With concise and fashion GUI, it supports multiple and real-time previews, QR scan, PTZ control, video capture, and recording backup. More functions are waiting for you.

Tips: Play H265 encoded format video in APP personal center album, you need iOS11 or above to support.

EseeCloud(IP Pro, VR Cam)– Remote view for 24 hours in Mobile APP.

With concise and fashion GUI, support multiple and real- time preview, QR scan, PTZ control, video capture, recording backup. More functions are waiting for you.

Tips: User manual and more software (including CMS), please go to https://eseecloud.app/download/ to download.

Fast Networking

Step:

EseeCloud Nvr User Manual

IPC Set Up

Step:

Video Detection Setup

Step 1: Enable Motion Detection

Step 2: Configure Record Plan

Video Playback

Steps:

Playback Controls:

.

Video Backup

Steps:

Tips: Supports up to 32GB USB disk backup. Each recording file is packed every one hour for backup.

Access In LAN

Step 1: Network Configuration

Step 2: Connect Within LAN

Step 3: Viewing the Video

Tips: Ensure that the video recorder and computer are on the same network segment for proper connectivity.

Access In WAN

Step 1: Device Identification

Step 2: WAN Access

Step 3: Video Access

Tips: Video quality and fluency depend on the upload speed of the video recorder and download speed of the computer. Each channel requires at least 30KB/s.

Mobile Application Download and Installation

Esee Mobile Application (IP PRO) – Add Device

Step 1: Register
Step 2: Enter the device interface
Step 3: Add the device
Step 4: Added successfully. Click channel No. to get video
Step 5: Remote playback

VR-NVR USER MANUAL

Fast network

Step: Right-click the mouse in the main menu → Fast network → Choose Auto Config → Click OK. If you want to manually configure the IP address, click diagnose. If it shows a healthy network, it indicates the connection to the Internet is good. If there is a network anomaly, plz process according to the clew. (Ensure your device has accessed the network)

IPC Set UP

Preview of VR Camera

Double-click the image on the main interface—choose a different preview mode.

Video detection

Step 1: Right click mouse in main menu→System setup→Record setup→Record plan→choose motion→choose all→click Copy to→click OK to save setting

Step 2: Right click mouse in main menu→System setup→Channel setup→choose Video detection→choose motion→click Enable→Click OK

Video Playback

Step: Right click on main interface→video playback→choose “channel”→choose “record mode”→setup “search time”→click “search”, click timeline to choose time→click “playback” to check recording file.

Video Backup

Steps: Right-click the mouse in the main menu→Video backup→choose channel No.→choose Record mode→In search time, input beginning time and end time→click search, and recording will come out→choose the video which needs to be backup→click video backup.

Tips: Support 32G U disk backup maximum, recording file will be packed every one hour.

Access in LAN

Step 1: Quick Networking—check the IP address of the device.

Step 2: The correct web port needs to be put in the web port is changed, such as the web port changed to 1111, then input http://192.168.1.247:1111

Step3: Once access successful, you can get the video

Tips: Please make sure the video recorder and computer are in the same network segment.

Access in WAN

Step1: Right-click the mouse in the main menu—Quick Networking—check the ID of the device.

Step 2:

Input http://www.dvr163.com on IE browser, input ID, user name, and password, and click log in.

Step 3:

Once you access it successfully, you can get the video.

Tips:

Video quality and fluency depend on the upload speed of the video recorder and the download speed of the computer; each channel needs above 30KB.

Mobile application download and installation

No. 1: Go to http://www.dvr163.com/download/indexm.php?p=ippro in a mobile browser, enter the download page, click install to download, and install the APP.

No.2: Please scan the QR code in the manual to download the APP.

Esee mobile application (IP Pro)-Add device

<p>The post EseeCloud Nvr User Manual first appeared on NVR IPCAMERA SECURITY.</p>

How to add a Hikvision NVR to Hik-Connect

Before you start…​

Part 1: Enable Hik-Connect on the NVR…​

.

.

.

.

Part 2: Set up Hik-Connect on your mobile phone or tablet…​

.

.

.

Part 3: Add the NVR to your Hik-Connect account…​

.

.

.

Other tips…​

Guides for Hikvision NVRs with V5 firmware

How to set up motion detection and alerts on a Hikvision NVR

What is Motion Detection and why is it useful?​

Motion detection is one of the easiest events to set up and will notify you as soon as a person or vehicle enters a predefined detection zone in your scene. Traditionally, it would just rely on lots of pixels changing between frames in your camera’s video stream, which would indicate movement in the scene.

Of course, this would cause lots of alerts for things you are not interested in, such as animals, moving plants and rain. Hikvision’s Acusense cameras and NVRs now have something called Motion Detection 2.0, which cuts the false-positive detections right down as will only notify you when people and/or vehicles are in the scene by learning what they look like. In this simple step-by-step guide, we will show you how to get motion detection set up on the new NVR 5.0 web interface.

Step 1: Go to your NVR’s Motion Detection configuration page…​

Step 2: Configure your Motion Detection zone and rules…​

​

Quick tip…​

If you find that the camera preview is too small when drawing your detection zones, you can switch the view to full screen by clicking on the Full screen (four arrows) button in the toolbar, and then exit full screen by pressing Esc on your keyboard.​

Step 3: Set the arming schedule to specify when you want Motion Detection active…​

​

Quick tip…​

If the 30-minute segments are not precise enough for you, you can finely tune a period of arming or disarming by double-clicking on the segments and specifying your start and end times in minutes using the arrows.​

​

Step 4: Set what you need the NVR to do when a camera detects a target…​

How to connect an IP camera to a Hikvision NVR

Adding cameras to your Network Video Recorder (NVR) is a crucial step in any CCTV setup. Not only does it allow you to store and access all your camera recordings in one place, but it also simplifies camera configuration. In this simple step-by-step guide, we’ll show you how to add cameras to a Hikvision NVR using the new NVR 5 web interface.

.

Why add cameras to an NVR?​

.

Before you start…​

Before anything, to be able to add your IP cameras, you need to make sure that:
.

.

How to add your cameras using the V5 GUI…​

Step 1:​

Open a web browser and enter the IP address of your NVR in the address bar. If you are not sure what this is, use the SADP tool to find it.​

Step 2:​

Log in to the NVR using the “admin” username and password you have set on it.​

​

Step 3:​

Go to: Device Access > Device Configuration > PoE Settings​

​

If you are connecting your camera via the Plug-and-Play method, then make sure that Network Camera Plug-and-Play is enabled on the POE port you will be connecting the camera to on this page.​

​

For any camera with a cable run under 100m, leave the Network Cable Distance as Short Distance.​

​

If you are connecting your camera manually by IP address, disable the Network Camera Plug-and-Play option for the channel that you plan to add the camera to.​

Step 4:​

Go to: Device Access > Device > Video Device​

​

For any Plug-and-Play camera, just make sure that it is in its inactive default state and then connect it to the port you reserved in step 3. After 20 seconds or so, the camera Status should turn to Connecting and then Online (you may need to click on Refresh to see this).​

​

For Manually added cameras, if you can see the camera in the List of Online Devices section, then just tick the box for the camera and then click + Add to Device List, which will then automatically add it to one of the channels you disabled Plug-and-Play on in the last step.​

Alternatively…​

Click on +Add at the top of the page and fill out the fields as follows:​

​

IP Address: Enter the IP address of your camera, using the ‘Test’ button to verify there is a camera at that address. ​

Device Name: This can be anything you like, as it is the name the camera will show with on your NVR. ​

Protocol: Select the camera’s manufacturer from this list, or failing that, use the ONVIF protocol (your camera will need to have ONVIF enabled for this to work). ​

Management Port: Enter the Server port set on the camera, which you can find in the SADP tool or in Network>Basic Settings>Port in the camera’s web browser interface. If you haven’t changed this, it is usually 8000 by default. ​

User Name: “admin” or the username of any other users set up on that camera. ​

Password: The password set with that user on the camera – if this is the same as the ‘Default Activation Password‘ you have set on the NVR, then you can tick this box instead. ​

Transfer Protocol: ‘Auto’ is normally best. ​

​

When these are completed, click OK.​

​

Your camera should then appear in the list of devices with an assigned channel, and an Online status, meaning it has been successfully added.​

.

Extra tips…​

Source : https://www.use-ip.co.uk/forum/forums/guides-for-nvrs-with-v5-firmware.71/

.

<p>The post Guides for Hikvision NVRs with V5 firmware first appeared on NVR IPCAMERA SECURITY.</p>

I spent the last two weeks getting to know everything about these cameras and this thread will capture all this information. It will take me several weeks to document all the information so please be patient.

There are a variety of problems that I will try my best to explain and share the possible solutions. I have gotten pretty comfortable with these cameras and have purposely bricked them to various degrees of severity just to validate the recovery process. Most people “brick” their cameras trying to upgrade the firmware. This is not a serious issue and it can be corrected very easily. The camera runs an upgrade service on port 3800. The configTool always shows a default port of 37777 but this is not an issue as it can do the upgrade on port 3800 anyway. Change your port to 3800 and use a firmware file lsted below and you are back in business.

I will keep updating this post as I get more time to write all the details around recovery. I will also post links to over 40+ firmware files that and which cameras they will work with. It will take me a bit of time to capture all this information, so please be patient.

 How to Download and Prepare Firmware

This guide will show how to download and prepare the firmware file for a Dahua device.

Firmware files for Dahua devices can be found at Firmware by Device or the specific product page for the device

Firmware is typical provided in a ZIP file, a compressed file format

This file will contain the actual firmware file, which needs to be extracted from the ZIP file in preparation for the upgrade

Prerequisites

Video Instructions

Step by Step Instructions

Confirm the Model and current firmware of Dahua device

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Info

3. Click Version

The Device Type will be displayed

The current System Version will be displayed

Download the firmware file for device from DahuaWiki

4. In a browser go to DahuaWiki.com

Under Specifications, Firmware, & Manuals

Click the device type (in this example Recorder)

5. Enter the device model into the field

6. The results will be filtered

7. Click the firmware icon to download the firmware file

8. The file will download

Extract the firmware file to local computer

9. Right click the Start Menu / Windows icon in the bottom left of the screen

Select File Explorer

10. Select Desktop

11. Click Home

Then click New folder to create a new folder to extract the contents of the firmware zip file

12. Find the created folder in the list, double click to open

13. Under the Downloads window of the browser, click ‘Show in folder’

A new File Explorer window should open containing the directory the firmware zip was downloaded to

Locate the file in the list

14. Right click

Select Cut

15. Select the window with the new directory

Right click in the window

Select Paste

The folder will appear in the directory

16. Right click the file

17. The contents of the zip file will appear in a new window

18. Click to select all files in the folder

Drag and drop the files to the created folder

The files will appear in the directory

The firmware file will appear in the directory ready to use

Unbricking your Dahua IP camera (Tips, Tricks & Firmware)

BRICKED CAMERA? How can you tell?

There are several types of “BRICKED” camera conditions and they have varying levels of severity and also varying levels of complexity for recovery. Most are simple and caused by bad firmware uploads. The worst will require a full rebuild of the partitions which load the kernel, software and all other data.

1. The first step in identifying the severity of your issue is to determine what still working on your camera. In order to do that, lets remove as many variables as possible to the troubleshooting process. If possible, connect the camera ethernet and PC ethernet on it’s own switch and make sure that no vlan tagging is enabled on the switch.

Next, you need to figure out if the IP address is still reacheable. Ping the last known ip address. The default address for most cameras is 192.168.1.108.

If you don’t know it you can use the arp/ping method to configure which adds as startic arp entry to a new ip address. (This feature is enabled on the camera by default)

2. Once you have a pingable IP, you need to know what services are still active on the camera. This can be done with a simple port scanner. I have added a link to below in tools.

3. Run the port scanner and record which ports are still open. In many cases port 23 and port 3800 will still be open. If this is your situation, it is a very simple fix. If no ports are open, you will need to do a full image load which is more complex.

The typical ports that you would see are:

23 – Telnet access

80 – Web User interface

443 – SSL

554 – Real time streaming port

3800 – Upgrade Deamon

5000 – UPnP

37777 – TCP Video streaming

37778 – UDP Video Streaming

42323 – Real time remote runner

Plus a whole bunch more of UDP ports and more TCP ports

REPAIR WITH PORT 3800

Download a step by step guide (DAHUA IP Camera Recovery v1.0.pdf) with screen prints @ http://tinyurl.com/lbl3up7

1A. If port 3800 is open you can connect with the Dahua Config tool (link below in tools). I tdefault to port 37777 but change it to 3800 as this port where the upgrade daemon is listening. Port 37777 is a redirect but it won’t work if your firmware has failed.

Launch the config tool and click on login button. Type the IP address , username and password then port 3800.

Open a know working firmware file and upload to the camera.

1B. If port 3800 is not open, go to the next step to enable port 3800.

2. If you have telnet access, you can login with putty. Link to putty below in tools. The default Web UI password is admin / admin.

In older firmware the telnet account is root / vizxv

In newer firmware the telnet account is admin / 7ujMko0+”web UI password” —> 7ujmko0admin

Once connected you can execute a ps command to see running processes. /usr/sbin/upgraded process is what listens on port 3800 for the firmware binary file.

There is also another copy in /var/tmp/

A useful tip for watching the upgrade process is to kill the “upgraded” process that is running and re-launch it in the foreground to watch the upgrade.

~#>ps

625 root 0:00 [mtdblock3]

630 root 0:00 [mtdblock4]

635 root 0:00 [mtdblock5]

772 root 0:00 [ubi_bgt7d]

776 root 0:00 [ubifs_bgt7_0]

790 root 0:00 /sbin/telnetd

798 root 0:00 [OSA_796_1]

860 root 0:00 syshelper elper 60

861 root 0:00 /usr/sbin/upgraded

869 root 0:00 [dsplogd]

870 root 0:00 [encode_guard]

889 root 0:00 [flush-ubifs_6_0]

923 root 3:29 ./VideoDaemon AEWB AF TVOUT

~#> kill -9 861

~#> /usr/sbin/upgraded

22:52:46|[crypt] crypt_open ok!

Name: upgraded, bulid date: Apr 19 2014 09:17:58, svn: 255

Fail to get env authcode!

@@@@ buf = PZC4MU056W00XXX

22:52:52|[pdc] WARN (MISC_ioctl|493): Get SdCard cfg failed !

UPGRADED_MSG: Can’t Open /mnt/mtd/Config/passwd

UPGRADED_MSG: Login success!

UPGRADED_MSG: Kill 976 successful

UPGRADED_MSG: reset_watchdog

UPGRADED_MSG: Receive A4(alarm)

UPGRADED_MSG: reset_watchdog

UPGRADED_MSG: Receive A1(alive package)

UPGRADED_MSG: reset_watchdog

UPGRADED_MSG: Received : 29868252, FileSize : 29868252

UPGRADED_MSG: Download Complete

UPGRADED_MSG: DoDownLoad success!

UPGRADED_MSG: Flash init success

UPGRADED_MSG: hwid file success!

Fail to get env native!

UPGRADED_ERR: LINE: 1074: invalid file: Install.lua

UPGRADED_MSG: zip file total size: 40900220

Fail to get env authcode!

@@@@ buf = PZC4MU056W00XXX

22:53:10|[pdc] WARN (MISC_ioctl|493): Get SdCard cfg failed !

UPGRADED_MSG: packet.name: SD6XXX, board.name: IPC-HFW4300S-V2

UPGRADED_MSG: packet.hardver: , board.hardver:

UPGRADED_MSG: packet.name: IPC-HX3XXX, board.name: IPC-HFW4300S-V2

UPGRADED_MSG: packet.hardver: , board.hardver:

UPGRADED_MSG: Verify version success

Header CRC Checking … OK

Image Name: kernel.img

Image Type: kernel.img (gzip compressed)

Data Size: 2546876 B, Bytes = 2.43 MB

Load Address: 0XC80000

Data CRC Checking … OK

Programing start at: 0XC80000

<5>UBIFS: un-mount UBI device 2, volume 0

<5>UBIFS: un-mount UBI device 4, volume 0

Upgrade : Complete Total 6%…

Header CRC Checking … OK

Image Name: partition-x.cramfs.img

Image Type: partition-x.cramfs.img (gzip compressed)

Data Size: 4160 B, Bytes = 0.00 MB

Load Address: 0X500000

Data CRC Checking … OK

Programing start at: 0X500000

Upgrade : Complete Total 6%…

Header CRC Checking … OK

Image Name: romfs-x.ubifs.img

Image Type: romfs-x.ubifs.img (gzip compressed)

Data Size: 7340096 B, Bytes = 7.00 MB

Load Address: 0X1200000

Data CRC Checking … OK

Programing start at: 0X1200000

Upgrade : Complete Total 24%…

Header CRC Checking … OK

Image Name: pd-x.ubifs.img

Image Type: pd-x.ubifs.img (gzip compressed)

Data Size: 1966144 B, Bytes = 1.88 MB

Load Address: 0X940000

Data CRC Checking … OK

Programing start at: 0X940000

Upgrade : Complete Total 28%…

Header CRC Checking … OK

Image Name: user-x.ubifs.img

Image Type: user-x.ubifs.img (gzip compressed)

Data Size: 21233728 B, Bytes = 20.25 MB

Load Address: 0X2200000

Data CRC Checking … OK

Programing start at: 0X2200000

Upgrade : Complete Total 80%…

Header CRC Checking … OK

Image Name: custom-x.ubifs.img

Image Type: custom-x.ubifs.img (gzip compressed)

Data Size: 1966144 B, Bytes = 1.88 MB

Load Address: 0X600000

Data CRC Checking … OK

Programing start at: 0X600000

Upgrade : Complete Total 85%…

Header CRC Checking … OK

Image Name: web-x.ubifs.img

Image Type: web-x.ubifs.img (gzip compressed)

Data Size: 5505088 B, Bytes = 5.25 MB

Load Address: 0X1A00000

Data CRC Checking … OK

Programing start at: 0X1A00000

Upgrade : Complete Total 99%… [libpdi] Read: blkIndex: 0,pageIndex: 1,byteIndex: 0 ,fLag: ff

Upgrade : Complete Total 100%… UPGRADED_MSG: will reboot system

Here you can see each partition being loaded wit the individual img files. I will write a quick how to on loading each one individually at a later time.

If you chose a valid firmware file, you will be back in working order. If you still have problems, repeat with another firmware file till you have a valid file. The IPC-HFW4300S-V2 is not natively compatible with all other 4300S firmware. I am in the process of writing a how to that explains how to over come this issue.

UNBRICK WITH UBOOT via SERIAL

NOTE: This section is coming soon… I’m gathering all the images I need for various camera types

OTHER USEFUL INFORMATION (to be sorted later)

The firmware consists of several images that are loaded into various partitions in flash in a UBI file system. You can load each partition separately if needed. More on this later…. (I’ll put a guide together on flashing and recovering partitions)

Once you telnet into the camera, there are number of useful binaries in the user shell that can help correct and diagnose some of the problems people are experiencing. One of the helpful steps is to kill the /var/tmp/upgraded process and run it in the foreground so you can see what is going on and easily capture error messaged. The /var/tmp/upgraded process is what opens the port 3800 and allows you to connect to the camera with the config tool if your web services have failed. There is also another copy in usr/sbin/.

Also, in there is a command to reset all the parameters back to factory defaults (username, password, ip address back to 192.168.1.108 etc.) This can be accomplished with /sbin/clearparam.

Another issue that people run into is the constant reboot issue. This can be caused by a failed process. The main application which provides all the camera capabilities (web interface, streaming, etc.) is /usr/bin/sonia. This process is what makes most firmware different from version to version (sort of). There are also changes to the web partition which contains the web server pages that /usr/bin sonia hosts on port 80. The sonia process is invoked by a shell script in init.d and if the process is killed, the camera reboots after a few minutes. This has cause many people issues when trying to “unbrick” the camera since you only have a few minutes between reboots.

To stop the reboots you can update the flash. There is a parameter called appauto that tells the camera to auto start /us/bin/sonia. If you want the camera to start and not invoke the shell script that launches sonia, you need to set appauto to 0. This will stop the camera from rebooting when sonia is not running.

This cam be accomplished by running ‘/sbin/appauto 0’. To turn it back on, just run /sbin/appauto 1. This writes the boot parameter in flash that the kernel reads before starting the process. You can check the current status of the appauto bootparameter with ‘cat /proc/dahua/bootpara’ It will only show what the parameter was when you booted up, so if you changes it you need to reboot to see the change in /proc/dahua/bootpara.

Realtime streaming URL – rtsp://192.168.1.108/cam/realmonitor?channel=1&subtype=0&proto=Onvif

You can change the subtype to 1 for the secondary stream also you can add user:password@ in front of the IP address if you have the permissions set requiring it.

You can use the HTTP API to configure some parameters that are not yet in the web UI. For instance, another member discovered he could enable NFS through the web UI in addition to the local SD card. This config is not possible through the web interface as you need to pick one or the other.

These documents details the API of Dahua video products (links provided to some of the versions below). Programmers or users can access and configure Dahua video products through the API. Every setting of the camera is available through the API whereas only a small number are available through the WEB interface. The document with version 1.10 is available with firmware version 2.0 and above. This document with version 1.20, 1.21, 1.22, 1.23,1.24,1,25,1,26,1,27,1,28 is available with firmware 2.210 and above.This document with version 1. 29 ,1.30, 1.31, 1.32, 1.33, 1.34, 1.35,

1.36 is available with firmware 2.210 and above.This document with version 1.37 is available with firmware 2.212, 2.4 and above.

I have also done a bit of testing around the tftp process that is invoked in u-boot that looks for upgrade_info_7db780a713a4.txt and failed.txt. I think with a little more work, I’ll figure out if there is a recovery method using tftp without serial access. This would be necessary if you lose telnet access and need to rebuild the kernel partition that hosts telnetd.

Tools

DAHUA IP Camera Recovery v1.0.pdf………………….. http://tinyurl.com/lbl3up7

Port Scanner ………………………………………….. http://tinyurl.com/q53pojg

Putty …………………………………………………….. http://tinyurl.com/lvbbmsq

Tftp Server …………………………………………….. http://tinyurl.com/m46wnhe

Dahua Docs & Tools

DAHUA_HTTP_API 1.0 .pdf ………………………………………… http://tinyurl.com/lb43lga

DAHUA_HTTP_API_1.23.pdf ………………………………………… http://tinyurl.com/lrwye3k

DAHUA_HTTP_API_FOR_IPC 1.28.pdf …………………………………. http://tinyurl.com/kskrcay

DAHUA_HTTP_API_FOR_IPC&SD-V1.36.pdf ……………………………… http://tinyurl.com/mooccf9

DAHUA_HTTP_API_FOR_IPC&SD-V1.37.pdf ……………………………… http://tinyurl.com/kvyddfp

DAHUA_HTTP_API_FOR_DVR_V1.29.pdf ………………………………… http://tinyurl.com/klc72tr

General_ConfigTool_Eng_V1.0.5.R.120428.zip …………………… http://tinyurl.com/mwlzbb3

General_ConfigTool_Eng_V1.06.1.T.120807.zip …………………… http://tinyurl.com/leudphu

General_ConfigTool_Eng_V1.07.2.R.130304.zip ………………….. http://tinyurl.com/obs5ud7

General_ConfigTool_Eng_V1.07.3.R.130701.zip ………………….. http://tinyurl.com/o6p628f <—- Use this one

General_ConfigTool_Eng_V2.00.0.R.140410.zip …………………… http://tinyurl.com/nbqtgev

Firmware Files

Firmware files are grouped by camera type and video signal (NTSC –> Eng_N / PAL –> Eng_P / or BOTH –> Eng_NP)

Files are ordered by version number with the latest Firmware in blue.

Files with DH_ prefix are DAHUA direct firmware files and those with General_ prefix are general release for OEM cameras but I’ve had good luck with both.

DH_IPC-HX1100_Eng_NP_V2.210.0000.3.R.20140416.bin ………………………………………….. http://tinyurl.com/m2jf3qv

General_IPC-HX3(2)XXX_Eng_N_V2.210.0001.0.R.20130517.bin ……………………………………….. http://tinyurl.com/q98zg9x

General_IPC-HX3(2)XXX_Eng_P_V2.210.0001.0.R.20130517.bin ………………………………………… http://tinyurl.com/nekapn3

General_IPC-HX3(2)XXX_Eng_NP_V2.210.0001.0.R.20130517.bin ……………………………………… http://tinyurl.com/p59ym6z

General_IPC-HX3(2)XXX_Eng_P_V2.211.0000.0.R.20130726.bin ………………………………………… http://tinyurl.com/my54r9z

General_IPC-HX3(2)XXX_Eng_N_V2.212.0000.0.R.20131206.bin ……………………………………….. http://tinyurl.com/lrvtm2z

General_IPC-HX3(2)XXX_Eng_P_V2.212.0000.0.R.20131206.bin ………………………………………… http://tinyurl.com/n9rv23n

General_IPC-HX3(2)XXX_Eng_N_V2.212.0001.0.R.20131224.bin ……………………………………….. http://tinyurl.com/l5kg2d9

General_IPC-HX3(2)XXX_Eng_P_V2.212.0001.0.R.20131224.bin ………………………………………… http://tinyurl.com/q6c2gox

DH_IPC-HX3(2)XXX_Eng_NP_8M_V2.212.0000.4.R.20140307.bin ……………………………………….. http://tinyurl.com/mnzx33h

DH_IPC-HX3(2)XXX_Eng_NP_8M_V2.212.0000.5.R.20140326.bin ……………………………………….. http://tinyurl.com/ke285w5

DH_IPC-HX3(2)XXX_Eng_NP_8M_V2.212.0000.6.R.20140419.bin ……………………………………….. http://tinyurl.com/mllzcox

General_IPC-HX3(2)XXX_Eng_P_V2.420.0000.0.R.20140414.bin ………………………………………… http://tinyurl.com/nftaogy

DH_IPC-HX3(2)XXX_Eng_N_V2.420.0000.0.R.20140414.bin ……………………………………………. http://tinyurl.com/ma5q64d

General_IPC-HX5(4)XXX_Eng_P_V2.210.0000.2.R.20130821.bin …………………………………………. http://tinyurl.com/pdcdmdk

General_IPC-HX5(4)XXX_Eng_N_V2.210.0000.4.R.20130911.bin ……………………………………………….. http://tinyurl.com/pdoxjzj

General_IPC-HX5(4)XXX_Eng_P_V2.210.0000.9.R.20131217.bin ……………………………………………….. http://tinyurl.com/p3g4t54

General_IPC-HX5(4)XXX_Eng_N_V2.210.0000.10.R.20140111.bin ……………………………………………… http://tinyurl.com/mnjpd79

General_IPC-HX5(4)XXX_Eng_P_V2.210.0000.12.R.20140225.bin ……………………………………………… http://tinyurl.com/nssnph6

DH_IPC-HX5(4)XXX_Eng_NP_V2.210.0000.12.R.20140225.bin …………………………………………….. http://tinyurl.com/lcjr8xv

DH_IPC-HX5(4)XXX_Eng_NP_V2.210.0000.16.R.20140421.bin …………………………………………….. http://tinyurl.com/k67gu9u

DH_IPC-HX5(4)XXX_Eng_NP_V2.210.0000.18.R.20140429.bin ……………………………………………. http://tinyurl.com/n779scx

General_IPC-HX5(4)XXX_Eng_N_V2.210.0000.21.R.20140613.bin ……………………………………………… http://tinyurl.com/qd2thhe

General_IPC-HX5(4)XXX_Eng_P_V2.210.0000.21.R.20140613.bin ……………………………………………… http://tinyurl.com/p8q75b4

General_IPC-HX5(4)XXX_Eng_N_V2.400.0000.0.R.20131231.bin ……………………………………………….. http://tinyurl.com/kmd7hu9

DH_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0000.0.R.20140419.bin ………………………………………….. http://tinyurl.com/mb75g2n

DH_IPC-HX5(4)XXX_Eng_P_Stream3_V2.420.0002.0.R.20140621.bin …………………………………….. http://tinyurl.com/laj29k5

General_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0000.0.R.20140419.bin ………………………………….. http://tinyurl.com/mzw85fz

General_IPC-HX5(4)XXX_Eng_P_Stream3_V2.420.0000.0.R.20140419.bin ………………………………….. http://tinyurl.com/ov6krph

General_IPC-HX5(4)XXX_Eng_P_Stream3_P2P_V2.420.0000.0.R.20140419.bin …………………………… http://tinyurl.com/oxgblkq

General_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0002.0.R.20140621.bin ………………………………….. http://tinyurl.com/kejg3fv

General_IPC-HX5(4)XXX_Eng_P_Stream3_V2.420.0002.0.R.20140621.bin ………………………………….. http://tinyurl.com/pfmevdu

General_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0003.0.R.20140930.bin ……………………………………….. http://tinyurl.com/kchslos

General_IPC-HX5(4)XXX_Eng_N_V2.420.0003.0.R.20140930.bin ……………………………………………….. http://tinyurl.com/ok4f8fx

General_IPC-HX5(4)XXX_Eng_N_Stream3_V2.420.0005.0.R.20141205.bin ………………………………………. http://tinyurl.com/qbrfg3k

General_IPC-HX5(4)XXX_Eng_P_Stream3_V2.420.0005.0.R.20141205.bin ………………………………….. http://tinyurl.com/ot99vgw

DH_IPC-HX8XXX_Eng_NP_V2.400.0000.2.R.20140506.bin …………………………………………………. http://tinyurl.com/lbar98x

I will also post the bare metal img files when I get some time which contain the firmware and all the img files including the update.img that can be used for serial recovery.

I have just started the process of uploading firmware… There are much more to come as well as many more camera models.

Also if you have any you want to share please PM me what you have and where I can link them to this thread.

Thanks to Euly for sharing firmware files!

IMPORTANT NOTE FOR IPC-HFW4300S-V2 CAMERAS

The new camera appears to have differences (a few that I already found) that makes some of the general firmware incompatible with them. I have found a workaround, but it is complex. I will try to summarize it in a separate thread in the following weeks. I will also repackage the newest firmware files in versions that will work for the V2 cameras. Stay tuned! In the meantime, you can use General_IPC-HX5(4)XXX_Eng_N_V2.210.0000.21.R.20140613.bin or the PAL equivalent to recover your camera.

Well, that’s all I have time to share for now, but I’ll do my best to put together a comprehensive guide to the inner workings of these cameras and a guide to unbrick in any failed software situation.

Thanks and take care.

<p>The post Unbricking your Dahua IP camera (Tips, Tricks & Firmware) first appeared on NVR IPCAMERA SECURITY.</p>

We can talk directly on phone app for asking courier to put package to a certain place you point, and hear sound from app or TV monitor connected to NVR

We could be alerted any time a person enter your property by receiving push notification from free phone APP, and the alarm light will be triggered to drive away the suspicious objects ( Note: APP has No Monthly Fees)

High Resolution 2592 X 1944 pixel to provide your vivid and clear image no matter in day or night, and IP 67 Waterproof to withstand Changeable Weather like Snowy/Rainy Day

We can customize the surveillance area or set a line for human/vehicle, and the alarm alerts will be triggered when detecting human/vehicle crossing the line or intruding the alarm area （These function may only work with Hiseeu NVR）

Version 2020-2022 PoE System FAQs in total

.

Further support, plz email us at email love@hiseeu.com

Or contact us at +1 917 688 2228

.

Important Notes:

These FAQs are only adaptable to following Models NVR Model : H5-NVR-P-8,

Camera Model: HB215-PA, HB212-PA, HB915B-PA

Mobile Phone APP: XMEye Pro         PC Client :VMS

Hisseu PoE Camera System User Guide v1

Contents:

A:  Forget NVR Password?

B:  Add Device on PC Client Software (VMS）?

C:  How to Sign up account on Mobile APP (XMEye Pro) ?

D:  Add Device on Mobile Phone APP (XMEye Pro)?

E:  How to enable Alarm Notifications on APP XMEye Pro?

F:  Configure Offline Camera or Add a New Camera?

G:  No Video Display on TV Monitor Or Blank Screen?

H:  Why DVR/NVR can’t record or playback video?

.

Detail Solutions:

A:  Forget NVR Password?

1. Please click the mouse from the home screen, and “Logo Out–>Log Out”

2. Right click the mouse again, click “ Main Menu”–> “Forget password –> Forget answer”, you will see the “QR Code”

3. Please open your mobile APP “XMeye Pro”

（1）Click the Scan icon on the top left corner

（2）Scan the “CAPTCHA” on the TV monitor, then you will get a code from the mobile phone APP or from your email, and enter the code into “CAPTCHA”, so you will be able to reset the password on the Monitor connected to DVR

.

B: Add Device on PC Client Software (VMS）?

VMS download link:

For Windows （2023 newest version）

https://download.xm030.cn/d/MDAwMDE0OTM=

For Mac ( 2022 version)

https://download.xm030.cn/d/MDAwMDA2NDA=

1. Download PC Client “VMS” and installed

2. Login with the default User Name and Password. Click “SIGN IN”.

Default User name is: admin

Default Password is: admin

3. Navigate to “Device Manager”–>”Manual Add”

4. Login Type: Cloud ID Device Name:

Name Your Device as you like

Cloud ID : Device Serial Number. We need to go to the TV Monitor connected to the NVR , and find out the information on TV Monitor UI, then right click the mouse to navigate to the path of “Main Menu–>Advanced–>Version” to find out the information “serial number”

User Name and password: Input the user name and password that you created for the NVR , and we also need to find this from the Monitor UI.

.

5. Navigate to “Live View”, Click on the device name(serial number), then select “Open All By Sub Stream”

.

C:  How to Sign up account on Mobile APP (XMEye Pro) ?

Please follow these instructions to sign up for an account via your mobile number.

1. Click on Sign Up

2. Sign Up by email or Select Mobile Number

3. Select the correct country code +1, input your mobile number and click on “Get code”

4. A code will be sent to the mobile phone number, input the verification code and continue.

.

D:  Add Device on Mobile Phone APP (XMEye Pro)?

Steps:

–>1. Please connect the NVR/DVR box to your Router via Network Cable; (Some customers think it can support WIFI connection, while wired systems only support wired router connection, and have to be wired to router via ethernet cable)

–>2. Go to Monitor UI Interface, and Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR/DVR is online (Please skip step3),

–>3. If the cloud status shows “Probing DNS”, Please Navigate to “Main Menu > Network > Check the icon of “Enable DHCP”–>Apply;

–>Reboot the DVR by unplugging the power adapter and re-plug it, then double-check the cloud status ( only cloud status shows )

–>4. Go to your TV Monitor, navigate to “Main Menu–>Advanced–>Version”–> You will see the serial number.

The QR code contains Serial number info. We need this information after we add the device to mobile phone APP

–>5. Open the mobile APP “XMeye Pro” and register an account by your email first

–>6. Click”+” to add device–>Choose “NVR”

Device Serial Number: Click the “Scan” icon to Scan QR Code On the NVR UI Interface (Main Menu–Advanced–Version), (QR code contains username and password)

No need to input the username and password manually.

And click “OK”, and go back to the Device page on App,and you will see the device shows status:online ,

E:  How to enable Alarm Notifications on APP XMEye Pro?

1.Make the Alarm setting is already set on Monitor UI Interface

2. Please right-click mouse and navigate to “Main Menu–> Alarm–>Motion Detect/Human Detect/Face Detect–> Enable “Mobile Reported”–>click “OK”

(Default Setting is for Channel 1, Please select “All” channels.)

2.Open “XMeye Pro” mobile App, and navigate to “Event–>Device (the one you named)–>Enable “Allow Notifications”

.

F:  Configure Offline Camera or Add a New Camera?

—>1. After connect the camera to NVR via network cable, if the camera power on properly, the camera’s indicator light should be blinking.(see picture attached)

.

When you cover the camera’s photocell or put the camera in dark place, the infrared LED should turn on red color.

—>2. If camera powered on properly please follow below instructions.

1.Right-click mouse navigate to “Quick Setup(or Channel Set) –>Cancel

2. In the second box, if any camera status is offline or not connected, please select it and click ”Delete” first

3. Click “Search”, can you see new IP address showed on the topper box?

4. Select the IP address in topper box and click Network–>Auto Assigned–>OK

5. If auto assigned successfully, please click “Add” to add the camera.

.

.

G:  No Video Display on TV Monitor Or Blank Screen?

My UI Interface shows “No signal” or “Black Screen” ？

We need to divert this issue into two situations:

1.NVR Indicator light is on:

(1) Cause: The camera system’s video output resolution is 1080P. If your TV monitor resolution is below 1080P, this issue will occur.

Steps:

Please right-click and hold your mouse for over 10 seconds to see if the system can reboot or not. Or, please try to connect the system to another TV monitor with a higher resolution (above 1080P)

.

(2) Cause: The hard disk drive inside of the DVR box is broken, and use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is having an issue, and needs a replacement, plz contact email love@hiseeu.com for replacement HDD

After steps, if the thing still cann’t be resolved, which means the NVR box is broken, plz contact email love@hiseeu.com for replacement NVR box if their warranty is still 1 year

.

2.NVR Indicator light is off:

(1) Cause: The power adapter 52V 2.5 A connected to the NVR box is broken

Step: Use another power supply 52V 2.5 A to power on the NVR unit to have a try ( If you do not have a spare one, can contact us to buy a new one or we send you a new one if your warranty is still under 1 year )

.

(2) Cause: The hard disk drive inside of the NVR box is broken Step: Use the screwdriver to open the NVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the NVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is broken, and needs a HDD replacement, plz contact email love@hiseeu.com for replacement HDD

.

H:Why DVR/NVR can’t record or playback video?

.

If HDD(Hard disk drive) is having issue or something wrong with record setting, the DVR can’t record/playback the video

.

1.Check if the hard drive status is normal or error

Navigate to NVR/DVR Monitor UI Interface: Navigate to “Main Menu–>Advanced–>HDD info”

If status shows “Error” or No hard drive info , which means the hard drive is broken. (need to replace hard dirve)

2.Check the record plan is set up for 24/7 continuous recording

Navigate to “Main Menu–>Record Conf”

Channel : select “All”

Period: “00:00-24:00”

Select “Regular”

3. Please make sure the HDD was set up to “Overwrite”. (if it was set to “stop”, the system would stop recording when the storage is full)

Navigate to “Main Menu–>General–>Storage Full”

Add Device on Guard Station PC Client Software

Add device to “Guard Station” Download link: https://www.dropbox.com/sh/jeftu4sqwy4y1u8/AAD4PkyEJxg6j4H1n20PxBkZa?dl=0  

.

Please sign up for the mobile APP(Guard Viewer) account and add the device first.

Download and run “Guard Station” on the PC

1) Please Navigate to “Device Management”> “Cloud Device”> Click on “Login”

2) Login with your APP account and password.

3) After Login, the device you added to the APP will list here

Please click on “Control Panel”> “Live View”> Double-Click Camera to load the live view video

Add Cameras to NVR or PoE Switch (Router)

Add Cameras to NVR/ PoE Switch or Router

1. Add camera via NVR PoE Port

• If the camera is connected to NVR PoE port directly, the IP address

range should be modified to “172.16.0.X” (X is between 2 to 255)

Please right-click mouse and navigate to Camera

For brand new camera (password is 123456 by default), NVR will detect

and add camera automatically.

If the camera’s user name or password has been changed, you are required to input the info manually.

Move the mouse to the status icon , you will see the error message. “Offline [incorrect Username to Password]”

Please click on the edit icon to input password manually and click on “OK” to continue.

2.Add Camera to NVR via PoE Switch or Router

NVR will detect the camera under the same WLAN and list IPC here

• Click on plug icon to add the camera. If the camera has default user name: admin, password: 123456.

NVR will add it automatically.

• If the camera’s password has been changed, please click on the setting icon to modify the info.

• In this situation, the camera IP address range should be the same as NVR’s IP range

(You can check NVR IP by navigating to Network>Basic> TCP/IP). If not, please contact the technician to modify the camera’s IP first.

Camera Not working

Camera not working?

1.(Port issue) Insert the camera to another port of the NVR to have a try, and wait at least 5 minutes

2. (Camera issue) Make sure if the camera infrared light will turn on red or not in the night time

3. Also plz right click your mouse to “Menu-Camera”, and take a photo of this whole page and send it to us

（Check how many cameras are discovered）

Also go back to the home screen and Check connection status, to see if it shows” Network disconnected” or “incorrect user name and password”

Device Offline on APP or NVR?

Device Offline on APP or NVR?

If the device shows offline on mobile phone app  “Guard Viewer” , we need to make sure the NVR is connected to network perfectly or not

Go next to your Monitor that connected to NVR, and check out the network status

first navigate to this path first : “Menu–Network–Basic–P2P” , also check the device status is online or not,

if it shows: network disconnected, plz enable the DHCP in this path ” Menu–Network–Basic-TCP/IP ” and click “Apply” . After that, go back to “P2P” and check if the device status is online or not

Also , please make sure the PPPOE needs to be disabled, plz navigate to “Network–Advanced–PPPoE”

Enable Alarm light on Each Camera?

Enable Alarm light on Each Camera?

.

(Alarm light would only work during the night time when the alarm was triggered)

.

1. Set up the Alarm light First Right-click your mouse to “Menu– VCA — Intrusion Detection/Crossing Line Detection– Triggered Actions” , and draw the rules for the alarm type

After you set up an alarm type (Like”Intrusion Detection”, or “Crossing Line Detection”), Click on “Alarm Linkage”, you will have the option to Enable “Alarm Light” (Spotlight is only Available During the Night)

2. Enable Alarm Light on “Triggered Action– Alarm Light” for each channel, and Click “OK”

Forget NVR Password？

If you forget your current password, please follow the instructions to reset it.

1. In the system login interface, please click on “Enter Password” > “Forgot Password”

2.If you filled in your email address as a reserved email when you set up the system, you can reset the device password via the APP(Guard Viewer) by navigate to “Me–General–Forget Device Password”

3.Scan the above QR code by app and the security code will be sent to your email address.

4. Enter the security code from email to reset the password

Additionally, If you the email doesn’t belong to you, plz contact us at love@hiseeu.com for more support

Add Device to APP(Guard Viewer)

.

Auto add is not suggested. Please tap on “Later” if you see this message box.

.

In this situation, it will Auto Search to discover the NVR device connected to the local network. But once your mobile phone disconnects with LAN WiFi, you will not be able to view it anymore.

Please Add devices in this way

1.  Please Tap on “ Menu” icon> Tap on “Devices”> “Add”,

2. Tap on “Scan”> “OK” to scan the NVR QR code

3.Navigate to “Menu– Network> Basic> P2P”

• If the Device Status is “Network connected…” , means device is online   and ready for remote view

• If the Device Status is “Offline” , please check the network connection first, if the problem remains, please feel free to contact us at Love@Hiseeu.com   

After you add the device successful, the “Device status” will be “Online”, and your APP account username will display here.   • You can check your APP user name by navigate to “Me”

• If the username doesn’t belong to you, please click on “Delete” and add it again.

4.Add NVR by scanning device QR code and click on “save”

5.   Please Tap on “Menu ” icon, Tap on “Live View” “Add”

6. Select the device and tap on “Start Live View”

Human Tracking/Detect for Model PK-4YHD985-CT ?

1.To enable human tracking , Set preset point “21”. Here is the video link for your reference: https://www.amazon.com/live/video/07adae4ec34a47618bd754cc6c1f8966?ref_=dp_vse_ibvc1

2.To enable human detection, plz go to this path “Menu–Alarm-Motion” , and choose the camera you want, to enable it

(This doesn’t support customize area)

No Video on TV Monitor or blank Screen?

.

The camera system video output resolution is 1080P, if your TV monitor resolution below that will occur this issue.

.

If possible, could you please try to connect the system to another TV monitor with a higher resolution(above 1080P).

Or, please hold your mouse wheel over 10seconds to see if the system can reboot or not.

If not, plz contact us for further support

How to share Device to others via APP Guard Viewer?

.

One device linked to One User ONLY. The NVR system ONLY can be controlled by one authorized account, who can share the device with others in order to prevent attacking or hacking.

For admin user, please follow the instructions to share the device with others:

.

1.Type on “Menu Icon ” and navigate to “Devices”

.

2.Tape on “… ” > “Share”, You can select a single channel to share or select the entire NVR system to share

(1) Share device by typing in the user name you wanted to share with and selecting function as needed.

• The other user needs to register a Guard Viewer APP account and provide the user name for sharing.

• After that, when this user login the APP will find the device by navigate to “Devices”

(2) Share device by generate a QR code

• Create a sharing password and set the valid period

• Click “Generate”, your APP will generate a QR code

• Other users can use the APP to add the device by scanning the QR code you sent

Download the mobile APP and Sign up for an Account

.

1. Download and install the app.

Please scan the QR code to download the free APP “Guard Viewer”

You also can visit the Apple Store or the Google Play Store to download the Guard Viewer app for iOS or Android devices. Alter installation, tap the icon to launch the app.

2.Register an account and login

For first time use, please create a new account and add the following steps:

Please tap Sign up and follow the on-screen prompt to register an account by email.

<p>The post Hisseu PoE Camera System User Guide v1 first appeared on NVR IPCAMERA SECURITY.</p>

Our products and solutions have been deployed and used daily in more than 100 countries and regions, meeting customer needs in various vertical markets that range from residential to commercial, from healthcare to public safety.

Reset Device Web Password on Akuvox Cloud Platform

Users may forget passwords for logging into device web interface. Follow the steps to reset the web password when the device is connected to Akuvox Cloud.

Step 1

Log into the Akuvox Cloud platform with an installer account.

Step 2

To go to the device Info page, follow the steps.

On the Single-tenant Manager view

1. Click User on the left column.

2. Click the Device icon of the desired user.

3. Click the Info icon of the desired device.

On the Project Manager view

1. Select Community or Office on the left upper corner.

2. Click the Info icon of the desired community or office.

3. Click Intercom Devices and then the Info icon of the desired device.

Step 3

1. On the device Info page, click the Settings button.

2. On the Settings page,

Note

Factory Reset Akuvox Devices v2

Reset Door Phones through Physical Buttons

Note

Power up the devices before resetting them through the physical buttons.

S539, S532, X916 and X912

Hold the reset button with a pin and the device will be reset.

X915, E12 and DB01

Insert a PIN into the hole and hold it to reset the device.

E16, E18, E20 and E21

Remove the back cover of the door phone and hold the reset button to reset the device.

R27, R28, R29 and R20 Series

R27, R28, R29, and R20 series do not support resetting by pressing physical buttons.

Watch the video for other reset methods.

Reset Intercom 2-wire Kit Accounts for Single Tenants

Through resetting, the tenant information will be deleted while the device information will be retained after a tenant moves out. This saves time from repeatedly entering the device information.

Installers

1.Log into the SmartPlus Cloud platform with an installer account.

2.Click Role in the upper right corner to switch between single-tenant and community projects.

3.Click to reset the target user account.

After resetting, the following data will be reset:

The following data will be kept:

The following data will be removed:

Distributors

Distributors can reset the Kit users when the Kit is added directly to the single-tenant projects under the distributor account.

3.Click  to reset the target user account.

After resetting, the following data will be reset:

The following data will be kept:

The following data will be removed:

End Users

End users can delete the family master account on the indoor monitor.

After resetting, a new QR code will be issued to the indoor monitor from the SmartPlus Cloud.

On the SmartPlus Account screen, tenants can scan the QR code to register SmartPlus accounts themselves.

.

How to Configure and Modify the Password

The initial password “admin” is rather weak, easy to crack, thus we provide for you the password change service.

Before Start

The difference between the user mode and admin mode on the web page

How to configure

Website password modification

admin mode
Go to Security >Basic >Web Password Modify, choose user name as “admin”, click Change Password, then enter the old password “admin”, input the new password.

user mode
Go to Security >Basic >Web Password Modify, click Change Password, then enter the old password “user”, input the new password.

Device password modification

System code
System code is used to enter “More Interface”, to adjust the password: More>Settings>More, input the default system code “123456”, tap System Code, input the original system code and new system code.

Setting code
Setting code is used to enter “Settings”, and it is left blank by default. To adjust the password: More>Settings>More, input the default system code “123456”, tap Settings Code, leave the original settings code blank, input the new one.

Steps to Enter Device Web Interface

.

Factory Reset Akuvox Devices

Reset Device Web Password on Akuvox Cloud Platform

Users may forget passwords for logging into device web interface. Follow the steps to reset the web password when the device is connected to Akuvox Cloud.

Step 1

Log into the Akuvox Cloud platform with an installer account.

Step 2

To go to the device Info page, follow the steps.

On the Single-tenant Manager view

1. Click User on the left column.

2. Click the Device icon of the desired user.

3. Click the Info icon of the desired device.

On the Project Manager view

1. Select Community or Office on the left upper corner.

2. Click the Info icon of the desired community or office.

3. Click Intercom Devices and then the Info icon of the desired device.

Step 3

1. On the device Info page, click the Settings button.

2. On the Settings page,

Note

.

Check IP Address of Akuvox Door Phones

IP address(es) can be obtained on Akuvox door phones. With the IP address, you can log into the device web interface for configuration, troubleshooting, and more.

Devices with Numerical Keys or Touch Screens

Check the IP address on the system information screen.

Devices without Numerical Keys or Touch Screens

Check IP address through automatic IP announcement.

Note

You can also obtain the device’s IP address using the Akuvox IP scanner.

Download IP scanner:
https://knowledge.akuvox.com/docs/akuvox-ip-scanner?highlight=IP

Check IP Address of Akuvox Indoor Monitors

IP address(es) can be obtained on Akuvox indoor monitors. With the IP address, you can log into the device web interface for configuration, troubleshooting, and more.

The routes may vary by model.

In this part, C313 is taken as an example.

Exception

To check the IP address of S560, press the # key for about 5 seconds and the device will automatically broadcast its IP address.

Check IP Address of Access Control Terminals

Obtain IP Address via IP Scanner

IP scanner allows you to search the device IP address(es) and to perform targeted device reboot, reset, network setting, etc.

Note

Installation

1. Decompress the rar. file downloaded.
2. Double-click on the setup.exe file.

3. Go through the installation process.

a. Click Next to start the installation.

b. Check to accept the terms of the license agreement, and click Next.

c. Enter User Name and Company Name, and click Next.

d. Click Finish to install the IP scanner successfully. The software icon will appear on the desktop.

Obtain IP Address

Note

To obtain the device IP address, your personal computer should be in the same LAN as the device.

Additional Features

Apart from checking IP address(es), you can export device information and perform targeted device network settings and web interface access, reboot, and reset.

Note

Before applying the following changes, enter the User Name and Password. The default is admin.

Log into Device Web Interface

Enter the device IP address in a browser, and you can log into the device web interface for configuration, troubleshooting, and more.

.

<p>The post Factory Reset Akuvox Devices v2 first appeared on NVR IPCAMERA SECURITY.</p>

Troubleshoot Offline Camera

Troubleshoot Offline Camera

Learn how to troubleshoot when a new Verkada camera is offline

Updated over a week ago

Use this article to read through some common scenarios and try the suggested troubleshooting tips to help. If you still need help, please contact Verkada Support.

What is the LED status of the camera?

Camera has been solid orange for over 10 minutes

Camera is blinking blue for over 5 minutes

Camera is solid blue for over 5 minutes, says “waiting to be connected on Verkada Command”

Roles and Permissions for Cameras

Roles and Permissions for Cameras

Learn about the roles and permissions available for Verkada Cameras

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Cameras.

Org-level roles

Organization-level roles are configured on a per-user basis. Groups cannot be used to set organization-level roles.

Below, click the down arrow to the left of the role to learn more about the role and access.

Org Member

Org Admin

Verkada Cameras Troubleshooting 2024

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

CP52-E PTZ permissions

The CP52-E PTZ camera permissions determine who can manage the Sentry Mode feature.

Permissions model (example)

Here’s a simple example of a permissions model that a typical organization with several sites and users may employ:

Users and their required level of access

Permissions each user should be assigned

.

Set Org Admin permissions

Revoke Org Admin permissions

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Customize roles and permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

Roles and Permissions for Command

Roles and Permissions for Command

Learn about the roles and permissions available to Command users and groups

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Command. It also explains how to customize roles and permissions.

Permission levels

Permissions are set at the following levels:

Daha fazla göster

Permissions considerations

Common user permission configurations

Daha fazla göster

Roles and permissions by Verkada product

.

Org-level roles

Org-level roles are configured on a per-user basis. Groups cannot be used to set org-level roles.

Org member

Org Admin

Access Control Role

.

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

Access Site Admin

.

Customize Roles and Permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

FAQ

Why has my organization disappeared?

Why are cameras missing from my organization?

Why can’t I access certain features or settings, such as other users?

Resolve Issues with Missing Cameras

Resolve Issues with Missing Cameras

Learn how to resolve issues when cameras are missing from your Verkada account

Updated over a week ago

When you log in to Verkada Command, you can only access cameras and video in organizations or sites where your user account has permissions.

Note: Even if you are an Org Admin, you still need to grant yourself permission to view all sites. Learn more about roles and permissions for cameras and Command.

If you log in to Command and cameras are missing or have disappeared, always check user permissions. The most common reason cameras are not visible is that your user account needs permissions to the site(s) where the cameras are configured.

Common reasons that can cause cameras to disappear

Check permissions

If you are an Org Admin, you can check and correct your own permissions:

Resolve Issues with Night Mode

Resolve Issues with Night Mode

Common issues with IR and Night Mode with steps to resolve them

Updated over a week ago

Each Verkada camera has night vision capabilities, using a sensor to detect low-light situations. When external lighting is low, the camera switches to night mode and records in black and white, using infrared (IR) LEDs to illuminate the environment. If the IR is emitted improperly through the dome or reflected into the lens, it negatively impacts image quality.

Common night mode issues

It is imperative that the dome remain free of debris and the camera is installed properly to achieve the best image quality. When viewing footage in night mode if the footage appears obscured it is most likely the result of one of the following scenarios:

Camera always in night mode

If your camera is always in night mode even where there is sufficient light in the environment the lux (light) value may need to be adjusted. If this is the case, reach out to Verkada Support for further assistance.

Environmental obstruction

If the camera is mounted too close to a wall, ledge, or light source, the image quality may be degraded due to IR reflection.

Recommendation. Ensure that cameras are mounted sufficiently far away from surfaces that may cause the IRs to reflect, such as light sources.

IR obstruction

If a first-generation Dome camera (D30 or D50) is operating in night mode when there is plenty of light, the IR sensor is likely obstructed by the camera housing.

To fix the obstructed light sensor, physically rotate the lens barrel assembly 180° so the sensor and IRs are visible through the camera case.

Example: Proper and improper orientation

Note: After rotating the lens barrel, the camera orientation may need to be changed in Command.

<p>The post Verkada Cameras Troubleshooting 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Tapo was created to engage in the small intelligent appliances market, to help people adopt a new smart home lifestyle at an affordable cost. That’s why we insist on Smart, Easy, Secure.

.

What should I do if I fail to configure the Tapo Smart Plug?

The Tapo app will guide you step by step during the initial configuration, but you may not be able to get through all the steps due to some interference. This FAQ will tell you what to do if you have trouble getting through a certain step.

Case 1

The phone is looking for the smart device via Bluetooth or its default 2.4GHz WiFi, if you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

Tapo Smart Camera FAQ v1

Case 2

If you are unable to find your home Wi-Fi network, please refer to the following suggestions.

Troubleshooting tips:

1. The signal strength of your home Wi-Fi network is a bit weak, move the smart device closer to your router for a try.

2. Ensure your home Wi-Fi network is a 2.4GHz Wi-Fi network, the Tapo device does not support a 5GHz Wi-Fi connection.

3. If it doesn’t display the Wi-Fi name of the router automatically, please click on “RECAN” at the upper right corner to refresh the Wi-Fi list.

4. If the router’s SSID is hidden, please choose “Other” to input SSID and password manually.

5. Please change the wireless channel of the 2.4G Wi-Fi network to 1, 6 or 11.

6. Reset the device as per QIG/UG and go through the process again.

Case 3

If you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

1. Ensure you have selected the correct home Wi-Fi network and have entered the correct wireless password. If the Wi-Fi network or password is incorrect, click on “Choose a Network” and select the Wi-Fi network again.

2. Make sure your smart device is within the Wi-Fi range of your router.

3. Turn your phone’s or tablet’s Bluetooth off and back on.

4. If the problem persists, try to reset the smart device as per UG/QIG, and then set it up again.

5. Check if there is a firewall on your router. If yes, please turn it off.

6. Change the wireless security type of the 2.4G network to WPA2.

7. Try to connect the Tapo plug to the hotspot of your cell phone or another wifi network. If it works, please upgrade the firmware for the plug, then reset and reconnect it to your router.

.

What features does Tapo smart plug and Tapo smart switch support?

Currently the Tapo plug and switch supports the following features:

.

How to view Tapo camera on PC/NAS/NVR through RTSP/Onvif Protocol

The Tapo camera supports the RTSP and Onvif protocol, so it can work with third-party NVR or NAS devices that also support the RTSP/Onvif protocol. If a user wants to view the live stream of the camera with a third-party app like VLC Player, iSpy, here is the method for him.

Notes:

1. The username/password is the camera account that you created via the Tapo app. If you haven’t created the username and password, please follow the instruction of Step 1 in this article.

2. The IP address is the camera’s IP address assigned by your host router. You can find it on your host router’s DHCP list or in the Tapo app (Go to the Device Settings page of the camera and tap Device Info to see its IP).

3. If you want to view the live stream of the Tapo camera with a third-party app remotely, you will need to open port 554 for the camera on your host router first. Please enable the TCP forwarding for port 554.

4. You could use ONVIF standards to add the Tapo camera with its username/password and IP address. Please see the example of iSpy in Case 2 to know how to use onvif protocal to control the camera.

5. For Tapo C310, the resolution of the stream1 is determined by the video quality set on the Tapo APP.

If you need to watch the 3MP HD Video via RTSP, please change the video quality to Best Quality on the Tapo APP and use: rtsp://IP Address/stream1

6. If the Camera is inserted microSD card and subscribed Tapo Care, its RTSP stream will fail. You need to remove microSD card or cancel Tapo Care to get its RTSP stream.

7. If you find that there’s no or very little sound when using RTSP/Onvif to watch live stream, please adjust the camera microphone on Tapo APP.

Apart from the Tapo app, Tapo cameras can work with other third-party software to use and manage your Tapo camera.

Note: Before you start, make sure the computer/NAS/NVR and your camera are connecting to the same network or can visit the public IP and port of your camera.

Step 1: Create a camera account in the Tapo app

1. On the Home page, tap on your camera model card to go to the camera Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Advanced Settings, then select Camera Account to create an account (username and password) for camera login on other portals.

You will see a prompt like below (About Camera Account), please read it and tap Understand and Agree to Use, then you can create an account for the camera.

Note: The username and password should contain 6 to 32 characters.

Step 2: Add your Tapo camera on iSpy (Example of Onvif protocol connection)

1. Run the iSpy software on your computer.

2. Click Add on the top left menu and select ONVIF Camera.

3. Enter the Username and Password that you set for your camera on the pop-up window, select Network Address, and click Next. You can customize other parameters if needed.

4. Choose the video resolution and click OK.

5. Customize the camera settings as needed, including Microphone, Talk, Motion Detection, Alerts, Recording, Images, Scheduling, and Storage. You can also change all the settings later. Click Finish to complete adding your camera to iSpy.

6. After adding your Tapo camera to iSpy, you can monitor and manage it using the app. View the live, customize motion detection, check the recordings when motion detected, set recording schedules, record videos and more.

Step 3: Watch your Tapo camera on VLC (Example of RTSP protocol connection)

1.Open the VLC software, select Media > Open Network Stream

2.Fill in the URL of the Tapo camera

The URL of the RTSP live stream for the Tapo cameras will be:

For high quality stream1: rtsp://IP Address/stream1

For low quality stream2: rtsp:// IP Address/stream2

In some software, the URL need to add the port to access live stream, the default port is 554:

For high quality stream1: rtsp://IP Address:554/stream1

For low quality stream2: rtsp:// IP Address:554/stream2

If you fail to stream the Tapo camera via the RTSP/ONVIF protocol, you may refer to the article for the troubleshooting:

https://community.tp-link.com/en/smart-home/forum/topic/652710

To get to know more details of each function and configuration, please go to Download Center to download the manual of your product.

.

How to factory reset the Tapo or Kasa smart plug

.

To restore a Tapo or Kasa smart plug to its factory default settings and re-enable the setup mode, please press and hold the power button for 10 seconds.

The LED status for a factory reset varies by model:

After a completing the reset, you can then connect and configure the device in the Tapo App.

How to avoid noise when monitoring the sound from Tapo camera

Tapo cameras are capable of not only monitoring video stream from the camera, but also monitoring sound collected by the built-in microphone on the cameras. You can turn on/off the sound feature like the monitor screen as below. But to increase or decrease the volume, you need to press the volume button on your phone.

Why is there noise?

Noise is a physical phenomenon and it’s actually inevitable. Basically, the IP cameras including other brands’ have background noise more or less. And those cameras which seem to generate less noise probably have worse sound collecting performance. Tapo cameras are designed with a sensible sound collector which might take some noise in your monitor. Even though it is inevitable at present, we are still trying our best to make improvement and searching for better solutions.

How to reduce the noise?

1.     Please keep your mobile device away from the camera as much as possible. The Tapo camera is designed for remote access and monitoring via cloud service, local usage in close range may cause interference and noise between your mobile device and the camera.

2.    Please reduce the output volume below 50% since a louder volume may enlarge noise decibel. The value between 40%-50% is suggested with not only good sound quality but also minimum noise decibel. As long keep focus on our cloud camera you will find our progress on new models.

Your understanding is highly appreciated!

How to edit Home and Away Mode for Tapo&Kasa Cameras on the Tapo app

.

The Away mode and the Home mode are two different sets of Detection, Alarm, and Notification settings for Tapo&Kasa cameras. You can tap the button on the Tapo app>Cameras tab to quickly apply the preset settings to the cameras when you are home or away.

Note:

Here we take the Home Mode as an example.

For Tapo Cameras:

1. Open Tapo APP, find the Cameras tab at the bottom, and locate the Detection Mode section.

You can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three-dots option.

2. Click on Add Devices if you want to add more cameras to the Home mode.

Click on the Edit icon at the top right corner if you want to delete cameras from the Home mode.

3. Select the camera you want to edit the mode settings. Here we take Tapo C200 as an example, and you can change the Privacy mode, Detection, Alarm, and Notification settings of the camera.

Take the Motion Detection feature as an example. You can click on Motion Detection to turn it on or off, change the Motion Sensitivity, and set the Activity Zones on the Motion Detection page.

And you can also click on Detection>Person Detection or Baby Crying Detection to turn them on or off, and tap Alarm and Notifications to configure the related settings.

4. Click on the Back icon at the top left corner of the Tapo C200 page if you have changed the configurations, and click on other cameras if you want to change their configurations.

After completely presetting the Home or Away Mode, you can tap the Home mode or Away mode card on the Tapo app>Cameras tab to switch your cameras’ settings quickly.

For Kasa Cameras:

Here we take KC115 as an example.

1. Open the Tapo app, find the Cameras tab at the bottom and you can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three dots option.

2. Select the camera you want to edit the mode settings and enter the Detection & Alerts page.

3. You can change the Privacy mode, Detection, and Notification settings of the camera.

Tap Detection > Motion Detection to edit the motion detection function. You can adjust Motion Sensitivity.

Tap Detection>AI Detection to change your AI Detection feature, such as Person Detection.

4. After editing the detection settings, tap Detection & Alerts > Notifications to customize its current settings.

After completely presetting the Home or Away Mode, you can tap the card on the Tapo app>Cameras tab to switch all of your cameras’ detection settings to the mode you want.

.

How can I find the IP address of my Tapo&Kasa camera

Note: Some Tapo battery cameras or doorbells need to work with the hub and can’t connect to the router directly, which do not have IP address.

There are two methods to find the IP address of the camera.

Here we take Tapo C200 as an example.

Method 1: Via Tapo app

1. On the Tapo app> Home page, tap your camera model card to go to the Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Device Info and then you can find the IP address of your camera.

Method 2: Via the web management page of your router

Here we take the TP-Link router Archer C7 as an example.

1. Log in to the management page of your router.

2. Go to Advanced > Network > DHCP Server and locate the DHCP Client List section to find the IP address of your camera.

How can I view continuous recordings of Tapo&Kasa cameras on the Tapo app?

This article will show you how to view continuous recordings on the Tapo app.

Note:

For Tapo Cameras

Here we take Tapo C200 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

Click on Recording Schedule to see the detailed recording schedule settings.

Tap Edit on the Recording Schedule page if you want to change the Continuous Recording and Detection Recording schedule.

And please tap the tick icon at the top right corner to save your changes.

Step 3.

On the camera’s Live View page, tap Playback & Download, select the SD Card icon on the Playback page, select the date, and then you can drag the timeline to view the continuous recordings.

For Kasa Cameras

Here we take KC115 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

On the Live View page of the camera, tap Playback & Download > Playback to view all recordings. Drag the timeline and you can view recordings whenever you want and wherever you are.

What can I do if the video image is upside down on my Tapo&Kasa camera

Tapo&Kasa cameras support the function of Video Rotation, and if the camera video image is upside down on the Tapo app, please refer to the following steps to correct it.

Here we take Tapo C200 as an example.

1. On the Home page of the Tapo app, tap your camera model card or tap the Cameras tab>click on Manage on your camera model to go to the Live View page.

2. On the Live View page, tap the icon on the top right corner to enter the Device Settings page.

.

What can I do if I can’t find my Tapo camera on Tapo APP?

If your device does not appear on your app after completing the configuration process, please try the following troubleshooting suggestions:

1. If you are using a Wi-Fi wireless configuration to connect your camera, please check if the camera has successfully connected to the router. You can verify whether the camera is connected to Wi-Fi by checking the System light of your camera. For most Tapo Cams, if it is not connected properly, the LED light will blink red slowly. For the HomeKit version Camera, its LED light indicator will blink blue slowly. If the camera cannot connect properly, we recommend resetting the camera to factory default settings as per the User Guide and then reconfiguring the camera.

How to reset my Tapo camera

2. Check the DHCP settings on your router and ensure that the DHCP Server of your router is enabled. If the camera has already connected to the router properly, you will see the device in the client list of your router. If you don’t know how to do this, please contact your router’s customer support.

3. Please verify if there are any special symbols in your Tapo account（TP-Link ID） password. If there are, try to remove them and make the account password simpler by only using numbers and English letters. Then reset and add the camera from the beginning again.

4. Connect your smartphone to the same Wi-Fi network as your camera and check whether you can see it on the Tapo app. If you can see it, that means the camera fails to connect to the cloud for unknown reasons and you cannot access it remotely. In this case, verify if any firewall or security settings are blocking the connection to the Cloud Server. Temporarily disable any antivirus, firewall, or security software to see if it resolves the issue

.

5. Using a public DNS server may improve the connection, try changing your router’s DNS server settings to 8.8.8.8. If you don’t know how to do this, please contact your router’s customer support.

To eliminate potential issues with the router’s Wi-Fi network, it is recommended to use a mobile hotspot and configure the Camera to test its functionality.

Here are steps for using a mobile hotspot to test the Camera’s configuration:

Preparation: We suggest having two phones. Use one phone (Phone A) to create a hotspot and use another phone (Phone B) to download the Tapo app and complete the setup process.

Steps:

1. On Phone A, disable Wi-Fi and enable only mobile data.

2. On Phone A, navigate to phone settings and access the “Personal Hotspot” or “Mobile Hotspot” option, ensuring that the “Mobile Hotspot” feature is activated. Please make sure the created hotspot operates on a 2.4GHz network.

3. Set a unique name and password for the hotspot, different from your router’s Wi-Fi, to facilitate the Camera’s connection.

4. On Phone B, download the Tapo app. Follow the app’s instructions to add the device and complete the remaining setup steps as guided by the app.

Please contact TP-Link technical support with the following information if the issue persists after the above suggestions.

1) Your TP-Link ID or cloud account.

2) The model number of your TP-Link Cam and its MAC address.

3) The model number of the host router.

4) Whether you have tried all the suggestions listed above or not. If yes, what are the results?

<p>The post Tapo Smart Camera FAQ v1 first appeared on NVR IPCAMERA SECURITY.</p>

How to Change the Password on a 5.0 UI IP Camera

.

IPCamera/Change Password 5.0 UI

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the current username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the System option from the drop-down list

3. Select Account on the left.
Then select the User tab at the top.
Click on the Edit (Pencil) icon to the right of the user account who’s password you want to edit

4. Enable the Change Password slider.
Then enter the current password in the Old Password field.
Enter the new password you want to change it to in both the New Password and Confirm Password fields.
Click on OK at the bottom

5. Once the new password is successfully changed, you will see “Modify User Succeeded” at the top

Dahua IP Camera 5.0 UI Setup

How to Set the Date and Time on a 5.0 UI IP Camera

.

IPCamera/Set Date and Time 5.0 UI

Description

This guide will show you how to set the Date and Time on a IMaxCamPro IP Camera with the 5.0 User Interface

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the System option from the drop-down list

3. Select General on the left.
Then select the Date & Time tab at the top.
To set the date and time without an NTP server, select Manual Setting. Then adjust the Time, Time Format, and Time Zone. (You can press Sync PC if you want to pull the time from the PC you are using. The Time Zone still needs to be set manually though.)

To set the date and time with an NTP server, select NTP. Then fill in the information for a functioning NTP server. (This will only work if the camera has access to the internet.)
For locations that use Daylight Saving Time, enable the slider below DST and select the dates and times that Daylight Savings starts and stops.
When you are done adjusting settings, select Apply at the bottom to save the settings.

How to Set the IP to Static on a 5.0 UI IP Camera

.

IPCamera/Set IP to Static 5.0 UI

How to Set IP Settings to Static on a 5.0 UI IP Camera

Description

This guide will show you how to set the IP settings to static on a ImaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the Network option from the drop-down list

3. Select TCP/IP on the left.
Click on Static next to “Mode”.
Then fill in the IP Address, Subnet Mask, Default Gateway, and DNS settings below that. (You can press the “Test” button if you want to see if that IP address is free on your network.)
When you are done adjusting settings, click on Apply at the bottom

How to Configure Recording to an SD Card on a 5.0 UI IP Camera

.

IPCamera/Configure Recording SD Card 5.0. UI

How to Configure Recording to an SD Card on a 5.0 UI IP Camera

Description

This guide will show you how to configure recording to an SD Card on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Select the Gear icon at the top right.
Then select the Storage option from the drop-down list

3. Select the SD card from the list by enabling the radio button on the left.
Click on Format at the top to wipe all the data on the SD card and configure it for recording on this camera.

4. Click on the Home icon at the top left.
Select Record. (If you don’t see it on the main page, click the right circle at the bottom to switch pages.)

5. Select the Record Control tab at the top.
Adjust the settings on this page as desired:

When you are done adjusting settings, click on Apply to save the settings

6. Select the Time Plan tab at the top.
Adjust each Event Type on the weekly calendar.
When you are done adjusing the schedules, click on Apply to save your changes

7. Select the Storage tab at the top.
Adjust the settings on this page as desired:

When you are done adjusting settings, click on Apply to save the settings

How to Playback Video from an SD Card on a 5.0 UI IP Camera

.

IPCamera/Playback Recording SD Card 5.0. UI

How to Playback Video from an SD Card on a 5.0 UI IP Camera

Description

This guide will show you how to view recorded video footage from an SD Card on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

1. Input the camera’s IP address into a web browser.
Enter the username and password of the camera into the designated fields.
Click the Login button to log in

2. Click on the Home icon at the top left.
Select Record. (If you don’t see it on the main page, click the right circle at the bottom to switch pages.)

3. Select the Search Video tab at the top.
Select the start date and time, and the end date and time on the left.
Then click Search below that.
All the recorded footage on the SD card in the time range will appear.
Double-click on the specific clip you want to play

4. Move the slider at the bottom to adjust the playback time.
Use the controls to play, pause, rewind, fast forward, or jump between clips

IPCamera/Password Reset 5.0. UI

.

IPCamera/Password Reset 5.0. UI

How to Reset the Password on a 5.0 UI IP Camera

Description

This guide will show you how to reset the password on a IMaxCamPro 5.0 User Interface IP Camera

Prerequisites

Step by Step Instructions

Reset via Password Recovery in DMSS

1. Input the camera’s IP address into a web browser.
Click on Forgot password?

2. Click on OK to agree to use your email address in this process

3. If you setup a recovery email you will be brought to a page with a QR code on it. (If you didn’t setup a recovery email, skip to “Reset via Physical Button” at the bottom of this page.)

4. Open the DMSS app on a mobile device.
Tap on Me at the bottom.
Then select Tool Manager

5. Tap on Device Password Management

6. Use the mobile device’s camera to scan the QR code from Step 3 above

7. Once the QR Code has been successfully scanned you will see the following message

8. Check the email inbox for the email address that was registered for password recovery on this device.
Input the security code from that email in the Security code field.
Then click on Next

9. Enter a new password in the New Password and Confirm Password fields.
Then click on OK

10. The password will be successfully reset

Reset via Physical Button

Depending on the model of your IP Camera, there could be a physical reset button on the outside body of the camera, or inside the camera body.

1. Reset: Press the reset button for 10-20 seconds while the camera is connected to power.

IP Camera Basic Info

Important Safeguards and Warnings

1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The product must be grounded to reduce the risk of electric shock. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.

2．Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.

3．Installation

4．Qualified engineers needed All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment The NVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. This series product shall be transported, storage and used in the specified environments.

6. Accessories Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package.

7. Lithium battery Improper battery use may result in fire, explosion, or personal injury! When replace the battery, please make sure you are using the same model! Before your operation please read the following instructions carefully.

Hardware Installation and Connection

Note: All the installation and operations here should conform to your local electric safety rules.

1. Check Unpacked NVR When you receive the NVR from the forwarding agent, please check whether there is any visible damage. The protective materials used for the package of the NVR can protect most accidental clashes during transportation. Then you can open the box to check the accessories. Please check the items in accordance with the list (Remote control is optional). Finally you can remove the protective film of the NVR.

2. About Front Panel and Rear Panel For detailed information of the function keys in the front panel and the ports in the rear panel, please refer to the User’s Manual included in the resource CD. The model label in the front panel is very important; please check according to your purchase order. The label in the rear panel is very important too. Usually we need you to represent the serial number when we provide the service after sales.

3. After Remove the Chassis Please check the data cable, power cable, COM cable and main boar cable connection is secure or not.

4. Important：Please turn off the power before you replace the HDD. You can refer to the User’s Manual for recommended HDD brand. Please use HDD of 7200rpm or higher. Usually we do not recommend a PC HDD. For detailed operation instruction, please refer to the User’s Manual included in the resources CD.

1. Use the screwdriver to loose the screws of the rear panel and then remove the front cover.

2. Put the HDD to the HDD bracket in the chassis and then line up the four screws to the four holes in the HDD. Use the screwdriver to fix the screws firmly to secure HDD on the HDD bracket

3. Connect to the HDD data cable to the main board and the HDD port respectively. Loosen the power cable of the chassis and connect another end of the power cable to the HDD port.

4. After connect the cable, put the front cover back to the device and then fix screws of the rear panel.

<p>The post Dahua IP Camera 5.0 UI Setup first appeared on NVR IPCAMERA SECURITY.</p>

InVid Tech is here to help you succeed, and as a company, we pride ourselves on the level of personal service we offer. We have an experienced team based in the United States, including Sales, Customers Service, Marketing & Tech Support. Additionally, there is support for Latin American Countries.

Steps to Change Secure Series Camera Compression to H.264

The below steps are needed in order to connect your camera to the Secure 4ch NVR attached with your order.  Please log into camera first, default username is “admin” and default password are “1234567u”, from there it will prompt you to change, please do so and follow below steps.  If you do not do this first, the camera will not connect to the NVR.

SEC-BODYTEMPCAM1 Camera Configuration Guide

**Please Note:  Cameras Default IP address is 192.168.1.121.  IP Utility can be downloaded off our website here

• Log into the cameras web interface on Internet Explorer (IE), default username is “admin” and default password are “1234567u”. Make sure to download the new plugin. 

Note: close ALL browser tabs while installing the plugin.

• Parameter Configuration (Configuration/Human Thermometer/Parameter Configure)

◦ Enable face detection

◦ Draw the area according to the real scenario, there is a maximum of 8 areas supported. We usually use one detection area to cover where people could potentially appear in, recommended distance is 9 to 16 feet (3-5 meters) for capturing.

• Leave the Display Trace Info at “Mode 1”

• Show Detection Area, can turn On or Off

• For Confidence Coefficient, we suggest keeping the default value (Mid). It’s for the face matching level with the built-in algorithm.

• Area ID is for the selected areas if you choose more then one main area, up to 8 totals. We suggest keeping this at one and focusing on the main point of entrance.

• For Face Pixel Minimum and Maximum, we suggest keeping the default value (70/1000). Only faces in this range will be detected.

• There are two different Snapshot Modes: 

◦ Timing: ‘upload interval’ is associated with ‘timing’, camera will upload one picture every 5 seconds (Suggested).

◦ Optical: ‘snapshot count’ is associated with ‘optical’, camera will upload the best face picture in 5 seconds.

• For Upload Image Interval we suggest leaving at 5 seconds (1-10 second range).

• For Yaw Degree, Tilt Degree, Pitch Degree and OSD Overlay Snapshot, we suggest keeping as default.

• FTP Upload Image Matting and FTP Upload Whole Image are if you are using the camera as a standalone device, no CMS or NVR, and wish to save the facial snaps to an FTP.

• Temperature Parameters

• Enable this field and leave all as DEFAULT except LENGTH UNIT and MOUNT DISTANCE

◦ IF YOU SWITCH TO FAHRENHEIT THE FIELDS STILL STAY AS DEFAULT (Except Length/Mount Distance, mentioned above)

◦ DEPENDING ON THE SELECTION OF “LENGTH UNIT” (METERS/FEET), ALL DISTANCE FIELDS WILL BE CONSIDERED IN THOSE UNITS!

[IMPORTANT] Set the mount distance according to the real installation, whose value should be the horizontal distance from the detection area to the camera. 

Hit ‘apply’ to save the settings.

• Face Alarm Linkage

IF SWITCHED TO FAHRENHEIT YOU MUST ADJUST “ALARM TEMPERATURE”, 99.5-100.5F (Default Celsius is 37.30)[

• [IMPORTANT] Thermal Mapping (Configuration/Human Thermometer/Thermal Mapping)

◦ This step is mainly for matching the thermal image with the visible image, which can ensure the measurement accuracy.  The Black Body device (Infrared Calibrator) MUST be in the Field of View of the thermal image.  The thermal image is a FIXED LENS and is a smaller field of view then the standard image.

• There are eight groups of ID, and each group ID contains three points. If using One area, then you do not have to set groups 2-8.

• Pick out three points that you can clearly see in the thermal image, mark them with point1, point2 and point3.

• Find the three locations of the three points in the visible image and mark them with the same point numbers associated with those in thermal image.

◦ Note: Suggested to choose three points far away from one another, so the triangle of can cover 70% of the image.

• Hit ‘apply’ to save the settings.

• Test if the rectangle can correctly surround the face, and perfect it by adjusting the three points.

• Thermal calibration (Configuration/Human Thermometer/Thermal Calibration)

• Install the blackbody properly where the camera can see it (within the thermal image). The blackbody needs to be powered on for at least 20 mins to reach to a stable temperature.

◦ The Infrared Calibrator will ALWAYS display in CELSIUS; the stable temperature is ~40C

• Enable.

• If you turn on ‘Display Area Info’, the blackbody (Infrared Calibrator) will also be shown with temperature on thermal image.

◦ Draw box around your calibrator

• Target Temperature: If using Celsius leave as 40C, if using Fahrenheit change to 104F (Default)

• For Distance, put the real installation distance between the camera and Black Body (Infrared Calibrator). No more then 9-16 feet (3-5 meters).  Distance is in Meters or Feet, depending what you selected under the Parameter Config menu.

• Keep the ‘Emission Rate’ as the default value.

• Hit ‘apply’ to save the settings.

InVidTech Secure Series Setup Guide v1

Also Read : How To Setup O-KAM Pro camera

SEC BODYTEMPCAM1 camera run off of POE output?

Yes it is, safe.

What are the minimum specs required to handle SEC-BODYTEMPCAM1?

For a single camera: i7 processing, at least 8GB of RAM.

From where is the temperature being scanned?

From a point in the middle of the forehead, the temperature is scanned, above the nose and in-between the eyes. If the camera captures a profile image it is using the skin around the earhole for temperature.  It is important to note that what is being scanned is skin temperature and not core temperature.

Should people be screened prior to entry?

The camera needs to be set within a controlled environment and cannot be installed outside. The calibrator isn’t weatherproof (IP66) and airflow, whether inside or out, could throw off the camera’s calibration.

If you need to screen people before entering the building, you would need to set up an enclosed tent to scan individuals. The camera can operate in both extreme heat and cold as long as no airflow would skew the results. If an individual is outside for an extended period, in the intense heat or cold without the opportunity to reregulate their temperature, the results might be slightly off, its recommended to wait 20-30 seconds before reading.

Need to wait when coming from outside for accurate reading?

Most of the time, there will not be any accuracy issues when getting scanned. If you have been out in the extreme heat or cold for an extended time you may want someone to wait roughly 30 seconds for their body to adjust to the environment. The camera is taking the skin temperature, which the human body keeps in check very efficiently.

What is your advice for poorly controlled environments?

If you are going to invest in the product, you will also need to invest in creating a controlled environment. If the environment is not controlled, you will not have accuracy. 

What effects an individuals’ temperature?

An individuals’ temperature will not read higher based on wearing a darker colored cap or clothing. The temperature scanned is the skin. The camera is using the face detection analytic to detect a human face then apply the algorithm built into the camera to display a temperature that is read from the epidermis of the forehead, or if it is a profile picture captured, the skin around the earhole is used.

If you’re wearing a mask, glasses, hood, hat, or all combined, if those two focal points aren’t blocked, then the camera can give a temperature reading.

Depending on the type of hat, for example, a forwards facing baseball cap pulled down entirely over the forehead can cause an individual not to be scanned. Another factor that could affect the scan is how the camera is mounted. The cameras must not be mounted higher than 8-feet. If the camera is wall-mounted and facing on a downward angle where a hat or hardhat is blocking the forehead, a solution would be to mount the cameras on a tripod to get a more direct shot.

Please watch the scenario video here for more info on this.

As for individuals who have been out in the extreme heat or cold for an extended time you may want to wait about 30 seconds for their body to adjust to the environment. The camera is taking the skin temperature, which the human body keeps in check very efficiently.

Two real-life examples of cold and hot temperatures:

In New York, the temperatures were averaging 45 degrees, and we had someone whose drive into work took about 20 minutes. While driving, they had the window rolled down and the air continually blowing into their face. They would walk from their car to the office and could feel their skin was cold. When walking into the office, they would get scanned, and their temperature would be between 96.9 and 97 Degrees. After waiting for about 60 seconds, they would rescan, and their temperature would average the mid 97 degrees.

In Arizona, where the temperature was over 100 degrees, we found that when someone was outside for a while, a cooling down about 20-30 seconds was necessary. Initially, their temperature registered at about 102, but after 20 seconds, it stabilized and showed their baseline temperature.

Something to keep in mind is that everyone is different. Two people who are excessively overheated may vary slightly in how fast their bodies regulated their temperature. One person might take about 10 seconds, while another person might take about 45 seconds. We are finding that the average is about 20-30 seconds for someone to regulate back to their baseline skin temperature.

Does the subject have to face the camera?

The subjects face must hit the 7% FOV (Field of View) mark of the camera to get an accurate reading. It is looking for two measurement points. The first point is in the middle of the forehead, roughly the area in-between the two eyes, near the nose, and if it captures a profile image, it is looking for the skin around the ear hole. The person has to be walking into the view of the camera and not away.

What is the ETA on the Fahrenheit firmware fix for US sites?

The firmware is currently available, giving the option for Fahrenheit or Celsius. The product leaves our warehouse with this latest firmware update, and the product comes defaulted to Fahrenheit & Distance comes defaulted to Feet with the option for metric units. 

What VMS’s are supported?

As of today 4/29/20, we know Axxon and EXACT are working on an integration. Other companies that have reached out but are not 100% confirmed yet. The SDK is available upon request but each is responsible for their integration. 

Without an NVR, will images be stored?

No. The camera will not store any images. 

Will the camera do face recognition without an NVR or computer?

The camera only does face detection. The CMS is what handles Facial Recognition if you aren’t running the CMS, face images will not be saved.

Will the camera track a person?

Tracking is based on facial detection. As soon as the 7% mark is met (7% is the required amount to get a temperature), it will read the face detection analytic and then apply the algorithm for the temperature display.  

Where are these cameras made?

The cameras are manufactured in China but are not affiliated with and are not OEM made products from Hikvision or Dahua. 

Can the camera just be connected to a LAN that has the NVR on it?

Yes, it can be stand alone.

What is the accuracy of the camera?

The accuracy of the camera is 0.54 Degrees Fahrenheit / 0.3 Degrees Celsius.   

Is this camera FDA approved for taking Body Temperature readings?

We are currently in the process of working on our 510k Certificate approval. 

Will the camera pick up the temp of a person who is walking away?

No. it is not designed to work this way.  Depending on the angle, it might be able to capture a profile and on occasion provide a temperature. 

Is there a max mounting height from the floor?

Yes, you may not exceed 8 feet from the floor when installing on a wall or ceiling mount.

How do you calibrate the calibrator?

Let the calibrator run for about 15-20 minutes. On the back panel of the calibrator, you will see a display. The display will be in Celsius regardless of the settings in the camera and CMS. Once the screen hits the 40-40.2 degrees, the unit has been calibrated. 

Can you set the camera and calibrator to shoot through a glass door?

 No, the camera and calibrator must be in sight of one another and cannot see through a glass window or door. There can be no glass between the devices and the subject. 

How far away does the calibrator need to be from the camera?

The camera and calibrator must be in view of each other and must not exceed 16 Feet. The recommended distance is 7-16ft. and the calibrator must be in the field of view of the THERMAL image

Does each camera require its own calibrator?

Yes, each camera requires its own calibrator. You cannot use two cameras with a single calibrator. The temperatures will not be accurate. 

Can you connect the CMS to a customer’s network?

Yes, the CMS can be connected to a customer’s pc and also run on a pc that is not on the network.

What does CMS stand for?

Central Monitoring Software

Is the CMS included with the purchase of camera & calibration device?

Yes, there is a free download that is available on our website. There is no charge. You can find it here

How many users can log into the CMS simultaneously?

The CMS (Central Management System) is stand-alone. You can install it on multiple computers, but there is a max of 10-user connections for each camera.  

CMS (Central Management Software) for PC

CMS for PC

This is the free CMS (Central Management Software) for the Secure Series for those using a PC. It will work with Secure Series Products. 

New in this Version:
.

Version V1.8.163.0.0.51.0_build 20240206

User Name: admin
Password: 1234567u

Download Secure CMS Here

Download AD (Active Directory) Instructions Here

IP Tool Utility for PC

This is the free IP utility for the Secure Series for those using a PC. It is used to find IP Cameras on the network and change the IP info (IP Address, Sub-Net, Default Gateway) of those devices. Version v1.9.9

Supported Devices: Secure NVRs, Secure IPCs

Download IP Tool Here

If you are using a computer, will it record video without an NVR?

No, the closest workaround is to add the camera to the CMS. The CMS saves snapshots based on facial recognition. Please keep in mind that if the CMS doesn’t see specific points of a face to realize its a face (such as if the person is partially covered), you may still get a temperature read, but the face snap may not save. The CMS is only saving snapshots, not video.

How to use a cloud feature in the NVR menu?

The cloud feature will be implemented in the future. Once it is fully functional, we will have additional information posted!

How many hours of video can be stored on the NVR?

That will depend on the size of the drive you put in the unit and the number of cameras you have installed. The standard 4-channel unit can house a single hard drive bay, and can use drives ranging from 1-10 Terabytes. 

Can the NVR do the job of counting and temperature notification?

No.

Will camera send notifications automatically without an NVR?

If the camera is networked, email notifications can be sent out, even without an NVR. This will include a snapshot with the temperature for individuals who are above the threshold set. The camera also has two alarm outputs that can be utilized.

To use the app, InVid LIVE CMS, the camera would need to be added to the CMS, and the CMS would have to be kept open and running on a PC. If a temperature over the threshold is registered, it will send a push notification to the app.

Is the NVR required for sending email alerts?

No, the camera can send out email alerts. The 4/8/16 Channel NVR does not have the ability to send out email alerts while the 32 channel unit does, for over temperatures.

What type of notifications are triggered by high temp?

You can have an email notification with a snapshot of the individual and temperature range and also the option of one or two sirens if the temperature is above the threshold. 

Are there any onboard relays that could be triggered to send an alert

Yes, the camera has 2-alarm outputs. Power is needed, 12/24 volt AC/DC. Settings within the camera can be configured to trigger an alert when a temperature is over the threshold. 

Can the system send email and text alarms?

The system can send emails, it includes the picture of the scene with the temperature reading. Currently, there are no text alarms, but it is something we are looking at trying to implement.

Audible alarm once it detects a high temp?

The camera has two notification functions. The first is an email notification. The second is an alarm output trigger. The CMS that links to the camera does have an audible alarm if your computer is set up for sound. 

What is the warranty on the Secure Series products?

Camera: 1-Year

Calibrator: 1-Year

NVRs: 2-Year on Unit & 2-Years on Hard Drives

.

<p>The post InVidTech Secure Series Setup Guide v1 first appeared on NVR IPCAMERA SECURITY.</p>

ATTENTION: Prior to purchasing and installing an accessory antenna, read the product specifications of your receiver to determine if your receiver has a weatherproof housing. Installing your weatherproof receiver outdoors provides a better line-of-sight between the receiver and the camera, increasing the strength of the wireless signal. See your product specifications to determine the weatherproof rating of your receiver.

The Directional Wireless Panel Antenna and the Omni-Directional Antenna are used to extend the range of one or multiple wireless or wire-free cameras.

Directional Wireless Panel Antenna (ACCANTD9)

Omni-Directional Antenna (ACCANTO8)

Use the 2.4GHz Directional Wireless Panel Antenna (ACCANTD9) to focus a wireless signal onto one specific wireless device (camera or receiver) to increase the range of transmission. A clear line-of-sight between the antenna and the wireless device needing range extension is required.

Use the 2.4GHz Omni-Directional Antenna (ACCANTO8) to enhance the signal of one or multiple cameras that are paired to a single or dual antenna receiver. You may also use two Omni-Directional Antennas to extend the range of all cameras paired to a dual antenna receiver.

REQUIREMENT: To connect the antenna directly to the camera or receiver, the device must have a removable SMA type antenna. Visit www.lorextechnology.com/compatibility to ensure the antenna is compatible with your camera or receiver model.

Lorex Wireless Cameras and Monitors guide 2024

Also Read  : Lorex Camera Troubleshooting

Recommended Antenna Installation Methods

Your antenna needs will vary depending on the setup of your camera system, the number of cameras that require range extension, and the number of channels on your wireless receiver. Review the scenarios below to ensure you have the correct antenna and installation method to meet your needs.

Click a setup scenario to see the recommended installation method:

Combining Accessory Antennas

If you have installed your accessory antenna according to the recommended installation methods and would like to enhance wireless signal strength even further, you may add an additional Directional Wireless Panel Antenna (ACCANTD9) directly to a camera. The additional Directional Wireless Panel Antenna can be used with a Directional Wireless Panel Antenna or with an Omni-Directional Antenna attached to the receiver.

Click an antenna combination to see recommended installation methods:

Scenario 1: Extend the range of one camera paired to a single antenna receiver

To extend the range of one camera connected to a single channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9).

The Directional Wireless Panel Antenna can be connected in two configurations.

Configuration 1. Connect the antenna directly to the camera

Configuration 2. Connect the antenna directly to the wireless receiver

REQUIREMENT: The antenna connects using an SMA cable and replaces the existing antenna on either the camera or wireless receiver. Check www.lorextechnology.com/compatibility to determine if your product is compatible with the antennas.

Scenario 2: Extend the range of one camera paired to a dual antenna receiver

To extend the range of one camera connected to a multi-channel receiver, use the Directional Wireless Panel Antenna (ACCANTD9). Connect the Directional Wireless Panel Antenna directly to the camera.

Scenario 3: Extend the range of select cameras paired to a dual antenna receiver

To extend the range of select cameras on a multi-channel receiver, use the Omni-Directional Antenna (ACCANTO8).

Connect the Omni-Directional Antenna to one of the antenna ports on the wireless receiver.

REMINDER: Each antenna port on a dual antenna receiver is associated with specific camera channels. One antenna communicates with odd numbered channels (1, 3, and 5), while the other antenna communicates with even numbered channels (2, 4, and 6). See the table below for dual antenna channel configurations.

If you connect the Omni-Directional Antenna to an antenna port and your wireless signal does not improve, try switching the Omni-Directional Antenna to the other antenna port or pairing your camera to a different camera channel.

Scenario 4: Extend the range of all cameras paired to a dual antenna receiver

To extend the range of all cameras on a dual antenna receiver, connect an Omni-Directional Antenna (ACCANTO8) to each antenna port on the receiver.

IMPORTANT: Two Omni-Directional Antennas are required to accommodate this setup.

Combination 1: Combine two Directional Wireless Panel Antennas

If you are using a Directional Wireless Panel Antenna (ACCANTD9) to enhance the signal of a single camera with a single channel receiver, you can use an additional Directional Wireless Panel Antenna to further enhance the wireless signal.

Connect one Directional Wireless Panel Antenna directly to the camera and one Directional Wireless Panel Antenna directly to the wireless receiver. To maximize signal strength, it is recommended to aim the two antennas directly at each other with a clear line-of-sight.

Combination 2: Combine a Directional Wireless Panel Antenna with an Omni-Directional Antenna

If you are using an Omni-Directional Antenna (ACCANTO8) to enhance the signal of multiple cameras, you can further enhance the signal of a specific camera by connecting a Directional Wireless Panel Antenna (ACCANTD9) directly to the camera.

A clear line-of-sight between the Directional Wireless Panel Antenna and the Omni-Directional Antenna is recommended to maximize signal strength.

Lorex SD Pro App: Changing / resetting the password

If the password for the Lorex SD Pro app to view the Wireless Home Monitor is lost or forgotten it will need to be reset.

To reset the Lorex SD Pro app password:

1.Ensure that your Wireless Home Monitor is connected to a network router using the included Ethernet cable.

2.On the Wireless Home Monitor tap the Menu icon ().

3.Use the joystick to select Settings > Network > Reset Password.

4.Select Yes to confirm.

5.Tap the Menu icon () repeatedly until all the menus are closed.

6.Launch the SD Pro app and enter the default password. Refer to your user manual for your default password. You will be prompted to create a new password.

Lorex SD Pro App: Setting up Wireless Home Monitor remote access

You can access and view wireless cameras from a Wireless Home Monitor system using an iPhone, iPad, or Android smartphone or tablet using the Lorex SD Pro app. It is available at the App Store or Google Play Store.

Prerequisites:

To set up the mobile application:

LW2700 Wireless Home Monitor: Included cables and accessories

LW2700 Series Wireless Home Monitors support wireless cameras using a wireless signal. They do not have an internal battery and require a connection to a power source. Refer to your user manual for model specific information on cables and accessories. Click here for downloads and documentation for your product.

Most wireless home monitors include the following cable connections and accessories when purchased:

Network: Wireless camera Internet requirements

Standard wireless cameras that connect to a DVR / NVR, do not need access to the Internet to function. Stand-alone IP cameras do not require an Internet connection for basic functions, but an Internet connection is required for full functionality.

Security Cameras: Understanding Field of View (FOV)

Field of View (FOV) is the maximum observable area that is seen at any given moment through an optical device such as a camera lens. The coverage of the area can be measured using the horizontal and vertical distances to find the diagonal of the area in degrees. Mathematically, the FOV is calculated using the horizontal dimension of the sensor (h) and the Focal Length (F).

You can find the camera’s Field of View details in the Specifications sheet. Click here for additional support content including security camera documentation.

The Camera Lens, Sensor and Focal Length

Focal length (F) is the distance between the center of a lens and its sensor. The size of the lens is the aperture size.

These factors affect field of view. A narrower focal length captures more of the scene and displays a larger field of view. A wider focal length magnifies a scene and decreases the field of view. The higher the focal length value the lower the FOV.

Types of Camera Lenses

Fixed: a fixed camera focal length provides an Angular FOV which is permanently set and cannot be adjusted by the user. Varifocal: the camera focal length can be manually adjusted by the user. Generally, this is done manually with screws or dials. At Lorex we have motorized varifocal cameras that allow you to digitally zoom using your phone or NVR without losing details. These lenses provide flexibility and customization for your camera image needs.

The importance of Field of View

A wide angle lens or smaller lenses produce a greater field of view and captures more objects in a scene enhancing your ability to cover larger and wider areas such as foyers, parking lots or warehouses.

A narrow angle lens or larger lenses produce a smaller field of view; capturing a limited area, but the camera quality image improves in detail. These are designed to monitor a specific object, such as cash registers, entrances/exits, hallways or objects of value.

How to Calculate the FOV

To calculate the FOV requires the sensor size and the focal length of the lens: h = Sensor Size F = Focal Length of the Lens

FOV is represented by this equation: FOV = 2tan-1(h) / 2F

Example: h = 4.7mm F = 6mm FOV = 2tan-1(h) / 2F = 2tan-1(4.7)(12) = 2tan-1(0.39) = 2(21.4°) = 42.8°

W482CAD – 2K Wi-Fi Camera : Frequently Asked Questions

The following FAQ article answers many of the general questions about the 2K Wi-Fi Camera with Smart Deterrence (W482CAD). Where applicable, the FAQ includes links to articles where you may find more information.

.

Where do I place my Lorex 2K Wi-Fi Camera?

.

How should I position my Lorex 2K Wi-Fi camera?

When mounting the camera on a wall, make sure of the following:

 Accuracy of person detection will be influenced by multiple factors, such as the person’s distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection.

.

How do I enable motion detection and person detection?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap  icon to enable Motion Detection.

Note: If motion detection is disabled, general/person/vehicle detection will automatically disable and you will not receive any motion detection notifications in the Lorex App.

.

How do I customize Motion Zones™?

Motion Zones™ allows you to customize your device’s motion detection region. Motion Zones™ screen consists of the following settings:

To set Motion Zones™

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Motion Detection Settings.

4.Tap Motion Zones™.

 For full instructions on how to set customized Motion Zones™, see Configuring Motion Zones™.

.

Why am I receiving so many notifications?

There are a few ways you can lower the number of notifications you are getting.

.

How do I enable Color Night Vision?

1.Lauch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap  icon to disable Auto Night Vision.
Note: Disabling Auto Night Vision will force the camera into Color Night Vision mode. Recommended in low-light conditions.

.

How to activate Two-Step Verification?

1.Launch the Lorex App.

2.Tap Settings.

3.Tap Account Settings.

4.Tap Two-Step Verification.

5.Tapicon to enable Two-Step Verification.

For detailed setup instructions, see Two-Step Verification Setup.

.

How to optimize video quality?

1.Launch the Lorex App.

2.Tap  icon above the channel thumbnail on the Devices screen.

3.Tap Video Settings.

4.Tap  icon to enable HDR (High Dynamic Range).

Note: Enabling HDR optimizes video picture in high-contrast conditions such as under-lit and over-lit areas.
By default, the video quality is set to High (2x1080p HD).

.

What is Home & Away™?

Lorex App can automatically use your location to manage your notifications when you are at home or away. The app will notify you when you are inside/outside of your set home perimeter.

To start using this feature, navigate to your mobile device settings and enable Location services for Lorex App.

For detailed setup instructions, see Configuring Home & Away™.

.

How do I activate the LED deterrence light when motion is detected?

1.Lauch Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Deterrence Light Brightness.

4.Tap  icon to enable camera’s deterrence light whenever motion or person is detected.

.

How do I remove the 2K Wi-Fi Camera from my account?

1.Launch the Lorex App.

2.From the Devices screen, tap  icon to configure device settings.

3.Tap Remove Device.

.

How to permanently delete data of 2K Wi-Fi Camera?

Refer to Formatting Device Storage for more information.

.

Does my device support WPA2 or WPA3?

Your device supports Wi-Fi Protected Access 2 (WPA2) which is the industry standard security protocol for Wi-Fi networks. WPA2 offers security against unauthorized access and data interception and is supported by most Wi-Fi routers including those that support both WPA2 and WPA3. It employs Advanced Encryption Standard (AES), an encryption mechanism, which secures communication between your camera and Wi-Fi network to keep transmitted data confidential. For information on which devices support WPA2 and which devices support WPA3, please refer to “WPA2 and WPA3 Supportive Devices.”

.

What are the compatible SD cards?

Refer to Compatible SD Cards and Storage Sizes for more information.

.

What devices are compatible with the 2K Wi-Fi camera?

Refer to Product Compatibility Chart for more information.

W482CAD – 2K Wi-Fi Camera : Installation

This article provides instructions to install your Lorex 2K Wi-Fi camera with Smart Deterrence (W482CAD).

.

What is included in the box?

The above contents are based on one camera.

.

How to connect with Lorex App

3.Open the Lorex App app and create an account or login with your credentials.

4.Tap  icon to add a new device, then follow the in-app instructions to complete the device setup.

For full instructions on Lorex App setup, see Connecting with Lorex App.

.

How to mount 2K Wi-Fi Camera to the wall

.

How to mount 2K Wi-Fi Camera to the ceiling

Wi-Fi Security Cameras – How to Read a MicroSD card

To view the contents of a MicroSD card on a laptop or computer, follow these steps: