Tapo was created to engage in the small intelligent appliances market, to help people adopt a new smart home lifestyle at an affordable cost. That’s why we insist on Smart, Easy, Secure.

.

What should I do if I fail to configure the Tapo Smart Plug?

The Tapo app will guide you step by step during the initial configuration, but you may not be able to get through all the steps due to some interference. This FAQ will tell you what to do if you have trouble getting through a certain step.

Case 1

The phone is looking for the smart device via Bluetooth or its default 2.4GHz WiFi, if you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

Tapo Smart Camera FAQ v1

Case 2

If you are unable to find your home Wi-Fi network, please refer to the following suggestions.

Troubleshooting tips:

1. The signal strength of your home Wi-Fi network is a bit weak, move the smart device closer to your router for a try.

2. Ensure your home Wi-Fi network is a 2.4GHz Wi-Fi network, the Tapo device does not support a 5GHz Wi-Fi connection.

3. If it doesn’t display the Wi-Fi name of the router automatically, please click on “RECAN” at the upper right corner to refresh the Wi-Fi list.

4. If the router’s SSID is hidden, please choose “Other” to input SSID and password manually.

5. Please change the wireless channel of the 2.4G Wi-Fi network to 1, 6 or 11.

6. Reset the device as per QIG/UG and go through the process again.

Case 3

If you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

1. Ensure you have selected the correct home Wi-Fi network and have entered the correct wireless password. If the Wi-Fi network or password is incorrect, click on “Choose a Network” and select the Wi-Fi network again.

2. Make sure your smart device is within the Wi-Fi range of your router.

3. Turn your phone’s or tablet’s Bluetooth off and back on.

4. If the problem persists, try to reset the smart device as per UG/QIG, and then set it up again.

5. Check if there is a firewall on your router. If yes, please turn it off.

6. Change the wireless security type of the 2.4G network to WPA2.

7. Try to connect the Tapo plug to the hotspot of your cell phone or another wifi network. If it works, please upgrade the firmware for the plug, then reset and reconnect it to your router.

.

What features does Tapo smart plug and Tapo smart switch support?

Currently the Tapo plug and switch supports the following features:

.

How to view Tapo camera on PC/NAS/NVR through RTSP/Onvif Protocol

The Tapo camera supports the RTSP and Onvif protocol, so it can work with third-party NVR or NAS devices that also support the RTSP/Onvif protocol. If a user wants to view the live stream of the camera with a third-party app like VLC Player, iSpy, here is the method for him.

Notes:

1. The username/password is the camera account that you created via the Tapo app. If you haven’t created the username and password, please follow the instruction of Step 1 in this article.

2. The IP address is the camera’s IP address assigned by your host router. You can find it on your host router’s DHCP list or in the Tapo app (Go to the Device Settings page of the camera and tap Device Info to see its IP).

3. If you want to view the live stream of the Tapo camera with a third-party app remotely, you will need to open port 554 for the camera on your host router first. Please enable the TCP forwarding for port 554.

4. You could use ONVIF standards to add the Tapo camera with its username/password and IP address. Please see the example of iSpy in Case 2 to know how to use onvif protocal to control the camera.

5. For Tapo C310, the resolution of the stream1 is determined by the video quality set on the Tapo APP.

If you need to watch the 3MP HD Video via RTSP, please change the video quality to Best Quality on the Tapo APP and use: rtsp://IP Address/stream1

6. If the Camera is inserted microSD card and subscribed Tapo Care, its RTSP stream will fail. You need to remove microSD card or cancel Tapo Care to get its RTSP stream.

7. If you find that there’s no or very little sound when using RTSP/Onvif to watch live stream, please adjust the camera microphone on Tapo APP.

Apart from the Tapo app, Tapo cameras can work with other third-party software to use and manage your Tapo camera.

Note: Before you start, make sure the computer/NAS/NVR and your camera are connecting to the same network or can visit the public IP and port of your camera.

Step 1: Create a camera account in the Tapo app

1. On the Home page, tap on your camera model card to go to the camera Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Advanced Settings, then select Camera Account to create an account (username and password) for camera login on other portals.

You will see a prompt like below (About Camera Account), please read it and tap Understand and Agree to Use, then you can create an account for the camera.

Note: The username and password should contain 6 to 32 characters.

Step 2: Add your Tapo camera on iSpy (Example of Onvif protocol connection)

1. Run the iSpy software on your computer.

2. Click Add on the top left menu and select ONVIF Camera.

3. Enter the Username and Password that you set for your camera on the pop-up window, select Network Address, and click Next. You can customize other parameters if needed.

4. Choose the video resolution and click OK.

5. Customize the camera settings as needed, including Microphone, Talk, Motion Detection, Alerts, Recording, Images, Scheduling, and Storage. You can also change all the settings later. Click Finish to complete adding your camera to iSpy.

6. After adding your Tapo camera to iSpy, you can monitor and manage it using the app. View the live, customize motion detection, check the recordings when motion detected, set recording schedules, record videos and more.

Step 3: Watch your Tapo camera on VLC (Example of RTSP protocol connection)

1.Open the VLC software, select Media > Open Network Stream

2.Fill in the URL of the Tapo camera

The URL of the RTSP live stream for the Tapo cameras will be:

For high quality stream1: rtsp://IP Address/stream1

For low quality stream2: rtsp:// IP Address/stream2

In some software, the URL need to add the port to access live stream, the default port is 554:

For high quality stream1: rtsp://IP Address:554/stream1

For low quality stream2: rtsp:// IP Address:554/stream2

If you fail to stream the Tapo camera via the RTSP/ONVIF protocol, you may refer to the article for the troubleshooting:

https://community.tp-link.com/en/smart-home/forum/topic/652710

To get to know more details of each function and configuration, please go to Download Center to download the manual of your product.

.

How to factory reset the Tapo or Kasa smart plug

.

To restore a Tapo or Kasa smart plug to its factory default settings and re-enable the setup mode, please press and hold the power button for 10 seconds.

The LED status for a factory reset varies by model:

After a completing the reset, you can then connect and configure the device in the Tapo App.

How to avoid noise when monitoring the sound from Tapo camera

Tapo cameras are capable of not only monitoring video stream from the camera, but also monitoring sound collected by the built-in microphone on the cameras. You can turn on/off the sound feature like the monitor screen as below. But to increase or decrease the volume, you need to press the volume button on your phone.

Why is there noise?

Noise is a physical phenomenon and it’s actually inevitable. Basically, the IP cameras including other brands’ have background noise more or less. And those cameras which seem to generate less noise probably have worse sound collecting performance. Tapo cameras are designed with a sensible sound collector which might take some noise in your monitor. Even though it is inevitable at present, we are still trying our best to make improvement and searching for better solutions.

How to reduce the noise?

1.     Please keep your mobile device away from the camera as much as possible. The Tapo camera is designed for remote access and monitoring via cloud service, local usage in close range may cause interference and noise between your mobile device and the camera.

2.    Please reduce the output volume below 50% since a louder volume may enlarge noise decibel. The value between 40%-50% is suggested with not only good sound quality but also minimum noise decibel. As long keep focus on our cloud camera you will find our progress on new models.

Your understanding is highly appreciated!

How to edit Home and Away Mode for Tapo&Kasa Cameras on the Tapo app

.

The Away mode and the Home mode are two different sets of Detection, Alarm, and Notification settings for Tapo&Kasa cameras. You can tap the button on the Tapo app>Cameras tab to quickly apply the preset settings to the cameras when you are home or away.

Note:

Here we take the Home Mode as an example.

For Tapo Cameras:

1. Open Tapo APP, find the Cameras tab at the bottom, and locate the Detection Mode section.

You can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three-dots option.

2. Click on Add Devices if you want to add more cameras to the Home mode.

Click on the Edit icon at the top right corner if you want to delete cameras from the Home mode.

3. Select the camera you want to edit the mode settings. Here we take Tapo C200 as an example, and you can change the Privacy mode, Detection, Alarm, and Notification settings of the camera.

Take the Motion Detection feature as an example. You can click on Motion Detection to turn it on or off, change the Motion Sensitivity, and set the Activity Zones on the Motion Detection page.

And you can also click on Detection>Person Detection or Baby Crying Detection to turn them on or off, and tap Alarm and Notifications to configure the related settings.

4. Click on the Back icon at the top left corner of the Tapo C200 page if you have changed the configurations, and click on other cameras if you want to change their configurations.

After completely presetting the Home or Away Mode, you can tap the Home mode or Away mode card on the Tapo app>Cameras tab to switch your cameras’ settings quickly.

For Kasa Cameras:

Here we take KC115 as an example.

1. Open the Tapo app, find the Cameras tab at the bottom and you can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three dots option.

2. Select the camera you want to edit the mode settings and enter the Detection & Alerts page.

3. You can change the Privacy mode, Detection, and Notification settings of the camera.

Tap Detection > Motion Detection to edit the motion detection function. You can adjust Motion Sensitivity.

Tap Detection>AI Detection to change your AI Detection feature, such as Person Detection.

4. After editing the detection settings, tap Detection & Alerts > Notifications to customize its current settings.

After completely presetting the Home or Away Mode, you can tap the card on the Tapo app>Cameras tab to switch all of your cameras’ detection settings to the mode you want.

.

How can I find the IP address of my Tapo&Kasa camera

Note: Some Tapo battery cameras or doorbells need to work with the hub and can’t connect to the router directly, which do not have IP address.

There are two methods to find the IP address of the camera.

Here we take Tapo C200 as an example.

Method 1: Via Tapo app

1. On the Tapo app> Home page, tap your camera model card to go to the Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Device Info and then you can find the IP address of your camera.

Method 2: Via the web management page of your router

Here we take the TP-Link router Archer C7 as an example.

1. Log in to the management page of your router.

2. Go to Advanced > Network > DHCP Server and locate the DHCP Client List section to find the IP address of your camera.

How can I view continuous recordings of Tapo&Kasa cameras on the Tapo app?

This article will show you how to view continuous recordings on the Tapo app.

Note:

For Tapo Cameras

Here we take Tapo C200 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

Click on Recording Schedule to see the detailed recording schedule settings.

Tap Edit on the Recording Schedule page if you want to change the Continuous Recording and Detection Recording schedule.

And please tap the tick icon at the top right corner to save your changes.

Step 3.

On the camera’s Live View page, tap Playback & Download, select the SD Card icon on the Playback page, select the date, and then you can drag the timeline to view the continuous recordings.

For Kasa Cameras

Here we take KC115 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

On the Live View page of the camera, tap Playback & Download > Playback to view all recordings. Drag the timeline and you can view recordings whenever you want and wherever you are.

What can I do if the video image is upside down on my Tapo&Kasa camera

Tapo&Kasa cameras support the function of Video Rotation, and if the camera video image is upside down on the Tapo app, please refer to the following steps to correct it.

Here we take Tapo C200 as an example.

1. On the Home page of the Tapo app, tap your camera model card or tap the Cameras tab>click on Manage on your camera model to go to the Live View page.

2. On the Live View page, tap the icon on the top right corner to enter the Device Settings page.

.

What can I do if I can’t find my Tapo camera on Tapo APP?

If your device does not appear on your app after completing the configuration process, please try the following troubleshooting suggestions:

1. If you are using a Wi-Fi wireless configuration to connect your camera, please check if the camera has successfully connected to the router. You can verify whether the camera is connected to Wi-Fi by checking the System light of your camera. For most Tapo Cams, if it is not connected properly, the LED light will blink red slowly. For the HomeKit version Camera, its LED light indicator will blink blue slowly. If the camera cannot connect properly, we recommend resetting the camera to factory default settings as per the User Guide and then reconfiguring the camera.

How to reset my Tapo camera

2. Check the DHCP settings on your router and ensure that the DHCP Server of your router is enabled. If the camera has already connected to the router properly, you will see the device in the client list of your router. If you don’t know how to do this, please contact your router’s customer support.

3. Please verify if there are any special symbols in your Tapo account（TP-Link ID） password. If there are, try to remove them and make the account password simpler by only using numbers and English letters. Then reset and add the camera from the beginning again.

4. Connect your smartphone to the same Wi-Fi network as your camera and check whether you can see it on the Tapo app. If you can see it, that means the camera fails to connect to the cloud for unknown reasons and you cannot access it remotely. In this case, verify if any firewall or security settings are blocking the connection to the Cloud Server. Temporarily disable any antivirus, firewall, or security software to see if it resolves the issue

.

5. Using a public DNS server may improve the connection, try changing your router’s DNS server settings to 8.8.8.8. If you don’t know how to do this, please contact your router’s customer support.

To eliminate potential issues with the router’s Wi-Fi network, it is recommended to use a mobile hotspot and configure the Camera to test its functionality.

Here are steps for using a mobile hotspot to test the Camera’s configuration:

Preparation: We suggest having two phones. Use one phone (Phone A) to create a hotspot and use another phone (Phone B) to download the Tapo app and complete the setup process.

Steps:

1. On Phone A, disable Wi-Fi and enable only mobile data.

2. On Phone A, navigate to phone settings and access the “Personal Hotspot” or “Mobile Hotspot” option, ensuring that the “Mobile Hotspot” feature is activated. Please make sure the created hotspot operates on a 2.4GHz network.

3. Set a unique name and password for the hotspot, different from your router’s Wi-Fi, to facilitate the Camera’s connection.

4. On Phone B, download the Tapo app. Follow the app’s instructions to add the device and complete the remaining setup steps as guided by the app.

Please contact TP-Link technical support with the following information if the issue persists after the above suggestions.

1) Your TP-Link ID or cloud account.

2) The model number of your TP-Link Cam and its MAC address.

3) The model number of the host router.

4) Whether you have tried all the suggestions listed above or not. If yes, what are the results?

<p>The post Tapo Smart Camera FAQ v1 first appeared on NVR IPCAMERA SECURITY.</p>

ATTENTION: Prior to purchasing and installing an accessory antenna, read the product specifications of your receiver to determine if your receiver has a weatherproof housing. Installing your weatherproof receiver outdoors provides a better line-of-sight between the receiver and the camera, increasing the strength of the wireless signal. See your product specifications to determine the weatherproof rating of your receiver.

The Directional Wireless Panel Antenna and the Omni-Directional Antenna are used to extend the range of one or multiple wireless or wire-free cameras.

Directional Wireless Panel Antenna (ACCANTD9)

Omni-Directional Antenna (ACCANTO8)

Use the 2.4GHz Directional Wireless Panel Antenna (ACCANTD9) to focus a wireless signal onto one specific wireless device (camera or receiver) to increase the range of transmission. A clear line-of-sight between the antenna and the wireless device needing range extension is required.

Use the 2.4GHz Omni-Directional Antenna (ACCANTO8) to enhance the signal of one or multiple cameras that are paired to a single or dual antenna receiver. You may also use two Omni-Directional Antennas to extend the range of all cameras paired to a dual antenna receiver.

REQUIREMENT: To connect the antenna directly to the camera or receiver, the device must have a removable SMA type antenna. Visit www.lorextechnology.com/compatibility to ensure the antenna is compatible with your camera or receiver model.

Lorex Wireless Cameras and Monitors guide 2024

Also Read  : Lorex Camera Troubleshooting

Recommended Antenna Installation Methods

Your antenna needs will vary depending on the setup of your camera system, the number of cameras that require range extension, and the number of channels on your wireless receiver. Review the scenarios below to ensure you have the correct antenna and installation method to meet your needs.

Click a setup scenario to see the recommended installation method:

Combining Accessory Antennas

If you have installed your accessory antenna according to the recommended installation methods and would like to enhance wireless signal strength even further, you may add an additional Directional Wireless Panel Antenna (ACCANTD9) directly to a camera. The additional Directional Wireless Panel Antenna can be used with a Directional Wireless Panel Antenna or with an Omni-Directional Antenna attached to the receiver.

Click an antenna combination to see recommended installation methods:

Scenario 1: Extend the range of one camera paired to a single antenna receiver

To extend the range of one camera connected to a single channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9).

The Directional Wireless Panel Antenna can be connected in two configurations.

Configuration 1. Connect the antenna directly to the camera

Configuration 2. Connect the antenna directly to the wireless receiver

REQUIREMENT: The antenna connects using an SMA cable and replaces the existing antenna on either the camera or wireless receiver. Check www.lorextechnology.com/compatibility to determine if your product is compatible with the antennas.

Scenario 2: Extend the range of one camera paired to a dual antenna receiver

To extend the range of one camera connected to a multi-channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9). Connect the Directional Wireless Panel Antenna directly to the camera.

Scenario 3: Extend the range of select cameras paired to a dual antenna receiver

To extend the range of select cameras on a multi-channel receiver, use the Omni-Directional Antenna (ACCANTO8).

Connect the Omni-Directional Antenna to one of the antenna ports on the wireless receiver.

REMINDER: Each antenna port on a dual antenna receiver is associated with specific camera channels. One antenna communicates with odd numbered channels (1, 3, and 5), while the other antenna communicates with even numbered channels (2, 4, and 6). See the table below for dual antenna channel configurations.

If you connect the Omni-Directional Antenna to an antenna port and your wireless signal does not improve, try switching the Omni-Directional Antenna to the other antenna port or pairing your camera to a different camera channel.

Scenario 4: Extend the range of all cameras paired to a dual antenna receiver

To extend the range of all cameras on a dual antenna receiver, connect an Omni-Directional Antenna (ACCANTO8) to each antenna port on the receiver.

IMPORTANT: Two Omni-Directional Antennas are required to accommodate this setup.

Combination 1: Combine two Directional Wireless Panel Antennas

If you are using a Directional Wireless Panel Antenna (ACCANTD9) to enhance the signal of a single camera with a single channel receiver, you can use an additional Directional Wireless Panel Antenna to further enhance the wireless signal.

Connect one Directional Wireless Panel Antenna directly to the camera and one Directional Wireless Panel Antenna directly to the wireless receiver. To maximize signal strength, it is recommended to aim the two antennas directly at each other with a clear line-of-sight.

Combination 2: Combine a Directional Wireless Panel Antenna with an Omni-Directional Antenna

If you are using an Omni-Directional Antenna (ACCANTO8) to enhance the signal of multiple cameras, you can further enhance the signal of a specific camera by connecting a Directional Wireless Panel Antenna (ACCANTD9) directly to the camera.

A clear line-of-sight between the Directional Wireless Panel Antenna and the Omni-Directional Antenna is recommended to maximize signal strength.

Lorex SD Pro App: Changing / resetting the password

If the password for the Lorex SD Pro app to view the Wireless Home Monitor is lost or forgotten it will need to be reset.

To reset the Lorex SD Pro app password:

1.Ensure that your Wireless Home Monitor is connected to a network router using the included Ethernet cable.

2.On the Wireless Home Monitor tap the Menu icon ().

3.Use the joystick to select Settings > Network > Reset Password.

4.Select Yes to confirm.

5.Tap the Menu icon () repeatedly until all the menus are closed.

6.Launch the SD Pro app and enter the default password. Refer to your user manual for your default password. You will be prompted to create a new password.

Lorex SD Pro App: Setting up Wireless Home Monitor remote access

You can access and view wireless cameras from a Wireless Home Monitor system using an iPhone, iPad, or Android smartphone or tablet using the Lorex SD Pro app. It is available at the App Store or Google Play Store.

Prerequisites:

To set up the mobile application:

LW2700 Wireless Home Monitor: Included cables and accessories

LW2700 Series Wireless Home Monitors support wireless cameras using a wireless signal. They do not have an internal battery and require a connection to a power source. Refer to your user manual for model specific information on cables and accessories. Click here for downloads and documentation for your product.

Most wireless home monitors include the following cable connections and accessories when purchased:

Network: Wireless camera Internet requirements

Standard wireless cameras that connect to a DVR / NVR, do not need access to the Internet to function. Stand-alone IP cameras do not require an Internet connection for basic functions, but an Internet connection is required for full functionality.

Security Cameras: Understanding Field of View (FOV)

Field of View (FOV) is the maximum observable area that is seen at any given moment through an optical device such as a camera lens. The coverage of the area can be measured using the horizontal and vertical distances to find the diagonal of the area in degrees. Mathematically, the FOV is calculated using the horizontal dimension of the sensor (h) and the Focal Length (F).

You can find the camera’s Field of View details in the Specifications sheet. Click here for additional support content including security camera documentation.

The Camera Lens, Sensor and Focal Length

Focal length (F) is the distance between the center of a lens and its sensor. The size of the lens is the aperture size.

These factors affect field of view. A narrower focal length captures more of the scene and displays a larger field of view. A wider focal length magnifies a scene and decreases the field of view. The higher the focal length value the lower the FOV.

Types of Camera Lenses

Fixed: a fixed camera focal length provides an Angular FOV which is permanently set and cannot be adjusted by the user. Varifocal: the camera focal length can be manually adjusted by the user. Generally, this is done manually with screws or dials. At Lorex we have motorized varifocal cameras that allow you to digitally zoom using your phone or NVR without losing details. These lenses provide flexibility and customization for your camera image needs.

The importance of Field of View

A wide angle lens or smaller lenses produce a greater field of view and captures more objects in a scene enhancing your ability to cover larger and wider areas such as foyers, parking lots or warehouses.

A narrow angle lens or larger lenses produce a smaller field of view; capturing a limited area, but the camera quality image improves in detail. These are designed to monitor a specific object, such as cash registers, entrances/exits, hallways or objects of value.

How to Calculate the FOV

To calculate the FOV requires the sensor size and the focal length of the lens: h = Sensor Size F = Focal Length of the Lens

FOV is represented by this equation: FOV = 2tan-1(h) / 2F

Example: h = 4.7mm F = 6mm FOV = 2tan-1(h) / 2F = 2tan-1(4.7)(12) = 2tan-1(0.39) = 2(21.4°) = 42.8°

W482CAD – 2K Wi-Fi Camera : Frequently Asked Questions

The following FAQ article answers many of the general questions about the 2K Wi-Fi Camera with Smart Deterrence (W482CAD). Where applicable, the FAQ includes links to articles where you may find more information.

.

Where do I place my Lorex 2K Wi-Fi Camera?

.

How should I position my Lorex 2K Wi-Fi camera?

When mounting the camera on a wall, make sure of the following:

 Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

.

How do I enable motion detection and person detection?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap  icon to enable Motion Detection.

Note: If motion detection is disabled, general/person/vehicle detection will automatically disable and you will not receive any motion detection notifications in the Lorex App.

.

How do I customize Motion Zones™?

Motion Zones™ allows you to customize your device’s motion detection region. Motion Zones™ screen consists of the following settings:

To set Motion Zones™

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap Motion Zones™.

 For full instructions on how to set customized Motion Zones™, see Configuring Motion Zones™.

.

Why am I receiving so many notifications?

There are a few ways you can lower the number of notifications you are getting.

.

How do I enable Color Night Vision?

1.Lauch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap  icon to disable Auto Night Vision.
Note: Disabling Auto Night Vision will force the camera into Color Night Vision mode. Recommended in low-light conditions.

.

How to activate Two-Step Verification?

1.Launch the Lorex App.

2.Tap Settings.

3.Tap Account Settings.

4.Tap Two-Step Verification.

5.Tapicon to enable Two-Step Verification.

For detailed setup instructions, see Two-Step Verification Setup.

.

How to optimize video quality?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Video Settings.

4.Tap  icon to enable HDR (High Dynamic Range).

Note: Enabling HDR optimizes video picture in high-contrast conditions such as under-lit and over-lit areas.
By default, the video quality is set to High (2x1080p HD).

.

What is Home & Away™?

Lorex App can automatically use your location to manage your notifications when you are at home or away. The app will notify you when you are inside/outside of your set home perimeter.

To start using this feature, navigate to your mobile device settings and enable Location services for Lorex App.

For detailed setup instructions, see Configuring Home & Away™.

.

How do I activate the LED deterrence light when motion is detected?

1.Lauch Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Deterrence Light Brightness.

4.Tap  icon to enable camera’s deterrence light whenever motion or person is detected.

.

How do I remove the 2K Wi-Fi Camera from my account?

1.Launch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Remove Device.

.

How to permanently delete data of 2K Wi-Fi Camera?

Refer to Formatting Device Storage for more information.

.

Does my device support WPA2 or WPA3?

Your device supports Wi-Fi Protected Access 2 (WPA2) which is the industry standard security protocol for Wi-Fi networks. WPA2 offers security against unauthorized access and data interception and is supported by most Wi-Fi routers including those that support both WPA2 and WPA3. It employs Advanced Encryption Standard (AES), an encryption mechanism, which secures communication between your camera and Wi-Fi network to keep transmitted data confidential. For information on which devices support WPA2 and which devices support WPA3, please refer to “WPA2 and WPA3 Supportive Devices.”

.

What are the compatible SD cards?

Refer to Compatible SD Cards and Storage Sizes for more information.

.

What devices are compatible with the 2K Wi-Fi camera?

Refer to Product Compatibility Chart for more information.

W482CAD – 2K Wi-Fi Camera : Installation

This article provides instructions to install your Lorex 2K Wi-Fi camera with Smart Deterrence (W482CAD).

.

What is included in the box?

The above contents are based on one camera.

.

How to connect with Lorex App

3.Open the Lorex App app and create an account or login with your credentials.

4.Tap  icon to add a new device, then follow the in-app instructions to complete the device setup.

For full instructions on Lorex App setup, see Connecting with Lorex App.

.

How to mount 2K Wi-Fi Camera to the wall

.

How to mount 2K Wi-Fi Camera to the ceiling

Wi-Fi Security Cameras – How to Read a MicroSD card

To view the contents of a MicroSD card on a laptop or computer, follow these steps:

a. Select the day to play back:

b. Click on the available folder:

c. Within the folder, click either the day folder (Video files) or the jpg folder (Snapshots):

d. Click to select a video time from 00 – 23 hours:

6.Click the MP4 video file to view the video. 

Wireless Home Monitor: Audio not working

If the audio is not working on your Wireless Home Monitor:

• Ensure that the protective film is removed from the camera lens.

• Ensure that the monitor volume is not muted. A mute icon () will be visible on the screen if the volume has been muted.

• Turn the monitor volume up using the volume buttons on the side of the unit. Location will vary by model. For exact location of volume buttons for your model, refer to your user manual. Click here for downloads and documentation for your product.

• The camera must be in Full Screen mode for audio. Tap the Channel Select icon () to switch between channels in Full Screen mode. Audio is disabled in Quad mode.

If audio is not working after increasing the volume and viewing in Full Screen mode, restore the system to default settings.

To restore your monitor to default settings:

CAUTION: Restoring to default settings will erase any setting input on the monitor. Your monitor will need to be reconfigured.

1.On the monitor tap the Menu icon ().

2.Use the joystick to select Settings > Default Settings.

3.Select Yes.

.

<p>The post Lorex Wireless Cameras and Monitors guide 2024 first appeared on NVR IPCAMERA SECURITY.</p>

The following Swann Security cameras can only be viewed and accessed via the Swann Security app from a mobile device.

They cannot be added to Swann security system recorders, such as DVRs, NVRs, and NVWs. These recorders are compatible with specific system camera models.

Can a SWIFI camera work without Internet?

Internet is required as the SWIFI cameras communicate to the P2P server using the Internet to stream to the Swann Security app and upload recordings to the cloud.

Compatible Routers

Any of the following routers are compatible provided they have a 2.4 GHz frequency:

For more information, see What router WiFi frequency band is my SWIFI camera compatible with: 2.4GHz VS 5GHz Frequency?

Compatible Wi-Fi extender or repeaters

It is possible for the SWIFI camera to pair to the router via WiFi extender if the extender is compatible and setup correctly to the router. Troubleshooting and configuration of your extender’s settings have to be performed by your router manufacturer support team, Internet Service Provider or your IT department. See this article: How to boost your WiFi signal and extend WiFi range.

Tip: Try to pair the camera to the router first to check whether its internal network adapter is working. If it works via router but not extender, then there’s a chance the extender is not compatible.

Swann Wi-Fi camera FAQs

Read More : Swann Security Troubleshooting All Devices

Not Compatible / Not Recommended

We do not recommend SWIFI cameras to be connected to the following devices because they cannot provide the necessary network configuration information to the camera to allow it to join the network automatically unless your network device is configured. Troubleshooting and configuration of your device’s settings have to be performed by your router manufacturer support team, Internet Service Provider or your IT department.

Can I view my SWIFI camera on a TV / computer or record to a DVR / NVR?

The cameras above are hub-free. A hub is a base station or recording/storage device that connects via the Internet to the cameras. In contrast, a hub-free camera operates on Wi-Fi exclusively without requiring any additional hardware to store footage. 

A hub-free (standalone) Wi-Fi camera is only capable of:

These features make a hub-free Wi-Fi camera suitable for users who prefer a wireless setup, easier DIY installation, less hardware, and less footage to check in low-traffic areas of view. 

Accessing live view, recordings, and other settings are covered in the manuals below for your device: 

How do I tell whether my router’s WiFi signal is 2.4GHz or 5GHz for pairing a SWIFI camera?

This is one of the most common reasons why a connection will fail while trying to pair a SWIFI camera to your Swann Security account. If you try to pair a SWIFI camera to the incorrect frequency or SSID name, the error that appears on the app can be one of the following:

Via Mobile Device Settings

One way to tell if the phone is connected to the correct frequency of the router is by checking the name of the SSID (the default name of your router’s WiFi hotspot): 

In the example above, the router has multiple SSIDs. An SSID that has “_2.4GHz,” “24G,” “2.4,” or “24” appended at the end is most likely a 2.4GHz signal. This is the network your phone needs to be connected to before you start pairing a SWIFI camera. 

To avoid connecting to a 5GHz SSID, see How to forget 5GHz connection for pairing a SWIFI camera.

Via Router GUI

If you see two or more Wi-Fi network names that belong to you without 24 or 5, then one may be a 5 GHz band. To identify which name uses 2.4 GHz or 5 GHz, login to your router’s settings. 

For assistance with accessing or navigating your router, contact the manufacturer of your router or your Internet Service Provider if you do not know. Swann Tech Support can only assist in pairing IF your router has a 2.4GHz signal and if you already know the correct WiFi credentials of your router.

How to change the time zone of my SWIFI camera in the Swann Security app?

The error “Device Timezone Out of Sync” appears if your camera’s time zone is different from your phone app’s time zone. 

If your camera is in a different location (with different time zone) than your mobile device, you can ignore hit Cancel. 

If the date and time displayed on the camera’s Live View is incorrect, do the following: 

Repeat each step for each camera device paired to your Swann Security account.

How to create Guest account on a WHD-PTCAM using SwannView Link software?

Installing SwannView Link

Adding the camera

Since the computer is on the same router or modem already, when you open SwannView Link the camera will be auto-detected, but the password will not be entered yet. You will see the error message below. Just click on OK.

How to forget 5GHz connection for pairing a SWIFI camera

Some mobile devices have a tendency to switch between hotspots or SSID automatically. This can disrupt the pairing process when setting up your SWIFI camera to your mobile device. 

To avoid connecting to a 5GHz signal or the wrong hotspot during pairing, forget the 5GHz connection: 

Note: If you see a WiFi name that ends with _ext, it is most likely a WiFi extender.

How to hard reset Floodlight Security Camera (SWIFI-FLOCAM2 / SWWHD-FLOCAM)

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Locate the Reset button (see below figure) on the SWIFI-FLOCAM2 / SWWHD-FLOCAM. It is behind the camera module covered by a rubber flap.

2.Press and hold the Reset button (for 20 seconds).

3.When the blue LED indicator on the camera turns off, release the Reset button.

4.The camera will start the factory reset process which can take up to 2 minutes.

5.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue).

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to hard reset SWIFI-2KOCAM / SWIFI-SPOTCAM / SWWHD-OUTCAM

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Locate the Reset button (see below figure) on the twin cable of the SWIFI-2KOCAM / SWIFI-SPOTCAM / SWWHD-OUTCAM.

2.Press and hold the Reset button (for 20 seconds).

3.When the blue LED indicator on the camera turns off, release the Reset button.

4.The camera will start the factory reset process which can take up to 2 minutes.

5.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue).

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to hard reset SWIFI-BUDDY

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Ensure the camera has been fully charged for at least 4 hours prior.

2.Locate the SET button and RST pinhole (see below figure) on the back of the camera.

3.Press and hold the SET and RST button (pin required).

4.After 2 seconds, release RST button.

5.Once blue LED turns off (or after 15 seconds), release SET button.

6.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue) and you will hear it say “Ready for pairing”.

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to hard reset SWIFI-CORECAM / SWIFI-COREPRO

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Ensure the camera has been fully charged for at least 4 hours prior.

2.Locate the Reset button (see below figure) on the camera.

3.Press and hold the Reset button (for about10 seconds).

4.Once the LED indicator on the camera turns off, release the Reset button.

5.The camera will start the factory reset process which can take up to 2 minutes.

6.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue).

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to hard reset SWIFI-PTCAM2 

How to hard reset SWIFI-XTRCAM

How to set SWIFI-MOTION / SWIFI-WDOOR / SWIFI-LEAK / SWIFI-ISIREN to pairing mode

Setting the sensor or siren to pairing mode will:

Note: If the sensor or siren is paired to your account and the Wi-Fi details did not change, it will connect back to the same network once pairing mode times out after 3 minutes.

Why does my WiFi camera stop recording motion after a minute?

Wireless standalone cameras can only record by PIR/motion. Where the camera is mounted can have an impact on how effective movement is picked up and recorded. 

Reasons:

 .

Fix: Reposition the camera or add another camera for a different angle of view.

The ideal position of the camera is 7-8 feet high, pointing downwards at an angle to cover the area where people will be walking across the camera’s path.

Can I pair my SWIFI-BUDDY to another receiver/chime?

How do I share my WHD-PTCAM?

Sharing the WHD-PTCAM

Scan to add a camera

How many files can I store in my SwannCloud account?

As of now, the SwannCloud can let you record 15 seconds per event and it will be stored approximately 5 days. In the future, there will be some other options to be chosen with regards to this but there are no approximate date of arrival yet.

How to check the battery level of my Wi-Fi camera?

This applies to SWIFI-CAM, SWIFI-CORECAM, SWIFI-COREPRO, SWIFI-XTRCAM, SWIFI-BUDDY, SWIFI-MOTION, SWIFI-LEAK, SWIFI-WDOOR, SWIFI-SIREN.

There are 2 ways:

• Dim than normal (for sensors)

• Blinking purple (for SWIFI cameras)

Note: If the Device Status is Disconnected, the battery level shown is the last that was synced to the Swann Security server and your phone before the camera disconnected. This means the current battery level cannot be seen until the camera is recharged and reconnected to the network. 

How to delete recordings of a SWIFI camera in the Swann Security app

There are two ways to delete recordings of a standalone Wi-Fi camera that is compatible with the Swann Security app.

Delete one or few recorded clips: 

1. Go to Playback.

2.Tap on the Storage (microSD card) icon on the top beside the logo.

3.Select your device. (pause and wait for the clips to load. If there are none, it means that the camera does not have a microSD card or internal storage)

4.Tap on the trash / bin icon beside the recording with timestamp you wish to remove.

Delete all recordings (Format the internal storage)

Note: Formatting deletes all recordings from local storage or microSD card. It will not delete the recordings from the cloud. Once deleted, they cannot be recovered.

1.Go to Devices > select your device.

2.Go to Settings > System Settings.

3.Tap Format.

4.Select Confirm.

How to hard reset 4K Floodlight Camera (SWIFI-4KOCAM)

How to hard reset SWIFI-2KICAM

How to hard reset SWIFI-ALERTCAM / SWWHD-INDCAM

How to hard reset SWIFI-CAM

How to hard reset SWIFI-FOURTIFY

How to hard reset SWIFI-TRACKCM

Performing a factory or hard reset of the camera will:

How to factory reset via physical button

1.Locate the Reset button (see below figure) on the SWIFI-TRACKCM. 

2.Press and hold the Reset button (for 20 seconds).

3.When the blue LED indicator on the camera turns off, release the Reset button.

4.The camera will start the factory reset process which can take up to 2 minutes.

5.Once factory reset is complete, it will be in Pairing mode (LED will be in slow blinking blue).

After you factory reset your device, you’ll have to pair it with your Wi-Fi network again.

How to playback recordings? ( via Swann Security App)

Playback tab

Open Swann Security, login your account, tap on Playback

NOTE: As of v2.7.45 in Android, you can get a preview (like a GIF) instead of a generic icon for a recorder’s clip if you enable Show playback preview under Stream Option. 

• Go Back to see results. Tap the burger icon at the upper left.

Playback Interface

How to test Wi-Fi password for pairing SWIFI cameras

This step is useful: 

 How to forget the network in your mobile device: 

.

<p>The post Swann Wi-Fi camera FAQs first appeared on NVR IPCAMERA SECURITY.</p>

Reolink NVR Setup Guide, Use this NVR with Reolink PoE cameras and you can get a professional, reliable and DIY security camera system. You can play back any recorded video, back up local data, and do more. For more features, refer to RLK8-810B4-A NVR security system.

If you have ordered an RLN8-410 or are interested in it, and want to get some basic information about this product before placing it in use or placing the order, you may refer to the below introductions.

This article includes the following 4 parts which will help you quickly understand the use and working principles of the NVR:

Unboxing for RLN8-410

Product Overview

You may find detailed information about the structure and components of the NVR below. 

Installation

You can connect either hard-wire the PoE cameras or connect WiFi cameras wirelessly (except for battery-powered cameras) to the NVR. Below is a common network topology of the connection. 

For more instructions on the configurations, you may refer to the sections Wired Connection and Wireless Connection. 

Wired Connection

Applies to cameras that are hard-wired to the NVR. 

Step 1. Connect your Reolink IP cameras to the Reolink PoE NVR. 

Step 2. Log into your NVR, and go to the IP channel.

Old UI: 

New UI:

Step 3. Select Auto Add so that all the cameras in the same LAN can be automatically shown on the list.

Step 4. If you have never changed the password of the IP cameras (the default password of the IP camera is blank) and there are enough channels for all the cameras, you may press Apply to add all the IP cameras to the NVR.

Step 5. If you have changed the User Name and the Password of your cameras, please put the password of the camera to log in.

Old UI:

Please drag the menu bar to the password column and use the soft keyboard to input the required information.

New UI:

Please click Modify to input the required information.

Step 7. Click Apply to save and apply the configuration.

For more detailed instructions, you could refer to the articles below:

Reolink NVR Setup Guide

Read More : Reolink NVR IPCAM how to reset password methods

Wireless Connection

Applies to wifi cameras (except for battery-powered cameras) attempting to add to the NVR. 

Step 1. Connect the WiFi camera to the same LAN as the PoE NVR.

Step 2. Connect the camera to the WiFi of the router. 

Step 3. Add the camera to the PoE NVR: Toggle the “Auto add” on and hit “Modify” to input the login credentials. 

Old UI:

New UI:

For more details of the configurations, please refer to the links below: 

Initial Setup

You can do the initial setup on a monitor or TV connected with an HDMI/VGA cable, or through the Reolink App or Reolink Client.  

Step 1. Connect the NVR to a Monitor or TV via the VGA or HDMI cable.
Step 2. Connect the camera’s RJ45 network socket to any PoE Camera port on the NVR using the Ethernet cables provided.
Step 3. Connect an Ethernet cable from the LAN port of the NVR to the LAN port of your router.
Step 4. Connect the mouse to the USB port.

Step 5. Connect the Power Adapter. Please use the supplied power adapter. For the PoE NVR device, it is 48 volts.
Step 6. And then you will see the below splash screen. System booting up might take a few seconds.
Step 7. Follow the Setup Wizard to set your NVR, click Next to continue and at the last step, click Finish to save all the settings.
For more detailed instructions, you may refer to the articles below:
.

Step 1. Power the camera and the NVR, then launch the Reolink App on your phone.
Step 2. During start-up, you will find the NVR shown on the Delive List automatically on Reolink App.

Step 3. Click the device you want to add to start initialization.

Step 4. For security considerations, you need to create a password for the first time.
Step 5. Then name your device and modify other settings on the second step page.
For more detailed instructions, you may refer to the article: How to Do Initial Setup for Reolink NVR via Reolink App.

Step 1. Click the “+” icon, select UID, then fill in the blanks with the UID number of your NVR, See How to find the UID of your device.

Step 2. Create a device password, then click Next.
Step 3. Create a device name then click Finish.
For more detailed instructions, you may refer to the article: How to Initial Set up NVR via Reolink Client (New Client).

.

How to Add Reolink Cameras to Reolink PoE NVR

Reolink PoE NVR allows you to record videos for Reolink IP cameras without using a computer. To do that, you need to add the camera to the NVR first. The cabling for PoE NVR is shown below.

Applies to: All Reolink IP cameras (excluding battery-powered cameras) and PoE NVRs with the hardware version H3MB02/H3MB16

You may then follow the steps below to add Reolink cameras to Reolink PoE NVR.

Step 1. Connect your Reolink IP cameras to the Reolink PoE NVR. There’re two different ways of powering your IP cameras:

There are two ways of connection:

 a. Connect the PoE cameras to the PoE NVR directly via an Ethernet cable. (suggested way)

 b. Alternatively, you can power on this camera by a PoE switch/injector and connect to your router, then add this camera to the POE NVR system in the same local network.

All Reolink WiFi cameras (except for battery-powered cameras) can be used with Reolink PoE NVRs, too. You need to connect them in LAN, the connection diagram is as below:

Note: Make sure all the IP cameras you want to add to the NVR are connected to the same network (LAN) as the NVR. Otherwise, the cameras won’t be shown on the scanned list and cannot be automatically added to the NVR.

Step 2. Log in to your NVR, and go to the IP channel.

Step 3. Select Auto Add, and click Scan so that all the cameras in the same LAN can be automatically shown on the list.

Note: The number of cameras that can be added to the NVR may vary depending on the NVR channel numbers of the NVR.

Step 4. If you have never changed the password of the IP cameras (the default password of the IP camera is blank) and there are enough channels for all the cameras, you may click Apply to add all the IP cameras to the NVR.

However, if you have changed the login passwords of the IP cameras or there is no spare channel to display all the IP cameras, you may need to go through a few more steps.

Step 5. If you have an 8-channel NVR and more than 8 IP cameras, please choose the 8 of them you want to add to the NVR and manually change the other cameras’ Channel to None.

Note: You may assign the IP cameras to any channel you want, but you cannot have two cameras on the same channel, otherwise configurations would fail to be saved.

Step 6. If you have changed the User Name and the Password of your cameras, please drag the menu bar to the password column and use the soft keyboard to input the required information.

Step 7. Click Apply to save and apply the configuration.

Here is a video to show how to add WiFi cameras to PoE NVR:

Note:

RLN8-410 (with the hardware version H3MB02) and RLN16-410 (with the hardware version H3MB02 and H3MB16) don’t work with 8MP cameras including B800/D800. The 4k cameras can only work with RLN8-410-E (with the hardware version H3MB16 and H3MB18) and RLN16-410 (with the hardware version H3MB18). And only the RLN8-410(H3MB18, N3MB01) and RLN16-410 (H3MB18) support the Human/Vehicle detection function.

.

How to Initially Set up Reolink NVRs with Monitor Connected (New UI)

Want to do the initial setup for Reolink NVRs on a monitor? This article will do you a favor.

Applies to: RLN8-410 (hardware version H3MB18/N2MB02/N3MB01/N7MB01), RLN16-410 (hardware version H3MB18/N6MB01), RLN36.

You may follow this guide for proper cabling and initial setup of your Reolink NVRs with a monitor connected.

Here is a video for your reference:   

Here is a diagram that will help you learn each option on the PoE NVR.

Now, please refer to the following steps to set up your NVR.

Step 1. Connect an Ethernet cable from the LAN port of the NVR to the LAN port of your router. And connect a mouse to the USB port.

Note: You can right-click to open the Menu on the live-view page.

Step 2. Connect the NVR to a Monitor or TV via the VGA or HDMI cable. 

Notes:
1. If there is no display, please connect it to a VGA monitor and change its resolution to 1920*080.
2. If you need audio output on your TV monitor, the resolution MUST be set to 1920*1080 or 1280*720.

Step 3. Connect the camera’s RJ45 network socket to any PoE Camera port on the NVR using the Ethernet cables provided.

Step 4. Connect the NVR to a power outlet with the supplied power adapter, and then turn on the power switch.

Step 5. And then you will see the below splash screen. System booting up might take a few seconds.

Note: If the monitor screen remains black, check if you flip on the power switch on the back of the NVR.

Step 6. General configurations. Set up the language, screen resolution, date Format, and time format. Then click Next.

Step 7. DST settings. Set up the system time and time zone, and enable/disable the DST option. Then click Next.

Step 8. Create a password for your NVR, and enable/disable screen auto-lock. Then click Next.

Step 9. Set up a password security question. Then click Next.

Step 10. Name your device and manage your HDD. Then click Next.

Step 11. Configure the network for your NVR. Then click Next.

Step 12. Set up E-mails for your NVR up to your need. Then click Next.

Done! Here is a sum-up of the Wizard Setup.

Troubleshooting for RLN8-410

Here are some troubleshooting tips for RLN8-410. You may check whether your camera’s issue is listed below. If not, you may go to the Troubleshooting section to find suggestions for more issues or you may contact Reolink support for help.

If the NVR stops working and the power LED is not on, you may follow the troubleshooting tips listed below to solve the problems.

Cause 1. Power adapter issue

Solution: Check the status LED on the power adaptor of the NVR. If the LED isn’t on, please plug the power adaptor into another socket as well as change another working power adaptor (48V) for a try. If the LED is on, please check the HDD issue below.

Cause 2. HDD issue

Solution: Please unplug the HDD and check if the NVR will power on when no HDD is plugged in. You may open the NVR housing and refer to How to Change the HDD for Reolink NVR to remove the HDD. 

Cause 3. The voltage is not sufficient.

Solution: Unplug the cameras. If the NVR power LED goes on, please replug the camera back one by one. 
For more information, please check POE NVR Failed to Be Power on.

When you connect the NVR via a monitor and start up the NVR, the NVR is freezing on the Reolink Logo Page. There are several possible causes for the issue. You may follow the troubleshooting tips listed below to solve the problem. 
.

Cause 1. HDD issue

Solution: Please unplug the HDD and check if the NVR will power on when no HDD is plugged in. You may open the NVR housing and refer to How to Change the HDD for Reolink NVR to remove the HDD.

Cause 2. The voltage is not sufficient. 

Solution: Unplug the cameras that are connected to the NVR and check if the NVR can boot up.

Cause 3. Firmware issue

Solution: Please refresh the firmware using a USB drive. 

For more details, please check the article NVR is Freezing on the Reolink Logo Page.

If there’s no video output on the monitor from Reolink NVR, you may follow the troubleshooting tips listed below to solve the problem. There are several possible causes for the problem.
.

Cause 1. The video output resolution of the NVR is not supported by the monitor/TV. 

Solution: Ensure that the lowest resolution of the TV/monitor is no less than 720p.

Cause 2. HDMI/VGA port on the NVR or the monitor/TV is defective. 

Solution: Check whether the cable is defective by using it to connect other devices to the router and see if it works. Or please test with another HDMI/VGA cable or monitor/TV. 
For more information, please check the article No Video Output on the Monitor/TV from Reolink NVR.

If you found that the NVR is rebooting, below are some possible causes and solutions that you may refer to. 

Cause 1. UPS issue

Solution: If you use the UPS to power the NVR on, please plug the NVR directly into a wall socket and have it run for one or two days then check if the NVR reboots.

Cause 2. HDD issue

Solution: Please unplug the HDD and have the NVR run for one or two days then check if the NVR reboots. 

Cause 3: The cameras and the NVR are both grounded. 

Solution: Please unplug all the cameras from the NVR and have the NVR run on its own for one or two days and check if it still reboots (Please disable auto-reboot before you run the test). If the NVR doesn’t reboot, the issue may be caused by both the NVR and the cameras being grounded. Please check whether the cameras and the NVR are grounded. If yes, please unground either the NVR or the cameras to fix the issue. 

For more details, please refer to POE NVR Reboots Automatically.

If you noticed that after plugging the new cameras into the NVR, the camera’s image does not show up on the monitor and it prompts “video loss”. The following troubleshooting may be helpful to you.

Cause 1. No available channels

Solution: Delete the offline cameras from the IP channel, or manually assign a channel for the camera. 

Cause 2. The new camera is distributed with the same IP address as the other cameras. 

Solution: Please reset the camera and restore the NVR.

Cause 3. The camera shows “invalid password” or “incorrect username and password”. 

Solution: Put the password of the camera.

For more details, please refer to Fail to Add PoE Cameras to NVR.

If you fail to connect the NVR through the network, below are some possible causes and solutions for your reference.

Cause 1. NVR is powered off. 

Solution: Check whether the power light is on. If it is off, please refer to POE NVR Failed to Power on.

Cause 2. The LAN port is defective. 
Solution: Please check if the LAN port on the back lights up or not. If not, please try another ethernet cable and port on the router for a test.
Cause 3. The gateway is 0.
Solution: Please change a router or switch and further check the issue. Please also reboot the NVR and check if the issue remains.

Please upgrade the NVR’s firmware to the latest firmware.

For more details, please refer to Failed to Connect NVR in LAN.

When you fail to playback the videos of the NVR and find the capacity of the HDD is 0GB, or it shows “HDD not detected”, here are some possible causes for your reference.
.

Cause 1. The firmware version of the NVR is old. 

Solution: Please find out the firmware version of the NVR and go to the Download Center to download and unzip the package to upgrade it. 

Cause 2. The format of the HDD is wrong. 

Solution: Please format/init the HDD to try again, please refer to Check/Init HDD via PoE NVR.

Cause 3. Defective HDD

Solution: Please unplug and replug the HDD to see if it works. If possible, please test with another working HDD. 

For more details, please refer to HDD Capacity Shows 0GB.

.

Configuration – RLN8-410

RLN8-410 is an eight-channel network video recorder that is used for centrally controlling the devices that are connected to it. With diffenernt hardware versions, RLN8-410 can acheive different features. Generally, it can be used for setting up detection for the cameras, managing the channels, upgrading the devices that are connected, etc. 

To better learn the working principles and settings of this NVR, here are some instructions for your reference.

Note: You can click on the keywords below to jump to the corresponding section.

Motion Detection

Generally, Reolink cameras are capable of motion detection. RLN8-410 is able to manage the configurations of motion detection for cameras that are connected to it. 

To achieve the detection settings you want, you could try on the monitor, the Reolink App, or Reolink Client. Below are some instructions for your reference. 

Old UI: 
1. Log into your NVR on a monitor and go to the NVR settings. 
2. For configuring motion recording, go to “Menu>Recording>Schedule” page, then select the channel (camera) and check the Enable box. Select “Motion” and tap on the grids to choose the time that you want to enable motion detection recording, and then click Apply to save the settings.

3. For setting up motion detection, go to “Menu>Alarm”. Click on “Motion Detection>Set”, then you can configure the motion detection settings (including motion detection area and sensitivity), motion schedule, and action.

For more details, please refer to:
How to Set up Motion Detection Recording via Reolink PoE NVR
How to Set up Motion Detection Area via Reolink PoE NVR
How to Set up Motion Detection Sensitivity via Reolink PoE NVR

New UI:
1. For setting up motion recording, log in to your Reolink PoE NVR on a monitor. Go to “Menu>Surveillance>Daily Schedule” page.

2. For setting up motion detection for cameras, go to “Settings>Camera>Detection”. 

For more details, you may refer to the articles below:
How to Set up Motion Detection Recording via Reolink PoE NVR (New UI)
How to Set up Motion Detection Area via Reolink PoE NVR (New UI)
How to Set up Motion Detection Sensitivity via Reolink PoE NVR (New UI) 

1.Click  button to go to Device Settings>Channel Setting>Motion Detection.

.

For more details, please refer to:
How to Set Motion Detection Schedule for NVR via Reolink APP 
How to Set up Motion Detection Sensitivity via Reolink App 
How to Set up Motion Detection Zones via Reolink App 

.

For more details, please refer to:
How to Set Motion Detection Recording for Reolink NVR via Reolink Client (New Client) 
How to Set up Motion Detection Area via Reolink Client (New Client) 
How to Set up Motion Detection Sensitivity via Reolink Client (New Client) 

Smart Detection

Smart detection includes Smart Person, Vehicle, and Pet Detection. It is based on the traditional motion detection but with advanced algorithms and technology, which can tell people, vehicles, and pets from other objects. You can set up detection sensitivity, detection zone, object size, etc. for the cameras via the NVR. 

Please notice that for 8-channel NVRs, only if the hardware version is N2MB02/N3MB01 can it achieve the smart detection settings.
To check the version of your NVR, you can refer to How to Find out System Information via Reolink App or contact Reolink Support Team for confirmation. 

On Monitor

1. Please go to the Menu of your NVR, and go to “Surveillance>Record>Daily Schedule”.
2. Under the Record Schedule page, please choose the camera model/channel you want to set up the record schedule. 
3. Under the Alarm schedule, please enable/choose the detection type and then enable the time & date for detection.

There are three detection types: ” Any Motion”,” Person” and ” Vehicle”. Please enable/choose either of them or combine two options or all of them together according to your own needs.
For more details, you may refer to the articles below:
How to Set Smart Detection via the PoE NVR System (New UI) (Video)
How to Set up Smart Person/Vehicle Detection via POE NVR system
How to Set up Smart Person Detection only via Reolink POE NVR System 
How to Set up Vehicle Detection only via Reolink PoE NVR System 
How to Set the Maximum and Minimum Object Size via POE NVR System (New UI) (Video) 

.

On Reolink App

.

For more details, please refer to:

How to Set up Smart Person/Vehicle Detection via Reolink APP  
How to Set up Smart Person Detection only via Reolink APP 
How to Set up Smart Vehicle Detection only via Reolink APP 

.

On Reolink Client

.

For more details, please refer to:
How to Set up Record Schedule via Reolink Client (New Client) 
How to Set up Smart Person Detection only via Reolink PC Client 
How to Set up Smart Vehicle Detection only via Reolink PC Client 

.

Buzzer

Buzzer includes motion buzzer and exception buzzer. It is the sound that comes from the NVR when the cameras detect motions or the NVR detects abnormalities. Conditions like HDD full, HDD error, network disconnected and IP conflict will be marked as exceptions.

You could set up motion buzzer via the monitor, Reolink App, or Reolink Client. Please notice that the exception buzzer can only be set up via the monitor.
Below are some basic instructions for your reference. 

Old UI:
1. Set up Motion Buzzer:
Go to “NVR>Menu>Alarm>Motion>Action”, and tick Buzzer for selected cameras (channels). Click Apply to save the settings.

2. Set up Exception Buzzer:
Go to “NVR>Menu>Alarm>Exception”, select the exception type you want, and tick Buzzer then click Apply to save the settings. Choose the Type for the exception alarm based on your requirement.
For more details, please refer to:
How to Set up Motion Buzzer for PoE NVR
How to Set up Video Loss Buzzer for PoE NVR
How to Set up Exception Buzzer for PoE NVR

New UI:
1. Set up Motion Buzzer:
Go to “Settings>Surveillance>Buzzer”, and enable Buzzer. Then click “Daily schedule” to choose the schedule and detection type.


2. Set up Exception Buzzer:
Go to “Settings>Surveillance>Buzzer (Exception)” and select the exception type you want.

For more details, you may refer to the articles below:
How to Set up Motion Buzzer for PoE NVR (New UI)
How to Set up Exception Buzzer for PoE NVR (New UI) 

1.Click  button to go to Device Settings>Channel Setting>Buzzer. If you want to enable/disable the alarm buzzer, please turn it on/off the Buzzer.
Please notice that this setting will apply to all the cameras connected to the NVR.

For more details, please refer to How to Enable/Disable Alarm Buzzer for POE NVR via Reolink App.

Channel Management

When a camera is successfully connected to the NVR, it will be distributed an IP address and a channel by the NVR for connection. Hence, with the NVR, you’re able to check the status of all the connected cameras at the same time. On the channel management page, you’re able to check the status of each channel/camera, delete the offline devices, arrange channel orders, etc.

Below are some basic instructions that you may refer to. 

On Monitor (Old UI)

1.Launch your Monitor of NVR, go to Menu>IP channel page. Then you will find the camera status in the sidebar of the IP channel page.

2.If you would like to delete the offline cameras, change the Channel of the disconnected IP camera to None and then click on Apply.

3.If you would like to change the display order of the camera, expand the selection bar to assign a channel for each camera. After that, click Apply to save the settings.

For more details, please refer to:
How to Check Camera Status on IP Channel page Via Reolink PoE NVR
How to Delete Offline Camera Information on IP Channel Page via Reolink NVR
How to Arrange the Display Order of Cameras on Reolink NVR 

On Monitor (New UI)

1.Launch your Monitor of NVR, then chooseMenu>Channel>Replace. You will find the camera status in the sidebar of the IP channel page.

2.If you would like to delete the offline camera, click on the offline camera and tap the Delete button to delete it from the NVR. Then the channel this camera was taken is free now.

For more details, please refer to the articles below:
How to Check Camera Status on IP Channel Page via Reolink PoE NVR(New UI) 
How to Delete Offline Camera Information on Channel Management Page via Reolink NVR(New UI) 
How to Arrange the Display Order of Cameras on Reolink NVR(New UI) 

.

Upgrade

As a centralized management system, RLN8-410 is able to upgrade both the NVR and the cameras that are connected to it. Below are some basic steps of upgrading for your reference. 

1.Unzip/extract the firmware file on your PC and transfer the PAK file to a USB, then insert the USB to the NVR USB port. 
Please notice that there are two USB ports on the NVR. One is at the front and the other one is at the back of the NVR. 

2.Log in to your Reolink PoE NVR on an NVR monitor, then go to Device Settings>System>Maintenance page.

3.Choose the correct firmware file and start to upgrade.
*If you only want to upgrade the firmware for the PoE NVR, you may click the Upgrade From USB and select the correct firmware file, then tap on the Upgrade button.
*If you need to upgrade the firmware for cameras that are connected to the PoE NVR, please choose Upgrade IPC From USB, then select the correct firmware for each channel and click on the Upgrade button to start upgrading.

For more details, please refer to How to Upgrade Firmware via PoE NVRs.
For upgrading the NVR only, you can also refer to How to Upgrade Firmware via Reolink Client (New Client).

1.Unzip the firmware file (.pak file) on your PC and transfer it to a USB, then insert the USB to the NVR USB port.

2.Log in to your Reolink PoE NVR on an NVR monitor, then go to Device Settings>System>Maintenance page.

3.Choose the correct firmware file and start to upgrade.

*If you only want to upgrade the firmware for the PoE NVR, you may click the Upgrade From USB and select the correct firmware file, then tap on the Upgrade button.
*If you need to upgrade the firmware for cameras that are connected to the PoE NVR, please choose Upgrade IPC From USB, then select the correct firmware for each channel and click on the Upgrade button to start upgrading.

For more details, please refer to How to Upgrade Firmware via PoE NVRs (New UI).
For upgrading the NVR only, you can also refer to How to Upgrade Firmware via Reolink Client (New Client).

.

<p>The post Reolink NVR Setup Guide first appeared on NVR IPCAMERA SECURITY.</p>

  Note: We’ve enhanced the design of the Blink app. If the steps listed in this article do not match your current app version, you can view the updated design.

This article will show you how to change the order of your Blink cameras in the Blink app. 

1.First, tap App Settings  on the bottom left of your Home screen.

2.Then tap Device and System Settings.

3.On the Device and System Settings screen, select the system you want to change under Systems.

On the System Settings screen tap All Devices.

From the Manage Devices screen, you can change the order that your Blink cameras appear in the app. To change the order, press and drag the three bars on the camera that you want to move. Place it in your desired location.

Once you change the order of your cameras, that order will display until you change it.

Return to the Home screen to see the new order of your cameras.

If you have additional mobile devices logged into the same Blink account, you will not see the new camera order on them. This is a per mobile device setting, which gives you the flexibility to view different camera orders on different mobile devices.

Using Your Blink Camera

Read More : Troubleshooting for Blink Mini Camera

Blink and iOS VoiceOver Screen Reader

Hear what your Blink camera sees

The iOS VoiceOver Screen Reader feature allows you to hear descriptions of Live Views and Motion Notifications in the Blink app. Once you enable the VoiceOver and Audio Descriptions options in your iOS device, you can hear descriptions of Live Views, Motion Notifications, or motion clips by tapping on the image in the Blink app.

Note

To ensure the VoiceOver Screen Reader works with the Blink app (version 6.15.0 or later), the iOS must be R15 or later. 

.

Examples of VoiceOver describing Motion Notifications in the Blink app

.

How to hear a VoiceOver Audio Description in the Blink app

• For a Live View description, tap the camera thumbnail to enter Live View. When Live View opens, the scene description is spoken from your iOS device.

• To hear a description of a Motion Clip, tap Clips  on the Blink home screen. Select a clip and the scene description is spoken from your iOS device.

.

iOS VoiceOver links

For instructions on enabling VoiceOver Recognition, visit Use VoiceOver Recognition on the web or in apps without accessibility information.

If you are not already familiar with using VoiceOver, learn about basic navigation and operation gestures.

What are Image Notifications?

Snapshot image from your Blink device

Image notifications send you a snapshot image of what’s happening in front of your Blink camera, so you can easily see activity without opening the Blink app. With a quick look at your notification, you can know immediately if you need to open up Live View to take a closer look, or wait and review your video later. Learn more about how to receive notifications of motion detection.

In order to view image notifications, your Early Notification camera setting must be disabled. Click to learn more about Early Notifications in the Blink app.

Note: Image notifications do not work with the Blink Video Doorbell. Since the Blink Video Doorbell always has Early Notification on by default, you will not be able to view image notifications on it.

If Local Storage is your only available method for saving clips, image notifications will not display since thumbnails are not generated in this case. Learn more about using Local Storage for saving clips.

iOS devices

Android devices

When you have motion alerts enabled on your iOS device, you will see a motion detection notification on your home screen. 

Tapping a notification on your home screen, will take you to the clip list in the Blink app with that saved clip.

When you “long press” on a notification, you will see a larger snapshot of your detected motion.

Image notifications also display when you are within the Blink app.

How to use Live View

  Note: We’ve enhanced the design of the Blink app. If the steps listed in this article do not match your current app version, you can view the updated design.

Use this article to understand how to access Live View from your Blink camera. Live View allows you to see your camera’s live video and hear sound directly from the Blink app and from certain Alexa enabled devices‍. 

Blink cameras use your Wi-Fi network to send Live View. The connection must have 2 MB per second or faster upload speed (from your camera to the Blink app). Live View can fail if the internet connection is too slow or external factors like signal strength and wireless interference.

How to access Live View

From the Blink app

To access Live View from the Blink app, tap the Live View play icon on the camera image you want to view.

From a motion notification

Available with certain cameras, Live Views can also be accessed by tapping the Motion Alert push notification sent to your mobile device. This setting must be enabled in the app in order for push notifications to be sent to your device. Learn more about Early Notifications.

If you do not see the Live View play icon for you Video Doorbell, your camera may be in Event Response mode. When this occurs, Live View is only accessible from the notification sent to your mobile device in response to a motion event. Learn more about Event Response.

Note: Even though a motion notification may appear simultaneously on multiple devices, Live View access is limited to one user at a time.

Live View additional options

To conserve bandwidth, your Live View may dim and a Continue? button appears at certain intervals. The button appears a few times until your viewing limit of five minutes is reached. Tap this button to continue watching the Live View.

Portrait orientation

When viewing the Blink app in portrait orientation (tall, not wide), the camera view fills the screen width. You can use the ‘pinch to zoom’ gesture to view image details; however, the actual image size does not change.

Tap the  icon in the top right of your Live View to switch to from portrait to landscape view. You can also turn your mobile device 90° sideways to automatically switch to landscape view.

Landscape orientation

Generally, the Blink app is viewed in landscape orientation (wide, not tall) and the images appear in full screen (as shown below). 

Tap the icon in the top right to switch back to portrait view. You can also turn your mobile device 90° vertically to automatically switch back to portrait view.

Save

Saving Live View clips is an exclusive feature of a Blink Subscription plan. Learn more about how to save Live View clips.

Audio Options

Speaker Icon
While in Live View, tap the speaker icon  to enable or disable the camera’s audio.

Two Way Audio
Cameras with a microphone and speaker display a microphone button  at the bottom. Two-Way Audio‍ is supported on the Video Doorbell, Outdoor and Indoor (Gen 3), Mini, and XT2 cameras.

Learn more about how to use two way audio with your camera’s microphone.

Note: The audio button name depends on your camera.

More Options

While in Live View, tap More for other options. Settings vary between devices.

Extended Live View

Extended Live View is only available in through the Blink Basic, Blink Plus and free trial subscription plans. 

This feature provides images and sound directly from a camera to the Blink app, up to 90 minutes at a time without user intervention. In addition, you can view regular Live View sessions up to five minutes without tapping on Continue.

Learn more about Extended Live View.

Device Settings
Device Settings can be accessed in two ways. One way is from the Blink app’s home screen through . The other way is by tapping the More button in Live View and then tapping . Learn more about how to access your camera’s device settings.

Wired Floodlight Camera: Siren On/Off

The siren can be turned on and off remotely through the app. This plays a loud alert noise through your Wired Floodlight camera’s internal speaker.

Learn more about using the Floodlight Siren.

How to leave Live View

When you’re ready to stop Live View, tap Close in the top left corner on iOS devices and < on Android devices.

Alexa enabled screen devices do not provide the Continue button and remain in Live View until the limit is reached. If the Live View ends before you are finished, you can re-enter Live View by pressing the icon again.

How to record Live View clips

To save Live View clips, you must have a Blink Subscription Plan or a free trial. Visit How to Save Live View clips to learn how to save Live View clips.

Two-way audio

Talking and hearing through your camera

The Blink Outdoor 4, Wired Floodlight, Video Doorbell, Outdoor and Indoor (3rd Gen), Mini, and XT2 cameras have two-way audio. Accessing the Blink app through your mobile device, you can speak and hear through the camera’s speaker and microphone.

Note: Two-way audio is not available in the XT and Indoor (1st Gen).

Confirm microphone access

Enabling your mobile device’s microphone

Before using two-way audio, check your mobile device to ensure the Blink app has permission to use the microphone.

iOS – See the If the microphone doesn’t work in a specific app article for instructions on enabling your mobile device’s microphone.

Android – See the Use your camera & microphone article for instructions on how to enable your mobile device’s microphone.

What if I don’t see the Blink app listed on my mobile device Microphone Permissions list? 

.

Two-way audio in the Blink app

Indoor and Outdoor (3rd Gen), Mini, and XT2

Note: Two-way audio is not available in the XT and Indoor (1st Gen).

1.Tap Live View for any of your eligible cameras.

2.At the bottom of Live View is the Hold To Talk button.

3.Press and hold this button while you speak. 

◦ A small animation appears above the button indicating your mobile device’s microphone is active and that your audio will be played through your camera’s speaker.

◦ Release the button when you are finished talking and the microphone will mute itself automatically. The audio can be heard through the camera’s speaker on the other end.

4.After 5 minutes, your Live View will stop and you must return to the Home screen to start another Live View session.

Note: With a Blink Subscription Plan or trial, you can use Extended Live View on the Mini camera. Extended Live View provides up to 90 continuous minutes of viewing.

Outdoor 4, Wired Floodlight Camera and Video Doorbell

1.Tap Live View for any of your eligible cameras.

2.While you’re in Live View, press the Tap to unmute button. The button will turn blue. 

◦ A small animation appears above the button indicating your mobile device’s microphone is active and that your audio will be played through your camera’s speaker.

3.When you’re finished talking, press Tap to mute.

4.After five minutes, your Live View will stop and you must return to the Home screen to start another Live View session. 

Note: With a Blink Subscription Plan or trial, you can use Extended Live View on the Wired Floodlight Camera. Extended Live View provides up to 90 continuous minutes of viewing.

Troubleshooting audio noise

Echo, feedback, or sudden repeated squeal noises

When the camera picks up sounds coming from the Blink app and transmits them back to the Blink app, “feedback” is created. Feedback is a repeating sound that increases in pitch and volume. It can occur when you have the Live View of a camera open in the Blink app and you are within hearing range of the camera.

• To avoid feedback, ensure that your mobile device accessing the Blink app is at least 10 feet away from your Blink camera. 

• To stop existing feedback or unwanted noise, tap the Mute  icon to silence the camera’s speaker. You can also stop the Live View session or switch out of the Blink app entirely.

Chirping, digital noise, or robotic sounds

Blink cameras convert audio into a digital stream so it can be heard for Live Views and recorded clips. During this conversion, extra sounds can sometimes be heard. These sounds may sound like a cluster of noises, scrambled distortion, chirps, or clicks when accessing a Live View or playing back a recorded clip.

The upload speed of your network plays an important part of your digital stream. When network speeds change quickly, your audio may be distorted. Blink devices require at least 2 Mb per second of available upload speed for each Blink device, even when multiple users are online.

Placement of your Blink devices

Device placement recommendations

Placing your camera near hard surfaces may produce unwanted sounds. Because a hard surface reflects sound, the camera microphone may pick up both the original sound and the reflected sound.

Placing the camera on an enclosed shelf or wall, or set back from a table’s edge near or between other objects may create a boxed-in environment that can affect the audio quality of the camera’s microphone and speaker.

For ideal placement, avoid placing your cameras near dense materials like brick, stone, concrete, or metals. Also, avoid placement near other electronic devices and confined spaces.

Setting your camera name and thumbnail

  Note: We’ve enhanced the design of the Blink app. If the steps listed in this article do not match your current app version, you can view the updated design.

When a camera is first installed, its serial number (DSN) is the default camera name, and the thumbnail image will be gray. If you want to change the name of your camera or add a thumbnail picture, follow the steps below.

Change the camera name

From the Home screen, tap the camera name to change it, enter the new name, then tap OK to save.

.

Generate a thumbnail

From the Home Screen, tap the thumbnail button . The camera will take a screenshot of what is currently in view and replace the gray with this screenshot. 

The thumbnail remains the same until you refresh it with this button. Learn more about using the Blink app.
 

Device Settings

  Note: We’ve enhanced the design of the Blink app. If the steps listed in this article do not match your current app version, you can view the updated design.

Info

Please update your Blink app if your settings appear differently than shown below. To learn more about updating, visit Current Blink App Versions.

This article describes the Device Settings in the Blink app.

Device Settings is found by tapping the icon  in the top right corner of each thumbnail image on the home screen.

The following settings are accessible by tapping on each menu option.

 General Settings

Last Updated
Tap Pull to Refresh to manually update your camera status.

Name
Camera name that will be displayed on your Home screen. You can edit this name at any time from here or at the Home screen.

Battery Level
This will indicate if your batteries are OK or need to be replaced.

Firmware
Displays your current firmware version.

Status LED
You can set when the LED light displays either as Off or Recording.

Change Wi-Fi  
Use this option if you need to connect your Mini or Wired Floodlight camera to a different router or reconnect your camera to your existing router to troubleshoot an issue.

Connection to Wi-Fi
Displays the Signal Strength from the last time the camera connected. After moving your camera it is a good idea to return here and ensure you have good signal strength.

Connection to Sync Module
Displays the most recent Signal Strength measurement. After moving any part of your system, it is a good idea to visit this settings page to ensure you have good signal strength. If not, move the camera closer to the Sync Module or the Wi-Fi router.

Temperature
The current temperature of that camera. Tap on the temperature to enable temperature alerts or to calibrate the thermometer.

Delete Device
This option removes the camera from your Blink system and it will no longer appear on the home screen.

 Motion Settings

Motion Detection
This setting must be on for the camera to detect motion. If this setting is off, the camera will not detect motion. Note: Once you enable motion detection, arm your camera to receive Motion Detection notifications and to save motion clips.

Motion Recording Types
For Outdoor 4 and Wired Floodlight cameras, select whether you want to see video for all motion, people only, or have them suppressed so no recordings are saved. Note: The Person Detection feature is only available when you have a Blink Subscription plan.

Motion Sensitivity
Controls motion sensor sensitivity. Low sensitivity detects larger objects in motion. High sensitivity detects smaller objects. Adjust sensitivity then test by creating motion notifications to achieve the right balance for your needs.

Motion Zones
Disables motion detection for selected regions of the camera view to prevent unwanted motion clips or notifications.

Retrigger Time
The length of time from the completion of one motion clip to the start of another. This can be set from 10-60 seconds.

Early Notification
This option sends the notification as soon as motion is detected and before the clip is complete. In the Blink App, tap the notification to be immediately taken to the Live View of that camera.

 Video and Photo Settings

Motion Clip Length
The length of motion clips to be recorded and this can be set between 5 and 60 seconds. Mini and Doorbell cameras record clips up to 30 seconds.

Video Quality
This allows you to change the video quality of your Blink camera. More information about the different modes can be found here.

End Clip Early If Motion Stops
If the camera stops detecting motion, the clip will end before the full clip length is reached.

Flip Video
This should be enabled when mounting a Mini camera upside down on a ceiling so that the image is rotated right side up.

Night Vision
If set to Off, the illuminator will not turn on. If set to On, the illuminator will always turn on. If set to Auto, the illuminator will only turn on in low light conditions.

IR Intensity
This value controls brightness of the IR illuminator. This value can be set to Low, Medium, or High. Adjust to control glare or show more detail.

Illuminator Intensity
Adjusts the brightness of the LED on the Indoor (1st Gen) camera.

Photo Capture
If Photo Capture is enabled, a photo is taken once per hour. If motion notifications or other events happen (or not), the images are assembled at the end of the day into a photo-animation in the Clip Roll. 

Note: Photo Capture only works with Indoor and Outdoor (3rd Gen) and Blink Video Doorbell cameras when you have an active Blink Subscription Plan. Learn more about Photo Capture.

 Audio Settings

Speaker Volume
A slider sets the speaker audio level on the camera, as well as the chime loudness of your Video Doorbell.

Ringer Volume
Controls how loud the Blink chime sound plays when you press your Video Doorbell button when it’s wired.

 Floodlight Settings

Wired Floodlight Settings:

Light Brightness 
This slider sets the lights’ brightness from a scale of 1-10. The default setting is 5.

Dusk to Dawn
Turn on this setting to automatically switch your floodlights on at dusk and off at dawn, based on the amount of light the camera senses.

Timeout after Manual Activation
Select the amount of time the lights will stay on after they are manually turned on. The default is 5 minutes and you can set the lights to stay on for 30 seconds or up to 15 minutes. You also have an initial option Until I turn off, which requires you to manually turn off the lights.

Motion Activation
When enabled, the lights will turn on if motion is detected. The lights will turn on regardless of whether your system is armed or not.

Motion Activation when armed: When enabled, the lights will turn on if motion is detected and the camera will record a motion clip.
Motion Activation when disarmed: When enabled, the lights will turn on if motion is detected, even if your system is disarmed. No clips will be saved.

Learn more about arming and disarming your Blink system.

Timeout after Motion Activation
Select the amount of time the lights will stay on after motion is detected. The default is 30 seconds and you can set the lights to stay on for 30 seconds or up to 15 minutes.

.

Floodlight Mount Settings:

Battery Level
Displays the battery charge percentage for the floodlight.

Light Brightness
This slider sets the LED brightness from a scale of 1-10. The default setting is 5.

Timeout after Motion Activation
This setting controls how long the LEDs remain lit after the detected motion stops. You can chose between 15 seconds or up to 5 minutes after activation. 15 seconds is the default.

Note: When battery powered floodlights are manually turned on they will stay lit up to one minute.

Daylight Mode
When enabled, the LEDs will activate when motion is detected during certain daylight hours, when the outside light is limited like at dusk and dawn. The LEDs will not activate when there is an abundance of outdoor light, often during midday hours.

Daylight Sensitivity
This setting only appears when “Daylight Mode” is enabled and controls the sensitivity of the lights during daylight hours. Lower setting values only activate the LEDs in darker conditions and higher values will activate the LEDs in brighter conditions.

Firmware
This displays your current firmware version which may be automatically updated at certain intervals.

Pan Tilt Settings

Firmware
View your current firmware version.

Calibrate Pan-Tilt Mount
Select this option to perform a manual calibration. Learn more about how to calibrate your Mini Pan-Tilt mount.

Doorbell and Chime Settings

Chime settings when Doorbell isn’t wired:

Use Blink Mini Camera as Chime
Opens the Mini camera selector. All Mini cameras on the system will be displayed. Learn more about using the Mini camera as a chime.

Mount with wiring
Full instructions for mounting with wiring.

Mount without wiring
Full instructions for mounting without wiring.

.

Additional settings when Doorbell is wired:

Chime Type
Select the chime type you use such as Mechanical, Digital or Mini.

Chime Power
Allows you to adjust the power of your chime.

Learn more about setting up your Blink Video Doorbell.

Privacy Settings

Privacy Zones
Disables motion detection for selected regions of the camera view to prevent unwanted motion clips or notifications.

Video Recording
When this setting is off, the camera will only send motion notifications without recording clips; however, Live View is still available.

Audio Streaming
Turn this setting off to disable the audio features of your camera.

Can I Disable the Blue Recording LED on the Camera?

Blink cameras have an activity indicator in the form of a blue color LED light on the front of the camera.

For the Blink Indoor, Outdoor and Mini, the Status LED is controlled in camera settings.

Blink XT and XT2, have a physical hardware switch inside the camera to control whether the status light is on or off.

The Blink Video Doorbell and 1st generation Indoor cameras are not adjustable.
.

Blink Indoor and Outdoor blue recording status LED setting

For the Blink Indoor and Outdoor cameras, there is a switch in the Blink app camera settings screen, named Status LED. The Status LED can be set to the following:

.

Blink Mini blue recording status LED setting

For the Blink Mini camera there is a switch in the Blink app on the camera settings, General Settings screen named Status LED. The Status LED can be set to the following:

XT and XT2 blue recording status LED switch

The XT and XT2 cameras have a hardware switch inside the battery compartment  to control the blue recording light.  This feature is not available on the Blink indoor cameras.

This article will show you how to turn off the blue recording LED on Blink XT. This LED is enabled by default from the factory.

1. Remove the battery cover. To see how to do that, click here.
2. To the right of your camera’s serial number, you’ll see a switch that says “REC. LED” with two positions, “ON” and “OFF”.

3. Using tweezers or a similar tool, slide that switch to the off position (toward the top of the camera).

.

Blink Video Doorbell blue recording status LED

The Blink Video Doorbell has a blue LED that flashes when the doorbell button is pressed. There is no setting to change this.

.

Blink 1st generation Indoor camera blue recording status LED

The first generation of Blink indoor camera does not have a setting to control the blue LED.

.

For more details, please visit the article New Device Layout Settings.

How Do I Use Scheduled Arming?

Set a schedule for automatically arming and disarming your Blink system

This article describes how to set an automatic schedule to Arm and Disarm your Blink system.

Create a schedule

1.To get started, open up the Blink app and tap Settings in the bottom right of the home screen and select Device and System Settings.

2.Next, select the system you want to schedule.
A system is a compilation of one or more cameras. When multiple cameras are added to the same system, they are linked together so that when you arm your system, all of the cameras in that system will arm at the same time.

3.To ensure that your system arms and disarms at the correct times, make sure your time zone is set correctly.

4.Next, tap Scheduling.

5.On the Weekly Schedule screen, create your schedule. Tap  in the top right of the screen.

6.By default, Arm will be enabled and the toggle on the right will be set to AM.

7.Schedule Arming: First, set the time and day you want to set your schedule arming. Drag the clock hands to your desired time. Time is changed in 15 minute increments. Select the desired days located at the bottom of the screen. When you’re done, tap Save to set the scheduled arming and you are taken back to the Weekly Schedule screen.

8.Schedule Disarming: Next, set the time and day you want to set your schedule disarming. In the example below, the week schedule is highlighted in blue because the the disarm time has not been set. Tap the  again to set disarm schedule.

9.Disarm scheduling is done in the same manner, but you will want to switch the toggle on the left to Disarm. Drag the clock’s hand to your desired disarm time and select the days of week again. Once you have your disarm schedule set to your desired time, tap the Save button again.

10.Your schedule is now set.

.

After your schedule is set

Modify existing schedule

You can modify saved schedules by tapping on the arm and disarm toggles and setting new days or times.

Disable Switch

If you want to temporarily disable your schedule (Example: You’re going on vacation), you’ll now see a disabled toggle on Scheduling in the System Settings menu. Enabling this switch this will disable your schedule until you turn it off.

Delete schedule

1.To delete your schedule, go back into your schedule view. Tap the trash can icon  to delete the schedule.

2.You’ll be asked to confirm. Tap Yes.

Note: Scheduled arming and disarming of your system will override any manually set or IFTTT or Alexa triggered arm and disarm settings. 

In order to record motion events, you must have motion detection enabled for a specific device by tapping on the Running Man icon from the home screen or enabling motion detection in the device’s setting screen. Learn more about understanding motion detection.

Deleting a System

Use this article to understand how to delete a system.

System basics

Blink devices work together as part of a system. Each system can manage up to ten Blink devices.

When you delete a system, all of its devices are deleted, and an email is sent to the account owner. Use this to quickly remove items from your account, for situations such as selling a device or replacing an existing device.

Deleting a system will not delete any previously saved clips within your storage location.

To delete a system

1.From the Home screen, tap Settings  to view system settings.

2.Tap Device and System Settings.

3.Tap the name of the system you wish to delete.

4.From the System screen, tap Delete System, and then tap DELETE in the confirmation popup.

After confirming, you are returned to the Settings screen and the system has been removed.

.

Empty system

Empty systems contain no devices and is ready to either have devices added to it or be deleted.

If you delete all devices from a system, or have an incomplete setup after creating a system name, it is found in App Settings > Device and System Settings.

App settings

App settings

  Note: We’ve enhanced the design of the Blink app. If the steps listed in this article do not match your current app version, you can view the updated design.

This article describes the app settings found on the Settings screen.

Home screen

The home screen has three icons at the bottom of the screen:

 Home – Tap this to bring you back to the home screen where your cameras are accessible.
.

 Clips – Tap this to view the Clip List where all of your Live Views and Motion Clips are saved. Learn more about how to view motion clips in the app.
.

 Settings – Tap this to see the Settings screen, which contains all of your Account, Subscription Plan and System settings. All of your account settings are found on the Account and Privacy screen.

App settings

Tap the Settings icon on the home screen to display the Settings screen.

 Account and Privacy

Account settings, link to Amazon, Alexa, Neighbors and privacy preferences.

.

Email
This is the email account used when creating your account. You can change your email by tapping on this item and following the prompts.

Password
Use this option to modify your account password. Learn more about how to modify your password.

Require Face ID
This feature helps to keep unrecognized people from accessing your camera systems.

Phone Number
This displays the phone number associated with your account for verification purposes and can be modified. Learn more about how to change your phone number.

Country
This option helps us personalize your experience when you select the country you live in, by ensuring you receive the right messages based on your location.

Link to Amazon Account
Use this option before you purchase a subscription plan, in order to link your Blink and Amazon accounts. Once your accounts are linked it will display as Amazon Account Linked. Learn more about linking your Blink and Amazon accounts.

Link to Alexa
Use this option to directly open your Alexa app in order to enable voice alerts and voice control for your devices. Learn more about Alexa.

Neighbors App
The Ring neighbors program and mobile app is available to customers. The app and more information can be accessed from https://ring.com/neighbors.

Manage Mobile Devices
To ensure only authorized people can access a Blink account, the account owner can view and control all additional devices that access their account within the Blink app.

Enable Crash Reporting
If the Blink app suddenly stops working, use this toggle to control the sending of crash reports.

Grant Blink Support Account Access
Enable this toggle to give the support team access to your account for up to 14 days. Learn more about granting access to your Blink account.

Sign Out
Use this option to sign out of your Blink account.

Delete Account
Tap this button to delete your account. If you delete your Blink account, you lose access to clips that are stored on our systems, as well as access to any Blink devices through the Blink app. Learn more about how to delete your account.

Blink Plans

View and manage your Blink plans

.

Trial Information
If you are within a Blink subscription trial period, you will see the trial end date as well as an option to cancel your trial. Learn more about Blink subscription plans.

Learn about Blink Plans
Select this to view a comparison of Blink subscription plans.

Link to Amazon Account
Use this option before you purchase a subscription plan, in order to link your Blink and Amazon accounts. This will not appear if your accounts are already linked.

Note: If you are not subscribed to one of our subscription plans or on a trial, you may not see the Blink Plans option under your Blink app settings screen.

Device and System Settings

Create schedule, organize camera displays and other system settings

.

Systems
All of your systems in your account are listed here. When you tap on a system, you will be taken to the System Settings screen. 

Here you can rename your system, sort your cameras as they appear on the home screen, set scheduling, time zone, access your Sync Module settings and enable Save all Live Views. You also have an option to delete your system if necessary.

Temperature Units
Select this option to set your temperature units to display as either Fahrenheit or Celsius, which appears in your camera settings page.

Notifications

Customize notification preferences

.

The Blink app provides notifications to alert you about events that occur in your account and systems.

Events are as follows:

Alerts are as follows:

<p>The post Using Your Blink Camera first appeared on NVR IPCAMERA SECURITY.</p>

Getting Started: Setting Up User Privileges

The VORTEX Portal provides a structured hierarchy of user roles to ensure smooth management while maintaining high security. This article will guide you through understanding and setting up the four roles: Owner, Admin, Supervisor, and Viewer.

Who Sees What

Below is a table that explains in detail each role and their associated features:

Vivotek Vortex Camera Ultimate Guide

Read More : iViewer installation and user guide

How to set up privileges for a user

Step 1: Go to the Users page.

Step 2: Click on a user’s name or profile to enter their detail page.

Step 3: Locate and click the “Access settings” button on the top-right.

Step 4: Assign the appropriate device groups for permission.

Step 5: Once you’ve made the necessary changes, click “Save” to finalize the settings.

.

Getting Started: Setting up your VORTEX account

To access the VORTEX system, please proceed the following steps to set up your VORTEX account.

Step 1. Scan the QR code below to download the VORTEX app.

Step 2. Open the application in your mobile device and click on the “Create account” button to create a VORTEX account.

Step 3. Type your email to be use to access the system and set a password.

Enter an email address and a password. The password should contain 8 to 64 alphanumeric characters, including at least one uppercase letter, one lowercase letter, and one numeric character. Spaces are not allowed. When finished click on the “Create account” button. 

The application will send an email to the configured address so that you can activate your account. 

Step 4. Access your email and look for a “Welcome to VIVOTEK Vortex” email. If you cannot find it, you can search it by using the mail filter “no-reply@verificationemail.com”. Then, click on the “Verify Email” to activate your account. 

Once the account is activated, you will see the following message in the browser:

Step 5. Go back to the application and login into the system by using your email and password.

Congratulations! You now are able to access the VORTEX service in your phone!

Getting Started: Adding your VORTEX camera to your VORTEX account

VORTEX cameras are very easy to configure. Here is a detailed step-by-step guide that will teach you how to add the device: 

Step 1. In your mobile device, run the VORTEX application. 

Step 2. Access the VORTEX service using your email and password. 

Step 3. Click on your account icon to open the application menu. 

Step 4. Click on “+ Add devices” button to start adding your device.

The application will open the camera feature (be sure to enable the respective permissions). Then, scan the QR code located either on the package box or on the camera itself.

If the scan is successful, you will first see the camera’s general information. Be sure that the information displayed is correct. 

Step 5. Click on the “Add” button to add the device to your account. Once added you will see the following message:

If you want to keep adding devices, click on the “Add another device” button and repeat the same process. 

Step 6. Check that the device is visible in the application. 

You can also go to the VORTEX Portal and check that the camera was added to the system properly. 

<p>The post Vivotek Vortex Camera Ultimate Guide first appeared on NVR IPCAMERA SECURITY.</p>

The Avigilon AI NVR is a network security appliance that provides all of the functionality of an Avigilon Network Video Recorder with: