navigator window that pops up to select the digicap.dav file you downloaded earlier
​

7.Click on ‘Upgrade’

.

The actual upgrade will take up to 10 minutes and the device will automatically reboot at the end of the upgrade process.
​
This video from Hikvision Technical Support shows the upgrade process:

.

Click here to see a video tutorial of the above steps.

00 Temperature Screening-2020-07-10

01 Density Control-2020-07-10

02 Mask Detection-2020-07-17

03 Front Ends-2020-12-02 

04 Back Ends-2023-03-15

Access Control & Video Intercom-2020-12-02

Accessaries-2021-12-01

Alarm-2023-06-21 

ANPR & Speed Radar Display-2023-07-10

Dell image-2022-12-12

Mobile-2023-07-03 

Paxton related materials-2023-05-26

Portable Series-2024-02-06 

Thermal-2023-07-07 

Transmission & Display-2022-12-16

.

DVR-2023-08-11 

IPC-2021-11-04 

NVR-2021-11-26 

PTZ-2021-09-23 

fw and model list.xlsx10.27KB2019-04-09

.

.

.

.

.

Hikvision Firmware Download –
Intelligent Traffic Products

.

Hikvision Firmware Download –
Access Control Products

.

.

.

.

.

.

<p>The post New Hikvision Firmwares 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Lorex Fusion: Download the Lorex App

The following article provides instructions for downloading the Lorex App and connecting your Lorex Fusion Collection recorder to the app.

Prerequisite

Before you start, your Fusion recorder must be powered on and connected to your router using the included Ethernet cable. For Basic System Setup instructions, refer to your Fusion recorder’s Quick Start Guide or Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

Download the Lorex App

Once your Fusion recorder has connected to the Lorex App, complete the final Fusion steps by connecting your Fusion Wi-Fi cameras and accessories.

For setup instructions using the new local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (New Local UI).

For setup instructions using the previous local UI, please see the article Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories.

Lorex Fusion: Frequently Asked Questions

The following frequently asked questions (FAQs) provide more information about your Lorex Fusion Collection. Where applicable, the FAQ includes links to articles where you may find more information.

Lorex Fusion Troubleshooting FAQ.

What is Lorex Fusion?

Our Lorex Fusion recorders incorporate the newest (fusion) technology to connect both Lorex Wired and Fusion Wi-Fi Cameras, Doorbells, Floodlights, and Sensors to one system. Lorex Fusion Wi-Fi Cameras and Accessories can connect to one recorder for continuous 24/7 recording and local, secure storage (up to 10TB). Everything can be accessed from your Lorex App for easy control of all devices.

.

Why do I get an offline message and a blank screen for the (B463AJ) 2K battery doorbell’s channel on the Fusion recorder?

Being a battery-operated doorbell, it will always go to sleep after a period of inactivity to conserve battery life. Once the doorbell is correctly paired to your Fusion recorder, the offline message means the doorbell has gone to sleep but is still connected and can be awakened. When motion is detected, or when the call button is pressed, there will be live video from that channel. You can also manually wake up the doorbell through the Lorex app, by activating the liveview.

.

Can my Battery Video Doorbell record continuously?

To conserve battery life, Wi-Fi Battery Video Doorbells only record when motion is detected. They do not record continuously.

.

Which recorders are part of Fusion?

For a list of Lorex Fusion Recorders, please refer to the Product Compatibility Chart.

.

Can I connect all Lorex Wi-Fi Cameras and Accessories to my Fusion recorder?

Only Lorex Fusion Compatible Wi-Fi Cameras and Accessories can connect to Lorex Fusion Recorders.

.

Which Lorex Wi-Fi Cameras and Accessories are part of Fusion?

See the following list of Lorex Fusion Wi-Fi devices:

.

Should I update my Lorex Fusion recorder’s firmware?

It is recommended to update your system firmware to the latest version to ensure remote connectivity and to support newly added Fusion Wi-Fi devices.

.

Does my Lorex Fusion recorder require a network setup?

Yes, a network setup is required to connect Fusion Wi-Fi cameras and accessories to your Fusion recorder. Ensure you connect the included Ethernet cable to your recorder’s LAN port and your router.

.

Does it matter which router I use?

Yes, due to its strong signal, the dual-band router is suitable for high resolution video recording and for connectivity between devices. Ensure that your Fusion Wi-Fi cameras and accessories and your Fusion recorder are all connected to a dual-band router (2.4 GHz/5 GHz bands).

.

How many Lorex Fusion Wi-Fi Cameras and Accessories can I connect to my Fusion recorder?

This depends on your Fusion recorder and the number of Fusion Wi-Fi channels it comes with. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

What is a Fusion Wi-Fi channel?

A Fusion Wi-Fi channel is the channel you use to add a single Fusion Wi-Fi camera to your system. A 16-channel security system with 8 PoE ports/channels (for wired camera connection) and 8 Fusion Wi-Fi channels means that 8 Fusion Wi-Fi cameras and accessories can connect to the entire system.

Note: Fusion Wi-Fi channel’s are only available on certain Lorex Fusion recorders. For a list of Fusion recorders, see the Product Compatibility Chart.

.

How many Fusion Wi-Fi channels are on my Lorex Fusion Recorder?

The number of Fusion Wi-Fi channels varies per Fusion recorder. For full technical specifications, refer to the Product Specifications on your recorder’s product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

How do I setup my Lorex Fusion system?

Complete your Fusion setup in the following order:

After connecting your Fusion system, ensure you adjust your Fusion settings.

.

Are there Fusion setup tutorial videos?

For a video walk-through of the Fusion setup with the new local UI (N845, N846, N847, N864, D863, D881 Series), please watch here.

For a video walk-through of the Fusion setup with the previous local UI (N841, N842, N843, N844, N861, D862, D871 Series), please watch here.

.

How do I setup my Lorex Fusion recorder and wired cameras?

For Basic System Setup instructions, refer to your recorder’s Quick Start Guide or Series Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

.

How do I connect my Lorex Fusion Wi-Fi camera or accessory to my Fusion recorder?

For full setup instructions, please click on the article corresponding with your model number.

.

Which password should I enter to connect my Lorex Fusion Wi-Fi camera or accessory to my Fusion recorder?

Enter the same password that you created in the Lorex App when setting up your Fusion Wi-Fi device.

.

What is continuous recording?

Once your Lorex Fusion Wi-Fi camera connects to your Fusion recorder, your camera’s recording settings are automatically set to continuous. This means that your Fusion Wi-Fi camera will record 24/7 or for the entire duration of the recording schedule onto your Fusion recorder’s hard drive. It is worth noting that recordings on the camera are limited due to the size of its onboard storage, while recordings on the recorder are extensive (3TB to 10TB). Continuous recording captures everything in the background, and you can playback to catch anything you missed.

.

Do all Lorex Fusion Wi-Fi cameras record continuously?

No, to conserve battery life, battery-operated video doorbells do not record continuously (24/7).

.

How do I set my Lorex Fusion Wi-Fi camera to continuous recording?

After Fusion setup, your Wi-Fi camera is automatically set to Continuous recording. To adjust your camera’s recording settings, login to your recorder and navigate to the devices menu. For instructions, please see the article Lorex Fusion: Adjust Settings.

Note: Battery-operated video doorbells do not record continuously (24/7). Being a battery-operated doorbell, it will always go to sleep after a period of inactivity to conserve battery life. Once the doorbell is correctly paired to your Fusion recorder, the offline message means the doorbell has gone to sleep but is still connected and can be awakened. When motion is detected, or when the call button is pressed, there will be live video from that channel. You can also manually wake up the doorbell through the Lorex app, by activating the liveview.

.

How come I’m receiving duplicate notifications in the Lorex App?

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder. For instructions, please see the article Lorex Fusion: Adjust Settings.

.

After Fusion setup, where is my Lorex Fusion Wi-Fi camera’s video footage being stored?

Your Lorex Fusion Wi-Fi camera saves recorded motion detection videos onto the local microSD card (not always included). Once you’ve connected your Fusion Wi-Fi camera to your Fusion recorder, your camera’s recording settings is automatically set to 24/7 Continuous recording, and all recorded video is stored on your recorder’s extensive hard drive (up to 10TB).

.

What features are supported in my Fusion recorder vs. the Lorex App?

Please see the following list of features supported in either your Fusion recorder and/or the Lorex App:

.

Can I use my web browser to access my Lorex Fusion Wi-Fi camera?

You can only access your camera on the Lorex App, recorder, or on the Lorex Cloud Client.

.

When modifying the password in the Lorex Cloud Client, which password should I enter?

Enter the password for your Wi-Fi camera or accessory created in the Lorex App during setup.

.

Where can I order the Lorex Fusion Collection?

To order, go to lorex.com.

Lorex Fusion: Troubleshooting

The following article provides some troubleshooting tips for setting up your Lorex Fusion Collection.

.

My Fusion Wi-Fi camera or accessory is not appearing in the device list.

.

My Fusion Wi-Fi camera or accessory is not connecting to my Fusion recorder.

• Give your Fusion Wi-Fi camera or accessory a few minutes to establish a connection.

• Check to see if your Fusion recorder has the most up-to-date firmware. New Local UI: Login to your recorder and navigate to System > Update & Reset > Upgrade, then click Check for Updates.  Previous Local UI: Login to your recorder and navigate to Main Menu > Information > Update/Reset > Update, then click Check for Updates. For instructions on updating your recorder’s firmware through USB, see the article How to manually upgrade the firmware of your recorder.

• Ensure that your Fusion Wi-Fi cameras and accessories and your Fusion recorder are powered on.

• The same password created for your Fusion Wi-Fi camera or accessory in the Lorex App must be entered in your Fusion recorder. If you have forgotten the password, then reset your Fusion Wi-Fi camera or accessory and connect it to the app again.

• (Applies to the previous local UI only) If your password for your Fusion Wi-Fi camera or accessory is entered incorrectly in your Fusion recorder, then your Wi-Fi device will lock itself. Reset your Fusion Wi-Fi camera or accessory and connect it to the app again.

• Ensure that you are entering the password for your Fusion Wi-Fi camera or accessory created in the Lorex App, and not the Lorex App account password. Those are two separate passwords.

• Ensure that your Fusion Wi-Fi camera or accessory is connected to a dual-band router (2.4 GHz/5 GHz bands).

• Ensure that you are connecting the Fusion Wi-Fi camera or accessory to an available Fusion Wi-Fi channel, and not a Wi-Fi channel that already has a Wi-Fi device connected to it.

.

I don’t know the password for my Fusion Wi-Fi camera or accessory.

If you don’t know the password for your Fusion Wi-Fi camera or accessory, then you will need to reset the device and connect it to the Lorex App again.

To reset your Fusion Wi-Fi camera or accessory:

.

I’m receiving duplicate notifications in the Lorex App.

After completing the Fusion setup, your Wi-Fi camera or accessory is connected to the Lorex App twice – once as a single device and then a second time as a device connected to your recorder. To avoid receiving duplicate notifications from the same camera or accessory, you will need to Turn off Alerts for your Wi-Fi device connected to your recorder. For instructions, please see the article Lorex Fusion: Adjust Settings.

Lorex Fusion: Connect Your Wi-Fi Cameras and Accessories (N910 Series)

The following article provides instructions for connecting your Lorex Fusion Collection Wi-Fi Cameras and Accessories to your N910 Fusion recorder.

.

Our Lorex Fusion recorders incorporate the newest (fusion) technology to connect both wired and Wi-Fi cameras, doorbells, floodlights, and motion sensors to one system. All Fusion compatible Wi-Fi cameras and devices connect to one recorder for continuous 24/7 recording and private local storage. Access everything from the Lorex App for easy control of all devices.

Note: To conserve battery life, Wi-Fi Battery Video Doorbells only record when motion is detected. They do not record continuously.

For any connection issues, see the article Lorex Fusion: Troubleshooting.

.

Part One — Wired Setup

Setup your Fusion recorder and wired cameras. For Basic System Setup instructions, refer to your recorder’s Quick Start Guide or Manual on the product support page. Visit help.lorextechnology.com and search your Fusion recorder’s model number.

Important: Network setup is required for your system — use the included Ethernet cable to connect your recorder to your router.

.

Part Two — Connecting your Lorex Fusion Wi-Fi Camera

Connect your Lorex Fusion Wi-Fi Camera to the app and then from your recorder scan your network to add it.

.

Option A — Connecting Your New Lorex Fusion Wi-Fi Camera to Your Recorder

Add compatible Lorex Fusion Wi-Fi Cameras and Accessories onto Fusion Wi-Fi channels on the recorder.

To connect your New Lorex Fusion Wi-Fi Camera to the recorder:

Note:

.

Option B — Connecting Your Existing Lorex Fusion Wi-Fi Camera to Your Recorder

Add compatible Lorex Fusion Wi-Fi cameras and accessories onto Fusion Wi-Fi channels on the recorder.

Note:

To enable remote viewing for the mobile app, you will need to:

To connect your Existing Fusion Wi-Fi camera to the recorder:

1.From the Live View display, click the pair icon  in the center of the Fusion Wi-Fi channel’s screen.