1. Wi-Fi Range Extender:

2. Mesh Wi-Fi System:

3. Powerline Adapters:

4. Reposition Your Router:

5. Upgrade Your Router’s Antenna:

6. Consider a Wired Connection:

Important Tips:

Alternative

Extending WiFi coverage to support an outdoor wireless security camera requires ensuring a strong and stable signal in the camera’s location. Here are practical methods to achieve this:

1. Position the Router Strategically

2. Use a WiFi Extender or Repeater

3. Install a Powerline Adapter with WiFi

4. Upgrade to a Mesh WiFi System

5. Use a Dedicated Outdoor Access Point

6. Upgrade the Camera’s WiFi Antenna (If Removable)

7. Check for Interference

8. Switch to a Wired Connection

9. Test Signal Strength

Would you like guidance on selecting specific equipment or troubleshooting signal issues?

By considering these options, you can effectively extend your Wi-Fi range and ensure a reliable connection for your outdoor security camera.

Deploying outdoor WiFi is always necessary for deploying outdoor wireless security cameras. There are many options for extending WiFi. The optimal choice depends on the places and environments in that outdoor wireless cameras are installed.

There are two advisable solutions to extend the WiFi just around your house’s outdoor perimeter within 100 meters (300 feet). A network extension to the remote location farther than 300 feet will need a point-to-point wireless bridge.

1. Near Site WiFi Extension to the Outdoor Wireless Security Cameras (up to 100 meters or 300 feet)

It’s hard for WiFi signals to penetrate wire-filled stucco walls or stone walls. To provide strong WiFi outside for the outdoor cameras, one WiFi extender installed outdoors would avoid the stifling impact of walls on WiFi signals. There are two kinds of products—Powerline WiFi extenders and outdoor WiFi access points—to provide WiFi outside the home.

1.1 Near Site Outdoor WiFi for Cameras: Powerline WiFi Extenders

If you install your outdoor wireless camera under your eaves or in the backyard, plugging in a powerline WiFi extender around is an excellent way to solve the outdoor WiFi issues. As the powerline adapters are rated as indoor devices, a covered patio or waterproof electric box is needed to stand the harsh outdoor environments.

TP-Link TL-WPAxx series powerline wireless adapter kit is the easiest solution, providing two powerline adapters. One adapter installed indoors relays the data from the network cable to the power line. The second adapter broadcasts the WiFi signal to your cameras. Refer to the Outdoor Solution Guide for the installation tutorial and examples. The complete introduction of Powerline adapters will help you understand whether this solution is suitable for you.

1.2 Near Site Outdoor WiFi for Cameras: Outdoor WiFi Access Points

If your patio is not enclosed or the outdoor wireless cameras are installed further from your home, you may need an outdoor access point. TP-Link offers Omada EAP series omnidirectional outdoor access points for outdoor WiFi. They come with IP67 or IP65 waterproof and dustproof housing and a -30–70°C (-22–158°F) operating temperature range. They are designed to protect the outdoor access points against harsh outdoor conditions.

According to the areas of deploying outdoor cameras, there are two deployment methods. The basics are listed below. Refer to Get Outdoor WiFi with Outdoor WiFi Access Points for more details. Go to the Outdoor Solution Guide for the installation tutorial and examples.

1.2.1 WiFi Outside for Relatively Small Areas

One or two outdoor WiFi access points are deployed to connect the outdoor wireless cameras in relatively small areas. With the included passive PoE adapter, connect the Omada outdoor access points with your existing router to simultaneously provide data and power using a single Ethernet cable.

1.2.2 WiFi Outside for Relatively Large Areas

Several outdoor WiFi access points are deployed to connect outdoor wireless cameras across relatively large areas. The PoE switches or passive PoE adapters connect the Omada access points with a single Ethernet cable. Omada Mesh technology can wirelessly connect to the outdoor access points without additional cable if some access points cannot link to LAN ports. With Mesh technology, the maximum distance of extending outdoor WiFi can be multiple hundreds of meters.

2. Remote Site Network Expansion (More than 100 m and up to 30 km)

You can use the Pharos CPE series directional outdoor wireless antennas to build a wireless bridge to expand the network for miles. It is perfect for remote surveillance systems covering vast areas. You can also broadcast the wireless signals with an additional wireless access point on the remote site when necessary.

Refer to Pharos Solution to discover what Pharos products can bring. Go to the Outdoor Solution Guide for the installation tutorial and examples of Pharos wireless products. Refer to How to Connect Your Cameras from a Long Distance for using fibers to connect remote cameras.

3. Summary of Extending WiFi to Outdoor Wireless Security Cameras

So, ready to install your outdoor wireless cameras and choose the best outdoor WiFi solution. Let us know your idea about the outdoor WiFi on social media with #tplinkoutdoor!

Related Tags :

“best long range wifi extender for outdoor security camera with thick walls”, “how to extend wifi signal to outdoor camera 100 feet away”, “how to weatherproof a wifi extender for outdoor use”, “outdoor wifi extender with ethernet port for wired camera connection”, “best mesh wifi system for extending wifi to outdoor cameras”, “how to connect wifi extender to Arlo/Ring/Nest outdoor camera”, “troubleshooting wifi connection issues with outdoor security camera”,

“improving wifi signal strength for outdoor camera in remote location”, “how to avoid wifi interference for outdoor security cameras”, “using a point-to-point wifi bridge for long distance outdoor camera connection”, “extending wifi to a detached garage for security camera without running wires”, “best outdoor wifi solutions for rural areas with weak internet connection”, “how to choose the right wifi extender for your outdoor security camera setup”

<p>The post How to Extend WiFi for the Outdoor Wireless Security Camera first appeared on NVR IPCAMERA SECURITY.</p>

The Indoor Camera Pro does its job even if the Wi-Fi goes down with built-in recording and Vivint Playback DVR*—which offers limitless recording for up to 10 days. And built-in storage means faster clip retrieval and smoother video playback. See what’s happening at home, no buffering required.

The Indoor Camera Pro’s elevated night vision, field of view, and image quality create a clearer picture—day and night. Housed in a new sleek design with more flexible mounting and placement options, set up the camera nearly anywhere in your home to get the view you want. It’s next-level visibility, next-level protection.

Vivint Indoor Camera – Frequently Asked Questions

The Vivint Indoor Camera was previously known as the Ping Camera.

What is Privacy Mode?

Privacy mode allows you to temporarily disable your camera’s remote viewing and recording capabilities. While in Privacy mode, your camera will display a blue screen in your mobile app.    

Can I install a new camera or move my old one?

Normally a Vivint Smart Home Professional will install and position your Vivint Indoor Camera, but after installation you can move your cameras wherever you want. If you move your cameras or receive a new camera and would like to learn how to, see Vivint Indoor Camera – Installation Guide.

What do I do if my recording schedules aren’t working?

If your Vivint Indoor Camera’s schedules are not working, make sure that your camera is working and that the light on the front is green.

If everything is working, check and make sure that your schedules are turned on in the Recording Schedules section for your cameras.

If they still aren’t working, you may need to delete and recreate them. See Vivint Indoor Camera – Create Custom Recording Schedules.

How can I set up recording schedules for my Vivint Indoor Camera?

You’ll set up all recording schedules online. See Vivint Indoor Camera – Create Custom Recording Schedules.

.

Vivint Indoor Camera – Identify LED Meanings

The Vivint Indoor Camera was previously known as the Ping Camera.

White: Connected/normal operation

No Light: Privacy mode enabled or no power

Blue: Two-way talk

Green: Ready to connect

Yellow: Rebooting

Red: Not connected to the panel

Breathing White: Connected to the panel, but not connected to the internet

Vivint Indoor Camera – Landing Page

This article serves as an information hub for the Vivint Indoor Camera. The Vivint Indoor Camera was previously known as the Ping Camera.

Important Notes

Common Issues

For more detailed information about device specifications, click here. To review Frequently Asked Questions about this device, click here.

.

Vivint Indoor Camera – Offline

The Vivint Indoor Camera was previously known as the Ping Camera.

If your Vivint Indoor Camera shows it’s offline, you can take these steps to fix the issue.

Make sure the camera has power

Make sure the camera is plugged into a working outlet and the cord is securely plugged into the back of the camera.

To test the outlet, unplug the camera and plug a different device into the same outlet. If it also doesn’t receive power, try restoring power to the outlet.
Show me how

Reboot your panel

Takes 10-15 minutes.

Show me how

Restart your camera

Unplug your camera for 30 seconds, then plug it back in.

Restart your router

Unplug your router for 30 seconds, then plug it back in. If you have multiple routers or a separate modem, restart them as well.

Vivint Indoor Camera – Not Recording Clips

The Vivint Indoor Camera was previously known as the Ping Camera.

If your Vivint Indoor Camera is online and you are able to see the live feed, but it is not recording any clips, there are a few things you can check to fix the problem.

.

Vivint Indoor Camera – Installation Guide

Congratulations on your new Vivint Indoor Camera (formerly called the Ping Camera)! Let’s get it set up and integrated into your system right away. This article will walk you through the process, whether you are starting off fresh, or replacing an existing camera.

Low effort
Typically takes 5-10 minutes
Must be completed at home
You will need:

Disarm your system

Open Video in New Tab

Remove your existing Vivint Indoor Camera

*Skip this section if you’re not removing an existing camera.

If you’re replacing an existing camera, delete it from the panel by tapping: Menu, Devices followed by your 4-digit PIN, Cameras (select the device you want to remove), then Delete. Once deleted from the panel, physically remove it and return as instructed by Vivint.

Open Video in New Tab

Decide where you want your new camera

Make sure it’s within 200 feet of the panel and there are as few obstructions (walls, furniture, etc.) to line of sight as possible. You can either set your camera on a flat surface or mount it to a wall. To mount the camera, use the included screws and/or drywall plugs to mount the magnetic base plate, then attach the camera to the magnetic base.

Plug in your camera

It will take just a few minutes for it to boot up.

Go to your panel settings

From the home screen, tap the three dot Menu icon in the bottom right corner, tap Devices under SMART HOME SETTINGS, then enter your 4-digit PIN.

Open Video in New Tab

Add your Vivint Indoor Camera

Tap Add new device, then tap Vivint Indoor Camera.

Open Video in New Tab

Follow the prompts on your panel

Adjust camera settings as needed

From the panel, go to Devices, Cameras, then choose your new Vivint Indoor Camera and adjust the settings as desired.

Open Video in New Tab

Not working?

Unplug the camera for 30 seconds, then plug it back in. If you need additional assistance, please contact us.

Have more questions about your Vivint Indoor Camera and how to use it?

A library of content about your device, including general information, troubleshooting, and how to’s can be found here.

Vivint Indoor Camera – Initiate 2 Way Talk from the App

The Vivint Indoor Camera was previously known as the Ping Camera.

Your Vivint Indoor Camera enables you to stay connected to your home and family, even when you are away. When viewing the live feed of your Vivint Indoor Camera, you will be able to hear what is going on in the home. If you would like to initiate the two-way talk feature from the Vivint Smart Home app, follow the steps below. 

Vivint Indoor Camera – Enable Motion Triggered Clips

The Vivint Indoor Camera was previously known as the Ping Camera.

If you would like your Vivint Indoor Camera to record a clips when motion is detected, you can enable motion triggered clips from your Vivint Smart Home app by following these steps:

Vivint Indoor Camera – Adjust Video Motion Detection

This article explains how to adjust the video motion detection settings for your Vivint Indoor Camera. The Vivint Indoor Camera was previously known as the Ping Camera.

There are three settings that directly affect the motion detection performance of your Vivint indoor camera. Below is a description of what each setting is and how to optimize them.

To learn how to adjust your video motion detection settings, follow the steps below based on your panel type.

.

Vivint Indoor Camera – Enter Privacy Mode

The Vivint Indoor Camera was previously known as the Ping Camera.

Privacy mode allows you to temporarily disable your Vivint Indoor Camera’s remote viewing and recording capabilities. While in privacy mode, your camera will display a blue screen on your online account. To enter privacy mode, complete the following steps:

Vivint Indoor Camera – Test

The Vivint Indoor Camera was previously known as the Ping Camera.

When your Vivint Indoor Camera is installed and set up, you can test it to ensure it is working properly. You can test your camera from either your SkyControl panel or the Vivint Sky app. To test your camera, follow these steps:

From the SkyControl Panel

Vivint Indoor Camera – Initiate One-Touch Call Out

The Vivint Indoor Camera was previously known as the Ping Camera.

Want a quick and easy way to get in touch with your family? You can initiate the one-touch call-out feature on the Vivint Indoor Camera by following the steps below.

Vivint Indoor Camera – Delete and Re-Add

The Vivint Indoor Camera was previously known as the Ping Camera.

If your Vivint Indoor Camera camera shows as offline and you have already followed the troubleshooting steps here, you will need to delete and re-add your camera to your panel. Follow the steps below to learn how.
.

Delete your Vivint Indoor Camera from your panel 

Factory reset your Vivint Indoor Camera

Get the panel ready to add your Vivint Indoor Camera

Add your Vivint Indoor Camera

Vivint Indoor Camera – Create Custom Recording Schedules

The Vivint Indoor Camera was previously known as the Ping Camera.

You can create system-triggered recording or motion-triggered recordings for your Vivint Indoor Camera.

A system triggered recording means your cameras will start recording when an event is triggered by part of your system, i.e your panel, door locks, etc.

.

<p>The post Vivint Indoor Camera Setup and User Guide first appeared on NVR IPCAMERA SECURITY.</p>

This is a user guide for CMSClient version V1.00.00.47, it’s applied to software version is equal or newer than V1.00.00.47. If you are running older version (e.g. V1.00.00.46, V1.00.00.45), please download and upgrade your existing one to the latest. It should be noted that Yoosee has no app be compatible with Windows smartphone. If you have a smartphone running Windows OS, obviously you can not use Yoosee camera. The Yoosee software team will not release App for Windows based smartphone.

What CMSClient does?

CMSClient provides users a centralized video surveillance solution. It allows users to manage multiple cameras simultaneously, users can preview, record, playback, even receive alarm alerts by using it.  Users also can change yoosee camera’s network settings (such as IP address, gateway, DNS), can shift recording video resolution from SD to HD, can modify camera’s password.

Installation of CMSClient software

The software doesn’t contain any virus, if your anti-virus software report virus warning, please check if you have downloaded the software from official website. The software requires permission to access your network/Internet, it uses RTSP stream protocol to communicate with cameras locally, and P2P protocol to communicate with Internet cameras. When installing the software, ensuring it allows to pass Windows firewall.  The software will keep communicating with remote servers intending to establish P2P connection, it doesn’t spy your video, doesn’t transmit/upload any video clips to remote servers.

Logon CMSClient Software

CMSClient software now allows users to login through three different types of account.

• Admin login: local login, don’t require users to register an account. No need to input password, click “OK” to login immediately. The software can automatically discover local cameras, but can not discover Internet cameras.
• Phone Number login: remote login with your registered yoosee account, after logon, the software will list added cameras in your account.
• Mail/user ID login: remote login with your registered yoosee account, after logon, the software will list added cameras belongs to your account.

Moreover, select either “Phone number login” or “Mail/user ID login”, the software can receive motion detection (or sensor triggered) alert to computer. When motion detection alarm occurs, the software will pop-up a new window automatically to alert users, it also can play selectable audible automatically to remind users.

How to add Yoosee Cameras?

After logon, CMSClient will automatically discover local connected cameras, click “Add all” to add them into your software. Please note the displayed p2p password and rtsp password default is “qwe123”, it’s an incorrect password, just ignore them.

Except adding automatically, users can click “+” icon on the left bottom to manually add cameras. In “Device manager” window, local connected cameras will be listed on the left column, click “>>” button can add to software which will appear in right column. Click “Manual add device”, you can add local connected cameras via entering device ID, device password, RTSP password. Click”Add shared device” to add cameras as a guest user. In pop-up windows, you should paste the shared link. To know how to get shared link, you can read this article – How to use Yoosee App’s sharing function?

How to use CMSClient software?

Once you added devices to software, you’re able to use each functions of it. Select device you want to manage, right click mouse will pop-up a menu list.

• Device property: change camera name, device password, rtsp password and group.
• Delete node: delete camera from this list/software.
• Start monitoring: start to preview real-time video (if it shows you a crying face, it means password is incorrect)
• Smooth/standard definition/high definition: before click start monitoring, you should choose default image resolution, smooth equals low resolution, standard definition equals VGA (640×480), HD equals 1280×720 or 1920×1080.
• IPC config: you’re able to tweak camera’s network settings (e.g. IP address, DNS), record video resolution (SD, or HD), password.  It only works on the premise that your camera’s password is correct. If you encounter “network timeout” “permission error” “password incorrect” error, to solve this, you need to logon software with yoosee registered account.

CMSClient Playback Function

You’re able to playback recorded video clips right from your computer. The CMSClient can only allows users to play remotely and locally recorded video clips, but also can allow you convert them to friendly .mp4 files which can be recognized and played by regular media players.

Click “Search” button on the left top, the camera can search files, click the file name to playback. Additionally, you can click folder icon to open a file to play it. All yoosee camera will record video with .av file extension. These raw files can not be recognized or played by regular media players, you can use the converter which the software has included to convert .av files to .mp4 files.

If you don’t want to install and use CMSClient software, still want to play .av files in another computer, you can read this article – How to play .264 video files from IP cameras/DVRs/NVRs?

CMSClient software is a powerful video surveillance management tool, it includes other function to provide a great flexibility. Click gear icon on the top of software, it will pop-up a “CMS config” window.

• File save path: select the folder path to store recorded video footage.
• Reserve space: allowing users to modify reserved space for video storage in your HDD.
• Record time for package: the time length to patch a video file when recording video. If the value is “60” min, the software will patch/generate a video file in every hour when software is recording on computer.
• Cycle record: turn on/off over-write function, automatically erase/overwrite HDD when space is full.
• Auto start record when monitoring: record video while watch video stream.
• Connect all of device automatically: automatically display video for all cameras/channels after logon software.
• Render mode: Directdraw, GDI
• Monitor: auto, rtsp, p2p
• Message notification: choose whether receiving message notification or not when there is a motion detection alarm.

If you logon software with registered yoosee account, the software will have “Alarm trigger” option. This open allows you to select time length of pop-up video when alarm occurs. You’re able to choose different audio files, the computer will play the audio to remind users.

<p>The post User guide for Yoosee App PC Software – CMSClient first appeared on NVR IPCAMERA SECURITY.</p>

How to reset TVI DVR/ POE NVR / Wireless NVR (ZSWNVK-H) System when you forgot the password?

1) You can find the correct model number on the label at the bottom of the DVR / NVR System.

2) Find the DVR / NVR’s device ID/UID.

A. You can find the DVR’s ID on the label of the DVR / NVR.

How to reset Password Zosi DVR NVR Poe All Model

B. Or you can also reboot the DVR / NVR system and wait until Wizard Page display, then find the UID.

3) Please send us the model number and device ID / UID, we will create a super password for you.

    NOTE: The User Name corresponding to super password must be ‘admin’.

                 Once you set super password this time, the login password should be blank

                 in the next time when you reboot it or log in again.

                 You can go to DVR’s Main Menu – Setup – User – Change password to set a new

                 password. (Please keep the old password blank, you just need to input the new

                 password and confirm password.)

Beyond that, you can also upgrade software by means of upgrade file from us, then reset password when reboot DVR.

Connecting the DVR / NVR to the internet

This method works for the following models of DVRs / POE NVRs / Wireless NVRs:

4-Channel DVRs / POE NVRs / Wireless NVRs:

ZR04ZN;   ZR04ZM;   ZR04FN;   ZR04FM;   ZR04CN;   ZR04CM;   ZR04JS;   ZR04TS;   ZR04TN

ZR04RN;   ZR04RM;   ZR04EN;   ZR04EM;   

ZR04DS;   ZR04MS;  

8-Channel DVRs / POE NVRs / Wireless NVRs:

ZR08ZN;   ZR08ZM;  ZR08FN;   ZR08FM;   ZR08BN;   ZR08BM;   ZR08CN;   ZR08CM;   ZR08KS;   ZR08TN

ZR08RN;   ZR08RM;   ZR08EN;   ZR08EM;      

ZR08DS;   ZR08DP;   ZR08MS;   

16-Channel DVRs:

ZR16ZK;   ZR16JK;   ZR16BK;   ZR16CK

(You can find the model number on the label at the bottom of the DVR.)

If your CCTV DVR or NVR don’t have a built-in WiFi support, then you have to run internet cable (CAT 5 or CAT 6 Ethernet cable) to connect your DVR or NVR to the internet via the router.

• Connect one end of the Ethernet cable to the Ethernet input on the back of the DVR.
• Connect the other end of the Ethernet cable into a device providing an active internet connection, such as a router or modem.
• Test your internet connection to confirm that it is active by going to the Network > Network screen.

1) Right click mouse—go to Main Menu > Setup > Network.

2) On the Network tab, ensure the “Obtain an IP Address Automatically” option is enabled, and that there is no information in the PPPoE fields.

3) Once you’ve ensured there is no information in the PPPoE field and that the “Obtain and IP Address Automatically” option is selected, select the “Test” option.

If “OK” is displayed, the local area network is connected successfully.

If the DVR is not able to connect to the internet, you will get a message that states “Cannot Connect to Network”.

NOTE:

In order for other devices to connect to the DVR through the router, the DHCP setting must be enabled from the router’s settings page.

If you still cannot connect to the network, please ensure that you don’t have a firewall active on your network that may be limiting the connection.

You may need to open ports 80, 5000, and 5001 on your router, if they’re currently being blocked by te firewall. This typically only happens on commercial internet accounts, as they deal with sensitive transactions, but occasionally a firewall on a residential line will also block these ports.

If you’re unsure how to open ports on your router, you will need to speak with the router manufacturer.

FAQ:

1) What’s DHCP?

DHCP is a type of internet networking approach. It stands for Dynamic Host Configuration Protocol. It means that a router assigns IP addresses to each of the devices on the network, allowing them to communicate with other devices in or outside the network.

In context of our systems, the setting related to DHCP is called DHCP server status. This setting enables your router to obtain the static IP address on the DVR and broadcast that IP to the app so it can locate your DVR. This setting needs to be enabled on a router for the apps to be able to connect to the DVR systems.

2) For example: How to set up a linksys E5350 Router?

Once you’ve logged into the router settings, you’ll want to select “configuration” at the top, and then “Connection > Local Network” in the menu on the left. You should see this page:

​

You’ll want to ensure the checkbox beside “DHCP server” is checked off, and set the start IP address to 100 as shown in the image. Leaving the other settings here as they default should be fine. Once this is done, select “save.” Before proceeding with the next steps, try using the app while not connected to local WiFi. If you can see the live feeds, you don’t need to complete the steps below.

If you can’t, you’ll need to open the ports in the firewall. On the left menu, select “Security”, and then “Single Port forwarding” as shown in this image:

​

Select the button on this page for “Add a new Single Port Forwarding”, and this window should appear:

​

The number you want to enter in the “To IP Address” field is the last three digits of the DVR’s static IP, which you can find on the Network page of the DVR. (Main Menu > Setup > Network)

Application and protocol can be left as they are, and you’ll want to check off the “enabled” box. You’ll need to do this 3 times, using the following information:

1.
Application Name: DVR HTTP
External Port: 80
Internal Port: 80

2.
Application Name: DVR Mobile
External Port: 5000
Internal Port: 5000

3.
Application Name: DVR E-mail
External Port: 5001
Internal Port: 5001

After filling the box with the necessary info for each port, select “apply”, and then hit the add button again to reopen the window. Once all 3 ports are opened, try testing the app again.

Note:  different Routers may have different setting interfaces.

More questions, please feel free to contact us.

Our Whatsapp:  +1-866-841-6932

Support Email address:  service@zositech.com

Our Facebook:  https://www.facebook.com/ZosiTechnology/

Support center: support@zositechhelp.zendesk.com

<p>The post How to reset Password Zosi DVR NVR Poe All Model first appeared on NVR IPCAMERA SECURITY.</p>

How to reset the password of the VIGI camera?

If you forget the password of the VIGI camera, you can reset the password via VIGI Security Manager or VIGI NVR.

Method 1: Via VIGI Security Manager

Step 1. Click the Forget Password option.

If the camera is not added, go to Settings > Device > Device List > Discovered Devices, select the device and click the Set Password or + Add > Forget Password.

If the camera has been added, go to Settings > Device > Device List > My Devices > Settings icon of the camera > Basic Information > Device Security > Modify > Forget Password.

Step 2. Send the Verification Code to your Reset Password Email.

If the camera is connected to the internet, click the Send Code and you’ll receive a verification code sent to your Reset Password Email.

If the camera is not connected to the internet, please Download VIGI App in the App Store or Google Play. Scan the QR code with the app and you’ll receive a verification code sent to your Reset Password Email.

Step 3. Enter the verification code and click Next.

Step 4. Enter the new password.

Method 2: Via VIGI NVR

Step 1. Click the Forget Password option.

Right click to open Main Menu, go to Settings > Camera > Device Access > Add Device > Discovered Devices and you will see Forget Password option. If the camera has been added and is not certified, you need to remove the camera first.

Step 2. Send Verification Code to your Reset Password Email.

Step 3. Enter the verification code and click Verify.

Step 4. Enter the new password.

Note:

1. What’s the Reset Password Email?

When you first activate camera, it is asked to enter your Reset Password Email. It is only used to receive the verification code when you need to reset the password.

2. What should I do if I don’t receive the verification code?

TP-Link VIGI Cameras Ultimate Guide Part 4

How to modify the IP address of the VIGI camera

You can use the VIGI Security Manager or VIGI NVR to modify the IP address of your VIGI camera.

Via: VIGI Security Manager

If the camera is not added, go to Settings > Device > Device List > Discovered Devices, select the device and click the Set Network.

If the camera has been added, go to Settings > Device > Device List > My Devices > Settings icon of the camera > Network Settings > Connection and modify the IP address.

Via: VIGI NVR

If the camera is not added, go to Settings > Camera > Device Access> Add device, select the device and click the Modify IP address.

If the camera has been added, you can modify the IP address via one-click networking option. Go to Settings > Network > Connection and click the one-click networking.

Select the device you want to change and NVR will assign unassigned IP. In this way, you can manually set the IP address. If you want to manually set the IP address, you need to remove the camera and change the IP address before it is added.

How to avoid the overexposure of image

The overexposure of surveillance images can be roughly divided into over-exposure during the day and overexposure at night. The overexposure in the daytime is basically caused by the backlight of the scene, while the overexposure at night is caused by the over-intensity of the infrared reflected light of the object.

Note: Please make sure the lens is clean.

Overexposure in the daytime

The light reflected from the counter is relatively strong, making the counter very bright and unclear

The camera will overexpose in the presence of bright light directed or reflected into the lens. Overexposure will lead to unclear details. During installation, we need to consider scenarios and avoid direct light or strong reflections. If it is unavoidable, we need to adjust the image parameters to alleviate the overexposure.

Step 1: We take the overexposure area as the exposure target and do backlight compensation (BLC), so that the IPC takes the overexposure area as the target to reduce the overall light input. The overexposure area in the figure is near the center, and we set BLC area to be center.

Step 2: After we enable BLC, the IPC reduces the overall light input, so the surroundings will become darker. We can increase the brightness of the surroundings by wide dynamic range (WDR).

Step 3: We can fine-tune brightness and contrast to display the best image.

The following picture shows the adjusted result. (BLC area in center + WDR + brightness 60, contrast 40.) As you can see, the area of counter is clearer. You can further adjust the parameters according to your own image quality.

Overexposure at night

Overexposure due to being next to the wall is quite obvious, as shown below.

When the camera is installed next to the wall, if the angle is too biased towards the wall, the infrared light reflected back from the wall will be too strong, and the wall will be overexposed. If the wall is overexposed, the camera will reduce the shutter exposure time to maintain the overall average brightness of the screen, so that the other part of the screen will be too dark.

Step 1. Adjust angle to reduce the area of overexposed objects in the picture.

Without affecting the monitoring, make the wall area in the picture as small as possible. Firstly, the effective monitoring area can be increased; secondly, if the overexposure area of the wall is reduced, the exposure time of the camera will be increased, and the monitoring image will be clearer.

Step 2. Set BLC area to make dark areas brighter

You can increase the exposure time of the camera by setting the BLC area of the camera. Although the wall or reflective obstacles may be brighter, the effective monitoring area can be seen more clearly.

Step 3. Enable WDR to balance the brightness

Increase WDR can strengthen the details in the dark, and monitoring effect in night vision is better.

Note: Too high WDR will increase the noise in the night vision picture. WDR should be properly increased.

How to upgrade the firmware of VIGI cameras

Method 1: Via the VIGI app

1. On the Live View page, tap the gear icon to enter the Device Settings page.

2. On the Device Settings page, tap on the Firmware Upgrade to check for update or update the firmware.

Method 2: Via the VIGI Security Manager (Windows only)

1. Open the VIGI Security Manager.

2. Go to the Settings page and go to Device > Device Upgrade to update the firmware.

What is the difference between 2.8 mm, 4 mm, 6 mm and 8 mm lens?

Lens focal length tells us the angle of view—how much of the scene will be captured—and the magnification—how large individual elements will be. The lager the focal length, the narrower the angle of view and the higher the magnification.

VIGI indoor cameras have a focal length of 2.8/4 mm and VIGI outdoor cameras have a focal length of 4/6 mm. The last digit of the model indicates the focal length of the lens.

For example:

VIGI C400HP-4: The focal length is 4 mm.

VIGI C300HP-6: The focal length is 6 mm.

How to select suitable lens?

The larger the focal length of the lens, the smaller the angle of view, and the farther the monitoring distance. So the camera lens with low focal length is suitable for observing small areas where need a wide angle. If you want to observe the objects closer with a big distance, you’d better select the cameras with a lager focal length lens.

How to rotate the image of my VIGI camera

You can rotate the image via VIGI App, VIGI Security Manager or VIGI NVR. VIGI Security Manager and VIGI NVR has more mirror option than VIGI App.

Here we take VIGI C400HP-4 as an example.

Method 1: Via VIGI App

1. On the Live View page, tap the gear icon to enter the Device Settings page.

2. On the Device Settings page, go to Device Control > Video Rotation.

3. On the Video Rotation page, you can select Upside Down to rotate the video image 180°.

Method 2: Via VIGI Security Manager

1. Go to Settings > Device > Device List > My Devices and click the settings icon of the camera.

2. Go to Image > Mirror and select Mirror option you want.

Method 3: Via VIGI NVR

Right click to open Main Menu, go to Settings > Camera > Display > Image > Advanced Settings, select Mirror option you want.

How to change the password and Reset Password Email of the VIGI camera

You can change the password and Reset Password Email of the VIGI camera via VIGI Security Manager or VIGI NVR. Reset Password Email is used to receive the verification code when you need to reset the password.

Method 1: Via VIGI Security Manager

Step 1. Go to Settings > Device > Device List > My Devices and click the settings icon of the camera.

Step 2. Go to Basic Information > Device Security and click Modify to change the password and Reset Password Email.

Note: If you forget the old password, please refer to the link to reset the password.

Method 2: Via VIGI NVR

Step 1. Right click to open Main Menu, go to Settings > Camera > Device Management > Password Management, select the camera and click edit icon.

Step 2. Enter your new password and Reset Password Email, click Save. You can also use Preset IPC Settings which you set on the VIGI NVR. If you want to change the preset IPC settings, you can refer to the link.

.

<p>The post TP-Link VIGI Cameras Ultimate Guide Part 4 first appeared on NVR IPCAMERA SECURITY.</p>

How to Mount Your VIGI Pan & Tilt Camera to a Wall or Pole

This article will show you how to mount your camera to the wall, and how to remove your camera from the camera base.

How to Mount Your Camera

1. Mark Position

Place the mounting template where you want the camera. For wall mounting, drill four holes through four circles on your mounting template.

2. Mount Base or Pole Mounting

Mount Base:

Affix the camera base using the screws.

For wall mounting, insert four anchors into the holes and use the self-tapping screws to affix the camera base over the anchors.
There are two ways to install your cameras by the mount base depending on your situation.

Method 1:

Method 2:

Pole Mounting:

Use the cable tie to attach and tighten your camera to the pole.

How to Uninstall Your Camera

If you mounted it on the wall

Remove the screws from the anchor. Then you can take your camera off the wall.

If you install it to a pole, remove the cable ties and you can uninstall it.

How to use VIGI cameras with other NVR brands or NAS

The VIGI cameras work with VIGI NVR as well as other NVR brands or NAS for easier batch access and management. It is recommended to use the VIGI cameras with the VIGI NVR. For other NVR brands, make sure they support ONVIF and RTSP protocols. Here we will show you how to use VIGI cameras with other NVR brands.

Step 1: Power on your cameras and connect them to the same network as your NVR.

Step 2: Activate the cameras using the VIGI Security Manager or VIGI App.

1. Download the VIGI Security Manager on your windows computer at https://www.tp-link.com/download-center/

2. Install the VIGI Security Manager and open it.

3. Go to Settings > Discovered Devices. Cameras on the same network as your computer can be automatically discovered.

4. Click + Add to activate your discovered cameras by setting passwords.

5. Follow the instructions to add your cameras.

Step 3: Refer to the NVR’s User Manual to add cameras.

We will show you some basic parameters that it may require to connect the VIGI camera to your NVR.

1. The IP address of the camera.

Open VIGI Security Manger and go to Settings > Device > Device List > My Devices > Settings icon of the camera > Network Settings > Connection.

For some NVRs, you’ll need to modify the IP address of the VIGI camera to the same network segment as the NVR for successful adding.

2. The ports for standard ONVIF and RTSP protocols.

Please select Onvif protocols to add VIGI cameras.

ONVIF Service Port: 2020

RTSP Service Port: 554

3. The username/password of the camera.

Username: admin

Password: It is set when you activated the camera. If you forget it, please refer to the link to reset the password.

What should I do if VIGI camera is not found?

This article is to solve the problem that VIGI camera is not found. Please check the steps below:

Step 1. Confirm that the camera is powered up.

The camera should be powered up via 12V DC adapter or PoE (802.3af/at). The IR LED will turn on for 20 seconds once the camera is powered on.

Step 2. Confirm that the camera is connected to your network properly.

The camera should be connected to network devices via Ethernet cable.

Step 3. Make sure your device is on the same network as the camera.

Step 4. Reboot your network devices including router and refresh to discover your cameras again.

Step 5. Try other methods to discover devices.

You can try to discover devices via VIGI Security Manager, VIGI NVR or VIGI App.

How to Verify Fake Micro SD Cards When Using with VIGI Cameras

Note:

A security camera that works with a standalone microSD card is primarily designed to store motion-activated recordings or short video clips of movements with local storage, which offers a cost-effective alternative to the subscription-based cloud storage. However, users may run into issues like the camera is unable to overwrite recordings, the SD card becomes full and stops recording or the SD card cannot be formatted by the camera App, etc. These kinds of problems might be caused by the fake SD card.

Micro SD Card and fake SD Card

An SD Card is a small electronic storage medium used by a plethora of storage devices including smartphones, games devices, camcorders, and cameras. Most of the smartphones and security cameras are using the microSD card.

The TP-Link camera supports a microSD card with up to 512GB capacity. If the remaining space of an SD card is less than 500MB or 5% of the total capacity before the first insertion of the camera, it would be impossible to record. There are different speed specifications for microSD cards and it is recommended to use a card with Class 10 or UHS 1 speed rating, which requires a minimum writing speed of 10MB/s.

The most common fake microSD card is the fake capacity expanded card, which uses illegal means and tools to make the cards with a small capacity appear larger. For example, a 32GB card is displayed as 128GB on your computer or other devices. This kind of card is usually having a lower price than the official quality goods. Since the capacity is Manual deceived by the illegal means and tools so that the space beyond the original capacity cannot be used normally.

If the stored file exceeds the actual capacity, the file will be unavailable. Our camera recognizes the microSD card and will format it in Fat32 format and creates index files to save your video data. This process reads and writes the entire space of the SD card and checks whether it is valid. If your SD card is an expanded card, it will not be formatted successfully and will not work properly on our camera.

We do not support the card due to the particularity of the monitoring camera; we need to ensure that the SD card can work stably for a long time. And since camera data is relatively important, data loss or failure to write data can have a significant impact.

Note: For VIGI cameras, it is required to format the SD card on the VIGI app for local recording.

Comparison of SD card Speed Class ratings

Types of Fake SD cards

When it comes to counterfeit memory cards, you will find some different types of them like listed below:

1. Reduced Read / Write Speed: You buy an SD card that shows something like “maximum 95 MB/s read and 90 MB/s write speed” and a “V30” label that is supposed to guarantee a minimum writing speed of 30 MB/s. But when copying a file using a fast SD card reader, you might not even get more than 5-10 MB/s.

2. Reduced Capacity: The SD card might report a large capacity when inserted in your computer, camera, or storage device, while it contains only a very small part of the overall capacity. This happens because the microchip (a tiny part of the SD card that is responsible for reporting the total amount of storage available) within the card has been reprogrammed to report a different size to the host. Counterfeit SD cards with reduced capacities should be avoided the most because they will most certainly result in data loss.

3. Fake Brand: Some SD cards have big brand labels attached to them and sold at a premium price when they are made from cheap parts by some unknown manufacturer. Such products are often more difficult to identify and might require a call to the manufacturer to verify the serial number. You can also read the reviews posted by verified buyers on Amazon or other online stores.

4. Unrealistic Capacity: There are memory cards that advertise completely unrealistic storage sizes. For example, if you search online for microSD cards, you may find cards with capacities as large as 2TB, however, such capacities do not yet exist.

5. Bogus / Non-Working: Some SD cards are sold at incredibly low prices by unknown sellers and may just don’t work.

Fake SD Card Issues

As you can see from the earlier section, the issues can range from getting very slow speeds to data loss and unusable SD cards. The problem with fake SD cards with reduced capacity is that when users go over a certain capacity, all data from that point on will be corrupted. Everything appears to be working great at first, but troubles may show up in later usage.

How to Identify a Fake SD Card

If you have already purchased an SD card, there are a few things you can inspect and basic tests you can run to identify a fake SD card.

1. Inspect Product Packaging: Make sure the package contains necessary information about the product such as its specifications and card speed, as well as all the appropriate labels, warranty info, and a proper UPC. Users may also verify with SD card manufacturer directly.

2. Test the SD card with third-party software: Make sure you format the SD card before you start this step. For example, you could verify if you can write files to the advertised capacity for your SD card with software H2testw. Install the H2testw on your Windows computer (you can also run a similar tool called “F3” on Mac OS, and an app called SD Insight on Android device) and run the test, it will show you the real capacity of your SD card.

If the SD card you are using is fake, it will report errors and show how much actual data was written and read from the card.

Memory Card Buying Tips

Sum up the article with the below memory card buying tips:

· Always make sure to buy from an authorized seller.

· Be careful about cheap SD cards.

· Always inspect and test each card to make sure that it is genuine.

· Do not buy used or refurbished SD cards.

· Replace SD cards once every few years to reduce potential failure.

A list of microSD card we have tested:

.

How to Waterproof VIGI Outdoor Security Cameras

When the camera is installed outdoors, please install waterproof items to waterproof your VIGI outdoor security cameras. Make sure each part is securely attached and the water-proofing rings are flush to keep out water.

Step 1: Install Waterproof Cable Attachments

Install the waterproof cable attachments for the network interface when the camera is installed outdoors.

Done! The network interface is now waterproof.

Step 2: Install Waterproof Seal for Power Connectors

Install the waterproof seal for the power connectors when the camera is installed outdoors.

What to do when the image of VIGI Camera is misty and hazy on the Night Vision

This article aims to optimize the image quality when it looks misty and hazy in night vision mode.

As shown in the above image, sometimes we may notice that the camera display appears to be covered with a layer of silk, or like fingerprints on the lens, making it particularly blurry and difficult to see anything in night vision mode.

Generally speaking, there are several reasons that can cause abnormal image:

To optimize the camera performance and ensure clear image quality:

By following these steps, you can improve the clarity of the camera’s display and ensure better surveillance performance.

How to configure VIGI camera’s exposure parameters

This article discusses how to adjust the exposure parameters of VIGI Cameras using the web interface or VIGI Security Manager to achieve better image quality in different environments.

Exposure refers to the amount of light entering the camera. Overexposure in surveillance images results in a too bright image, while underexposure leads to a dark image that lacks clarity.

Overexposure can generally be divided into overexposure during the day and overexposure at night. Overexposure during the day is mainly caused by backlighting in the scene, while overexposure at night is caused by excessive infrared reflection from objects.

Underexposure, on the other hand, is primarily due to low ambient brightness, resulting in insufficient light entering the camera.

To address the above issues, we can make adjustments through Exposure setting, Prevent Overexposure setting, as well as BLC (Backlight Compensation) and WDR (Wide Dynamic Range) settings to obtain more suitable image effects for specific scenes.

Exposure settings include exposure gain and shutter speed. Higher gain and slower shutter speed allow more light to enter the camera within the same time frame, resulting in a brighter image, and vice versa for a darker image.

Prevent overexposure, the brightness of the infrared illuminator can be adjusted to avoid excessive infrared reflection at night.

In addition, there are WDR settings and BLC settings. WDR processes the dark and bright areas of the image to make the dark areas brighter and the bright areas darker, thus achieving better image quality in environments with high contrast between highlights and shadows. BLC targets specific backlight areas and adjusts the light entering the camera accordingly to achieve the desired image effect.

Next, we will explain how to adjust these parameters through VIGI Security Manager and the camera’s web interface.

Configuring through VIGI Security Manager:

Configuring through the web interface:

General questions about halos on the VIGI Camera’s screen

Have you ever noticed large, irregular halos on your device’s screen, especially after rain or in damp weather? These can significantly disrupt your viewing experience. This article will explain why this happens and how to fix it. By understanding these common screen distortions, you can take the necessary steps to maintain the quality of your device’s.

Q1: What causes the appearance of large, irregular halos on my screen as below picture?

A: This issue is typically caused by dirt or contamination on the lens or casing of your device. Common culprits include fingerprints or condensation, which can lead to irregular reflections. These reflections then manifest as large, irregular halos on your screen.

Q2: How can I resolve this issue?

A: To rectify this, it’s important to regularly check the condition of your device’s lens and casing. Wiping the lens with a dry cloth can help keep it clean, reducing the likelihood of these halos appearing.

In the course of normal device usage, you might also notice glare or ghosting effects on your screen as below. The following section will explain these phenomena.

Q3: What are glare and ghosting effects?

A: Glare is a phenomenon that occurs around a light source, taking a shape similar to the light source, complete with a halo and radiating light beams. Ghosting, on the other hand, forms a light cluster at a different location that resembles the light source.

Q4: Why do these phenomena occur?

A: Both glare and ghosting occur when the point light source is too strong, causing light reflected from the lens surface to repeatedly reflect within the camera. These reflected lights cover the screen, reducing contrast and causing local obstruction, ultimately presenting as halos on the screen.

Q5: How can I resolve this issue?

A: To avoid these issues, consider the following methods:

1. Keep the lens clean. Dust or oily fingerprints on the lens can intensify ghosting and glare.

2. Use a lens hood.

3. Change the light source or shooting location.

4. Try to avoid shooting directly into the sun.

<p>The post TP-Link VIGI Cameras Ultimate Guide Part 3 first appeared on NVR IPCAMERA SECURITY.</p>

Introduction

Mobotix cameras are known for their high-quality imaging and advanced surveillance capabilities. Whether you are using them for home security or professional monitoring, understanding how to set up and use these cameras is essential. This guide will provide comprehensive instructions, tips, and insights on Mobotix camera setup and usage to ensure you get the most out of your surveillance system.

Table of Contents

.

Understanding Mobotix Cameras

What Makes Mobotix Cameras Unique

Mobotix cameras stand out in the surveillance industry due to their decentralized architecture. Unlike traditional cameras, Mobotix cameras process and store data internally, reducing the need for external storage and processing power. This results in a more reliable and efficient surveillance system.

Types of Mobotix Cameras

Mobotix offers a variety of cameras designed for different applications. These include:

Unboxing Your Mobotix Camera

What’s Included

When you unbox your Mobotix camera, you will find the following items:

Initial Inspection

Before starting the installation, inspect the camera and all components for any signs of damage. Ensure that all items listed in the manual are present.

Preparing for Installation

Choosing the Right Location

Selecting the optimal location for your Mobotix camera is crucial for effective surveillance. Consider areas with clear views of the intended monitoring space, minimal obstructions, and appropriate lighting conditions.

Required Tools and Accessories

To install your Mobotix camera, you will need:

Installing Your Mobotix Camera

Mounting the Camera

Begin by securing the mounting bracket to the chosen surface using the provided screws and anchors. Attach the camera to the bracket and adjust its position as needed.

Connecting to Power

Mobotix cameras can be powered using traditional power supplies or PoE. Connect the power cable or Ethernet cable to the camera and ensure a secure connection.

Securing the Setup

Double-check all connections and ensure that the camera is firmly mounted. Avoid loose cables that could be tampered with or damaged.

Network Configuration

Connecting to Your Network

Connect the camera to your network using an Ethernet cable. Ensure the camera is within range of your router or network switch.

Configuring IP Settings

Access the camera’s web interface to configure its IP settings. Assign a static IP address to ensure consistent connectivity and avoid IP conflicts.

Setting Up the Mobotix Software

Downloading and Installing Software

Download the Mobotix software from the official website. Follow the installation instructions to set up the software on your computer or mobile device.

Initial Software Setup

Open the Mobotix software and follow the prompts to add your camera. Configure basic settings such as date, time, and camera name.

Accessing Your Camera Remotely

Remote Access Setup

To access your camera remotely, configure port forwarding on your router. This allows you to view your camera’s feed from anywhere with an internet connection.

Using Mobotix Mobile Apps

Mobotix offers mobile apps for both Android and iOS devices. Download the app, log in with your camera’s credentials, and access live feeds and recorded footage on the go.

Configuring Camera Settings

Adjusting Image Quality

Within the camera’s settings, you can adjust the image resolution, frame rate, and compression to suit your needs. Higher resolution and frame rates provide clearer images but require more storage.

Motion Detection Settings

Enable motion detection to receive alerts when movement is detected within the camera’s field of view. Configure sensitivity and detection zones to reduce false alarms.

Notifications and Alerts

Set up email or push notifications to alert you when motion is detected or other events occur. Customize the alert settings to receive timely updates.

Integrating with Other Systems

Connecting to NVRs and DVRs

Mobotix cameras can be integrated with Network Video Recorders (NVRs) and Digital Video Recorders (DVRs) for centralized storage and management of video footage.

Integration with Home Automation

Integrate your Mobotix camera with home automation systems like SmartThings or Amazon Alexa for enhanced functionality and control.

Troubleshooting Common Issues

Connectivity Problems

If you experience connectivity issues, check your network settings, cables, and power supply. Restarting the camera and router can often resolve these problems.

Image Quality Issues

Ensure the camera lens is clean and unobstructed. Adjust settings for lighting conditions and check for firmware updates that might improve performance.

Software Errors

Reinstall the Mobotix software if you encounter persistent errors. Contact Mobotix support for assistance if problems continue.

Maintenance and Upkeep

Cleaning the Camera

Regularly clean the camera lens and housing to ensure clear images. Use a soft, dry cloth to remove dust and debris.

Firmware Updates

Check for firmware updates periodically to keep your camera up to date with the latest features and security enhancements.

Regular System Checks

Perform regular checks on your camera system to ensure all components are functioning correctly. Test connections, image quality, and motion detection settings.

Advanced Features of Mobotix Cameras

Thermal Imaging

Mobotix thermal cameras detect temperature variations, useful for identifying heat sources and monitoring environments where temperature control is critical.

Advanced Analytics

Utilize advanced analytics features such as object tracking, heat mapping, and behavioral analysis to enhance your surveillance capabilities.

Audio Capabilities

Many Mobotix cameras include audio input and output, allowing for two-way communication and audio recording.

Security Best Practices

Securing Your Camera Network

Protect your surveillance network by using strong passwords, enabling encryption, and regularly updating firmware and software.

Data Encryption

Encrypt stored and transmitted data to prevent unauthorized access. Use secure protocols such as HTTPS and SSL for data transmission.

User Access Management

Limit access to your camera system to authorized users only. Assign different access levels based on roles and responsibilities.

User Guide for Everyday Use

Live Monitoring

Monitor live feeds from your Mobotix camera using the software or mobile app. Use the PTZ (pan-tilt-zoom) features to focus on specific areas of interest.

Reviewing Footage

Access recorded footage through the Mobotix software. Use search and playback functions to find and review specific events.

Exporting and Sharing Videos

Export video clips for sharing or storage using the software. Choose appropriate file formats and resolutions for your needs.

Mobotix Camera Accessories

Additional Lenses

Expand your camera’s capabilities with additional lenses for different focal lengths and viewing angles.

Mounting Options

Choose from various mounting options such as wall mounts, ceiling mounts, and pole mounts to suit your installation requirements.

External Storage Solutions

Use external storage solutions like NAS (Network Attached Storage) devices for extended video storage and backup.

Comparing Mobotix Models

Key Features of Popular Models

Compare key features of popular Mobotix camera models, such as resolution, frame rate, and special functions.

Best Use Cases for Each Model

Identify the best use cases for each Mobotix model based on features and specifications. Choose the right camera for your specific surveillance needs.

Case Studies and Applications

Real-World Examples

Explore real-world examples of Mobotix camera installations and their impact on security and surveillance.

Industry-Specific Uses

Learn how different industries utilize Mobotix cameras, from retail and healthcare to industrial and educational settings.

Customer Support and Resources

Contacting Support

Reach out to Mobotix support for assistance with technical issues, installation questions, or warranty inquiries.

Online Resources

Access online resources such as user manuals, installation guides, and troubleshooting tips on the Mobotix website.

User Communities

Join Mobotix user communities and forums to share experiences, seek advice, and stay updated on the latest developments.

FAQs

What is the warranty period for Mobotix cameras?

Mobotix cameras typically come with a three-year warranty, covering defects in materials and workmanship.

Can Mobotix cameras be integrated with third-party software?

Yes, Mobotix cameras are compatible with many third-party surveillance software solutions, allowing for flexible integration.

How do I reset my Mobotix camera to factory settings?

To reset your Mobotix camera, locate the reset button on the device, press and hold it for about 10 seconds until the camera reboots.

Are Mobotix cameras weatherproof?

Many Mobotix models are designed to be weatherproof and can withstand harsh environmental conditions, making them suitable for outdoor use.

What types of storage options are available for Mobotix cameras?

Mobotix cameras support various storage options, including internal SD cards, external NAS devices, and cloud storage solutions.

Can I view my Mobotix camera feed on my smartphone?

Yes, you can view live and recorded footage from your Mobotix camera using the Mobotix mobile app, available for both Android and iOS devices.

Conclusion

Summary of Key Points

Setting up and using Mobotix cameras involves several steps, from installation and network configuration to advanced settings and maintenance. By following this comprehensive guide, you can ensure a successful surveillance system that meets your security needs.

Final Tips

Always keep your camera firmware and software up to date, regularly check and clean your cameras, and utilize the advanced features to maximize your surveillance capabilities.

.

<p>The post Mobotix Cameras setup and detailed guide v3 first appeared on NVR IPCAMERA SECURITY.</p>

FLEX AI: Get started

Summary:

FLEX AI enables you to enhance camera capabilities, enabling them to detect and track previously unidentifiable objects. While many cameras can detect and track people and specific vehicle types, it is a different matter identifying shopping carts, forklift trucks, hovercrafts, or items on a conveyor belt.

With FLEX AI you can create custom object detection models for solid objects that can then be deployed to cameras, enabling you to detect objects that standard analytics does not already detect.

It is a cloud-based application, and its results are compatible with deployment to P-series AI cameras.

How it Works:

FLEX AI operates on a subscription-based model, granting users comprehensive access to train, process, and download custom detection models for end customers. However, the allocation of licenses requires a careful consideration of each end customer, with a separate FLEX AI license needed for each one. This process is typically managed by a STEP Partner, who oversees the distribution of licenses to ensure effective deployment.

For actual deployment onto cameras, FLEX AI uses a perpetual licensing system, distinct from its subscription model. Each camera necessitates its own perpetual license to run FLEX AI models effectively. This approach ensures that users can deploy and utilize the models on their cameras without the constraints of a subscription-based licensing system.

In terms of training models, FLEX AI currently supports the MP4 format or tagged WAVE Sync videos for training.

NOTE: Each project can only train one model.

Camera Compatibility:

Refer to the following article: Which Cameras are Compatible With FLEX AI

Note: Each camera can only run one FLEX AI model, although it may run in parallel with WiseAI.

The FLEX AI Flow:

The general process is as follow:

FLEX AI: What do I need to train a model with FLEX AI?

Summary:

This article covers what you need to build effective models with FLEX AI.

Training Requirements and Recommendations:

NOTE: After you click Train, the data you have created is sent to the cloud and
the algorithm is trained to detect your object. This process can take anywhere
from 30min to 1 hr and depends on the number of training images you included.

Performance Issues:

The following may cause object detection to have performance issues:

Camera Recommendations

Limitations:

FLEX AI has the following limitations:

Processing Times

FLEX AI: How do I create and manage FLEX AI projects?

Summary:

This article provides instructions for creating and managing FLEX AI projects.

Step By Step Guide:

Creating New Projects

To create a new FLEX AI project:

1. On the Project screen, click the plus (+) button to create a new project.

2. Name your project after the detection type.

NOTE:
Project names must be unique.
Each project can only consist of one object detection type.

Managing Projects

Here is an example of multiple projects being worked on in parallel.

To search for a FLEX AI project:

Existing projects will indicate their current status:

FLEX AI: How do I add a video clip for FLEX AI usage?

Summary:

This article describes the process for uploading training video clips to train a FLEX AI model.

Step By Step Guide:

Uploading a video

NOTE: The Video Library drawer can be expanded and collapsed by clicking the arrow.

Pulling bookmarked videos directly from WAVE Sync

NOTE: First tag WAVE Sync bookmarks with “flex_ai” to make them to appear in FLEX AI.

Tagging WAVE Sync videos

1. Sign in to your WAVE account.

2. Add a bookmark.

3. Tag your bookmark with “flex_ai”.

Importing WAVE Sync clips

1. Click WAVE Sync and enter your user ID and password.

2. Select your system from the dropdown menu.

3. Select the checkbox for each WAVE Sync Bookmark you would like to import.

Recommendations

FLEX AI: How do I annotate objects?

Summary:

This article describes how to move through a training video and mark objects. The goal is to take a video clip and pause at several points in the video and annotate objects (draw boxes around) you are teaching FLEX AI to detect.

Step By Step Guide:

Annotating objects

1. Pause the video on any frame that contains the object of interest.

2. Draw a detection box around every instance of the object. There can be multiple instances of an object and each instance should have its own detection box.

3. Click the Tighten button (or the keyboard shortcut T) to resize the detection boxes.
This means you can save time by roughly drawing the boxes and then tightening.

Step 1: Roughly draw a box around the object
Step 2: Click the Tighten button (or press T) to quickly get you close
There will be times that FLEX AI does not properly capture the true edges of the object, that’s why the application allows you to readjust the edges of the box. Step 3: Drag the edges/corners of a detection box to finely edit.

4. To remove a detection box, select the appropriate box and click the Delete key on your keyboard.

5. Click Save (or the keyboard shortcut S) to save the marked detection boxes.

6. Once you have drawn the necessary detection boxes, click the Train button. Your project will be unavailable during the training period which typically takes 15 to 30 minutes depending on the number of annotations.

NOTE: Since training is done in the cloud, you can work on any number of other projects
while a project is training.
.

NOTE: The blue detection boxes also appear in the This Frame’s Detections area after you
save. It is recommended that a minimum of 50 detection boxes be defined before your
initial object training is complete. An AI model can include detection boxes from
multiple video clips.

Keyboard shortcuts

You can save time and effort when navigating video, marking, tightening and saving annotations, by using the keyboard shortcuts below.

FLEX AI: How do I improve my object detection model?

Summary:

This article covers improving the AI Object Detection model of your uploaded videos. This process will result in more accurate detections, fewer false positives, and fewer false negatives.

Step By Step Guide:

To improve the AI Object Detection model:

1.Click the Improve button (towards the top right of the video player) after you have reviewed the latest model.

2.Select a video to start.
FLEX AI will suggest the top 10 frames crucial for highlighting your object(s) to enhance your object detection model. Markers represent each frame the application is asking you to revisit.

3.Draw a detection box around every instance of the object.
Remember to save your detection boxes.

4.Click the Object Not Present button (towards the bottom right of the video player) if the object of interest is not in the frame.

5.Use the arrows or the orange dots to advance to different/suggested frames.

6.Complete all 10 suggested frames and repeat for all videos to be included in the next training.

7.Click the Add More button to manually look through the video and add detection boxes, if the suggested frames are not enough (ex: different angles and perspectives are needed in the training set).

8.Click Train when you are ready.
The current limit for a (1) year license is to have a maximum of (100) total trainings or improvements.

NOTE: All 10 suggested frames must be completed per video for them to be included
in the training. Detection boxes on any video where all 10 frames are not marked
will be discarded and not included.

FLEX AI: How do I review and download my FLEX AI model?

Summary:

This article covers reviewing the AI Object Detection model of your uploaded videos.

Step By Step Guide:

To review your uploaded videos:

1.Click the Ready to View button to select your trained AI model results video.

2.Adjust the confidence level slider (towards the top right of the video player) to view the identified objects that meet your specified minimum confidence level.

The following model has been trained only once, so there is no option to compare.

3.After training the AI model more than once, click the Single/Compare Player toggle to change your view from side-by-side video player to single video player.

The following model has been improved, so both the previous (left) and current (right) can be compared. We can already notice the newer model is performing better.

For tips on improving detection accuracy, refer to the following article: How do I improve my object detection model in FLEX AI?.

4.Click the Download button (towards the top right of the video player) when you feel the model has been trained to your preferences. The model can then be uploaded to a camera.

5.Upload your newly trained model to your target camera.
Refer to the following article: How do I upload a FLEX AI model to a camera?

NOTE: Downloaded AI models can be deployed to a camera via Device Manager/Wise Detector.

FLEX AI: How do I upload a FLEX AI model to a camera?

Summary:

This article describes how, after training a FLEX AI model, you can download it, and then upload it to a compatible P-Series AI camera.

Note: For simplification, the term ‘model’ refers to a ‘custom object model’.

Requirements:

NOTE: A FLEX AI model cannot run concurrently with a Hanwha Vision AI Pack.
Any existing AI Pack must first be uninstalled from the camera.
However, a FLEX AI model can run in parallel with the WiseAI app.

Step By Step Guide:

To initially upload a Custom Detection Model:

1.Download the model from FLEX AI.

2.Launch Wise AI

3.Go to the Setup tab

4.Choose the Object.tar file you’ve downloaded from FLEX AI.

5.Receive the success message

6.You can now see the model within the list

Also from within the Object Detection from the menu.

You should also see FLEX AI Model below the other object detection options.

To upload a different model:

FLEX AI: Which cameras are compatible?

Summary:

This article lists the cameras onto which an object detection model created using FLEX AI can be uploaded.

Compatibility:

FLEX AI supports the camera models listed below. They are all P series AI cameras which incorporate the greatest processing power required to run the AI models.

<p>The post FLEX AI Setup and Use Guide first appeared on NVR IPCAMERA SECURITY.</p>

Smart Bird Feeder Camera,1080P HD Camera Auto Capture Bird Videos & Solar Panel, App Notify When Birds Detected, Free AI Identify Bird Species, Bird House with Built-in Microphone.

Download Bird Lover app

Download and install the Bird Lover App for either IOS or Android.

Login Bird Lover app

Once downloaded, the APP will prompt you to register your device. Enter your phone number or email address which one makes you feel comfortable and select the country you live in. You will receive the registration code. Input the registration code, then create a password.

Note

Indicator Description

Connect Bird Lover Bird Feeder Camera To Wifi

1. Turn on the Bird Lover Bird Feeder camera power and you will see the indicator light flashing quickly and hear a sound.

.

2. Open the Bird Lover App, click +, select your Bird Feeder Camera (you can choose one at random, the connection is the same), and then follow the instructions of the App.

3. Bird Lover Bird Feeder Camera only supports 2.4G wifi, please make sure your current wifi is 2.4G.
Enter your wifi password, make sure the wifi password and wifi are correct and click Next.

4. Scan the QR code with the Bird Feeder camera. You will hear a prompt sound after a successful scanning.

NOTE: The QR code needs to be aimed at the camera below

5. Wait for Bird Lover Bird Feeder Camera to connect to your wifi, about 60-120 seconds.

Detection settings

1. Turning on or off the “Motion Detection” at the Features interface.

2. Make sure there is an option to turn on notifications.

Click “ME” in the lower right corner, Click the settings button in the upper right corner,Click App Notification.

3. Click “Alarm” to turn on or off. You also can set schedule for “Do Not Disturb Schedule” at the same interface.

Identify live birds

1. Click “bird” icon

2. Click “Gallery”-Click “photo”-Click “bird” icon

Reset Bird Lover Bird Feeder Camera

Press and hold the reset button for 5 seconds to reset the camera.

Bird Lover APP INTERFACE INTRODUCTION

Install Bird Feeder Camera

1. Stick the sticker on the tree or wall and drill holes within the range marked on the sticker.

2. Insert the green plastic screw spacers into the hole.

3. Fix the bracket with long screws.

4. Install the bird feeder and align the three holes underneath.

5. Fix bird feeder with three short screws.

6. Install the perch with the two screws in the package.

7. The bird house can rotate left and right.

How to Charge Bird Lover Bird Feeder Camera?

Bird Lover Bird Feeder Camera FAQ and Troubleshooting

How to get it to connect to two different routers?

It cannot be connected to two different routers at the same time.If you want to change routers, you will need to reset the camera and reconnect your phone and camera. Please make sure that your phone and camera are both connected to the same Wi-Fi network before pairing.

How to reset Bird Lover Bird Feeder Camera?

Why The current network is in poor condition/The APP keeps going round in circles?

The network signal is weak if there are walls between the outlet, router and phone. This is because the network signal is absorbed or blocked by walls or large obstacles. It will help to have strong Wi-Fi with a Wi-Fi extender/booster.

How to charge Bird Feeder Camera?

A solar charging panel integrated into the roof can provide a constant source of power to support the smart bird camera. You can charge the battery of the Bird Box Camera via USB for continuous charging at night and on rainy days.

Why the Bird Lover Bird Feeder Camera battery is drain so fast?

It is low power consumption camera. Plus the solar panel power in charge, it can maintain the daily energy consumption in sunny day. If the battery drains too fast, you should check:

How to identify birds species?

Simply click on the “Identify” icon and the app will identify the bird species and provide a description of the bird. See the manual for details.

Why the recognition result is wrong?

The accuracy of the results depends on the angle and clarity of the bird images.

To ensure a correct result, please ensure that the image is clear enough. The identifying features (bird’s head, tail, wings or pattern on feathers) should not be obscured by obstructions.

The bird should be in the main position in the picture; try to capture the best moment to recognise the bird if the previous recognition accuracy rate is too low; if there are two or more bird species in a picture, the identified result will be the one in the main position.

How many account can connect this Bird Lover Bird Feeder Camera ?

Only one account can connect to Bird Lover Bird Feeder Camera, you can share it with other accounts through the sharing function.

Can I use the Bird Lover Bird Feeder Camera without a TF storage card?

It is not affected for daily use without TF storage card. Without storage card, it can receive notifications, watch in real time, take pictures and record videos (It will be stored in the APP Gallery );

Just can’t record.

Will this camera show video through the app if my phone is 5g?

Yes.

.

<p>The post How To SetUp Bird Lover Bird Feeder Camera first appeared on NVR IPCAMERA SECURITY.</p>

VOSKER V300 Ultimate Camera Setup and User Guide

HOW TO UPDATE YOUR V300 ULTIMATE CAMERA FIRMWARE

VOSKER V300 Ultimate
.

Latest firmware released: January 23, 2024

Installation instructions for PC :

Installation instructions for MAC :

How to Install your V300 Ultimate Camera

Before installation

Verify:

What you’ll need for installation

Choose between:

Recommended installation – Camera

Recommended installation – Universal Solar Power Bank

For more information on how to install your VOSKER camera to get the best picture quality, read the article “What Can I Do To Increase My Photo Quality?”.

Download:

› Quick Start Guide (PDF)

Troubleshooting steps:

If the Universal Solar Power Bank is discharged, charge it by plugging the DC power adapter in the 5 V IN port.

CAUTION:

WARNING: Failure to follow these safety instructions may result in fire, electric shock, damage, or other injuries. This power pack is not a toy. Keep away from children and operate outside.

.

HOW TO INSTALL YOUR V300 CAMERA

Before installing your camera, we recommend that you test the coverage of the location you will be placing your camera. Consider using a VOSKER security box to protect your V300 security camera against theft and breakage.

Here are some of the best practices for installing your VOSKER camera:

Note: Make sure to place the camera in an area that gets a good amount of sunlight during the day (enough to cover 50% of the solar panel). This will help maximize the battery life of your camera.

For more information on how to install your VOSKER camera to get the best picture quality, read the article “What Can I Do To Increase My Photo Quality?”.

.

HOW TO ACTIVATE MY V300 CAMERA?

Before activating your camera:

Note: A 24-hour charge of the battery unit is recommended before the first-time installation.

Activating your camera with VOSKER mobile app:

Activating your camera with the VOSKER web app:

Turning your camera on:

The V300 powers on and secures a strong signal.

Note: There may be a 20-120 seconds delay for the camera to make the first communication or transfer the first photo/video to the app.

EVERYTHING YOU NEED TO KNOW ABOUT V300 LIVE STREAMING

A strong cellular signal on both devices will ensure smooth live streaming.

The V300 series offers the amazing feature of live-streaming as a 40-minute add-on that can be shared between compatible devices over a 12-month period.

Want to test it out first? Upon activation, every V300 includes two minutes of live streaming during the free seven-day trial period.

How to start a live-streaming

What is the difference between live-streaming and 10-second Full HD video?

The live-streaming allows you to see what is happening live around your camera. It can last as long as you have live-streaming minutes in your account. It is great when you receive a notification, and you want to check if there are still some movements.

Your camera stores a 10-second Full HD video on the servers at every detection. You can request the video to understand better what happened during the detection. Simply click on a photo and press the button “Request Full HD video”.

What is the impact on the battery life?

The more you use those features, the more it takes a toll on the battery life.

This is especially true if the V300 doesn’t get a steady and strong signal. Just like your cell phone, the camera will work harder to connect to the cellular tower and communicate information.

If you see the battery life dropping, consider adding the Universal Solar Powerbank to sustain your camera from 6 to 12 months.

How to buy additional live-streaming minutes?

You can easily purchase a live-streaming add-on which will add 40 minutes shareable among all VOSKER streaming devices for the next 12 months.

Mobile app:

Web app:

Warning: you need a transmission plan (Base, Alerted or Elite) before buying the live-streaming add-on.

.

<p>The post VOSKER V300 Ultimate Camera Setup and User Guide first appeared on NVR IPCAMERA SECURITY.</p>