How do I integrate Hanwha IP cameras and SUNAPI with Immix?

Summary

This article details the steps to integrate Hanwha IP cameras and SUNAPI with Immix.

Integrate Hanwha with Immix

To begin the integration, a suitable port for Immix must be located.

NOTE: These are default ports only (they can be configured and may be
different to what is listed).

To find ports in Immix:

Configuring Users in Hanwha Vision for Immix

To configure users:

Video Profile

The integration has capabilities to switch between different video profiles. To switch between profiles:

Configuring a Hanwha IPC SMTP Alarm

To configure the alarm into Immix:

S# – represents the ServerID.
A# – represents the Input of Response.
E# – represents the Event Number associated with the Server Type,
e21 is defaulted to IPC Object Detection.

IPC Email Example

Subject: ObjectDetected

Sendor: S29.a1.e21@ImmixAlarms.com To: S29.a1.e21@ImmixAlarms.com

Date: 20240514-12:03:47XMailer:NFMail

https://support.immixprotect.com/hc/en-us/articles/25738891242395-Hanwha-IP-Camera-SUNAPI-Integration 4/7
XMailer: NF Mail MIME-Version: 1.0 Content-Type: multipart/mixed; boundary=594786580.1111.samsungipolis.com –594786580.1111.samsungipolis.com Content-Type: text/plain; charset=”iso-8859-1″ Content-Transfer-Encoding: 7bit ObjectDetected Time : 20240514-12:03:47 Camera IP : 192.168.1.166 Event Type : EventRule_5_CH1 –594786580.1111.samsungipolis.com Content-Type: application/octet-stream; Content-Transfer-Encoding: base64 Content-Disposition: attachment; /9j/4AAQSkZJRgABAQEAYABgAAD/2wBDABQODxIPDRQSEBIXFRQYHjIhHhwcHj0s LiQySUBMS0dARkVQWnNiUFVtVkVGZIhlbXd7gYKBTmCNl4x9lnN+gXz/2wBDARU

Enabling Digest Auth

If you are having trouble using GetConfig, enable Digest Auth for your Hanwha user.

The image below shows where to enable this:

NOTE: Ensure that the user is Admin or Full user permissions. You must
create an Immix user and assign them as an administrator. A default
admin account cannot be used.

Configuring a Hanwha IPC SMTP Event

To configure the system-based events into Immix:

Obtaining the S Number

To obtain the S number:

Configuring Devices within Immix

To configure a device within Immix:

Obtaining the ID of a Camera for Use in the Extra Value

To obtain the ID of the camera:

SSL Error Alarms

By default, the alarm receiver is configured to disallow insecure connections. To allow connections to insecure devices (no SSL, invalid cert, etc.), change the RequireCertificate config key in appsettings.json to false.

Alarms Not Decoding

By default the alarm JSON messages are saved in the file store in the same folder as any alarm footage. To diagnose decoding issues, confirm that this message is what is expected. A typical alarm message looks like the following snippet. Alarm messages always have the broadcastAction alarm.

{
“Tran”: {
“Command”: “broadcastAction”,
“Params”: {
“Params”: “eyJhY3Rpb25JZCI6InthYWNiMjdmOC1lYTcwLTRlOGEtOGE1YS03YjZiNzk5ZTliMGR9IiwiYWRkaXRpb25hbFJlc291cmNlcyI6WyJ7MDAwMDAwM
“RuntimeParams”: “eyJkZXNjcmlwdGlvbiI6Il90aHVtYl9kb3duIiwiZXZlbnRSZXNvdXJjZUlkIjoie2RhZWU5ZWIyLTEyZDYtZTUwNy00Y2MxLWM4ZmUxNG
}
}
}

A second approach is to review the service logs, as all messages (even non-alarm messages) are logged there.

How to use Wisenet cameras with exacqVision

Summary:

This article provides information on using Wisenet cameras with exacqVision.

Step By Step Guide:

Wisenet Camera Settings

Mandatory

The following settings are mandatory:

Optional

The following settings are optional:

After Adding to exacqVision

exacqVision defaults to using the Hanwha default H.264 stream (profile 2) but can be changed to H.265. This changes exacqVision to utilize the default H.265 stream on the camera (profile3).

NOTE: It is not possible to set h.265 via exacqVision on a fisheye camera.
You need to log in to the camera interface and manually change the FISHEYE
profile to H.265.

To change the default stream to H.265:

1.Navigate to the exacqVision Camera Settings page and click the Recording tab.
In the Rate Control field, the default is Constant Quality which equates to Variable Bit Rate in Hanwha cameras.

The Quality slider default of 2 sets a low cap.
1 = minimum VBR cap for that stream
10 = maximum VBR cap for that stream
For 4MP+ resolution cameras it is beneficial to increase the quality to 3 or 4; otherwise, the video may be compressed too much thus decreasing quality.

2.If needed, select a stream to add from the Multistreaming dropdown menu and click Add Stream.

NOTE: With high-resolution cameras, it is best practice to create lower
resolution live viewing streams to save on decoding and bandwidth. These
streams can be added in exacqVision on the Camera Settings page.

3.Click the Motion tab to edit motion on the camera (although exacqVision does not have all the options available that are in the Hanwha cameras).

NOTE: It is possible to add motion, including windows, without adding\
multiple points to create unique shapes.

4.Click the Analytics tab to see several options for displaying and recording data.

5.If the camera is a fisheye, click the Digital PTZ/Fisheye tab to configure the proper dewarp code.
a. Select Immervision from the first dropdown menu.

b. Select the proper code from the second dropdown menu.

Refer to the following article for Hanwha Fisheye Lens Codes: Immervision Fisheye Dewarp Lens Codes

c. Select how the camera is mounted for proper dewarping from the third dropdown menu.

NOTE: Many of Hanwha’s fisheye cameras can use additional camera side dewarp
channels. These should be created first before the camera is added to
exacqVision, so they are identified and configurable inside of exacqVision.
These channels have no motion detection so they either need to record 24/7
or be used for live video only.

NOTE: The Video tab does not exactly match what is in the camera.

Brightness = Brightness
Contrast = Contrast
Saturation = Color Level in the camera
Wide Dynamic Range = controls SSDR in the camera
Video Mask = controls the camera’s Privacy Areas

Searching AI Metadata

To search AI metadata:

1.From the exacqVision home page, click the Search () icon in the top left corner of the screen.

2.Expand the camera tree then select the camera and the analytic metadata associated with it.

3.Select the Search Range to search for then click Search.

4.Click the Paper () icon to view the raw metadata.

A pane to the right of the video will appear with the raw data of that time.

5.Check the Show Filters checkbox to filter data.

6.In the pane to the left of the video, check the checkboxes to filter.

7. Click Save then click the Search button again.

NOTE: Save filters can be selected from the dropdown menu at the top.

8.If certain overlays for the metadata need to be hidden, click the Green () icon and select which overlays should be hidden.

Creating Events Based on Analytics

NOTE: The analytics must be configured in the camera first. Once done and the
camera is added to exacqVision, disable and re-enable the camera.

To create events based on analytics:

Monitoring Analytic Events

To monitor analytic events, follow the steps in the Creating Events Based on Analytics section. However, use Event Monitoring instead of Event Linking.

Special Considerations

Take the following into consideration when setting up a camera:

Optional Common Camera Settings

The following camera settings are optional:

Verint recorders using different FPS for normal and event recording

Summary:

When a Hanwha camera is registered to a Verint NVR, the use of different FPS can be engaged on the NVR

Explanation of Behavior:

Resolution:

• Firmware can be easily updated via the NVRs web interface, the NVRs monitor/mouse interface, Wisenet Device Manager, or Wisenet Viewer. The process takes approximately 5 minutes.

• The way Verint operates is that the recorder will dictate the camera’s FPS, and changing the video profile on the camera, by default, momentarily drops and reestablishs the connections.

How to add a Wisenet camera to Genetec Security Center 5.9

Summary:

This article provides instructions for adding a Wisenet camera to Genetec Security Center 5.9 and the additional steps needed if the camera has a fisheye lens.

Step By Step Guide:

To add a Wisenet camera to Genetec Security Center 5.9:

1.Open Wisenet Device Manager.

2.Double-click your camera to load the camera’s webpage.

3.Enter and confirm your new password, then click Apply.

NOTE: If a password has already been configured and you need to default
the camera, press and hold the Reset button for 5-10 seconds.

.

4.From the Genetec Config Tool application, click the Video icon.

5.Right-click Archiver and select Unit enrolment.

6.Click Manual add then select Hanwha Techwin from the Manufacturer dropdown menu, select Wisenet from the Product type dropdown menu, and enter the IP address of the camera.

NOTE: You can find the IP address of the camera in the Wisenet Device
Manager results screen. Click Add and close to enroll the camera.

TIP: If you see a Bad logon error, move your mouse over the text and an Add button will appear.

Enter the username and password of the camera then click the Add button.

After a few moments the status should change to Added.

.

NOTE: Sometimes the status in Genetec sticks on Bad logon. To resolve this
issue, click Clear All at the bottom of Unit enrollment and add the camera
again. The camera has now been added to Genetec Security Center 5.9.

Configuring a Fisheye Camera

The following additional steps are required if the camera has a fisheye lens:

1.From the Video tab, select the newly added camera under Archiver then click Hardware and edit the Lens type.

2.Select your Camera position from the dropdown menu.

NOTE: Genetec may not automatically pick the correct lens type and
could fail to calibrate.

3.Select the correct Lens Type from the dropdown menu.

4.Click Ok and Apply at the bottom of the page to save changes.
The fisheye camera settings are now complete.

Viewing the Newly Added Camera

To view the newly added camera:

1.Open the Security Desk application from the Windows Start menu.

2.Log in and and select Monitoring.

3.Double-click the newly added camera to see live video.

4.Use the scroll wheel on the mouse or click the Viewing Mode icon to manipulate the image.

Genetec – Adding a Hanwha Camera to Genetec 5.7 or later

Summary:

This article will provide a step-by-step guide for adding a Wisenet camera to Genetec.

Step By Step Guide:

1. Open the Config Tool (Figure 1)

Figure 1

2. Click on the green plus symbol (Figure 2)

3. Select Video Unit (Figure 2)

Figure 2

4. Select Hanwha as the manufacturer (Figure 3)

5. The IP Address can be a single device or a range of devices. (Figure 3)

6. Provide the proper credentials and click “Add and close” or “Add.” Then, repeat for further units. (Figure 3)

Figure 3

7. Once added to the system, you will be able to view the stream from the Video Unit (Figure 4)

Figure 4

How do calibrate a Hanwha Fisheye Camera for use on a Genetec VMS?

Applies to Models: XNF, SNF, and QNF Series Cameras

Summary:

This article describes how to add a Hanwha Fisheye camera to Genetec, by set a lens code and calibrate the camera.

Note: The lens code will be determined by the model.
See this article for a complete list of codes.

Step By Step Guide:

1. Open the Config Tool, go to Video Unit.

2. Select the Video Unit in question.

.

3. Select the Hardware Tab of the Fisheye camera to be configured.

4. Set the Lens Type to Panamorph.

.

5. Click the Pencil to the right of the Panamorph dropdown.

.

6. Set the orientation to either ceiling or wall.

7. Select the proper Lens Type  from the list (See De-warp Code article link below.)

8. Click calibrate once the code is registered.

Note: If it fails check the motion detection tab for an improperly configured Event or
Motion Schedule.

Click here for Immervision De-warping codes

.

<p>The post How to use Wisenet cameras with 3rd party VMS first appeared on NVR IPCAMERA SECURITY.</p>

How to add a Hikvision NVR to Hik-Connect

Before you start…​

Part 1: Enable Hik-Connect on the NVR…​

.

.

.

.

Part 2: Set up Hik-Connect on your mobile phone or tablet…​

.

.

.

Part 3: Add the NVR to your Hik-Connect account…​

.

.

.

Other tips…​

Guides for Hikvision NVRs with V5 firmware

How to set up motion detection and alerts on a Hikvision NVR

What is Motion Detection and why is it useful?​

Motion detection is one of the easiest events to set up and will notify you as soon as a person or vehicle enters a predefined detection zone in your scene. Traditionally, it would just rely on lots of pixels changing between frames in your camera’s video stream, which would indicate movement in the scene.

Of course, this would cause lots of alerts for things you are not interested in, such as animals, moving plants and rain. Hikvision’s Acusense cameras and NVRs now have something called Motion Detection 2.0, which cuts the false-positive detections right down as will only notify you when people and/or vehicles are in the scene by learning what they look like. In this simple step-by-step guide, we will show you how to get motion detection set up on the new NVR 5.0 web interface.

Step 1: Go to your NVR’s Motion Detection configuration page…​

Step 2: Configure your Motion Detection zone and rules…​

​

Quick tip…​

If you find that the camera preview is too small when drawing your detection zones, you can switch the view to full screen by clicking on the Full screen (four arrows) button in the toolbar, and then exit full screen by pressing Esc on your keyboard.​

Step 3: Set the arming schedule to specify when you want Motion Detection active…​

​

Quick tip…​

If the 30-minute segments are not precise enough for you, you can finely tune a period of arming or disarming by double-clicking on the segments and specifying your start and end times in minutes using the arrows.​

​

Step 4: Set what you need the NVR to do when a camera detects a target…​

How to connect an IP camera to a Hikvision NVR

Adding cameras to your Network Video Recorder (NVR) is a crucial step in any CCTV setup. Not only does it allow you to store and access all your camera recordings in one place, but it also simplifies camera configuration. In this simple step-by-step guide, we’ll show you how to add cameras to a Hikvision NVR using the new NVR 5 web interface.

.

Why add cameras to an NVR?​

.

Before you start…​

Before anything, to be able to add your IP cameras, you need to make sure that:
.

.

How to add your cameras using the V5 GUI…​

Step 1:​

Open a web browser and enter the IP address of your NVR in the address bar. If you are not sure what this is, use the SADP tool to find it.​

Step 2:​

Log in to the NVR using the “admin” username and password you have set on it.​

​

Step 3:​

Go to: Device Access > Device Configuration > PoE Settings​

​

If you are connecting your camera via the Plug-and-Play method, then make sure that Network Camera Plug-and-Play is enabled on the POE port you will be connecting the camera to on this page.​

​

For any camera with a cable run under 100m, leave the Network Cable Distance as Short Distance.​

​

If you are connecting your camera manually by IP address, disable the Network Camera Plug-and-Play option for the channel that you plan to add the camera to.​

Step 4:​

Go to: Device Access > Device > Video Device​

​

For any Plug-and-Play camera, just make sure that it is in its inactive default state and then connect it to the port you reserved in step 3. After 20 seconds or so, the camera Status should turn to Connecting and then Online (you may need to click on Refresh to see this).​

​

For Manually added cameras, if you can see the camera in the List of Online Devices section, then just tick the box for the camera and then click + Add to Device List, which will then automatically add it to one of the channels you disabled Plug-and-Play on in the last step.​

Alternatively…​

Click on +Add at the top of the page and fill out the fields as follows:​

​

IP Address: Enter the IP address of your camera, using the ‘Test’ button to verify there is a camera at that address. ​

Device Name: This can be anything you like, as it is the name the camera will show with on your NVR. ​

Protocol: Select the camera’s manufacturer from this list, or failing that, use the ONVIF protocol (your camera will need to have ONVIF enabled for this to work). ​

Management Port: Enter the Server port set on the camera, which you can find in the SADP tool or in Network>Basic Settings>Port in the camera’s web browser interface. If you haven’t changed this, it is usually 8000 by default. ​

User Name: “admin” or the username of any other users set up on that camera. ​

Password: The password set with that user on the camera – if this is the same as the ‘Default Activation Password‘ you have set on the NVR, then you can tick this box instead. ​

Transfer Protocol: ‘Auto’ is normally best. ​

​

When these are completed, click OK.​

​

Your camera should then appear in the list of devices with an assigned channel, and an Online status, meaning it has been successfully added.​

.

Extra tips…​

Source : https://www.use-ip.co.uk/forum/forums/guides-for-nvrs-with-v5-firmware.71/

.

<p>The post Guides for Hikvision NVRs with V5 firmware first appeared on NVR IPCAMERA SECURITY.</p>

Our products and solutions have been deployed and used daily in more than 100 countries and regions, meeting customer needs in various vertical markets that range from residential to commercial, from healthcare to public safety.

Reset Device Web Password on Akuvox Cloud Platform

Users may forget passwords for logging into device web interface. Follow the steps to reset the web password when the device is connected to Akuvox Cloud.

Step 1

Log into the Akuvox Cloud platform with an installer account.

Step 2

To go to the device Info page, follow the steps.

On the Single-tenant Manager view

1. Click User on the left column.

2. Click the Device icon of the desired user.

3. Click the Info icon of the desired device.

On the Project Manager view

1. Select Community or Office on the left upper corner.

2. Click the Info icon of the desired community or office.

3. Click Intercom Devices and then the Info icon of the desired device.

Step 3

1. On the device Info page, click the Settings button.

2. On the Settings page,

Note

Factory Reset Akuvox Devices v2

Reset Door Phones through Physical Buttons

Note

Power up the devices before resetting them through the physical buttons.

S539, S532, X916 and X912

Hold the reset button with a pin and the device will be reset.

X915, E12 and DB01

Insert a PIN into the hole and hold it to reset the device.

E16, E18, E20 and E21

Remove the back cover of the door phone and hold the reset button to reset the device.

R27, R28, R29 and R20 Series

R27, R28, R29, and R20 series do not support resetting by pressing physical buttons.

Watch the video for other reset methods.

Reset Intercom 2-wire Kit Accounts for Single Tenants

Through resetting, the tenant information will be deleted while the device information will be retained after a tenant moves out. This saves time from repeatedly entering the device information.

Installers

1.Log into the SmartPlus Cloud platform with an installer account.

2.Click Role in the upper right corner to switch between single-tenant and community projects.

3.Click to reset the target user account.

After resetting, the following data will be reset:

The following data will be kept:

The following data will be removed:

Distributors

Distributors can reset the Kit users when the Kit is added directly to the single-tenant projects under the distributor account.

3.Click  to reset the target user account.

After resetting, the following data will be reset:

The following data will be kept:

The following data will be removed:

End Users

End users can delete the family master account on the indoor monitor.

After resetting, a new QR code will be issued to the indoor monitor from the SmartPlus Cloud.

On the SmartPlus Account screen, tenants can scan the QR code to register SmartPlus accounts themselves.

.

How to Configure and Modify the Password

The initial password “admin” is rather weak, easy to crack, thus we provide for you the password change service.

Before Start

The difference between the user mode and admin mode on the web page

How to configure

Website password modification

admin mode
Go to Security >Basic >Web Password Modify, choose user name as “admin”, click Change Password, then enter the old password “admin”, input the new password.

user mode
Go to Security >Basic >Web Password Modify, click Change Password, then enter the old password “user”, input the new password.

Device password modification

System code
System code is used to enter “More Interface”, to adjust the password: More>Settings>More, input the default system code “123456”, tap System Code, input the original system code and new system code.

Setting code
Setting code is used to enter “Settings”, and it is left blank by default. To adjust the password: More>Settings>More, input the default system code “123456”, tap Settings Code, leave the original settings code blank, input the new one.

Steps to Enter Device Web Interface

.

Factory Reset Akuvox Devices

Reset Device Web Password on Akuvox Cloud Platform

Users may forget passwords for logging into device web interface. Follow the steps to reset the web password when the device is connected to Akuvox Cloud.

Step 1

Log into the Akuvox Cloud platform with an installer account.

Step 2

To go to the device Info page, follow the steps.

On the Single-tenant Manager view

1. Click User on the left column.

2. Click the Device icon of the desired user.

3. Click the Info icon of the desired device.

On the Project Manager view

1. Select Community or Office on the left upper corner.

2. Click the Info icon of the desired community or office.

3. Click Intercom Devices and then the Info icon of the desired device.

Step 3

1. On the device Info page, click the Settings button.

2. On the Settings page,

Note

.

Check IP Address of Akuvox Door Phones

IP address(es) can be obtained on Akuvox door phones. With the IP address, you can log into the device web interface for configuration, troubleshooting, and more.

Devices with Numerical Keys or Touch Screens

Check the IP address on the system information screen.

Devices without Numerical Keys or Touch Screens

Check IP address through automatic IP announcement.

Note

You can also obtain the device’s IP address using the Akuvox IP scanner.

Download IP scanner:
https://knowledge.akuvox.com/docs/akuvox-ip-scanner?highlight=IP

Check IP Address of Akuvox Indoor Monitors

IP address(es) can be obtained on Akuvox indoor monitors. With the IP address, you can log into the device web interface for configuration, troubleshooting, and more.

The routes may vary by model.

In this part, C313 is taken as an example.

Exception

To check the IP address of S560, press the # key for about 5 seconds and the device will automatically broadcast its IP address.

Check IP Address of Access Control Terminals

Obtain IP Address via IP Scanner

IP scanner allows you to search the device IP address(es) and to perform targeted device reboot, reset, network setting, etc.

Note

Installation

1. Decompress the rar. file downloaded.
2. Double-click on the setup.exe file.

3. Go through the installation process.

a. Click Next to start the installation.

b. Check to accept the terms of the license agreement, and click Next.

c. Enter User Name and Company Name, and click Next.

d. Click Finish to install the IP scanner successfully. The software icon will appear on the desktop.

Obtain IP Address

Note

To obtain the device IP address, your personal computer should be in the same LAN as the device.

Additional Features

Apart from checking IP address(es), you can export device information and perform targeted device network settings and web interface access, reboot, and reset.

Note

Before applying the following changes, enter the User Name and Password. The default is admin.

Log into Device Web Interface

Enter the device IP address in a browser, and you can log into the device web interface for configuration, troubleshooting, and more.

.

<p>The post Factory Reset Akuvox Devices v2 first appeared on NVR IPCAMERA SECURITY.</p>

Troubleshoot Offline Camera

Troubleshoot Offline Camera

Learn how to troubleshoot when a new Verkada camera is offline

Updated over a week ago

Use this article to read through some common scenarios and try the suggested troubleshooting tips to help. If you still need help, please contact Verkada Support.

What is the LED status of the camera?

Camera has been solid orange for over 10 minutes

Camera is blinking blue for over 5 minutes

Camera is solid blue for over 5 minutes, says “waiting to be connected on Verkada Command”

Roles and Permissions for Cameras

Roles and Permissions for Cameras

Learn about the roles and permissions available for Verkada Cameras

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Cameras.

Org-level roles

Organization-level roles are configured on a per-user basis. Groups cannot be used to set organization-level roles.

Below, click the down arrow to the left of the role to learn more about the role and access.

Org Member

Org Admin

Verkada Cameras Troubleshooting 2024

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

CP52-E PTZ permissions

The CP52-E PTZ camera permissions determine who can manage the Sentry Mode feature.

Permissions model (example)

Here’s a simple example of a permissions model that a typical organization with several sites and users may employ:

Users and their required level of access

Permissions each user should be assigned

.

Set Org Admin permissions

Revoke Org Admin permissions

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Customize roles and permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

Roles and Permissions for Command

Roles and Permissions for Command

Learn about the roles and permissions available to Command users and groups

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Command. It also explains how to customize roles and permissions.

Permission levels

Permissions are set at the following levels:

Daha fazla göster

Permissions considerations

Common user permission configurations

Daha fazla göster

Roles and permissions by Verkada product

.

Org-level roles

Org-level roles are configured on a per-user basis. Groups cannot be used to set org-level roles.

Org member

Org Admin

Access Control Role

.

Site-level roles

Site-level roles can be assigned to individual users or to groups and pertain to a specific site or subsite. Subsites inherit the permissions from the subsites and parent sites above them.

No Access

Site Live-Only Viewer

Site Viewer

Site Admin

Access Site Admin

.

Customize Roles and Permissions

Verkada’s Roles & Permissions Customization feature enables Org Admins the ability to add or remove certain permissions from Site Admins and Site Viewers more granularly. Some organizations may want to limit or extend the permissions of the members of their organization based on their needs. Currently, we allow customization of permissions related to archives, link sharing, and user management.

FAQ

Why has my organization disappeared?

Why are cameras missing from my organization?

Why can’t I access certain features or settings, such as other users?

Resolve Issues with Missing Cameras

Resolve Issues with Missing Cameras

Learn how to resolve issues when cameras are missing from your Verkada account

Updated over a week ago

When you log in to Verkada Command, you can only access cameras and video in organizations or sites where your user account has permissions.

Note: Even if you are an Org Admin, you still need to grant yourself permission to view all sites. Learn more about roles and permissions for cameras and Command.

If you log in to Command and cameras are missing or have disappeared, always check user permissions. The most common reason cameras are not visible is that your user account needs permissions to the site(s) where the cameras are configured.

Common reasons that can cause cameras to disappear

Check permissions

If you are an Org Admin, you can check and correct your own permissions:

Resolve Issues with Night Mode

Resolve Issues with Night Mode

Common issues with IR and Night Mode with steps to resolve them

Updated over a week ago

Each Verkada camera has night vision capabilities, using a sensor to detect low-light situations. When external lighting is low, the camera switches to night mode and records in black and white, using infrared (IR) LEDs to illuminate the environment. If the IR is emitted improperly through the dome or reflected into the lens, it negatively impacts image quality.

Common night mode issues

It is imperative that the dome remain free of debris and the camera is installed properly to achieve the best image quality. When viewing footage in night mode if the footage appears obscured it is most likely the result of one of the following scenarios:

Camera always in night mode

If your camera is always in night mode even where there is sufficient light in the environment the lux (light) value may need to be adjusted. If this is the case, reach out to Verkada Support for further assistance.

Environmental obstruction

If the camera is mounted too close to a wall, ledge, or light source, the image quality may be degraded due to IR reflection.

Recommendation. Ensure that cameras are mounted sufficiently far away from surfaces that may cause the IRs to reflect, such as light sources.

IR obstruction

If a first-generation Dome camera (D30 or D50) is operating in night mode when there is plenty of light, the IR sensor is likely obstructed by the camera housing.

To fix the obstructed light sensor, physically rotate the lens barrel assembly 180° so the sensor and IRs are visible through the camera case.

Example: Proper and improper orientation

Note: After rotating the lens barrel, the camera orientation may need to be changed in Command.

<p>The post Verkada Cameras Troubleshooting 2024 first appeared on NVR IPCAMERA SECURITY.</p>

Tapo was created to engage in the small intelligent appliances market, to help people adopt a new smart home lifestyle at an affordable cost. That’s why we insist on Smart, Easy, Secure.

.

What should I do if I fail to configure the Tapo Smart Plug?

The Tapo app will guide you step by step during the initial configuration, but you may not be able to get through all the steps due to some interference. This FAQ will tell you what to do if you have trouble getting through a certain step.

Case 1

The phone is looking for the smart device via Bluetooth or its default 2.4GHz WiFi, if you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

Tapo Smart Camera FAQ v1

Case 2

If you are unable to find your home Wi-Fi network, please refer to the following suggestions.

Troubleshooting tips:

1. The signal strength of your home Wi-Fi network is a bit weak, move the smart device closer to your router for a try.

2. Ensure your home Wi-Fi network is a 2.4GHz Wi-Fi network, the Tapo device does not support a 5GHz Wi-Fi connection.

3. If it doesn’t display the Wi-Fi name of the router automatically, please click on “RECAN” at the upper right corner to refresh the Wi-Fi list.

4. If the router’s SSID is hidden, please choose “Other” to input SSID and password manually.

5. Please change the wireless channel of the 2.4G Wi-Fi network to 1, 6 or 11.

6. Reset the device as per QIG/UG and go through the process again.

Case 3

If you are unable to get through this step, you will see the following error page.

Troubleshooting tips:

1. Ensure you have selected the correct home Wi-Fi network and have entered the correct wireless password. If the Wi-Fi network or password is incorrect, click on “Choose a Network” and select the Wi-Fi network again.

2. Make sure your smart device is within the Wi-Fi range of your router.

3. Turn your phone’s or tablet’s Bluetooth off and back on.

4. If the problem persists, try to reset the smart device as per UG/QIG, and then set it up again.

5. Check if there is a firewall on your router. If yes, please turn it off.

6. Change the wireless security type of the 2.4G network to WPA2.

7. Try to connect the Tapo plug to the hotspot of your cell phone or another wifi network. If it works, please upgrade the firmware for the plug, then reset and reconnect it to your router.

.

What features does Tapo smart plug and Tapo smart switch support?

Currently the Tapo plug and switch supports the following features:

.

How to view Tapo camera on PC/NAS/NVR through RTSP/Onvif Protocol

The Tapo camera supports the RTSP and Onvif protocol, so it can work with third-party NVR or NAS devices that also support the RTSP/Onvif protocol. If a user wants to view the live stream of the camera with a third-party app like VLC Player, iSpy, here is the method for him.

Notes:

1. The username/password is the camera account that you created via the Tapo app. If you haven’t created the username and password, please follow the instruction of Step 1 in this article.

2. The IP address is the camera’s IP address assigned by your host router. You can find it on your host router’s DHCP list or in the Tapo app (Go to the Device Settings page of the camera and tap Device Info to see its IP).

3. If you want to view the live stream of the Tapo camera with a third-party app remotely, you will need to open port 554 for the camera on your host router first. Please enable the TCP forwarding for port 554.

4. You could use ONVIF standards to add the Tapo camera with its username/password and IP address. Please see the example of iSpy in Case 2 to know how to use onvif protocal to control the camera.

5. For Tapo C310, the resolution of the stream1 is determined by the video quality set on the Tapo APP.

If you need to watch the 3MP HD Video via RTSP, please change the video quality to Best Quality on the Tapo APP and use: rtsp://IP Address/stream1

6. If the Camera is inserted microSD card and subscribed Tapo Care, its RTSP stream will fail. You need to remove microSD card or cancel Tapo Care to get its RTSP stream.

7. If you find that there’s no or very little sound when using RTSP/Onvif to watch live stream, please adjust the camera microphone on Tapo APP.

Apart from the Tapo app, Tapo cameras can work with other third-party software to use and manage your Tapo camera.

Note: Before you start, make sure the computer/NAS/NVR and your camera are connecting to the same network or can visit the public IP and port of your camera.

Step 1: Create a camera account in the Tapo app

1. On the Home page, tap on your camera model card to go to the camera Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Advanced Settings, then select Camera Account to create an account (username and password) for camera login on other portals.

You will see a prompt like below (About Camera Account), please read it and tap Understand and Agree to Use, then you can create an account for the camera.

Note: The username and password should contain 6 to 32 characters.

Step 2: Add your Tapo camera on iSpy (Example of Onvif protocol connection)

1. Run the iSpy software on your computer.

2. Click Add on the top left menu and select ONVIF Camera.

3. Enter the Username and Password that you set for your camera on the pop-up window, select Network Address, and click Next. You can customize other parameters if needed.

4. Choose the video resolution and click OK.

5. Customize the camera settings as needed, including Microphone, Talk, Motion Detection, Alerts, Recording, Images, Scheduling, and Storage. You can also change all the settings later. Click Finish to complete adding your camera to iSpy.

6. After adding your Tapo camera to iSpy, you can monitor and manage it using the app. View the live, customize motion detection, check the recordings when motion detected, set recording schedules, record videos and more.

Step 3: Watch your Tapo camera on VLC (Example of RTSP protocol connection)

1.Open the VLC software, select Media > Open Network Stream

2.Fill in the URL of the Tapo camera

The URL of the RTSP live stream for the Tapo cameras will be:

For high quality stream1: rtsp://IP Address/stream1

For low quality stream2: rtsp:// IP Address/stream2

In some software, the URL need to add the port to access live stream, the default port is 554:

For high quality stream1: rtsp://IP Address:554/stream1

For low quality stream2: rtsp:// IP Address:554/stream2

If you fail to stream the Tapo camera via the RTSP/ONVIF protocol, you may refer to the article for the troubleshooting:

https://community.tp-link.com/en/smart-home/forum/topic/652710

To get to know more details of each function and configuration, please go to Download Center to download the manual of your product.

.

How to factory reset the Tapo or Kasa smart plug

.

To restore a Tapo or Kasa smart plug to its factory default settings and re-enable the setup mode, please press and hold the power button for 10 seconds.

The LED status for a factory reset varies by model:

After a completing the reset, you can then connect and configure the device in the Tapo App.

How to avoid noise when monitoring the sound from Tapo camera

Tapo cameras are capable of not only monitoring video stream from the camera, but also monitoring sound collected by the built-in microphone on the cameras. You can turn on/off the sound feature like the monitor screen as below. But to increase or decrease the volume, you need to press the volume button on your phone.

Why is there noise?

Noise is a physical phenomenon and it’s actually inevitable. Basically, the IP cameras including other brands’ have background noise more or less. And those cameras which seem to generate less noise probably have worse sound collecting performance. Tapo cameras are designed with a sensible sound collector which might take some noise in your monitor. Even though it is inevitable at present, we are still trying our best to make improvement and searching for better solutions.

How to reduce the noise?

1.     Please keep your mobile device away from the camera as much as possible. The Tapo camera is designed for remote access and monitoring via cloud service, local usage in close range may cause interference and noise between your mobile device and the camera.

2.    Please reduce the output volume below 50% since a louder volume may enlarge noise decibel. The value between 40%-50% is suggested with not only good sound quality but also minimum noise decibel. As long keep focus on our cloud camera you will find our progress on new models.

Your understanding is highly appreciated!

How to edit Home and Away Mode for Tapo&Kasa Cameras on the Tapo app

.

The Away mode and the Home mode are two different sets of Detection, Alarm, and Notification settings for Tapo&Kasa cameras. You can tap the button on the Tapo app>Cameras tab to quickly apply the preset settings to the cameras when you are home or away.

Note:

Here we take the Home Mode as an example.

For Tapo Cameras:

1. Open Tapo APP, find the Cameras tab at the bottom, and locate the Detection Mode section.

You can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three-dots option.

2. Click on Add Devices if you want to add more cameras to the Home mode.

Click on the Edit icon at the top right corner if you want to delete cameras from the Home mode.

3. Select the camera you want to edit the mode settings. Here we take Tapo C200 as an example, and you can change the Privacy mode, Detection, Alarm, and Notification settings of the camera.

Take the Motion Detection feature as an example. You can click on Motion Detection to turn it on or off, change the Motion Sensitivity, and set the Activity Zones on the Motion Detection page.

And you can also click on Detection>Person Detection or Baby Crying Detection to turn them on or off, and tap Alarm and Notifications to configure the related settings.

4. Click on the Back icon at the top left corner of the Tapo C200 page if you have changed the configurations, and click on other cameras if you want to change their configurations.

After completely presetting the Home or Away Mode, you can tap the Home mode or Away mode card on the Tapo app>Cameras tab to switch your cameras’ settings quickly.

For Kasa Cameras:

Here we take KC115 as an example.

1. Open the Tapo app, find the Cameras tab at the bottom and you can tap to activate the Home or Away mode, which will overwrite the current settings of all cameras. To edit the mode settings, click the three dots option.

2. Select the camera you want to edit the mode settings and enter the Detection & Alerts page.

3. You can change the Privacy mode, Detection, and Notification settings of the camera.

Tap Detection > Motion Detection to edit the motion detection function. You can adjust Motion Sensitivity.

Tap Detection>AI Detection to change your AI Detection feature, such as Person Detection.

4. After editing the detection settings, tap Detection & Alerts > Notifications to customize its current settings.

After completely presetting the Home or Away Mode, you can tap the card on the Tapo app>Cameras tab to switch all of your cameras’ detection settings to the mode you want.

.

How can I find the IP address of my Tapo&Kasa camera

Note: Some Tapo battery cameras or doorbells need to work with the hub and can’t connect to the router directly, which do not have IP address.

There are two methods to find the IP address of the camera.

Here we take Tapo C200 as an example.

Method 1: Via Tapo app

1. On the Tapo app> Home page, tap your camera model card to go to the Live View page (or you can click on Cameras tab>tap Manage on your camera model to go to the Live View page).

2. On the Live View page, tap the icon at the top right corner to enter the Device Settings page.

3. Tap Device Info and then you can find the IP address of your camera.

Method 2: Via the web management page of your router

Here we take the TP-Link router Archer C7 as an example.

1. Log in to the management page of your router.

2. Go to Advanced > Network > DHCP Server and locate the DHCP Client List section to find the IP address of your camera.

How can I view continuous recordings of Tapo&Kasa cameras on the Tapo app?

This article will show you how to view continuous recordings on the Tapo app.

Note:

For Tapo Cameras

Here we take Tapo C200 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

Click on Recording Schedule to see the detailed recording schedule settings.

Tap Edit on the Recording Schedule page if you want to change the Continuous Recording and Detection Recording schedule.

And please tap the tick icon at the top right corner to save your changes.

Step 3.

On the camera’s Live View page, tap Playback & Download, select the SD Card icon on the Playback page, select the date, and then you can drag the timeline to view the continuous recordings.

For Kasa Cameras

Here we take KC115 as an example.

Step 1.

On the Home page of the Tapo app:

Step 2.

On the Live View page of the camera, tap Playback & Download > Playback to view all recordings. Drag the timeline and you can view recordings whenever you want and wherever you are.

What can I do if the video image is upside down on my Tapo&Kasa camera

Tapo&Kasa cameras support the function of Video Rotation, and if the camera video image is upside down on the Tapo app, please refer to the following steps to correct it.

Here we take Tapo C200 as an example.

1. On the Home page of the Tapo app, tap your camera model card or tap the Cameras tab>click on Manage on your camera model to go to the Live View page.

2. On the Live View page, tap the icon on the top right corner to enter the Device Settings page.

.

What can I do if I can’t find my Tapo camera on Tapo APP?

If your device does not appear on your app after completing the configuration process, please try the following troubleshooting suggestions:

1. If you are using a Wi-Fi wireless configuration to connect your camera, please check if the camera has successfully connected to the router. You can verify whether the camera is connected to Wi-Fi by checking the System light of your camera. For most Tapo Cams, if it is not connected properly, the LED light will blink red slowly. For the HomeKit version Camera, its LED light indicator will blink blue slowly. If the camera cannot connect properly, we recommend resetting the camera to factory default settings as per the User Guide and then reconfiguring the camera.

How to reset my Tapo camera

2. Check the DHCP settings on your router and ensure that the DHCP Server of your router is enabled. If the camera has already connected to the router properly, you will see the device in the client list of your router. If you don’t know how to do this, please contact your router’s customer support.

3. Please verify if there are any special symbols in your Tapo account（TP-Link ID） password. If there are, try to remove them and make the account password simpler by only using numbers and English letters. Then reset and add the camera from the beginning again.

4. Connect your smartphone to the same Wi-Fi network as your camera and check whether you can see it on the Tapo app. If you can see it, that means the camera fails to connect to the cloud for unknown reasons and you cannot access it remotely. In this case, verify if any firewall or security settings are blocking the connection to the Cloud Server. Temporarily disable any antivirus, firewall, or security software to see if it resolves the issue

.

5. Using a public DNS server may improve the connection, try changing your router’s DNS server settings to 8.8.8.8. If you don’t know how to do this, please contact your router’s customer support.

To eliminate potential issues with the router’s Wi-Fi network, it is recommended to use a mobile hotspot and configure the Camera to test its functionality.

Here are steps for using a mobile hotspot to test the Camera’s configuration:

Preparation: We suggest having two phones. Use one phone (Phone A) to create a hotspot and use another phone (Phone B) to download the Tapo app and complete the setup process.

Steps:

1. On Phone A, disable Wi-Fi and enable only mobile data.

2. On Phone A, navigate to phone settings and access the “Personal Hotspot” or “Mobile Hotspot” option, ensuring that the “Mobile Hotspot” feature is activated. Please make sure the created hotspot operates on a 2.4GHz network.

3. Set a unique name and password for the hotspot, different from your router’s Wi-Fi, to facilitate the Camera’s connection.

4. On Phone B, download the Tapo app. Follow the app’s instructions to add the device and complete the remaining setup steps as guided by the app.

Please contact TP-Link technical support with the following information if the issue persists after the above suggestions.

1) Your TP-Link ID or cloud account.

2) The model number of your TP-Link Cam and its MAC address.

3) The model number of the host router.

4) Whether you have tried all the suggestions listed above or not. If yes, what are the results?

<p>The post Tapo Smart Camera FAQ v1 first appeared on NVR IPCAMERA SECURITY.</p>

TetherX Camera Setup Guide v2, Tether your video surveillance, alarm panels, network infrastructure and other IP or Serial devices to the cloud. Monitor the health of your sites, cloud record cameras and integrate with third party services.

The steps required to set up Samsung Cameras / DVRs and NVRs

Setting Correct Profiles

Please ensure you have 2 profiles configured on your device:

IP Cameras

Cameras are the easiest to set up and should work out of the box. If the cameras are not working for any reason, please try one of the following for the Analytics Path and Recording Path:

Multi-Sensor IP Cameras & Encoders

If your device is a multi-sensor camera or an encoder, please set the Analytics Path as follows:

NVR – Network Video Recorders

DVR – Digital Video Recorders

DVR recorders setup is similar to NVR setup with the following differences:

.

Can I use TetherX alongside HikConnect?

Can I use Hik-Connect on my Hikvision cameras and recorders?

Yes.

Please make sure that stream encryption is switched off under Configuration > Network > Advanced Settings:

HikConnect stream encryption uses a proprietary mechanism which is not available to third-parties. Please note TetherX will encrypt the stream to the highest standards, for more information please see our security white-paper.

Note: If you are still getting a broken stream or no live view, please try updating the camera and/or recorder firmware to the latest. There are known issues that have been addressed by Hikvision.

.

Live View – Technical Implementation Details

How TetherX implements live view to be compatible with all manufacturers

Introduction

The quality, latency and smoothness of live view streaming is dictated by many factors:

Available Streams from Cameras

Typically cameras will provide 2 video streams as well as the ability to request a single image. These limitations dictate what is and isn’t possible when it comes to both recording and streaming.

💡 Note: More expensive and speciality cameras will provide additional video streams and custom streams of crops/de-warps of the same image (e.g. 180 or 360 cameras).

The streams are usually accessed through RTSP and the images through HTTP. For example:

Formats

Transcoding vs Proxying

TetherX supports both transcoding and proxying/packaging. The differences between the two are as follows:

Transcoding is a process of taking the stream from a camera, decoding it and then re-encoding it into a different format. This is the ideal method to hit a specific requirement of Internet bandwidth and viewing size, but it is in most cases cost prohibitive as you need power hungry and expensive hardware to achieve.

​For context, a TetherBox Pico capable of recording 10 cameras will only be able to record 2 if transcoding (you can enable transcoding in TetherX by editing a camera and switching to the advanced tab).

Proxying & Packaging is what is used in most cases, where the original video stream is maintained but is packaged into different containers, for example .mp4 for video recording and .ts for local and high-def live streaming (see streaming technologies below).
​

This means that ultimately, you are at the mercy of the camera/recorder. If you need to open 16 cameras and each one is 1mbit, but your upload speed is only 10mbit, it will simply not work because the stream size cannot be adjusted without either:

Video vs Images

TetherX use a combination of images and video to achieve different goals. It is important to understand the differences and advantages/disadvantages of each, which in turn dictate when either is used in TetherX.

The main difference between image and video compression is every image is self contained, where every video frame is part of a stream. While you may skip an image, skipping a frame in a video stream leads to parts of the image breaking / disappearing:

Systems that ignore broken/skipped data (e.g. streaming over UDP) will show a broken image while many systems will simply show a loading spinner while they wait for the next key frame (which is controlled by the key-frame interval set on the camera/recorder, typically set to 1 second, or the same number as fps, but sometimes much longer).

Because each image is self contained, it is typically 5 to 25x larger in bitrate vs video at 25 images per second. It may initially seem obvious that video should be used when accessing remotely, however there are certain important underlying trade-offs that make it a much tougher question which needs to be evaluated on a case by case basis, according to the following:

Advantages of Images

Live View Streaming Technologies

TetherX uses all mainstream streaming technologies available and choses between them depending on the specific requirements and constraints:

How TetherX Does It

TetherX supports most streaming technologies and switches between them depending on context.

When local streaming (the TetherBox is able to detect if you are on the same network), if we are viewing less than 10 cameras simultaneously TetherX switches to LHLS (see above) to show the primary video stream from each camera at full resolution/frame-rate (assuming your viewing device is capable of displaying this many streams). If this is not working well for you, you are presented with a toggle to switch off High-def streaming to fall back to loading images.

When full screening a camera (double tap/click a camera), we assume you want the higher quality and we switch to the full primary stream. If your connection is not able to sustain this stream, we automatically fall back to loading images.

When viewing multiple sites / cameras over Internet in record mode, we switch to image viewing but we transcode/transize the images depending on the size of each live view box on your screen. This ensures that you are able to view many simultaneous cameras, the latency is lower than video, it automatically adapts to the available bandwidth and it does not impact recording quality. This does however mean a lower fps.

When viewing multiple sites / cameras over Internet in monitor mode, we proxy the connection directly to the image provided by the camera. This leads to a further lowering of fps but ensures the TetherBox can monitor the health of and provide live view of 10x more cameras than in record mode.

Learn more about using Live View in TetherX here.

How Hikvision iVMS Does it

Because of the constrains outlined above, in order to show smooth video in iVMS (and Dahua PSS) software, if the connection speeds both on site and viewing device cannot accommodate the streams, the software temporarily reconfigures the cameras to send a lower bitrate stream while keeping the resolution the same.

💡 Note: if you happen to kill the software at this point (or lose connection), this can cause the camera to permanently record in lower quality.

Because many cameras or recorders only support a single stream at above D1 resolution, this means that not only is the live view quality reduced, but also the video being recoded which can lead to losing critical video evidence.

In our testing, limiting the connection to 5mbit 200ms upload and streaming just 4 cameras in HD resulted in blocky and usable footage being recorded on the NVR. It also took over 10 seconds to get an initial image, however the motion was smooth (25fps) once loaded.

In comparison when using images (outside of the iVMS/PSS software), the images loaded almost immediately, the image quality was significantly higher, but the frame-rate was poor (3-4fps) – still sufficient for making decisions in a control room setting, but understandably disappointing in smoothness by comparison. (Note: higher fps can still be achieved by full screening a single camera on demand).

When viewing a smaller number of cameras from the same manufacturer on a single PC or phone, it looks impressive to have smooth 25fps video on iVMS/PSS/others. However, when dealing with 100+ or even 32 cameras, from different manufacturers, different firmware versions, with multiple users, across multiple sites, with differing and fluctuating bandwidths, you begin to appreciate the trade-offs and advantages/disadvantages of each approach.

💡 Note: This approach of custom code to adjust Hikvision camera settings to achieve smoother live view is only suitable if you do not care about recording quality and you are optimising for a single manufacturer with compatible models/firmware.

​TetherX is an open platform with a focus on convention over configuration, we prioritise the integrity of recorded footage above live view and we implement approaches that work across all recorders/cameras as well as viewing devices.

.

Uniview / UNV Camera Setup Guide (for use with TetherX)

Using TetherX with Uniview / UNV Cameras

Summary

Uniview or UNV cameras should work out of the box in most cases. However please note depending on the age of the camera and firmware versions, the RTSP path may be different.

Please try the following paths:

3. Open the Advanced tab and enter the required Analytics Path and Recording Path. Please try all the paths given as examples above.

.

Camera Setup Checklist

Adding IP cameras to TetherX Please note your camera may have a different interface and options may be located in a different part of the interface. Please refer to the camera manual if you are not able to find the relevant option.

Network

Set a Static IP

Set camera to unused IP on 192.168.88.x network
set DNS/Gateway to 192.168.88.100

Important: Although it’s possible to configure your camera with DHCP, and TetherBox is capable of detecting any IP changes, we strongly advise against this practice for security reasons. This setting can potentially allow the camera to connect directly to the internet, raising a range of security issues. These include unauthorised access through back doors, or the risk of security holes in the camera’s firmware if it’s not updated regularly.

Video & Audio

Recording Stream (primary)

Analytics Stream (secondary)

Conditions

.

Audio (optional)

Date & Time

One option is to disable time from being displayed in the camera at all. You generally do this under OSD settings. If you do wish time to be displayed in the image, you need to set the following:

<p>The post TetherX Camera Setup Guide v2 first appeared on NVR IPCAMERA SECURITY.</p>

By downloading the firmware from this web page you are agreeing to Hikvision’s Software User License Agreement. Please be aware that Hikvision products are region-specific and regionally supported. If you have purchased your Hikvision products from an online source or unauthorized distributor, they may not be compatible with the North American region’s firmware and are considered to be “gray market” product. If your camera has “CH” in the serial number, you are most likely using a “gray market” product. 

Updating the firmware from this site can lead to several complications in those cameras, up to and including camera failure.  Restoring a “gray market” product to its original condition is a factory process and will result in a Chinese interface. As Hikvision warranty is void in this case, you must rely on the dealer for any service, support, and warranty of the “gray market” product. If you have any questions or concerns about the official status of your Hikvision distributor, please contact Hikvision USA Customer Service at cust.usa@hikvision.com.

.

Upgrade Device Firmware

For a device added via IP/Domain, its new version can be detected by the Mobile Client. Once detected, you can upgrade the device to its latest version.

1.Enter the Device Information page.

• On the device list page, if the page is in the list mode, swipe the device name to the left and tap .

• On the device list page, If the page is in thumbnail mode, tap the device name or tap .

• On the Live View page. Tap  and then tap Settings.

Note:

For details about how to enter the Live View page, see Start and Stop Live View.

2.Tap  > Device Version to enter the Device Version page.

3.Tap Upgrade and then tap UPGRADE on the pop-up window.

The Mobile Client will download the upgrade file first and then start upgrading the device.

Note:

You can also enable the Mobile Client to automatically download the upgrade file in Wi-Fi networks once a new device version is detected. For details, see Auto-Download Upgrade File.

.

UPDATING FIRMWARE

Hikvision regularly updates the firmware in our products to resolve potential issues and keep your system running smoothly. Below, you can find guidance on how to update your system accordingly.

Updating Hikvision IP Camera Firmware

To upgrade the firmware of a Hikvision IP camera, please follow the steps below:

1.Locate the appropriate firmware by clicking this link

2.Click on the firmware, then click download.

3.Agree to the license terms and conditions when prompted.

4.Locate the downloaded firmware file (this typically will be in the default download folder, unless prompted for a download location, then choose Desktop) and extract it by right-clicking on the file and selecting extract all or unzip. When prompted for an extract location, choose Desktop to extract the final file to. A file labeled DIGICAP will appear on the desktop.

5.After the file is extracted, log into the camera using Internet Explorer or Firefox web browsers. If prompted to install the plugin (or to allow the plugin to run), follow the prompt to proceed with the upgrade procedure.

6.Log into the camera using the administrator username and password, then go to the Configuration tab. In this tab, go to Basic Configuration then System, and then click on the Maintenance tab.

7.On the bottom of the page under Remote Upgrade, press the Browse button to locate and choose the firmware file, which was previously saved on the Desktop. After selecting the file, click Open, then click Upgrade.

8.The camera will display a prompt that a reboot is necessary to complete the upgrade. Click OK. The camera will reboot when the firmware is successfully upgraded.

Click here to see a video tutorial of the above steps.

Upgrading Hikvision DVR/NVR Firmware

To upgrade the firmware of a Hikvision DVR or NVR, please follow the steps below:

1.Insert a USB flash drive into the computer’s USB port (Please note that the USB flash drive does not need to be empty; it may contain other files and documents).

2.Locate the appropriate firmware by clicking this link

3.Click on the firmware, then click download.

4.Agree to the license terms and conditions when prompted.

5.Locate the downloaded firmware file (this typically will be in the default download folder, unless prompted for a download location, then choose Desktop) and extract it by right-clicking on the file and selecting extract all or unzip. When prompted for an extract location, choose the USB flash drive (typically labeled by letters E, F and so on) to extract the final file to. A file labeled DIGICAP will appear in the USB flash drive.

6.After the firmware has been extracted (unzipped), remove the USB flash drive from the computer and insert it into one of the available USB ports on the DVR/NVR unit.

7.On the DVR/NVR, go to the Main Menu, and then go to Maintenance.

8.From the sub-menus on the left click Upgrade. This will display the content of the USB flash drive.

9.Choose the DIGICAP file and press Upgrade.

10.An information window will pop up prompting that the unit will reboot after the upgrade is complete. Click YES.

11.To verify that the firmware has been upgraded, after the DVR/NVR is rebooted, go to the Main Menu, and then go to System Information. The current firmware version will be displayed.  

New Hikvision Firmwares 2024

Also Read : Hikvision How To Tutorials Chapter 1

How do I get Firmware Updates for my Hikvision Gear?

Hikvision Australia’s website has firmware updates for available IP cameras.
https://www.hikvision.com/au-en/

Use the search bar to try and find your product. Firmware updates are usually available on the product page.

IF YOU BOUGHT EQUIPMENT FROM US:

You will need to contact us if you can’t find your camera listed or if you require firmware for your NVR / DVR.
You will need to also provide the full serial number of the device as well as your current firmware.
This is to ensure upgrades are done properly. In some instances middlle firmware is required before upgrading to the latest version.

We do not recommend doing intercom firmware upgrades. Please check with us if there is any doubt.

If you didn’t buy equipment from us, please contact the people who you bought the equipment from.

How to Upgrade Camera Firmware via Hikvision NVR

This Video shows you how to upgrade your Camera firmware from the NVR.

Hikvision Australia’s website has firmware updates for available IP cameras.
https://www.hikvision.com/au-en/Support/Downloads/Firmware/IPC

NOTE this is only for IPC.

You will need to contact us if you can’t find your camera listed or if you require firmware for your NVR / DVR.
You will need to also provide the full serial number of the device as well as your current firmware.
This is to ensure upgrades are done properly. In some instances middlle firmware is required before upgrading to the latest version.

We do not recommend doing intercom firmware upgrades. Please check with us if there is any doubt.

 .

Lates Hikvision Firmwares 2024

How do I update Hikvision firmware remotely for my TetherX installation?

If your system was installed by one of our security installation partners please contact them to update your cameras. If you would like to update your Hikvision devices yourself please follow the guide below.
​

.

1.Download the latest Hikvision firmware by visiting the Hikvision Downloads Page

Hikvision Downloads Page

Note: the UK firmware is different from the US firmware. For UK firmware, please follow use the UK Downloads page.
​
​

2.Extract the firmware archive, it should contain the file: digicap.dav

3.Create a tunnel into your Hikvision device.

How to create a tunnel?

​

4.Login to your Hikvision device and navigate to “Configuration” then “Maintenance”.

​

5.At the bottom of the page under the ‘Upgrade’ header, press on “Browse”

​

6.Use the file navigator window that pops up to select the digicap.dav file you downloaded earlier
​

7.Click on ‘Upgrade’

.

The actual upgrade will take up to 10 minutes and the device will automatically reboot at the end of the upgrade process.
​
This video from Hikvision Technical Support shows the upgrade process:

.

Click here to see a video tutorial of the above steps.

00 Temperature Screening-2020-07-10

01 Density Control-2020-07-10

02 Mask Detection-2020-07-17

03 Front Ends-2020-12-02 

04 Back Ends-2023-03-15

Access Control & Video Intercom-2020-12-02

Accessaries-2021-12-01

Alarm-2023-06-21 

ANPR & Speed Radar Display-2023-07-10

Dell image-2022-12-12

Mobile-2023-07-03 

Paxton related materials-2023-05-26

Portable Series-2024-02-06 

Thermal-2023-07-07 

Transmission & Display-2022-12-16

.

DVR-2023-08-11 

IPC-2021-11-04 

NVR-2021-11-26 

PTZ-2021-09-23 

fw and model list.xlsx10.27KB2019-04-09

.

.

.

.

.

Hikvision Firmware Download –
Intelligent Traffic Products

.

Hikvision Firmware Download –
Access Control Products

.

.

.

.

.

.

<p>The post New Hikvision Firmwares 2024 first appeared on NVR IPCAMERA SECURITY.</p>

InVid Tech is here to help you succeed, and as a company, we pride ourselves on the level of personal service we offer. We have an experienced team based in the United States, including Sales, Customers Service, Marketing & Tech Support. Additionally, there is support for Latin American Countries.

Steps to Change Secure Series Camera Compression to H.264

The below steps are needed in order to connect your camera to the Secure 4ch NVR attached with your order.  Please log into camera first, default username is “admin” and default password are “1234567u”, from there it will prompt you to change, please do so and follow below steps.  If you do not do this first, the camera will not connect to the NVR.

SEC-BODYTEMPCAM1 Camera Configuration Guide

**Please Note:  Cameras Default IP address is 192.168.1.121.  IP Utility can be downloaded off our website here

• Log into the cameras web interface on Internet Explorer (IE), default username is “admin” and default password are “1234567u”. Make sure to download the new plugin. 

Note: close ALL browser tabs while installing the plugin.

• Parameter Configuration (Configuration/Human Thermometer/Parameter Configure)

◦ Enable face detection

◦ Draw the area according to the real scenario, there is a maximum of 8 areas supported. We usually use one detection area to cover where people could potentially appear in, recommended distance is 9 to 16 feet (3-5 meters) for capturing.

• Leave the Display Trace Info at “Mode 1”

• Show Detection Area, can turn On or Off

• For Confidence Coefficient, we suggest keeping the default value (Mid). It’s for the face matching level with the built-in algorithm.

• Area ID is for the selected areas if you choose more then one main area, up to 8 totals. We suggest keeping this at one and focusing on the main point of entrance.

• For Face Pixel Minimum and Maximum, we suggest keeping the default value (70/1000). Only faces in this range will be detected.

• There are two different Snapshot Modes: 

◦ Timing: ‘upload interval’ is associated with ‘timing’, camera will upload one picture every 5 seconds (Suggested).

◦ Optical: ‘snapshot count’ is associated with ‘optical’, camera will upload the best face picture in 5 seconds.

• For Upload Image Interval we suggest leaving at 5 seconds (1-10 second range).

• For Yaw Degree, Tilt Degree, Pitch Degree and OSD Overlay Snapshot, we suggest keeping as default.

• FTP Upload Image Matting and FTP Upload Whole Image are if you are using the camera as a standalone device, no CMS or NVR, and wish to save the facial snaps to an FTP.

• Temperature Parameters

• Enable this field and leave all as DEFAULT except LENGTH UNIT and MOUNT DISTANCE

◦ IF YOU SWITCH TO FAHRENHEIT THE FIELDS STILL STAY AS DEFAULT (Except Length/Mount Distance, mentioned above)

◦ DEPENDING ON THE SELECTION OF “LENGTH UNIT” (METERS/FEET), ALL DISTANCE FIELDS WILL BE CONSIDERED IN THOSE UNITS!

[IMPORTANT] Set the mount distance according to the real installation, whose value should be the horizontal distance from the detection area to the camera. 

Hit ‘apply’ to save the settings.

• Face Alarm Linkage

IF SWITCHED TO FAHRENHEIT YOU MUST ADJUST “ALARM TEMPERATURE”, 99.5-100.5F (Default Celsius is 37.30)[

• [IMPORTANT] Thermal Mapping (Configuration/Human Thermometer/Thermal Mapping)

◦ This step is mainly for matching the thermal image with the visible image, which can ensure the measurement accuracy.  The Black Body device (Infrared Calibrator) MUST be in the Field of View of the thermal image.  The thermal image is a FIXED LENS and is a smaller field of view then the standard image.

• There are eight groups of ID, and each group ID contains three points. If using One area, then you do not have to set groups 2-8.

• Pick out three points that you can clearly see in the thermal image, mark them with point1, point2 and point3.

• Find the three locations of the three points in the visible image and mark them with the same point numbers associated with those in thermal image.

◦ Note: Suggested to choose three points far away from one another, so the triangle of can cover 70% of the image.

• Hit ‘apply’ to save the settings.

• Test if the rectangle can correctly surround the face, and perfect it by adjusting the three points.

• Thermal calibration (Configuration/Human Thermometer/Thermal Calibration)

• Install the blackbody properly where the camera can see it (within the thermal image). The blackbody needs to be powered on for at least 20 mins to reach to a stable temperature.

◦ The Infrared Calibrator will ALWAYS display in CELSIUS; the stable temperature is ~40C

• Enable.

• If you turn on ‘Display Area Info’, the blackbody (Infrared Calibrator) will also be shown with temperature on thermal image.

◦ Draw box around your calibrator

• Target Temperature: If using Celsius leave as 40C, if using Fahrenheit change to 104F (Default)

• For Distance, put the real installation distance between the camera and Black Body (Infrared Calibrator). No more then 9-16 feet (3-5 meters).  Distance is in Meters or Feet, depending what you selected under the Parameter Config menu.

• Keep the ‘Emission Rate’ as the default value.

• Hit ‘apply’ to save the settings.

InVidTech Secure Series Setup Guide v1

Also Read : How To Setup O-KAM Pro camera

SEC BODYTEMPCAM1 camera run off of POE output?