How To Dahua Video Intercom All Methods

HomeGuideHow To

How To Dahua Video Intercom All Methods

How to Initialize Video Intercom using Configtool Description Initializing our Video intercom with Configtool simplifies and streamlines the process

How to Reset Hardware for Milesight
How To Setup Intrusion Detection Dahua NVR
EasternCCTV NVR DVR Firmware Software Download

Initialize Video using

Description

Initializing our Video intercom with Configtool simplifies and streamlines the process.

Configtool now handles the initialization phase and any IP address changes that need to be made. You no longer need to manually initialize our VDP devices manually

You can only Initialize the same type of Intercom at one time due to the password requirements

  • VTHs requires a 6 character password (Numerical only)
  • VTOs requires an 8 character password (Alpha Numerical combination)

Prerequisites

1. Configtool

2. Gen 3 Video Intercom devices

3. PC

1. Check the VTOs that you want to initialize and click on Initialize

Note:You can only Initialize the same type of Intercom at one time due to the password requirements

How to initialize Video Intercom using Configtool-1.png

2. Click on Initialize

How to initialize Video Intercom using Configtool-2.png

3. VTOs require at least an 8 character Alpa-Numeric password. Be sure to enter an email as this will be your method resetting the password if forgotten or lost. Click on Next to proceed

How to initialize Video Intercom using Configtool-3.png

4. The green check marks will indicate that the devices have been successfully initialized. Click on Finish to complete the VTO initialization.

How to initialize Video Intercom using Configtool-4.png

5. Select the VTHs you want to initialize and click on Initialize

Note:You can only Initialize the same type of Intercom at one time due to the password requirements

How to initialize Video Intercom using Configtool-5.png

6. Click on Initialize

How to initialize Video Intercom using Configtool-6.png

7. Enter a 6 Character Numerical password and an email as this will be your method to the password if forgotten or lost.

How to initialize Video Intercom using Configtool-7.png

8. Green check marks indicates it was successfully initialized. Click on Finish to finalize the initialization.

How to initialize Video Intercom using Configtool-8.png

Changing IP Addresses

Once devices are initialized you may want to change their IP Addresses to be on the same IP Scheme

1. To do that go to Search Setting

How to initialize Video Intercom using Configtool-9.png

2. Enter the credentials if the device you want to modify and click on OK

How to initialize Video Intercom using Configtool-10.png

3. The device list will refresh. Click on Edit for the device you want to edit

How to initialize Video Intercom using Configtool-11.png

4. Enter the desired IP Address then click on OK to finalize

How to initialize Video Intercom using Configtool-12.png

5. The green check mark will indicate that the IP address change was successful.

How to initialize Video Intercom using Configtool-13.png

How To Adjust Time Using VDPConfig

Description

This guide will show you how to adjust the time for a video intercom device over a local using VDPConfig.

Prerequisites

Video Instructions

Step by Step Instructions

1. Open DahuaToolbox and click Open next to VDPConfig

Upgrade Firmware - VDPConfig - 1.jpg

2. Discover the device in VDPConfig – How To Discover A Device Using VDPConfig

Modify IP - VDPConfig - 1.jpg

3. Click System section

VDPConfig Adjust Time - 1.jpg

4. Check the box next to the device

VDPConfig Adjust Time - 2.jpg

The time information will be displayed for the device.

To automatically sync the device time with the computer click Sync PC

Or

Enter the desired date & time for the device and click Manual Sync

VDPConfig Adjust Time - 3.jpg

A checkmark will confirm the settings change

VDPConfig Adjust Time - 4.jpg

5. Click Save

VDPConfig Adjust Time - 5.jpg

How To In VDPConfig

Description

This guide will show you how to the of a device using VDPConfig

Prerequisites

Step by Step Instructions

1. Open DahuaToolbox and click Open next to VDPConfig

Upgrade Firmware - VDPConfig - 1.jpg

2. Click the Upgrade icon on the left (Arrow)

Upgrade Firmware - VDPConfig - 2.jpg

3. Click Search Setting

Upgrade Firmware - VDPConfig - 3.jpg

4. Enter the password for the device then click OK

Upgrade Firmware - VDPConfig - 4.jpg

The window may refresh after entering a password

5. Check the box next to the device you wish to upgrade then click Browser to locate the firmware file

Upgrade Firmware - VDPConfig - 5.jpg

6. Use the window that appears to locate the firmware file

Upgrade Firmware - VDPConfig - 6.jpg

7. Click Upgrade

Upgrade Firmware - VDPConfig - 7.jpg

8. Upgrade Setup window will appear

Set Upgrade Type to Main Program

Clear Config must be enabled.

Check the box next Clear Config then click OK to begin the upgrade

Upgrade Firmware - VDPConfig - 8.jpg

9. The upgrade status will display via a progress bar

Upgrade Firmware - VDPConfig - 9.jpg

Upgrade Firmware - VDPConfig - 10.jpg

When the firmware upgrade is complete a green checkmark will appear next to the device

Upgrade Firmware - VDPConfig - 11.jpg

How To Modify System Settings In VDPConfig

Description

This guide will show you how to modify the system settings of a device over a local using VDPConfig

System settings include:

  • Time Settings (Set time, , and DST settings)
  • Device Maintenance (Reboot and Factory )
  • Device Password (Modify and reset device password)
  • Configuration

Prerequisites

Step by Step Instructions

1. Open DahuaToolbox and click Open next to VDPConfig

Upgrade Firmware - VDPConfig - 1.jpg

2. Click System Settings (screwdriver & wrench icon) on the left side of the screen

Modify System Settings - VDPConfig - 1.jpg

3. The Search Setting window will appear

Modify System Settings - VDPConfig - 2.jpg

4. Adjust the search parameters to discover the device then click OK

600PX

5. Discovered devices will appear in the device tree on the left

600PX

6. Click the Expand device tree.jpg (triangle) icon to expand the device list

600PX

Check the box next to the device(s) you wish to modify

The message in the center of the screen will display how many devices are currently selected

Timing Settings

Modify System Settings - VDPConfig - 6.jpg

Reboot/Restore

Device Password

AlarmConfig

How To Modify Network Settings In VDPConfig

Description

This guide will show you how to modify the network settings of a device over a local network using VDPConfig for configuration and .

Prerequisites

Step by Step Instructions

1. Open DahuaToolbox and click Open next to VDPConfig

Upgrade Firmware - VDPConfig - 1.jpg

2. Discover the device in VDPConfig – How To Discover A Device Using VDPConfig

Modify IP - VDPConfig - 1.jpg

3. Check the box next to the device in the list

To open network settings:

Click the Pencil icon under the Operate

OR

Click Modify IP towards the bottom of the window

Modify IP - VDPConfig - 2.jpg

4. The Modify IP Address window will appear

Modify IP - VDPConfig - 3.jpg

5. Enter all network information then click OK

Modify IP - VDPConfig - 4.jpg

6. A green check mark will appear next to the device in the list when successful:

Modify IP - VDPConfig - 5.jpg

COMMENTS

WORDPRESS: 48
DMCA.com Protection Status