.

Production Introduction

The NVR series is a HD surveillance product that designed for security field. It uses an embedded operating system to ensure stable system performance. It adopts the standard H.265 video compression algorithm and a unique spatial-temporal filtering algorithm to achieve high-quality, low-bitrate synchronous audio and video and 24/7 video recording. With TCP/IP network technologies, it has powerful network data transmission and remote control capabilities.

The NVR can be used locally or online applied as a part of a safety surveillance network. With professional network video surveillance software, it fully demonstrates its strong networking and telecommunication capabilities.

This NVR can be applied to security measures in various fields and departments such as banking, telecommunications, electric power system, judiciary system, transportation, smart communities, factories, warehouses and water facilities.

.

Unboxing and Initial Setup

When you receive this product, please confirm that it matches the model you ordered and carefully inspect the device for any obvious damage. After opening the casing, check whether the data cable, power cable, and other connections inside the device are firmly connected to the main board.

Please protect the labels attached to the bottom or back panel, which is very important to our after-sales service work. When contacting our company for after-sales service, you will need to provide the model and serial number on the order label.

1.2What’s in the box

or

.

NVR  Power Supply  USB Mouse

.

.

.

.

Quick Start Guide

.

Ethernet Cable  HDMI Cable  Quick Start Guide

Note: Products and accessories vary by product models, please refer to the actual product.

➊  Antenna   

USB Backup

.

Network Port

.

HDMI Port

VGA Port Audio Port

USB Mouse Power Port

.

❷  Antenna

.

.

HDMI Port

LAN Port USB 2.0 Port Type-C

NOTE: The picture shown is for reference only. Actual appearance is subject to the model you purchased.

➊

USB Backup

4

Monitor

3

2

1

Route

.

.

.

.

.

.

.

.

.

.

❷

USB 2.0 Port

LAN Port

Battery Camera

3

1

2

4

ZOSI Wireless NVR Detail User Manual

Read More : How to set up Zosi POE NVR System

.

.

.

.

.

.

HDMI Port  Type-C

Ⓒ Connect the NVR to the Router with Ethernet Cable.

Ⓒ Connect the NVR to the Monitor with HDMI Cable or VGA Cable. (VGA Cable is not included)

Ⓒ Connect the USB Mouse to the USB2.0 Port.

Ⓐ Connect the NVR to the Power Supply.

Ⓒ The monitor will display live view of the camera.

NOTE: To ensure the device works properly, it is recommended to power on the NVR first for testing before a final installation.

Via Smartphone

Search “ZOSI” in App Store, or use a browser to scan the QR code below to download and install the App, and follow the on-screen instructions to complete the initial setup.

.

App video operation link

.

Via PC

Download: https://www.zositech.com/app/

.

Basic Operation

After connecting the power supply, the power indicator light will turn on, and the device

will start up. At this time, you will hear a “beep” from the buzzer. By default, the system is in multi-screen mode.

Mouse Use:

Left-click:

Double-click a single-channel to make it full screen, and double-click again to return to the multi-channel display.

.

Left-click

Right-click

After the device is powered on normally, you need to log in to the system before operating it. The system will provide corresponding functions according to the permissions of the logged-in user.

The default for the device is “admin” and the default password is blank. You can log in to the system directly the first time after powering on.

After entering the preview page, double-click the left mouse button to switch between single or multiple display. On each preview screen, the date, time, and channel name can be displayed, and each screen display the recording and alarm status of the monitoring channel.

.

.

Motion Detection Triggered

.

.

Recording

.

.

Human-Figure Detection Triggered

Face detection Triggered

.

.

Vehicle Detection Triggered

.

.

.

.

Quickly enter the playback page Quickly enter the backup page Quickly enter the device information page Quickly enter the device network page Quickly enter the current camera configuration page Quickly enter the recording schedule page.

In preview mode, click the right mouse button to bring up the quick menu, and click the right mouse button again to exit the quick menu.

Single: Select single channel for live viewing Multi: Select multi-channel for live viewing

Start Scan: Start Scan refers to the system automatically

displaying each live video in sequence according to

theorder of the devices in channel lists.

Colour: adjust the brightness, hue, saturation, and contrast of the channel.

E-Zoom: Zoomed in digitally up to 4X or 8X of single channel.

Audio: Set the audio settings for each channel to enable, disable, or mute audio, and adjust the volume. When

[Auto] is selected, the audio will be enabled automatically when switching to the full-screen display

Snap: Snap and save the live view images

PTZ: Control the rotation of the PTZ camera and set the automatic cruise/preset point cruise.

Stop Record: Stop /Start Recording

Time Playback: As described in 3.4.2 below Intelligent Detection: Set up Intelligent detection and Siren Light Alarm

IPC Channel Configuration: IPC channel configuration management,upgrade cameras, etc.

Main Menu: Ether the Setting Menu

.

Pause/Play Prev Frame  Next Frame

Mute  Backup  E-Zoom

Exit

.

.

.

Backup: Enter the backup page.

Rewind Fast Forward

Speed up Speed down

Fast Forward: Play video clips at speeds ranging from 1/16x to 16x. Rewind: Play video clips in reverse at speeds ranging from 1/16x to 16x. Speed down: Play the video from the previous 30 minutes.

Speed up: Play the video from the next 30 minutes.

The function takes effect when the pause button is pressed.

Prev Frame: Play video frame by frame. Next Frame: Rewind video frame by frame.

.

Main Menu

Set functional parameters of the device, including: Basic Configuration, Live Configuration, Recording Configuration, Recording Schedule, Alarm Configuration, Network Configuration, User Management, PTZ Configuration, Advanced Configuration.

Basic configuration contains 3 sub-menus: System, Date & Time, and DST

.

[System Type]: The name of the system displayed on the client [Model Number]: Used for controlling multiple NVRs with one remote control [Password Check]: Checking this option means that users must enter a username and password in the system settings and have the corresponding permissions to perform certain operations. [Show System Time]: Choose whether to display the time on the scene. [Max Online Users]: Set the number of network users who can access the device. [Video Output]: Users can select output resolutions 1024×768, 1280×1024, 1920×1080, 2560X1440，etc..

[Logout After (Minutes)]: The system automatically logs out after a set time of inactivity. [Startup Wizard]: Whether to display the wizard on startup.

.

Set the start and end times of daylight saving time through the week or date.

Live configuration contains 3 sub-menus: Live, Main Monitor, and Video Video Masking.

1.Live

.

.

.

.

.

.

.

[Camera Name] Click on the camera name, and a software keyboard will pop up. Users can modify the camera name as needed.

Click on the Shift key to switch input method. [Colour] Users can adjust the brightness, hue, saturation, and contrast of the channel.

Configure display window format for the patrol view

Users can mask certain areas in the scene, max 5 areas.

[Mask Setting] Enter the live view, hold down the left mouse button, drag the mouse to set the blocked area, click [Save] to save the setting.

Double-click the area that needs to be deleted, and the area will turn black. Right-click

to exit, and then click[Save] to delete the blocked area.

.

Recording configuration contains 4 sub-menus: Enable, Video Quality, Time Stamp , and Snap.

Enable/disable recording functions for a specific channel, or set all channels to default enable. All channels default to enabling circular recording.

.

Note：These functions are not optional [Resolution] The recording resolution for each channel [FPS] The number of frames per second transmitted by the camera image [Max Bitrate] Camera supports maximum transmission bitrate

[Camera Name] Select whether to display the camera name or not [Time Stamp] Select whether to display time on this channel or not [Position] Click this button and users can use the mouse to drag the camera name and timestamp to any position on the live screen.

Recording schedule contains 3 submenus: Schedule, Motion, PIR/intelligent.

.

[Apply Setting to]Apply the recording schedule of a certain channel to other channels or all channels.

[Add] Add a recording schedule for a certain day [Delete] Delete the selected schedule

.

[Enable] After selected, the Motion detection function of the corresponding channel is turned on, and it is enabled by default [Holding Time] Select the alarm delay time for the channel, which can be set to 5s, 10s, 20s, 30s, 60s, 120s, or Always on. [Push Time] Set the time interval for pushing alarm notification to the mobile App, which can be set to 1min, 2min, 3min, 5min, 8min, or 10min. [Trigger] After the camera detects an alarm, the enable function is triggered

[Buzzer] When selected, the buzzer will sound when an alarm triggered [Show Full Screen] When there is an alarm trigger, the alarm will pop up in fullscreen display

[To Alarm Out] Select to trigger the alarm output on a specified channel [Email] When an alarm is triggered, the system will send relevant information to the user’s designated email, such as the alarm event, snapshot, device name, device number, etc. [Snap] When an alarm is triggered, the system will automatically capture and save images of the selected channel [To Record] Select the channel to trigger recording

[Area] In this interface, users can drag the scroll bar to adjust the sensitivity value (1-8), the default value is 7, the smaller the value, the higher the sensitivity. Because the sensitivity is affected by factors such as color and time (day or night), users should adjust the value according to the actual situation.

.

Click or drag the mouse to select or erase the detection area.

[ALL] set the entire field of view as a s ensitive area

[Save]Click to save settings

[Clear] clear the current detection area  [Exit] exit the current setting

interface

The sensitivity index ranges from 1 to 8. The default sensitivity is 7. The lower the value, the more sensitive. The higher the value, the less sensitive.

Note: It is best not to have flags,trees or other objects that are easy to flutter in the wind in the grid for motion detection to avoid false alarms.

[Schedule]

The setting of the motion detection schedule is the same as that of the scheduled recording. Please refer to 4.2.4 [Recording Schedule]-[Schedule] for specific setup steps. This function controls the effective time of the motion detection feature. Note: The default schedule for motion detection is to Select All.

.

[Channel] Select the channel for setting. [Holding Time] Select the alarm delay time for the channel. Options: 5s, 10s, 20s, 30s, 60s, 120s, Always [Push Time] Set the time interval for alarm notifications to be sent to the App.

Options: 1min, 2min, 3min, 5min, 8min, 10min [Trigger] The setup method is the same as Motion detection. Please refer to 4.2.5 Alarm Configuration – Motion detection-[Trigger]. [Schedule] PIR detection schedule setting is the same as Motion Detection. For detailed instructions, please refer to 4.2.5 Alarm Configuration-Motion Detection-[Schedule].

This feature controls the effective time of PIR detection.

[Channel] Select the channel for setting. [Enable] Set to select the alarm type such as human detection, face detection, vehicle detection, etc.All selected by default [Holding Time] To select alarm delay time of the channel .Optional time: 5/10/20/30/ 60/120s always. [Push time] Select the channel APP alarm push time, optional 1/2/3/5/8/10 minutes. [Trigger] The setup process is the same as for Motion detection configuration. Please refer to 4.2.5 Alarm Configuration – Motion detection-[Trigger] [Area ] After entering the live screen, press and hold the left mouse button, drag the mouse to set the intelligent detection area, click [Save] to save the settings; double- click the set area again to delete the human figure detection area.

Note: The default is to set the whole region. [Schedule]The schedule settings for intelligent detection alarm are the same as motion detection. For detailed instructions, please refer to 4.2.5 motion detection-Schedule. This feature controls the effective time of intelligent detection

4.Siren-Light-Alarm This page includes camera detection settings, alarm type, night vision mode, volume adjustment, and more

.

[Enable] After selected, the vehicle detection function of the corresponding channel is turned on, and it is enabled by default After opening, the sound and light alarm function of each channel can be set. [Alarm level] can choose strong sound and light alarm, slight sound and light alarm, strong sound alarm, slight sound alarm, strong light alarm [Alarm type] can choose motion detection, intelligent alarm, motion detection and intelligent alarm [Night Vision Mode] Black and White Night Vision, Full Color Night Vision, Intelligent Night Vision;

[Volume] Adjust the current channel ‘s volume [Manual alarm] Set manual sound and light alarm [Waning Light] can turn on and off the LED warning light of the camera

When the video loss, the NVR triggers alarm actions.

.

[Buzzer] When an alarm occurs, the device emits two long beeps. [Show Full Screen] When an alarm is triggered, the system will show the current channel with the whole monitor [Email] When an alarm is triggered, the system sends the alarm event message to the user’s specified email address.

[Alarm Types] Including Disk Full, IP Conflict, Disconnect, Disk Shortage Alarm,

Disk lost

[Buzzer] When an alarm occurs, the device emits two long beeps.

[Email] When an alarm is triggered, the system sends relevant information such as the alarm event, snapshots, device name, and device ID to the user’s specified email address.

[Disk Shortage Alarm] When the remaining capacity of the hard disk reaches the set value, an alarm will be triggered.

.

Network Configuration contains 3 sub-menus: Network, Email, WIFI Network

.

[HTTP Port] 80 by default [Server Port] 5000 by default [Mobile Port] 5001 by default

[Obtain an IP Address Automatically] Enable automatic IP address acquisition [IP Address] Set the IP address of the device [Subnet Mask] Set the subnet mask of the device [Gateway] Set the default gateway of the device [Preferred DNS Server] This address is provided by your internet service provider (ISP). It must be filled in when using mobile monitoring.

[Alternate DNS Server] This address is provided by your internet service provider (ISP). [PPPOE] Enable this option to establish a network connection using PPPoE. The connected IP address can be checked in[Main Menu]- [Information]- [Network] [User Name] Enter ISP (provided by Internet Service Provider) [Password] The password set [Test] Test whether the input IP address or PPPoE information is valid

[SMTP Server] Mail server address, which can be an IP address or a domain name (if it is a domain name, ensure that DNS is correctly configured for proper resolution). For example: smtp.gmail.com [Port] Mail server port number, the default port is 465 [SSL Check] Enable SSL (Secure Socket Layer) protocol for secure login [Send Address] The email address of the mail server [Password] The password for the sender’s email address [Receive Address] When an alarm occurs, it will be sent to the set email address. Up to 3 recipient email addresses can be set [Test] Test the current email configuration to check if it is successful.

This page shows the AP information of NVR，To protect user privacy, we hide important information [wifi channel]You can choose the camera WiFi channel，optional WiFi channel 1、2、3、4、5、6、7、8、9、10、11、12、13、other [Area] optional Area:MKK、EU、FCC、OTHER

[Add] : Add a username and set the user’s permissions. Clicking on it will bring up the following interface:

.

User can configure PTZ settings

Click the [Setting] button, and the following window will pop up: The user can adjust the PTZ camera to a suitable position through the button on the tool bar, click [preset call], the preset point is set successfully, and a maximum of 4 can be set. [Start preset point cruise] If enabled, the camera rotates according to the user’s preset point position sequence. [Start automatic cruise] If enabled, the camera will rotate horizontally at a certain speed. [Humanoid Tracking] If enabled, the camera will automatically turn on human tracking.

Advanced Setup contains 2 sub-menus: Reset, System Maintenance

.

[Reset] Restore all settings to factory settings [System Maintenance] The video recorder defaults to restart automatically every week at 2:00 am on Monday. User can choose to restart Daily, Weekly, Never.

.

Select a channel and start playing [Search] Search the video files for the selected channel and time. Click the Play icon to start playback.

NOTE: Dates in the calendar marked with blue squares indicate recorded footage.

1.3.2Event Search

[Search] Search the video files for the selected channel and time. Choose the desired time, click Search and select the file, and double-click the mouse to start playback.

[Search] Search for images for the selected channel and time. [Save] Save the currently displayed image to a portable storage device. [Save All] Save all captured images to a portable storage device.

NOTE:

1.The system’s default storage capacity for images is 2000. If the number exceeds 2000, the system will automatically overwrite previously unlocked images.

2.Double-click an image to play back the video from the time when the image was captured.

1.4Backup

.

By configuring the settings, the video files in the device can be backed up to the external storage device.

NOTE: Before backing up files, make sure to install a storage device that can accommodate the backup files. [Search] Select the files to be backed up based on the time and channel.

[Backup]Select the file that you want to back up in the list and click Backup. The video recorder backs up the video file to the USB flash drive.

Information contains 6 sub-menus: System, Event List, Network, Online Users List and System Update

.

.

.

.

.

[Refresh] Re-detect recognizable hard drives. [Browse] View information of the selected hard drive, including capacity, remaining space, disk status, attributes, total number of pictures that can be stored, and number of pictures that have been saved. [Format]: Delete data in the selected hard drive, including locked files and pictures.

The current user logs out of the system. If the user wants to log in again, they can

click on the main menu icon and enter their username and password on the login interface to log back into the device.

.

5

FAQ

Q: No Video Output on the Monitor?

Q: Failed to Remotely Access the Camera via Mobile Phone or Computer?

Q：Does the system support motion detection and image capture?

.

6

Notification of Compliance

FCC Compliance Statement

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

Simplified EU Declaration of Conformity

ZOSI declares that the device is in compliance with the essential requirements and other relevant provisions if Directive 2014/53/EU.

Correct Disposal of this Product This marking indicates that this product cannot be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal and promote the sustainable reuse of material resources, please recycle it responsibly. To return your used device, please visit the Return and Collection System or contact the retailer from whom the product was purchased. They can take this product away for environmentally safe recycling.

<p>The post ZOSI Wireless NVR Detail User Manual first appeared on NVR IPCAMERA SECURITY.</p>

How To Upgrade Firmware on a QCAM NVR.

Any QCAM NVR should always be operating on the latest firmware version available.

If you are experiencing intermittent connectivity to the internet, general bugginess or difficulty using any feature, you must make sure there is no available firmware update which would indicate you are not on the latest version.

There are 2 ways to check for your NVR firmware version:
1. On the NVR’s built-in interface, from the Main Menu, navigate to System(in the Info row)->Version.

2. On the web interface, log in, then click the “i” icon in the top right corner and you will land on the Version page.

The NVR cannot be expected to work as advertised unless it is up to date.

Please always make sure you have the latest version before trying any other troubleshooting steps or contacting support.

There are 2 methods to update the firmware on your NVR: directly on the NVR or through the web interface.

Read Next : ,

1. TKH Security Firmware Software Guide
2. TIGERSECU NVR XVR Firmware Upgrading Instruction
3. UNV NVR Cloud Upgrading Guide

Method 1: DVR Interface

The safest way to upgrade the NVR is by doing it directly on the device.

First download the most recent firmware from http://www.amcrest.com/firmware-subscribe.

Now copy the firmware onto a flash drive.

Note: The flash drive must be formatted to FAT32 or exFAT. But do not worry, most flash drives are formatted to this by default.

Insert the flash drive into the USB port on the NVR and a window will appear.

Select the System Upgrade option. You may be required to login. Be sure to use an administrator account.

The System Upgrade window will now be shown. Click Start.

Select the firmware file that you downloaded and click Start. A progress bar will be shown at the bottom of the window. Once the upgrade has finished the NVR might restart on its own.

Note: Do not turn off the NVR during the upgrade process or it can damage the NVR and make it inoperable. 

Method 2: Web Interface

First download the most recent firmware from http://www.amcrest.com/firmware-subscribe

Next login to the NVR’s web interface. Click the setup gear icon in the top right. Then click System on the left panel, then Upgrade below it.

Click the Browse button and select the firmware file you downloaded.

Click the Upgrade button and the upgrade process will begin. A progress bar will appear showing you the progress of the upgrade. Once the upgrade has finished the NVR might Restart on its own.

Note: Do not turn off the NVR during the upgrade process or it can damage the NVR and make it inoperable.

After upgrading the firmware, it is a good idea to reinstall the plugins. If this is not done automatically, or if you have issues with the web interface, check out this article: Removing Old Plugins

Important Safeguards and Warnings

Important Safeguards and Warnings

1．Electrical Safety

All installation and operation should conform to your local electrical safety codes.

The product must be grounded to reduce the risk of electric shock.

We assume no liability or responsibility for any fires or electrical shock caused by improper handling or installation.

2．Transportation Security

Heavy stress, violent vibrations, and excess moisture should not occur during transportation, storage, and installation of the device.

3．Installation

Handle the device with care. Keep the device right side up.

Do not apply power to the NVR before completing installation.

Do not place objects on top of the NVR.

4．Repair Professionals

All the examination and repair work should be done by qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or user-attempted repair.

5．Environment

The NVR should be installed and kept in a cool, dry place away from direct sunlight, flammable materials, explosive substances, etc.

This product should be transported, stored, and used only in the specified environments as stated above.

<p>The post QCAM NVR Setup and User Guide first appeared on NVR IPCAMERA SECURITY.</p>

Production Introduction

1. Product overview

The series NVR is designed specially for security and defence field and is an outstanding surveillance product. It introduces embedded LINUX operating system which is very stable. It introduces standard H.265 mp video compressed format and unique temporal and spatial filtering algorithm which insures the high quality image and low bit rate synchronous audio and video surveillance. It introduces TCP/IP network technology which achieves the strong network data transmission capability and remote control capability. The series NVR can be used individually or online applied as a part of a safety surveillance network. With the professional network video surveillance software it achieves the strong network communication ability and telecommunication ability.

How to set up Zosi POE NVR System

Read Next :

• Zosi NVR Operation – Setup Menu Guide
• Zosi DVR/NVR Firmware Software Tools DL
• How to add an IP camera to a Zosi NVR

The series NVR can be applied in the bank, telecom, electric power system, judicial system, transportation, intelligent housing, factory, storehouse, water conservancy and so on.

Open-package check and cable connections

1. Open-package check

When you receive the product, please confirm whether it is consistent with the product model you ordered and check carefully whether there is any obvious damage of the product. After opening the casing, check whether the connection between the internal data wire, power wire, fan power wire and so on and the main board are firm .Please protect the labels afifxed to the floor or rear panel , which is very important to our aftersales service work. When you contact our company for after-sales service, we need you to provide the model and serial No. on the label.

1

1. Introduce the NVR

I® I® LAN Port^^ L^-USB2.0 Port

Power Port PoE Interface Audio Output^ L®_ HDMI Port

NOTE: To ensure the device works properly, it is recommended to power on the PoE NVR first for testing before a final installation.

1. Device connection

2

@ Connect the Cameras to the PoE NVR with 60ft(18.3m) Ethernet Cable.

@ Connect the PoE NVR to the Router with 3ft(1m) Ethernet Cable.

@ Connect the PoE NVR to the Monitor with VGA or HDMI Cable.

@ Connect the USB Mouse to the USB2.0 Port.

@ Connect the PoE NVR to the Power Outlet.

@ Turn on the power switch and enjoy live view.

@ The monitor will display live view of the camera.

NOTE: To ensure the device works properly, it is recommended to power on the PoE NVR first for testing before a final installation.

1. Access the System via Smartphone or PC

Smartphone

Search “ZOSI Smart” in the APP Store or use a browser to scan the QR code below, download and install the app and follow the instructions to register an account.

Zosi Smart

App (IOS/Android)

App video operation link

PC

Download path: Go to https://www.zositech.com/pages/app.

3

_L© Basic Operation

1. Turn on

Plug the power supply, the power indicator light will illuminate and the video recorder turns on, you will hear a beep at this time. I

After startup, the default setting of the ^{Left Button Right Button}

system is multiple-screen output mode and t I

video recording starting up automatically. ¹ ^B

Mouse Operation: JH

Left Button:

• Preview or Playback Interface: w W

Double-click a single channel to enter full I

screen and double-click again to exit full screen. \ 1

• Navigation Menu: Left click to select a menu option.

Right Button:

• Right click to bring up the main menu when the mouse is on the preview interface.
• Navigation Menu: Right click to exit the menu or return to previous menu option.

1. System login

When the DVR boots up, the user must login and the system provides the corresponding functions with the user purview.

The default user name of the factory equipment is admin, and the default password is blank. You can directly log in to the system when you log in to the system for the first time after starting up.

1. Preview

After entering the preview status , double-click the left mouse button to choose the switch between the windows. The system date, time and channel name are shown in each viewing window. The surveillance video and the alarm status are shown in each window.

4

1. Desktop shortcut menu

In preview mode you can right click mouse to get a desktop shortcut menu and right click mouse again to ESC the desktop shortcut menu.

• Single – Select single channel for live viewing
• Multi – Select multi-channel for live viewing
• PTZ: Control the rotation of PTZ camera
• Start Scan – Start/Stop Scan
• Colour – Adjust colour and image settings
• E-Zoom – E-Zoom the preview interface
• Audio – Adjust the camera volume
• Snap – Snap and save the live view images
• Start/stop record
• Playback – Search Video playback and quick playback
• Intelligent Alarm – Set up Human Detection and
  Siren-Light Alarm
• IPC Channel Configuration – IPC channel
  configuration management
• Main Menu – Enter the Main Menu

1. Single Screen

Select a channel for single-screen viewing.

5

1. Multi Screen

Select the corresponding different multi-screen mode to watch.

1. PTZ

Control the rotation of the PTZ camera and set the automatic cruise/preset point cruise.

1. Start Scan

Start Scan means the system will show each live picture in order automatically according to the order of the video devices in the channel grouping. Only when the user selects the channel grouping under the display mode[main menu]>[configuration management]>[live], and it can not show all channels completely under the current preview, this button is available.

6

1. Colour

Set image parameters for all channels. The image parameters include: brightness, contrast, saturation and hue.

Channel

Default

Save

1. E -Zoom

E-Zoom for big picture of single channel.

1. Audio

Set startup, turn-off and silent mode of audio for the channel, and adjust the volume ..After select (automatic), it will start up audio of the big picture channel automatically.

7

1. Snap

Snap a screenshot of the current channel.

1. Start/stop record

After clicking start recording, the system will start full-time recording; after clicking stop recording, the system will stop full-time recording.

3.5.0 Playback

Right click the mouse – Playback – Video Playback/Quick Playback, Video Playback: Playback the video clips via time search or event search. Quick Playback: Quick playback of the first 30 minutes of video.

8

Fast Rewind

Play/Pause For_ward Multi-screen display

T

Previous Record Next Record

Previous Video: Play the previous video.

Next Video: Play the next video.

Fast forward: You can play the video clips at 1/4 time speed to 16 times speed.

Rewind: You can rewind the video clips at 1 time speed, 8 times speed, 16 times speed, and 32 times speed.

Screen Modes: Single Channel Playback/Multi-channel Playback. Channels without video playback will show a black screen.

1. Intelligent Alarm

Set up Intelligent Alarm and Siren-Light Alarm.

9

1. IPC Channel Configuration

View camera version information, add cameras, upgrade cameras, etc.

1. Main Menu

Enter the system main menu interface.

10

Q Main Menu

1. Main menu navigation

11

1. Configuration Management

Set every function parameters for the device, including: basic configuration, live configuration, recording configuration, recording plan, alarm configuration, network configuration, user management, PTZ configuration, advanced configuration.

12

1. Basic Configuration

Basic configuration includes three sub menus: system, date and time, daylight saving time.

1. The system

13

2. Date & Time

In this interface, set the date format, time format, time zone; you can also adjust the system time manually.

Note: the default time zone of the system is GMT.

You can select [Time Synchronization] to correct time. Network time server can be set.

1. DST(Day Light Saving)

Set the start and end time of daylight saving time by week or date.

14

1. Live Configuration

Live configuration includes three submenu: Live, Main Monitor, Video Blind.

1. Live

1. Main Monitor

15

3. Video Blind

Users can cover up some areas of the live picture, maximum of five areas per channel. [Setting] After entering the live picture , press and hold the left mouse button, drag the mouse to set the blocked area , then click [apply]to save the settings; Double-click on the area you want to delete, later changed into a black area, right-click, Exit. then click [apply] can delete the blocked area.

1. Recording Configuration

Record configuration includes six submenus: Enable,Record Bitrate,Stamp,Recycle Record,Snap.

1. Enable

16

1. Record Bitrate

Check the main stream and sub stream information. [Resolution] Display/select camera resolution. [Code rate] Show camera code rate.

1. Stamp

17

1. Recycle Record

After selecting this item , When the hard disk is full, it will automatically cover the earliest files and continue recording ; Otherwise, it will automatically stop recording and prompt “The remaining space is insufficient” on the screen.

Record O

1. Snap

View screenshot information.

18

1. Schedule

Schedule includes three submenus: timing recording, motion alarm recording, and intelligent recording.

1. Timing Recording

Select the channel: Double click the left mouse button, edit the week plan, as shown in the picture.

19

1. Motion Alarm Recording

The setting method is the same to the timing recording setting, please refer to the timing recording settings.

Note: The default Schedule for Motion alarm is all selected.

1. Intelligent alarm

The setting method is the same to the timing recording setting, please refer to the timing recording settings.

Note: The default Schedule for intelligent alarm is all selected.

20

1. Alarm Configuration

Alarm configuration includes five submenus: Motion detection, Video loss, Other alarm,Intelligent alarm,Siren-Light alarm.

1. Motion Detection

Motion detection includes two submenus: motion detection and schedule.

1-1. Motion Detection

By analyzing the video image, when the system detects a mobile signal which reaches a preset sensitivity, motion detection alarm and the linkage function are initiated.

21

1-2. Recording Schedule

The setting of Motion Detection Schedule is the same to that of Timing Recording, For the detailed steps please refer to 4.2.4 – [Recording Schedule] [Timing Recording]. Note: The default schedule of motion detection is all selected.

2. Video Loss

The setting of video loss alarm processing is the same to that of motion detection alarm processing.

22

1. Other Alarm

1. Intelligent alarm

23

1. Siren-Light Alarm

Siren-Light Alarm

All

|D |O Both (Loud) ^w | Motion ^w | |

Default Exit

After opening, the sound and light alarm function of each channel can be set.

24

1. Network Configuration

Network configuration includes two submenus: Network, Email.

6-1 Network

25

6-2 Email

1. User Management

26

The default administrator name is admin, there is no password set.

Note: The length of the user name and password is no more than 32 characters. [Add] Add a user name and set the user’s permissions.

27

1. PTZ

1.[Preset] Click the [Setting] button, and the following window will pop up:

The user can adjust the PTZ to a suitable position through the button on the tool bar, click [Save], the preset point is set successfully, and a maximum of 4 can be set.

1. Advanced Configuration

Advanced setting includes three submenus: Reset, Import/Export,system maintenance.

28

1. Through ‘’Import/Export”,you can export the parameters to other devices directly.

There is no need to reconfigure other devices.

1. The system language can be changed by import language files.

1. Data Retrieval

Mainly includes Time Search, Event Search, and Image.

1. Time Search

Select the channel to play

Start playing

Note: The highlighted date in the calendar indicates there is video file on that day .

29

1. Event Search

1. Image

30

Note: 1. The default number of storage image is 2000. If it is more than 2000, the system will automatically overwrite the previously unlocked images.

2. Double-click the image, you can playback the video from the time when the image was captured.

1. Backup

By setting, you can backup the video file to the external storage device

Note: You need to install the storage device capable of accommodating the storage files before backuping the files.

31

Disk cleanup: to delete all files in the external storage device.

1. View Information

Including five submenus: system information, event information, system log, network status, and online users and other relevant information.

32

1. System

To display the basic information about this device, including hardware information, software version number, release date, and phone port number .

1. Event list

Users can select the event information of motion detection alarm, sensor alarm, video loss alarm and so on which users need to inquire about according to time and channel.

33

1. Log list

Users can search the operation information of the login user based on time and the operation type. After formatting the hard disk, the information will be cleared.

1. Network

Users can view the related parameters of the network settings.

34

1. Online Users list

See the network user information connecting the local NVR.

1. Disk Management

35

1. Log User off

The current user logs out of the system. If the user wants to log in again, click the main menu icon and enter the user name and password on the login interface to log in to the device again.

1. Manual Maintenance

If manual maintenance is confirmed, the system will automatically restart.

1. Upgrade Maintenance

36

<p>The post How to set up Zosi POE NVR System first appeared on NVR IPCAMERA SECURITY.</p>

1. Descriptions of functions
   1. Basic function description

This section describes the main functions of the high speed and the infrared dome cameras and the general principles of their implementation, nospecific operation methods involved. The specific operation method of different system platforms varies. Generally, the operation manual of the system manufacturer shall prevail. In some cases, there will be some special requirements and operation methods. Please contact the dealer for necessary information.

• Automatic matching technology of PTZ / rotation rate

The dome camera can automatically adjust the horizontal and vertical rotation rate of the PTZ according to the multiple of variation, which makes the manual operation easier.

• Set up and call preset position
• The preset function is that the dome camera can store the horizontal angle, tilt angle, camera lens focal length and other position parameters of the PTZ in the current state into the memory. These parameters can be called quickly when necessary and the PTZ and camera can be adjusted to this position. The operator can easily and quickly set or call the preset position by controlling the keyboard or equipment.
• Automatically scanning

Tiandy PTZ Cameras installation guide

Read Next :

1. Topsee IPCAM NVR Firmware DL
2. How to set PTZ control? UNV Device
3. Safire NVR Setup Guide

The operator can set the left boundary positon and right boundary position in advance by controlling the keyboard or equipment conveniently and quickly to achieve the automatic reciprocating scanning of the camera between the left and right boundary at the set speed level. This dome camera can set 8 scanning paths.

• Automatically scruising

The dome camera can program some preset positions into the automatically scrusing queue in required order through pre-programming. The operator can easily and quickly control the keyboard or equipment to allow the dome camera automatically scan in the specified time interval according to the preset position sequence. Each cruise track can store 32 preset positons.

• Pattern path (pattern scanning)

The dome camera can record the running track for 180 seconds continuously. After the pattern path function is started, the dome camera can scan and monitor as the recorded running track automatically.

• Watch position function

The dome camera can be set to automatically perform the set standby action after reaching the standby time: preset position, cruising, scanning, pattern path. The standby time can be set.

• Self recovery function after power off

The running state of the dome camera can be restored after the power is cut off and recovered to prevent the trouble of re-operating the dome camera caused by the unexpected power off effectively.

1. WEB client
   1. Operating Environment

It is recommended to run under the operating system environment of Win7 and above. In order to better operate and use the system, and fully reflect the performance and effects, please ensure that the following items are set or installed correctly after the system is successfully installed:

1. The display resolution is set to 1920 x 1080 or higher, and the color is set to enhanced color (32-bit), please refer to Windows help document or online help for how to set the resolution and color of monitor.
2. Make sure that the font required for this system-Song font is installed in the Windows operating system. If the interface of this system is displayed abnormally, the fonts required by this system may not be installed, or the required fonts have been damaged, and fonts need to be reinstalled.
   1. Instructions for embedded Web server

You need to download controls before using this series of network video products for the first time.

Note: Use the IE browser of Windows operating system, to ensure that the version is 8.0 or above. Except for Firefox and Google browsers, please do not use other third-party browsers and any IE browser shell programs such as Maxthon, Window of the World. We do not guarantee that you can log in normally with such software.

• 1. Login Device

The default IP address of the device is: 192.168.1.2. Please set the IP address of the computer and the IP address of the device in the same network segment: for example, set the IP address of the computer to 192.168.1.3 to access the device through IE browser. Open the IE browser, input the IP address of the network video device in the address bar, and click “go” to log in to the device. If it is the first time to use, the following interface will appear.

• • 1. Equipment activation

Fig.5.3.1.1 Equipment activation interface

Some devices need to be activated before IE interface is to be used . Set the login password in the activating device window and click OK to enter the IE login interface.

X

Activation succeeded, please log in again.

Fig.5.3.1.2 Prompt box for activating device

• • 1. IE login interface

Fig.5.3.2.1 IE login interface

Enter the correct user name and password in the login window, and click “Login” to enter the preview interface later.

Description:

1. If the equipment port number is modified, you need to enter the correct port number, and the default port number is 3000.
2. If the device supports activation, the password is the one set at the time of activation.
3. If the device does not support activation, the password is 1111.

The video preview serial interface will prompt the link to download the video plug-in as Fig.5.3.2.2. Click the link to download and install the plug-in. The IE interface needs to be closed during installation.

Please click to download the plugin, if installed already, pleasejust press F5 to refresh it (no need install again). Please close the browser during installing.

Fig.5.3.2.2 Download the video plug-in

After the video plug-in is installed successfully, enter the device IP again and log in the correct account password to enter the preview interface.

Fig.5.3.2.3 preview interface of video

After you log in to the system, the prompt box of “change password” will appear in the lower right corner of the desktop. Please click the text in the box, link to the user management interface, select the user, and click “edit”, as shown in the figure below.

Note: In order to ensure the security of your information, please be sure to change the initial password!

Fig. 5.3.2.4 Change password prompt box (supported by some models)

Equipment activation

User Name

Password

Password Strength

Please generate 8-15 digits password with two or more combinations of numbers, lowercase, capital letter and special characterfspedal characters cannot be quotes, colons, semicolons, # symbols, spaces, and backslashes).

Password Confirm

Optional (For Password Reset)

Fig. 5.3.2.5 Change the password

• 1. Audios and videos preview

After successful login, the system will display the [Live View] interface by default. In other interfaces, users can return to the video preview interface by clicking the [Live View] button at the top of the interface.

This interface mainly control basically the front-end equipment, such as the pan tilt, lens, wiper and so on.

• • 1. Button of video preview interface

Icon Description

Click “1st Stream”; the video window will display the primary code stream, and

1st Stream

the primary code stream will be displayed by default.

Click “2nd Stream”; the video window will display secondary code stream after

2nd Stream

selection.

Click “3rd Stream”; the video window will display third code stream after

3rd Stream

selection. (supported by some models)

Click “Fixed Ratio”; the video will be displayed at a fixed scale.

|< *| i Click “Fit Window”; the video will automatically adapt to the computer resolution

display.

QR code button. QR code will appear after clicking it. Users can scan the QR code

according to the type of mobile phone and download the mobile client. A third QR code will appear after the equipment is connected to the public network, and you can add the equipment by scanning on the mobile client. (Supported by some models)

Local manual snapshot control button, click enable to snapshot and save the preview picture locally, the storage path of the snapshot file can be modified by itself, the modification page: configuration system settings local settings preview snapshot save path.

Local manual recording control button, click enable, start local recording after enabling, the storage path of recording file can be modified by itself, modification page: configuration – system settings – local settings – saving path of recording file.

Voice intercom switch. When enabled, it can transmit local audio to the front-end equipment through the network for output.

Audio preview volume adjustment button, the local output volume can be adjusted by adjusting the slider position.

Electronic zoom button. After enabling this function, click the left mouse button to draw the area to be enlarged, and then you can zoom in and view the area. (Supported by some models)

Displays the frame rate button. After clicking, the preview interface displays the frame rate information of the current video. Click again to cancel the display of frame rate information. (supported by some models)

Full screen button. Realize full screen preview video, double click left mouse button or press the [Esc] key of keyboard to exit full screen preview video status

Caution

(1) All icons are valid when pressed.

(2) When there is no video in the interface, the audio preview is invalid.

1. Talk can only be conducted with one user at the same time, and it is recommended to turn off the intercom in time after completing the talk, so that

others can use it.

(4)

Click and

the arrow or on the right side of the video window to display / hide

the control interface.

( 5 ) Some models support “target information” to display the target and information identified by the intelligent algorithm. You can click “Zoom” / “target information” to switch the interface.

(6) Double click the left mouse button in the preview window to display the full screen. The dome camera can be controlled by keyboard: W“t”, S“_v”- A“<”- D“>”, I“zoom in”, K“zoom out”, J “focus near”, l “focus far”.

• • 1. PTZ control

The functions supported by different models are different, please refer to the actual interface.

Description

Icon

8 direction keys,press the corresponding direction key to control the pan tilt to rotate in the corresponding direction; the center button is the scan shortcut key, press center button can invoke scan 1.

The slider can adjust the rotation speed of the device.

The closer the “-” end is, the slower the speed is, and

the closer the “+” end is, the faster the speed is.

Zoom control button, press “-” control device to perform zoom operation, the field angle becomes larger and the scenery becomes smaller; press “+”

operation. In order to prolong the service life of the wiper, the wiper is equipped with low temperature protection measures, and the function of closing when the ambient temperature is lower than 0 °C.

Alarm removal button. Alarm can be removed after pressing the button. (Supported by some models)

Flip: control the video image to flip 180 °.

Snap button: press the button to turn on the front end interception function.

Front-end intercom button. Press the button to turn on the front-end intercom function.

Area exposure button: when there’s a large light difference of the monitoring scene, the area to be adjusted can be selected through the area exposure function to make moderate light of the key monitoring area.

Area focus button: when there’s a deep and large scale scene area of the monitoring scene, you can select the part of the scene that needs to be focused clearly through the area focus function.

Click the one-key watch button to automatically set the current scene to the watch preset (default preset 1), and turn on the watch function at the same time. If you want to stop the one-key watch function, please cancel the standby action in the dome camera setting-basic setting.

3D positioning button, click the mouse to control, adjust the scene to be monitored to the video center. Specific operation as follows:

1 , Click the left key on the required monitoring point in the monitoring video screen, and move the corresponding point to the video center;

1. Press and hold the left key to the bottom right to pull down a rectangular area, then the center of the corresponding delimited area will be moved to the center of the video and zoomed in;
2. Press and hold the left key to the top left to pull out a rectangular area, then move the center of the corresponding delimited area to the center of the video and zoom out.

Laser alarm button, click once enabling, after clicking, the laser is turned on, click again, the laser is turned off. The laser working temperature is – 15 °C – 45 °C, the longest lasting time is 300 seconds, and it will beautomatically turned off if it exceeds 300 seconds.

Strong light warning button, click enable, the strong light will turn on after enabling, and then click again, the strong light will turn off. (supported by some models)

Sound warning button. Click “Enable”, and play the alert tone after enabling. (Supported by some models)

Manual tracking button, click once enabling, and then click the target manually to track the target.

• • 1. Preset

After logging in the preset position number, you can select the operation of preset position, including set-up, call and delete.

Preset

Q, Preset NO

Fig. 5.4.3.1 Preset interface

The function of the presetting bit is that the camera can store the location parameters of the PTZ under the current status such as the level angle, angle of inclination and the lens focal length of the camera into the storage and the PTZ as well as the camera can be adjusted to this position through calling the these parameters if necessary.

Click the button’ ’ ’ to display preset function setting interface.

Preset number can be fill in the blank and use the’ ’ button to find the target preset number to config (‘ –^ ’)or call(‘ ’).Call functions are only available for existed presets.

• • 1. VCA Action

Click the button ^T Icon display the operation interface of the intelligent action. The interface includes One-key watching, auto cruise, auto scan, pattern and intelligent scene.

Fig.5.4.4.1 VCA Action

• • 1. Image

Click the button ^T Icon display parameter adjustment interface,the interface can

be adjusted by the following.

Fig.5.4.5.1 Image setting interface

Icon

Description

Day

Outdoor

Night

Outdoor

HD effect adjustment, adjust the daytime image effect.

The effect is divided into:

HD effect adjustment, adjust night image effect.

The effect is divided into:: Outdoor, Indoor, WDR, Motion, Bright, Colorful, customized.etc.

Defog function button. Click the button to turn on the defog function.(Some models support this function).

Button for HLC function. Click the button to turn on HLC.(Some models support this function).

Button for WDR function. Click the button to turn on WDR function.(Some models support this function).

• • 1. Quick Scene

display Scene application template interface.You can

Click the button ^T to

modify the parameter as follows:

• 1. Playback

Click [playback] to enter the [playback] interface.

Fig.5.5 playback

5.5.1 Refer to the front-end video file

In the playback interface, the user can view the video files of the specified date,

and can also snapshot and clip the video. See the following table for basic operation:

Icon

Descriotion

Slow forward button. The speed is 1/2 X, 1/4 X, 1/6 X and 1/8 X.

Play / pause button. Click to start/stop playing video file. Double speed playback will be canceled if necessary.

“Stop Playing” button. You can stop playing the current file by clicking it.

Fast forward button. The speed is 2 X, 4 X, 6 X and 8 X.

Stepping button can playback the video in a single frame.

Browse button, select the video file to play.

Playback snapshot button, saved by default in

C:\Users\john\NetVideoBrowser\CapturePics\o

Playback clip button: Click to start the clip, and click again to finish the clip. The default saving location is C: \ users \ John \ netvideobrowser \ snapshotpictures \.

Clip Management: you can view the type of video clip, video clip progress, current status and other information.

Volume adjustment button, the local output volume can be adjusted by adjusting the slider position.

Download Management: query or download videos and pictures.

Full screen play button: in full screen mode, double-click the mouse again at any position to exit from full screen mode.

4 A January – 2020- ►

Sun Mon Tue Wed Thu Fri

29 30 31 | 1 | 2 3

5 6 7 8 9 10

12 13 14 15 16 17

a date in the calendar, double-click the date, and find the

file according to the query criteria.

19 20 21 22 23 24

26 27 28 29 30 31

volume adjustment and mute

Stream

s_?–₅₃ – Choose the type of stream

In the time axis mode, users can drag on the time axis to select and view the video files of the corresponding time. After selecting the time point, click the play button <L./to play. The time axis can be narrowed or enlarged by click I I.

In file mode, users can operate according to file type, video recording type, and whether to query remotely. The specific functions of buttons in file mode are as follows:

Description

Icon

Set the type of file to be queried, such as [Record], [Picture], etc.

Select the type of video file to be queried. (Supported by some

RecType

Start Time

2d

models)

2020-04-01 00:00:00 ®

Select the start time of the video query

Stop Time

2020-04-01 23:59:59 g

Select the end of the recording query

Start downlo…

Start downloading selected video files

Stop Downlo…

Stop the selected video file being downloaded.

Back

Return to the playback interface.

Jump To [

Jump to the specified page.

Search

Query: Click to query the corresponding video information.

Jump to the first page of query results.

Go to the previous page of the current page.

Go to the next page of the current page.

Jump to the last page of query results.

Lock: the file can be locked and unlocked. When the disk is full and files need to be deleted, the locked files will not be deleted.

• 1. Log

Click [Log] to enter the [Log] interface.

Fig.5.6 Log Interface

Log interface operation instructions

1. Select the channel number to query from the [Channel No.] drop-down list.
2. Select the type of log you want to query from the [Log Type] drop-down list.
3. Select the start date in the [Start Time] drop-down list, and enter the time in

the edit box at the back.

1. Select the end date in the [End Time] drop-down list, and enter the time in

the edit box next to it.

1. Click the [Query] button to query the logs within the specified time range.
2. When there are many logs, you can use [First Page], [Pre Page], [Next Page],